TECHNICAL

DATA BOOK

A Quick Reference
Book of Formulas,
Charts and Tables

A SUPERIOR ENERGY SERVICES COMPANY

©2007 Wild Well Control, Inc.

The information contained herein has been collected

from various sources. Accordingly, Wild Well Control,
Inc. cannot and does not guarantee, warrant or represent
the accuracy of or accept any responsibility for the use
of any information contained herein.
 Acronyms & Abbreviations
3
Unless otherwise defined, the following
abbreviated terms are used in this book. Units are
identified within specific formulas and equations.
Term Description
bbl Barrel
bpm Barrels per minute
Cap Capacity
Csg Casing
DC Drill collar
Disp Displacement
DP Drillpipe
DS Drillstring
ECD Equivalent circulating density
Eff Efficiency
EMW Equivalent mud weight
EOB End of build
FCP Final circulating pressure
FMDPP Final maximum drillpipe pressure
FP Formation pressure
ft Foot
gal Gallon
gpm Gallons per minute
HP Hydrostatic pressure
ICP Initial circulating pressure
ID Internal diameter
IMDPP Initial maximum drillpipe pressure
KOP Kick off point
KWM Kill weight mud
MD Measured
depth min Minutes
MW Mud weight
OD Outer diameter
OMW Original mud weight
pcf Pounds per cubic foot
PP Pump pressure
ppf Pounds per foot
ppg Pounds per gallon
psi Pounds per square inch
PV Plastic viscosity
Q Flow rate
SF Safety factor
SICP Shut in casing pressure
SIDPP Shut in drillpipe pressure
sk, Sack, sacks
sx
SPM Strokes per minute
SPP Slow pump pressure
stk Stroke
TVD True vertical depth
V Velocity
Vol Volume
YP Yield point
2 Table of Contents
Acronyms & Abbreviations.................................................................................. 2
Common Formulas & Equations
Capacities & Volumes for Downhole ............................................................... 4
Capacities & Volumes of Tanks........................................................................ 5
Pump Output & Rate Formulas ......................................................................... 6
Pump Pressure Relationships ............................................................................ 6
Equivalent Circulating Density ......................................................................... 7
Trip Calculations ............................................................................................... 7
Pressure & Gradient Formulas .......................................................................... 8
Kick Related Formulas & Equations
Kill Sheet Calculations...................................................................................... 9
Kick Related Formulas.................................................................................... 10
Kick Related Engineering Calculations .......................................................... 11
Volumetric Method Calculations .................................................................... 12
Lubricate & Bleed Calculations ...................................................................... 12
Bullheading Calculations ................................................................................ 13
Stripping / Snubbing Calculations................................................................... 13
Subsea Formulas ............................................................................................. 14
Accumulator Sizing......................................................................................... 14
Mud & Cement Formulas................................................................................ 15
Hydraulics Formulas ....................................................................................... 17
Estimates & Rules of Thumb
Tripping........................................................................................................... 17
Stuck Pipe........................................................................................................ 18
Free Point and Stretch Estimates..................................................................... 19
Temperature Drop Across Choke or Orifice ................................................... 20
Bit Nozzle Pressure Loss.....................................................................................
Gas Well Flow Rates....................................................................................... 20
Area of a Circle ............................................................................................... 21
Force and Pressure .......................................................................................... 21
Weight of Spiral Drill Collars ......................................................................... 21
Buoyancy Factor ............................................................................................. 21
Surface and Bottom Hole Pressures in Full Gas Column ............................... 23
Pipe Elongation Due to Temperature ..................................................................
Piping & Other Data Tables
Drillpipe – Range II......................................................................................... 24
Drillpipe Capacity & Displacement ................................................................ 25
Heavy-Weight Drillpipe .................................................................................. 26
Drill Collars..................................................................................................... 27
Drill Collar Capacity & Displacement ............................................................ 29
KILL SHEET................................................................................................. 30
API Tubing ...................................................................................................... 32
Premium Connection Tubing .......................................................................... 38
Casing Strength ............................................................................................... 40
Casing Capacity............................................................................................... 43
Hole Capacity.................................................................................................. 45
Triplex Pumps at 100% Efficiency ................................................................. 46
Mud Weight Adjustments ............................................................................... 48
Mud Weights ................................................................................................... 49
Specifications for BOP Flanges, etc. .............................................................. 51
Gate Valve Data .............................................................................................. 52
API Ring Joint Flanges ................................................................................... 54
BOP Fluid Operating Volumes ....................................................................... 57
Coiled Tubing Data ......................................................................................... 61
Coiled Tubing Dimensions.............................................................................. 62
Electric Line .................................................................................................... 65
Wireline Data .................................................................................................. 66
Conversion Factors.......................................................................................... 67
4 Formulas & Equations

Capacitie
cities & Vol
Volume
umes for Downhol
Downhole
e
Capacities
Open Hole Capacitybbl/ft (OHCap) =
2
(Hole Diameter inches)
1,029.4

(Casing ID inches)2
Casing Capacitybbl/ft (CsgCap) =
1,029.4

2
(Pipe ID inches)
Drill String Capacitybbl/ft (DSCap) =
1,029.4

OH x DS Annular Capacitybbl/ft (OH x DSCap) =

(HoleDiameterinches)2 − (ODStringinches)2
1,029.4

Csg x DS Annular Capacitybbl/ft (Csg x DSCap) =

(Casing IDinches)2 − (ODStringinches)2
1,029.4
Multiple String Annular Capacitybbl/ft (MSACap) =
(Casing ID inches)2 − ⎡(ODPipe1inches)2⎢ + (ODPipe2inches)2 ⎤
⎣
⎥⎦
1,029.4
Volumes per Section
Open Hole Volumebbl (OHVol) = OHCapbbl/ft x Lengthft

Casing Volumebbl (CsgVol) = CsgCapbbl/ft x Lengthft

Drill String Volumebbl (DSVol) = DSCapbbl/ft x Lengthft

OH x DS Annular Volumebbl (OH x DSVol) =

(OH x DSCap)bbl/ft x Lengthft

Csg x DS Annular Volumebbl (Csg x DSVol) =

(Casg x DSCap)bbl/ft x Lengthft

Multiple String Annular Volumebbl (MSAVol) =

MSACapbbl/ft x Lengthft
 Formulas & Equations
5

Capacitie
cities & Vol
Volume
umes of Tanks
Vertical Cylindrical Tanks

Capacitybbl/ft = (Tank Diameterft )2

7.148

Capacitybbl/ft = (Tank Diameterinches )2

1,029.4

Capacitybbl/inch = (Tank Diameterft )2

85.78

Capacitybbl/inch = (Tank Diameterinches )2

12,352.9
Volumebbl = Capacitybbl/ft x Heightft
Volumebbl = Capacitybbl/inch x Heightinches

