Adaptronic Modular CAN Output Configuration

Basic information

Bit rate 500 kbps

ECU termination On
Identifier format 11-bit
Base address S300

* All variables are 16-bits, signed, 2s complement

* The "scalar" field means "divide the number by this to display it to
the user". Eg 1000 means that the value has a resolution of 0.001,
and a value of 2500 would be represented to the user as 2.500.
* Temperatures are all expressed in Celcius with a scalar of 10. Eg 25
°C would be represnted by a value of 250.
* Pressures can be gauge, absolute or differential, and are all
expressed in kPa with a scalar of 10. Eg barometric pressure of
101.3 kPa is expressed as 1013.
* Speeds are expressed in km/h with a scalar of 10.
* The ECU thinks in lambda, rather than air-fuel ratio. All lambda
measurements are expressed with a scalar of 1000, ie 1000 means
1.000 lambda. Target lambda has a scalar of 10000, and stoich ratio
is a scalar of 1000, ie 14.7:1 is 14700. Target AFR (used only in
the fuel calculation) is actually AFR, not "petrol AFR".
* All variables are stored as big-endian
* Therefore each CAN frame records 4 variables
* The variable space in the ECU is 1024 variables long
* The address of the first variable is given as the CAN ID minus the
base address, times 4
* An example of the data payload from a CAN frame appears below:

*0* *1* *2* *3* *4* *5* *6* *7*

Variable 0 high Variable 0 low Variable 1 high

Variable 1 low

Variable 2 high

Variable 2 low

Variable 3 high

Variable 3 low

* Not all frames are guaranteed to be transmitted; the user can select
which variables are transmitted
* However the following addresses are always transmitted:

*Offset* *Live variable address range* *First variable* *Second

variable* *Third variable* *Fourth variable*
4 (S004) 16 - 19 Ext 0-5V 2 input voltage 12V supply voltage 5V
sensor supply voltage Sensor ground voltage
16 (S010) 64 - 67 RPM (unused) (unused) (unused)
97 (S061) 388 - 391 IMAP IMAP 2 EMAP EMAP 2
99 (S063)

396 - 399
 TPS overall

TPS1 (electronic throttle)

TPS2 (electronic throttle) TPS3 (electronic throttle)

100 (S064) 400 - 403 TPS4 (electronic throttle) Lambda 1 Lambda 2 ECT
101 (S065) 404 - 407 MAT Oil temp Fuel temp Oil pressure
102 (S066) 408 - 411 Fuel gauge pressure Fuel differential pressure
Servo position Ext 0-5V input 1 (calibrated)
103 (S067) 412 - 415 Ext 0-5V input 2 (calibrated) Sensor GND voltage
with GND disconnected Ethanol percentage from sensor Vehicle speed
104 (S068) 416 - 419 Gear Driven speed Ground (undriven) speed Slip
speed
108 (S06c) 432 - 435 Digital inputs (processed low) Digital inputs
(processed high) Flags (low) Flags (high)
117 (S075) 468 - 471 Lateral undriven wheel slip MGP 1 MGP 2 Knock
max (inc bkg)
120 (S078) 480 - 483 Injector duty cycle 1 Injector duty cycle 2
Injector duty cycle 3 Injector duty cycle 4
129 (S081) 516 - 519 Charge temp 1 Charge temp 2 Stoich ratio
Target lambda
138 (S08a) 552 - 553 Fuel mass cyl 15 Fuel mass cyl 16 Fuel inj
duration 1 Fuel inj duration 2
163 (S0a3) 652 - 655 Ignition timing (leading) Ignition timing
(trailing) (unused) (unused)
165 (S0a5) 660 - 663 Async 1 duration Async 1 strobe Async 2
duration Async 2 strobe
170 (S0aa) 680 - 683 Idle duty cycle from closed loop correction Idle
controller status Unclipped idle effort Final idle effort
176 (S0b0) 704 - 707 Cutting conditions Current RPM limit Pitlane
RPM sampled Pitlane status
177 (S0b1) 708 - 711 Cut percentage from antilag Cut percentage from
traction control Final fuel cut percentage Final ignition cut percentage
186 (S0ba) 744 - 747 Boost control duty cycle 1 unclipped Final boost
control duty cycle 1 Boost controller 1 status Closed loop correction
for boost controller 2

Actual data format

The following is the actual data enabled in this ECU file:

