PLC - DVP Series Manual •

UT-14SS2-A UT-12SE-A1
Industrial Automation Headquarters
Delta Electronics, Inc.
Taoyuan Technology Center
18 Xinglong Road, Taoyuan District,
Taoyuan City 33068, Taiwan
TEL: 886-3-362-6301 / FAX: 886-3-371-6301
www.deltaww.com.tw

Asia
Delta Electronics (Jiangsu) Ltd.
Wujiang Plant 3
1688 Jiangxing East Road,
Wujiang Economic Development Zone
Wujiang City, Jiang Su Province, P.R.C. 215200
TEL: 86-512-6340-3008 / FAX: 86-769-6340-7290

Delta Greentech (China) Co., Ltd.

238 Min-Xia Road, Pudong District,
ShangHai, P.R.C. 201209
TEL: 86-21-58635678 / FAX: 86-21-58630003

Delta Electronics (Japan), Inc.

Tokyo Office
2-1-14 Minato-ku Shibadaimon,
Tokyo 105-0012, Japan
TEL: 81-3-5733-1111 / FAX: 81-3-5733-1211

Delta Electronics (Korea), Inc.

1511, Byucksan Digital Valley 6-cha, Gasan-dong,
Geumcheon-gu, Seoul, Korea, 153-704
TEL: 82-2-515-5303 / FAX: 82-2-515-5302

Delta Electronics Int’l (S) Pte Ltd.

4 Kaki Bukit Ave 1, #05-05, Singapore 417939
TEL: 65-6747-5155 / FAX: 65-6744-9228

Delta Electronics (India) Pvt. Ltd.

Plot No 43 Sector 35, HSIIDC
Gurgaon, PIN 122001, Haryana, India
TEL : 91-124-4874900 / FAX : 91-124-4874945

Americas
Delta Products Corporation (USA)
Raleigh Office
P.O. Box 12173,5101 Davis Drive,
Research Triangle Park, NC 27709, U.S.A.
TEL: 1-919-767-3800 / FAX: 1-919-767-8080

Delta Greentech (Brasil) S.A.

Sao Paulo Office
Rua Itapeva, 26 - 3° andar Edificio Itapeva One-Bela Vista
01332-000-São Paulo-SP-Brazil
TEL: 55 11 3568-3855 / FAX: 55 11 3568-3865
2018-11-26
Europe 5014051201
Delta Electronics (Netherlands) B.V.
Eindhoven Office
De Witbogt 20, 5652 AG Eindhoven, The Netherlands
TEL: +31 (0)40-8003800 / FAX: +31 (0)40-8003898
UTA1
*We reserve the right to change the information in this catalogue without prior notice.
PLC - DVP Series

Manual
UT-14SS2-A
UT-12SE-A1
 Starter Kit Manual

Table of Contents

Chapter 1 Introduction of UT Series Starter Kits

1.1 General Information about UT Series Starter Kits ................ 1-2

1.2 System Requirements for a Starter Kit ............................ 1-10

1.3 Description of ISPSoft-Programming Tool for PLCs ............ 1-11

1.4 Description of DOPSoft-Programming Tool for HMIs........... 1-13

1.5 Description of DCISoft ................................................... 1-15

Chapter 2 Installation of UT Series Starter Kits

2.1 Installing Hardware ........................................................ 2-2
2.1.1 Connecting a PLC to an I/O Simulator Board and a Power
Supply Module ..................................................... 2-2
2.1.2 Connecting a Personal Computer to DVP14SS211R ..... 2-5
2.1.3 Connecting a Personal Computer to DOP-107BV ......... 2-5
2.1.4 Connecting DVP14SS211R to DOP-107BV .................. 2-6
2.1.5 Connecting a Personal Computer to DVP12SE11R ....... 2-7
2.1.6 Connecting a Personal Computer to DOP-107EV ......... 2-7
2.1.7 Connecting DVP12SE11R to DOP-107EV .................... 2-7

2.2 Installing ISPSoft ........................................................... 2-8

2.3 Installing COMMGR ........................................................ 2-14

2.4 Installing DOPSoft ......................................................... 2-18

2.5 Installing DCISoft .......................................................... 2-27

2.6 Installing the UC-PRG020-12A Driver ............................. 2-31

i
Chapter 3 Example Programs
3.1 Example 1 ................................................................... 3-3
3.1.1 Creating a Project for a PLC ..................................... 3-3
3.1.2 Creating a Main Program ......................................... 3-6
3.1.3 Setting COMMGR for UT-14SS2-A............................ 3-15
3.1.4 Downloading a PLC Project ..................................... 3-18
3.1.5 Monitoring a Program ............................................ 3-21
3.1.6 Using a PLC with an I/O Simulator Board ................. 3-23
3.1.7 Writing a Program for an HMI ................................. 3-24
3.1.8 Compiling and Downloading an HMI Program ............ 3-50
3.1.9 Using an HMI with an I/O Simulator Board ............... 3-52

3.2 Example 2 .................................................................. 3-55

3.2.1 Project Requirements ............................................ 3-55
3.2.2 Project Development ............................................. 3-56
3.2.3 Writing a Program for an HMI ................................. 3-58
3.2.4 Creating a Project for a PLC .................................... 3-80
3.2.5 Setting COMMGR for UT-12SE-A1 ............................ 3-93
3.2.6 Downloading a PLC Project ..................................... 3-96
3.2.7 Setting Ethernet Parameters for DVP12SE11R .......... 3-98
3.2.8 Testing a Project ................................................. 3-102

Chapter 4 Appendix
4.1 Introduction of Hardware ................................................ 4-3
4.1.1 DVPPS01 ............................................................... 4-3
4.1.2 DVP14SS211R ........................................................ 4-3
4.1.3 DVP12SE11R.......................................................... 4-3
4.1.4 DOP-107BV............................................................ 4-4

ii
 4.1.5 DOP-107EV ............................................................ 4-4

4.2 Profiles and Dimensions .................................................. 4-5

4.2.1 DVPPS01 ............................................................... 4-5
4.2.2 DVP14SS211R ........................................................ 4-5
4.2.3 DVP12SE11R.......................................................... 4-7
4.2.4 DOP-107BV............................................................ 4-8
4.2.5 DOP-107EV ............................................................ 4-9

4.3 Connecting Communication Cables .................................. 4-10

4.3.1 Pin Definitions of Serial Communication .................... 4-10
4.3.2 Introduction of Communication Cables ..................... 4-12

4.4 Communication between a PLC and an HMI ...................... 4-14

4.4.1 Wiring a Controller ................................................. 4-14
4.4.2 PLC Device Addresses ............................................ 4-15
4.4.3 Setting the Communication Parameters in a PLC ........ 4-18
4.4.4 Setting the Communication Parameters in an HMI...... 4-21

4.5 Equivalent Circuit of an I/O Simulator Board..................... 4-23

4.5.1 Connecting to DVP14SS211R .................................. 4-23
4.5.2 Connecting to DVP12SE11R .................................... 4-24

4.6 Installing the DVP12SE11R Driver ................................... 4-25

iii
 1
Chapter 1 Introduction of UT Series Starter
Kits

Table of Contents

1.1 General Information about UT Series Starter Kits ....... 1-2

1.2 System Requirements for a Starter Kit ...................... 1-10

1.3 Description of ISPSoft-Programming Tool for PLCs ... 1-11

1.4 Description of DOPSoft-Programming Tool for HMIs . 1-13

1.5 Description of DCISoft .............................................. 1-15

1-1
 St a r t e r K i t M a n u a l

1.1 General Information about UT Series Starter

_1 Kits
This UT series starter kit simplifies users’ entry into the world of Delta PLCs and HMIs,
and helps the users get familiar with programming software.

For that purpose, this manual explains how to connect the components of a starter kit,
and how to program the PLC and HMI by means of several simple examples.

Components of UT series starter kits:

There are two types of starter kits. Users can select a type of starter kit according to their
needs.

1. UT-14SS2-A: For learning PLC and HMI programming

 Components of the UT-14SS2-A starter kit:

Item Model name Description

A Starter Kit Manual User manual

B DVP-PS01 Power supply module, 24 V DC output

C DVP14SS211R CPU with 14 built-in I/O points

1-2
 C h a p t e r 1 I n t r o d u c t i o n o f U T S e r i e s St a r t e r K i t s

Item Model name Description

D DOP-107BV HMI, 7” TFT LCD

1_
E UC-MS020-06A (2 m) Communication cable for connecting an HMI to a PLC

F UC-PRG020-12A (2 m) Programming cable for a PLC

G UC-PRG015-02A (1.5 m) Programming cable for an HMI

H 3865259300 DC power cable

I 3081419700 RS-485 cable for connecting a PLC to an HMI

J 3534435700 Four screw locks for an HMI

K 5502577100 I/O simulator board

L UT-USB01 USB flash drive

 DVP14SS211R:

 POWER indicator, RUN indicator,  RUN/STOP switch

ERROR LED indicator

 COM1 (RS-232 port)  COM2 (RS-485 port)

 DC power input  Input/Output terminals
 Input/Output point indicators  Extension port

1-3
 St a r t e r K i t M a n u a l

2. UT-12SE-A1: For learning PLC and HMI programming and Ethernet connection

 Components of the UT-12SE-A1 starter kit:

_1

Item Model name Description

A Starter Kit Manual User manual

B DVP-PS01 Power supply module, 24 V DC output

C DVP12SE11R CPU with 12 built-in I/O pints

D DOP-107EV HMI, 7” TFT LCD, support Ethernet

E UC-PRG030-20A (3 m) Ethernet cable

F UC-PRG015-01A (1.5 m) Programming cable for a PLC

G UC-PRG015-02A (1.5 m) Programming cable for an HMI

H 3865259300 DC power cable

I 3081419700 RS-485 cable for connecting a PLC to an HMI

J 3534435700 Four screw locks for an HMI

K 5502577101 I/O simulator board

1-4
 C h a p t e r 1 I n t r o d u c t i o n o f U T S e r i e s St a r t e r K i t s

Item Model name Description

L UT-USB01 USB flash drive

1_
 DVP12SE11R:

 POWER indicator, RUN indicator,  RUN/STOP switch

ERROR indicator, COM1 indicator

 COM1 (Mini USB)  Ethernet port

 COM2 (RS-485)  DC power input

 Input/Output terminals, COM3 (RS-485)  Input/Output point indicators, COM2

indicator, COM3 indicator

 Right-side extension port

1-5
 St a r t e r K i t M a n u a l

 USB flash drive:

_1 Item Contents

1. ISPSoft
2. COMMGR
Software 3. DOPSoft
4. DCISoft
5. UC-PRG020-12A driver

1. Starter Kit Manual

2. ISPSoft User Manual
3. DOPSoft User Manual
4. DVP-ES2/EX2/SS2/SA2/SX2/SE&TP Operation Manual - Programming
5. Starter Kit Application Examples
Manual 6. Instruction Sheet (DVPPS01/02/05)
7. Instruction Sheet (DVP-SS2)
8. Instruction Sheet (DVP-SE)
9. Instruction Sheet (UC-PRG020-12A)
10. Instruction Sheet (DOP-107BV)
11. Instruction Sheet (DOP-107EV)

1. HMI Element Example

2. Examples (UT-14SS2-A)
Program
3. Examples (UT-12SE-A1)
4. DVP PLC Application Examples

1-6
 C h a p t e r 1 I n t r o d u c t i o n o f U T S e r i e s St a r t e r K i t s

 Starter kit setup wizard:

(1) Insert the USB flash drive which is an attachment to a UT series starter kit 1_
into a computer, and double-click “StarterKit.exe” in the USB flash drive.

(2) There are three options.

