0% found this document useful (0 votes)
47 views62 pages

Mackie M1200, M1400, M1400i

Uploaded by

cesar19592014
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
47 views62 pages

Mackie M1200, M1400, M1400i

Uploaded by

cesar19592014
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 62

M•1400 / M•1400i / M•1200

SERVICE MANUAL

Version 1.2 1998 MACKIE DESIGNS, INC.


820-179-00
CAUTION AVIS
CAUTION AVIS
RISK OF ELECTRIC SHOCK
DO NOT OPEN
RISQUE DE CHOC ELECTRIQUE
NE PAS OUVRIR

CAUTION: TO REDUCE THE RISK OF ATTENTION: POUR EVITER LES


ELECTRIC SHOCK DO NOT REMOVE RISQUES DE CHOC ELECTRIQUE, NE
THE COVER PAS ENLEVER LE COUVERCLE. AUCUN
NO USER SERVICEABLE PARTS INSIDE ENTRETIEN DE PIECES INTERIEURES
REFER SERVICING TO QUALIFIED PAR L'USAGER. CONFIER L'ENTRETIEN
PERSONNEL AU PERSONNEL QUALIFIE.
WARNING: TO REDUCE THE RISK OF AVIS:POUR EVITER LES RISQUES
FIRE OR ELECTRIC SHOCK, DO NOT D'INCENDIE OU D'ELECTROCUTION,
EXPOSE THIS PRODUCT TO RAIN OR N'EXPOSEZ PAS CET ARTICLE A LA
MOISTURE PLUIE OU A L'HUMIDITE.
TO PREVENT ELECTRIC SHOCK, DO POUR PREVENIR LES CHOCS
NOT USE THIS POLARIZED PLUG WITH ELECTRIQUES NE PAS UTILISER CETTE
AN EXTENSION CORD, RECEPTACLE OR FICHE POLARISEE AVEC UN
OTHER OUTLET UNLESS THE BLADES PROLONGATEUR, UN PRISE DE
CAN BE FULLY INSERTED TO PREVENT COURANT OU UNE AUTRE SORTIE DE
BLADE EXPOSURE. COURANT, SAUF SI LES LAMES
PEUVENT ETRE INSEREES A FOND
SANS LAISSER AUCUNE PARTIE A
DECOUVERT.

The lig htning fla sh w ith a rro w hea d symb o l w ithin an


e quila te ra l tria ng le is inte nd e d to a le rt the use r to the
p re se nc e o f uninsula te d "d a ng ero us v o lta g e " w ithin the
p ro d uc t's e nc lo sure , tha t m a y b e o f suffic ie nt m a g nitud e to
c onstitud e a risk o f e le c tric sho c k to pe rso ns.

Le sym b o le é c la ir av e c po int de flé c he à l'inte rie ur d 'un


tria ng le é q uila té ra l e st utilisé p o ur a le rte r l'utilisa te ur d e la
p ré se nc e à l'inte rie ur d u c o ffre t d e "vlo ta g e d a ng e re ux" no n
iso le d 'a m p le ur suffisa nte p o ur c o nstitue r un risq ue
d 'é lé c tro c utio n.

The e xc la m a tio n p o int w ithin a n e q uila te ra l tria ng le


is inte nd e d to a le rt the use r to the p re se nc e o f
imp o rta nt o p e ra ting a nd m a inte na nc e (se rvic ing )
instruc tio ns in the lite ra ture a c c o m p a nying the
a pp lia nc e .

Le p o int d 'e xc la m a tio n à l'inté rie ur d 'un tria ng le d e


la p ré se nc e d 'instruc tio ns im p o rta nte s p o ur le
fo nc tio nne m e nt e t l'e ntre tie n ( se rvic e ) d a ns le livre t
d 'instruc io n a c c o m p a g na nt L'a p p a re il.
®

TABLE O F C O NTENTS
INTRO DUC TIO N............................................................. 2
SYSTEM O VERVIEW ....................................................... 3
SUMMARY O F FEATURES .....................................................................4
SPEC IFIC ATIO NS...................................................................................6

C IRC UIT THEO RY........................................................... 8


INPUT C IRC UITRY..................................................................................8
PO WER AMPLIFIER C IRC UITRY...........................................................8
PRO TEC TIO N C IRC UITS .......................................................................9
THERMAL MANAG EMENT..................................................................10

SERVIC E PRO C EDURES............................................... 11


REQ UIRED EQ UIPMENT LIST..............................................................11
TRO UBLESHO O TING TIPS - O UTPUT FAILURES................................12
TEST AND BIASING PRO C EDURE......................................................13

PARTS............................................................................ 15
Q UIC K PARTS ......................................................................................15
C HASSIS ASSEMBLY............................................................................16
HEATSINK ASSEMBLY..........................................................................18
C O MPLETE PARTS LIST........................................................................20

SC HEMATIC S / PC B LAYO UTS.................................... 23


INPUT PC B SC HEMATIC .....................................................................23
INPUT PC B LAYO UT............................................................................24
DISPLAY PC B SC HEMATIC ................................................................25
DISPLAY PC B LAYO UT........................................................................26
MAIN PC B SC HEMATIC S...................................................................27
MAIN PC B LAYO UT............................................................................30
SO FT START PC B SC HEMATIC ...........................................................31
SO FT START PC B LAYO UT...................................................................32

Click on any item to open that page


M•1200/M•1400 SERVIC E MANUAL

INTRO DUC TIO N


This ma nua l c o nta ins c o mp le te se rvic e info rma tio n fo r the M•1200, M•1400 a nd M•1400i
a ud io p o w e r a m p lifie rs. O p e ra ting instruc tio ns w ill b e to uc he d o n b rie fly. Fo r c o m p le te
o p e ra ting instruc tio ns re fe r to the o wne r’ s m a nua l.
The FR Se rie s M•1200 a nd M•1400 a re hig h p o we r a ud io a mp lifie rs d e sig ne d fo r
p ro fe ssio na l a p p lic a tio ns. The y fe a ture a ud io p hile q ua lity so und , e xc e lle nt sta b ility,
e xte nsive p ro te c tio n c irc uitry, a nd le g e nd a ry Ma c kie re lia b ility. Pa te nte d Fa st Re c o ve ry
c irc uitry a llo ws the M•1200/ M•1400 to re c o ve r fro m c lip p ing witho ut g e ne ra ting
und e sira b le a rtifa c ts.

SERVIC E O N THE M•1200/ M•1400 IS


TO BE PERFO RMED BY EXPERIENC ED
TEC HNIC IANS O NLY!

To se rvic e the M•1200/ M•1400, te c hnic ia ns sho uld b e fa milia r with o p -a mp s, d isc re te
a na lo g c irc uitry, a nd tro ub le sho o ting hig h p o w e r so lid sta te a m p lifie rs. Pre se nta tio n o f
this m a nua l d o e s no t c o nstitute e nd o rse m e nt o f q ua lific a tio ns b y Ma c kie De sig ns.

! SMD !
The M•1200/ M•1400 ma ke s e xte nsive
use o f surfa c e mo unt c o mp o ne nts.
Se rvic ing te c hnic ia ns sho uld ha ve the
to o ls a nd e xp e rie nc e to p e rfo rm
surfa c e mo unt re wo rk.

TEC HNIC AL SUPPO RT


Ma c kie De sig ns Te c hnic a l Sup p o rt De p a rtme nt is a va ila b le 8AM - 5PM PST, Mo nd a y -
Frid a y a t 1-800-258-6883 (o utsid e US c a ll 011-425-487-4333) Ple a se fe e l fre e to c a ll with
a ny q ue stio ns (Be tte r sa fe tha n so rry!).

DISC LAIMER
The info rm a tio n c o nta ine d in this m a nua l is p ro p rie ta ry to Ma c kie De sig ns, Inc . The
e ntire m a nua l is p ro te c te d und e r c o p yrig ht a nd m a y no t b e re p ro d uc e d b y a ny m e a ns
witho ut e xp re ss writte n p e rmissio n fro m Ma c kie De sig ns, Inc .

2 INTRO DUC TIO N


VERSIO N 1.1

SYSTEM O VERVIEW
This se c tio n p ro vid e s a q uic k summa ry o f the M•1200/ M•1400’ s ma jo r fe a ture s. It is no t
inte nd e d to ta ke the p la c e o f the o wne r’ s m a nua l. It is inc lud e d he re to he lp se rvic ing
te c hnic ia ns fa milia rize the mse lve s with the M•1200/ M•1400.

DIFFERENC ES BETWEEN THE M•1400, M•1400i AND M•1200


The M•1200 a nd M•1400 a re e le c tro nic a lly id e ntic a l p ro d uc ts with the fo llo wing
e xc e p tio ns:
1. The M•1400 ha s 12,000uF ma in filte r c a p s, whe re the M•1200 a nd M•1400i ha ve
10,000uF.
2. The M•1400 a nd M•1400i use a mo re p o we rful fa n tha n the M•1200.
3. The M•1400 ha s Sp e a ko n c o nne c to rs whe re the M•1200 a nd M•1400i ha ve ¼”
sp e a ke r o utp uts (b o th in a d d itio n to b ind ing p o sts).
The M•1200 wa s d isc o ntinue d in 1998 a nd re p la c e d b y the M•1400i.
Exp o rt M•1400’ s a lso ha ve a “ So ft Sta rt” c irc uit tha t is no t insta lle d o n Am e ric a n units.

FAST REC O VERY DESIG N


So lid sta te p o w e r a m p lifie rs ha ve a re p uta tio n fo r so und ing ha rsh w he n d rive n into
c lip p ing . The usua l e xp la na tio n is o d d ha rm o nic s g e ne ra te d b y ha rd c lip p ing , b ut In
fa c t m uc h o f the unp le a sa nt so und is c a use d b y la tc hing a nd p a ra sitic o sc illa tio ns tha t
o c c ur a s the a m p lifie r re c o ve rs fro m c lip p ing .

TYPIC AL AMPLIFIER MAC KIE FR SERIES

ARTIFACTS C AUSED BY
LATCHING AND PARASITIC
O SCILLATIO N

Ma c kie ’ s Fa st Re c o ve ry d e sig n re c o ve rs fro m c lip p ing q uic kly witho ut g e ne ra ting a ny


und e sira b le a rtifa c ts. This p e rfo rm a nc e is a c hie ve d b y two uniq ue d e sig n e le m e nts; the
Full Sym m e try Dua l Diffe re ntia l fro nt e nd p ro vid e s e xc e lle nt line a rity w hile m inim izing the
ne e d fo r ne g a tive fe e d b a c k, a nd the Ba ke r C la mp p re ve nts o utp ut/ d rive r d e vic e
sa tura tio n. Ho w the se c irc uits o p e ra te is c o ve re d in d e p th in the c irc uit the o ry se c tio n.

SYSTEM O VERVIEW 3
M•1200/M•1400 SERVIC E MANUAL

SUMMARY O F FEATURES

FRO NT PANEL

1. G AIN
De te nte d g a in c o ntro ls a d just the le ve l se nt to e a c h o utp ut se c tio n. The g a in struc ture
is d e sig ne d so tha t a +4d Bu (1.23V rm s) inp ut sig na l d rive s the a m p lifie r to full ra te d
p o we r into 4Ω.

2. METERS
The M•1200/ M•1400’ s me te rs ind ic a te the re la tive o utp ut le ve l o f the a mp lifie r
re fe re nc e d to full p o we r. The SIG (sig na l p re se nt) se nse s the inp ut p rio r to the g a in
c o ntro l.

3. PRO TEC T
The Pro te c t LEDs lig ht ind ic a ting the c ha nne l ha s b e e n m ute d fo r o ne o f the fo llo wing
re a so ns:
• 4 se c o nd turn o n d e la y
• O utp ut d e vic e s b e yo nd Sa fe O p e ra ting Are a (SO A), a lso lig hts SHO RT LED(s).
• He a tsink te mp e ra ture b e yo nd 80 d e g re e s C e lsius.

4. SHO RT
The Sho rt LEDs lig ht to sho w tha t the a m p lifie r ha s e ng a g e d p ro te c tio n d ue to a sho rt o r
lo w im p e d a nc e o n the o utp ut.

5. TEMP STATUS
The HO T LED lig hts to ind ic a te tha t the a m p lifie r ha s e ng a g e d p ro te c tio n d ue to
he a tsink te mp e ra ture o r p o we r tra nsfo rme r c o re te mp e ra ture .

6. PO WER SWITC H
This re m a rka b le d e vic e re q uire s ye a rs o f stud y to full c o m p re he nd .

FULL SYMMETRY DUAL DIFFERENTIAL HIGH CURRENT DESIGN PROFESSIONALPOWER AMPLIFIER

CH GAIN /dB GAIN /dB CH CH CH


1 2
1 18
3v
20
22
OL

- 3
O
L
-3 1
3
v
2
0 2
2 INTERNALSTATUS ON
2v 8 2 2
1 2 - 6 -6 16 24 v PROTECT
6 4
1 26 - 9 -9 14 2 SHORT
4 6
- 2 - 2 TEMP STATUS OFF
8 28 0 8 2
0 8
30 3 CH

1v 01v 1& 2
COL HOT
SENSITIVITY 1.23v (+4dBu) SIG SIG 1.23v (+4dBu) D POWER
SENSITIVIT
Y

1 2 1 3 4 5 6

4 SUMMARY O F FEATURES
VERSIO N 1.1

REAR PANEL

1. SPEAKER O UTPUTS
The M•1400 ha s Sp e a ko n c o nne c to rs whe re the M•1200 ha s ¼” sp e a ke r o utp uts. Bo th
m o d e ls ha ve b ind ing p o sts. Fo r b rid g e d m o no o p e ra tio n, the + o utp ut c o m e s fro m
c ha nne l o ne ’ s p o sitive te rm ina l a nd - fro m c ha nne l tw o ’ s p o sitive .

2. INPUT
The M•1200/ M•1400 ha s b o th XLR a nd ¼” TRS inp uts. The y a re e le c tric a lly id e ntic a l
(wire d in p a ra lle l). In b rid g e d m o no o r p a ra lle l m o no m o d e c ha nne l 2 inp ut is d isa b le d .

3. THRO UG H
Ye t a no the r ja c k w ire d in p a ra lle l w ith the Inp uts, the thro ug h ja c k p ro vid e s a
c o nve nie nt w a y to c ha in a m p lifie rs o r p a ss the sig na l to a ny o the r d e vic e .

4. LO W C UT FILTER
Swe e p s the b uilt in hig h p a ss filte r fro m 10Hz to 170Hz.

5. C O NSTANT DIREC TIVITY HO RN EQ / AIR EQ


Built in she lving EQ p ro vid e s hig h fre q ue nc y c o m p e nsa tio n w he n using c o nsta nt
d ire c tivity ho rns.

6. AMP MO DE
Thre e p o sitio n slid e switc h se le c ts STEREO , PARALLEL MO NO o r BRIDG E MO NO o p e ra tio n.
C ha nne l O ne ’ s inp ut sig na l is use d fo r PARALLEL MO NO a nd BRIDG E MO NO o p e ra tio n.
AMP MO DE a nd O UTPUT APPLIC ATIO N switc he s sho uld no t b e c ha ng e d while the unit is
o n.

7. O UTPUT APPLIC ATIO N


Pla c ing the thre e p o sitio n slid e sw itc h in its c e nte r p o sitio n d e fe a ts the b uilt in LIMITER fo r
b o th c ha nne ls. Se le c ting SUB WO O FER e ng a g e s the b uilt in lo w p a ss filte r. The
FREQ UENC Y switc h se le c ts b e twe e n 125Hz a nd 63Hz c uto ff fo r the lo w p a ss filte r. In SUB
WO O FER mo d e , inp uts 1 a nd 2 a re summe d re g a rd le ss o f AMP MO DE se tting .
(Re m e m b e r, hum a n he a ring is una b le to d isc e rn d ire c tio n a t fre q ue nc ie s whe re the
wa ve le nth is g re a te r tha n the d ista nc e b e twe e n yo ur e a rs, ~250Hz unle ss yo u ha ve a
g ro ssly la rg e he a d !)

4 2 6 2 4

CAUTION 1 CHANNEL / BRIDGE / MONO AMPMODE CHANNEL 2


LOW CUT INPUT INPUT LOW CUT
STEREO MONO BRIDGE FILTER
FILTER TYPICAL
BALANCED BALANCED
O O
TYPICAL UNBALAN
R CED TYPIC
35Hz AL
UNBAL
RANCED
(MONO BRIDGE) 35 Hz
1200W A TTS STAGE STAGE
MONITOR MONITOR
4 OHM LOAD MIN.
600 W A TTSCH MONO
BRIDGE 100Hz OUTPUTAPPLICATION 100Hz
2OHMSLOADMIN.
+ -
CH CH OFF 170Hz OFF 170Hz
FULL SUB

1 2 CONSTANTDIRECTIV ITY
RANGE

LIMITER (CH1 & CH2)


WOOFER

CONSTANTDIRECTIV ITY
+ + HORNEQ/AIR EQ
4.5 kHz STEREO
FREQUENCY
HORN EQ /AIR EQ
4.5k Hz
ON TYPICAL 125Hz ON

- -
120VAC 50/60 Hz 2k Hz 6k Hz ON OFF 63Hz 2k Hz 6k Hz
1500 WATTS AIR EQ OFF OFF AIR EQ
TYPICAL TYPICAL
SPEAKER OUTPUTS THRU THRU

1 5 3 7 3 5

SYSTEM O VERVIEW 5
M•1200/M•1400 SERVIC E MANUAL

SPEC IFIC ATIO NS


No te : Po we r ra ting s a re sp e c ifie d a t
C O NTINUO US AVERAG E O UTPUT 120VAC (U.S. a nd C a na d a ) a nd 240VAC
PO WER, BO TH C HANNELS DRIVEN: (Exp o rt) line vo lta g e s.
M•1200 The M•1200/ M•1400 p o w e r a m p lifie rs d ra w
la rg e a m o unts o f c urre nt fro m the AC line w ith
225 w a tts p e r c ha nne l into 8 o hm s fro m 20Hz to c o ntinuo us sine w a ve te sting . Ac c ura te
20kHz, w ith no m o re tha n 0.025% THD m e a sure m e nt o f p o w e r re q uire s a ste a d y a nd
400 w a tts p e r c ha nne l into 4 o hm s fro m 20Hz to sta b le AC sup p ly. This m e a ns the line
20kHz, w ith no m o re tha n 0.050% THD im p e d a nc e m ust b e ve ry lo w to insure tha t the
600 w a tts p e r c ha nne l into 2 o hm s fro m 20Hz to p e a k AC line vo lta g e d o e s no t sa g to le ss tha n
20kHz, w ith no m o re tha n 0.095% THD 97% o f its va lue .
If d riving hig hly re a c tive lo a d s, w e re c o m m e nd
Bridg e d m o no o pe ra tio n:
tha t the lim ite r c irc uit b e e ng a g e d .
800 w a tts into 8 o hm s fro m 20Hz to 20kHz, w ith
no m o re tha n 0.050% THD PO WER BANDWIDTH:
1200 w a tts into 4 o hm s fro m 20Hz to 20kHz, w ith 20Hz to 70kHz (+0, –3 d B)
no m o re tha n 0.095% THD
Ma ximum Po we r a t 1% THD: FREQ UENC Y RESPO NSE:
250 w a tts p e r c ha nne l into 8 o hm s 20Hz to 40kHz (+0, –1 d B)
425 w a tts p e r c ha nne l into 4 o hm s 10Hz to 70kHz (+0, –3 d B)
640 w a tts p e r c ha nne l into 2 o hm s
850 w a tts into 8 o hm s b rid g e d DISTO RTIO N:
1280 w a tts into 4 o hm s b rid g e d
THD, SMPTE IMD, TIM < 0.025% @ 8Ω
M•1400 / M•1400i < 0.050% @ 4Ω
250 w a tts p e r c ha nne l into 8 o hm s fro m 20Hz to < 0.150% @ 2Ω
20kHz, w ith no m o re tha n 0.012% THD
425 w a tts p e r c ha nne l into 4 o hm s fro m 20Hz to SIG NAL-TO -NO ISE RATIO :
20kHz, w ith no m o re tha n 0.025% THD > 107 d B b e lo w ra te d p o w e r into 4 o hm s
630 w a tts p e r c ha nne l into 2 o hm s fro m 20Hz to
20kHz, w ith no m o re tha n 0.050% THD C HANNEL SEPARATIO N:
Brid g e d m o no o p e ra tio n: > 80 d B @ 1kHz