*CAN ID* *Live var address* *Name* *Description* *Unit* *Scalar*

S304 16 Voltage_Ext2 Voltage of Ext 2 input. Max = 5.5V. Input
impedance 55kOhm. Resolution = 1.3mV. On the M1200, this pin is used for
injector 4 current measurement. 1000
17 Voltage_12V Voltage of 12V ignition power supply (pin 7 on J2 of
M2000 / M6000, pin 1B on M1200). This is not the voltage of the ignition
switch input; it's the ECU power supply pin. Max V = 17.5V, resolution =
4.2 mV 1000
18 Voltage_5V Voltage of 5V sensor output pin. Max V = 17.5V,
resolution = 4.2 mV 1000
19 Voltage_SGND current Voltage of the sensor ground pin. Max V =
5.5V. Pulled either to ground inside the ECU, or pulled to 3.5V when
sensor ground is disabled to check for ground loops. The ECU does this
when the 1000
S310 64 RPM Engine speed in RPM. Sampled over a window of 360 crank
degrees or less 1
65 Period for cyl 1 [currently unimplemented] 1000
66 Period for cyl 2 [currently unimplemented] 1000
67 Period for cyl 3 [currently unimplemented] 1000
S361 388 IMAP Intake manifold absolute pressure (as used for
calculation) kPaA 10
389 IMAP 2 Intake manifold absolute pressure for bank 2 (used for
calculation - in dual bank mode) kPaA 10
390 EMAP Exhaust manifold absolute pressure (as used for calculation)
kPaA 10
391 EMAP 2 Exhaust manifold absolute pressure for bank 2 (as used for
calculation - in dual bank mode) kPaA 10
S363 396 TPS overall TPS value used for throttle based calculations;
MAP prediction etc. Should be from the actual throttle sensor. 100
397 TPS 1 (DBW) TPS from electronic throttle #1 100
398 TPS 2 (DBW) TPS from electronic throttle #2 100
399 TPS 3 (DBW) TPS from electronic throttle #3 100
S364 400 TPS 4 (DBW) TPS from electronic throttle #4 100
401 Lambda Measured lambda value, or lambda for bank 1 in dual bank
engines lambda 1000
402 Lambda 2 Measured lambda value for bank 2 in dual bank engines
lambda 1000
403 ECT Measured coolant temperature deg C 10
S365 404 MAT Measured air temperature deg C 10
405 Oil T Measured oil temperature deg C 10
406 Fuel T Measured fuel temperature deg C 10
407 Oil P Measured oil pressure (gauge pressure) kPaG 10
S366 408 Fuel P Measured fuel pressure (gauge pressure) kPaG 10
409 Diff Fuel P Calculated differential fuel pressure (from IMAP, fuel
pressure and barometric pressure) kPaD 10
410 Servo pos Calibrated servo position from 0-100%. By default, used
for metering oil pump position feedback and other things. 10
411 0-5V Ext 1 Calibrated external input 1 0-5V input (not available
on M1200) 10
S367 412 0-5V Ext 2 Calibrated external input 2 0-5V input (not
available on M1200) 10
413 Sens GND V (GND off) The sensor ground voltage when the ground
output at the ECU was disabled, when the ECU was first powered up. If
this is close to zero, it usually means that there's a ground loop and
that sensor ground is shorted to the engine outside the ECU. Normally
this will be about 1.5V or more. 1000
414 Ethanol Content Ethanol percentage read from the flex fuel sensor
directly, shows dash if there is no valid reading from the sensor or if
no direct connection sensor is configured. 10
415 Vehicle speed Vehicle speed (measured from the driven wheels)
km/h 10
S368 416 Gear number Detected gear number, either from matching
RPM/VSS or reading an analogue gear position sensor on the gearbox. In
RPM / VSS mode, if the clutch input is active or the vehicle is stopped
then the gear number will show zero (neutral). 1
417 Driven speed Driven wheel speed (average of both wheels on a car
with sensors for both wheels) km/h 10
418 Ground speed Ground wheel speed (or average of both undriven
wheels) km/h 10
419 Spd diff (drive-gnd) Driven wheel speed minus ground wheel speed
(slip speed) km/h 10
S36C 432 Dig inp processed low Processed digital inputs. CLUTCH (bit