Rectangular Tanks Capacitybbl/ft = 0.178

x Lengthft x Widthft Capacitybbl/inch = 0.0148
x Lengthft x Widthft Volumebbl =
Capacitybbl/ft x Heightft Volumebbl =
Capacitybbl/inch x Heightinches
Horizontal Cylindrical Tanks

Volume of Tankbbl = Lengthft ×(Tank Diameterinches )

2

1,029.4

Content from Volume (for Horizontal

Tanks)
Height of Contentinches
Height Ratio =
Height of Tankinches

FIND VOLUME FACTOR FROM TABLE USING CALCULATED HEIGHT

RATIO:
Content in Tankbbl = Vol of Tankbbl x Volume Factor
Height Volume Height Volume
Ratio Factor Ratio Factor
0.05 0.019 0.55 0.560
0.10 0.052 0.60 0.626
0.15 0.092 0.65 0.690
0.20 0.142 0.70 0.747
0.25 0.195 0.75 0.800
0.30 0.252 0.80 0.857
0.35 0.310 0.85 0.900
0.40 0.373 0.90 0.948
0.45 0.430 0.95 0.980
0.50 0.500 1.00 1.000
6 Formulas & Equations

Pump Outp
Output & Rate Formula
ormulas
s
Pump Outputs
FOR TRIPLEX PUMPS:
Outputbbl/stk =
0.000243 x (Liner IDinches)2 x Strokeinches x Eff
%
FOR DUPLEX PUMPS (DOUBLE ACTING):
Outputbbl/stk =
0.000162 x [2 x (Liner IDinches)2 – (Rod
ODinches)2]
Pump Rates
Ratebpm = Outputbbl/stk x SPM
Rategpm = 42 x Outputbbl/stk x SPM

Pumping/Spotting/Displacing

BBL to Pump
Timemin =
Outputbbl/stk × SPM

Pump Pressure Relati

elatio
onsh
nships
New Pump Pressure (PP) for Rate
Change
2
⎛ New Ratebpm ⎞
New PPpsi = ⎜ ⎟ × Old PPpsi
⎝ Old Ratebpm ⎠

2
⎛ New SPM ⎞
New PPpsi = ⎜ ⎟ × Old PPpsi
⎝ Old SPM ⎠

New Pump Pressure (PP) for Density Change

New MWppg
New PPpsi = × Original PPpsi
Original MWppg
 Formulas & Equations
7

Equivale
Equivalent
nt Circula
Circulating
ting Density
(ECD)
Equivalent Circulating
Density
(ECDppg) using Pressure
Loss
Annular Friction Pressure
ECDppg = MWppg +
Losspsi
0.052 × TVDft
Where:
Annular Friction Pressure Loss in psi is
approximately equal to 10% of the pump
pressure for normal hole geometries (i.e., no
liners or tapered strings).

Equivalent Circulating Density (ECDppg)

using Yield Point (YP) for MW ≤ 13 ppg
0.1× YP
ECDppg = MWppg+
HoleDiameterinches -
PipeODinches
Where:
YP = Fann 300 reading – PV
PV = Fann 600 reading – Fann 300 reading

Equivalent Circulating Density (ECDppg)

using Yield Point (YP) for MW > 13 ppg
0.1
ECDppg = MWppg +
HoleDiameterinches −
PipeODinches
⎛ PV × Vft/min ⎞
× YP +
⎜ ⎟
300× − PipeOD )
(HoleDiameter

Trip Calcu
alcula
lations
tions
Trip
Marginppg
- Pipe ODinches)
Trip Marginppg =
YPmud
11.7 × (Hole
Diameterinches
Annular Pressure
Trip Marginppg Losspsi
=
0.052 ×
TVDft
Slug Mud Weightppg for a given Length of Dry
Pipe
Slug Weightppg
=
MWppg +
(MWppg × Length Dry Pipeft × DP Capbbl/ft )
Volume of Slugbbl

Slug Volumebbl for a given Length of Dry Pipe

MWppg × Length Dry Pipeft × DP Capbbl/ft
Slug Volumebbl
= Slug MWbbl - MWppg
8 Formulas & Equations

Trip Calcu
alcula
lations,
tions, continue
continued
Pit Gain from Slugbbl
Slug Weight ppg - MWppg
Pit Gainbbl = Slug Volumebbl ×
MWppg

Depth Slug Fallsft

Pit Gain from

Slug
Depth Slug Falls =bbl ft
DP Capbbl/ft

Hydrostatic Pressure Drop per Vertical

Foot
(ΔPpsi/ft) when Pulling Dry Pipe
0.052 x MWppg x DP Displ bbl/ft
ΔPpsi/ft =
Annulus Capbbl/ft + DP Capbbl/ft
Hydrostatic Pressure Drop per Vertical Foot
(ΔPpsi/ft) when Pulling Wet Pipe
(DP Capbbl/ft + DP Displbbl/ft )
ΔPpsi/ft = 0.052 x MWppg x
Annulus Capbbl/ft

Length of Dry Pipe Pulled Before Fill-

Up for Desired Pressure Drop ΔP
ΔPpsi × (Annulus Capbbl/ft + DP Capbbl/ft )
Lengthft =
0.052× MWppg × DP Displ bbl/ft

Length of Wet Pipe Pulled Before Fill-

Up for Desired Pressure Drop ΔP
ΔPpsi × Annulus Capbbl/ft
Lengthft =
0.052 ×MWppg × (DP Capbbl/ft + DP Displ bbl/ft)

Pre
Pressure & Gra
Gradie
dient Formula
Formulas
s
Fluid Gradient (Gradientpsi/ft)
Gradientpsi/ft = 0.052 x Fluid Densityppg
Gradientpsi/ft = 0.007 x Fluid Densitypcf
Gradientpsi/ft = 0.433 x Specific Gravity (SG)

Hydrostatic Pressure (HPpsi)

HPpsi = Gradientpsi/ft x TVDft HPpsi
= 0.052 x MWppg x TVDft HPpsi =
0.007 x MWpcf x TVDft HPpsi =
0.433 x SG x TVDft
 Formulas & Equations
9

Kill Sheet
eet Calcu
alcula
lations
tions
(All
All formul
formulas based on sing
ingle bubble in wate
water based
ased
SEE SAMPLE KILL SHEET ON PAGE 30/3
30/31
1.
Kill Weight Mud (KWMppg) from
Original Mud Weight (OMWppg)
SIDPP psi
KWMppg = + OMWppg
(0.052 × TVDft)
Initial Circulating Pressure (ICPpsi)
ICPpsi = SIDPPpsi + SPPpsi