850 w a tts into 8 o hm s fro m 20Hz to 20kHz, w ith


no m o re tha n 0.025% THD DAMPING FAC TO R:
1260 w a tts into 4 o hm s fro m 20Hz to 20kHz, w ith 350 m inim um
no m o re tha n 0.050% THD
INPUT IMPEDANC E:
Ma xim um Po we r a t 1% THD:
20k b a la nc e d b rid g ing
300 w a tts p e r c ha nne l into 8 o hm s
500 w a tts p e r c ha nne l into 4 o hm s
700 w a tts p e r c ha nne l into 2 o hm s INPUT SENSITIVITY:
1000 w a tts into 8 o hm s b rid g e d 1.23 vo lts (+4 d Bu) fo r ra te d p o w e r into 4 o hm s
1400 w a tts into 4 o hm s b rid g e d
G AIN:
30.25 d B (32.5V/ V)

MAXIMUM INPUT LEVEL:


9.75 vo lts (+22 d Bu)

6 SPEC IFIC ATIO NS


VERSIO N 1.1

RISE TIME: LIMITER SEC TIO N:


< 4.4µs C o m p le m e nta ry Po sitive a nd Ne g a tive Pe a k
De te c ting
SLEW RATE:
Vo lta g e Sle w Ra te > 50V/ µs INDIC ATO RS:
> 100V/ µs b rid g e d 6 m e te r LEDs p e r c ha nne l
C urre nt Sle w Ra te > 32A/ µs a t 2Ω SIG (Sig na l Pre se nt), –20, –9, –6, –3, O L
(O ve rlo a d )

C MRR: CH 1 & 2
PRO TEC T LEDs
> 40 d B, 20Hz to 20kHz
SHO RT LEDs
TEMP STATUS
LO AD ANG LE:
C O LD/ HO T LEDs
8(±jx) tim e ind e p e nd e nt a t 8 Ω
4(±jx) tim e d e p e nd e nt, T > 6 m in. a t 4 Ω
PO WER C O NSUMPTIO N:
2(1±jx) tim e d e p e nd e nt, T > 2 m in. a t 2 Ω
65 w a tts a t id le
900 w a tts w ith m usic a l p ro g ra m fully lo a d e d
TRANSIENT REC O VERY:
(2 o hm s p e r sid e , o r 4 o hm s b rid g e d )
< 1µs fo r 20 d B o ve rd rive @ 1kHz 550 w a tts w ith m usic a l p ro g ra m fully lo a d e d
(4 o hm s p e r sid e , o r 8 o hm s b rid g e d )
HIG H FREQ UENC Y O VERLO AD AND 850 w a tts a t full p o w e r into 8 o hm s
(c o ntinuo us sine w a ve )
LATC HING :
1500 w a tts a t full p o w e r into 4 o hm s
No la tc h up a t a ny fre q ue nc y o r le ve l. (c o ntinuo us sine w a ve )
2500 w a tts a t full p o w e r into 2 o hm s
HIG H FREQ UENC Y STABILITY: (c o ntinuo us sine w a ve )
Unc o nd itio na lly sta b le d riving a ny re a c tive o r
c a p a c itive lo a d . AC LINE PO WER:
US 120VAC , 60Hz
TURN O N DELAY: Euro p e 240VAC , 50/ 60Hz
3 se c o nd s Ja p a n 100VAC , 50/ 60Hz
Ko re a 220VAC , 60Hz

VARIABLE LO W-C UT FILTER:


AC DRO P-O UT VO LTAG E:
10Hz (O ff) to 170Hz, 2nd O rd e r Be sse l
At a p p ro xim a te ly 50% o f ra te d line vo lta g e

SUBWO O FER LO W-PASS FILTER:


PHYSIC AL:
Sw itc he d : 63Hz/ 125Hz, 3rd O rd e r Be sse l
He ig ht 3.5 inc he s (89m m )
Wid th 19.0 inc he s (483m m )
C O NSTANT DIREC TIVITY HIG H De p th 15.25 inc he s (387m m )
FREQ UENC Y BO O ST: O ve ra ll De p th 16.25 inc he s (413m m )
2kHz to 6kHz (+3 d B p o ints) Ha nd le De p th 1.25 inc he s (32m m )
6 d B/ o c ta ve hig h-fre q ue nc y she lving filte r, We ig ht 36 p o und s (16.3kg )
(she lving o c c urs a t a p p ro xim a te ly 30kHz)
Sinc e w e a re a lw a ys striving to m a ke o ur stuff
b e tte r a t Ma c kie De sig ns b y inc o rp o ra ting ne w
a nd im p ro ve d m a te ria ls, c o m p o ne nts, a nd
m a nufa c turing m e tho d s, w e re se rve the rig ht to
c ha ng e the se sp e c ific a tio ns a t a ny tim e
w itho ut no tic e .

SPEC IFIC ATIO NS 7


M•1200/M•1400 SERVIC E MANUAL

C IRC UIT THEO RY


Muc h o f the c irc uitry in the M•1200/ M•1400 is se lf e xp la na to ry fro m the sc he ma tic . This
se c tio n will e xp la in the uniq ue c irc uits a nd a rc hite c ture . Sa m p le s in this se c tio n will re fe r
to C ha nne l 1 (Le ft) fo r c irc uitry tha t is id e ntic a l o n b o th c ha nne ls.

INPUT C IRC UITRY


Re fe r to sc he ma tic o n p a g e 23.
The sig na l p a th b e g ins with the INPUT BO ARD. Fo llo wing C ha nne l 1’ s inp ut, sig na l is fe d
to a unity g a in d iffe re ntia l o p -a m p , U1A. The sig na l is ne xt se nt to U1B whic h se rve s a s
b o th HPF a nd C D ho rn EQ . If no t in SUBWO O FER m o d e , the sum m ing a m p (U2B) a nd
LPF’ s (U3A, U3B) a re b yp a sse d . The sig na l is se nt via J11 to the g a in c o ntro l o n the
DISPLAY BO ARD. Afte r the g a in c o ntro l, the sig na l is b uffe re d b y U7A, re turne d to the
INPUT BO ARD a nd ro ute d to the MAIN BO ARD via J16.
C ha nne l 2’ s inp ut sig na l p a th is e le c tric a lly id e ntic a l to C ha nne l 1’ s in STEREO m o d e . In
PARALLEL MO NO mo d e C ha nne l 2’ s inp ut sig na l is ig no re d a nd C ha nne l 1’ s inp ut is se nt
to C ha nne l 2’ s g a in c o ntro l via SW5A. Fo r BRIDG E MO NO o p e ra tio n, C ha nne l 1’ s inp ut
sig na l is inve rte d b y U2A a nd ro ute d to the MAIN BO ARD via SW5C .

PO WER AMPLIFIER C IRC UITRY


Re fe r to sc he ma tic o n p a g e 27.
The M•1200/ M•1400 use a c la ss AB trip le d a rling to n o utp ut w ith c o m p le m e nta ry o utp ut
d e vic e s. The m a in p o we r sup p ly is +/ - 80V, the re is a lso a +/ - 90V sup p ly fo r the fro nt
e nd c irc uitry. C ha nne ls a re m ute d fo r 4 se c o nd s o n p o we r up a s C 53 c ha rg e s via R203.
Muting is a c hie ve d b y turning o ff Q 73, re m o ving c urre nt so urc e s fo r the d iffe re ntia l p a irs.
(Wa it a minute ! PAIRS? Re a d o n…)
An im m e d ia te ly o b vio us d e p a rture fro m sta nd a rd d e sig ns is the Dua l Diffe re ntia ls a nd
Symme tric a l Vo lta g e Amp s. The re a so ning b e hind this fro nt e nd a rc hite c ture is
a c tua lly q uite sim p le . Tra nsisto rs tra nsfe r c ha ra c te ristic s a re no t e ntire ly line a r, so e ve n
the b e st c o nve ntio na l fro nt e nd d e sig n will intro d uc e so m e d isto rtio n. Mo st a m p lifie rs
use ne g a tive fe e d b a c k to re d uc e this p ro b le m (c re a ting a fe w mo re in the p ro c e ss).
Ma c kie FR Se rie s a mp lifie rs ta ke a d iffe re nt a p p ro a c h. By using two c o mp le me nta ry
“ m irro r im a g e ” fro nt e nd c irc uits a ny d isto rtio n c a use d b y no n-line a r tra nsisto r c urve s is
e ffe c tive ly c a nc e le d o ut in the b ia s string , witho ut fe e d b a c k!
Ano the r d e sig n fe a ture uniq ue to Ma c kie FR Se rie s Amp lifie rs is the Ba ke r C la mp . The
Ba ke r C la mp ha s two func tio ns; 1) Pre ve nt o utp ut/ d rive r tra nsisto rs sa tura ting , 2) Drive
the LIMITER LDR. Re fe rring to the le ft ma in a mp sc he ma tic , Q 27 is a c o mmo n b a se
a m p lifie r, it w ill turn o n if Q 31’ s c o lle c to r rise s m o re tha n tw o d io d e d ro p s a b o ve the
+80V sup p ly, p re ve nting it fro m rising furthe r. The re a re thre e d io d e d ro p s b e twe e n
Q 31’ s c o lle c to r a nd the b a se o f d rive r tra nsisto r Q 28 (D3, D2, Q 29Vb e ). Q 29 will ne ve r
se e a vo lta g e g re a te r tha n o ne d io d e d ro p b e lo w the +80V sup p ly, e ve n if the +80V
sup p ly fluc tua te s. Q 27 a lso d rive s the limite r LDR LED U2A. The ne g a tive sid e ha s the
sa m e c irc uit m irro re d .

8 C IRC UIT THEO RY


VERSIO N 1.1

PRO TEC TIO N C IRC UITS


Re fe r to sc he ma tic s o n p a g e s 27-29.
The M•1200/ M•1400 ha s two o utp ut p ro te c tio n c irc uits in a d d itio n to the ra il fuse s. The
first m ute s the a m p if the o utp ut d e vic e s a re lo a d e d b e yo nd the ir sa fe o p e ra ting a re a
(SO A). The se c o nd is a c ro wb a r c irc uit tha t e nsure s the ra il fuse s b lo w if the re is DC o n
the o utp ut.

SO A PRO TEC TIO N


The SO A p ro te c tio n c irc uit se nse s the vo lta g e d ro p a c ro ss the e mitte r re sisto rs muc h like
sta nd a rd VI c urre nt lim iting tra nsisto rs. Q 76 a nd Q 77 w ill turn o n if the e m itte r d ro p
e xc e e d s ~1V. If the y a re o n fo r lo ng e no ug h to c ha rg e C 38 (thro ug h R159), the SO A
p ro te c tio n c irc uit is a c tiva te d b y tra nsisto r switc he s Q 79 a nd Q 78.
If SO A d e te c tio n is trip p e d , the c ha nne l is m ute d b y d isc ha rg ing C 53 thro ug h R200 a nd
D65, fa n sp e e d is inc re a se d , a nd the “ SHO RT” LED lig hts.

DC C RO WBARS
The DC C ro wb a r c irc uit p ro te c ts sp e a ke rs in the e ve nt o f a n o utp ut fa ilure b y b lo wing
a ll ra il fuse s. SC Rs Q 21-24 a re use d to sho rt the +/ - 80V sup p ly sup p lie s to g ro und .
O utp ut sig na l fro m b o th sid e s is fe d thro ug h 100K re sisto rs R90, R89 to C 21, e sse ntia lly
fo rm ing a LPF. DC o n e ithe r o utp ut will trig g e r c o m p a ra to r U4A (p o sitive ) o r U4B
(ne g a tive ). The SC Rs a re the n fire d via d rive r tra nsisto rs Q 87, Q 88.

NO TE:
The LM339 c o m p a ra to r IC is use d e xte nsive ly in the
M•1200/ M•1400. It d iffe rs fro m a sta nd a rd o p -a mp
use d a s a c o m p a ra to r in tha t it ha s a n o p e n
c o lle c to r o utp ut. If the vo lta g e a t the inve rting inp ut
e xc e e d s the no n-inve rting , the LM339’ s o utp ut
switc he s to it’ s ne g a tive sup p ly. O the rwise , the
o utp ut is o p e n.

C IRC UIT THEO RY 9


M•1200/M•1400 SERVIC E MANUAL

THERMAL MANAG EMENT


Re fe r to sc he ma tic o n p a g e 29.
The M•1200/ M•1400 T-De sig n He a tsink/ Fa n c o o ls o utp ut d e vic e s e ve nly a nd d o e s no t
c o lle c t d ust o n the c irc uitry. The fa n o p e ra te s a t two sp e e d s, c o ntro lle d b y the
a mp lifie r. An LM35DZ mo unte d in the c e nte r o f the he a tsink p ro vid e s te mp e ra ture
info rm a tio n to the fa n c o ntro l a nd o ve rte m p c irc uits. The re is a lso a the rm a l b re a ke r in
the p o we r tra nsfo rme r.

FAN C O NTRO L C IRC UIT


The fa n vo lta g e c o m e s fro m a fe e d b a c k re g ula to r c irc uit fo rm e d b y Q 91 a nd Q 92. The
o utp ut vo lta g e is p ro g ra mme d b y the ra tio o f R209 to R211/ / R207 (/ / =p a ra lle l). Whe n
the unit is p o we re d up C 83 c ha rg e s thro ug h R241 p ro vid ing a 40 se c o nd d e la y b e fo re
the fa n sta rts. As C 83 c ha rg e s, U6D’ s o utp ut switc he s to -16V, sta rting the fa n. The n
U6A’ s o utp ut switc he s to o p e n, a llo wing U6B to inc re a se the fa n sp e e d , if trig g e re d . R240
a nd C 82 g ive the fa n e xtra vo lta g e whe n sta rting .
The fa n sp e e d is inc re a se d b y U6B a d d ing R211 in p a ra lle l with R207. (Q 91 wa nts it’ s
b a se a d io d e d ro p a b o ve g ro und , so Q 92 d o ub le s its Em itte r vo lta g e ). U6B is trig g e re d
b y U4D to inc re a se fa n sp e e d if;
• C ha nne l 1 SO A p ro te c tio n is a c tiva te d (U5C ), O R
• C ha nne l 2 SO A p ro te c tio n is a c tiva te d (U5D), O R
• The he a tsink is a b o ve 60 d e g C (U5B) AND p ro g ra m is d e te c te d (U4C ), O R
• The he a tsink te m p e ra ture is a b o ve 80 d e g C (U5A).
U6C a nd Q 89 a re use d to re se t the c irc uit o n p o we r d o wn. Und e r no rm a l o p e ra tio n
C 50 is c ha rg e d via D57, Ho ld ing Q 89 o ff. Whe n p o we r is re m o ve d C 50 d isc ha rg e s a nd
Q 89 switc he s o n a s the ra ils c o lla p se . Whe n the vo lta g e o n Q 89’ s c o lle c to r fa lls b e lo w
g ro und U6 switc he s to the ne g a tive ra il d isc ha rg ing C 82 a nd C 83.

THERMAL SHUTDO WN
Extre me he a tsink o r tra nsfo rme r c o re te mp e ra ture will a c tiva te O VERTEMP. U5A
a c tiva te s o ve rte mp if the LM35DZ d e te c ts he a tsink te mp e ra ture a b o ve 80 d e g C .
Fe e d b a c k re sisto r R137 re sc a le s U5A’ s vo lta g e re fe re nc e so tha t the he a tsink must c o o l
to b e lo w 50 d e g C b e fo re o ve rte m p is d e a c tiva te d . O ve rte m p c a n a lso b e a c tiva te d
b y the p o we r tra nsfo rm e r the rm a l b re a ke r (via Q 89). In e ithe r c a se , b o th c ha nne l a re
mute d via D69 a nd D66.

10 C IRC UIT THEO RY


VERSIO N 1.1

SERVIC E PRO C EDURES


MEC HANIC AL PRO C EDURES
The M•1200/ M•1400 d e sig n a llo ws e a sy re mo va l o f a ll c o mp o ne nts a nd a sse mb lie s.
Disa sse m b ly a nd re a sse m b ly sho uld b e se lf e vid e nt. This m a nua l ha s e xp lo d e d
d ia g ra m s in the p a rts se c tio n.
Se ve ra l im p o rta nt p o ints c o nc e rning the a sse m b ly:
• 4 o f the sc re ws tha t se c ure the to p c o ve r a lso ho ld the fro nt e xtrusio n (c urve d
p ie c e ) in p la c e . Whe n re m o ving the to p c o ve r, b e c a re ful tha t the fro nt e xtrusio n is
no t d ro p p e d .
• If the MAIN PC B is re mo ve d , b e sure the sma lle r he a d ma c hine sc re ws (750-050-04)
a re re p la c e d ne xt to the filte r c a p s. The la rg e r he a d ma c hine sc re ws c a n a rc to the
c a p a c ito r b o d y.
• Be sure a ll tyw ra p s a re re p la c e d a nd tha t no w ire s a re in d a ng e r o f b e ing p inc he d
in-b e twe e n the c o ve r a nd he a tsink.

REQ UIRED EQ UIPMENT LIST


• 30 MHz d ua l tra c e o sc illo sc o p e
• DMM (Must b e c a p a b le o f me a suring 8mV DC with a minimum o f 2 d ig its o f
a c c ura c y, a nd d o wn to .1Ω)
• Sine wa ve o sc illa to r / Func tio n g e ne ra to r (20Hz - 20KHz)
• 4 lo a d re sisto rs (8Ω with a minimum 500W p o we r ra ting )
• 10A / 120V Va ria c With AC vo ltm e te r a nd a d e fe a ta b le a mme te r (1 Amp full ra ng e )
o r wa ttme te r (300 Wa tts full ra ng e )
• 0.1uF 400V film c a p a c ito r insta lle d a c ro ss d ua l b a na na p lug
• 16 AWG sho rting jum p e r insta lle d a c ro ss d ua l b a na na p lug

REC O MMENDED EQ UIPMENT LIST (PERFO RMANC E VERIFIC ATIO N)


• Disto rtio n a na lyze r a nd lo w d isto rtio n o sc illa to r.
(C a p a b le o f re so lving d isto rtio n a s lo w a s 0.002% fro m 20Hz to 20KHz)
• 2500W AC p o we r so urc e .