0), ELEC LOAD (bit 1), AIRCONSW (air conditioner request) (bit 2), WOT
(wide open throttle switch input, does not activate when pedal goes to
100%) (bit 3), CLOSEDTHROTTLE (closed throttle switch input, does not
activate when TPS=0%, it's for a separate digital switch input) (bit 4),
NOS (nitrous enable) (bit 5), STRAIN (strain gauge digital input on
sequential gear shifter) (bit 6), TURBOCANCEL (cancel turbo timer switch
input) (bit 7), ALTMAP (enable fuel / ignition map 2) (bit 8), TC SW
(traction control enable switch) (bit 9), LC SW (launch control enable
switch) (bit 10), ELECLOAD2 (bit 11), PSTEER (power steering engine
load) (bit 12), PUSHTOPASS (push to pass / scramble boost digital input)
(bit 13), PITLANESPEED (pit lane speed limit) (bit 14), BOOST1 (boost
switch 1 input) (bit 15) 1
433 Dig inp processed hi Processed digital inputs. BOOST2 (boost
switch 2 input) (bit 0) 1
434 Flags low Status flags. CLOSEDTHROTTLE (closed throttle condition,
either from pedal position on DBW, throttle position on cable throttle,
or CLOSEDTHROTTLE digital input) (bit 0), WOT (wide open throttle
condition, either from pedal positionon DBW, throttle position on cable
throttle, or WOT digital input) (bit 1), POWERON (12Vpower is applied,
ECU is calculating / running) (bit 2), CRANKING (engine has not fired
yet, it's either stopped or we're cranking) (bit 3), HAVEPERIOD (ECU has
TDC information, but not necessarily the cylinder number) (bit 4),
HAVE360 (ECU has 360 degrees of information, eg from a crank sensor, but
not necessarily 720 degrees - in other words, ECU can do wasted spark
ignition on a 4 stroke or direct fire / sequential injection on a
2-stroke / rotary) (bit 5), HAVE720 (ECU has 720 degrees of information,
can do fully sequential injection and direct fire ignition on a 4-stroke
engine) (bit 6), MAP2 (the second fuel / ignition maps are currently
engaged) (bit 7), ACON (Air conditioner is on, additional idle effort
enabled) (bit 8), ACCOMPON (Air conditional compressor is on - happens a
delay after ACON) (bit 9), THERMO1 (first stage thermofan on) (bit 10),
THERMO2 (second stage thermofan) (bit 11), THERMO3 (third stage
thermofan) (bit 12), CLUTCH (clutch or neutral input is triggered or car
is stopped) (bit 13), HAVE3602 (have had 360 degrees of information for
at least 2 crank cycles) (bit 14), HAVE3603 (have had 360 degrees of
information for at least 3 crank cycles) (bit 15) 1
435 Flags high Status flags. CLOSEDFUEL (in closed loop fuel mode)
(bit 0), CLOSEDIDLE (in closed loop idle mode) (bit 1), IDLEDERIV (idle
derivative enabled, eg coming back down to idle) (bit 2), IDLEHOMED
(idle stepper motor is homed, happens when ECU is first powered up with
12V) (bit 3), LAUNCHENA (launch control enabled) (bit 4), INLAUNCH
(launch control currently triggered) (bit 5), TCENA (traction control
enabled) (bit 6), INTC (traction control currently triggered) (bit 7),
INANTILAG (antilag currently triggered) (bit 8), FUELPUMPON (fuel pump
output triggered) (bit 9), INTWINTURBO (2nd turbo enabled in sequential
twin turbo system) (bit 10), CLOSEDBOOST (in closed loop boost mode)
(bit 11), LOCKED (ECU settings are locked, can't be read out) (bit 12),
NEEDREAD (PC needs to read updated settings out from the ECU) (bit 13),
ABOVEOVERRUN (RPM has gone above the overrun RPM threshold) (bit 14),
MIN PW CLIP (injector duration has been clipped by the minimum
pulsewidth or minimum fuel delivery setting) (bit 15) 1
S375 468 Slip LR Ground Lateral slip of undriven wheels 100
469 MGP1 Manifold gauge pressure for bank 1. Calculated by IMAP 1 -
Baro pressure kPaG 10
470 MGP2 Manifold gauge pressure for bank 2. Calculated by IMAP 2 -
Baro pressure kPaG 10
471 Knock max (inc bkg) Maximum knock reading of all cylinders (before
background is subtracted) 1000
