Technical Data Sheet

SNAPSIL™ TSE322 SILICONE ADHESIVE SEALANT

Description
SNAPSIL TSE322 silicone adhesives are one-component heat curable silicone adhesive sealants which will
bond to many substrates without a primer and which will cure rapidly at elevated temperatures. These products
have a very long working time at room temperature but will not cure completely until exposed to elevated
temperatures.

TSE322 - is a light blue, flowable material with self-leveling properties.

TSE322-B - is a black, flowable material with self-leveling properties

Key Features and Typical Benefits

One component products - no mixing required
Fast cure at elevated temperature
Primerless adhesion to many substrates
Non-corrosive to metals and sensitive substrates
Excellent dielectric properties
Outstanding performance over a wide thermal range

Typical Physical Properties (JIS

K6249)
Property Unit Value
Uncured Properties TSE322 TSE322-B
Color Lt Blue Black
Viscosity Pa·s 110 110
Specific Gravity 1.27 1.27
Cured Properties (cured 1 hour at 150 ºC)
Hardness (Type A) 45 45
Elongation % 230 230
Tensile Strength MPa 3.4 3.4
Adhesion (al to al) MPa 2.5 2.5
Dielectric Strength kV/mm 20 20
Dielectric constant (60Hz) 3.1 3.1
Dissipation Factor (60Hz) 0.006 0.006
Volume Resistivity Ω·cm 1.0 x 10 15
1.0 x 1015
Typical physical properties are average data and should not be used as or to develop product specification.

HCD-TSE322 (Rev. 2021-05-05 1:47 PM) Page 1 of 6

TSE322

Note: Test results. Actual results may vary.

Note: Test results. Actual results may vary.

Processing Recommendations
Compatibility
SNAPSIL TSE322 silicone adhesives will cure in contact with most clean, dry surfaces. However, certain
materials, such as butyl and chlorinated rubber, sulfur-containing materials, amines, and certain metal soap cured
RTV silicone rubber compounds can cause cure inhibition. Cure inhibition is characterized by a gummy
appearance of the TSE322 silicone adhesives at the interface between the adhesive and the substrate to be
bonded. It is recommended that a sample patch test be performed with the TSE322 silicone adhesives to
determine substrate compatibility.

Surface Preparation
The adhesive performance of any polymer system is highly dependent upon proper surface preparation. In order
to maximize the adhesion TSE322 silicone adhesives and minimize the potential for cure inhibition, all parts
should be as clean and dry as possible prior to the application of the adhesive.

HCD-TSE322 (Rev. 2021-05-05 1:47 PM) Page 2 of 6

TSE322

Bonding
SNAPSIL TSE322 silicone adhesives offer outstanding adhesion characteristics to a wide variety of different
substrates without the need of a primer.

Note: Test data. Actual results may vary.

For difficult-to-bond-to substrates, or where more aggressive chemical adhesion is desired, the adhesion may be
enhanced by using SS4155 silicone primer, available from Momentive Performance Materials. To apply the
primer, thoroughly clean the surface and let dry. Then apply a uniform film (0.01-0.02 mm / 0.5-1.0 mil) of
SS4155 silicone primer and allow the primer to air-dry for one hour or more. For more details on priming and
adhesion, please refer to Momentive Performance Materials product data sheet on silicone primers.

HCD-TSE322 (Rev. 2021-05-05 1:47 PM) Page 3 of 6

TSE322

Curing
SNAPSIL TSE322 silicone adhesives requires the use of elevated temperatures in order to achieve full cure.
Typical cure times and temperatures are as follows:

Note: Test results. Actual results may vary.

The actual cure time is affected by such things as cross-sectional thickness of SNAPSIL TSE322 silicone
adhesives, heat capacity of the overall assembly and efficiency and type of oven used (i.e. convection, infrared)

Note: Test results. Actual results may vary.

General Considerations for Use

While the typical operating temperature for silicone materials ranges from -45℃ to 200℃, the long-term
maintenance of its initial properties is dependent upon design related stress considerations, substrate materials,
frequency of thermal cycles, and other factors.

Patent Status
Nothing contained herein shall be construed to imply the nonexistence of any relevant patents or to constitute the

HCD-TSE322 (Rev. 2021-05-05 1:47 PM) Page 4 of 6

TSE322

permission, inducement or recommendation to practice any invention covered by any patent, without authority
from the owner of the patent.