Final Circulating Pressure (FCPpsi)

SPPpsi × KWMppg
FCPpsi = OMWppg

Strokes to Bit (STB)

Drillstring Volumebbl
STB =
Outputbbl / stk

Strokes for KWM to Shoe

Openhole Annular Volumebbl

Strokes to Shoe = Outputbbl/stk +
STB

Strokes for KWM to Surface

Total Annular Volumebbl

Strokes to Surface = Outputbbl/stk +
STB

Time for KWM to Bit

STB
Time to Bitmin =
SPM

Time for KWM to Shoe

Strokes to Shoe
Time to Shoemin =
SPM

Time for KWM to Surface

Strokes to Surface
Time to Surface =
SPM
10 Formulas & Equations

Kick Relat
elated
Form
Formulas
las
Length of
Influx
Influx Sizebbl
Influx Length
ft =
Lower Annulus Capbbl/ft
Expected Pit Gain (MPGbbl)
with a
Gas Kick in Water-Based Mud
Systems
FPpsi × Original Gain bbl × Annular
MPG bbl = 4 × Surface Pressure (MSP
Expected psi) from
a
Gas Kick in Water-Based Mud
Systems
FPpsi ×Original Gain bbl
Maximum Allowable Mud Weight
(MAMWppg)
Applied
ppg Pressurepsi
MAMW MW=ppg + Test
0.052 ×
Maximum Allowable
Shut-In
Casing Pressure
(MASPpsi)
Kick Tolerance (KTppg) with Influx
⎡ TVDshoe ⎤
KTppg = ⎢ (MAMWppg − MWppg) × ⎥
⎣ TVDft ⎦
⎡ Influx
– (MWppg − MWIppg ) ×
HeightVDft ⎤
Where: ⎢
MWIppg = Density of influx (ppg)

Estimated Kick
Density
SICPpsi −
Kick Densityppg = MWppg −
SIDPP psi
0.052 × Kick
SICP psi −
Kick Gradientpsi/ft = (MWppg × 0.052) −
SIDPP psi
Gas Migration Distance
Rise in SICP
psi
DistanceTVDft = MWppg × 0.052

Rate of Gas
Migration
Distance of
Migration Rate =
 Formulas & Equations
11

Kick Relat
elated Enginee
Engineering
ring
(All
All formul
formulas based on sing
ingle bubble in wate
water based
ased
Bottom Hole Pressure (BHPpsi) while
Circulating on the Choke
BHPpsi = Hydrostatic Pressurepsi Mud in
Drillstring
+ SIDPPpsi
Equivalent Mud Weight (EMWppg) at Bottom
Hole while Circulating out a Kick

EMWBHPpsi ppg=
0.052 × TVD ft

Shut-In Casing Pressure (SICPpsi)

SICPpsi = SIDPP psi + [0.052 × (MWppg − Kick
Density ppg )
x Length of InfluxVDft
Formation Pressure (FPpsi)
FPpsi = SIDPPpsi + [0.052 x OMWppg x
TVDft]
FPpsi = SICP + 0.052 x [(Kick LengthVDft x Kick
Densityppg)
% Reduction in Hydrostatic Pressure Due to
Gas- Cut Mud (GCMW) %ΔPgcm (for water-base
mud)
100 × (OMWppg − GCMWppg )
%ΔPgcm =
GCMWppg
Leak-Off Test Pressure (LOTpsi) and
Equivalent Mud Weight (EMWLOT) at
Shoe
LOTpsi = 0.052 x Test MWppg x
TVDshoe
+ Applied Pressure to Leak-Offpsi
LOTpsi
Formation EMW =
Integrity Test Pressure (FITpsi)
and
Equivalent Mud Weight (EMWFIT) at
Shoe
FITpsi = 0.052 x Test MWppg x
TVDshoe
+ Applied Integrity Pressurepsi

Maximum Formation Pressure that

can be Controlled with a Well Shut-In
Max FPpsi = 0.052 x (KTppg + MWppg) x
TVDft
12 Formulas & Equations

Kick Relat
elated Enginee
Engineering
ring
Calcu
alcula
latio
tion
ns, continue
continued
(All
All formul
formulas based on sing
ingle bubble in wate
water based
ased
mud.)
Maximum Kick Height Possible
not to Exceed MASP
MASP
Kick HeightVDft =
Mud Gradient psi/ft - Kick Gradient psi/ft

Maximum Kick Volume Possible

not to Exceed MASP
Kick Volumebbl = Kick Heightft x Annulus Capbbl/ft

Vol
Volume
umetric Method Calcu
alcula
lations
tions
Initial Pressure Build Increment (ΔIP)
ΔIPpsi = Safety Marginpsi + Rangepsi

Cycle Pressure Build Increment

(ΔCP)
ΔCPpsi = Rangepsi
Hydrostatic Pressure (ΔHPLpsi/bbl) Loss per
Barrel of Mud Bled in Upper Annulus

Gradient Mud
psi/ft
ΔHPLpsi/bbl Annulus
= Capbbl/ft at top of hole

Bleed Volume (bbl) per Cycle

ΔCPpsi
Volbleed =
ΔHPLpsi / bbl

Lubrica
ubricate & Bleed
Bleed Calc
alculations
lations
Cycle Hydrostatic Pressure Gain (ΔHPpsi/bbl)
per
Barrel of Mud Pumped in Upper Annulus
Gradient Lube Mud psi/ft
ΔHPpsi/bbl Annulus
= Cap bbl/ft at top of hole
Cycle Hydrostatic Pressure Increase (ΔHPIpsi)
or
Lubricated Volume (ΔVOLbbl) to be Bled
Off
Gradient Lube Mud psi/ft x ΔVOL
ΔHPIpsi =
ΔHPI psi x Annulus Cap bbl/ft at top of hole
ΔVOLbbl =
Gradient Lube Mud psi/ft
 Formulas & Equations
13

Lubrica
ubricate & Bleed
Bleed Calc
alculations
lations
Simplified Equation for Lubrication
2
P3 = P
1
P2
Where:
P1 = Original shut in pressure
P2 = Pressure increase due to pumping lubricating
fluid into the well bore (increase due to
compression)
P3 = pressure to bleed down after adding the
hydrostatic of the lubricating fluid
Procedure:
1. Select a working pressure range, Pw.
Recommended Pw = 50-100 psi.
2. Pump lubricating fluid through the kill line to
increase the casing pressure by the working
pressure, Pw.
3. Allow the pressure to stabilize. The pressure
may drop by a substantial amount.
4. Calculate the pressure to bleed down to by using
the formula above.
5. Repeat steps 2 through 4 until all the gas
is lubricated out of the well.