SERVIC E PRO C EDURES 11


M•1200/M•1400 SERVIC E MANUAL

TRO UBLESHO O TING TIPS - O UTPUT FAILURES


Afte r a c a ta stro p hic fa ilure , it is like ly tha t the fo ur +/ -80V sup p ly fuse s will b e b lo wn.
Re p la c e fuse s a nd ve ry slo wly b ring up the Va ria c w hile m o nito ring line c o nsum p tio n. It
is like ly tha t sub sta ntia l line c urre nt will b e p ulle d d ue to sho rte d o utp ut p a rts. At the
sa me time , lo o k fo r DC o ffse t a t the o utp ut. O ffse t o f g re a te r tha n +/ - 2.8V will trig g e r
the p ro te c tio n c irc uits a nd re -b lo w the fo ur fuse s. Ke e p the o utp ut o ffse t b e lo w +/ - 2V,
o r te mp o ra rily d e fe a t the DC -o ffse t d e te c to r (Lift o ne sid e o f D56).
Re m o ve the m a in b o a rd fro m the unit a nd c he c k fo r sho rte d o utp ut tra nsisto rs. If o ne
b a d o utp ut is fo und , re p la c e a ll e ig ht in the c ha nne l. Whe n a n o utp ut d e vic e sho rts it
c a n p la c e hig h c urre nt stre sse s o n the o the r o utp ut p a rts. The se o utp ut p a rts c a n fa il
o ve r tim e . Sinc e lo ng te rm re lia b ility is p a ra m o unt, p le a se re p la c e a ll the o utp uts.
All e ig ht o f the 3W 0.22Ω e m itte r re sisto rs m ust b e ve rifie d fo r p ro p e r va lue . Any o ff-
to le ra nc e , o r o p e n p a rts, ne e d to b e re p la c e d . An o ff to le ra nc e (hig he r re sista nc e )
e m itte r re sisto r will p re ve nt it’ s re la te d o utp ut tra nsisto r fro m “ d o ing it’ s sha re ” a nd will
p la c e mo re stre ss o n it’ s ma te s in the o utp ut se c tio n. Also ve rify the 8 b a se d rive re sisto rs
(2.2Ω, 1/ 4W, fusib le ) a re a ll O K. Ve rify tha t the d rive rs a nd p re -d rive rs a re no t sho rte d . If
o ne d rive r is sho rte d re p la c e it’ s ma te . Do the sa me with the p re -d rive rs. Also c he c k a ll
the re sisto rs surro und ing the d rive rs a nd p re -d rive rs.
C he c k the VI limite rs a nd d e te c to rs. It is no t unc o mmo n to d a ma g e the se p a rts whe n
the a mp lifie r fa ils in a sp e c ta c ula r wa y! Lo o k fo r sho rts o n Q 76, Q 77, Q 94, Q 95, Q 83,
Q 84, Q 96, a nd Q 97. Ve rify p ro p e r va lue o n the re sisto rs tha t g o to the b a se s o f the se
d e vic e s. It is c ritic a l tha t the se se c tio ns a re wo rking c o rre c tly. Sho rte d tra nsisto rs c a n
c a use so m e o d d a sym m e tric a l c lip p ing p ro b le m s. O p e n p a rts will no t a llo w the c urre nt
lim iting to o p e ra te e ffe c tive ly. If p ro b le m s e xist in the se se c tio ns the a m p lifie r m ig ht fa il
into a sho rt, o r m ig ht c lip p re m a ture ly w he n lo a d e d to 2 Ω.
All o f the a b o ve tro ub le sho o ting (No t inc lud ing p a rt re p la c e m e nt) ta ke s p e rha p s 15 to
30 m inute s to d o . If yo u ta ke the tim e , a nd d o a ll tha t is ind ic a te d a b o ve , it w ill a llo w
99% o f the a m p lifie rs to c o m e up the first tim e ! Trying to hurry, a nd skip p ing wha t is
sug g e ste d , c a n le a d to a frustra ting a nd tim e c o nsum ing re p a ir.
Slo w ly b ring up the sup p ly a nd ve rify tha t line c o nsum p tio n isn’ t e xc e ssive a nd tha t the
o utp ut is c e nte re d (no DC o ffse t). It mig ht b e d e sira b le to d e fe a t the a mp lifie r muting
(C o nne c t U5-12, 13, & 14 to g e the r) te mp o ra rily so the a mp lifie rs a re a c tive e ve n whe n
the sup p lie s a re still ve ry lo w. If the a m p sta ys c e nte re d , ve rify tha t it will p a ss a nic e
c le a n sine wa ve . Re mo ve a ny te st jump e rs (I.E. DC -fa ult d e fe a t & muting d e fe a t) a nd
p ro c e e d to the “ Re lia b ility Ve rific a tio n” se c tio n.

12 SERVIC E PRO C EDURES


VERSIO N 1.1

BIAS AND TEST PRO C EDURE


Afte r the unit ha s b e e n re p a ire d , the fo llo wing sho uld b e d o ne to a ssure lo ng te rm
re lia b le o p e ra tio n. If a d isto rtio n a na lyze r is p re se nt, d isto rtio n sp e c ific a tio ns sho uld b e
ve rifie d .
1. Ad justs b ia s in b o th c ha nne ls (R1 & R51) fo r 8mV +/ - 0.3mV a t b ia s te st p o ints (J53 &
J54) a fte r unit ha s id le d fo r a fe w m inute s. With Full AC line vo lta g e a p p lie d to unit,
it will p ull a ro und 65W fro m the line (900mA a t 120V). Me a sure fo r DC o ffse t o n b o th
o utp ut c o nne c to rs. DC o ffse t sho uld b e le ss tha n +/ - 50mV.
2. Ap p ly a 1KHz sine w a ve to the inp uts a nd ve rify tha t the unlo a d e d o utp uts ha ve a
w a ve fo rm tha t is sym m e tric a l a nd und isto rte d . Drive the o utp uts into c lip p ing a nd
ve rify sym m e tric a l “ fla t-to p p ing ” o n the wa ve fo rm .
3. Re d uc e o utp ut le ve ls, insta ll the 0.1uF c a p a c ito r jum p e r fro m the o utp ut to g ro und
c o nne c tio ns, a nd ve rify tha t c lip p ing b e ha vio r is p ro p e r. Ve rify tha t no hig h
fre q ue nc y o sc illa tio n o c c urs ne a r a nd a t c lip p ing (p a ra sitic o sc illa tio n).
4. Re m o ve c a p a c itive lo a d ing a nd m inim ize sine o utp ut. Ve rify a nd re -a d just b ia s if
re q uire d . No te tha t the b ia s w ill no t d rift a p p re c ia b ly in a unit tha t is func tio ning
p ro p e rly.
5. C o nne c t the a m p lifie r d ire c tly to the AC line a nd c o nne c t a n 8Ω d um m y lo a d to
b o th c ha nne ls. Bring sine w a ve le ve l up o n b o th c ha nne ls a nd ve rify sym m e tric a l
c lip p ing . The o utp ut will c lip so me whe re b e twe e n 120V - 140V p k/ p k d e p e nd ing o n
ho w stiff the line is. C lip p ing sho uld b e a s d e sc rib e d a b o ve . Ad d the 0.1uF
c a p a c itive lo a d ing a nd ve rify c lip p ing is still w e ll b e ha ve d .
6. Ind ivid ua lly lo a d C ha nne l 1 a nd C ha nne l 2 w ith 2 Ω. C lip p ing sho uld b e
symme tric a l, we ll b e ha ve d , a nd o c c ur so me whe re a ro und 80V - 100V p k/ p k. Ve rify
tha t c lip p ing is w e ll b e ha ve d a fte r a d d ing the 0.1uF c a p a c itive lo a d ing .
7. Re d uc e o utp ut le ve l to 20V p k/ p k a nd sho rt first c ha nne l o ne a nd the n c ha nne l
two . The fro nt p a ne l “ sho rt” a nd “ p ro te c t” LEDs sho uld fla sh o n the re sp e c tive
c ha nne ls.
8. Pla c e a m p lifie r in b rid g e m o d e a nd c o nne c t 4 Ω lo a d ing to b rid g e o utp uts (a c ro ss
b o th “ +” o utp ut b ind ing p o sts). Slip so m e c a rd sto c k b e twe e n the he a tsink-o utle ts
a nd c ha ssis sid e s. Mo nito r o ne o f the o utp uts a nd a d just fo r a 20V p k/ p k sig na l.
Sho rt a c ro ss b o th o utp uts a nd ve rify tha t a ll fo ur ‘ Sho rt” a nd “ Pro te c t” LEDs lig ht a nd
the a mp lifie r mute s.
9. Re m o ve sho rt, m o nito r o ne o f the o utp uts, a nd a d just fo r a 60V p k/ p k sine o utp ut
(450W o f o utp ut p o we r b rid g e d ). Afte r a fe w minute s the fa n will b e g in running fa st
(he a tsink a t 60°C ) a nd a sho rt tim e la te r the a m p lifie r will m ute (he a tsink a t 80°C ).
The “ Ho t” a nd “ p ro te c t” LEDs will c o me o n. Re mo ve c a rd sto c k a nd a fte r a fe w
m inute s the a m p lifie r will c o m e o ut o f m ute m o d e a nd the “ c o ld ” LED will re turn.

10. Disc o nne c t lo a d ing a nd re m o ve d rive . Re c o nne c t a m p lifie r to Va ria c a nd c o nfirm


tha t the id le c o nsump tio n is ro ug hly 65W o r 900mA, a s b e fo re . C o nne c t the
a m p lifie r to sp e a ke rs a nd ve rify tha t it so und s O K with m usic .

SERVIC E PRO C EDURES 13


M•1200/M•1400 SERVIC E MANUAL

(THIS PAG E UNINTENTIO NALLY LEFT BLANK), THO SE RESPO NSIBLE HAVE BEEN PUT TO THE SWO RD

14 SERVIC E PRO C EDURES


VERSIO N 1.1

PARTS
Q UIC K PARTS

FRO NT PANEL

FULL SYMMETRY DUAL DIFFERENTIAL HIGH CURRENT DESIGN PROFESSIONALPOWER AMPLIFIER

CH GAIN /dB GAIN /dB CH CH CH


1 2
1 18
3v
20
22
OL

- 3
O
L
-3 1
3
v
2
0 2
2 INTERNALSTATUS ON
2v 8 2 2
1 2 - 6 -6 16 24 v PROTECT
6 4
1 26 - 9 -9 14 2 SHORT
4 6
- 2 - 2 TEMP STATUS OFF
8 28 0 8 2
0 8
30 3 CH
1v 01v 1& 2
COL HOT
SENSITIVITY 1.23v (+4dBu) SIG SIG 1.23v (+4dBu) D POWER
SENSITIVIT
Y

HANDLE ASSEMBLYS G AIN C O NTRO LS ALL LEDS PO WER SWITC H


RIG HT, 080-023-10 5KL PO T, 130-036-00 RED T-1, 304-001-00 500-022-00
LEFT, 080-023-20 KNO B, 760-061-00 G REEN T-1, 304-004-00
SC REW(TO C HASSIS),700-028-04 NUT, 705-013-00
STAR WASHER, 710-023-00

REAR PANEL

CAUTION 1 CHANNEL / BRIDGE / MONO AMPMODE CHANNEL


2
LOW CUT
INPUT INPUT LOW CUT
STEREO MONO BRIDGE FILTER
FILTER TYPICAL
BALANCED BALANCED
O O
TYPICAL UNBALAN
R CED TYPIC
35Hz AL
UNBAL
RANCED
(MONO BRIDGE) 35 Hz
1200W A TTS STAGE STAGE
MONITOR MONITOR
4 OHM LOAD MIN.
600 W A TTSCH MONO
BRIDGE 100Hz OUTPUTAPPLICATION 100Hz
2OHMSLOADMIN. + -
CH CH OFF 170Hz OFF 170Hz
FULL SUB

1 2 CONSTANTDIRECTIV ITY
RANGE

LIMITER (CH1 & CH2)


WOOFER

CONSTANTDIRECTIV ITY
+ + HORNEQ/AIR EQ
4.5 kHz STEREO
FREQUENCY
HORN EQ /AIR EQ
4.5k Hz
ON TYPICAL 125Hz ON

- -
120VAC 50/60 Hz 2k Hz 6k Hz ON OFF 63Hz 2k Hz 6k Hz
1500 WATTS AIR EQ OFF OFF AIR EQ
TYPICAL TYPICAL
SPEAKER OUTPUTS THRU THRU

AC LINE C O RD SPEAKER O UTPUTS INPUT SEC TIO N


US, 640-006-00 BINDING PO STS, 400-119-00 ALL KNO BS, 760-048-04
EURO PE, 640-007-01 BINDING PO ST SC REW, 700-011-00 LO W C UT, 50KZx2 PO T, 130-017-02
JAPAN, 640-007-02 C D HO RN EQ , 10KC PO T, 130-037-02
ENG LAND, 640-007-03 M•1200/ M•1400i
ITALY, 640-007-04 ¼” JAC K, 400-118-00 ¼” INPUT JAC K, 400-214-00
AUSTRALIA, 640-007-05 WASHER, 710-019-00 ¼” JAC K WASHER, 710-002-00
SWITZERLAND, 640-007-06 SLO TTED NUT, 705-015-00 ¼” JAC K NUT, 705-003-00

STRAIN RELIEF M•1400 MALE XLR JAC K, 400-142-00


740-004-00 SPEAKO N, 400-138-00 FEMALE XLR JAC K, 400-141-00
SC REW, 700-055-00 XLR JAC K SC REWS,700-055-00
INTERNAL FUSES
RAIL FUSES; DP3T SWITC HES, 500-023-00
10A 5X20MM, 510-021-00 DPDT SWITC HES, 500-024-00
MAIN FUSE;
20A, 510-017-00
8A, 510-023-00

PARTS 15
M•1200/M•1400 SERVIC E MANUAL

C HASSIS ASSEMBLY

1 2

16 17 18

1 7 5

6 15

14
13

10 8

9 1
11
12

16 PARTS
VERSIO N 1.1

C HASSIS ASSEMBLY PARTS LIST


ITEM # PART # DESC RIPTIO N NO TES
1 700-028-02 SEMS 6-32X3/ 8 PHP BLKZC ALL SIDE PANEL SC REWS
2 550-221-00 TO P C O VER - M1200
3 700-041-04 MC H 6-32X3/ 8 FL 100DG BLK TO P C O VER TO C HASSIS
4 551-029-00 EXTR SC RN DSPLY BZL-M1200
4 551-029-10 EXTR SC RN DSPLY BZL-M1400
5 700-041-04 MC H 6-32X3/ 8 FL 100DG BLK MANIFO LD TO FAN
6 550-277-00 SC REEN MANIFO LD - M1400
7 550-223-20 SIDE RAIL LEFT - M1200
8 550-223-10 SIDE RAIL RIG HT - M1200
9 550-222-00 BTM C O VER - M1200
9 550-244-00 BO TTO M C O VER - M1400
10 080-023-20 PNT HANDLE ASSY LEFT
11 080-023-10 PNT HANDLE ASSY RIG HT
700-028-04 SEMS 6-32X3/ 4 PHP BLKZC HANDLE ASSY TO C HASSIS
700-041-04 MC H 6-32X3/ 8 FL 100DG BLK HEATSINK TO C HASSIS BO TTTO M

12 TRANSFO RMER / MO UNTING


600-016-00 XFMR M1200 120V
600-016-01 XFMR M1200 230V
600-016-02 XFMR M1200 100V
705-019-00 NUT HEX 5/ 16-18
710-017-00 WASH SPLTLC K 5/ 16 HEAVY
710-024-00 WASH FLAT 5/ 16 HARD (USS)
550-249-00 PLATE XFMR MTG - M1200
780-111-00 RUBBER PAD
700-059-00 HEX 5/ 16-18X3IN G D-5

13 550-247-00 SHIELD INPUT - M1200


14 780-042-00 INSUL MYLAR INPUT SHIELD
15 055-079-00 PC B ASSY INPUT 1200/ 1400
16 700-028-02 SEMS 6-32X3/ 8 PHP BLKZC INPUT PC B TO SHIELD
17 760-048-04 KNO B 9MM DARK G RAY
18 550-275-00 SPAC ER PLATE - AMPLIFIER
710-002-00 WASHER FO R ¼” JAC KS
705-003-00 NUT FO R ¼” JAC KS
700-055-00 MC H 4-24X3/ 8 PHP BLK HILO XLR JAC K SC REWS

055-080-00 PC B ASSY DISPLY 1200/ 1400


055-081-00 PC B ASSY MAIN - 1200
080-072-01 PC B ASSY MAIN - M1400
080-072-02 PC B ASSY MAIN - M1400i
700-028-02 SEMS 6-32X3/ 8 PHP BLKZC MAIN PC B TO C HASSIS EXC EPT FO R:
700-050-04 MC H 6-32X3/ 8 FIL PHL C LR ! USE THESE NEXT TO C APS !
700-011-00 MC H 4-40X1/ 4 BTNSKT BLKO X O UPTUT TERMINALS TO C HASSIS
710-019-00 WASH FIBRE BLK (W/ JAC K)
705-015-00 NUT SLO T NC KL
700-055-00 MC H 4-24X3/ 8 PHP BLK HILO

PARTS 17
M•1200/M•1400 SERVIC E MANUAL

HEATSINK ASSEMBLY

18 PARTS
VERSIO N 1.1

HEATSINK ASSEMBLY PARTS LIST


ITEM # PART # DESC RIPTIO N
1 551-032-00 EXTR FAB HEATSINK - M1200
2 410-003-00 INSL SILPAD K6 W/ ADHESIVE
3 055-081-00 PC B ASSY MAIN - 1200
3 080-072-01 PC B ASSY MAIN - M1400
3 080-072-02 PC B ASSY MAIN - M1400i
4 550-255-00 PIG G YBAC K C LIP
5 700-058-02 MC H 4-40X1/ 2 SKT C LRZC
6 710-020-00 WASH NO .4 C O MPRESSIO N
7 710-022-00 WASH FLAT NO .4 FENDER
8 550-224-00 BRAC KET SUBSINK - M1200
9 410-003-00 INSL SILPAD K6 W/ ADHESIVE
11 700-010-00 TF 6-32X1/ 4 PHP BLKZC
12 710-013-00 WASH FLAT NO .6 FIBRE
13 700-010-04 TF 6-32X3/ 8 PHP BLKZC
14 550-237-00 SPRING C LIP SUBSINK-M1200
15 700-028-02 SEMS 6-32X3/ 8 PHP BLKZC
16 550-225-00 HEATSINK C O WLING - M1200
17 700-010-00 TF 6-32X1/ 4 PHP BLKZC
18 770-006-00 FAN 80MM 24VDC -MEC HATRO NI
18 770-007-00 FAN 80MM 24VDC -PANASO NIC
19 550-219-00 BRKT FAN PS - SR40.8
20 700-047-04 MC H 10-32X3/ 8 FIL PHL C LR
21 700-028-02 SEMS 6-32X3/ 8 PHP BLKZC
22 400-083-00 2P .100X1 22G A END
24 700-058-02 MC H 4-40X1/ 2 SKT C LRZC
25 710-020-00 WASH NO .4 C O MPRESSIO N

PARTS 19
M•1200/M•1400 SERVIC E MANUAL

C O MPLETE PARTS LIST


040- C a b le s 500- Switc he s 640- AC Line C o rd s
055- Finishe d PC B Assys 510- Fuse s 700- Ha rd wa re
100- Po ts a nd Re sisto rs 550- C ha ssis Me ta l 760- Kno b s/ Pla stic
200- C a p a c ito rs 600- Tra nsfo rme rs 790- Misc ./ Pa c king
300- Se mic o nd uc to rs 601- Ind uc to rs 800- Printe d Ma te ria l
400- Ja c ks/ C o nne c to rs 610- Wire s a nd C a b le s