 Install Software
After users click Install Software, they can select the software which needs
to be installed.

(A) ISPSoft version x.xx: PLC programming software

(B) COMMGR version x.xx: Communication management software

(C) DOPSoft version x.xx.xx: HMI programming software

(D) DCISoft version x.xx (UT-12SE-A1): Network module configuration

software

(E) UC-PRG020-12A driver (UT-14SS2-A)

1-7
 St a r t e r K i t M a n u a l

_1

 Review Documentation
After users click Review Documentation, they can select the manual that
they want to read from the list box displayed, and then click Open to open the
manual.

1-8
 C h a p t e r 1 I n t r o d u c t i o n o f U T S e r i e s St a r t e r K i t s

 Browse Examples
After users click Browse Examples, they can choose to open an HMI
1_
element example or PLC application examples according to their needs.

(A) HMI Element Example: Demo of HMI elements

(B) Examples (UT-14SS2-A): Examples in Chapter 3

(C) Examples (UT-12SE-A1): Examples in Chapter 3.

(D) DVP PLC Application Examples: Program codes for DVP PLC
Application Examples

1-9
 St a r t e r K i t M a n u a l

1.2 System Requirements for a Starter Kit

_1 Before using a starter kit, users have to make sure that an operating system meets the
requirements below.

Item System requirement

Operating system Windows 2000/NT/Me/XP/Vista/7/8/10

CPU/Memory Pentium 1.6 G or above/2 GB or above

Hard disk drive Capacity : 2 GB or above

Monitor Full-color display supporting a resolution higher than 1024 x 768 pixels

Keyboard/Mouse General keyboard/mouse, or device compatible with Windows

Printer with a driver for Windows (It is used to print projects, and is
Printer
optionally required.)

Communication COMMGR, a communication manager, must be installed on a

software computer. (*1)

*1. Please refer to ISPSoft User Manual for more information about COMMGR. ISPSoft needs
to be connected to a PLC by means of COMMGR.

1-10
 C h a p t e r 1 I n t r o d u c t i o n o f U T S e r i e s St a r t e r K i t s

1.3 Description of ISPSoft-Programming Tool for

PLCs
1_
ISPSoft is a programming tool that realizes high-level to IEC 61131-3 standard
programming concept for PLCs, and enables genuine structured design.

The interface of ISPSoft is described below.

 Function area: The main functions of ISPSoft are included. The functions which are
used more frequently are on the toolbars, and the functions which are used less
frequently are on the menu bar.

 Project management area: The framework of a project is displayed in this area.

Users can understand the relation among the objects in the project by means of the
tree structure. The efficiency in managing the project is also increased.

 Working area: Users can edit a project in this area.

 Output area: The execution of some functions generates information. The information
is displayed in this area.

 Status area: The information about a project and communication is displayed in this
area.

1 - 11
 St a r t e r K i t M a n u a l

When using ISPSoft, the users can click an item on the Help menu to get help.

_1

Item Description

Users can get the information about the version of the software, and
About…
the date when the software is released.

Users can get the usage of the software. (Alternatively, the users
ISPSoft User Index
can click on the file toolbar to get the usage of the software.)

Users can get the information about instructions and registers. If the
PLC Instruction and Special
users click an instruction in the program editing area and press F1
Registers Reference
on the keyboard, they can get the information about the instruction.

The features of ISPSoft are listed below.

1. Enhancement of structured development

Based on the IEC 61131-3 standard, basic program units are called “program
organization units” (POUs). The management of a group of POUs by means of a
tree structure is added. This function can provide hierarchical management.

2. Supporting Large-scale project development

With the trend that the size of application software increases, it is getting common for
several developers to work together on a program. ISPSoft manages projects by
means of integrating tasks. The efficient and convenient development environment
that ISPSoft provides enables users to apply PLCs to more complex control systems
as well as to small control systems.

3. Enhanced variable management

Variable programming that does not depend on PLC memory addresses is a

fundamental concept of the ISPSoft to improve program modularization and
re-usability. ISPSoft supports the function of importing and exporting data from and to
Microsoft Excel. With above functions, the tasks of defining and managing variables
can be implemented with greater efficiency.

1-12
 C h a p t e r 1 I n t r o d u c t i o n o f U T S e r i e s St a r t e r K i t s

1.4 Description of DOPSoft-Programming Tool for

HMIs
1_

DOPSoft is powerful easy-to-use HMI configuration software for DOP series HMIs. With
DOPSoft, users can create functional touchscreen applications for industrial processes
such as automation, process control, and OEM applications.

The interface of DOPSoft is described below.

 Menu bar: DOPSoft provides nine menus.

 Toolbars: DOPSoft provides eight toolbars.
 Project management area: The project structure is displayed in the area. Users can
learn about the relationship of objects via the tree structure for enhanced efficiency in
project management.

 Property window: The properties of the elements on the present screen are displayed
in the Property window.

 Output window: The editing actions of users, and the output messages about the
compiling of a program are recorded in the Output window.

1-13
 St a r t e r K i t M a n u a l

 Screen Manager window: If users create several screens, they can preview the
screens by means of the Screen Manager window. The users can know the elements
_1 on a screen in the Screen Manager window without having to switch to that screen. If
the users double-click a screen in the Screen Manager window, they can switch to
that screen rapidly.

 Status bar: It displays the present editing status.

 Editing area: A proper editing area is provided according to the HMI type selected by
users.

DOPSoft allows users to create a project by using features such as animated screens,
alarms, trend graphs, recipes, and reports. DOPSoft and DOP series HMIs make
touchscreen application more visually functional.

1-14
 C h a p t e r 1 I n t r o d u c t i o n o f U T S e r i e s St a r t e r K i t s

1.5 Description of DCISoft

DCISoft is integrated configuration software for Delta network modules. 1_

The interface of DCISoft is described below.

 Menu bar: DCISoft provides four menus.

 Toolbars: DCISoft provides five toolbars.
 Workspace: Network types and models are displayed in this area.
 Output area: Messages are displayed in this area.
 Status bar: It displays information about the present states of the program edited and
the communication executed.

 Operation area: This area is an interface for setting network modules.

1-15
 St a r t e r K i t M a n u a l

MEMO

_1

1-16
 2
Chapter 2 Installation of UT Series Starter
Kits

Table of Contents

2.1 Installing Hardware .................................................... 2-2

2.1.1 Connecting a PLC to an I/O Simulator Board and a Power
Supply Module ....................................................... 2-2
2.1.2 Connecting a Personal Computer to DVP14SS211R ..... 2-5
2.1.3 Connecting a Personal Computer to DOP-107BV ......... 2-5
2.1.4 Connecting DVP14SS211R to DOP-107BV .................. 2-6
2.1.5 Connecting a Personal Computer to DVP12SE11R ....... 2-7
2.1.6 Connecting a Personal Computer to DOP-107EV ......... 2-7
2.1.7 Connecting DVP12SE11R to DOP-107EV .................... 2-7

2.2 Installing ISPSoft........................................................ 2-8

2.3 Installing COMMGR ................................................... 2-14

2.4 Installing DOPSoft .................................................... 2-18

2.5 Installing DCISoft ..................................................... 2-25

2.6 Installing the UC-PRG020-12A Driver ....................... 2-29

2-1
 St a r t e r K i t M a n u a l

2.1 Installing Hardware

2.1.1 Connecting a PLC to an I/O Simulator Board and a
Power Supply Module

 Assembling the UT-14SS2-A starter kit:

_2
1. Install the digital I/O simulator board.
Please refer to section 4.5.1 for more
information about the equivalent circuit of
the I/O simulator board.

2. Connect a single-phase 110/220 V cable

to the L and N terminals.
Note: To prevent staff from being hurt, the
external AC power which is used should
be switched off before hardware is wired.

3. Use the DC power cable to connect

DVP-PS01 to DVP14SS211R.

2-2
 C h a p t e r 2 I n s t a l l a t i o n o f U T S e r i e s St a r t e r K i t s

4. Use the DC power cable to connect the

digital I/O simulator board to DVP-PS01.

2_

5. Use the DC power cable to connect

DVP-PS01 to DC power input terminals on
DOP-107BV.

6. The assembly of the UT-14SS2-A starter

kit is complete.

 Assembling the UT-12SE-A1 starter kit:

1. Install the digital I/O simulator board.

Please refer to section 4.5.2 for more
information about the equivalent circuit of
the I/O simulator board.

2-3
 St a r t e r K i t M a n u a l

2. Connect a single-phase 110/220 V cable

to the L and N terminals.
Note: To prevent staff from being hurt, the
external AC power which is used should
be switched off before hardware is wired.

_2

3. Use the DC power cable to connect

DVP-PS01 to DVP12SE11R.

4. Use the DC power cable to connect the

digital I/O simulator board to DVP-PS01.

5. Use the DC power cable to connect

DVP-PS01 to DC power input terminals on
DOP-107EV

2-4
 C h a p t e r 2 I n s t a l l a t i o n o f U T S e r i e s St a r t e r K i t s

6. The assembly of the UT-12SE-A1 starter

kit is complete.

2_

2.1.2 Connecting a Personal Computer to DVP14SS211R

Users have to connect a personal computer to DVP14SS211R by means of

UC-RRG020-12A.

PC UC-PRG020-12A(2M) PLC

2.1.3 Connecting a Personal Computer to DOP-107BV

Users have to connect a personal computer to DOP-107BV by means of

UC-PRG015-02A.

UC-PRG015-02A(1.5M)
PC

HMI 1

2-5
 St a r t e r K i t M a n u a l

2.1.4 Connecting DVP14SS211R to DOP-107BV

 RS-232

UC-MS020-06A is used to connect DVP14SS211R to DOP-107BV, and a male-to male

DB9 adapter is used to connect UC-MS020-06A to DOP-107BV.
_2
Model DVP14SS211R DOP-107BV

COM port COM1 (RS-232) COM (RS-232)

Wiring
diagram
UC-MS020-06A(2M) Male DB9

PLC HMI 1

 RS-485

An RS-485 cable can be used to connect the COM port on DOP-107BV to

DVP12SS211R.

Model DVP14SS211R DOP-107BV

COM port COM2 (RS-485) COM (RS-485)

D+: Red
Wiring
diagram D-: Black

RS-485 Cable(1M) Male DB9

PLC HMI 1

2-6
 C h a p t e r 2 I n s t a l l a t i o n o f U T S e r i e s St a r t e r K i t s

2.1.5 Connecting a Personal Computer to DVP12SE11R

Users have to connect a personal computer to DVP12SE11R by means of

UC-PRG015-01A.

2_

UC-PRG015-01A(1.5M)
PC

2.1.6 Connecting a Personal Computer to DOP-107EV

Users have to connect a personal computer to DOP-107EV by means of

UC-PRG015-02A.

UC-PRG015-02A(1.5M)
PC

HMI

2.1.7 Connecting DVP12SE11R to DOP-107EV

 RJ45

The Ethernet cable UC-PRG030-20A is used to connect DVP12SE11R to DOP-107EV.

Model DVP12SE11R DOP-107EV

COM port RJ45 RJ45

Wiring
diagram UC-PRG030-20A(3M)

PLC HMI

2-7
 St a r t e r K i t M a n u a l

 RS-485

An RS-485 cable can be used to connect COM2/COM3 on DOP-107EV to DVP12SE11R.

Model DVP12SE11R DOP-107EV

COM port COM2 (RS-485) COM2/COM3 (RS-485)

_2
D+: Red
Wiring
diagram D-: Black

RS-485 Cable(1M) Male DB9

PLC HMI

2.2 Installing ISPSoft

If an older version of ISPSoft has been installed on a computer, users have to uninstall it
before installing ISPSoft.