Bullh
llheading
eading Calcu
alcullations
Kill Weight Mud (KMppg)
Formation Pressure psi
KWMppg = 0.052 × Perfs Depth TVDft

Formation Integrity Pressure

(FITpsi) at Perfs Depth
FITpsi = 0.052 x (EMWFIT ppg at perf) x Perfs
TVDft
Hydrostatic Pressure (HPpsi) in Drillpipe
HPpsi = Formation Pressurepsi – SIDPPpsi

Initial Maximum Drillpipe Pressure

(IMDPPpsi)
IMDPPpsi = FITpsi – HPpsi
Hydrostatic Pressure from KWMppg (KMHPpsi)
KMHPpsi = 0.052 x KWMppg x Perfs TVDft

Final Maximum Drillpipe Pressure (FMDPPpsi)

FMDPPpsi = FITpsi – KMHPpsi
14 Formulas & Equations

Stripping/S
Stripping/Snubbing Calcu
alcula
lations
tions
Breakover Point Between Stripping &
Snubbing
Snub Forcelb = Wellbore Pressurepsi
x (DP or DC ODin)2 x 0.7854 + Friction Forcelb

DC Weightlb = DC Weightlb/ft x DC Lengthft

x Buoyancy Factor

DP Weight Required for Breakoverlb

= Snub Forcelb - DC Weightlb

Length of DP Required for Breakoverft =

DP Weight Required for Breakover lb
DP Weight x Bouyancy Factor
lb/ft

Friction Forcelb = Friction Through Pressure

Control
Elements

Influx Height Gain from Stripping Into

Pipe Lengthstrip x (DPCapbbl/ft + DPDispl bbl/ft )
ΔHeightft
= Annulus Capbbl/ft

Casing Pressure Increase

(ΔSICP)
from Stripping into an
Influx
ΔSICPpsi = ΔHeightft x (Gradientmud – Gradientinflux)

Mud Volume to Bleed to

Maintain
Constant Bottom Hole
Pressure
Csg Pressure Incrementpsi x Annulus
BleedMudbbl =
Capbbl/ft
Mud Gradientpsi/ft
 Formulas & Equations
15

Subse
Subsea For
Formula
mulas
s

Riser Differentialpsi
Riser
Differentialpsi =
= 0.052 x [(Riser MWppg – Seawater
Weightppg)
Riser Marginppg
Riser Differential psi
Riser Marginppg =
0.052 × (TVDft - Water Depthft - Air
Gapft )

Pump Start-Up Pressure on Casing Side

Pump Start-Uppsi = SICPpsi – CLFPpsi

Where:
CLFP = Choke Line Friction Pressure (psi)
Initial Circulating Pressure (ICPpsi)
ICPpsi = SIDPPpsi + SPPpsi through the riser

Final Circulating Pressure (FCPpsi)

FCPKWM
= ppg
(SPP through the riser) ×
psi psi
OMWppg

Accum
cumulator
lator Sizing
API Minimum Requirements
100% (S.F.= 1) of fluid volume required to
close and hold closed all preventers and open
an HCR valve
and have a system pressure of 200 psi above
minimum recommended precharge pressure
remaining on the accumulator with pumps off.
Standard Recommendation
150% (S.F.= 1.5) of fluid volume required to
close and hold closed all preventers and open
an HCR valve and have 1,200 psi system
pressure remaining on the accumulator with
pumps off.
Fluid Volume Required
(Volreqd)
Volreq = S.F. x (CloseVolannular +
CloseVolbop1
16 Formulas & Equations

Accum
cumulator
lator Sizing, continue
ontinued
Accumulator Volume Required
Usable hydraulic fluid for operation of blowout
preventer equipment is affected by system
pressure and nitrogen precharge. If the nitrogen
precharge is at the correct (recommended)
precharge, multiply the sizing factor from the
table below times the fluid volume required to
operate a specified number of BOP functions
(Volreq) will provide the required total accumulator
volume.

Accumulato Minimum
r System Recommende Useabl Accumulator
d Precharge e Size Factor*
Pressure
Fluid
Pressure

1,500 750 12.5% 8

2,000 1,000 33.0% 3
3,000 1,000 50.0% 2
5,000 1,000 63.0% 1.
* Based on minimum system pressure of 1,200 psi.

Accumulator Volume Example

If the total fluid required for a BOP stack is 33
gallons, including the safety factor, and the
accumulator has an operating pressure of 3,000
psi with a 1,000 psi minimum precharge, the
accumulator volume required is 33 gallons times
the size factor of 2, or
66 gallons.

Accumulator Usable Fluid

Volume
Usable Volume = VR(Volume Required) x Bottle
Volume
Precharge press Precharge
Where VR = -
press
Min operating Max operating press
press

Mud & Cement

ement Formula
Formulas
s
Barite (100 lb sx) Per 100
bbl
Required for Weight-
Up
KWMppg - OMWppg
Sacks per 100 bbl =
1,470× 35 - KWMppg

Hematite (100 lb sx) Per 100

bbl
 Required for Weight-
Up
KWMppg - OMWppg
Sacks per 100 bbl =
1,680× 40 - KWMppg
 Formulas & Equations
17

Mud & Cement

ement Formula
Formulas,
s, continue
continued
d
Pit Volume Increase per 100 bbl
(ΔV100bbl)
due to Weight-Up with Barite
KWMppg - OMWppg
ΔV100bbl = 100 ×
35 - KWMppg
Final Mud Weight (MWppg) when
Mixing Two Densities of Mud
(Vol1bbl ×MW1ppg) + (Vol2bbl ×MW2ppg)
MWppg =
Vol1bbl + Vol2bbl

Initial Mud Volume Required (IVolbbl) to

Build a Final Volume of Mud with Barite
35 - KWMppg
IVolbbl = Final Volbbl ×
35 - OMWppg

Sacks of (94 lb) Cement Required

5.615cf/bbl x Capbbl/ft x Lengthft x
%Excess
Sacks94lb =
Yieldcf/sk
Mix Fluid Requirement
Mix Fluid Reqgal/sk
Mix Fluidbbl = (No. Sacks to Mix ) ×
42gal/bbl

Balanced Plug (Cement, Barite,

etc.)
a) CALCULATE VOLUME OF PLUG: PlugVolbbl
= LengthPlug ft x Hole Capbbl/ft

b) CALCULATE LENGTH OF BALANCED COLUMN :

PlugVolbbl
LENGTH =
COL FT
Annulus Capbbl/ft + DP Capbbl/ft

c) CALCULATE TOTAL STRING VOLUME TO BALANCE:

VolBalancebbl =
= (Plug Bottom Depthft – LENGTHCOL FT) x DPCapbbl/ft

d) CALCULATE RATIO OF SPACER INSIDE AND OUTSIDE OF

STRING:
Annular Capbbl/ft
Ratiospacer = DP Capbbl/ft

e) CALCULATE DISPLACEMENT VOLUME:

DisplVolbbl = VolBalancebbl – Spacer Behindbbl
18 Formulas & Equations

Hydra
ydraulics Formula
Formulas
s
Annular Velocity (AVft/min)
24.51× Pump Rategpm
Vft/min = 2 2
HoleOD - PipeOD

Hydraulic Horsepower (HHP)

Qgpm x Pump Pressurepsi
HHP =
1,714

Qbpm x Pump Pressurepsi

HHP =
40.8

Rules of Thumb

Tripping Rules
les of Thumb

Ideally, drillers would like to keep bottomhole

hydrostatic pressure constant during the trip out
(POOH)
and the trip in (RIH). However, this is impossible
from the operational standpoint because of swab
and surge pressures. Most tripping rules-of-thumb
are closely associated with maintaining a safe
hydrostatic overbalance that neither causes a kick
nor lost circulation.

Slug Mud Weight Rule of Thumb

Slug mud weight is generally one ppg higher than
the hole mud weight, with the objective being to
unbalance the DP/annulus U-tube by enough to pull
dry pipe. The condition of the mud, related to drill
solids, and/or the mud weight range could
influence the driller to accept less than one ppg.
 Rules of Thumb
19

Stuck Pipe

The causes of stuck pipe are broadly classified as

differential or mechanical, and good monitoring and
operating practices will minimize both types of pipe
sticking. Differential sticking is caused by mud pressure
overbalance and is influenced by drilling practices, type
mud solids, permeability, bottom-hole assembly
clearance, coefficient of friction and the lubricating
characteristics of mud. Mechanical sticking is caused by
deterioration of hole stability (shale problems, hole
cleaning, etc.) and/or directional (crooked-hole)
problems.

Rule of Thumb for Differentially Stuck Pipe

The estimated force required to pull free is equal to
the contact force per unit length, times the length of
pipe in contact with permeable formation times the
coefficient of friction. This estimate tends to be more
accurate in a straight hole than in a directional well.

Estimating Formula for Differential

Sticking
Fdiff = K (ΔP) Area
Where:
K = Sticking coefficient (0.2 water base mud)
(ΔP) = Differential pressure
Area = Contact area
⎛ 12in. ⎞ ⎛ π × d ⎞
Area = L ×⎜ ft ⎟ ⎜ × 3 ⎟
⎝ ⎠ ⎝ ⎠
(assume ⅓ of the drill collar circumference is buried)
Circumference = π x Diameter
Conclusion: Force to pull free increases as the
length of pipe in contact with permeable
formation increases, and as the coefficient
of friction between pipe and wall increases.

Example

Given 6 ¼" DC:

3.1416 × 6.25
π×d = 6.545 (round to 6.5)
3 = 3
ΔP = 200 approx. 0.5 ppg overbalance at 8,000
psi ( ft)
L = 200 ft (of permeable zone)
Fdiff = 0.2 00psi x 200ft x 12in./ft x 6.5in. =
20 Rules of Thumb

Fre
Free Point and Stre
Stretch Estima
Estimates

When the drill string is stuck, the free point method

can be used to estimate the amount of free pipe in
the hole.
Begin by pulling on the pipe with an initial force (Fi)
that is at least 1,000 pounds more than the hanging
weight of the string, and make a reference mark on
the string. Increase the pull by increments (for
example, 5,000 lbs) to final force (Ff) to determine a
measurable stretch. Mark the string again, measure
the distance between
the marks and record as the stretch (S) in inches.
Record the difference between Ff and Fi as the pull
increment
(PI). The amount of free pipe (L) in 1,000’s of feet
below the rotary can then be estimated. These
estimates tend to be more accurate in straight holes
than in directional wells.

Estimating Formula
The formula for free pipe length L is:
2
OD 2
L = 1.9635 × S × −
ID
PI
The formula for pipe stretch S is:
Pl × L
S= 2 2
1.9635 × (OD − ID )

Where:
L = Length of free pipe (1,000s
ft) S = Stretch (inches)
OD = OD of the pipe (inches)
ID = ID of the pipe (inches)
Pl = Pull increment (1,000s lbs) = Ff - Fi
Example
Given:
Drillpipe size = 5", 19.5 lb/ft Fi =
5,000 lb OD = 5"
Ff = 35,000 lb ID = 4.276"
S = 12"
Calculate:
PI = 35 – 5 =
30
25 − 18.284
L = 1.9635 ×12 × = 5.27
thousand feet
30
 Rules of Thumb
21

Estima
Estimating Tempe
mperature Drop
Acros
cross
s a Choke or Orifi
Orifice
ce

Rule of Thumb
The temperature drop across a choke or orifice is
about one degree Fahrenheit (F) per each pressure
drop of one atmosphere (rounded at 15 psi).

Estimating Formula

Tdrop =
(Ph − PL ) psi×1°F
15 psi
Where:
Tdrop = Temperature drop (degrees)
Ph = Gas pressure before the choke (psi)
PL = Gas pressure after the choke (psi)

Example
Calculate temperature drop if the gas pressure
is reduced from 1,000 psi to 500 psi across a
choke.
(1,000 − 500)
Tdrop =
×1°F
15
= 33 x 1°F = 33°F temperature
drop

Bit Nozzl
Nozzle Pre
Pressure Loss
ρQ
Tdrop =
×1°F
Where: 10858
Tdrop = Pressure
(psi) Ph =
Density (ppg)
Q = Circulation rate
(gal/min) A = Area of the
nozzle (in2)
22 Rules of Thumb

Estima
Estimating Gas Well
ell Flow Rates

Rule of
Thumb
The approximate flow rate (in mmscfd) of a gas
well through a blowdown line choke can be
estimated by multiplying 24 hours/day, times the
tubing pressure plus 15, times the square of the
choke size in inches and divide by 1,000.

