2 lN l Anti-Static

Electric Suction Tin Soldering Station

w
948

fa
!7
Thank you for choosing this lntelligent suction tin soldering station, this product is specially
designed for lead-free soldering station, please read the instructions carefully before use,
after reading please keep for future reference
 l. Featu res
1. Uses PID programmable temperature control technology, applying
sophisticated PID programming into the machine to rapidly track, test, and
correct the actual temperatures of the suction tin soldering station and high
frequency soldering station. Rapid temperature compensation reduces
temperatu re error. Tem peratu re stabi ity and tem peratu re com pensation
I

speed are significantly better than similar products.

2. With suction tin gun and soldering iron two functions, this two function can
intelligent Recognition. When you need suction tin soldering station, take
soldering iron, and connect suction tin gun, the machine can intelligent
recognition. When you need soldering iron, take out suction tin soldering
station, and connect soldering iron, the machine can intelligent Recognition.
3. Anti-static design, prevent static electricity or leakage damage components.
4. .Built-in vacuum, strong suction, no external vacuum system, easy to carry.
5. Adopt isolated transformer power supply to heating, power supply voltage is
low voltage, safe and reliable
6. Stand with the integration design, installed on the side of the machine, more
stable, don't worry the stand shift that affect the operation.
7 . The machine is designed with the following powerful features of human
nature:
A. Sleep function:
Machine with self-detection functionality automatically, when it is unattended
and not in use, pauses fora set duration prior to sleep mode, and
automatically cools to200'C. lt will then enter sleep mode to prevent
soldering iron oxidation and effectively extend soldering iron head service
life while retaining energy savings and environmental protection. The sleep
time ranges from: 1-99 minutes, in1 minute intervals. Users can set the time
according to personal usage patterns. lf the sleep function is not necessary
for the soldering iron, the sleep time should be set to:
Wake-sleep methods:
a. Shake soldering iron handle/push red button
b. Press any key.
c. Turn off the power switch on again.
B. Auto-off function:
After the machine into hibernation, the program start time, in the set auto-off
time not wake dormant, the machine will automatically shut down, saving and
environmental protection. Automatic shutdown time setting range: 1-30
minutes, in steps of 1 minute.
G. Temperatu re calibration
Because of the environmental impact or replacement heater and the
soldering iron tip parts that cause deviation between solder iron temperature
and display temperature , you can use this function for calibration.
D. Gelsius/ Fahrenheit temperature display function:
To meet the market needs of different regions and design temperature
display mode, you can select according to customary interest.
8. The tin suction mouth and heating pipe use special design, so the solder can
be inhaled filter in the molten state, which don't need to maintain frequently,
and high work efficiency.
9. Using silicone heat-resistant hose to prevent from contacting heating
element which will cause damage.
10. The lnternal use SMT double-sided board manufacturing process. The
process is neat, and the flow signal is clear. The stability and safety
performance of the machine are further improved, which make the machine
can adapt to all kinds of bad environment.

ll. Specificatlons
Suction tin soldering station power <90w
Soldering iron power 60w
Suction tin gun temperature range 350"C-490" C I 662"F-896"F
Soldering iron temperature range 200"c-480' c I 392'F-896"F
Display method LED
Temperature stability + 1"C (static)
Heating element voltage AC 26V t10o6
Desoldering pump power 12W
Vacuum suction 0.05MPa
Tip of ground impedance <2ohm
Dimensions L234 xW202 x H 134mm *5mm
Weight 4.4k9
Length of cable 7120cm
Operating temperature 0'c-40'c 132"F-104'F
Storage temperature -20'c-80" cl -4" F - 17 6" F
Storage humidity 35oh-45o/o
lll. Paneln Suction Tin Soldering lron Handle Diagram

1. Model
2. Suction tin soldering station/
soldering iron temperature display
3. Suction tin soldering station/
soldering iron minus key
4. Suction pen interface/suction
tin soldering station trachea interface
5. Handle connector(8 core)
6. The function keys
7. The power switch
8. Suction tin soldering station/
soldering iron plus key