PART # DESC RIPTIO N PART # DESC RIPTIO N


040-033-02 RIB 28G A TRANS 20C 18IN 100-094-00 RES C F .125W 5% 75K O HM
040-033-03 RIB 28G A TRANS 20C 4IN 100-097-00 RES C F .125W 5% 100K O HM
040-117-02 RIB 28G TRNS 10C .10 11.5 100-109-00 RES C F .125W 5% 1M O HM
055-079-00 PC B ASSY INPUT 1200/ 1400 100-110-00 RES C F .125W 5% 360K O HM
055-080-00 PC B ASSY DISPLY 1200/ 1400 100-111-00 RES C F .125W 5% 390K O HM
055-081-00 PC B ASSY MAIN - 1200 105-277-00 RES MF .125W 1% 750 O HM
080-072-01 PC B ASSY MAIN - M1400 105-331-00 RES MF .125W 1% 2K49 O HM
080-072-02 PC B ASSY MAIN - M1400i 110-036-00 RES C F .25W 5% 300 O HM
080-034-00 PC B ASSY SO FT START – 120V 110-046-00 RES C F .25W 5% 750 O HM
080-034-01 PC B ASSY SO FT START – 240V 115-427-00 RES MF .25W 1% 24K9 O HM
080-023-10 PNT HANDLE ASSY RIG HT 121-097-00 RES MO 1W 5% 10K O HM
080-023-20 PNT HANDLE ASSY LEFT 123-009-00 RES MO 3W 5% .22 O HM
080-035-00 PWR SW HARNESS - AMP 123-033-00 RES MO 3W 5% 2.2 O HM
100-001-00 RES C F .125W 5% 10 O HM 123-056-00 RES MO 3W 5% 20 O HM
100-017-00 RES C F .125W 5% 47 O HM 123-071-00 RES MO 3W 5% 82 O HM
100-023-00 RES C F .125W 5% 82 O HM 123-085-00 RES MO 3W 5% 330 O HM
100-027-00 RES C F .125W 5% 120 O HM 123-109-00 RES MO 3W 5% 3.3K O HM
100-030-00 RES C F .125W 5% 160 O HM 123-124-00 RES MO 3W 5% 13K O HM
100-031-00 RES C F .125W 5% 180 O HM 125-020-00 RES WW 15W 5% 82 O HM C MNT
100-035-00 RES C F .125W 5% 300 O HM 130-017-02 PO T RTY 50KC 12MM DUAL TN
100-040-00 RES C F .125W 5% 430 O HM 130-036-00 PO T RTY 5KA 16MM DL DTNT
100-042-00 RES C F .125W 5% 510 O HM 130-037-02 PO T RTY 10KC 9MM TN
100-045-00 RES C F .125W 5% 680 O HM 130-038-00 PO T TRIM 500B HO RIZ
100-049-00 RES C F .125W 5% 1K O HM 140-025-00 RES TF SM .1W 5% 10 O HM
100-050-00 RES C F .125W 5% 1K1 O HM 140-057-00 RES TF SM .1W 5% 220 O HM
100-056-00 RES C F .125W 5% 2K O HM 140-060-00 RES TF SM .1W 5% 300 O HM
100-061-00 RES C F .125W 5% 3K3 O HM 140-065-00 RES TF SM .1W 5% 470 O HM
100-068-00 RES C F .125W 5% 6K2 O HM 140-068-00 RES TF SM .1W 5% 620 O HM
100-071-00 RES C F .125W 5% 8K2 O HM 140-073-00 RES TF SM .1W 5% 1K0 O HM
100-072-00 RES C F .125W 5% 9K1 O HM 140-076-00 RES TF SM .1W 5% 1K3 O HM
100-073-00 RES C F .125W 5% 10K O HM 140-078-00 RES TF SM .1W 5% 1K6 O HM
100-075-00 RES C F .125W 5% 12K O HM 140-080-00 RES TF SM .1W 5% 2K0 O HM
100-076-00 RES C F .125W 5% 13K O HM 140-081-00 RES TF SM .1W 5% 2K2 O HM
100-080-00 RES C F .125W 5% 20K O HM 140-083-00 RES TF SM .1W 5% 2K7 O HM
100-082-00 RES C F .125W 5% 24K O HM 140-087-00 RES TF SM .1W 5% 3K9 O HM
100-083-00 RES C F .125W 5% 27K O HM 140-089-00 RES TF SM .1W 5% 4K7 O HM
100-084-00 RES C F .125W 5% 30K O HM 140-092-00 RES TF SM .1W 5% 6K2 O HM
100-086-00 RES C F .125W 5% 36K O HM 140-094-00 RES TF SM .1W 5% 7K5 O HM
100-089-00 RES C F .125W 5% 47K O HM 140-097-00 RES TF SM .1W 5% 10K O HM
100-092-00 RES C F .125W 5% 62K O HM 140-106-00 RES TF SM .1W 5% 24K O HM
100-093-00 RES C F .125W 5% 68K O HM 140-108-00 RES TF SM .1W 5% 27K O HM

20 PARTS
VERSIO N 1.1

PART # DESC RIPTIO N PART # DESC RIPTIO N


140-111-00 RES TF SM .1W 5% 36K O HM 300-003-00 DIO SW DL4148 100V SM
140-115-00 RES TF SM .1W 5% 51K O HM 300-007-00 DIO SW 1SS244-SUB 1SS245
140-123-00 RES TF SM .1W 5% 100K O HM 301-006-00 THY 2N6507 400V
140-124-00 RES TF SM .1W 5% 120K O HM 301-007-00 DIO PWR DUAL FEP30 (D7)
140-139-00 RES TF SM .1W 5% 470K O HM 301-008-00 DIO PWR DUAL FEN30 (D8)
140-147-00 RES TF SM .1W 5% 1M O HM 301-009-00 DIO PWR 1N4004
145-318-00 RES MF SM .1W 1% 2K00 O HM 301-010-00 DIO PWR 1N5404 3A 400V
145-389-00 RES MF SM .1W 1% 10K0 O HM 301-014-00 DIO PWR 1N4007
145-397-00 RES MF SM .1W 1% 12K1 O HM 302-001-00 DIO ZEN 1N5261B 47V 500MW
145-406-00 RES MF SM .1W 1% 15K0 O HM 302-003-00 DIO ZEN 1N4745A 16V 1W
145-469-00 RES MF SM .1W 1% 68K1 O HM 304-001-00 LED RED T-1
145-478-00 RES MF SM .1W 1% 84K5 O HM 304-004-00 LED G REEN T-1
145-485-00 RES MF SM .1W 1% 100K O HM 310-002-00 XSTR PNP 2N4403
145-547-00 RES MF SM .1W 1% 442K O HM 310-007-00 XSTR NPN 2N4401
150-009-00 RES FUS .25W 5% 2.2 O HM 310-023-02 XSTR NPN 2SC 2362K TR
150-037-00 RES FUS .25W 5% 33 O HM 310-028-00 XSTR PNP 2SB940A PO WER
150-045-00 RES FUS .25W 5% 68 O HM 310-029-00 XSTR NPN 2SD1264A PO WER
200-001-02 PLY .012UF 10% 100V TR 310-032-02 XSTR PNP 2SA1016K TR
200-004-02 PLY .047UF 10% 100V TR 310-033-00 XSTR PNP MJL21193
200-007-02 PLY .01UF 10% 100V TR 310-034-00 XSTR NPN MJL21194
200-015-02 PLY .0047UF 10% 100V PEI 310-035-00 XSTR PNP 2SA1478
200-022-02 PLY .47UF 5% 50V TR 310-036-00 XSTR NPN 2SC 3788
200-023-00 PLY/ BX .001UF 20% 250V Y2 310-037-00 XSTR NPN MJE340 PO WER
200-024-00 PLY/ BX .01UF 20% 250V Y2 310-038-00 XSTR PNP MJE350
200-025-02 PLY/ BX .56UF 5% 63V TR 310-042-00 XSTR NPN MJE15032
200-036-00 PLY/ BX .1UF 10% 250V 310-043-00 XSTR PNP MJE15033
205-002-02 MIC A 270PF 5% 500V TR 311-002-00 XSTR PNP MMST4403 SM
210-001-02 C ER .01UF +80/ -20% 50V TR 320-004-00 O PAMP 4560F
210-010-02 C ER 47PF 5% 500V NPO TR 323-001-00 LM339 Q UAD C O MP
210-017-02 C ER 470PF 5% 500V Y5E TR 323-002-00 LM339D Q UAD C O MP SM
211-003-00 C ER .001UF 10% 50V AX 329-012-00 VTL5C 10 O PTO C O UPLER
211-009-00 C ER .1UF 20% 50V AX 329-014-00 LM35DZ PREC TEMP SENSO R
212-001-00 C ER .01UF 10% 50V X7R SM 400-059-00 TERM Q DISC .250 MALE PC MT
212-004-00 C ER 220PF 5% 50V NPO SM 400-060-00 FUSE C LIP PC MT 5MM DIA
212-009-00 C ER 47PF 5% 50V NPO SM 400-061-00 HDR 2P .100X1 STR LO C K
212-010-00 C ER .1 +80/ -20 25V Z5U SM 400-065-00 TERM Q DISC .250 F 18-22G A
220-001-02 LYT 22UF 20% 25V RAD TR 400-077-00 HDR 20P .1X2 STR LC K SHRD
220-002-02 LYT 47UF 20% 25V RAD TR 400-078-00 HDR 10P .1X2 STR LC K SHRD
220-004-02 LYT 470UF 20% 6.3V RAD TR 400-083-00 2P .100X1 22G A END
220-007-00 LYT 100UF 20% 100V RAD 400-118-00 JAC K 1/ 4 HO RIZ PC MNT MO NO
220-011-02 LYT 100UF 20% 25V RAD 400-119-00 TERM BANANA Q UAD HRZ PC MT
220-014-00 LYT 2.2UF 20% 50V RAD 400-129-00 FUSE C LIP .25 DIA PC MNT
220-025-00 LYT 1000UF 20% 35V RAD 400-133-00 HDR 6C K 11A/ 600V
220-027-02 LYT 10UF 20% 50V RAD TR 400-134-00 REC P 6C K 11A/ 600V
220-033-00 LYT 10000UF 20% 80V RAD 400-135-00 TERM 11A/ 600V F 18-20G A
220-034-00 LYT .47UF 20% 100V RAD 400-138-00 SPEAKO NS HO RIZ 4 C KT
220-035-00 LYT 12000UF 20% 80V RAD 400-141-00 XLR 3P F VERT A-SERIES
220-039-00 LYT 1000 20 25V RAD SMDIA 400-142-00 XLR 3P M VERT A-SERIES
220-040-00 LYT 10UF 20% 160V RAD 400-143-00 HDR 3P .100X1 STR
300-001-00 DIO SIG 1N4148 100V 500MW 400-171-00 HDR 2P .100X1 STR

PARTS 21
M•1200/M•1400 SERVIC E MANUAL

PART # DESC RIPTIO N PART # DESC RIPTIO N


400-172-00 TERM SO LDER-IN 18AWG 700-058-02 MC H 4-40X1/ 2 SKT C LRZC
400-173-00 TERM .25 Q KDS PC MT STABLE 700-059-00 HEX 5/ 16-18X3IN G D-5
400-210-00 TERM Q DISC .250 F 18-22G A 704-001-01 PEMNUT 6-32 .038 STL
400-214-00 JAC K 1/ 4 V PC MNT 1MM WASH 704-001-02 PEMNUT 6-32 .054 STL
410-003-00 INSL SILPAD K6 W/ ADHESIVE 704-007-01 PEMNUT 4-40X.060L SS FLSH
500-022-00 SW RC KR ILLUMINATED 704-023-03 STUD 6-32X.500 STL FLSH
500-023-00 SW SLIDE 4P3T MINI 705-001-00 KEPNUT 6-32
500-024-00 SW SLIDE DPDT MINI 705-003-00 NUT (SPLD W/ JAC K)
501-002-00 RELAY SPDT 30AMP 110VDC 705-013-00 NUT HEX M7 BLK
510-017-00 FUSE SB 20A 3AB 1/ 4X1-1/ 4 705-015-00 NUT SLO T NC KL SPLD W/ JAC K
510-021-00 FUSE FB 10A 5X20MM 250V 705-018-00 NUT HEX 5/ 16-18 (G D-5)
550-219-00 BRKT FAN PS - SR40.8 706-036-01 6-32X.188L STL PEM
550-221-00 TO P C O VER - M1200 706-036-03 STDF 6-32X.312L STL PEM
550-222-00 BTM C O VER - M1200 706-045-00 SPC R PVC .770 LED HI TEMP
550-223-10 SIDE RAIL RIG HT - M1200 710-002-00 WASHER (SPLD WITH JAC K)
550-223-20 SIDE RAIL LEFT - M1200 710-013-00 WASH FLAT NO .6 FIBRE
550-224-00 BRAC KET SUBSINK - M1200 710-017-00 WASH SPLTLC K 5/ 16 HEAVY
550-225-00 HEATSINK C O WLING - M1200 710-019-00 WASH FIBRE BLK (W/ JAC K)
550-237-00 SPRING C LIP SUBSINK-M1200 710-020-00 WASH NO .4 C O MPRESSIO N
550-244-00 BO TTO M C O VER - M1400 710-022-00 WASH FLAT NO .4 FENDER
550-247-00 SHIELD INPUT - M1200 710-023-00 WASH STAR M7 .020 THK
550-249-00 PLATE XFMR MTG - M1200 710-024-00 WASH FLAT 5/ 16 HARD (USS)
550-255-00 PIG G YBAC K C LIP 711-001-00 LUG NO .6 SO LDER STAR
550-275-00 SPAC ER PLATE - AMPLIFIER 712-020-00 BRKT ANG 6-32X.037THK STL
550-277-00 SC REEN MANIFO LD - M1400 712-021-01 RVT C L END .125X.062-.125
551-029-00 EXTR SC RN DSPLY BZL-M1200 740-004-00 STRAIN RELIEF HEYC O 1244
551-029-10 EXTR SC RN DSPLY BZL-M1400 760-048-04 KNO B 9MM DARK G RAY
551-032-00 EXTR FAB HEATSINK - M1200 760-061-00 KNO B VO LUME M1200
553-002-01 C RS 18G A 36 X 120 770-006-00 FAN 80MM 24VDC -MEC HATRO NI
553-002-03 C RS 18G A 48 X 120 770-007-00 FAN 80MM 24VDC -PANASO NIC
553-006-03 EG 18G A 48 X 120 780-042-00 INSUL MYLAR INPUT SHIELD
553-007-03 AL .063 48 X 120 780-114-00 RUBBER WASHER - THIN
553-010-03 EG 20G A 48 X 120 790-002-00 BAG PO LY 12 X 18 2MIL
553-015-03 AL .125 1100 H14 48 X 120 790-016-00 BAG PO LY 24X30 4MIL-M1200
553-017-01 SS .048 17-7 36 X 120 800-066-00 BO X M1200
600-016-00 XFMR M1200 120V 800-069-00 BO X M1400
601-006-00 INDUC TO R AIR C O IL 1UH 810-056-00 INST TO P/ BO TTO M - AMP
611-029-02 WIR 18G A 1007 BLK 5IN ST2 820-062-00 O WN MNL - M1200/ M1400
611-038-00 WR 18G 1010 G N/ YL 4IN ST2 820-062-10 O WN MNL – M1400i
660-005-00 22G A JUMPER WIRE 830-016-00 REG & WARR C ARD FR SERIES
700-005-00 SEMS 8-32X1/ 2 PHP BLKZC
700-010-00 TF 6-32X1/ 4 PHP BLKZC
700-010-04 TF 6-32X3/ 8 PHP BLKZC
700-011-00 MC H 4-40X1/ 4 BTNSKT BLKO X
700-028-02 SEMS 6-32X3/ 8 PHP BLKZC
700-028-04 SEMS 6-32X3/ 4 PHP BLKZC
700-041-04 MC H 6-32X3/ 8 FL 100DG BLK
700-047-04 MC H 10-32X3/ 8 FIL PHL C LR
700-050-04 MC H 6-32X3/ 8 FIL PHL C LR
700-055-00 MC H 4-24X3/ 8 PHP BLK HILO

22 PARTS
T H E M I X ER FI X ER • M ACK I E DESI GN S SERV I CE

N EWS
FR Se rie s Fuse Upg ra de

Mo d e l: FR Se rie s M1200/ 1400, 110V o nly

Se ria l # : M1200 p rio r to SN# AF12626 Effe c tive 4/ 28/ 97


M1400 p rio r to SN# AH12657

Pro b le m : O rig ina l fuse (15A) ra te d to o lo w. Turn o n inrush c urre nt c a use s fuse to
o p e n.

So lutio n: Re p la c e the ma in (F1) fuse with a 20A 250V slo w b lo w fuse .

Atte ntio n!: Sinc e yo u will b e wo rking d ire c tly with the AC p o we r line , g re at c are sho uld b e
take n in all asp e c ts o f the installatio n. Po we r sho uld b e d isc o nne c te d fro m the unit p rio r
to the insta lla tio n p ro c e ss.

F1=20A
250V
Slow Blow

Top
View

FR Se rie s Fuse up g ra d e BC 6/ 20/ 97


T H E M I X ER FI X ER • M ACK I E DESI GN S SERV I CE

N EWS
FR Tywra p Mo d

Mo d e l: FR Se rie s M1200/ 1400

Se ria l # : AFXXXXX to AFXXXXX Effe c tive 5/ 8/ 97

Pro b le m : The p rima ry a nd se c o nd a ry wire s g e t p inc he d b e twe e n the to p c o ve r a nd


the fa n shro ud .

So lutio n: Insta ll a 7 ½” tywra p thro ug h the fa n shro ud tunne ls. (740-016-00 15 1/ 16”
tywra p , c ut to 7 ½” )

7 ½” 7 ½”
Tywra p
15 1/ 16”

7 ½” tywa rp

Fa n Fro nt Vie w

To p Vie w

Top Transformer secondary


View wires

Transformer primary
wires

FR Tyw ra p Mo d BC 4/ 28/ 97
FR series Amplifier ribbon replacement instructions (NEW! IMPROVED! July 2000)*
Models affected: FR series M1200, M1400, M1400i
M1200: All models. M1400i: Before Serial # DA20889 and all models with “AM” prefix.
M1400 and 230v versions: Before Serial # DB12700 and all models with “AH” prefix.
Add this as part of your normal repair procedures.
Note: This bulletin replaces all previous ribbon bulletins.
Symptom:
Ch.1 or 2 output signal intermittently fades out, or cuts out completely and/or the DC supply rail fuses blow.
Possible Cause:
The two ribbon cables from the input board may be defective
Solution:
*Replace the input ribbon cables with an improved type in all of the above models, (including any which
have had the previous ribbon bulletin completed).

Safety Warning:
Caution! These instructions are for use by qualified personnel only. To avoid electric shock, do not
perform any servicing unless you are qualified to do so. Refer all service to qualified personnel.
Tools Required:
Phillips screwdriver, Torx and Allen drivers, needle nose pliers, safety glasses.
Parts Required:
040-359-00 Ribbon cable, 28GA, 20 Pin, Length 4.25”, PLZD Quantity = 1
040-360-00 Ribbon cable, 28GA, 20 Pin, Length 18”, PLZD Quantity = 1
400-077-00 20 Pin Headers Quantity = 2

Procedure:
1. Remove all cords (including the power cable and speaker outputs) from the amplifier.
2. Take off the top cover and inspect the ribbon cables. If they are not marked 040-359-00 or
040-360-00 then proceed as follows:
Remove the input board:
3. Undo the XLR screws, TRS nuts, and pull out the four pot knobs.
4. Disconnect the short ribbon cable from the amp board, and the long cable from the front panel
display board. On later amplifiers, you will have to remove the front display board first.
5. Disconnect the black ground wire from the amp board.
6. Undo the four screws on the right side of the chassis. This will give enough room to pull out the input
board. Catch the two metal XLR plates before they fall inside (not present on later amplifiers).
Input
board
Ribbon Ribbon
XLR plates

Continued....