Estimating Formula

24 x (PL + 15) x (Dch)2

Q=
1,0
Where: 00

Q Flowrate (mmscfd)
=
PL Pressure upstream of choke (psi)
=
Dch Choke size (inches)

Example
Calculate the estimated flowrate of a gas well,
given that tubing pressure is 3,500 psi, and choke
size is 1/4.
2
24 x (3,500 + 15) x (0.25)
Q= = 5.273 mmscfd

1,000

Circle (in2)
Area of a Circl

0.7854 x D2
or π
2
D
or /4
π
Where: R2

D diameter in inch
=
R radius in inch
=
 Rules of Thumb
23

Force and Pre

Pressu
ssure

Force lb = Pressurepsi x Areasq in

Weigh
ight of Spira
Spiral Dril
Drill Collars
llars

ppf for spiral DC

= 0.96 x ppf for smooth DC of same OD & ID

Buoya
uoyancy Factor
Factor (BF)

65.4 − MWppg
BF =
65.4

Surfa
Surface & Bottom Hole
Pre
Pressure
ures in
Ful
Full Gas
Col
Column

Method A – Approximate gas gradient is 0.1 psi/ft

SP = BHP – (0.lpsi/ft x TVDft)

Method B – Exact equation

⎛⎜ 0.01875 × SG × D ⎞ ⎟
⎜ ⎟
SP =BHP x e- Zavg × Tavg
⎠
⎝
Where:
SP = Surface Pressure
(psi)
BHP = Bottom hole pressure
(psi) SG = Specific gravity of
the gas D = Depth in TVD
(feet
Zavg = Average compressibility factor of the
gas
T avg = Average gas temp in degrees Rankine(°F +
460)
24 Rules of Thumb

Pipe Elonga
ongation Due to
Tempe
mperature

Since the well has higher temperatures than the

air above ground, an elongation will take place.

Rule of
Thumb
Pipe will elongate about 0.83 inches, per 100 feet
of length, per 100 degree F increase in
temperature. Knowing the surface temperature
and the average temperature of the well, the
elongation can be estimated.

Note: Elongation (stretch) is also caused by

the hanging weight of pipe.

Estimating Formulas
⎛ 1° F ⎞
BHT = × TVD +
⎜⎟
ST°F
BHT
+ ST Ta =
2
ΔT = Ta – Surface
Temp
in / in
ΔLT = 12in / ft × 0.0000069
× L × ΔT
°
F
Where:
L
Depth = True vertical depth ΔT
ΔLT = × (ft) ×
BHT = Bottomhole temperature (°F)

ST = Surface temperature (°F)

Ta = Average temperature (°F)
ΔT = Change in average temperature (°F)
ΔLT = Elongation (inches)
L = Length of pipe (ft)
 Rules of Thumb
25

My Rule
Rules
s of Thumb
Pipe Nom. Wall Pipe Plain Upset Pipe Pipe Tool Joint with Tool Joint without
API Tool Joint
Size Wt. Thick. ID End Wt. End End ID Length Weight Capacity Displ. Capacity Displ.
Wt. Designation
OD
In. Lb/Ft In. In. Lb/Ft Lb Dia. ID Dia. In. In. Ft. Lb Bbls/Ft Bbls/Ft Bbls/Ft Bbls/Ft
OD
External Upset – Grade
E
2⅞ 10.40 0.362 2.151 9.72 2.40 2.151 3.219 OH 3.875 2.156 1.29 34.99 0.00451 0.00389
0.00449 0.00353
3½ 13.30 0.368 2.764 12.31 4.00 2.602 3.824 NC 38 (IF) 4.750 2.688 1.54 61.10 0.00741 0.00515
0.00742 0.00448
3½ 0.44 2.602 14.63 2.60 3.82 NC 38 5.00 2.56 1.59 0.0065 0.0060 0.00658
15.50 9 2.80 2 4 (IF) 0 3 74.82 8 6 0.00532
Internal External Upset – Grade
X
5 19.50 0.362 4.276 17.93 16.80 3.653 5.188 NC 50 (EH) 6.375 3.500 1.65 120.23 0.01745 0.00784
0.01776 0.00652
External Upset – Grade
G
4 14.00 0.330 3.340 12.93 14.40 3.063 4.625 NC 46 (IF) 6.000 3.250 1.70 108.76 0.01082 0.00587
0.01084 0.00471
4½ 16.60 0.337 3.826 14.98 17.20 3.563 5.188 NC 50 (IF) 6.375 3.750 1.67 113.10 0.01421 0.00663
0.01422 0.00545
Internal External Upset – Grade
G
4½ 20.00 0.430 3.640 18.69 17.60 2.813 4.250 NC 46 (EH) 6.250 2.500 1.71 142.46 0.01252 0.00830
0.01287 0.00680
5 19.50 0.362 4.276 17.93 16.80 3.563 5.188 NC 50 (IF) 6.625 2.750 1.70 157.37 0.01719 0.00827
0.01776 0.00652

2
5 0.50 4.000 15.4 3.31 5.188 5½ 7.25 3.25 1.82 188.1 0.0152 0.0107 0.01554
25.60 0 24.03 0 3 FH 0 0 7 3 5 0.00874
5 25.60 0.500 4.000 24.03 15.40 3.313 5.188 5 ½ FH 7.250 3.500 1.82 179.97 0.01535 0.01066
0.01554 0.00874
5½ 21.90 0.361 4.778 19.81 21.00 3.813 5.563 5 ½ FH 7.250 3.500 1.79 184.41 0.02162 0.00925
0.02218 0.00721

Drillpipe –
Internal External Upset – Grade
S
5½ 21.90 0.361 4.778 19.81 21.00 3.813 5.563 HT 55 7.000 4.000 2.33 199.19 0.02172 0.00925
0.02218 0.00721
5½ 24.70 0.415 4.670 22.54 18.40 3.813 5.563 HT 55 7.000 3.750 2.31 210.15 0.02067 0.01042
0.02119 0.00820
5⅞ 0.36 5.15 7.000 0.0252 0.0097 0.02579
23.40 1 3 4.25 1 1 0.00773
6⅝ 25.20 0.330 5.965 22.19 25.87 5.315 6.929 HT 65 8.000 5.000 2.35 240.81 0.03385 0.01078
0.03456 0.00807
6⅝ 27.70 0.362 5.901 24.21 24.00 5.315 6.929 HT 65 8.000 4.750 2.39 284.15 0.03297 0.01194
0.03383 0.00881
 Drillpipe Capacity
& Displacement
27

