Scribd
Upload
43 views4 pages

Concrete Technology Supl

Uploaded by

vvsamarth82
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
43 views4 pages

Concrete Technology Supl

Uploaded by

vvsamarth82
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

DR.

BABASAHEB AMBEDKAR TECHNOLOGICAL UNIVERSITY, LONERE


Supplementary Examination – Summer 2023
Course: B. Tech.Branch:Civil Engineering Semester :5th Sem
Subject Code & Name: BTCVC504_Concrete technology
Max Marks: 60 Date:17/08/2023 Duration: 3 Hr.
Instructions to the Students:
1. All the questions are compulsory.
2. The level of question/expected answer as per OBE or the Course Outcome (CO) on
which the question is based is mentioned in ( ) in front of the question.
3. Use of non-programmable scientific calculators is allowed.
4. Assume suitable data wherever necessary and mention it clearly.
(Level/ Marks
CO)
Q. 1 Solve Any Two of the following.
A) List the properties of fine aggregate and explain one of them in detail. CO1 6

B) Define bulking of sand and explain in detail the procedure to find the bulking of CO1 6
sand with diagram.

C) Explain the procedure to determine standard consistency of cement. CO1 6

Q.2 Solve Any Two of the following.


A) Describe the procedure for determination of workability by compaction factor test CO1 6
with diagram.

B) Explain the procedure of conducting a rebound hammer test for measuring the sur- CO1 6
face hardness with reference to following points : (i) Rebound number and its signif-
icance (ii) Construction of equipment (iii) Sketch of equipment (iv) limitations of
test

C) Define the following terms :a) Setting time of cement b) Bleeding c) Workability CO1 6

d) Durability e)Compressive Strength f) Fineness of cement

Q. 3 Solve Any Two of the following.


A) Define Admixtures. Enlist its types and state purpose of adding the admixtures into CO2 6
the concrete. (any four)

B) Define concrete mix design. Write any four factors affecting on it and state any two CO3 6
methods of concrete mix design. State necessity of concrete mix design.

C) Calculate fineness modulus for the given data of fine aggregate. Total weight of CO1 6
C.A. = 1000 gm. State type of sand.
Sieve size 4.75 2.36 1.18 600μ 300μ 150μ Pan
(mm)
Weight 100 150 300 200 120 90 40 75 210 27
retained (gm.)

Q.4 Solve Any Two of the following.


A) Explain Duff Abraham’s water cements ratio law. CO 3 6

B) Define batching with its type. Draw concreting operation chain in sequence & CO 3 6
Calculate quantity of water to be added for costing cubes in laboratory by 10 kg
cement, if w/c ratio 0.5.
C) Explain the procedure to determine the compressive strength of concrete. CO1 6

Q. 5 Solve Any one of the following.


A) a) Explain the method of concrete mix design procedure by I.S. method. CO3 12

b) Illustrate the effect of properties of coarse aggregates on compressive strength of


concrete.

B) Design a concrete mix for M45 grade using following data: CO3 12
a) Grade designation : M45
b) Type of cement : OPC 43 Grade (Specific Gravity=3.15)
c) Maximum nominal size of aggregate : 20mm (Specific Gravity=2.80)
d) Minimum cement co100 150 300 200 120 90 40ntent : 320 kg/m3
e) Maximum water-cement ratio : 0.45
f) Workability : 125 mm slump
g) Exposure condition : Severe (RCC)
h) Method of concrete placing : Pumping
i) Degree of supervision : Good
j) Type of aggregate : Crushed Angular Aggregates
k) Super Plasticizer will be used.
l) Fine aggregates: Confirming to Zone II (Specific Gravity=2.70)
*** End ***
The grid and the borders of the table will be hidden before final printing.

You might also like