Ribbon modification SSE July 2000


Ribbon mod.pdf, page 1 of 2
THE MACKIE FIXER • MACKIE DESIGNS SERVICE NEWS

Procedure continued.

Input board work:


If the two ribbon cables are soldered to the input board, follow steps 7 to 11. If not, then go to step 12.
7. Remove the metal shield plate and insulator sheet from the back of the input board.
8. Carefully unsolder the ribbon cable headers from J16 and J11.
Discard part# 040-033-03, 4 inch ribbon cable.
Discard part# 040-033-02, 18 inch ribbon cable.
9. Solder two new headers (#400-077-00) to the input board, with the cutout side pointing towards
the center of the input board (i.e. downwards).
10. Replace the metal shield plate and insulator sheet onto the back of the input board.
11. Add part# 040-359-00, 4.25 inch ribbon cable to J11.
Add part# 040-360-00, 18 inch ribbon cable to J16.
Align each cable’s color stripe with the header’s pin 1.
Make sure both ribbons are fully inserted, then proceed to step 15.

If the two ribbon cables are not soldered to the board, follow steps 12 to 14.
12. Discard part# 040-062-00, 4.25 inch ribbon cable.
Discard part# 040-062-02, 18 inch ribbon cable. You may have to undo the display board screws
in order to remove it from J1.
13. Add part# 040-359-00, 4.25 inch ribbon cable to J11.
Add part# 040-360-00, 18 inch ribbon cable to J16.
Align each cable’s color stripe with the header’s pin 1.
Make sure both ribbons are fully inserted.
14. Refit the display board, once the long ribbon cable is securely attached to J1.
Putting the input board back in:
15. Add the two metal XLR plates (where fitted) and carefully fit the input board back in place. Put
the four pot knobs back after the board is in place.
16. It can be difficult getting the knobs back on through the chassis holes, but you can make it easier
by snipping off a bit of the plastic center ridge, as shown in the little knob diagram below.
17. Add and tighten all the nuts and screws, and the four chassis screws (removed in step 6).
18. Make sure that all ribbon cables are secure and that all ends are fully inserted.
19. Reconnect the black wire from the input board to the amp board.
20. Replace the top cover.
21/ Perform a complete specification and safety test before returning the unit to the customer.

Pin 1 Color Stripe

Input
board Headers
J11 J16
snip off

knob

Ribbon modification SSE July 2000


Ribbon mod.pdf, page 2 of 2
M•1200/ M•1400 INPUT PC B 055-079-00 REV-D

23
M•1200/ M•1400 INPUT PC B 055-079-00 REV-D

24
M•1200/ M•1400 DISPLAY PC B 055-080-00 REV-A

25
M•1200/ M•1400 DISPLAY PC B 055-080-00 REV-A

26
M•1200/ M•1400 MAIN PC B 055-081-00 REV-D

27
M•1200/ M•1400 MAIN PC B 055-081-00 REV-D

28
M•1200/ M•1400 MAIN PC B 055-081-00 REV-D

29
M•1200/ M•1400 MAIN PC B 055-081-00 REV-D

30
M•1200/ M•1400 SO FT START PC B 055-162-00 REV-A

31
M•1200/ M•1400 SO FT START PC B 055-162-00 REV-A

32
M•1400 / M•1400i / M•1200

SERVICE MANUAL

Version 1.2 1998 MACKIE DESIGNS, INC.


820-179-00
CAUTION AVIS
CAUTION AVIS
RISK OF ELECTRIC SHOCK
DO NOT OPEN
RISQUE DE CHOC ELECTRIQUE
NE PAS OUVRIR

CAUTION: TO REDUCE THE RISK OF ATTENTION: POUR EVITER LES


ELECTRIC SHOCK DO NOT REMOVE RISQUES DE CHOC ELECTRIQUE, NE
THE COVER PAS ENLEVER LE COUVERCLE. AUCUN
NO USER SERVICEABLE PARTS INSIDE ENTRETIEN DE PIECES INTERIEURES
REFER SERVICING TO QUALIFIED PAR L'USAGER. CONFIER L'ENTRETIEN
PERSONNEL AU PERSONNEL QUALIFIE.
WARNING: TO REDUCE THE RISK OF AVIS:POUR EVITER LES RISQUES
FIRE OR ELECTRIC SHOCK, DO NOT D'INCENDIE OU D'ELECTROCUTION,
EXPOSE THIS PRODUCT TO RAIN OR N'EXPOSEZ PAS CET ARTICLE A LA
MOISTURE PLUIE OU A L'HUMIDITE.
TO PREVENT ELECTRIC SHOCK, DO POUR PREVENIR LES CHOCS
NOT USE THIS POLARIZED PLUG WITH ELECTRIQUES NE PAS UTILISER CETTE
AN EXTENSION CORD, RECEPTACLE OR FICHE POLARISEE AVEC UN
OTHER OUTLET UNLESS THE BLADES PROLONGATEUR, UN PRISE DE
CAN BE FULLY INSERTED TO PREVENT COURANT OU UNE AUTRE SORTIE DE
BLADE EXPOSURE. COURANT, SAUF SI LES LAMES
PEUVENT ETRE INSEREES A FOND
SANS LAISSER AUCUNE PARTIE A
DECOUVERT.

The lig htning fla sh w ith a rro w hea d symb o l w ithin an


e quila te ra l tria ng le is inte nd e d to a le rt the use r to the
p re se nc e o f uninsula te d "d a ng ero us v o lta g e " w ithin the
p ro d uc t's e nc lo sure , tha t m a y b e o f suffic ie nt m a g nitud e to
c onstitud e a risk o f e le c tric sho c k to pe rso ns.

Le sym b o le é c la ir av e c po int de flé c he à l'inte rie ur d 'un


tria ng le é q uila té ra l e st utilisé p o ur a le rte r l'utilisa te ur d e la
p ré se nc e à l'inte rie ur d u c o ffre t d e "vlo ta g e d a ng e re ux" no n
iso le d 'a m p le ur suffisa nte p o ur c o nstitue r un risq ue
d 'é lé c tro c utio n.

The e xc la m a tio n p o int w ithin a n e q uila te ra l tria ng le


is inte nd e d to a le rt the use r to the p re se nc e o f
imp o rta nt o p e ra ting a nd m a inte na nc e (se rvic ing )
instruc tio ns in the lite ra ture a c c o m p a nying the
a pp lia nc e .

Le p o int d 'e xc la m a tio n à l'inté rie ur d 'un tria ng le d e


la p ré se nc e d 'instruc tio ns im p o rta nte s p o ur le
fo nc tio nne m e nt e t l'e ntre tie n ( se rvic e ) d a ns le livre t
d 'instruc io n a c c o m p a g na nt L'a p p a re il.
®

TABLE O F C O NTENTS
INTRO DUC TIO N............................................................. 2
SYSTEM O VERVIEW ....................................................... 3
SUMMARY O F FEATURES .....................................................................4
SPEC IFIC ATIO NS...................................................................................6

C IRC UIT THEO RY........................................................... 8


INPUT C IRC UITRY..................................................................................8
PO WER AMPLIFIER C IRC UITRY...........................................................8
PRO TEC TIO N C IRC UITS .......................................................................9
THERMAL MANAG EMENT..................................................................10

SERVIC E PRO C EDURES............................................... 11


REQ UIRED EQ UIPMENT LIST..............................................................11
TRO UBLESHO O TING TIPS - O UTPUT FAILURES................................12
TEST AND BIASING PRO C EDURE......................................................13

PARTS............................................................................ 15
Q UIC K PARTS ......................................................................................15
C HASSIS ASSEMBLY............................................................................16
HEATSINK ASSEMBLY..........................................................................18
C O MPLETE PARTS LIST........................................................................20

SC HEMATIC S / PC B LAYO UTS.................................... 23


INPUT PC B SC HEMATIC .....................................................................23
INPUT PC B LAYO UT............................................................................24
DISPLAY PC B SC HEMATIC ................................................................25
DISPLAY PC B LAYO UT........................................................................26
MAIN PC B SC HEMATIC S...................................................................27
MAIN PC B LAYO UT............................................................................30
SO FT START PC B SC HEMATIC ...........................................................31
SO FT START PC B LAYO UT...................................................................32
M•1200/M•1400 SERVIC E MANUAL

INTRO DUC TIO N


This ma nua l c o nta ins c o mp le te se rvic e info rma tio n fo r the M•1200, M•1400 a nd M•1400i
a ud io p o w e r a m p lifie rs. O p e ra ting instruc tio ns w ill b e to uc he d o n b rie fly. Fo r c o m p le te
o p e ra ting instruc tio ns re fe r to the o wne r’ s m a nua l.
The FR Se rie s M•1200 a nd M•1400 a re hig h p o we r a ud io a mp lifie rs d e sig ne d fo r
p ro fe ssio na l a p p lic a tio ns. The y fe a ture a ud io p hile q ua lity so und , e xc e lle nt sta b ility,
e xte nsive p ro te c tio n c irc uitry, a nd le g e nd a ry Ma c kie re lia b ility. Pa te nte d Fa st Re c o ve ry
c irc uitry a llo ws the M•1200/ M•1400 to re c o ve r fro m c lip p ing witho ut g e ne ra ting
und e sira b le a rtifa c ts.

SERVIC E O N THE M•1200/ M•1400 IS


TO BE PERFO RMED BY EXPERIENC ED
TEC HNIC IANS O NLY!

To se rvic e the M•1200/ M•1400, te c hnic ia ns sho uld b e fa milia r with o p -a mp s, d isc re te
a na lo g c irc uitry, a nd tro ub le sho o ting hig h p o w e r so lid sta te a m p lifie rs. Pre se nta tio n o f
this m a nua l d o e s no t c o nstitute e nd o rse m e nt o f q ua lific a tio ns b y Ma c kie De sig ns.

! SMD !
The M•1200/ M•1400 ma ke s e xte nsive
use o f surfa c e mo unt c o mp o ne nts.
Se rvic ing te c hnic ia ns sho uld ha ve the
to o ls a nd e xp e rie nc e to p e rfo rm
surfa c e mo unt re wo rk.

TEC HNIC AL SUPPO RT


Ma c kie De sig ns Te c hnic a l Sup p o rt De p a rtme nt is a va ila b le 8AM - 5PM PST, Mo nd a y -
Frid a y a t 1-800-258-6883 (o utsid e US c a ll 011-425-487-4333) Ple a se fe e l fre e to c a ll with
a ny q ue stio ns (Be tte r sa fe tha n so rry!).

DISC LAIMER
The info rm a tio n c o nta ine d in this m a nua l is p ro p rie ta ry to Ma c kie De sig ns, Inc . The
e ntire m a nua l is p ro te c te d und e r c o p yrig ht a nd m a y no t b e re p ro d uc e d b y a ny m e a ns
witho ut e xp re ss writte n p e rmissio n fro m Ma c kie De sig ns, Inc .

2 INTRO DUC TIO N


VERSIO N 1.1

SYSTEM O VERVIEW
This se c tio n p ro vid e s a q uic k summa ry o f the M•1200/ M•1400’ s ma jo r fe a ture s. It is no t
inte nd e d to ta ke the p la c e o f the o wne r’ s m a nua l. It is inc lud e d he re to he lp se rvic ing
te c hnic ia ns fa milia rize the mse lve s with the M•1200/ M•1400.

DIFFERENC ES BETWEEN THE M•1400, M•1400i AND M•1200


The M•1200 a nd M•1400 a re e le c tro nic a lly id e ntic a l p ro d uc ts with the fo llo wing
e xc e p tio ns:
1. The M•1400 ha s 12,000uF ma in filte r c a p s, whe re the M•1200 a nd M•1400i ha ve
10,000uF.
2. The M•1400 a nd M•1400i use a mo re p o we rful fa n tha n the M•1200.
3. The M•1400 ha s Sp e a ko n c o nne c to rs whe re the M•1200 a nd M•1400i ha ve ¼”
sp e a ke r o utp uts (b o th in a d d itio n to b ind ing p o sts).
The M•1200 wa s d isc o ntinue d in 1998 a nd re p la c e d b y the M•1400i.
Exp o rt M•1400’ s a lso ha ve a “ So ft Sta rt” c irc uit tha t is no t insta lle d o n Am e ric a n units.

FAST REC O VERY DESIG N


So lid sta te p o w e r a m p lifie rs ha ve a re p uta tio n fo r so und ing ha rsh w he n d rive n into
c lip p ing . The usua l e xp la na tio n is o d d ha rm o nic s g e ne ra te d b y ha rd c lip p ing , b ut In
fa c t m uc h o f the unp le a sa nt so und is c a use d b y la tc hing a nd p a ra sitic o sc illa tio ns tha t
o c c ur a s the a m p lifie r re c o ve rs fro m c lip p ing .

TYPIC AL AMPLIFIER MAC KIE FR SERIES

ARTIFACTS C AUSED BY
LATCHING AND PARASITIC
O SCILLATIO N

Ma c kie ’ s Fa st Re c o ve ry d e sig n re c o ve rs fro m c lip p ing q uic kly witho ut g e ne ra ting a ny


und e sira b le a rtifa c ts. This p e rfo rm a nc e is a c hie ve d b y two uniq ue d e sig n e le m e nts; the
Full Sym m e try Dua l Diffe re ntia l fro nt e nd p ro vid e s e xc e lle nt line a rity w hile m inim izing the
ne e d fo r ne g a tive fe e d b a c k, a nd the Ba ke r C la mp p re ve nts o utp ut/ d rive r d e vic e
sa tura tio n. Ho w the se c irc uits o p e ra te is c o ve re d in d e p th in the c irc uit the o ry se c tio n.

SYSTEM O VERVIEW 3
M•1200/M•1400 SERVIC E MANUAL

SUMMARY O F FEATURES

FRO NT PANEL

1. G AIN
De te nte d g a in c o ntro ls a d just the le ve l se nt to e a c h o utp ut se c tio n. The g a in struc ture
is d e sig ne d so tha t a +4d Bu (1.23V rm s) inp ut sig na l d rive s the a m p lifie r to full ra te d
p o we r into 4Ω.

2. METERS
The M•1200/ M•1400’ s me te rs ind ic a te the re la tive o utp ut le ve l o f the a mp lifie r
re fe re nc e d to full p o we r. The SIG (sig na l p re se nt) se nse s the inp ut p rio r to the g a in
c o ntro l.

3. PRO TEC T
The Pro te c t LEDs lig ht ind ic a ting the c ha nne l ha s b e e n m ute d fo r o ne o f the fo llo wing
re a so ns:
• 4 se c o nd turn o n d e la y
• O utp ut d e vic e s b e yo nd Sa fe O p e ra ting Are a (SO A), a lso lig hts SHO RT LED(s).
• He a tsink te mp e ra ture b e yo nd 80 d e g re e s C e lsius.

4. SHO RT
The Sho rt LEDs lig ht to sho w tha t the a m p lifie r ha s e ng a g e d p ro te c tio n d ue to a sho rt o r
lo w im p e d a nc e o n the o utp ut.

5. TEMP STATUS
The HO T LED lig hts to ind ic a te tha t the a m p lifie r ha s e ng a g e d p ro te c tio n d ue to
he a tsink te mp e ra ture o r p o we r tra nsfo rme r c o re te mp e ra ture .

6. PO WER SWITC H
This re m a rka b le d e vic e re q uire s ye a rs o f stud y to full c o m p re he nd .

FULL SYMMETRY DUAL DIFFERENTIAL HIGH CURRENT DESIGN PROFESSIONALPOWER AMPLIFIER

CH GAIN /dB GAIN /dB CH CH CH


1 2
1 18
3v
20
22
OL

- 3
O
L
-3 1
3
v
2
0 2
2 INTERNALSTATUS ON
2v 8 2 2
1 2 - 6 -6 16 24 v PROTECT
6 4
1 26 - 9 -9 14 2 SHORT
4 6
- 2 - 2 TEMP STATUS OFF
8 28 0 8 2
0 8
30 3 CH

1v 01v 1& 2
COL HOT
SENSITIVITY 1.23v (+4dBu) SIG SIG 1.23v (+4dBu) D POWER
SENSITIVIT
Y

1 2 1 3 4 5 6

4 SUMMARY O F FEATURES
VERSIO N 1.1

REAR PANEL

1. SPEAKER O UTPUTS
The M•1400 ha s Sp e a ko n c o nne c to rs whe re the M•1200 ha s ¼” sp e a ke r o utp uts. Bo th
m o d e ls ha ve b ind ing p o sts. Fo r b rid g e d m o no o p e ra tio n, the + o utp ut c o m e s fro m
c ha nne l o ne ’ s p o sitive te rm ina l a nd - fro m c ha nne l tw o ’ s p o sitive .

2. INPUT
The M•1200/ M•1400 ha s b o th XLR a nd ¼” TRS inp uts. The y a re e le c tric a lly id e ntic a l
(wire d in p a ra lle l). In b rid g e d m o no o r p a ra lle l m o no m o d e c ha nne l 2 inp ut is d isa b le d .

3. THRO UG H
Ye t a no the r ja c k w ire d in p a ra lle l w ith the Inp uts, the thro ug h ja c k p ro vid e s a
c o nve nie nt w a y to c ha in a m p lifie rs o r p a ss the sig na l to a ny o the r d e vic e .

4. LO W C UT FILTER
Swe e p s the b uilt in hig h p a ss filte r fro m 10Hz to 170Hz.

5. C O NSTANT DIREC TIVITY HO RN EQ / AIR EQ


Built in she lving EQ p ro vid e s hig h fre q ue nc y c o m p e nsa tio n w he n using c o nsta nt
d ire c tivity ho rns.

6. AMP MO DE
Thre e p o sitio n slid e switc h se le c ts STEREO , PARALLEL MO NO o r BRIDG E MO NO o p e ra tio n.
C ha nne l O ne ’ s inp ut sig na l is use d fo r PARALLEL MO NO a nd BRIDG E MO NO o p e ra tio n.
AMP MO DE a nd O UTPUT APPLIC ATIO N switc he s sho uld no t b e c ha ng e d while the unit is
o n.

7. O UTPUT APPLIC ATIO N


Pla c ing the thre e p o sitio n slid e sw itc h in its c e nte r p o sitio n d e fe a ts the b uilt in LIMITER fo r
b o th c ha nne ls. Se le c ting SUB WO O FER e ng a g e s the b uilt in lo w p a ss filte r. The
FREQ UENC Y switc h se le c ts b e twe e n 125Hz a nd 63Hz c uto ff fo r the lo w p a ss filte r. In SUB
WO O FER mo d e , inp uts 1 a nd 2 a re summe d re g a rd le ss o f AMP MO DE se tting .
(Re m e m b e r, hum a n he a ring is una b le to d isc e rn d ire c tio n a t fre q ue nc ie s whe re the
wa ve le nth is g re a te r tha n the d ista nc e b e twe e n yo ur e a rs, ~250Hz unle ss yo u ha ve a
g ro ssly la rg e he a d !)