Graphic representations

Graphic
Description
representation

Clicking the left mouse button

Clicking the right mouse button

Clicking the left mouse button two times in quick succession

Pressing and holding the left mouse button, and then moving the mouse
without releasing the button

Typing with a keyboard

Operating sequence (The graphic representation is used when an

operating sequence is mentioned, e.g. and .)

Number used to describe a figure

2-8
 C h a p t e r 2 I n s t a l l a t i o n o f U T S e r i e s St a r t e r K i t s

Installing ISPSoft:

(1) Start the operating system installed on a computer. Users have to log on to the
system as a system administrator before they install ISPSoft.

(2) Insert the USB flash drive which is an attachment to a UT series starter kit into the
computer, and then double-click StarterKit.exe in the USB flash drive.
2_

2-9
 St a r t e r K i t M a n u a l

(3) Click Install Software.

_2

(4) Click Install ISPSoft Ver x.xx. (Alternatively, the users can download the
installation program from the official website of Delta http://www.deltaww.com.
(Before the installation program downloaded from the website is installed, it
needs to be decompressed.))

2-10
 C h a p t e r 2 I n s t a l l a t i o n o f U T S e r i e s St a r t e r K i t s

(5) Click Next in the ISPSoft x.xx - InstallShield Wizard window.

2_

(6) Select the I accept the terms in the license agreement option button, and then click
Next.

2 - 11
 St a r t e r K i t M a n u a l

(7) Type related information in the User Name box and the Organization box, and then
click Next.

_2

(8) Check installation settings, and then click Install.

2-12
 C h a p t e r 2 I n s t a l l a t i o n o f U T S e r i e s St a r t e r K i t s

(9) After ISPSoft is installed, shortcuts to the program will be created on the desktop
and the Start menu. Click Finish to complete the installation.

2_

(10) Start ISPSoft. (Click the Start button  All Programs  Delta Industrial

Automation  PLC  ISPSoft x.xx  ISPSoft x.xx, or click on the

desktop.)

2-13
 St a r t e r K i t M a n u a l

2.3 Installing COMMGR

COMMGR is software independent of ISPSoft. It must be installed and uninstalled
separately. If an older version of COMMGR has been installed on a computer, users have
to uninstall it before installing COMMGR.

_2 (1) Start the operating system installed on a computer. Users have to log on to the
system as a system administrator before they install ISPSoft.

(2) Insert the USB flash drive which is an attachment to a UT series starter kit into the
computer, and then double-click StarterKit.exe in the USB flash drive.

2-14
 C h a p t e r 2 I n s t a l l a t i o n o f U T S e r i e s St a r t e r K i t s

(3) Click Install Software.

2_

(4) Click Install COMMGR Ver x.xx. (Alternatively, the users can download the
installation program from the official website of Delta http://www.deltaww.com.
(Before the installation program downloaded from the website is installed, it needs to
be decompressed.))

2-15
 St a r t e r K i t M a n u a l

(5) Click Next in the COMMGR x.xx - InstallShield Wizard window.

_2

(6) Check the settings and click Install.

2-16
 C h a p t e r 2 I n s t a l l a t i o n o f U T S e r i e s St a r t e r K i t s

(7) After COMMGR is installed, a shortcut to the program will be created on the Start
menu. Click Finish to complete the installation.

2_

(8) Start COMMGR. (Click the Start button  All Programs  Delta Industrial
Automation  Communication  COMMGR  COMMGR.)

2-17
 St a r t e r K i t M a n u a l

2.4 Installing DOPSoft

Users have to boot a computer, and log on to Windows 7 as a system administrator.
Before they install DOPSoft, they have to click Control Panel, click User Accounts and
Family Safety, click User Accounts, click Change User Account Control settings,
move the slider all the way down to Never Notify, and click OK.
_2

After the users finish changing User Account Control settings, they can install DOPSoft by
following the instructions below.

2-18
 C h a p t e r 2 I n s t a l l a t i o n o f U T S e r i e s St a r t e r K i t s

(1) Insert the USB flash drive which is an attachment to a UT series starter kit into the
computer, and then double-click StarterKit.exe in the USB flash drive.

2_

(2) Click Install Software.

2-19
 St a r t e r K i t M a n u a l

(3) Click Install DOPSoft Ver x.xx.xx (Alternatively, the users can download the
installation program from the official website of http://www.deltaww.com. (Before the
installation program downloaded from the website is installed, it needs to be
decompressed.))

_2

(4) A dialog box with message of “Do you want to allow this app from an unknown
publisher to make changes to your device?” Click Yes.

2-20
 C h a p t e r 2 I n s t a l l a t i o n o f U T S e r i e s St a r t e r K i t s

(5) Please select a language. The software provides three languages. They are
traditional Chinese, simplified Chinese, and English. The users have to click OK after
they select a language.

2_

(6) Please check whether the DOPSoft checkbox is selected, and then click Install.

2-21
 St a r t e r K i t M a n u a l

(7) After Install is selected, the progress bar which is used to visualize the progression of
the installation of DOPSoft will be displayed.

_2

(8) Click Next in the Device Driver Installation Wizard window.

2-22
 C h a p t e r 2 I n s t a l l a t i o n o f U T S e r i e s St a r t e r K i t s

(9) The Windows Security dialog box appears when the device driver needed is
installed. Please click Install.

2_

(10) Click Finish after the installation of the device driver is complete.

2-23
 St a r t e r K i t M a n u a l

(11) After the installation of DOPSoft is complete, the progress bar will indicate that the
installation of the software is complete. Please click Close to close the installation
screen.

_2

(12) Start DOPSoft. (Click the Start button  All Programs  Delta Industrial

Automation  HMI  DOPSoft x.xx.xx  DOPSoft x.xx.xx, or click on the

desktop.)

2-24
 C h a p t e r 2 I n s t a l l a t i o n o f U T S e r i e s St a r t e r K i t s

2.5 Installing DCISoft

(1) Insert the USB flash drive which is an attachment to a UT series starter kit into the
computer, and then double-click StarterKit.exe in the USB flash drive.

2_

(2) Click Install Software.

2-25
 St a r t e r K i t M a n u a l

(3) Click Install DCISoft Ver. x.xx (UT-12SE-A1). (Alternatively, the users can download
the installation program from the official website of http://www.deltaww.com. (Before
the installation program downloaded from the website is installed, it needs to be
decompressed.))

_2

(4) Click Next in the DCISoft x.xx Setup window.

2-26
 C h a p t e r 2 I n s t a l l a t i o n o f U T S e r i e s St a r t e r K i t s

(5) If the users want to install DCISoft in a different folder, they have to click Browse, and
select another folder. If the users want to install DCISoft in the default folder, they
have to click Install.

2_

(6) After DCISoft is installed, shortcuts to the program will be created on the desktop and
the Start menu. Click Finish to complete the installation.

2-27
 St a r t e r K i t M a n u a l

_2

(7) Start DCISoft. (Click the Start button  All Programs  Delta Industrial

Automation  Communication  DCISoft x.xx  DCISoft x.xx, or click on

the desktop.)

2-28
 C h a p t e r 2 I n s t a l l a t i o n o f U T S e r i e s St a r t e r K i t s

2.6 Installing the UC-PRG020-12A Driver

(1) Insert the USB flash drive which is an attachment to a UT series starter kit into the
computer, and double-click StarterKit.exe in the USB flash drive.

2_

(2) Click Install Software.

2-29
 St a r t e r K i t M a n u a l

(3) Click Install UC-PRG020-12A Driver (UT-14SS2-A) (Alternatively, the users can
download the installation program from the official website of http://www.deltaww.com.
(Before the installation program downloaded from the website is installed, it needs to
be decompressed.))

_2

(4) Click UC-PRG020-12A Driver (32-Bit) or UC-PRG020-12A Driver (64-Bit) according

to the Windows operating system used.

2-30
 C h a p t e r 2 I n s t a l l a t i o n o f U T S e r i e s St a r t e r K i t s

(5) Click Next.

2_

(6) Select the I accept this agreement option button, and then click Next.

2-31
 St a r t e r K i t M a n u a l

_2

(7) Click Finish.

(8) After UC-PRG020-12A is connected to the computer, Silicon Labs CP210x USB to
UART Bridge (COMx) will appear in the Device Manager window. COMx represents
the communication port connected to UC-PRG020-12A.

2-32
 3
Chapter 3 Example Programs

Table of Contents

3.1 Example 1 ...................................................................................... 3-3

3.1.1 Creating a Project for a PLC ..................................... 3-3
3.1.2 Creating a Main Program ......................................... 3-6
3.1.3 Setting COMMGR for UT-14SS2-A............................ 3-15
3.1.4 Downloading a PLC Project ..................................... 3-18
3.1.5 Monitoring a Program ............................................ 3-21
3.1.6 Using a PLC with an I/O Simulator Board ................. 3-23
3.1.7 Writing a Program for an HMI ................................. 3-24
3.1.8 Compiling and Downloading an HMI Program ............ 3-50
3.1.9 Using an HMI with an I/O Simulator Board ............... 3-52

3.2 Example 2 .................................................................................... 3-55

3.2.1 Project Requirements ............................................ 3-55
3.2.2 Project Development ............................................. 3-56
3.2.3 Writing a Program for an HMI ................................. 3-58
3.2.4 Creating a Project for a PLC .................................... 3-80
3.2.5 Setting COMMGR for UT-12SE-A1 ............................ 3-93
3.2.6 Downloading a PLC Project ..................................... 3-96
3.2.7 Setting Ethernet Parameters for DVP12SE11R .......... 3-98

3-1
 3.2.8 Testing a Project ................................................. 3-102

3-2
 Chapter 3 Example Programs

3.1 Example 1
The steps of writing programs in ISPSoft and DOPSoft are described below. After users
follow the steps introduced below, they will know how to write programs for a PLC and an
HMI. The example below is applicable to UT series starter kits. The starter kit used in the
example is UT-14SS2-A.

UC-PRG015-02A(1.5M)

D+: Red

3_
D-: Black

RS-485 Cable(1M) Male DB9

PC
UC-PRG020-12A(2M) PLC HMI 1
UC-MS020-06A(2M) Male DB9

3.1.1 Creating a Project for a PLC

After the users install hardware and understand the control logic in the example, they can
prepare to write a program.

In the example, the PLC used is DVP14SS211R.

Please complete the step in section 2.1.2 before writing the example program shown
below.

Step 1: Start ISPSoft. (Click the Start button  All Programs  Delta Industrial
Automation  PLC  ISPSoft x.xx  ISPSoft x.xx, or click on the

desktop.)

Welcome screen

3-3
 St a r t e r K i t M a n u a l

Main screen

_3

Step 2: After is clicked, a new project will be added. The project name typed in the
Project Name box is “NEW”. Select SS2 in the PLC Type drop-down list box,
leave the default path in the Drive/Path box unchanged, and click OK.

3-4
 Chapter 3 Example Programs

After OK in the Create a New Project window is clicked, a project environment will be
displayed (the project name “NEW” will appear in the upper left corner of the project
environment).

3_

3-5
 St a r t e r K i t M a n u a l

3.1.2 Creating a Main Program

Step 1: Creating a POU

Creating a main program. Right-click in the project management area in

ISPSoft to add a new POU.

Note: Please refer to Chapter 5 in ISPSoft User Manual for more information about
creating a POU.

_3

Type “Prog_Main” in the POU Name box, select Ladder Diagram (LD) in the Language
section, type “Main Program” in the POU Comment box, ,and click OK.

The users can see the Prog_Main window on the main screen.