5
1. The suction nozzle
6
2. Steel
7
3. Nuts
4. Filter
5. After the grip assembly
6. Release Button
7. lndicator
8. Protect cabin
9. Trachea
10. Suction tin soldering station
handle line schematic diagram
11 . Suction tin soldering station
switch
 lV. Operati ng lnstructions
L Connect suction tin soldering station handle or soldering station handle.
2. Connected to the power supply.
3. Turn on the power switch, soldering station begin heating.
4. Press plus or minus key to set the temperature you need, soldering station
can work when temperature be stable, suction tin soldering station can work
after power on 3 minutes; use suction tin nozzle trap on the foot of element,
and melt the solder tin completely, then push the red button on the suction tin
soldering station, cleaning the tin.
5. After work, put the soldering station handle or suction iron handle back to
iron holder, turn off the power.

Precautions!
1. Suction tin soldering station handle and soldering handle share one
interface. When use suction tin soldering station, this handle connect on 8
core interface, trachea connect on. When use soldering station, take out the
suction tin soldering station handle and connect soldering iron handle.
2. Notes to use suction tin soldering station:
A. Solder tin must be melted completely ,then push red button.
B. lf there is a printed circuit board solder residue within the aperture, we
need to re-welding, and then repeat the desoldering process.
G. lf the element foot rely on the PCB aperture side, unable clean solder,
firstly need re-welding,Then use Nozzle melt the solder, and then slowly
move to the suction nozzle, moving foot drive element, make the element is
not in contact with the foot aperture, then buckle suction soldering station red
switch, the solder sucked clean.
D. Suction nozzle holes are not clogged, buckle suction soldering red switch
to observe the indicator color. lf it is red, or more than half, need to clean up
the suction nozzle, heating element, filter tubes. lf it is blue or little red, no
need clean
E. Nozzle with different dimensions, they are:O0.8MM, O1.0MM, O1.2MM,
O1.6MM, O1.8MM, 02.0MM, bigger nozzles suitable for big welding plate of
large components foot, small nozzle suitable for small welding plate of small
components foot.
 V. Function Setting Description

Function set order, press the * key switch:

Fahrenheit/ Celsius
FC"pl) Automatic Shutdown ) Temperature

A. Sleep Time Set

1 . Turn on the power switch, press once * keY, the display shows "L01" "01"
flashing as picture, as this time for the 1 minute sleep time.
2. Press the plus or minus key to set the desired sleep time, tap to one
minute changes, long press for quick setting.
3. lf you need to set other functions, press the :t button
to select other functions set up after. No need to set
other functions, stop operating for 6 seconds,
program automatic save and exit function setting
interface and sleep time setting complete.

B. Auto-OFF Setting
1 . Turn on the power switch, press two the * key, the display shows 'P01"
"01" flashing, flashing as picture, this time for one minute off time.
2. Press the plus or minus Key to set off the time required, tap to one
minute changes, long press for quick setting.
*
3. lf you need to set other functions, press the button to
select other functions set up after. No need to set
other functions, stop operating for 6 seconds,
program automatic save and exit function
setting interface, auto-off setting completed.

C. Fahrenheit / Gelsius Temperature Display Mode Settings

1. Turn on the power switch, press three times the * key, the display shows
"C", "C"as picture, as this time is Celsius temperature display mode
setting.
2. Press plus or minus keys to set the display mode you
need.
3. Press the * key after setting up, program automatic
save and exit function setting interface, setting
completed.
D. Digital temperature correction settings
This function can be used to correct the temperature deviation caused by
environmental changes or replacement of heating elements soldering iron
tip and other accessories; temperature correction can effectively improve
the operating efficiency and extend the service life of the soldering iron.

1. Turn on the power switch, and press the plus and minus keys simultane-
ously for 2 seconds after the temperature stabilizes. The display shows 4
decimal points in addition to the set temperature.
2. Press the plus and minus keys to enter the measured temperature.
3. Simultaneously press the plus and minus keys for 2 seconds to confirm,
the program automatically corrects and saves the temperature, and exits
the setting interface, the temperature calibration is completed. lf the temp-
erature still has a slight deviation, the calibration can be repeated.

minus key plus key

Vl. The Tip Maintenance and Description

Overheating will weaken tip function, it should select the

Tip Temperature
lowest possible temperature. This tip temperature
recovery superior force, low temperature rechargeable
soldering, to protect temperature sensitive components.