ID DP Closed-
DP OD Weight Displacement
Tube Capacity End
(In). (ppf) (bbl/ft)
(In.) (bbl/ft) (bbl/ft)
4.85 1.995 0.00387 0.0016 0.0055
2⅜
6.65 1.815 0.00320 0.0023 0.0055
6.45 2.469 0.00592 0.0021 0.0080
6.85 2.441 0.00579 0.0022 0.0080
2⅞
8.35 2.323 0.00524 0.0028 0.0080
10.40 2.151 0.00449 0.0035 0.0080
8.50 3.063 0.00911 0.0028 0.0119
9.50 2.992 0.00870 0.0032 0.0119
3½ 11.20 2.900 0.00817 0.0037 0.0119
13.30 2.764 0.00742 0.0045 0.0119
15.50 2.602 0.00658 0.0053 0.0119
11.85 3.476 0.01174 0.0038 0.0155
4 14.00 3.340 0.01084 0.0047 0.0155
15.70 3.240 0.01020 0.0053 0.0155
12.75 4.000 0.01554 0.0041 0.0197
13.75 3.958 0.01522 0.0045 0.0197
4½
16.60 3.826 0.01422 0.0055 0.0197
20.00 3.640 0.01287 0.0068 0.0197
16.25 4.408 0.01888 0.0054 0.0243
5 19.50 4.276 0.01776 0.0065 0.0243
20.50 4.214 0.01725 0.0070 0.0243
21.90 4.778 0.02218 0.0072 0.0294
5½
24.70 4.670 0.02119 0.0082 0.0294
23.40 5.153 0.02579 0.0077 0.0335
5⅞ 26.30 5.045 0.02472 0.0088 0.0335
28.67 4.875 0.02309 0.0104 0.0335
22.20 6.065 0.03573 0.0069 0.0426
6⅝ 25.20 5.965 0.03456 0.0081 0.0426
31.90 5.761 0.03224 0.0104 0.0426
7⅝ 29.25 6.969 0.04718 0.0093 0.0565

Note: Capacity and displacement value are

without tool joint.
 2
Nominal Tube Tool Approx.
Nomina Dimensions Joint Weight Make- Capacit Displaceme
l Size Inside Wall Connection Outside Inside Tube up y nt bbls/ft
In. Dia. Thickness Size Dia. In. Dia. In. & Torque bbls/ft
In. In. In. Joints (ft-lb)
3½ 2 /16
1 0.719 NC 38 (3 ½ 4¾ 2 3/16 25.3 9,90 0.004 0.0092

Heavy-Weight
3½ 2¼ 0.625 IF)
NC 38 (3 ½ 4¾ 2⅜ 23.2 0
9,90 2
0.005 0.0084
4 2 9/16 0.719 IF)
NC 40 (4 FH) 5¼ 2 11/16 27.2 0
13,25 0
0.007 0.0100
4½ 2¾ 0.875 NC 46 (4 IF) 6¼ 2⅞ 41.0 0
21,80 3
0.007 0.0149
5 3 1.000 NC 50 (4 ½ 6⅝ 3 1/16 49.3 0
29,40 4
0.008 0.0179
5½ 3⅜ 1.063 IF) 5 ½ FH 7 3½ 57.0 0
33,20 8
0.011 0.0207
6⅝ 4½ 1.063 6 ⅝ FH 8 4½ 70.8 0
46,90 1
0.019 0.0257
 ID 1 ½" 1 ¾" 2" 2 ¼" 2 ½" 2 ¾" 3" 3 ¼" 3 ½" 3 ¾"
OD Capacit 0.0022 0.0030 0.0039 0.0049 0.0061 0.0073 0.0087 0.0103 0.0119 0.0137
4" Wt ylb/ft 36.7 34.5 32.0 29.2 - - - - - -
Disp bbl/ft 0.0133 0.0125 0.0116 0.0106 - - - - - -
4 ¼"
Wt lb/ft 42.2 40.0 37.5 34.7 - - - - Spiral Drill-
Disp bbl/ft 0.0153 0.0145 0.0136 0.0126 - - - - Collars
Wt lb/ft 48.1 45.9 43.4 40.6 - - - - -
4 ½" Approx.
- Displacement of
Disp bbl/ft 0.0175 0.0167 0.0158 0.0148 - - -
4 ¾"
Wt lb/ft 54.3 52.1 49.6 46.8 43.6 - - Spiral
- Drill Collar- in
Disp bbl/ft 0.019 0.018 0.018 0.017 0.015 - - - bbls/ft

Drill
Wt lb/ft 60.8 58.6 56.1 53.3 50.1 - - - -
5" Disp bbl/ft 0.0221 0.0213 0.0204 0.0194 0.0182 - - -⎜⎛ OD 2 - ID 2 ⎟⎞ ×
- - -
Wt lb/ft 67.6 65.4 62.9 60.1 56.9 53.4 - 2.56
5 ¼"
Disp bbl/ft 0.0246 0.0238 0.0229 0.0219 0.0207 0.0194 - - - -
5 ½"
Wt lb/ft 74.8 72.6 70.1 67.3 64.1 60.6 56.8 - - -
Disp bbl/ft 0.027 0.026 0.025 0.024 0.023 0.022 0.020 - - -
Wt lb/ft 282.3 480.1 577.6 574.8 371.6 168.1 764.3 - - -
5 ¾"
Disp bbl/ft 0.0299 0.0291 0.0282 0.0272 0.0261 0.0248 0.0234 - - -
6"
Wt lb/ft 90.1 87.9 85.4 82.6 79.4 75.9 72.1 67.9 63.4 -
Disp bbl/ft 0.0328 0.0320 0.0311 0.0301 0.0289 0.0276 0.0262 0.0247 0.0231 -
6 ¼"
Wt lb/ft 98.0 95.8 93.3 90.5 87.3 83.8 80.0 75.8 71.3 -
Disp bbl/ft 0.035 0.034 0.033 0.032 0.031 0.030 0.029 0.027 0.025 -
Wt lb/ft 6107.0 9104.8 9102.3 999.5 896.3 592.8 189.0 684.8 980.3 -
6 ½"

2
Disp bbl/ft 0.0389 0.0381 0.0372 0.0362 0.0350 0.0338 0.0324 0.0308 0.0292 -
 ID 1 ½" 1 ¾" 2" 2 ¼" 2 ½" 2 ¾" 3" 3 ¼" 3 ½" 3 ¾"

3
OD Capacit 0.0022 0.0030 0.0039 0.0049 0.0061 0.0073 0.0087 0.0103 0.0119 0.0137
6 ¾" Wt ylb/ft 116.0 113.8 111.3 108.5 105.3 101.8 98.0 93.8 89.3 -
Disp bbl/ft 0.042 0.041 0.040 0.039 0.038 0.037 0.035 0.034 0.032 -
Wt lb/ft 2125.0 4122.8 5120.3 5117.5 3114.3 0110.8 6107.0 1102.8 598.3 93.4
7"
Disp bbl/ft 0.0455 0.0447 0.0438 0.0427 0.0416 0.0403 0.0389 0.0374 0.0358 0.0340
7 ¼"
Wt lb/ft 134. 131. 129. 126. 123. 119. 116. 111. 107. 102.
Disp bbl/ft 0
0.0487 8
0.0479 3
0.0470 5
0.0460 3
0.0449 8
0.0436 0
0.0422 8
0.0407 3
0.0390 4
0.0372
Wt lb/ft 144.0 141.8 139.3 136.5 133.3 129.8 126.0 121.8 117.3 112.4
7 ½"
Disp bbl/ft 0.0524 0.0516 0.0507 0.0497 0.0485 0.0472 0.0458 0.0443 0.0427 0.0409

