Scribd
Upload
97 views6 pages

Air Cooled HX Calculator

Uploaded by

jeanromain.bitsindou
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
97 views6 pages

Air Cooled HX Calculator

Uploaded by

jeanromain.bitsindou
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 6

FOR EDUCATIONAL PURPOSE ONLY – DO NOT USE THIS METHOD FOR DETAIL DESIGN – ALWAYS CONSULT A R

Air cooled Heat Exchanger Design Calc

To modify Calculated
If you spot a mistake or wish to suggest an improvement, please contact : [email protected]

Copyright www.MyEngineeringTools.com

The content of MyEngineeringTools.com is copyrighted but no warranty nor liability is ensured. The content of this site is
checked by the user through the quality procedure of his organization or by checking another source. The user must alw
organization own risk and own cost

FOR EDUCATIONAL PURPOSE ONLY – DO NOT USE THIS METHOD FOR DETAIL DESIGN – ALWAYS CONSULT A R
ETHOD FOR DETAIL DESIGN – ALWAYS CONSULT A REPUTABLE SUPPLIER FOR DETAIL DESIGN

Air cooled Heat Exchanger Design Calculator (estimation)

Step 1 : Assume the heat exchanger geometry


Please refer to the sheet heat exchanger geometry
Choose a density for the fins and a pitch, and a number of row
Number of rows of the exchanger Nr 5
Fins density 10 fins/in
Tube spacing 2,5 in
Face velocity FV 625

Step 2 : Gather the data required for the design


Process data
Type of heat exchanger Air cooled
Air ambient temperature T1 35 c
Hot Fluid to cool Water
Hot fluid flowrate w 500000 lb/h
Hot fluid specific heat c 1 Btu
Hot fluid inlet temperature t1 150 c
Hot fluid outlet temperature t2 50 c
Heat exchanger basic data
Tube material Steel + Al fins
Tube thermal conductivity λm 25 Btu/h.ft2.F
Tube inside diameter Di 0,834 in
Tube outside diameter Do 1 in
Heat transfer coefficient on the hot fluid side hi 1000 Btu/h.ft2.F
Fouling Heat transfer coefficient on the hot fluid side
hs 1000 Btu/h.ft2.F

Step 3 Calculate the air side heat transfer coefficient


Air side heat transfer coefficient ha 200,00 Btu/h.ft2.F

Step 4 : Calculate the conduction coefficient through the tube


Heat transfer coefficient through the tube wall hw 3614 Btu/h.ft2.F
(Note that the diameters in inches are converted in ft in the formula)

Step 5 : Calculate the overall heat transfer coefficient


Overall heat transfer coefficient U 133,77 Btu/h.ft2.F

Step 6 : Estimate air outlet temperature


Please refer to the sheet air outlet temperature estimation
Considering the overall heat transfer coefficient and the hot fluid inlet temperature
Air outlet temperature estimation T2 83 c
Step 7 : Calculate the heat exchanger size
Tubes length L 40 ft
Required heat duty of the exchanger Q 90000000,00 Btu/h
Face area of the exchanger FA 1538,46 ft2
Heat exchanger width Y 38,46 ft

Step 8 : Calculate available area and check it is sufficient


Select a bundle width 120 in Must change by 6 in incremen
Required number of bundles 3,85
Selected number of bundles Nb 4 Round the value calculated ab
Designed Heat exchanger width Y 40,00 ft
Number of tubes per row Nt 191,00
Calculated air outlet temperature T2 81,15 c
Calculated DTML DTML 35,34 c
Required heat exchange area A required 10577,99 ft2
Available exchange area A available 10000,74 ft2
Available > Required ? Design not ok, change bundle width
if yes, the design is acceptable, if not come back to the bundle width and adjust

Step 9 : calculate the air side pressure drop and fan power requirement
Air pressure drop Dpa 0,50 inches W
Required fan power bhp 185,05 bhp

ent, please contact : [email protected]

ut no warranty nor liability is ensured. The content of this site is to be seen as a help and important information and calculation must always be doub
s organization or by checking another source. The user must always respect all applicable regulation. The use of the information is at the user and its
organization own risk and own cost.

ETHOD FOR DETAIL DESIGN – ALWAYS CONSULT A REPUTABLE SUPPLIER FOR DETAIL DESIGN
Must change by 6 in increments, minimum 48 in, maximum 144 in

Round the value calculated above

d calculation must always be double


e information is at the user and its

You might also like