Should regularly clean sponge to clean the tip after welding

residual flux tip derived carbon compounds and oxides can
damage the tip, causing welding error, or to tip thermal
Clear Up
dysfunction. When long continuous use soldering iron,
the tip should be open once a week to clear oxides,
prevent damage and reduce the temperature of the tip.

When not using a soldering iron, do not let a long time at

When Not in Use high temperature soldering iron, solder will head into iron
oxide, causing the tip thermal function greatly diminished.

After use, you should wipe the tip, tin-plated on a new layer
After Use to prevent tip oxidation
1. When iron initial use, pay attention to check the temperature of iron Tip
situation, wait until the temperature is just to melt tin wire, iron Tip in part
coated with tin, then the temperature was raised to the desired temperature.
Remember that when you work with a layer of iron Tip tin should be long-term
protection of iron Tip, in order to achieve optimal welding functions.
2, Such as the surface layer of iron oxide, causing the tip temperature of illusion,
can not melt tin and tin, and iron core at this fever are at high temperature.
When this happens, do not blindly raise the temperature again. Application of
clean Sponge remove oxides, if not clear, please power off until the iron
temperature was lowered to room temperature, with sandpaper carefully
remove the oxide, and then repeated the first point of the first use of iron
3. Note that after the iron is hot work, welding metal frame back into the stand,
should the temperature knob to stand below 250'C. Standby time more than
20 minutes, turn off the power. Otherwise, long iron at a high temperature on
standby, due to the generation accumulated between iron frame and iron, so
that heater accelerated aging, soldering iron Tsui oxide derivative, direct
reduced welding function, leading to severe the connection nut plastic melt or
heater circuit.
4. Do not use the rasp removing oxide tip, if the tip deformation or derivative
rust, must be replaced with new tiP.
5. Do not give the welding tip too much pressure, so as not to alter the thermal
performance, but will make the tip damaged

Vll. Maintenance and RePlacement

1. Suction tin station nozzle cleaning/ maintenance is the same with soldering
station tips.
2. Suction nozzle, heating element, filter tube cleaning.
A. Suction Nozzle Gleaning
lnsert the plug into a power outlet, turn on the power switch, -I>----a
??

so that the suction nozzle heat seiect the appropriate suction

nozzle cleaning needles to clean the suctionnozzle bore.

B. Heating Element Cleaned

Heatingllement screwed out of the nut after cooling, remove the pipe and the
suction nozzleturn on the power switch, so the heating elements heat. Clean
with a suitable needle to clean the heating element inside the hole turn off the
power to clean up after.
 Note:
Heating element inside the hole solder must melt before they can be cleaned. lf
you can not clean the needle through the heating element bore, replace the
heating element. When assembled, the nut must be tightened, low temperature
or suction nozzle.

Heating element Nozzle pipe Nuts

Body heat Heating element
I

[I-- il- _..

A
-llF -lF+

C. Filter tube cleaning

1) Turn off the power, and so the filter after cooling remove the filter.

C. Replace the filter tube.

B. Automatic pop-up

i A. Pulldown

2) Press the diagram of the filter to break up and remove the spring filter tubes,
filter tubes spring clean up solder.
Note: The filter tube is very hot, be careful not to burn.

ffiffi
Front cover SPring filter tube Ceramic fiber filters

When the filter assembly components need to be replaced with the following
phenomena:
* Spring filter tube can not be removed or soldering solder reservoir two-thirds
needed to replace the spring filter tubes.
*
The front cover stiff and cracked, you need to replace the front cover.
* Ceramic fiber filters too much solder and flux due to siltation and stiff, the need to
replace the ceramic fiber filters.