Product Safety, Handling and Storage

Customers should review the latest Safety Data Sheet (SDS) and label for product safety information, safe
handling instructions, personal protective equipment if necessary, emergency service contact information, and
any special storage conditions required for safety. Momentive Performance Materials (MPM) maintains an
around-the-clock emergency service for its products. SDS are available at www.momentive.com or, upon request,
from any MPM representative. For product storage and handling procedures to maintain the product quality within
our stated specifications, please review Certificates of Analysis, which are available in the Order Center. Use of
other materials in conjunction with MPM products (for example, primers) may require additional precautions.
Please review and follow the safety information provided by the manufacturer of such other materials.

Limitations
Customers must evaluate Momentive Performance Materials products and make their own determination as to
fitness of use in their particular applications.

Contact Information
Email
[email protected]

Telephone
Americas Latin America EMEAI- Europe, Middle ASIA PACIFIC
East, Africa & India
+1 800 295 2392 Brazil Europe China
Toll free* +55 11 4534 9650 +390510924300 800 820 0202
+704 805 6946 Direct Number Direct number Toll free
Direct Number +86 21 3860 4892
Direct number
*All American countries Mexico India, Middle East & Africa Japan
+52 55 2169 7670 + 91 44 71212207 +81 3 5544 3111
Direct Number Direct number* Direct number
*All Middle Eastern countries, Korea
Africa, India, +82 2 6201 4600

For literature and technical assistance, visit our website at: www.momentive.com

DISCLAIMER:

THE MATERIALS, PRODUCTS AND SERVICES OF MOMENTIVE PERFORMANCE MATERIALS INC. AND
ITS SUBSIDIARIES AND AFFILIATES (COLLECTIVELY “SUPPLIER”), ARE SOLD SUBJECT TO
SUPPLIER’S STANDARD CONDITIONS OF SALE, WHICH ARE INCLUDED IN THE APPLICABLE
DISTRIBUTOR OR OTHER SALES AGREEMENT, PRINTED ON THE BACK OF ORDER
ACKNOWLEDGMENTS AND INVOICES, AND AVAILABLE UPON REQUEST. ALTHOUGH ANY
INFORMATION, RECOMMENDATIONS, OR ADVICE CONTAINED HEREIN IS GIVEN IN GOOD FAITH,

HCD-TSE322 (Rev. 2021-05-05 1:47 PM) Page 5 of 6

TSE322

SUPPLIER MAKES NO WARRANTY OR GUARANTEE, EXPRESS OR IMPLIED, (i) THAT THE RESULTS
DESCRIBED HEREIN WILL BE OBTAINED UNDER END-USE CONDITIONS, OR (ii) AS TO THE
EFFECTIVENESS OR SAFETY OF ANY DESIGN INCORPORATING ITS PRODUCTS, MATERIALS,
SERVICES, RECOMMENDATIONS OR ADVICE. EXCEPT AS PROVIDED IN SUPPLIER’S STANDARD
CONDITIONS OF SALE, SUPPLIER AND ITS REPRESENTATIVES SHALL IN NO EVENT BE RESPONSIBLE
FOR ANY LOSS RESULTING FROM ANY USE OF ITS MATERIALS, PRODUCTS OR SERVICES
DESCRIBED HEREIN. Each user bears full responsibility for making its own determination as to the suitability of
Supplier’s materials, services, recommendations, or advice for its own particular use. Each user must identify and
perform all tests and analyses necessary to assure that its finished parts incorporating Supplier’s products,
materials, or services will be safe and suitable for use under end-use conditions. Nothing in this or any other
document, nor any oral recommendation or advice, shall be deemed to alter, vary, supersede, or waive any
provision of Supplier’s standard Conditions of Sale or this Disclaimer, unless any such modification is specifically
agreed to in a writing signed by Supplier. No statement contained herein concerning a possible or suggested use
of any material, product, service or design is intended, or should be construed, to grant any license under any
patent or other intellectual property right of Supplier covering such use or design, or as a recommendation for the
use of such material, product, service or design in the infringement of any patent or other intellectual property
right.

The use of the “™” symbol designates registered or unregistered trademarks of Momentive Performance Materials Inc. or its affiliated companies. Momentive and the
Momentive logo are trademarks of Momentive Performance Materials Inc.

HCD-TSE322 (Rev. 2021-05-05 1:47 PM) Page 6 of 6