3-6
 Chapter 3 Example Programs

3_

Step 2: Writing a program

The users can prepare to write a main program. In order to scan a program conveniently,
the users can develop the habit of writing comments. If the users want to write network
comments, they have to click .

Type a comment in the comment box for network 1. If the users want to start a new line of
text at a specific point, they can press Shift+Enter on the keyboard.

The users can begin to edit program code. The programming language used here is a

3-7
 St a r t e r K i t M a n u a l

ladder diagram. Please click , and then move the mouse cursor to the red frame. If
the mouse cursor becomes , the users can click the left mouse button.

_3

Click ???, and type “X0”.

After the users click the line at the right side of the X0 contact, the red frame on the X0
contact will move to the line.

3-8
 Chapter 3 Example Programs

Click , move the mouse cursor to the red frame, and click the left mouse button.

3_
Click ???, and type “Y0”.

Click to add a new network.

Create the following program in the same way.

3-9
 St a r t e r K i t M a n u a l

Click in the project management area in ISPSoft, click Basic Instructions, and
drag CNT to the red frame.

_3

If the users do not know the usage of CNT, they can click the CNT instruction block, press
F1 on the keyboard, and refer to the information in the PLC Instructions and Special
Registers Reference window.

3-10
 Chapter 3 Example Programs

Click ??? in the box at the left side of S1, and type “C0”. Click ??? in the box at the left
side of S2, and type “5”.

3_

Click to add a new network, the input contact C0, and the output coil Y1.

Click to add a new network, and the input contact X2.

3 - 11
 St a r t e r K i t M a n u a l

Type “TMR” directly.

_3

3-12
 Chapter 3 Example Programs

Click to open the API List window. The API List window helps the users edit the
parameters of TMR easily. In the API List window, select T in the S1 drop-down list box,
select K in the S2 drop-donw list box, select 0 in the upper Component Value box, select
50 in the lower Component Value box, and click OK.

3_

After the setting of the parameters of TMR is complete, the program shown below will
appear.

Create the program below.

3-13
 St a r t e r K i t M a n u a l

Step 3: Compiling the program created

The writing of the program will be complete after the users save the file.

The users can click to check the syntax of the program, and click to compile the
project. The compiling of a project is different from the checking of the syntax of a
program in that it is composed of the checking of syntax, and the compiling of all
programs and function blocks.

_3

3-14
 Chapter 3 Example Programs

3.1.3 Setting COMMGR for UT-14SS2-A

Step 1: Start COMMGR. (Click the Start button  All Programs  Delta Industrial
Automation  Communication  COMMGR  COMMGR.)

3_

Step 2: After COMMGR is started, the icon representing COMMGR will appear in the
notification area. Double-click the icon representing COMMGR to open the
COMMGR window.

3-15
 St a r t e r K i t M a n u a l

Step 3: After the COMMGR window is opened, users can begin to set a driver.
UC-RRG020-12A cable is used to connect the computer and a PLC here, and
therefore an RS-232 driver needs to be created. First, click Add. Then, set an
RS-232 driver in the way shown below.

_3

Users can type a driver name in the Driver Name box. Special marks can not be used
except _.

Select RS232 in the Type drop-down list box in the Connection Setup section.
Select an RS- 232 communication port in the COM Port drop-down list box. Each item
in the COM Port drop-down list box is composed of a device name and a
communication port number. The communication ports in the COM Port drop-down list
box are the same as the communication ports in the Device Manager window.

The communication format can be ASCII or RTU.

The communication protocol for exchanging data through a communication port
selected must be the same as the communication protocol for exchanging data through

3-16
 Chapter 3 Example Programs

a communication port on a device connected. If users click Default, all communication

parameters will return to the default values.

If users do not know the communication protocol for exchanging data through a
communication port on a device connected, the users can connect the device to an
RS-232 communication port selected with an RS-232 cable, and click Auto-detect to
automatically detect the communication protocol. If the communication protocol is
detected successfully, the related communication parameters in the Driver Properties
window are set. However, when the communication protocol is detected automatically,
the COM Port parameter and the ASCII/RTU parameter are not detected. As a result,
3_
the users have to set the COM Port parameter and the ASCII/RTU parameter before
clicking Auto-detect.

Users can select the number of times the sending of a command is retried if a
connection error occurs in the Time of Auto-retry box, and select an interval of
retrying the sending of a command in the Time Interval of Auto-retry box.

*. When the Driver Properties window is opened, the information about the
communication ports in the Device Manager window is retrieved once. However, the
information in the COM Port drop-down list box will not be updated. If a device is
added to the computer system after the Driver Properties window is opened, the
device will not be displayed in the COM Port drop-down list box. Users have to close
the Driver Properties window, and open it again.

Step 4: After the setting of an RS-232 driver is complete, the RS-232 driver will appear in
the COMMGR window. If the computer is normally connected to the PLC used,
OK will appear in the Status column.

If the users click or in the COMMGR window, the COMMGR window will
disappear from the desktop, and will be visible only as an icon in the notification area.

3-17
 St a r t e r K i t M a n u a l

3.1.4 Downloading a PLC Project

 Setting communication

After the setting of COMMGR is complete, users can set communication in ISPSoft.
First, click Communication Settings… on the Tools menu to open the
Communication Setting window.

_3

In the Communication Setting window, select RS-232 in the Driver drop-down list
box, and click OK.

The users can see the information about the driver which is connected on the lower
right corner of the status bar.

3-18
 Chapter 3 Example Programs

 Downloading a PLC program

After users write a PLC program, they can prepare to download the program. The
program created here has been compiled. If the program is modified, the users can
click to check the program. After the compiling of the program is successful, the
us ers can click to download the program.

3_

There are several checkboxes in the Transfer Setup window. Object code is a
necessary condition for the operation of a PLC, and therefore the Object Code
checkbox is selected. In order to maintain the program conveniently, the Program
checkbox and the Comments checkbox are selected in this example. The project will
be backed up onto the PLC connected, and the program will not be lost. Besides, if
the users want to modify the program, and forget to bring the program, they can
upload the program from the PLC to the computer to modify the program.

After the users click OK in the Transfer Setup window, the downloading of the
program will be complete.

3-19
 St a r t e r K i t M a n u a l

After the program is downloaded, the users can click if they want to run the PLC.

_3

Alternatively, the users can move the RUN/STOP swithc on the PLC to the RUN
position.

3-20
 Chapter 3 Example Programs

3.1.5 Monitoring a Program

When a program is executed, users can monitor the program to understand the current
logical control state of the system, or modify the values in some devices to test the
system. The monitoring of a program is described below.

 Monitoring a program

Open the Prog_Main window, and click .

3_

After users click , the program will be monitored. The program is composed of a
logic program, and the information about devices. (The states of Boolean devices are
indicated by green backgrounds (On) or white backgrounds (Off), and the information
about other devices is indicated by values or text.)

If a device corresponds to an actual I/O device, Set On and Set Off can not be used
to change the state of the device because the state of the actual I/O device
immediately overwrites the value which is set, and Force On and Force Off can be
used instead. X0 is forced to be On here.

3-21
 St a r t e r K i t M a n u a l

The state of X0 is changed, and a lock symbol indicating that the device is forced to
be On appears.

After the system is tested, the users have to cancel the forced state of the device so
that the PLC can return to normal.
_3

3-22
 Chapter 3 Example Programs

3.1.6 Using a PLC with an I/O Simulator Board

3_

1. If X0 is turned from Off to On, Y0 will be On, and the red light on the I/O simulator
board will be turned On.

2. If X0 is turned from On to Off, Y0 will be Off, and the red light on the I/O simulator
board will be turned Off.

3. If X1 is turned from Off to On five times, C0 will be turned from Off to On, Y1 will be
turned from Off to On, and the yellow light on the I/O simulator board will be turned
On.

4. If X2 is turned from Off to On, T0 will begin to measure time. After the time that T0
measures reaches 5 seconds, T0 will be turned from Off to On, Y2 will be turned from
Off to On, and the green light on the I/O simulator board will be turned On.

5. If X2 is turned from On to Off, T0 will be Off, Y2 will be Off, and the green light on the
I/O simulator board will be tunred Off.

3-23
 St a r t e r K i t M a n u a l

3.1.7 Writing a Program for an HMI

The Delta software which supports DOP-107BV is DOPSoft. Please refer to DOPSoft
User Manual for more information about the usage of DOPSoft.

In the example, the HMI used is DOP-107BV.

Please complete the step in section 2.1.3 before writing the example program shown
below.

Step 1: Start DOPSoft. (Click the Start button  All Programs  Delta Industrial
_3
Automation  HMI  DOPSoft x.xx.xx  DOPSoft x.xx.xx, or click on
the desktop.)

Welcome screen

3-24
 Chapter 3 Example Programs

Main screen

3_

3-25
 St a r t e r K i t M a n u a l

Step 2: After or is clicked, a new project will be added. Select DOP-100

series in the Series drop-down list box, click 107BV on the HMI list, leave the
default project name in the Project Name box unchanged, and click Next.

_3

Step 3: The setting of RS-232 communication and RS-485 communication is described

below.

3-26
 Chapter 3 Example Programs

 RS-232 communication

1. In the Project Wizard window, type “DVP14SS211R” in the Link Name box,
select Delta in the Manufacturers drop-down list box, select Delta DVP PLC in
the Controller drop-down list box, select RS232 in the Interface drop-down list
box, select 7 Bits in the Data Bits drop-down list box, select 1 Bit in the Stop
Bits drop-down list box, select 9600 in the Baud Rate drop-down list box, select
Even in the Parity drop-down list box, select 1 in the PLC Station box, and click
Finish.

3_

2. Setting a communication format for DVP14SS211R:

COM1 is an RS-232 port. The default communication format of COM1 is

described below.

Baud rate: 9600 bps

Data length: 7 data bits

Parity: Even

Stop bit: 1 stop bit

3-27
 St a r t e r K i t M a n u a l

Transmission mode: ASCII

Please refer to section 4.4.3 for more information about setting a communicaiton
format.

Note: If users want to change the default communication format of COM1 on

DVP14SS211R, they have to add the program above to the main program
in DVP14SS211R, and move the RUN/STOP switch on DVP14SS211R to
the RUN position. If the users want to connect a PC to COM1 on
DVP14SS211R, the communication format set in COMMGR needs to be
_3 the same as the communicaiton format of COM1.

3. Please refer to section 2.1.4 for more information about using an RS-232 cable to
connect DVP14SS211R to DOP-107BV.

 RS-485 communication

1. In the Project Wizard window, type “DVP14SS211R” in the Link Name box,
select Delta in the Manufacturers drop-down list box, select Delta DVP PLC in
the Controller drop-down list box, select RS485 in the Interface drop-down list
box, select 7 Bits in the Data Bits drop-down list box, select 1 Bit in the Stop
Bits drop-down list box, select 9600 in the Baud Rate drop-down list box, select
Even in the Parity drop-down list box, select 1 in the PLC Station box, and click
Finish.

3-28
 Chapter 3 Example Programs

3_

2. Setting a communication format for DVP14SS211R:

COM2 is an RS-485 port. The default communication format of COM2 is

described below. If users want to modify the communication format of COM2,
they can refer to section 4.4.3 for more information.

Baud rate: 9600 bps

Data length: 7 data bits

Parity: Even

Stop bit: 1 stop bit

Transmission mode: ASCII

3. Please refer to section 2.1.4 for more information about using an RS-485 cable to
connecting DVP14SS211R to DOP-107BV.

After Finish in the Project Wizard window is clicked, a project environment will be
displayed.

3-29
 St a r t e r K i t M a n u a l

_3

The steps of editing an HMI screen are described below.

Choose Element > Indicator > Multistate Indicator and left-click the mouse to drag and
drop the picture for editing.