S378 480 Injector 1 duty Duty cycle for injector output 1 100
481 Injector 2 duty Duty cycle for injector output 2 100
482 Injector 3 duty Duty cycle for injector output 3 100
483 Injector 4 duty Duty cycle for injector output 4 100
S381 516 Calc Charge temp 1 Calculated charge temperature for bank 1
(blend of air temp and coolant temp, in accordance with the manifold
heat soak map) deg C 10
517 Calc Charge temp 2 Calculated charge temperature for bank 2 (blend
of air temp and coolant temp, in accordance with the manifold heat soak
map) deg C 10
518 Stoichiometric ratio Current stoichiometric ratio, either ECU
setting or interpreted from the flex sensor 1000
519 Target Lambda Target lambda value, looked up from the target
lambda map lambda 10000
S38A 552 Fuel mass cyl 15 Fuel mass to inject for cylinder 15 (after
individual cylinder fuel trim) 10
553 Fuel mass cyl 16 Fuel mass to inject for cylinder 16 (after
individual cylinder fuel trim) 10
554 Fuel inj dur out 1 Fuel injector duration (pulsewidth) for output
1 1000
555 Fuel inj dur out 2 Fuel injector duration (pulsewidth) for output
2 1000
S3A3 652 Ignition timing Ignition timing, or ignition timing leading
on spark split engines eg rotaries 10
653 Ignition timing (trail) Ignition timing trailing on spark split
engines eg rotaries 10
654 Advance metric (raw) [currently unimplemented] 1
655 Advance metric (filt) [currently unimplemented] 1
S3A5 660 Async inj duration Duration of async injection pulse, for
injector outputs 1-16, bank 1 1000
661 Async inj strobe 1-16 Enable async injection for injector outputs
1-16, bank 1 1
662 Async inj duration 2 Duration of async injection pulse, for
injector outputs 1-16, bank 2 1000
663 Async inj str 1-16 2 Enable async injection for injector outputs
1-16, bank 2 1
S3AA 680 Idle effort closed lp Additional idle effort from closed
loop idle control 100
681 Idle closed lp status 0 = in open loop, 2 = closed loop idle
(derivative only). 3 = in full closed loop idle 1
682 Unclipped idle effort Idle valves added together (could be less
than the minimum value or greater than 100) 100
683 Idle effort / duty Final idle effort, between the range of the
minimum idle effort setting and 100% 100
S3B0 704 Cutting conditions Power cutting conditions: FUELPT (fuel
pressure safety cut) (bit 0), OILT (oil temperature safety cut) (bit 1),
OILP (oil pressure safety cut) (bit 2), AFR (lean-out protection) (bit
3), OCINJ (open circuit injector) (bit 4), OVRBOOST (over boost) (bit
5), REVL (rev limiter) (bit 6), OVERRUN (overrun / decel fuel cut) (bit
7), FCLEAR (flood clear, ie injector cut during cranking) (bit 8),
PITLANE (ignition cut due to pit lane limit) (bit 9), LAUNCH (ignition /
fuel cut due to launch control) (bit 10), ANTILAG (ignition cut due to
antilag) (bit 11), FLATSHIFT (ignition cut due to flatshift) (bit 12),
ETHROTTLE (TPS is being closed for power reduction) (bit 13), FUEL (fuel
cut is in progress) (bit 14), IGN (ignition cut is in progress) (bit 15)
1
705 Current RPM limit Current RPM limit, from either safety function
or the coolant temp dependent rev limit table 1
706 Pitlane RPM limit Pitlane RPM limit, taken from sampling the RPM
when the vehicle speed matched the pitlane speed setting 1
707 Pitlane status [currently unimplemented] 1
S3B1 708 Pwr cut (antilag) [currently unimplemented] 1
709 Pwr cut (traction) [currently unimplemented] 1
710 Fuel cut Final fuel cut percentage 1
711 Ignition cut Final ignition cut percentage 1
S3BA 744 Unclipped WG value1 Total wastegate duty cycle 1 (before
clipping between zero and maximum value) 100
745 Wastegate 1 duty Final wastegate duty cycle 1 100
746 Boost ctrl status Boost controller status. PUSHTOPASS (push to
pass currently active) (bit 0) 1
747 Closed lp WG 2 corr Closed loop correction to wastegate duty cycle
2 100