4 2 6 2 4

CAUTION 1 CHANNEL / BRIDGE / MONO AMPMODE CHANNEL 2


LOW CUT INPUT INPUT LOW CUT
STEREO MONO BRIDGE FILTER
FILTER TYPICAL
BALANCED BALANCED
O O
TYPICAL UNBALAN
R CED TYPIC
35Hz AL
UNBAL
RANCED
(MONO BRIDGE) 35 Hz
1200W A TTS STAGE STAGE
MONITOR MONITOR
4 OHM LOAD MIN.
600 W A TTSCH MONO
BRIDGE 100Hz OUTPUTAPPLICATION 100Hz
2OHMSLOADMIN.
+ -
CH CH OFF 170Hz OFF 170Hz
FULL SUB

1 2 CONSTANTDIRECTIV ITY
RANGE

LIMITER (CH1 & CH2)


WOOFER

CONSTANTDIRECTIV ITY
+ + HORNEQ/AIR EQ
4.5 kHz STEREO
FREQUENCY
HORN EQ /AIR EQ
4.5k Hz
ON TYPICAL 125Hz ON

- -
120VAC 50/60 Hz 2k Hz 6k Hz ON OFF 63Hz 2k Hz 6k Hz
1500 WATTS AIR EQ OFF OFF AIR EQ
TYPICAL TYPICAL
SPEAKER OUTPUTS THRU THRU

1 5 3 7 3 5

SYSTEM O VERVIEW 5
M•1200/M•1400 SERVIC E MANUAL

SPEC IFIC ATIO NS


No te : Po we r ra ting s a re sp e c ifie d a t
C O NTINUO US AVERAG E O UTPUT 120VAC (U.S. a nd C a na d a ) a nd 240VAC
PO WER, BO TH C HANNELS DRIVEN: (Exp o rt) line vo lta g e s.
M•1200 The M•1200/ M•1400 p o w e r a m p lifie rs d ra w
la rg e a m o unts o f c urre nt fro m the AC line w ith
225 w a tts p e r c ha nne l into 8 o hm s fro m 20Hz to c o ntinuo us sine w a ve te sting . Ac c ura te
20kHz, w ith no m o re tha n 0.025% THD m e a sure m e nt o f p o w e r re q uire s a ste a d y a nd
400 w a tts p e r c ha nne l into 4 o hm s fro m 20Hz to sta b le AC sup p ly. This m e a ns the line
20kHz, w ith no m o re tha n 0.050% THD im p e d a nc e m ust b e ve ry lo w to insure tha t the
600 w a tts p e r c ha nne l into 2 o hm s fro m 20Hz to p e a k AC line vo lta g e d o e s no t sa g to le ss tha n
20kHz, w ith no m o re tha n 0.095% THD 97% o f its va lue .
If d riving hig hly re a c tive lo a d s, w e re c o m m e nd
Bridg e d m o no o pe ra tio n:
tha t the lim ite r c irc uit b e e ng a g e d .
800 w a tts into 8 o hm s fro m 20Hz to 20kHz, w ith
no m o re tha n 0.050% THD PO WER BANDWIDTH:
1200 w a tts into 4 o hm s fro m 20Hz to 20kHz, w ith 20Hz to 70kHz (+0, –3 d B)
no m o re tha n 0.095% THD
Ma ximum Po we r a t 1% THD: FREQ UENC Y RESPO NSE:
250 w a tts p e r c ha nne l into 8 o hm s 20Hz to 40kHz (+0, –1 d B)
425 w a tts p e r c ha nne l into 4 o hm s 10Hz to 70kHz (+0, –3 d B)
640 w a tts p e r c ha nne l into 2 o hm s
850 w a tts into 8 o hm s b rid g e d DISTO RTIO N:
1280 w a tts into 4 o hm s b rid g e d
THD, SMPTE IMD, TIM < 0.025% @ 8Ω
M•1400 / M•1400i < 0.050% @ 4Ω
250 w a tts p e r c ha nne l into 8 o hm s fro m 20Hz to < 0.150% @ 2Ω
20kHz, w ith no m o re tha n 0.012% THD
425 w a tts p e r c ha nne l into 4 o hm s fro m 20Hz to SIG NAL-TO -NO ISE RATIO :
20kHz, w ith no m o re tha n 0.025% THD > 107 d B b e lo w ra te d p o w e r into 4 o hm s
630 w a tts p e r c ha nne l into 2 o hm s fro m 20Hz to
20kHz, w ith no m o re tha n 0.050% THD C HANNEL SEPARATIO N:
Brid g e d m o no o p e ra tio n: > 80 d B @ 1kHz

850 w a tts into 8 o hm s fro m 20Hz to 20kHz, w ith


no m o re tha n 0.025% THD DAMPING FAC TO R:
1260 w a tts into 4 o hm s fro m 20Hz to 20kHz, w ith 350 m inim um
no m o re tha n 0.050% THD
INPUT IMPEDANC E:
Ma xim um Po we r a t 1% THD:
20k b a la nc e d b rid g ing
300 w a tts p e r c ha nne l into 8 o hm s
500 w a tts p e r c ha nne l into 4 o hm s
700 w a tts p e r c ha nne l into 2 o hm s INPUT SENSITIVITY:
1000 w a tts into 8 o hm s b rid g e d 1.23 vo lts (+4 d Bu) fo r ra te d p o w e r into 4 o hm s
1400 w a tts into 4 o hm s b rid g e d
G AIN:
30.25 d B (32.5V/ V)

MAXIMUM INPUT LEVEL:


9.75 vo lts (+22 d Bu)

6 SPEC IFIC ATIO NS


VERSIO N 1.1

RISE TIME: LIMITER SEC TIO N:


< 4.4µs C o m p le m e nta ry Po sitive a nd Ne g a tive Pe a k
De te c ting
SLEW RATE:
Vo lta g e Sle w Ra te > 50V/ µs INDIC ATO RS:
> 100V/ µs b rid g e d 6 m e te r LEDs p e r c ha nne l
C urre nt Sle w Ra te > 32A/ µs a t 2Ω SIG (Sig na l Pre se nt), –20, –9, –6, –3, O L
(O ve rlo a d )

C MRR: CH 1 & 2
PRO TEC T LEDs
> 40 d B, 20Hz to 20kHz
SHO RT LEDs
TEMP STATUS
LO AD ANG LE:
C O LD/ HO T LEDs
8(±jx) tim e ind e p e nd e nt a t 8 Ω
4(±jx) tim e d e p e nd e nt, T > 6 m in. a t 4 Ω
PO WER C O NSUMPTIO N:
2(1±jx) tim e d e p e nd e nt, T > 2 m in. a t 2 Ω
65 w a tts a t id le
900 w a tts w ith m usic a l p ro g ra m fully lo a d e d
TRANSIENT REC O VERY:
(2 o hm s p e r sid e , o r 4 o hm s b rid g e d )
< 1µs fo r 20 d B o ve rd rive @ 1kHz 550 w a tts w ith m usic a l p ro g ra m fully lo a d e d
(4 o hm s p e r sid e , o r 8 o hm s b rid g e d )
HIG H FREQ UENC Y O VERLO AD AND 850 w a tts a t full p o w e r into 8 o hm s
(c o ntinuo us sine w a ve )
LATC HING :
1500 w a tts a t full p o w e r into 4 o hm s
No la tc h up a t a ny fre q ue nc y o r le ve l. (c o ntinuo us sine w a ve )
2500 w a tts a t full p o w e r into 2 o hm s
HIG H FREQ UENC Y STABILITY: (c o ntinuo us sine w a ve )
Unc o nd itio na lly sta b le d riving a ny re a c tive o r
c a p a c itive lo a d . AC LINE PO WER:
US 120VAC , 60Hz
TURN O N DELAY: Euro p e 240VAC , 50/ 60Hz
3 se c o nd s Ja p a n 100VAC , 50/ 60Hz
Ko re a 220VAC , 60Hz

VARIABLE LO W-C UT FILTER:


AC DRO P-O UT VO LTAG E:
10Hz (O ff) to 170Hz, 2nd O rd e r Be sse l
At a p p ro xim a te ly 50% o f ra te d line vo lta g e

SUBWO O FER LO W-PASS FILTER:


PHYSIC AL:
Sw itc he d : 63Hz/ 125Hz, 3rd O rd e r Be sse l
He ig ht 3.5 inc he s (89m m )
Wid th 19.0 inc he s (483m m )
C O NSTANT DIREC TIVITY HIG H De p th 15.25 inc he s (387m m )
FREQ UENC Y BO O ST: O ve ra ll De p th 16.25 inc he s (413m m )
2kHz to 6kHz (+3 d B p o ints) Ha nd le De p th 1.25 inc he s (32m m )
6 d B/ o c ta ve hig h-fre q ue nc y she lving filte r, We ig ht 36 p o und s (16.3kg )
(she lving o c c urs a t a p p ro xim a te ly 30kHz)
Sinc e w e a re a lw a ys striving to m a ke o ur stuff
b e tte r a t Ma c kie De sig ns b y inc o rp o ra ting ne w
a nd im p ro ve d m a te ria ls, c o m p o ne nts, a nd
m a nufa c turing m e tho d s, w e re se rve the rig ht to
c ha ng e the se sp e c ific a tio ns a t a ny tim e
w itho ut no tic e .

SPEC IFIC ATIO NS 7


M•1200/M•1400 SERVIC E MANUAL

C IRC UIT THEO RY


Muc h o f the c irc uitry in the M•1200/ M•1400 is se lf e xp la na to ry fro m the sc he ma tic . This
se c tio n will e xp la in the uniq ue c irc uits a nd a rc hite c ture . Sa m p le s in this se c tio n will re fe r
to C ha nne l 1 (Le ft) fo r c irc uitry tha t is id e ntic a l o n b o th c ha nne ls.

INPUT C IRC UITRY


Re fe r to sc he ma tic o n p a g e 23.
The sig na l p a th b e g ins with the INPUT BO ARD. Fo llo wing C ha nne l 1’ s inp ut, sig na l is fe d
to a unity g a in d iffe re ntia l o p -a m p , U1A. The sig na l is ne xt se nt to U1B whic h se rve s a s
b o th HPF a nd C D ho rn EQ . If no t in SUBWO O FER m o d e , the sum m ing a m p (U2B) a nd
LPF’ s (U3A, U3B) a re b yp a sse d . The sig na l is se nt via J11 to the g a in c o ntro l o n the
DISPLAY BO ARD. Afte r the g a in c o ntro l, the sig na l is b uffe re d b y U7A, re turne d to the
INPUT BO ARD a nd ro ute d to the MAIN BO ARD via J16.
C ha nne l 2’ s inp ut sig na l p a th is e le c tric a lly id e ntic a l to C ha nne l 1’ s in STEREO m o d e . In
PARALLEL MO NO mo d e C ha nne l 2’ s inp ut sig na l is ig no re d a nd C ha nne l 1’ s inp ut is se nt
to C ha nne l 2’ s g a in c o ntro l via SW5A. Fo r BRIDG E MO NO o p e ra tio n, C ha nne l 1’ s inp ut
sig na l is inve rte d b y U2A a nd ro ute d to the MAIN BO ARD via SW5C .

PO WER AMPLIFIER C IRC UITRY


Re fe r to sc he ma tic o n p a g e 27.
The M•1200/ M•1400 use a c la ss AB trip le d a rling to n o utp ut w ith c o m p le m e nta ry o utp ut
d e vic e s. The m a in p o we r sup p ly is +/ - 80V, the re is a lso a +/ - 90V sup p ly fo r the fro nt
e nd c irc uitry. C ha nne ls a re m ute d fo r 4 se c o nd s o n p o we r up a s C 53 c ha rg e s via R203.
Muting is a c hie ve d b y turning o ff Q 73, re m o ving c urre nt so urc e s fo r the d iffe re ntia l p a irs.
(Wa it a minute ! PAIRS? Re a d o n…)
An im m e d ia te ly o b vio us d e p a rture fro m sta nd a rd d e sig ns is the Dua l Diffe re ntia ls a nd
Symme tric a l Vo lta g e Amp s. The re a so ning b e hind this fro nt e nd a rc hite c ture is
a c tua lly q uite sim p le . Tra nsisto rs tra nsfe r c ha ra c te ristic s a re no t e ntire ly line a r, so e ve n
the b e st c o nve ntio na l fro nt e nd d e sig n will intro d uc e so m e d isto rtio n. Mo st a m p lifie rs
use ne g a tive fe e d b a c k to re d uc e this p ro b le m (c re a ting a fe w mo re in the p ro c e ss).
Ma c kie FR Se rie s a mp lifie rs ta ke a d iffe re nt a p p ro a c h. By using two c o mp le me nta ry
“ m irro r im a g e ” fro nt e nd c irc uits a ny d isto rtio n c a use d b y no n-line a r tra nsisto r c urve s is
e ffe c tive ly c a nc e le d o ut in the b ia s string , witho ut fe e d b a c k!
Ano the r d e sig n fe a ture uniq ue to Ma c kie FR Se rie s Amp lifie rs is the Ba ke r C la mp . The
Ba ke r C la mp ha s two func tio ns; 1) Pre ve nt o utp ut/ d rive r tra nsisto rs sa tura ting , 2) Drive
the LIMITER LDR. Re fe rring to the le ft ma in a mp sc he ma tic , Q 27 is a c o mmo n b a se
a m p lifie r, it w ill turn o n if Q 31’ s c o lle c to r rise s m o re tha n tw o d io d e d ro p s a b o ve the
+80V sup p ly, p re ve nting it fro m rising furthe r. The re a re thre e d io d e d ro p s b e twe e n
Q 31’ s c o lle c to r a nd the b a se o f d rive r tra nsisto r Q 28 (D3, D2, Q 29Vb e ). Q 29 will ne ve r
se e a vo lta g e g re a te r tha n o ne d io d e d ro p b e lo w the +80V sup p ly, e ve n if the +80V
sup p ly fluc tua te s. Q 27 a lso d rive s the limite r LDR LED U2A. The ne g a tive sid e ha s the
sa m e c irc uit m irro re d .

8 C IRC UIT THEO RY


VERSIO N 1.1

PRO TEC TIO N C IRC UITS


Re fe r to sc he ma tic s o n p a g e s 27-29.
The M•1200/ M•1400 ha s two o utp ut p ro te c tio n c irc uits in a d d itio n to the ra il fuse s. The
first m ute s the a m p if the o utp ut d e vic e s a re lo a d e d b e yo nd the ir sa fe o p e ra ting a re a
(SO A). The se c o nd is a c ro wb a r c irc uit tha t e nsure s the ra il fuse s b lo w if the re is DC o n
the o utp ut.

SO A PRO TEC TIO N


The SO A p ro te c tio n c irc uit se nse s the vo lta g e d ro p a c ro ss the e mitte r re sisto rs muc h like
sta nd a rd VI c urre nt lim iting tra nsisto rs. Q 76 a nd Q 77 w ill turn o n if the e m itte r d ro p
e xc e e d s ~1V. If the y a re o n fo r lo ng e no ug h to c ha rg e C 38 (thro ug h R159), the SO A
p ro te c tio n c irc uit is a c tiva te d b y tra nsisto r switc he s Q 79 a nd Q 78.
If SO A d e te c tio n is trip p e d , the c ha nne l is m ute d b y d isc ha rg ing C 53 thro ug h R200 a nd
D65, fa n sp e e d is inc re a se d , a nd the “ SHO RT” LED lig hts.

DC C RO WBARS
The DC C ro wb a r c irc uit p ro te c ts sp e a ke rs in the e ve nt o f a n o utp ut fa ilure b y b lo wing
a ll ra il fuse s. SC Rs Q 21-24 a re use d to sho rt the +/ - 80V sup p ly sup p lie s to g ro und .
O utp ut sig na l fro m b o th sid e s is fe d thro ug h 100K re sisto rs R90, R89 to C 21, e sse ntia lly
fo rm ing a LPF. DC o n e ithe r o utp ut will trig g e r c o m p a ra to r U4A (p o sitive ) o r U4B
(ne g a tive ). The SC Rs a re the n fire d via d rive r tra nsisto rs Q 87, Q 88.

NO TE:
The LM339 c o m p a ra to r IC is use d e xte nsive ly in the
M•1200/ M•1400. It d iffe rs fro m a sta nd a rd o p -a mp
use d a s a c o m p a ra to r in tha t it ha s a n o p e n
c o lle c to r o utp ut. If the vo lta g e a t the inve rting inp ut
e xc e e d s the no n-inve rting , the LM339’ s o utp ut
switc he s to it’ s ne g a tive sup p ly. O the rwise , the
o utp ut is o p e n.

C IRC UIT THEO RY 9


M•1200/M•1400 SERVIC E MANUAL

THERMAL MANAG EMENT


Re fe r to sc he ma tic o n p a g e 29.
The M•1200/ M•1400 T-De sig n He a tsink/ Fa n c o o ls o utp ut d e vic e s e ve nly a nd d o e s no t
c o lle c t d ust o n the c irc uitry. The fa n o p e ra te s a t two sp e e d s, c o ntro lle d b y the
a mp lifie r. An LM35DZ mo unte d in the c e nte r o f the he a tsink p ro vid e s te mp e ra ture
info rm a tio n to the fa n c o ntro l a nd o ve rte m p c irc uits. The re is a lso a the rm a l b re a ke r in
the p o we r tra nsfo rme r.

FAN C O NTRO L C IRC UIT


The fa n vo lta g e c o m e s fro m a fe e d b a c k re g ula to r c irc uit fo rm e d b y Q 91 a nd Q 92. The
o utp ut vo lta g e is p ro g ra mme d b y the ra tio o f R209 to R211/ / R207 (/ / =p a ra lle l). Whe n
the unit is p o we re d up C 83 c ha rg e s thro ug h R241 p ro vid ing a 40 se c o nd d e la y b e fo re
the fa n sta rts. As C 83 c ha rg e s, U6D’ s o utp ut switc he s to -16V, sta rting the fa n. The n
U6A’ s o utp ut switc he s to o p e n, a llo wing U6B to inc re a se the fa n sp e e d , if trig g e re d . R240
a nd C 82 g ive the fa n e xtra vo lta g e whe n sta rting .
The fa n sp e e d is inc re a se d b y U6B a d d ing R211 in p a ra lle l with R207. (Q 91 wa nts it’ s
b a se a d io d e d ro p a b o ve g ro und , so Q 92 d o ub le s its Em itte r vo lta g e ). U6B is trig g e re d
b y U4D to inc re a se fa n sp e e d if;
• C ha nne l 1 SO A p ro te c tio n is a c tiva te d (U5C ), O R
• C ha nne l 2 SO A p ro te c tio n is a c tiva te d (U5D), O R
• The he a tsink is a b o ve 60 d e g C (U5B) AND p ro g ra m is d e te c te d (U4C ), O R
• The he a tsink te m p e ra ture is a b o ve 80 d e g C (U5A).
U6C a nd Q 89 a re use d to re se t the c irc uit o n p o we r d o wn. Und e r no rm a l o p e ra tio n
C 50 is c ha rg e d via D57, Ho ld ing Q 89 o ff. Whe n p o we r is re m o ve d C 50 d isc ha rg e s a nd
Q 89 switc he s o n a s the ra ils c o lla p se . Whe n the vo lta g e o n Q 89’ s c o lle c to r fa lls b e lo w
g ro und U6 switc he s to the ne g a tive ra il d isc ha rg ing C 82 a nd C 83.