3-30
 Chapter 3 Example Programs

3_

Double-click the element to open the Multistate Indicator window.

Set the parameter in the Memory section.

3-31
 St a r t e r K i t M a n u a l

_3

3-32
 Chapter 3 Example Programs

Select 0 in the State drop-down list box, and then set the parameters in the Style section.

3_

3-33
 St a r t e r K i t M a n u a l

Click the Picture tab, select $3DFineSW2State.pib in the Picture Bank Name
drop-down list box, and click SW2State_058.bmp in the Select Picture window.

_3

3-34
Chapter 3 Example Programs

3_

3-35
 St a r t e r K i t M a n u a l

Select 1 in the State drop-down list box, and then set the parameters in the Picture
section.

_3

After OK in the Multistate Indicator window is clicked, the screen shown below will
appear.

3-36
 Chapter 3 Example Programs

Adjust the size of the element.

The editing of the element is complete.

3_

Create a text box.

3-37
 St a r t e r K i t M a n u a l

Double-click the text box to open the Text window. In the Text window, click the Text tab,
and type “X0” in the Text section.

_3

3-38
 Chapter 3 Example Programs

Create the X1 indicator and the X2 indicator shown below in the same way.

3_

Choose Element > Indicator > Multistate Indicator and left-click the mouse to drag and
drop the picture for editing.

3-39
 St a r t e r K i t M a n u a l

_3

3-40
 Chapter 3 Example Programs

Double-click the element to open the Multistate Indicator window. Set the parameter in
the Memmory section in the Multistate Indicator window.

3_

3-41
 St a r t e r K i t M a n u a l

Click the Picture tab, select $3DLamp2State.pib in the Picture Bank Name drop-down
list box, and click Lamp2State_02.bmp in the Select Picture window.

_3

3-42
Chapter 3 Example Programs

3_

3-43
 St a r t e r K i t M a n u a l

Select 1 in the State drop-down list box, click the Picture tab, and set the parameters in
the Picture section.

_3

Adjust the size of the element.

Create the text “Y0”.

3-44
 Chapter 3 Example Programs

Create the Y1 indicator and the Y2 indicator shown below in the same way.

3_

Choose Element > Data Display > Numeric Display and left-click the mouse to drag
and drop the picture for editing.

3-45
 St a r t e r K i t M a n u a l

_3

3-46
 Chapter 3 Example Programs

Double-click the element to open the Numeric Display window.

3_

3-47
 St a r t e r K i t M a n u a l

Set the parameters in the Memmory section, the Style section, and the Detail section.

_3

Create the text “C0”.

3-48
 Chapter 3 Example Programs

Create a numeric display which represents T0 in the same way.

3_

The writing of the program will be complete after the users save the file.

3-49
 St a r t e r K i t M a n u a l

3.1.8 Compiling and Downloading an HMI Program

After the HMI program above is created, users can download it to DOP-107BV. Before
the HMI program created above is downloaded, the users have to compile it. After the
users click Compile on the Tools menu, or click , the HMI program created above will
be compiled, and the information about the result of the compiling of the program will be
displayed in the Output window.

_3

After the users compile the HMI program created above, they can click to donwload
the screen and the recipes in the program.

If the HMI is used for the first time or the firmware of the HMI is old, the firmware of the
HMI will be automatically updated after is clicked. Please see the figure below.

3-50
 Chapter 3 Example Programs

A progress bar appears on the screen of the HMI when the firmware of the HMI is
updated.

3_

3-51
 St a r t e r K i t M a n u a l

After the firmware of the HMI is updated, the HMI will read the data which needs to be
downloaded.

_3
After the downloading of the program is complete, the screen shown below will appear.

3.1.9 Using an HMI with an I/O Simulator Board

1. If X0 is turned from Off to On, Y0 will be On. If X0 is turned from On to Off, Y0 will be
Off.

3-52
Chapter 3 Example Programs

3_

3-53
 St a r t e r K i t M a n u a l

2. If X1 is turned from Off to On five times, C0 will be turned from Off to On, abd Y1 will
be turned from Off to On.

_3

3. If X2 is turned from Off to On, T0 will begin to measure time. After the time that T0
measures reaches 5 seconds, T0 will be turned from Off to On, and Y2 will be turned
from Off to On. If X2 is turned from On to Off, T0 will be Off, and Y2 will be Off.

3-54
 Chapter 3 Example Programs

3.2 Example 2
Generally speaking, there are programmers who are responsible for writing a PLC
program and an HMI program during the process of developing a project. They work
together to meet the requirements of the project.

The example below helps users understand how to writing a PLC program and an HMI
program during the process of developing a project. The starter kit used in the following
example is UT-12SE-A1.

UC-PRG015-02A(1.5M) 3_
D+: Red

D-: Black
RS-485 Cable(1M) Male DB9
UC-PRG015-01A(1.5M)
PC
UC-PRG030-20A(3M)
PLC HMI

3.2.1 Project Requirements

1. There are five rooms, and they are numbered from 101 to 105. If a customer in a
room needs service, the customer can press the call button in the room to call an
attendant. After a call button is pressed, the number of rooms calling will increase by
one.

2. If several rooms call, the display on the service counter will show the number of
rooms calling, and the order in which the rooms call.

3. If an attendant checks a room, and then presses the check button on the display, the
number of rooms calling will decrease by one, and the next room number will be
shown on the display.

4. After all the rooms calling are checked, the number of rooms calling shown on the
display will be 0.

5. After an attendant presses the reset button on the display, all data will be cleared.

3-55
 St a r t e r K i t M a n u a l

Please see the figure below for more information.

R oom No. Rooms

N u m b e r o f r o o m s c a llin g
Room 101 Room102 Room 103 Room 104 Room 105

C he ck Reset

R o o m c a ll c o n t r o l c e n t e r

_3 3.2.2 Project Development

After users understand project requirements, they need to discuss and plan a project. The
project needs to be composed of a PLC program and an HMI program. Besides, the
users have to select PLC devices and HMI elements.

 PLC

1. There are five rooms and five call buttons.

2. The rooms are numbered from 101~105.

3. If an attendant checks a room, and then presses the check button on the display
on the service counter, the number of rooms calling will decrease by one, and the
next room number will be shown on the display.

4. After all the rooms calling are checked, the number of rooms calling shown on the
display on the service counter will be 0.

5. After an attendant presses the reset button on the display, all data will be cleared.

6. Default Ethernet IP address: 192.168.1.5

 HMI

1. The display on the service counter shows a room number.

2. The display on the service counter shows the number of rooms calling.

3. There is one check button.

4. There is one reset button.

5. Default Ethernet IP address: 192.168.1.2

3-56
 Chapter 3 Example Programs

 Devices

PLC device Function HMI element

X0 corresponds to the call button in room 101. X0 will be On

X0 -
if the call button in room 101 is pressed.

X1 corresponds to the call button in room 102. X1 will be On

X1 -
if the call button in room 102 is pressed.

X2 corresponds to the call button in room 103. X2 will be On

X2 -
if the call button in room 103 is pressed.

X3
X3 corresponds to the call button in room 104. X3 will be On
- 3_
if the call button in room 104 is pressed.

X4 corresponds to the call button in room 105. X4 will be On

X4 -
if the call button in room 105 is pressed.

M0 corresponds to the check button on the display on the

M0 Button
service counter. M0 will be On if the check button is pressed.

M1 corresponds to the reset button on the display on the

M1 Button
service counter. M1 will be On if the reset button is pressed.

D0 The value in D0 indicates the number of rooms calling. Numeric display

The values in D1~D5 indicate the rooms which have not

D1~D5 -
been checked.

D10 The value in D10 is a room number stored temporarily. -

The value in D11 indicates the room which is being checked.

D11 Numeric display
(First in, first out)

 The relation between PLC devices and HMI elements is shown below.

Room No. D11 Rooms

N u m b e r o f r o o m s c a llin g D 0
Room 101 Room102 Room 103 Room 104 Room 105
M0 M1
C he ck Reset X0 X1 X2 X3 X4

R o o m c a ll c o n t r o l c e n t e r

3-57
 St a r t e r K i t M a n u a l

3.2.3 Writing a Program for an HMI

In the example, the HMI used is DOP-107EV.

After users discuss device requirements, they have to edit HMI elements.

Please complete the step in section 2.1.6 before writing the example program shown
below.

Planning elements:

 M0: Check button

_3
 M1: Reset button

 D0: The value in D0 indicates the number of rooms calling.

 D11: The value in D11 indicates the room which is being checked.

Step 1: Start DOPSoft. (Click the Start button  All Programs  Delta Industrial

Automation  HMI  DOPSoft x.xx.xx  DOPSoft x.xx.xx, or click on

the desktop.)

Welcome screen

3-58
 Chapter 3 Example Programs

Main screen

3_

Step 2: After or is clicked, a new project will be added. Select DOP-100

series in the Series drop-down list box, click 107EV on the HMI list, leave the
default project name in the Project Name box unchanged, and click Next.

3-59
 St a r t e r K i t M a n u a l

_3

Step 3: The setting of Ethernet communication and RS-485 communication is described

below.

 Ethernet communication

1. Setting a communication format for DOP-107EV:

Click Ethernet, and then create a connection.

3-60
 Chapter 3 Example Programs

3_

Type the link name “DVP_SE”, type “192.168.1.5 in the Controller IP box, select
502 in the Port box, and set the parameters in the Main section.

3-61
 St a r t e r K i t M a n u a l

Click the Local Host tab, type “192.168.1.2” in the HMI IP Address box, type
“255.255.255.0” in the Subnet Mask box, type “192.168.1.1” in the Gateway IP
box, and click Finish.

_3

2. Setting a communication format for DVP-12SE11R:

Start DCISoft, and click Communication Setting on the Tools menu to open the
Communication Setting window. Users can select RS232 or Ethernet in the
Communication Type drop-down list in the Communication Setting window.

3-62
 Chapter 3 Example Programs

3_

A. Using the USB port on DVP12SE11R

Before users use UC-PRG015-01A to connect the USB port on

DVP12SE11R to a USB port on a PC, they have to select a COM port for the
USB driver created for DVP12SE11R in COMMGR.

Then, the users have to select RS232 in the Communication Type

drop-down list in the Communication Setting window in DCISoft. The COM

3-63
 St a r t e r K i t M a n u a l

port selected in the COM Port drop-down list box in the Protocol section
needs to be the same as the COM port selected for the USB driver created
for DVP12SE11R in COMMGR.

_3

B. Using the Ethernet port on DVP12SE11R

UC-PRG030-20A can be used to connect the Ethernet port on DVP12SE11R

to an Ethernet port on a PC.

In the Communication Setting window in DCISoft, select Ethernet in the

Communication Type drop-down list box, leave the default IP address in the
Assign IP Address section unchanged, and click OK.

Click after the setting of the parameters in the Communication Setting

window is complete.

3-64
Chapter 3 Example Programs

3_

3-65
 St a r t e r K i t M a n u a l

_3

Double-click the module in DCISoft to open the DVP12SE window.

Click the Basic tab in the DVP12SE window, set the parameters in the
Network Setup section, and click OK.

3-66
 Chapter 3 Example Programs

3_
3. Please refer to section 2.1.7 for more information about using the Ethernet cable
UC-PRG030-20A to connecting DVP12SE11R to DOP-107EV.

 RS-485 communication

1. In the Project Wizard window, type “DVP12SE11R” in the Link Name box, select
Delta in the Manufacturers drop-down list box,select Delta DVP PLC in the
Controller drop-down list box, select RS485 in the Interface drop-down list box,
select 7 Bits in the Data Bits drop-down list box, select 1 Bit in the Stop Bits
drop-down list box, select 9600 in the Baud Rate drop-down list box, select Even
in the Parity drop-down list box, select 1 in the PLC Station box, and click
Finish.

