Scribd
Upload
19 views6 pages

Gedm Tower Partlist

Uploaded by

catur skak
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as TXT, PDF, TXT or read online on Scribd
19 views6 pages

Gedm Tower Partlist

Uploaded by

catur skak
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as TXT, PDF, TXT or read online on Scribd
You are on page 1/ 6

#####################################################

#
#
# This list may not be complete and with all the changes done so far
# it is possible that some of the small parts are not needed anymore
#
#
#####################################################

#####################################################
####
#### Parts for the shielded spark generator
####
#####################################################

Shielded enclosure:

1x 19" 3U rack mount case 300mm deep ( plenty of room for everything )

( You can use a big scooby doo metal lunchbox to archive the needed RF/EMI
shielding too. Whatever floats your boat )

Main PSU:

1x 65V 12.3A 800W LED Switch Power Supply Driver AC 110/220V to DC 65V
Transformer for LED Strip CCTV Security System,Camera,3D Printer,Computer
Project,Motor

Motor PSU ( powers the steppers, the pump, the spindle motor and the mosfet gate
driver ):

1x AC 110V/220V to DC 12V 10A 120W Universal Regulated Switching Power Supply


Adapter Transformer Driver Converter for LED Strip Light, CCTV Security Camera
System, Computer Project

Step down converter to control voltage and current:

/**
*
* If money is no issue I recommend the bigger one.
* I use the small one that can deliver a maximum of 5A which I'm happy with
*
**/

Programmable DC Numerical Control Power Supply


1x DPM8605; 0 - 60v; 0 - 5A; 300W

or

/** that is a lot of power and it is easy to burn the mosfets with this **/
1x DPM8624 0 - 60 V 0 mA - 24 A 1400 W
Ventilation:

1x 12v 120mm Fan

Connectors:

1x 4mm banana plug sockets; 1x red and 1x black;


1x 4mm banana plugs; 1x red and 1x black;
1x GX16 aviation socket; 4 pin;
2x GX16 aviation plug; 4 pin;

Some WAGO terminals

Some M3, M4, M5, M6, M8 screws, nuts and T-slot nuts and a set of setscrews.

#####################################################
####
#### Other Parts
####
#####################################################

1x 12v Peristaltic Pump 3mm x 5mm silicone tubing. 150ml/min


1x 3mm x 5mm silicone tube; 2 meters;
The diameter of the silicone tube is important if it is used with the round bar
drill jig. 150ml/min seems to work "ok".

1x Touch display 320x240 ILI9341 2.4"

There are different models available. It is important to choose the correct


one. Some have larger PCBs.
This display is available without tuch too. Touch is needed!

HiLetgo 2.4" SPI TFT LCD Display 2.4 Inch ILI9341 Touch Panel LCD ILI9341
240x320 5V 3.3V

6x DC Power Sockets and plugs

5.5 x 2.1 mm DC Power Jack Socket Threaded Female Panel Mount Connector Adapter
with Dustproof Plug 6Pack

1x On/Off rocker switch. 2poles. For 13mm*19mm pocket. ( A 5 Pack is good to have )

On/Off Boat Rocker Switch 5Pcs 2 Pin Position Snap 12V 110V 250V QTEATAK
3x Micro limit switch ( A pack of 25 is good to have. They are cheap )

Cylewet 25Pcs AC 1A 125V 3Pin SPDT Limit Micro Switch Long Hinge Lever for
Arduino (Pack of 25)

7x Aviation Connector Plugs and sockets GX16 4PINs ( They are available with
2,3,4,5 Pins. We need the 4 Pin version )

Aviation Connector Plugs, Lsgoodcare 30Pcs 16MM 4 Pin Din Female/Male Aviation
Wire Connector Plug, AC 200V 5A GX16-4 Pin Metal Chassis Thread Panel Connector
Socket

2x Banana sockets and plugs. One red and one black ones for 8mm hole.

10Pcs Black and Red 4mm Banana Jack Socket Female Adapter Panel Mount Binding
Post for 4mm Banana Plug Connectors

2x 4mm Banana plugs. One red and one black.

A big set jumper wires. 10cm and 20cm. Male to male and male to female for both
sizes.

4x Standoff Male/Female 10mm


4x Standoff Male/Female 20mm
4x Standoff Male/Female 30mm
4x M3 Nut
4x M3x6 Screw

Csdtylh 320Pcs M3 Motherboard Standoffs&Screws&Nuts Kit, Hex Male-Female Brass


Spacer Standoffs, Laptop Screws for DIY Computer Build, Electronic Projects,
Raspberry Pi, Circuit Board etc.