THERMAL SHUTDO WN
Extre me he a tsink o r tra nsfo rme r c o re te mp e ra ture will a c tiva te O VERTEMP. U5A
a c tiva te s o ve rte mp if the LM35DZ d e te c ts he a tsink te mp e ra ture a b o ve 80 d e g C .
Fe e d b a c k re sisto r R137 re sc a le s U5A’ s vo lta g e re fe re nc e so tha t the he a tsink must c o o l
to b e lo w 50 d e g C b e fo re o ve rte m p is d e a c tiva te d . O ve rte m p c a n a lso b e a c tiva te d
b y the p o we r tra nsfo rm e r the rm a l b re a ke r (via Q 89). In e ithe r c a se , b o th c ha nne l a re
mute d via D69 a nd D66.

10 C IRC UIT THEO RY


VERSIO N 1.1

SERVIC E PRO C EDURES


MEC HANIC AL PRO C EDURES
The M•1200/ M•1400 d e sig n a llo ws e a sy re mo va l o f a ll c o mp o ne nts a nd a sse mb lie s.
Disa sse m b ly a nd re a sse m b ly sho uld b e se lf e vid e nt. This m a nua l ha s e xp lo d e d
d ia g ra m s in the p a rts se c tio n.
Se ve ra l im p o rta nt p o ints c o nc e rning the a sse m b ly:
• 4 o f the sc re ws tha t se c ure the to p c o ve r a lso ho ld the fro nt e xtrusio n (c urve d
p ie c e ) in p la c e . Whe n re m o ving the to p c o ve r, b e c a re ful tha t the fro nt e xtrusio n is
no t d ro p p e d .
• If the MAIN PC B is re mo ve d , b e sure the sma lle r he a d ma c hine sc re ws (750-050-04)
a re re p la c e d ne xt to the filte r c a p s. The la rg e r he a d ma c hine sc re ws c a n a rc to the
c a p a c ito r b o d y.
• Be sure a ll tyw ra p s a re re p la c e d a nd tha t no w ire s a re in d a ng e r o f b e ing p inc he d
in-b e twe e n the c o ve r a nd he a tsink.

REQ UIRED EQ UIPMENT LIST


• 30 MHz d ua l tra c e o sc illo sc o p e
• DMM (Must b e c a p a b le o f me a suring 8mV DC with a minimum o f 2 d ig its o f
a c c ura c y, a nd d o wn to .1Ω)
• Sine wa ve o sc illa to r / Func tio n g e ne ra to r (20Hz - 20KHz)
• 4 lo a d re sisto rs (8Ω with a minimum 500W p o we r ra ting )
• 10A / 120V Va ria c With AC vo ltm e te r a nd a d e fe a ta b le a mme te r (1 Amp full ra ng e )
o r wa ttme te r (300 Wa tts full ra ng e )
• 0.1uF 400V film c a p a c ito r insta lle d a c ro ss d ua l b a na na p lug
• 16 AWG sho rting jum p e r insta lle d a c ro ss d ua l b a na na p lug

REC O MMENDED EQ UIPMENT LIST (PERFO RMANC E VERIFIC ATIO N)


• Disto rtio n a na lyze r a nd lo w d isto rtio n o sc illa to r.
(C a p a b le o f re so lving d isto rtio n a s lo w a s 0.002% fro m 20Hz to 20KHz)
• 2500W AC p o we r so urc e .

SERVIC E PRO C EDURES 11


M•1200/M•1400 SERVIC E MANUAL

TRO UBLESHO O TING TIPS - O UTPUT FAILURES


Afte r a c a ta stro p hic fa ilure , it is like ly tha t the fo ur +/ -80V sup p ly fuse s will b e b lo wn.
Re p la c e fuse s a nd ve ry slo wly b ring up the Va ria c w hile m o nito ring line c o nsum p tio n. It
is like ly tha t sub sta ntia l line c urre nt will b e p ulle d d ue to sho rte d o utp ut p a rts. At the
sa me time , lo o k fo r DC o ffse t a t the o utp ut. O ffse t o f g re a te r tha n +/ - 2.8V will trig g e r
the p ro te c tio n c irc uits a nd re -b lo w the fo ur fuse s. Ke e p the o utp ut o ffse t b e lo w +/ - 2V,
o r te mp o ra rily d e fe a t the DC -o ffse t d e te c to r (Lift o ne sid e o f D56).
Re m o ve the m a in b o a rd fro m the unit a nd c he c k fo r sho rte d o utp ut tra nsisto rs. If o ne
b a d o utp ut is fo und , re p la c e a ll e ig ht in the c ha nne l. Whe n a n o utp ut d e vic e sho rts it
c a n p la c e hig h c urre nt stre sse s o n the o the r o utp ut p a rts. The se o utp ut p a rts c a n fa il
o ve r tim e . Sinc e lo ng te rm re lia b ility is p a ra m o unt, p le a se re p la c e a ll the o utp uts.
All e ig ht o f the 3W 0.22Ω e m itte r re sisto rs m ust b e ve rifie d fo r p ro p e r va lue . Any o ff-
to le ra nc e , o r o p e n p a rts, ne e d to b e re p la c e d . An o ff to le ra nc e (hig he r re sista nc e )
e m itte r re sisto r will p re ve nt it’ s re la te d o utp ut tra nsisto r fro m “ d o ing it’ s sha re ” a nd will
p la c e mo re stre ss o n it’ s ma te s in the o utp ut se c tio n. Also ve rify the 8 b a se d rive re sisto rs
(2.2Ω, 1/ 4W, fusib le ) a re a ll O K. Ve rify tha t the d rive rs a nd p re -d rive rs a re no t sho rte d . If
o ne d rive r is sho rte d re p la c e it’ s ma te . Do the sa me with the p re -d rive rs. Also c he c k a ll
the re sisto rs surro und ing the d rive rs a nd p re -d rive rs.
C he c k the VI limite rs a nd d e te c to rs. It is no t unc o mmo n to d a ma g e the se p a rts whe n
the a mp lifie r fa ils in a sp e c ta c ula r wa y! Lo o k fo r sho rts o n Q 76, Q 77, Q 94, Q 95, Q 83,
Q 84, Q 96, a nd Q 97. Ve rify p ro p e r va lue o n the re sisto rs tha t g o to the b a se s o f the se
d e vic e s. It is c ritic a l tha t the se se c tio ns a re wo rking c o rre c tly. Sho rte d tra nsisto rs c a n
c a use so m e o d d a sym m e tric a l c lip p ing p ro b le m s. O p e n p a rts will no t a llo w the c urre nt
lim iting to o p e ra te e ffe c tive ly. If p ro b le m s e xist in the se se c tio ns the a m p lifie r m ig ht fa il
into a sho rt, o r m ig ht c lip p re m a ture ly w he n lo a d e d to 2 Ω.
All o f the a b o ve tro ub le sho o ting (No t inc lud ing p a rt re p la c e m e nt) ta ke s p e rha p s 15 to
30 m inute s to d o . If yo u ta ke the tim e , a nd d o a ll tha t is ind ic a te d a b o ve , it w ill a llo w
99% o f the a m p lifie rs to c o m e up the first tim e ! Trying to hurry, a nd skip p ing wha t is
sug g e ste d , c a n le a d to a frustra ting a nd tim e c o nsum ing re p a ir.
Slo w ly b ring up the sup p ly a nd ve rify tha t line c o nsum p tio n isn’ t e xc e ssive a nd tha t the
o utp ut is c e nte re d (no DC o ffse t). It mig ht b e d e sira b le to d e fe a t the a mp lifie r muting
(C o nne c t U5-12, 13, & 14 to g e the r) te mp o ra rily so the a mp lifie rs a re a c tive e ve n whe n
the sup p lie s a re still ve ry lo w. If the a m p sta ys c e nte re d , ve rify tha t it will p a ss a nic e
c le a n sine wa ve . Re mo ve a ny te st jump e rs (I.E. DC -fa ult d e fe a t & muting d e fe a t) a nd
p ro c e e d to the “ Re lia b ility Ve rific a tio n” se c tio n.

12 SERVIC E PRO C EDURES


VERSIO N 1.1

BIAS AND TEST PRO C EDURE


Afte r the unit ha s b e e n re p a ire d , the fo llo wing sho uld b e d o ne to a ssure lo ng te rm
re lia b le o p e ra tio n. If a d isto rtio n a na lyze r is p re se nt, d isto rtio n sp e c ific a tio ns sho uld b e
ve rifie d .
1. Ad justs b ia s in b o th c ha nne ls (R1 & R51) fo r 8mV +/ - 0.3mV a t b ia s te st p o ints (J53 &
J54) a fte r unit ha s id le d fo r a fe w m inute s. With Full AC line vo lta g e a p p lie d to unit,
it will p ull a ro und 65W fro m the line (900mA a t 120V). Me a sure fo r DC o ffse t o n b o th
o utp ut c o nne c to rs. DC o ffse t sho uld b e le ss tha n +/ - 50mV.
2. Ap p ly a 1KHz sine w a ve to the inp uts a nd ve rify tha t the unlo a d e d o utp uts ha ve a
w a ve fo rm tha t is sym m e tric a l a nd und isto rte d . Drive the o utp uts into c lip p ing a nd
ve rify sym m e tric a l “ fla t-to p p ing ” o n the wa ve fo rm .
3. Re d uc e o utp ut le ve ls, insta ll the 0.1uF c a p a c ito r jum p e r fro m the o utp ut to g ro und
c o nne c tio ns, a nd ve rify tha t c lip p ing b e ha vio r is p ro p e r. Ve rify tha t no hig h
fre q ue nc y o sc illa tio n o c c urs ne a r a nd a t c lip p ing (p a ra sitic o sc illa tio n).
4. Re m o ve c a p a c itive lo a d ing a nd m inim ize sine o utp ut. Ve rify a nd re -a d just b ia s if
re q uire d . No te tha t the b ia s w ill no t d rift a p p re c ia b ly in a unit tha t is func tio ning
p ro p e rly.
5. C o nne c t the a m p lifie r d ire c tly to the AC line a nd c o nne c t a n 8Ω d um m y lo a d to
b o th c ha nne ls. Bring sine w a ve le ve l up o n b o th c ha nne ls a nd ve rify sym m e tric a l
c lip p ing . The o utp ut will c lip so me whe re b e twe e n 120V - 140V p k/ p k d e p e nd ing o n
ho w stiff the line is. C lip p ing sho uld b e a s d e sc rib e d a b o ve . Ad d the 0.1uF
c a p a c itive lo a d ing a nd ve rify c lip p ing is still w e ll b e ha ve d .
6. Ind ivid ua lly lo a d C ha nne l 1 a nd C ha nne l 2 w ith 2 Ω. C lip p ing sho uld b e
symme tric a l, we ll b e ha ve d , a nd o c c ur so me whe re a ro und 80V - 100V p k/ p k. Ve rify
tha t c lip p ing is w e ll b e ha ve d a fte r a d d ing the 0.1uF c a p a c itive lo a d ing .
7. Re d uc e o utp ut le ve l to 20V p k/ p k a nd sho rt first c ha nne l o ne a nd the n c ha nne l
two . The fro nt p a ne l “ sho rt” a nd “ p ro te c t” LEDs sho uld fla sh o n the re sp e c tive
c ha nne ls.
8. Pla c e a m p lifie r in b rid g e m o d e a nd c o nne c t 4 Ω lo a d ing to b rid g e o utp uts (a c ro ss
b o th “ +” o utp ut b ind ing p o sts). Slip so m e c a rd sto c k b e twe e n the he a tsink-o utle ts
a nd c ha ssis sid e s. Mo nito r o ne o f the o utp uts a nd a d just fo r a 20V p k/ p k sig na l.
Sho rt a c ro ss b o th o utp uts a nd ve rify tha t a ll fo ur ‘ Sho rt” a nd “ Pro te c t” LEDs lig ht a nd
the a mp lifie r mute s.
9. Re m o ve sho rt, m o nito r o ne o f the o utp uts, a nd a d just fo r a 60V p k/ p k sine o utp ut
(450W o f o utp ut p o we r b rid g e d ). Afte r a fe w minute s the fa n will b e g in running fa st
(he a tsink a t 60°C ) a nd a sho rt tim e la te r the a m p lifie r will m ute (he a tsink a t 80°C ).
The “ Ho t” a nd “ p ro te c t” LEDs will c o me o n. Re mo ve c a rd sto c k a nd a fte r a fe w
m inute s the a m p lifie r will c o m e o ut o f m ute m o d e a nd the “ c o ld ” LED will re turn.

10. Disc o nne c t lo a d ing a nd re m o ve d rive . Re c o nne c t a m p lifie r to Va ria c a nd c o nfirm


tha t the id le c o nsump tio n is ro ug hly 65W o r 900mA, a s b e fo re . C o nne c t the
a m p lifie r to sp e a ke rs a nd ve rify tha t it so und s O K with m usic .

SERVIC E PRO C EDURES 13


M•1200/M•1400 SERVIC E MANUAL

(THIS PAG E UNINTENTIO NALLY LEFT BLANK), THO SE RESPO NSIBLE HAVE BEEN PUT TO THE SWO RD

14 SERVIC E PRO C EDURES


VERSIO N 1.1

PARTS
Q UIC K PARTS

FRO NT PANEL

FULL SYMMETRY DUAL DIFFERENTIAL HIGH CURRENT DESIGN PROFESSIONALPOWER AMPLIFIER

CH GAIN /dB GAIN /dB CH CH CH


1 2
1 18
3v
20
22
OL

- 3
O
L
-3 1
3
v
2
0 2
2 INTERNALSTATUS ON
2v 8 2 2
1 2 - 6 -6 16 24 v PROTECT
6 4
1 26 - 9 -9 14 2 SHORT
4 6
- 2 - 2 TEMP STATUS OFF
8 28 0 8 2
0 8
30 3 CH
1v 01v 1& 2
COL HOT
SENSITIVITY 1.23v (+4dBu) SIG SIG 1.23v (+4dBu) D POWER
SENSITIVIT
Y

HANDLE ASSEMBLYS G AIN C O NTRO LS ALL LEDS PO WER SWITC H


RIG HT, 080-023-10 5KL PO T, 130-036-00 RED T-1, 304-001-00 500-022-00
LEFT, 080-023-20 KNO B, 760-061-00 G REEN T-1, 304-004-00
SC REW(TO C HASSIS),700-028-04 NUT, 705-013-00
STAR WASHER, 710-023-00

REAR PANEL

CAUTION 1 CHANNEL / BRIDGE / MONO AMPMODE CHANNEL


2
LOW CUT
INPUT INPUT LOW CUT
STEREO MONO BRIDGE FILTER
FILTER TYPICAL
BALANCED BALANCED
O O
TYPICAL UNBALAN
R CED TYPIC
35Hz AL
UNBAL
RANCED
(MONO BRIDGE) 35 Hz
1200W A TTS STAGE STAGE
MONITOR MONITOR
4 OHM LOAD MIN.
600 W A TTSCH MONO
BRIDGE 100Hz OUTPUTAPPLICATION 100Hz
2OHMSLOADMIN. + -
CH CH OFF 170Hz OFF 170Hz
FULL SUB

1 2 CONSTANTDIRECTIV ITY
RANGE

LIMITER (CH1 & CH2)


WOOFER

CONSTANTDIRECTIV ITY
+ + HORNEQ/AIR EQ
4.5 kHz STEREO
FREQUENCY
HORN EQ /AIR EQ
4.5k Hz
ON TYPICAL 125Hz ON

- -
120VAC 50/60 Hz 2k Hz 6k Hz ON OFF 63Hz 2k Hz 6k Hz
1500 WATTS AIR EQ OFF OFF AIR EQ
TYPICAL TYPICAL
SPEAKER OUTPUTS THRU THRU

AC LINE C O RD SPEAKER O UTPUTS INPUT SEC TIO N


US, 640-006-00 BINDING PO STS, 400-119-00 ALL KNO BS, 760-048-04
EURO PE, 640-007-01 BINDING PO ST SC REW, 700-011-00 LO W C UT, 50KZx2 PO T, 130-017-02
JAPAN, 640-007-02 C D HO RN EQ , 10KC PO T, 130-037-02
ENG LAND, 640-007-03 M•1200/ M•1400i
ITALY, 640-007-04 ¼” JAC K, 400-118-00 ¼” INPUT JAC K, 400-214-00
AUSTRALIA, 640-007-05 WASHER, 710-019-00 ¼” JAC K WASHER, 710-002-00
SWITZERLAND, 640-007-06 SLO TTED NUT, 705-015-00 ¼” JAC K NUT, 705-003-00

STRAIN RELIEF M•1400 MALE XLR JAC K, 400-142-00


740-004-00 SPEAKO N, 400-138-00 FEMALE XLR JAC K, 400-141-00
SC REW, 700-055-00 XLR JAC K SC REWS,700-055-00
INTERNAL FUSES
RAIL FUSES; DP3T SWITC HES, 500-023-00
10A 5X20MM, 510-021-00 DPDT SWITC HES, 500-024-00
MAIN FUSE;
20A, 510-017-00
8A, 510-023-00

PARTS 15
M•1200/M•1400 SERVIC E MANUAL

C HASSIS ASSEMBLY

1 2

16 17 18

1 7 5

6 15

14
13

10 8

9 1
11
12

16 PARTS
VERSIO N 1.1

C HASSIS ASSEMBLY PARTS LIST


ITEM # PART # DESC RIPTIO N NO TES
1 700-028-02 SEMS 6-32X3/ 8 PHP BLKZC ALL SIDE PANEL SC REWS
2 550-221-00 TO P C O VER - M1200
3 700-041-04 MC H 6-32X3/ 8 FL 100DG BLK TO P C O VER TO C HASSIS
4 551-029-00 EXTR SC RN DSPLY BZL-M1200
4 551-029-10 EXTR SC RN DSPLY BZL-M1400
5 700-041-04 MC H 6-32X3/ 8 FL 100DG BLK MANIFO LD TO FAN
6 550-277-00 SC REEN MANIFO LD - M1400
7 550-223-20 SIDE RAIL LEFT - M1200
8 550-223-10 SIDE RAIL RIG HT - M1200
9 550-222-00 BTM C O VER - M1200
9 550-244-00 BO TTO M C O VER - M1400
10 080-023-20 PNT HANDLE ASSY LEFT
11 080-023-10 PNT HANDLE ASSY RIG HT
700-028-04 SEMS 6-32X3/ 4 PHP BLKZC HANDLE ASSY TO C HASSIS
700-041-04 MC H 6-32X3/ 8 FL 100DG BLK HEATSINK TO C HASSIS BO TTTO M

12 TRANSFO RMER / MO UNTING


600-016-00 XFMR M1200 120V
600-016-01 XFMR M1200 230V
600-016-02 XFMR M1200 100V
705-019-00 NUT HEX 5/ 16-18
710-017-00 WASH SPLTLC K 5/ 16 HEAVY
710-024-00 WASH FLAT 5/ 16 HARD (USS)
550-249-00 PLATE XFMR MTG - M1200
780-111-00 RUBBER PAD
700-059-00 HEX 5/ 16-18X3IN G D-5

13 550-247-00 SHIELD INPUT - M1200


14 780-042-00 INSUL MYLAR INPUT SHIELD
15 055-079-00 PC B ASSY INPUT 1200/ 1400
16 700-028-02 SEMS 6-32X3/ 8 PHP BLKZC INPUT PC B TO SHIELD
17 760-048-04 KNO B 9MM DARK G RAY
18 550-275-00 SPAC ER PLATE - AMPLIFIER
710-002-00 WASHER FO R ¼” JAC KS
705-003-00 NUT FO R ¼” JAC KS
700-055-00 MC H 4-24X3/ 8 PHP BLK HILO XLR JAC K SC REWS