3. The replacement of the heating element

O Unplug the power cord and the heating element to cool.
@ Panasonic nuts, remove the pipe and the suction nozzle.
@ Panasonic fixing screws of the heat generating element.
@ Remove the filter,
@ Cabin, open cabin protection.
@ Unptug the heater element connections, remove the heating element.
O Retoad new heating element.
@ UetnoO according to the original wiring connected to wires.
@ ln reverse order of assembly suction tin soldering station, and re-calibrate
the temperature

Panasonic nuts, remove the

pipe and the suctio n nozzle

Heating element Nozzle Body heat PiPe Nuts

@: t"T> [---l
L

Panasonic fixing screws of the heat

@/ generating element

Remove the filter

Guard cabin

Loosing cabin retaining screws,

open cabin guard

Heating element

Unplug the heating element connection,

remove the heating element
Vlll. Suction Gun Parts List

20

1. The front cover

2. The filter spring
3. The filter tube
4. Ceramic fiber filters
5. Ring
6. After the grip assembly
7. Release Button
8. The release button spring
9. Nursing bilge cover
10. Trachea
11. S-type clamp
12. Suction gun handle line
13. Line cards
14. Retaining compartment cover
15. A switch
16. Board
17. The heat generating element
18. Suction nozzle
19. Steel
20. The nut

11
 ) liiiiiiiiiiiiii

rur
B-u

1. Front panel
2. PCB board
3. Machine case
4. Transformer
5. Bottom case
6. Powersocket
7. Vacuum pump

12
 Model NO.

Product lD
Upon examination products meet technical ao?r
Examine standards qY
Sales Date

Date of manufacture

Thank you for choosing this type of products, please read the following terms
before using:
1. From purchasing date within 7 days, under normal use(Non-artificial damage),
new package, not be disassemble and repaired ,enjoy replacement service.
2. From purchasing date within one year, under normal use, if there are quality
problem, not be disassemble and repaired ,enjoy free repair service.
3. For more than warranty, we provide a lifetime warranty service, free of labor
costs, charge only spare parts costs.
4. Failure to present warranty card during warranty period, the company will not be
a free service.
5. Users need warranty service, please contact your original sales unit.
6. When users need warranty service, please provide warranty card and purchase
invoice, or receipt of the certificate of the company seal.
7. Warranty does not include transportation costs and provide on-site service.

NO. Date for repair Cause Fix date Repairer

Statement: The cornpany reserves the right to improve and upgrade products, product
specifications and dOsign are subject to change without notice.
When using this machine, the following basic measures should be strictly
followed to avoid electric shock or bodily injury, avoid firehazards such
phenomena.
1. ln order to ensure personal safety, unplug the power cord! The
machine after work is completed.
2. Serious consequences may result if non-original or non-approved parts are
used.
3. ln the event of product failure, repairs must be carried out by professionals
or manufacturer-designated personnel.
4. This product uses three-wire grounded plug must be inserted into three-
hole grounded outlet, do not change the plug or use an ungrounded three-
headed adapter leaving poor grounding.
5. After the desoldering station is switched on, its temperature can exceed
400'C. Do not use near flammable or explosive objects. To avoid burns, do
not touch the metal part of the soldering iron.
6. Make sure the machine before the machine is turned on in a safe state,
do not leave their jobs after opening.
7. When installing or removing components, turn off the machine track, and
after cooling heat pipe and metal parts before installation.
8. After used, remember that the cooling body before installation.
9. The desoldering station should only be used for soldering. Do not hit the
desoldering gun station against the work surface to remove flux residues,
as doing so may seriously damage the soldering iron.
10. May take the smoke for the first time, please do proper ventilation.

1. lf the power cord is damaged, in order to avoid danger, need replace parts
from the original manufacturer or professional maintenance personnel
change.
2. Lay down on the bracket when not use
3. Be careful when using the machine near the flammable materials do not
use the appliance for along time in the same place.
4. Be aware that heat may transfer to distant flammable materials; When you
need someone to look after the appliance is turned on.
5. The apptiance is not intended for use by the presence of physical,
sensory or mental defector lack of ability to use the experience and
knowledge of people(including children), unless a person responsible for
their safety against them related to the use of the appliance supervision
or instruction; Children should be supervised to ensure that they do not
play with the appliance.