## To mount the limit switches ##

4x Screws M5x8
4x T-Nut M5 Slot6
4x M2x12 Screws
4x M2 Nut

#####################################################
####
#### Mechanical Parts
####
#####################################################

PLA+ and a little TPU for a small belt.

C12-ER11M-100L ( hollow and needs to be cut to 80mm length )


I used this one that is hollow by default: https://www.amazon.de/dp/B087N5H9T4?
psc=1&ref=ppx_yo2ov_dt_b_product_details
The shaft slides into the bearings and needs one or two shaft collars with 12mm
inner diameter.

2x 6201Z 12x32x10mm bearing ( one is pressed into the top lid and one into the main
tool head )
4x 684ZZ Ball bearings for the printed idler pulley
2m GT2 Timing belt. 6mm width. Use a set that comes with the aluminum clamp mount
block/bar that is needed.

Aluminum extrusions:

Base plate:
160x40 Slot 8; 400mm length; Heavy or Eco variant; M8 Thread on one side in the two
center holes;

Z axis:
1x 120x80 Slot 8mm; 750mm length; Heavy or Eco variant;
1x 20x40 Slot 6mm; 400mm - 600mm length; For more worktravel use 600mm;

Linear rails:

Z-Axis:
HGR15 with 1x HGH15CA sliding block, Same length as the small extrusion; 400mm -
600mm;

Mounting parts:

The big Z Beam rests on the base plate and is connected with two angle brackets and
a aluminum plate at the back.

2x 40x40 90° brackets for Slot 8 profiles


1x 150x80x10 Aluminum plate

Some T-Nuts for Slot 8 and 6 slots:

20x Slot-8 M8
20x Slot-6 M6
Slot-6 M3 (number depends on the length of the linear rail)

A package of setscrews and a box of different hex screws. M2, M3, M4. Also some M6
and M8 Screws are needed.
T Slots Nuts for M6, M8, M4. I don't use the small ones. Only the heavy squaretype
ones.
M8 and M6 screws. Don't know the exact size
M8
4x M8x18
6x M8x25
6x M8x30
M6
12x M6x15

M3
M3x8 ( number of screws depends on the linear rail length you choose )

Stepper:

Z-Axis:

# Dual shaft stepper for the spindle and wire rewinder


Nema 17; 0.4Nm; 1.68A; 1.8° Step angle; 5mm shaft; Rated 2.8v; DUAL SHAFT is needed
if the machine is used with the wire extension!
The stepper I use: SY42STH47-1684B

# Stepper for the axis


Nema 17 planetary gearbox; 19.2:1; 8mm shaft; ( if you can't get the exact 19,2:1
gear ratio you can use 19:1 or similar; This can be adjusted in the software)
https://www.reichelt.de/schrittmotor-hoch-drehmoment-hybrid-2-phasen-nema17-01-
p219027.html?&trstct=pos_0&nbc=1

For the strong roundbar drill jig an aluminum tube is needed with 40mm OD and 32mm
ID. Currently only supports 12mm round bars.

This list may not be complete. Some screws and maybe other parts needed could be
missing here.

# XY Axis

2x Nema 17; 0.4Nm; 1.68A; 1.8° Step angle; 5mm shaft; Rated 2.8v; I use:
17SY42STH47-1684A

https://www.reichelt.de/schrittmotor-hoch-drehmoment-hybrid-2-phasen-nema17-01-
p219027.html?&trstct=pos_0&nbc=1

* Linear rails
* 1x HGR20 500mm + 2x HGH20CA linear block + SFU1605 Ballscrew 450mm ( ~80.- )
* 1x HGR20 300mm + 2x HGH20CA linear block + SFU1605 Ballscrew 250mm ( ~80.- )

* Aluminum
* 1x 150mm x 530mm x 15mm ( ~70.- )
* 1x 150mm x 260mm x 15mm ( ~40.- )
#####################################################
####
#### Wire EDM extension V2
####
#####################################################

Bearings:

2x MR63ZZ 3x6x2.5mm
7x V623ZZ 3x12x4mm bearings

4x 696-2RS Kugellager seald 6x15x5mm


https://www.amazon.de/dp/B09V5DBM6Y?psc=1&ref=ppx_yo2ov_dt_b_product_details

4x v groove bearing 6x30x8mm (2.5mm groove depth. They are sold as 8mm width but
the center is 9mm and only the outer ring is 8mm. Integrated washers)
https://www.amazon.de/dp/B076VCCCMS?psc=1&ref=ppx_yo2ov_dt_b_product_details

2x Pneumatic fittings with M10 thread


https://www.amazon.de/dp/B07DGLCJ4Z?psc=1&ref=ppx_yo2ov_dt_b_product_details

1x set with 3D printer nozzles

You might also like