055-080-00 PC B ASSY DISPLY 1200/ 1400


055-081-00 PC B ASSY MAIN - 1200
080-072-01 PC B ASSY MAIN - M1400
080-072-02 PC B ASSY MAIN - M1400i
700-028-02 SEMS 6-32X3/ 8 PHP BLKZC MAIN PC B TO C HASSIS EXC EPT FO R:
700-050-04 MC H 6-32X3/ 8 FIL PHL C LR ! USE THESE NEXT TO C APS !
700-011-00 MC H 4-40X1/ 4 BTNSKT BLKO X O UPTUT TERMINALS TO C HASSIS
710-019-00 WASH FIBRE BLK (W/ JAC K)
705-015-00 NUT SLO T NC KL
700-055-00 MC H 4-24X3/ 8 PHP BLK HILO

PARTS 17
M•1200/M•1400 SERVIC E MANUAL

HEATSINK ASSEMBLY

18 PARTS
VERSIO N 1.1

HEATSINK ASSEMBLY PARTS LIST


ITEM # PART # DESC RIPTIO N
1 551-032-00 EXTR FAB HEATSINK - M1200
2 410-003-00 INSL SILPAD K6 W/ ADHESIVE
3 055-081-00 PC B ASSY MAIN - 1200
3 080-072-01 PC B ASSY MAIN - M1400
3 080-072-02 PC B ASSY MAIN - M1400i
4 550-255-00 PIG G YBAC K C LIP
5 700-058-02 MC H 4-40X1/ 2 SKT C LRZC
6 710-020-00 WASH NO .4 C O MPRESSIO N
7 710-022-00 WASH FLAT NO .4 FENDER
8 550-224-00 BRAC KET SUBSINK - M1200
9 410-003-00 INSL SILPAD K6 W/ ADHESIVE
11 700-010-00 TF 6-32X1/ 4 PHP BLKZC
12 710-013-00 WASH FLAT NO .6 FIBRE
13 700-010-04 TF 6-32X3/ 8 PHP BLKZC
14 550-237-00 SPRING C LIP SUBSINK-M1200
15 700-028-02 SEMS 6-32X3/ 8 PHP BLKZC
16 550-225-00 HEATSINK C O WLING - M1200
17 700-010-00 TF 6-32X1/ 4 PHP BLKZC
18 770-006-00 FAN 80MM 24VDC -MEC HATRO NI
18 770-007-00 FAN 80MM 24VDC -PANASO NIC
19 550-219-00 BRKT FAN PS - SR40.8
20 700-047-04 MC H 10-32X3/ 8 FIL PHL C LR
21 700-028-02 SEMS 6-32X3/ 8 PHP BLKZC
22 400-083-00 2P .100X1 22G A END
24 700-058-02 MC H 4-40X1/ 2 SKT C LRZC
25 710-020-00 WASH NO .4 C O MPRESSIO N

PARTS 19
M•1200/M•1400 SERVIC E MANUAL

C O MPLETE PARTS LIST


040- C a b le s 500- Switc he s 640- AC Line C o rd s
055- Finishe d PC B Assys 510- Fuse s 700- Ha rd wa re
100- Po ts a nd Re sisto rs 550- C ha ssis Me ta l 760- Kno b s/ Pla stic
200- C a p a c ito rs 600- Tra nsfo rme rs 790- Misc ./ Pa c king
300- Se mic o nd uc to rs 601- Ind uc to rs 800- Printe d Ma te ria l
400- Ja c ks/ C o nne c to rs 610- Wire s a nd C a b le s

PART # DESC RIPTIO N PART # DESC RIPTIO N


040-033-02 RIB 28G A TRANS 20C 18IN 100-094-00 RES C F .125W 5% 75K O HM
040-033-03 RIB 28G A TRANS 20C 4IN 100-097-00 RES C F .125W 5% 100K O HM
040-117-02 RIB 28G TRNS 10C .10 11.5 100-109-00 RES C F .125W 5% 1M O HM
055-079-00 PC B ASSY INPUT 1200/ 1400 100-110-00 RES C F .125W 5% 360K O HM
055-080-00 PC B ASSY DISPLY 1200/ 1400 100-111-00 RES C F .125W 5% 390K O HM
055-081-00 PC B ASSY MAIN - 1200 105-277-00 RES MF .125W 1% 750 O HM
080-072-01 PC B ASSY MAIN - M1400 105-331-00 RES MF .125W 1% 2K49 O HM
080-072-02 PC B ASSY MAIN - M1400i 110-036-00 RES C F .25W 5% 300 O HM
080-034-00 PC B ASSY SO FT START – 120V 110-046-00 RES C F .25W 5% 750 O HM
080-034-01 PC B ASSY SO FT START – 240V 115-427-00 RES MF .25W 1% 24K9 O HM
080-023-10 PNT HANDLE ASSY RIG HT 121-097-00 RES MO 1W 5% 10K O HM
080-023-20 PNT HANDLE ASSY LEFT 123-009-00 RES MO 3W 5% .22 O HM
080-035-00 PWR SW HARNESS - AMP 123-033-00 RES MO 3W 5% 2.2 O HM
100-001-00 RES C F .125W 5% 10 O HM 123-056-00 RES MO 3W 5% 20 O HM
100-017-00 RES C F .125W 5% 47 O HM 123-071-00 RES MO 3W 5% 82 O HM
100-023-00 RES C F .125W 5% 82 O HM 123-085-00 RES MO 3W 5% 330 O HM
100-027-00 RES C F .125W 5% 120 O HM 123-109-00 RES MO 3W 5% 3.3K O HM
100-030-00 RES C F .125W 5% 160 O HM 123-124-00 RES MO 3W 5% 13K O HM
100-031-00 RES C F .125W 5% 180 O HM 125-020-00 RES WW 15W 5% 82 O HM C MNT
100-035-00 RES C F .125W 5% 300 O HM 130-017-02 PO T RTY 50KC 12MM DUAL TN
100-040-00 RES C F .125W 5% 430 O HM 130-036-00 PO T RTY 5KA 16MM DL DTNT
100-042-00 RES C F .125W 5% 510 O HM 130-037-02 PO T RTY 10KC 9MM TN
100-045-00 RES C F .125W 5% 680 O HM 130-038-00 PO T TRIM 500B HO RIZ
100-049-00 RES C F .125W 5% 1K O HM 140-025-00 RES TF SM .1W 5% 10 O HM
100-050-00 RES C F .125W 5% 1K1 O HM 140-057-00 RES TF SM .1W 5% 220 O HM
100-056-00 RES C F .125W 5% 2K O HM 140-060-00 RES TF SM .1W 5% 300 O HM
100-061-00 RES C F .125W 5% 3K3 O HM 140-065-00 RES TF SM .1W 5% 470 O HM
100-068-00 RES C F .125W 5% 6K2 O HM 140-068-00 RES TF SM .1W 5% 620 O HM
100-071-00 RES C F .125W 5% 8K2 O HM 140-073-00 RES TF SM .1W 5% 1K0 O HM
100-072-00 RES C F .125W 5% 9K1 O HM 140-076-00 RES TF SM .1W 5% 1K3 O HM
100-073-00 RES C F .125W 5% 10K O HM 140-078-00 RES TF SM .1W 5% 1K6 O HM
100-075-00 RES C F .125W 5% 12K O HM 140-080-00 RES TF SM .1W 5% 2K0 O HM
100-076-00 RES C F .125W 5% 13K O HM 140-081-00 RES TF SM .1W 5% 2K2 O HM
100-080-00 RES C F .125W 5% 20K O HM 140-083-00 RES TF SM .1W 5% 2K7 O HM
100-082-00 RES C F .125W 5% 24K O HM 140-087-00 RES TF SM .1W 5% 3K9 O HM
100-083-00 RES C F .125W 5% 27K O HM 140-089-00 RES TF SM .1W 5% 4K7 O HM
100-084-00 RES C F .125W 5% 30K O HM 140-092-00 RES TF SM .1W 5% 6K2 O HM
100-086-00 RES C F .125W 5% 36K O HM 140-094-00 RES TF SM .1W 5% 7K5 O HM
100-089-00 RES C F .125W 5% 47K O HM 140-097-00 RES TF SM .1W 5% 10K O HM
100-092-00 RES C F .125W 5% 62K O HM 140-106-00 RES TF SM .1W 5% 24K O HM
100-093-00 RES C F .125W 5% 68K O HM 140-108-00 RES TF SM .1W 5% 27K O HM

20 PARTS
VERSIO N 1.1

PART # DESC RIPTIO N PART # DESC RIPTIO N


140-111-00 RES TF SM .1W 5% 36K O HM 300-003-00 DIO SW DL4148 100V SM
140-115-00 RES TF SM .1W 5% 51K O HM 300-007-00 DIO SW 1SS244-SUB 1SS245
140-123-00 RES TF SM .1W 5% 100K O HM 301-006-00 THY 2N6507 400V
140-124-00 RES TF SM .1W 5% 120K O HM 301-007-00 DIO PWR DUAL FEP30 (D7)
140-139-00 RES TF SM .1W 5% 470K O HM 301-008-00 DIO PWR DUAL FEN30 (D8)
140-147-00 RES TF SM .1W 5% 1M O HM 301-009-00 DIO PWR 1N4004
145-318-00 RES MF SM .1W 1% 2K00 O HM 301-010-00 DIO PWR 1N5404 3A 400V
145-389-00 RES MF SM .1W 1% 10K0 O HM 301-014-00 DIO PWR 1N4007
145-397-00 RES MF SM .1W 1% 12K1 O HM 302-001-00 DIO ZEN 1N5261B 47V 500MW
145-406-00 RES MF SM .1W 1% 15K0 O HM 302-003-00 DIO ZEN 1N4745A 16V 1W
145-469-00 RES MF SM .1W 1% 68K1 O HM 304-001-00 LED RED T-1
145-478-00 RES MF SM .1W 1% 84K5 O HM 304-004-00 LED G REEN T-1
145-485-00 RES MF SM .1W 1% 100K O HM 310-002-00 XSTR PNP 2N4403
145-547-00 RES MF SM .1W 1% 442K O HM 310-007-00 XSTR NPN 2N4401
150-009-00 RES FUS .25W 5% 2.2 O HM 310-023-02 XSTR NPN 2SC 2362K TR
150-037-00 RES FUS .25W 5% 33 O HM 310-028-00 XSTR PNP 2SB940A PO WER
150-045-00 RES FUS .25W 5% 68 O HM 310-029-00 XSTR NPN 2SD1264A PO WER
200-001-02 PLY .012UF 10% 100V TR 310-032-02 XSTR PNP 2SA1016K TR
200-004-02 PLY .047UF 10% 100V TR 310-033-00 XSTR PNP MJL21193
200-007-02 PLY .01UF 10% 100V TR 310-034-00 XSTR NPN MJL21194
200-015-02 PLY .0047UF 10% 100V PEI 310-035-00 XSTR PNP 2SA1478
200-022-02 PLY .47UF 5% 50V TR 310-036-00 XSTR NPN 2SC 3788
200-023-00 PLY/ BX .001UF 20% 250V Y2 310-037-00 XSTR NPN MJE340 PO WER
200-024-00 PLY/ BX .01UF 20% 250V Y2 310-038-00 XSTR PNP MJE350
200-025-02 PLY/ BX .56UF 5% 63V TR 310-042-00 XSTR NPN MJE15032
200-036-00 PLY/ BX .1UF 10% 250V 310-043-00 XSTR PNP MJE15033
205-002-02 MIC A 270PF 5% 500V TR 311-002-00 XSTR PNP MMST4403 SM
210-001-02 C ER .01UF +80/ -20% 50V TR 320-004-00 O PAMP 4560F
210-010-02 C ER 47PF 5% 500V NPO TR 323-001-00 LM339 Q UAD C O MP
210-017-02 C ER 470PF 5% 500V Y5E TR 323-002-00 LM339D Q UAD C O MP SM
211-003-00 C ER .001UF 10% 50V AX 329-012-00 VTL5C 10 O PTO C O UPLER
211-009-00 C ER .1UF 20% 50V AX 329-014-00 LM35DZ PREC TEMP SENSO R
212-001-00 C ER .01UF 10% 50V X7R SM 400-059-00 TERM Q DISC .250 MALE PC MT
212-004-00 C ER 220PF 5% 50V NPO SM 400-060-00 FUSE C LIP PC MT 5MM DIA
212-009-00 C ER 47PF 5% 50V NPO SM 400-061-00 HDR 2P .100X1 STR LO C K
212-010-00 C ER .1 +80/ -20 25V Z5U SM 400-065-00 TERM Q DISC .250 F 18-22G A
220-001-02 LYT 22UF 20% 25V RAD TR 400-077-00 HDR 20P .1X2 STR LC K SHRD
220-002-02 LYT 47UF 20% 25V RAD TR 400-078-00 HDR 10P .1X2 STR LC K SHRD
220-004-02 LYT 470UF 20% 6.3V RAD TR 400-083-00 2P .100X1 22G A END
220-007-00 LYT 100UF 20% 100V RAD 400-118-00 JAC K 1/ 4 HO RIZ PC MNT MO NO
220-011-02 LYT 100UF 20% 25V RAD 400-119-00 TERM BANANA Q UAD HRZ PC MT
220-014-00 LYT 2.2UF 20% 50V RAD 400-129-00 FUSE C LIP .25 DIA PC MNT
220-025-00 LYT 1000UF 20% 35V RAD 400-133-00 HDR 6C K 11A/ 600V
220-027-02 LYT 10UF 20% 50V RAD TR 400-134-00 REC P 6C K 11A/ 600V
220-033-00 LYT 10000UF 20% 80V RAD 400-135-00 TERM 11A/ 600V F 18-20G A
220-034-00 LYT .47UF 20% 100V RAD 400-138-00 SPEAKO NS HO RIZ 4 C KT
220-035-00 LYT 12000UF 20% 80V RAD 400-141-00 XLR 3P F VERT A-SERIES
220-039-00 LYT 1000 20 25V RAD SMDIA 400-142-00 XLR 3P M VERT A-SERIES
220-040-00 LYT 10UF 20% 160V RAD 400-143-00 HDR 3P .100X1 STR
300-001-00 DIO SIG 1N4148 100V 500MW 400-171-00 HDR 2P .100X1 STR

PARTS 21
M•1200/M•1400 SERVIC E MANUAL

PART # DESC RIPTIO N PART # DESC RIPTIO N


400-172-00 TERM SO LDER-IN 18AWG 700-058-02 MC H 4-40X1/ 2 SKT C LRZC
400-173-00 TERM .25 Q KDS PC MT STABLE 700-059-00 HEX 5/ 16-18X3IN G D-5
400-210-00 TERM Q DISC .250 F 18-22G A 704-001-01 PEMNUT 6-32 .038 STL
400-214-00 JAC K 1/ 4 V PC MNT 1MM WASH 704-001-02 PEMNUT 6-32 .054 STL
410-003-00 INSL SILPAD K6 W/ ADHESIVE 704-007-01 PEMNUT 4-40X.060L SS FLSH
500-022-00 SW RC KR ILLUMINATED 704-023-03 STUD 6-32X.500 STL FLSH
500-023-00 SW SLIDE 4P3T MINI 705-001-00 KEPNUT 6-32
500-024-00 SW SLIDE DPDT MINI 705-003-00 NUT (SPLD W/ JAC K)
501-002-00 RELAY SPDT 30AMP 110VDC 705-013-00 NUT HEX M7 BLK
510-017-00 FUSE SB 20A 3AB 1/ 4X1-1/ 4 705-015-00 NUT SLO T NC KL SPLD W/ JAC K
510-021-00 FUSE FB 10A 5X20MM 250V 705-018-00 NUT HEX 5/ 16-18 (G D-5)
550-219-00 BRKT FAN PS - SR40.8 706-036-01 6-32X.188L STL PEM
550-221-00 TO P C O VER - M1200 706-036-03 STDF 6-32X.312L STL PEM
550-222-00 BTM C O VER - M1200 706-045-00 SPC R PVC .770 LED HI TEMP
550-223-10 SIDE RAIL RIG HT - M1200 710-002-00 WASHER (SPLD WITH JAC K)
550-223-20 SIDE RAIL LEFT - M1200 710-013-00 WASH FLAT NO .6 FIBRE
550-224-00 BRAC KET SUBSINK - M1200 710-017-00 WASH SPLTLC K 5/ 16 HEAVY
550-225-00 HEATSINK C O WLING - M1200 710-019-00 WASH FIBRE BLK (W/ JAC K)
550-237-00 SPRING C LIP SUBSINK-M1200 710-020-00 WASH NO .4 C O MPRESSIO N
550-244-00 BO TTO M C O VER - M1400 710-022-00 WASH FLAT NO .4 FENDER
550-247-00 SHIELD INPUT - M1200 710-023-00 WASH STAR M7 .020 THK
550-249-00 PLATE XFMR MTG - M1200 710-024-00 WASH FLAT 5/ 16 HARD (USS)
550-255-00 PIG G YBAC K C LIP 711-001-00 LUG NO .6 SO LDER STAR
550-275-00 SPAC ER PLATE - AMPLIFIER 712-020-00 BRKT ANG 6-32X.037THK STL
550-277-00 SC REEN MANIFO LD - M1400 712-021-01 RVT C L END .125X.062-.125
551-029-00 EXTR SC RN DSPLY BZL-M1200 740-004-00 STRAIN RELIEF HEYC O 1244
551-029-10 EXTR SC RN DSPLY BZL-M1400 760-048-04 KNO B 9MM DARK G RAY
551-032-00 EXTR FAB HEATSINK - M1200 760-061-00 KNO B VO LUME M1200
553-002-01 C RS 18G A 36 X 120 770-006-00 FAN 80MM 24VDC -MEC HATRO NI
553-002-03 C RS 18G A 48 X 120 770-007-00 FAN 80MM 24VDC -PANASO NIC
553-006-03 EG 18G A 48 X 120 780-042-00 INSUL MYLAR INPUT SHIELD
553-007-03 AL .063 48 X 120 780-114-00 RUBBER WASHER - THIN
553-010-03 EG 20G A 48 X 120 790-002-00 BAG PO LY 12 X 18 2MIL
553-015-03 AL .125 1100 H14 48 X 120 790-016-00 BAG PO LY 24X30 4MIL-M1200
553-017-01 SS .048 17-7 36 X 120 800-066-00 BO X M1200
600-016-00 XFMR M1200 120V 800-069-00 BO X M1400
601-006-00 INDUC TO R AIR C O IL 1UH 810-056-00 INST TO P/ BO TTO M - AMP
611-029-02 WIR 18G A 1007 BLK 5IN ST2 820-062-00 O WN MNL - M1200/ M1400
611-038-00 WR 18G 1010 G N/ YL 4IN ST2 820-062-10 O WN MNL – M1400i
660-005-00 22G A JUMPER WIRE 830-016-00 REG & WARR C ARD FR SERIES
700-005-00 SEMS 8-32X1/ 2 PHP BLKZC
700-010-00 TF 6-32X1/ 4 PHP BLKZC
700-010-04 TF 6-32X3/ 8 PHP BLKZC
700-011-00 MC H 4-40X1/ 4 BTNSKT BLKO X
700-028-02 SEMS 6-32X3/ 8 PHP BLKZC
700-028-04 SEMS 6-32X3/ 4 PHP BLKZC
700-041-04 MC H 6-32X3/ 8 FL 100DG BLK
700-047-04 MC H 10-32X3/ 8 FIL PHL C LR
700-050-04 MC H 6-32X3/ 8 FIL PHL C LR
700-055-00 MC H 4-24X3/ 8 PHP BLK HILO

22 PARTS

You might also like