3-67
 St a r t e r K i t M a n u a l

_3

Setting a communication format for DVP12SE11R:

COM2 and COM3 on DVP12SE11R are RS-485 ports. The default

communication formats of COM2 and COM3 are described below.

Baud rate: 9600 bps

Data length: 7 data bits

Parity: Even

Stop bit: 1 stop bit

Transmission mode: ASCII

2. Please refer to section 2.1.7 for more information about using an RS-485 cable to
connecting DVP12SE11R to DOP-107EV.

3-68
 Chapter 3 Example Programs

Editing a screen:

Choose Element > Data Display > Numeric Display and left-click the mouse to drag
and drop the picture for editing.

3_

Double-click the element to open the Numeric Display window.

3-69
 St a r t e r K i t M a n u a l

_3

3-70
 Chapter 3 Example Programs

Set the parameter in the Memory section in the Numeric Display window.

3_

3-71
 St a r t e r K i t M a n u a l

Set the parameters in the Style section and the Detail section.

_3

Click the Text tab, and then set the parameters in the Text section.

3-72
 Chapter 3 Example Programs

After OK in the Numeric Display window is clicked, the numeric display shown below will
appear.

Create the text “Number of rooms calling”.

Create a numeric display correpsonding to D11.

3_

Choose Element > Button > Momentary and left-click the mouse to drag and drop the
picture for editing.

3-73
 St a r t e r K i t M a n u a l

Double-click the element to open the Momentary window.

_3

Set a write address in the Memory section.

3-74
 Chapter 3 Example Programs

3_

Set a read address in the Memory section in the same way.

3-75
 St a r t e r K i t M a n u a l

Click the Text tab, type “Check” in the Language 1 cells, and set a text format.

_3

Select 0 in the State drop-down list box, click the Picture tab, and set the parameters in
the Picture section.

3-76
 Chapter 3 Example Programs

3_

Select 1 in the State drop-down list box, and set the parameters in the Picture section.

3-77
 St a r t e r K i t M a n u a l

_3

Click OK in the Momentary window.

3-78
 Chapter 3 Example Programs

Adjust the size of the element.

Create a reset button in the same way.

3_

After the screen is beautified, the users can get the screen shown below.

3-79
 St a r t e r K i t M a n u a l

3.2.4 Creating a Project for a PLC

In the example, the PLC used is DVP12SE11R.

Please complete the step in section 2.1.5 before writing the example program shown
below.

After users discuss control requirements, they have to write a PLC program.

Planning hardware

After a project is created, the users can plan hardware. The hardware which needs to be
_3
planned for the example is described below.

 Call button in room 101~room 105  X0~X4

 Check button  M0

 Reset button  M1

 Indicating the number of rooms calling  D0

 Indicating the rooms which have not been checked  D1~D5

 Room number stored temporarily  D10

 Indicating the room which is being checked (First in, first out)  D11

 X0~X4 can be used with the I/O simulator board.

Creating global symbols

In order to make a program more readable and the connection to a SCADA system more
convenient, I/O addresses are generally assigned global symbols. Users can use
symbols when they write a program. Besides, a global symbol table can be
imported/exported. If a medium-sized/large-sized system which is equipped with many
inputs and outputs is used, users can use Microsoft Excel to make the editing of a
program for the system more convenient.

3-80
 Chapter 3 Example Programs

The global symbols which need to be created for the example are listed below.

Global symbol table

Hardware points (for inputs/outputs in a PLC)

Address Identifier Data type

X0 Room101 BOOL

X1 Room102 BOOL

X2 Room103 BOOL
3_
X3 Room104 BOOL

X4 Room105 BOOL

M0 Check_Button BOOL

M1 Reset_Button BOOL

D0 Number_of_Rooms_Calling WORD

D11 Displaying_Room_Number WORD

Double-click in the project management area in ISPSoft to open the

Global Symbols window.

3-81
 St a r t e r K i t M a n u a l

Double-click the blank to open the Add Symbol window. Type “Room101” in the
Identifier box, type “X0” in the Address box, type a comment in the Comment… box,
leave the default values in the Type… box and the Initial box unchanged, and click OK.

_3

The users can see a new piece of data in the Global Symbols window.

The users can create the data in the global symbol table above in the Global Symbols
window in the same way.

3-82
 Chapter 3 Example Programs

Creating a main program

After users create global symbols, they can create a main program. Right-click
in the project management area in ISPSoft to add a new POU.

3_

Type “Prog_Main” in the POU Name box, type “Main Program” in the POU Comment box,
and click OK.

3-83
 St a r t e r K i t M a n u a l

Step 1: Edit call buttons and corresponding room numbers. The number corresponding to
the room which calls is stored in D10 temporarily.

Create a call button corresponding to room 101.

After the call button is pressed, the room number corresponding to the button will be sent
_3
to the service counter instantly. Therefore, the contact created is rising edge-triggered.

3-84
 Chapter 3 Example Programs

Write the program shown below.

3_

Step 2: Room numbers are stored in D1~D5 according the order in which the rooms
corresponding to the room numbers call.

The instructions SFWR and SFRD are used to implement FIFO. In this project, the room
which calls first is checked first. FIFO is an acronym for First In, First Out.

3-85
 St a r t e r K i t M a n u a l

Notes:

 The usage of SFWR is described below.

S: Source device
D: Head address of a data stack
n: Length of a data stack
1. The value in a source device S is written to a FIFO data stack. The position of
insertion into the stack is automatically calculated by the PLC used.
_3
2. The instruction defines the values in the n word devices starting from D as a FIFO
data stack, and designate D as a pointer.

3. If SFWR is executed, the value in the pointer D will increase by one, and the value in
S will be written to the device designated by the pointer D. If the value in the pointer D
exceeds n-1, the execution of the instruction will stop, and the carry flag M1022 will
be On.

4. This instruction can be used with SFRD for the reading/writing of a FIFO data stack.

5. Example:

 After X0 is turned from Off to On, the value in the pointer D0 will become 1, and
the value in D20 will be written to D1. If the value in D20 is changed, and X0 is
turned from Off to On again, the value in the pointer D0 will become 2, and the
value in D20 will be written to D2.

 If SFWR is executed once, the writing of a value will follow the steps ~.

 The value in D20 is sent to D1.

 The value in D0 becomes 1.

3-86
 Chapter 3 Example Programs

Source
n=10
D20 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0
Pointer

D0= 3 2 1

 The usage of SFRD is described below.

S: Head address of a data stack

D: Destination device
n: Length of a data stack
3_
1. The source device S is the head address of a FIFO data stack. Its value indicates the
last entry added to a FIFO data stack.

2. If SFRD is executed, the value in S+1 will be moved to D, the values in S+n-1~S+2
will be moved to S+n-2~S+1, and the value in S will decrease by one.

3. If the value in the pointer S is 0, the execution of the instruction will stop, and the
carry flag M1022 will be On.

4. Example:

 After X0 is turned from Off to On, the value in D1 will be sent to D21, the values in
D9~D2 will be moved to D8~D1 (the value in D9 will be unchanged), and the
value in D0 will decrease by one.

 If SFRD is executed once, the reading of a value will follow the steps ~.

 The value in D1 is sent to D21.

 The values in D9~D2 are moved to D8~D1.

 The value in D0 decreases by one.

n=10
D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 D21

Pointer

The value in D1 is read.

3-87
 St a r t e r K i t M a n u a l

After Room101 is turned from Off to On, SFWR will be used to send the room number
101 to Number_of_Rooms_Calling. (D0 functions as a pointer. After SFWR is executed,
the value in D0 will become 1, and the value in D10 (the value 101) will be written to D1.)

_3 Click , and move the mouse cursor to the position under the contact marked with
“Room101”. After the mouse cursor becomes , the users have to click the left mouse
button, type “Room102” in ???, and change the contact added into a rising edge-triggered
contact.

3-88
 Chapter 3 Example Programs

After Room102 is turned from Off to On, SFWR will be used to send the room number
102 to Number_of_Rooms_Calling. (D0 functions as a pointer. After SFWR is executed,
the value in D0 will become 2, and the value in D10 (the value 102) will be written to D2.)

Write the following program. Room numbers are stored in D1~D5 according the order in
which the rooms corresponding to the room numbers call, and the number of rooms
calling is stored in Number_of_Rooms_Calling.

3_

Step 3: Use SFRD to display a room number.

After an attendant presses the check button on the display on the service counter, a room
number will be sent to Displaying_Room_Number, and the value in
Number_of_Rooms_Calling will decrease by one.

3-89
 St a r t e r K i t M a n u a l

Step 4: Create a reset button.

After the reset button on the display on the service counter is pressed, the values in
Number_of_Rooms_Calling, D1~D5, and Displaying_Room_Number will be cleared.

Click , move the mouse cursor to the red frame, and click the left mouse button.

_3

Type “Displaying_Room_Number” in ???, and change the output coil into a reset coil.

3-90
 Chapter 3 Example Programs

The complete program is shown below.

3_

3-91
 St a r t e r K i t M a n u a l

_3

3-92
 Chapter 3 Example Programs

The writing of the program will be complete after the users save the file.

The users can click to check the syntax of the program, and click to compile the
project. The compiling of a project is different from the checking of the syntax of a
program in that it is composed of the checking of syntax, and the compiling of all
programs and function blocks.

3_

3.2.5 Setting COMMGR for UT-12SE-A1

Step 1: Start COMMGR. (Click the Start button  All Programs  Delta Industrial
Automation  Communication  COMMGR  COMMGR.)

3-93
 St a r t e r K i t M a n u a l

Step 2: After COMMGR is started, the icon representing COMMGR will appear in the
notification area. Double-click the icon representing COMMGR to open the
COMMGR window.

_3

3-94
 Chapter 3 Example Programs

Step 3: After the COMMGR window is opened, users can begin to set a driver. A USB
cable is used to connect the computer and DVP12SE11R here, and therefore a
USB driver needs to be created. First, click Add. Then, create a USB driver in the
way shown below.

3_

Step 4: After a USB driver is created, it will appear in the COMMGR window. If the
computer is normally connected to DVP12SE11R, OK will appear in the Status
column.

If the users click or in the COMMGR window, the COMMGR window will
disappear from the desktop, and will be visible only as an icon in the notification area.

3-95
 St a r t e r K i t M a n u a l

3.2.6 Downloading a PLC Project

 Setting communication

After the setting of COMMGR is complete, users can set communication in ISPSoft.
First, click Communication Settings… on the Tools menu to open the
Communication Setting window.

_3

In the Communication Setting window, select SE_USB in the Driver drop-down list
box, and click OK.

The users can see the information about the driver which is connected on the lower
right corner of the status bar.

3-96
 Chapter 3 Example Programs

 Downloading a PLC program

After users write a PLC program, they can prepare to download the program. The
program created here has been compiled. If the program is modified, the users can
click to check the program. After the compiling of the program is successful, the
users can click to download the program.

3_

There are several checkboxes in the Transfer Setup window. Object code is a
necessary condition for the operation of a PLC, and therefore the Object Code
checkbox is selected. In order to maintain the program conveniently, the Program
checkbox and the Comments checkbox are selected in this example. The project will
be backed up onto the PLC connected, and the program will not be lost. Besides, if
the users want to modify the program, and forget to bring the program, they can
upload the program from the PLC to the computer to modify the program.

After the users click OK in the Transfer Setup window, the downloading of the
program will be complete.

