Smart Energy Management

Traditional energy management systems are either based on electricity

billing information, an expensive and complicated sub metering system, or
portable devices that take a sample of energy usage.

The KIGG Smart Energy Management System (SEM) using the latest
Smart Technology offers low cost continuous on line monitoring, flexibility
of monitoring points and sensor types, ease of use and installation.
Through the use of a self healing wireless mesh network (Zigbee) Sensors
and Control Boxes can be added to the network in a plug and play
arrangement. Apart from the wiring to the Sensor Box the network is
wireless. Through the use of a SEM System the data can be stored and
monitored on line, graphs of time vs usage created for analysis purposes.
Control boxes allow a remote control of systems such as lighting, heaters,
air conditioners, pumps etc. Should you find that after evaluation of the
initial findings that some of the monitoring points are not ideally positioned
then they can be easily moved to another location. Once the first stage is
completed and energy data is being collected, you may wish to also add
other sensors and control boxes and expand the system to monitor /
control for example temperature, Co2, Ph of pools etc. all of which is
practically achievable with the KIGG SEM System. What is more it is quite
practical to start with a limited system and expand the system both in
energy monitoring and other monitoring. A very wide range of compatible
sensors exist beyond that of electricity monitoring.
Evaluation of energy data is not restricted to a control
room nor does the operator need to dedicate his full time
to this task. Data can be monitored from anywhere via
browser on a secure smart tablet/phone/Laptop/PC.
Anywhere an internet connection exists. Thresholds can
be set to warn the operator should a threshold (e.g.
amount of current used) be exceeded/triggered, even to
the extent of sending an SMS or email etc.

Electricity saving occur through the intelligent switching

and reduction of electricity usage. Switching off
equipment is not enough. To carry out real savings in
electricity costs it is necessary not only to monitor the
data from the utilities electricity meter as usually occurs
when using billing information, but to get inside the
electrical system and monitor and control sub sections of
the electrical system throughout the facility, what is more
the determination of the timing of usage is important. By
analysing subsections and timing as well as using control
functions. Maximum Demand costs can be avoided by
avoiding/controlling peaks as well as general savings.
The principle of “Just in Time” is the ideal approach to
electricity savings. A system should be fully working just
in time for its use and reduced or put to standby
afterwards.

Version 1.6 Page 1 *Content subject to change without prior notice

 Smart Energy Management

The SEM System uses Wireless Zigbee communication connects to the ZigBee Sensors and Control Smart
Device. This makes the SEM System compatible capable with any Zigbee Single and Three Phase Electricity
Smart Meters, Smart Flow and Gas meters. To put it precisely the SEM System is compatible with any ZigBee
enabled device as long as our engineers have access to the communications and protocol commands of the
device. This allows you to build a unique custom metering, monitoring and control solutions, by mixing Zigbee
enabled Smart Meters, Energy Sensors, Flow sensors, Pressure Sensors or any of the 200+ Sensors and
Control Devices in the KIGG Catalogue. Not only is the SEM system is extremely versatile, but is a very easy,
plug and play universal solution in reducing Your Costs, Saving You Time, Saving You Energy, Aid in Safe
Guarding the Health and Well-Being of Animals and People, Security, Theft Detection and Protection of
Critical Assets, Increasing Efficiency, and Monitoring the Environment. KIGG has Hundreds of Sensors and
Control Smart Device, including a section of ZigBee enables Smart Meters. Simply Choose the appropriate
Smart Device or Smart Meter that meet your Energy Monitoring Requirements, whether it be monitoring of
Voltage, Current, Active energy & power, Reactive energy & power, Apparent Energy & power, Power Factor
and Frequency. Please see catalogue for more Smart Devices.
Using the SEM System you can monitor energy and manually control equipment wirelesses from anywhere or
you can automate the process by setting thresholds and triggers. Triggers can control other Smart Devices,
Send messages, Alerts via Email, SMS and visually/audible alarms with the right Smart Devices. Voltage and
current are fundamental factors when looking at measuring energy consumption of equipment inside a
Building or outside at Site. These are the basic tools required to start lowering power consumption and saving
you money. The SEM System is a very easy, versatile, plug and play, wireless, industrial and reliable self
healing system.
The SEM System is Plug and Play so no technical knowledge or engineering is required and included is a
user manual with all required information. Upgrading or adding Smart Device is easy; simply purchase, place
and switch on.

