GAIN Controls display adjustments. DISPLAY Controls display mode windows.

GAIN controls for background noise (speckle). - Press for display mode and soft keys display.
SEA controls sea clutter. - Press again to toggle through display modes, and ENTER
RAIN controls rain clutter around the vessel. - Press and hold for 2 seconds for full page radar display.
FTC controls rain clutter at a distance. Monochrome
- Press for soft keys display. WINDOWS SELECT ZOOM
OFF ON WINDOW OFF ON
MANUAL MANUAL
O O
F F 50%
F 75%
F
Press soft key to toggle window on/off, or return to full screen.
FTC RAIN SEA GAIN
Zoom: Move Zoom box using trackpad, press ENTER to finish.
Color
WINDOWS SELECT
OFF ON WINDOW ZOOM...
Select a slider using the soft key or trackpad.
Toggle between Auto/Man or off/on by pressing soft key again.
Soft Key Labels:
Adjust slider using trackpad, and press ENTER to finish.
Change when you press a key.
Default soft key labels are shown. Press soft key to toggle window on/off, or return to full screen.
Zoom: Press ZOOM key to display zoom window option.
VRM/EBL Used to measure range and bearing to/between targets. Move Zoom box using trackpad, press ENTER to finish.
- Press to place VRM/EBL if one not already placed.
Adjust position using trackpad, and press ENTER to finish.
- Press to display soft keys if VRM/EBL already placed. MARKS / MOB Controls placing marks, and Man
Overboard function.
VRM/EBL
VRM/EBL1 VRM/EBL2 DATABOX - Press to place mark at cursor position, and use trackpad
OFF ON OFF ON FLOAT! OFF ON
to move mark. Press ENTER to finish.
- Press and hold for 2 seconds to activate or cancel MOB.

Use soft key to toggle VRM/EBL on or off. Soft keys

RANGE Controls range scale. Range scale and range rings are
Press FLOAT to access float options for existing VRM/EBL. Press to select option, or highlight option or slider.
shown in the Status Bar.
Press VRM/EBL DATABOX to toggle data box display off/on. Labels change when you press soft/dedicated key.
- Press top of key to increase the range scale.
Elipses (...) after the text indicate that pressing soft
- Press bottom of key to decrease the range scale.
key leads to a further display of soft key options.
- Press and hold to change the scale faster.
MULTI Controls guard zone alarm sensitivity, and tuning the receiver.
Also controls display lighting and contrast (monochrome) or brightness ENTER
(color). Confirms selection and (if appropriate) clears current ALARMS Used to control guard zones.
- Press to display sliders. soft key labels. It either performs the selected task, - Press to place guard zone if one not already placed.
accepts changes, or leads to display of more options. Adjust size/shape using trackpad, press ENTER to finish.
Monochrome When cursor text is displayed, takes cursor control - Press to display soft keys if guard zone already placed.
of the object.
ON GUARD 1 GUARD 2
When arrow-head cursor symbol is displayed, drops OFF ON OFF ON
O A
F U the object under cursor control.
25% F 25% T
O
ALARM LIGHT CONTRAST TUNE CLEAR
Cancels operation in progress and returns to the Use soft key to toggle zone on or off.
previous display. Adjust size/shape using trackpad, and press ENTER to finish.
Deletes an object/function under cursor control.
Color - Press and hold MULTI key for brightness to 100%. MENU Provides access to setup options.
ON
Trackpad - Press to display soft keys.
A Controls cursor position on the screen, and also the sliders
75% SYSTEM RADAR
25%
U and setup options. SET UP¬ SET UP¬
T
O Hold the trackpad down to move the cursor faster.
ALARM LIGHT TUNE

POWER
Select a slider using the soft key or trackpad. Press and hold until unit beeps to turn on display. Press soft key to display required setup menu, then use trackpad
Toggle between Auto/Man or off/on by pressing key again. Press to toggle between Standby and Transmit. to select option and soft key to change setting.
Adjust slider using trackpad, and press ENTER to finish. Press for 3 seconds to turn off display. Press ENTER to close menu, and CLEAR to to finish.
D3994-5

Quick Reference Card: HSB Series LCD Radar Displays

86032_2
Default Display Default Soft Keys
Status Bar
RR AUTO NORTH UP COURSE UP HEAD UP
3nm 1/2 126°T H-UP T IR
Range rings
The number and
spacing depend on
Targets: Press the required soft key to change the heading mode, and press ENTER.
the current range, or
you can turn them off
INT REJ EXPANSION WAKES CLEAR
Landmass Ship's Heading OFF ON OFF ON OFF S M L WAKES
Marker (SHM)
You can hide this
temporarily
Press the soft key to toggle INTerference REJection or Target
Cursor position, EXPANSION on/off.
Channel buoy controlled by the Press the WAKES soft key until the required option (short, medium or long
trackpad wakes, or OFF) is highlighted. Press ENTER to accept.
Press CLEAR WAKES to clear existing wakes from the display.
Ship's position
Surface You can move this
vessel off-centre if required CRSR BOX RNGE RNGS DATABOXES WAYPOINT
OFF ON OFF ON OFF ON OFF ON

Bearing scale,
each tick indicating
Press the appropriate soft key to toggle on/off Cursor Readout Databox,
10˚ of azimuth
Range Rings, Data Boxes or Waypoint display, and press ENTER to accept.
CURSOR
BRG 045° R Cursor position box
Shows the current
RNG 0.28 nm cursor position as
either Range/Bearing Context Sensitive Cursor Control
HDG MODE TARGETS SCREEN or Lat/Long. You can
move this box to your When the cursor is positioned over special features on the display, a text label appears
preferred position to identify the feature. Depending on the feature, you can then move, re-size or delete it.
on the screen, or
Default soft key labels turn it off. Move (for example, an EBL) Text Label Feature
These can be turned off; press any soft key to re-display them. BOX Data box (any type)
1. CTR Radar centre
Different labels are displayed when you press a key.
EBL Electronic Bearing Line
FLT Floating VRM/EBL
Status Bar GRD Guard zone corner or side
Selected range, Range rings Current heading Mode Indicators MRK Mark
in nautical miles (on/off) if heading data available, displayed when function set on: SHM Ship's Heading Marker
or Course Over Ground. VRM Variable Range Marker
Auto mode Target
Can be displayed in 2.
degrees Magnetic or True Gain, Sea Expansion VRM/EBL VRM and EBL
and/or Tune Wakes Guard Zone ZMB Zoom box
Alarms

3. Delete (for example, an EBL)

RR AUTO WKS EX GZ 1.
3nm 1/2 126°T H-UP GST FTC RC IR

Range ring interval Heading mode Rain

Not displayed if Normally Head Up (H-UP), Clutter
range rings are off but you can select
4.

86032-1B
Course Up (C-UP) or 2.
North Up (N-UP) if FTC Interference
you have heading data (Remote rain) Rejection