3-97
 St a r t e r K i t M a n u a l

3.2.7 Setting Ethernet Parameters for DVP12SE11R

After programs are created, DVP12SE11R can communicate with DOP-107EV through
Ethernet. Users have to set Ethernet parameters for DVP12SE11R. The use of DCISoft to
set Ethernet parameters for DVP12SE11R is described below.

UC-PRG015-01A is used to connect a PC to DVP12SE11R, and DCISoft is used to set

Ethernet parameters.

Step 1: Start DCISoft, and click Communication Setting on the Tools menu to open the
Communication Setting window.
_3

3-98
 Chapter 3 Example Programs

Step 2: The driver created for DVP12SE11R in COMMGR is a USB driver, but the
communication type selected in the Communication Type drop-down list box in
the Communication Setting window needs to be RS232. The COM port
selected in the COM Port drop-down list box needs to be the same as the COM
port selected for the USB driver created for DVP12SE11R in COMMGR.

3_

Step 3: Click after the setting of the parameters in the Communication Setting
window is complete.

3-99
 St a r t e r K i t M a n u a l

_3

3-100
 Chapter 3 Example Programs

Step 4: Double-click the module in DCISoft to open the DVP12SE window.

3_

Step 5: Click the Basic tab in the DVP12SE window, set the parameters in the Network
Setup section, and click OK.

3-101
 St a r t e r K i t M a n u a l

3.2.8 Testing a Project

After users write a PLC program and an HMI program, they can use UC-PRG030-20A to
connect DVP12SE211R to DOP-107EV, and then test the system.

_3

The functions which need to be tested are as follows.

1. Checking whether the room number dipslayed is correct

2. Checking whether the number of rooms calling is correct

3. Checking whether the the funciton of the check button is correct

4. Checking whether the function of the reset button is correct

After the functions listed above are tested, the programs created will be complete.

3-102
 4
Chapter 4 Appendix

Table of Contents

4.1 Introduction of Hardware ........................................... 4-3

4.1.1 DVPPS01 ............................................................... 4-3
4.1.2 DVP14SS211R ........................................................ 4-3
4.1.3 DVP12SE11R.......................................................... 4-3
4.1.4 DOP-107BV............................................................ 4-4
4.1.5 DOP-107EV ............................................................ 4-4

4.2 Profiles and Dimensions .............................................. 4-5

4.2.1 DVPPS01 ............................................................... 4-5
4.2.2 DVP14SS211R ........................................................ 4-5
4.2.3 DVP12SE11R.......................................................... 4-7
4.2.4 DOP-107BV............................................................ 4-8
4.2.5 DOP-107EV ............................................................ 4-9

4.3 Connecting Communication Cables ........................... 4-10

4.3.1 Pin Definitions of Serial Communication .................... 4-10
4.3.2 Introduction of Communication Cables ..................... 4-12

4.4 Communication between a PLC and an HMI .............. 4-14

4.4.1 Wiring a Controller ................................................. 4-14

4-1
 4.4.2 PLC Device Addresses ............................................ 4-15
4.4.3 Setting the Communication Parameters in a PLC ........ 4-18
4.4.4 Setting the Communication Parameters in an HMI...... 4-21

4.5 Equivalent Circuit of an I/O Simulator Board ............ 4-23

4.5.1 Connecting to DVP14SS211R .................................. 4-23
4.5.2 Connecting to DVP12SE11R .................................... 4-24

4.6 Installing the DVP12SE11R Driver ............................ 4-25

4-2
 Chapter 4 Appendix

4.1 Introduction of Hardware

4.1.1 DVPPS01

DVPPS01 is the best choice for DVP series PLCs. It supplies offer
users 24VDC and 24W power with enhanced safety and efficiency.

4.1.2 DVP14SS211R _4

DVP14SS211R is a PLC equipped with eight digital inputs and six

digital outputs. It offers various instructions. The size of the program
memory in it is 8K steps. DVP14SS211R is small in size, and can be
installed easily. It has an RS-232 port and an RS-485 port.

DVP14SS211R can be applied to spinning machines, conveyor belts

(rotational speed control), and winding machines (tension control).

4.1.3 DVP12SE11R

DVP12SE11R is a PLC equipped with eight digital inputs and four digital
outputs. It offers various instructions. The program memory in it is 16K
steps. DVP12SE11R has a mini USB port, an Ethernet port, and two
RS-485 ports. It supports DVP-S series left-side and right-side
modules.

DVP12SE11R can be applied to remote device monitoring, production

line monitoring, building automation, printing machines, and container
fillers (recipe application).

4-3
 St a r t e r K i t M a n u a l

4.1.4 DOP-107BV

Specifications:

 7-inch TFT LCD (800×480 pixels and 65536

colors)

 There is one COM port. It supports RS-232,

RS-422, and RS-485.

 Data can be transmitted/downloaded by

means of RS-232 or USB.

 Degree of resistance to water: IP65/NEMA4

_4
4.1.5 DOP-107EV

Specifications:

 7-inch TFT LCD (800×480 pixels and 65536

colors)

 There are two COM ports. They support

RS-232, RS-422, and RS-485.

 Data can be transmitted/downloaded by

means of RS-232, USB, or Ethernet.

 It has a USB host, and can be directly

connected to a USB disk, a printer, or a
mouse.

 It supports Ethernet.

 Degree of resistance to water: IP65 /

NEMA4 / UL TYPE 4X

 It supports horizontal/vertical display.

4-4
 Chapter 4 Appendix

4.2 Profiles and Dimensions

4.2.1 DVPPS01

 Profile
6

5 2

4
90

3 3
3
36.5 13. 3 60
_4
U nit : mm

1. POWER LED indicator 2. Input/Output terminals (Fixed terminal block)

3. DIN rail clip 4. DIN rail groove (35 mm)

5. Input/Output terminal names 6. Nameplate

4.2.2 DVP14SS211R

 Profile
7
25 .2 5 60
3
1 8

2 6 9
12
10

90 13
11
3
14
4
4

Un it : mm

1. POWER LED indicator, RUN LED indicator,

2. RUN/STOP switch
and ERROR LED indicator

4-5
 St a r t e r K i t M a n u a l

3. COM1 (RS-232 port) 4. DIN rail clip

5. Input/Output terminals 6. Input/Output point indicators

7. Mounting hole 8. Nameplate

9. Extension port 10. DIN rail groove (35 mm)

11. I/O module clip 12. COM2 (RS-485 port)

13. I/O module groove 14. DC power input

 I/O configuration

Input Output I/O configuration

Model
Point Type Point Type Relay

_4 S/S
X0
X1
X2
X3
X4
X5
X6
DC X7
DVP14SS211R 8 6 Relay
(Sink or source) C0
Y0
Y1
Y2

C1
Y3
Y4
Y5

4-6
 Chapter 4 Appendix

4.2.3 DVP12SE11R

 Profile
1
16 8 3 7.4 60
4 8
3
13
2 P OW E R s
s 5 9
R UN
X0
X0
ER R O R
X1
X1

3
C O M1
X2

X3
X2 14
X3
X4
R UN
X5
X4
X5
10
X6
X6
STOP X7

90 C0
X7
11 15
Y0
D VP -12S E
Y0
6 CO M 1 Y1
Y2
Y3
Y1 12
●

12 C O M 3+
SG
Y2

Y3
COM3 -

7
COM 2
COM 3

Et h e r n e t

Un it : mm _4

1. POWER indicator, RUN indicator, ERROR

2. RUN/STOP switch
indicator, COM1 indicator

3. COM1 (Mini USB) 4. Input/Output terminals, COM3 (RS-485)

5. Input/Output point indicators, COM2 indicator,

6. Ethernet port
COM3 indicator

7. DIN rail clip 8. Mounting hole

9. Nameplate 10. Right-side extension port

11. DIN rail groove (35 mm) 12. I/O module clip

13. COM2 (RS-485) 14. I/O module groove

15. DC power input 16. Left-side extension port

4-7
 St a r t e r K i t M a n u a l

 I/O configuration

Input Output I/O configuration

Model
Point Type Point Type Relay

S/ S
X0
X1
X2
X3
X4
X5
X6
DC X7
DVP12SE11R 8 4 Relay
C0
(Sink or source)
Y0
Y1
Y2
Y3

_4 SG
C OM3 +
C OM3 -

4.2.4 DOP-107BV

 Profile
196.9

1 26.2
215 1.6~6
3 2
142.9 4
4
5
161

Unit : mm

1. Touchscreen/Display 2. Power input terminals

3. USB slave 4. USB host

5. COM port

4-8
 Chapter 4 Appendix

4.2.5 DOP-107EV

 Profile
196.9

1 51.2
215 4
142.9 1.6~6
2
5
6
161 142.3 7
2 3 8

U nit: mm

1. Touchscreen/Display 2. COM2
_4

3. Power input terminals 4. Battery Case

5. USB host 6. USB slave

7. Ethernet interface (LAN) 8. COM1

4-9
 St a r t e r K i t M a n u a l

4.3 Connecting Communication Cables

4.3.1 Pin Definitions of Serial Communication

 Definitions of the pins in the COM port on DOP-107BV

Mode 1 Mode 2 Mode 3

COM2 Pin COM1 COM2 COM1 COM2 COM1 COM2

RS-232 RS-485 RS-485 RS-485 RS-232 RS-422

1 D+ TXD+

2 RXD RXD

_4 3 TXD TXD

4 D+ D+ RXD+

5 GND GND GND

6 D- TXD-

7 RTS RTS

8 CTS CTS

9 D- D- RXD-

Note: Blank = No Connection.

4-10
 Chapter 4 Appendix

 Definitions of the pins in the COM ports on DOP-107EV

1. Definitions of the pins in COM1 (supporting flow control)

COM1 Pin RS-232

1
PIN1
2 RXD

3 TXD

5 GND

7 RTS
_4
8 CTS

2. Definitions of the pins in COM2

Mode 1 Mode 2 Mode 3

COM2 Pin COM2 COM3 COM2 COM3 COM2 COM3

RS-232 RS-485 RS-485 RS-485 RS-232 RS-422

1 D+ TXD+

2 RXD RXD

3 TXD TXD

4 D+ D+ RXD+

5 GND GND GND

6 D- TXD-

7 RTS RTS

8 CTS CTS

9 D- D- RXD-

Note: Blank = No Connection.