Smart Energy Meter (Sub metering)  Current Smart Sensors Fixed (Intrusive).
Single Phase Smart Meter (Zigbee) Class 1 Input current: 0A - 10A Measurement resolution: 10mA, Max.
Three Phase Smart Meter (Zigbee) Class 1, 0.5 Error: 0.5% Other Current ranges available: 25A, 50A, 100A
More SEM Smart Sensor and Control Devices  Single Phase & 3 Phase Multi-parameter Smart Energy
 Appliance & Equipment control Switch Smart Box: transducer:
Latching relay Max. Voltage: 250V Current ranges Input measurement range: Frequency: 45 to 65 Hz (AC),
options: 3A (720W), 5A (1200W), 100A (24,000W / Voltage: 0 to 500V AC (must specify required voltage),
2.4kW) (UK Socket, others on request) Current: 0 to 50A (must specify required current), Measures
Voltage, Current, Frequency, Active Power, Reactive Power,
 Single Phase voltage Smart sensor
Power Factor, Active Energy and Reactive Energy. Accuracy:
Input range: 1V to 1000V AC Accuracy: 0.2% or 0.5%
0.5% Frequency measurement accuracy: 0.05Hz, Refresh
depending on requirements (Direct Connect)
Rate: 100mS
 3 Phase voltage Smart sensor
Input Range: 50V to 500V AC Accuracy: 0.2% or 0.5%  Sample rate: Variable based on Logger: Tablet : Min 1
depending on requirements (Direct Connect) Second & SEM Logger Min 1Second
 Sampling methods: See Smart Sensor or Control Smart
 Current Smart Sensors Device Specs
Input current: 0A - 10A Measurement resolution:  Data Storage: On SEM Logger device and online via Cloud
10mA, Max. Error: 0.5% Other Current ranges  Software: Optional data analysis software is available.
available: 25A, 50A, 100A (Intrusive).
 Power Supply: 230V+ 10%, 50Hz as standard (others on
 Current Smart Sensors Fixed (split-core CT). request)
Input Current: 0A - 600A (must specify required max  Housing: Relevant IP rated housing, Options include: Vented
value), Accuracy/ Max Error: 1%, Window size: 1.25” Indoor, Outdoor Water Proof, DIN Rail, More on request
(Non-Intrusive)  Operating Temp: -10 to +60°C & Max storage Temp: 70°C
 Relative Humidity: 10 to 80%
Version 1.6 Page 2 *Content subject to change without prior notice
 Smart Energy Management

Smart Tablet
A Tablet is not only a display and control tool used in addition to a
Smart Logger; it can also be a very cost effective and easy to use
alternative to the Smart Logger. Tablets are common and it is the
next logical step to use it as a Logger for the SEM Wireless Smart
Sensors. Tablets are extremely reliable and have all the
communications needed to collect data and relay it onto the internet
through Wi-Fi or built in Mobile SIM (4G/3G/GPRS/GSM).
Additionally the screen, ease and familiarity of the software and
interface, its own battery supply if mains power fails, makes it an
ideal Logger and child’s play for anybody to build their own
monitoring system. This is aimed at people who want rapid
deployment of a mobile or fixed monitoring solution. Imagine having
your Tablet next to you showing instantaneous sensor reading of
multiple Smart Sensors outside, across fields, or scattered inside
buildings, across a plant or in workshops. Imagine being able to
setup up a mobile or fixed monitoring solution extremely quickly
through plug and play, and having access to historical data, backed
up to an online server for later analysis. All of this is quick and
easy and using the tablet as a logger will save you time and money.

Smart Tablet
Ideal for Site
monitoring, portable
monitoring, and Small
Scale Systems

Version 1.6 Page 3 *Content subject to change without prior notice

 Smart Energy Management

SEM System Smart Logger

The Smart Logger is ideal solution for fixed or unsecure environments where a tablet could be stolen. The
Smart logger provides nearly all the functionality that the tablet does without the Touch Screen interface. The
Smart Logger comes with a built in Co-ordinator, unlike the tablet you do not require to purchase a separate
Co-ordinator. In addition to the Wi-Fi and Mobile SIM (3G/GPRS/GSM) the Smart Logger has an Ethernet
Port (LAN) for direct connection. Again setup and installation is plug_and_play, just simply power on the
Smart Box Sensors and they Auto connect with the Smart Logger. When using Wi-Fi and Ethernet (LAN) with
secure networks we have provided an LCD display for you network administrator to configure the Smart
Logger.

The Smart logger uses an industrial housing and is mountable using bracket DIN rail Standard. We provide a
DIN rail for users to easily mount it on a Wall. Simply fix the Small DIN rail to a Wall using Screws and Clip
the Smart Logger onto it. Removing is simple just pull the latch to unclip. The Smart Logger is suitable for
Industrial, Commercial, Home and Scientific environments.

Smart Logger
Ideal for Fixed
Monitoring for SME’s,
Industrial and
Small/Medium Scale
Systems

Version 1.6 Page 4 *Content subject to change without prior notice