4 - 11
 St a r t e r K i t M a n u a l

4.3.2 Introduction of Communication Cables

 UC-PRG020-12A (3 m): (Accessory: Male-to-male DB9 adapter)

8-pin male mini-DIN connector ↔ USB connector

8-pin m ale m ini-DIN c onnec tor USB c onnec tor

8 5 1: +5 V(R ED )
2
2: D -(WHITE)
4: Rx
7 4 3: D +(GREEN)
5: T x
8: G ND 4: G ND (BLAC K)
6 1
3

_4 Female DB9 connector ↔ USB connector

Fem ale D B9 c onnec tor USB c onnec tor

9 5 2 : Tx 1: +5 V(R ED )
3: Rx 2: D -(W HITE)
5 : G ND 3: D +(GREEN )
7 : C TS 4: G ND (BLAC K)
6 1 8 : R TS

 UC-PRG015-01A (1.5 m)

Mini USB ↔ USB A Type

5 4

1 1

Mini U SB USB A Type

+5 V(RED): 1 1: +5 V(R ED )
D-(WHITE): 2 2: D -(W HITE)
D+(GR EEN ): 3 3: D +(GREEN )
GN D(BL ACK): 5 4: G ND (BLAC K)

 UC-PRG015-02A (1.5 m)

USB B Type ↔ USB A Type

4-12
 Chapter 4 Appendix

2 3
4

1 4 1

U SB B Type USB A Ty pe

+5V(R ED ): 1 1: + 5V(R ED)

D-(WHITE): 2 2: D -(WHITE)
D+(GREEN): 3 3: D +(GREEN)
GN D(BLACK): 4 4: G ND (BL AC K)

 UC-PRG030-20A (3 m)

RJ45 ↔ RJ45

1 8

8 1

R J4 5 RJ 45
1: T x+ 1: T x+
_4
2: T x- 2: T x-
3: R x+ 3 : R x+
6: R x- 6 : R x-

 UC-MS020-06A (2M)

8-pin male mini-DIN connector ↔ Male DB9 connector

8-pin m ale m ini-DIN c onnec tor Ma le DB 9 conne ctor

8 5 Rx: 4 3 : Tx 9 5
2
Tx: 5 2: Rx
7 4 GND : 8 5 : GN D
5V: 1 , 2 7
6 1 8
3 6 1
1
4
6

4-13
 St a r t e r K i t M a n u a l

 RS-485 cable (1 m)

RS-485 ↔ Male DB9 connector

RED

BL ACK

RS-4 85 Ma le DB 9 conne ctor

9 5
RED 1: D+
BL ACK 6: D-

6 1

4.4 Communication between a PLC and an HMI

_4 4.4.1 Wiring a Controller
 RS-232

DOP series PLC - DVP series

9-pin male D-sub (RS-232) connector 8-pin male mini-DIN (RS-232) connector

RXD (2) (5) TXD

TXD (3) (4) RXD

GND (5) (8) GND

 RS-485

DOP series PLC - DVP series

9-pin male D-sub (RS-485) connector RS-485 terminal

D+ (1) D+ (Red)

D- (6) D- (Black)

4-14
 Chapter 4 Appendix

4.4.2 PLC Device Addresses

Effective range Modbus

DVP address
Device Range Type address
(Hexadecimal)
DVP14SS211R DVP12SE11R (Decimal)

S 000~255 Bit 0000~00FF 000001~000256

S 256~511 Bit 0100~01FF 000257~000512

000~1023
S 512~767 Bit 0200~02FF 000513~000768

S 768~1023 Bit 0300~03FF 000769~001024

X 000~377 (Octal) Bit 000~377 0400~04FF 101025~101280

Y 000~377 (Octal) Bit 000~377 0500~05FF 001281~001536

Bit 000~255 0600~06FF 001537~001792 _4

T 000~255
Word 000~255 0600~06FF 401537~401792

M 000~255 Bit 0800~08FF 002049~002304

M 256~511 Bit 0900~09FF 002305~002560

M 512~767 Bit 0A00~0AFF 002561~002816

0000~4095
M 768~1023 Bit 0B00~0BFF 002817~003072

M 1024~1279 Bit 0C00~0CFF 003073~003328

M 1280~1535 Bit 0D00~0DFF 003329~003584

M 1536~1791 Bit B000~B0FF 045057~045312

M 1792~2047 Bit B100~B1FF 045313~045568

M 2048~2303 Bit B200~B2FF 045569~045824

M 2304~2559 Bit B300~B3FF 045825~046080

M 2560~2815 Bit 0000~4095 B400~B4FF 046081~046336

M 2816~3071 Bit B500~B5FF 046337~046592

M 3072~3327 Bit B600~B6FF 046593~046848

M 3328~3583 Bit B700~B7FF 046849~047104

M 3584~3839 Bit B800~B8FF 047105~047360

4-15
 St a r t e r K i t M a n u a l

Effective range Modbus

DVP address
Device Range Type address
(Hexadecimal)
DVP14SS211R DVP12SE11R (Decimal)

M 3840~4095 Bit 0000~4095 B900~B9FF 047361~047616

Bit 000~199 0E00~0EC7 003585~003784

0~199 16-bit
Word 000~199 0E00~0EC7 403585~403784
C
Bit 200~255 0EC8~0EFF 003785~003840
200~255 32-bit
Dword 200~255 0EC8~0EFF 403785~403840

D 000~255 Word 1000~10FF 404097~404352

D 256~511 Word 1100~11FF 404353~404608

D 512~767 Word 1200~12FF 404609~404864

_4
D 768~1023 Word 1300~13FF 404865~405120

D 1024~1279 Word 1400~14FF 405121~405376

D 1280~1535 Word 1500~15FF 405377~405632

D 1536~1791 Word 1600~16FF 405633~405888

D 1792~2047 Word 1700~17FF 405889~406144

D 2048~2303 Word 1800~18FF 406145~406400

0000 0000
D 2304~2559 Word 1900~19FF 406401~406656
~ ~
D 2560~2815 Word 1A00~1AFF 406657~406912
4999 11999
D 2816~3071 Word 1B00~1BFF 406913~407168

D 3072~3327 Word 1C00~1CFF 407169~407424

D 3328~3583 Word 1D00~1DFF 407425~407680

D 3584~3839 Word 1E00~1EFF 407681~407936

D 3840~4095 Word 1F00~1FFF 407937~408192

D 4096~4351 Word 9000~90FF 436865~437120

D 4352~4607 Word 9100~91FF 437121~437376

D 4608~4863 Word 9200~92FF 437377~437632

D 4864~5119 Word 9300~93FF 437633~437888

4-16
 Chapter 4 Appendix

Effective range Modbus

DVP address
Device Range Type address
(Hexadecimal)
DVP14SS211R DVP12SE11R (Decimal)

D 5120~5375 Word 9400~94FF 437889~438144

D 5376~5631 Word 9500~95FF 438145~438400

D 5632~5887 Word 9600~96FF 438401~438656

D 5888~6143 Word 9700~97FF 438657~438912

D 6144~6399 Word 9800~98FF 438913~439168

D 6400~6655 Word 9900~99FF 439169~439424

D 6656~6911 Word 9A00~9AFF 439425~439680

D 6912~7167 Word 9B00~9BFF 439681~439936

_4
D 7168~7423 Word 9C00~9CFF 439937~440192

D 7424~7679 Word 9D00~9DFF 440193~440448

0000
D 7680~7935 Word N/A ~ 9E00~9EFF 440449~440704
11999
D 7936~8191 Word 9F00~9FFF 440705~440960

D 8192~8447 Word A000~A0FF 440961~441216

D 8448~8703 Word A100~A1FF 441217~441472

D 8704~8959 Word A200~A2FF 441473~441728

D 8960~9215 Word A300~A3FF 441729~441984

D 9216~9471 Word A400~A4FF 441985~442240

D 9472~9727 Word A500~A5FF 442241~442496

D 9728~9983 Word A600~A6FF 442497~442752

D 9984~9999 Word A700~A7FF 442753~443008

D 10000~11999 Word A710~AEDF 442767~44768

4-17
 St a r t e r K i t M a n u a l

4.4.3 Setting the Communication Parameters in a PLC

Function COM port

Number Port
COM1 COM2 COM3
Item

Communication format D1036 D1120 D1109

Retaining communication settings M1138 M1120 M1136

ASCII (Off)/RTU (On) M1139 M1143 M1320

Slave communication address D1121 D1255

Description:
_4
COM1 is an RS-232 port, COM2 is an RS-485 port, and COM3 is an RS-485 port. They
support Modbus ASCII/RTU communication. If RTU communication is selected, the data
length selected should be 8 bytes. COM2 and COM3 support data rates up to 921 kbps.
COM1, COM2, and COM3 can be used at the same time. If the communication port used
is a USB port, it can not function as a master.

COM1:

COM1 can function as a master or a slave. It supports ASCII/RTU communication and

data rates upt to (115200 bps). Besides, it can be used to change the number of data bits,
a parity bit, and the number of stop bits.

D1036: Master/Slave communication protocol used by COM1 (Bit 8~bit 15 are not used.
Please refer to the table below for more information.)

COM2:

COM2 can function as a master or a slave. It supports ASCII/RTU communication and

data rates upt to (921 kbps). Besides, it can be used to change the number of data bits, a
parity bit, and the number of stop bits.

D1120: Master/Slave communication protocol used by COM2 (Please refer to the table
below for more information.)

4-18
 Chapter 4 Appendix

COM3:

COM3 can function as a master or a slave. It supports ASCII/RTU communication and

serial transmission speed upt to (921 kbps). Besides, it can be used to change the
number of data bits, a parity bit, and the number of stop bits.

D1109: Master/Slave communication protocol used by COM3 (Bit 8~bit 15 are not used.
Please refer to the table below for more information.)

 Communication protocol

Contents

0: 7; 1: 8 (If RTU communication is selected, the data

b0 Data length
length selected should be 8 bytes.)

00: None _4
b2, b1 Parity bit 01: Odd

11: Even

b3 Stop bit 0: 1 bit; 1: 2 bits

0001 (H1): 110

0010 (H2): 150

0011 (H3): 300

0100 (H4): 600

0101 (H5): 1200

0110 (H6): 2400

b7~b4 Data rate
0111 (H7): 4800

1000 (H8): 9600

1001 (H9): 19200

1010 (HA): 38400

1011 (HB): 57600

1100 (HC): 115200

4-19
 St a r t e r K i t M a n u a l

Contents

1101 (HD): 500000 (Supported by COM2/COM3)

b7~b4 Data rate 1110 (HE): 31250 (Supported by COM2/COM3)

1111 (HF): 921000 (Supported by COM2/COM3)

b8 Start-of-text character 0: None 1: D1124

First end-of-text
b9 0: None 1: D1125
character

Second end-of-text
b10 0: None 1: D1126
character

b15~b11 Undefined

_4  Example: Modifying the communication format used by COM1

1. If users want to modify the communication format used by COM1, they have to add
the program code below to the top of the program in the PLC. When the PLC runs
during the first program scan, it checks whether M1138 is On. If M1138 is On, the
setting of COM1 will be changed according to the value in D1036.

2. Change the communication format used by COM1 is changed to an ASCII format

(115200 bps, 7 data bits, Even parity bit, 1 stop bit).

4-20
 Chapter 4 Appendix

4.4.4 Setting the Communication Parameters in an HMI

 DOP-107BV

Setting communication

After users click Communication Setting on the Options menu in DOPSoft, they
can set communication parameters related to COM1.

_4

4-21
 St a r t e r K i t M a n u a l

 DOP-107EV

Setting communication

After users click Communication Setting on the Options menu in DOPSoft, they
can set communication parameters related to Ethernet.

_4

4-22
 Chapter 4 Appendix

4.5 Equivalent Circuit of an I/O Simulator Board

4.5.1 Connecting to DVP14SS211R

L AC 100V~240V
50~60Hz
N
+24V

0V

S/ S
X0
_4
X1
X2
X3
X4
SR1 SR2 SR3 SR4
X5
10K 10K 10K 10K
X6
X7 Red Yellow Green Green
C0
Y0
Y1
Y2

C1
Y3

4-23
 St a r t e r K i t M a n u a l

4.5.2 Connecting to DVP12SE11R

L AC 100V~240V
50~60Hz
N
+24V

0V

S/ S
X0

_4 X1
X2
X3
X4
SR1 SR2 SR3 SR4
X5
10K 10K 10K 10K
X6
X7 Red Yellow Green Green
C0
Y0
Y1
Y2
Y3

4-24
 Chapter 4 Appendix

4.6 Installing the DVP12SE11R Driver

After ISPSoft is installed on a PC, the DVP12SE11R driver will appear in the folder in
which ISPSoft is installed. After DVP12SE11R is connected to the PC, the message
“Installing device driver software” will appear, and the PLC will install the DVP12SE11R
driver automatically.

_4

After the installation of the DVP12SE11R driver is complete, the message “Delta PLC” will
appear in the Driver Software Installation window.

4-25
 St a r t e r K i t M a n u a l

MEMO

_4

4-26