Drill
7 ¾"
Wt lb/ft 154.0 151.8 149.3 146.5 143.3 139.8 136.0 131.8 127.3 122.4
Disp bbl/ft 0.056 0.055 0.054 0.053 0.052 0.050 0.049 0.047 0.046 0.044
Wt lb/ft 0165.0 2162.8 3160.3 3157.5 1154.3 9150.8 5147.0 9142.8 3138.3 5133.4
8"
Disp bbl/ft 0.0600 0.0592 0.0583 0.0573 0.0561 0.0549 0.0535 0.0520 0.0503 0.0485
8 ¼"
Wt lb/ft 176. 173. 171. 168. 165. 161. 158. 153. 149. 144.
Disp bbl/ft 0
0.0640 8
0.0632 3
0.0623 5
0.0613 3
0.0601 8
0.0589 0
0.0575 8
0.0560 3
0.0543 4
0.0525
8 ½"
Wt lb/ft 187.0 184.8 182.3 179.5 176.3 172.8 169.0 164.8 160.3 155.4
Disp bbl/ft 0.068 0.067 0.066 0.065 0.064 0.062 0.061 0.060 0.058 0.056
Wt lb/ft 0199.0 2196.8 3194.3 3191.5 1188.3 9184.8 5181.0 0176.8 3172.3 5167.4
8 ¾"
Disp bbl/ft 0.0724 0.0716 0.0707 0.0697 0.0685 0.0672 0.0658 0.0643 0.0697 0.0609
9"
Wt lb/ft 210. 208. 205. 202. 199. 196. 192. 188. 183. 178.
Disp bbl/ft 2
0.0765 0
0.0757 6
0.0748 7
0.0738 6
0.0726 0
0.0714 2
0.0700 0
0.0685 5
0.0668 7
0.0651
10
Wt lb/ft 260.9 258.8 256.3 253.4 250.3 246.8 242.9 238.8 234.3 229.4
"
Disp bbl/ft 0.095 0.094 0.093 0.092 0.091 0.089 0.088 0.086 0.085 0.083
 Drill Collar Capacity
& Displacement
31

DC OD DC ID DC Capacity Steel Closed-End

(In.) (In.) (bbl/ft) Displ. (bbl/ft)
3 ⅛ 1.250 0.00152 (bbl/ft)
0.0080 0.0095
3 ¾ 1.500 0.00219 0.0115 0.0137
4 ⅛ 2.000 0.00389 0.0126 0.0165
4 ¾ 2.000 0.00389 0.0181 0.0219
6 2.250 0.00492 0.0301 0.0350
6¼ 2.500 0.00607 0.0318 0.0379
6½ 2.500 0.00607 0.0350 0.0410
8 2.813 0.00768 0.0545 0.0622
8¼ 2.875 0.00803 0.0589 0.0661
8½ 2.875 0.00803 0.0622 0.0629
9 2.875 0.00803 0.0707 0.0787
9½ 2.875 0.00803 0.0796 0.0877
10 2.875 0.00803 0.0891 0.0971
10 ½ 2.875 0.00803 0.0991 0.1071
11 2.875 0.00803 0.1095 0.1175
11 ½ 2.875 0.00803 0.1204 0.1285
12 2.875 0.00803 0.1319 0.1399
 Well Data Kick

3
Data
Date SIDP psi | SICP
psi TD | TVD Volume gained
bbl Mud weight ppg Old mud weight (OMW) 281.784.7400 USA
www.wildwell.com
ppg Slow pump psi @ SPM Bit at ft
Fast pump psi @ SPM
Kill Data ("Wait & Weight"
Pump output bbl/stk

Kill
Method)
Kill rate (slow or fast pump) = SPM
Drill String Annulus Capacity
SIDPP
Capacity Kill weight mud (KWM) = OMW + = ppg
Sec. A Sec. F 0.052 × TVD
bbl bbl
Sec. B Sec. G Initial circulation pressure (ICP) = SIDP + Kill rate pressure = psi
bbl bbl
Sec. C Sec. H KWM
bbl bbl Final circulation pressure (FCP) = Kill rate pressure x =
Sec. D
bbl bbl psi
Sec. E OMW
bbl bbl
Total Total Surface to bit strokes | Bit to surface strokes
bbl bbl
One circulation strokes
NOTE: Enlarge page by Kill Schedule ("Wait & Weight"
125% to get 8½ x11" full- Method)
size worksheet.
Strokes Volumes Drillpipe Press Strokes Volume Drillpipe
Press
Casing size 0 0 ICP
Set at

To Bit FCP

Kill
Kill Chart

PRESS
Bit at TD at ft

3
ft
STROKES
 3
T& Wal Inside Coupling Outside Yield Capacit
T&C Grade Thick Resistance T&C T&C T&C T&C
Nomina C l Dia. In. Pressur y
OD In. Upse . In. dia. PSI Non- Upse Non- Upse
l Non Drift e
t Upset t bbl/ft Upset t
In. t-
Upse
lb/ft
Dia In.
Non- Upset Upset PSI Lb bbl/ft bbl/ft
lb/ft Upset In. Rea. Spec In. Lb
In.
1.050 1.14 1.20 H-40 0.113 .824 .730 1.313 1.660 7,680 7,530 6,360 13,300 0.00066
0.00041 0.00044
1.050 1.14 1.20 J-55 0.113 .824 .730 1.313 1.660 10,560 10,560 8,740 18,290 0.00066
0.00041 0.00044
¾
1.050 1.14 1.20 C-75 0.113 .824 .730 1.313 1.660 11,920 24,940 0.00066 0.00041

API
14,410 14,130 0.00044
1.050 1.14 1.20 N-80 0.113 .824 .730 1.313 1.660 12,710 26,610 0.00066 0.00041
15,370 15,070 0.00044
1.315 1.70 1.80 H-40 0.133 1.049 .955 1.660 1.900 10,960 19,760 0.00107 0.00062
7,270 7,080 0.00065
1.315 1.70 1.80 J-55 0.133 1.049 .955 1.660 1.900 15,060 27,160 0.00107 0.00062
10,000 9,730 0.00065
1
1.315 1.70 1.80 C-75 0.133 1.049 .955 1.660 1.900 20,540 37,040 0.00107 0.00062
13,640 13,270 0.00065
1.315 1.70 1.80 N-80 0.133 1.049 .955 1.660 1.900 21,910 39,510 0.00107 0.00062
14,550 14,160 0.00065
1.660 2.30 2.40 H-40 0.125 1.410 1.286 2.054 2.200 5,570 5,270 0.00193
1.660 2.30 2.40 H-40 0.140 1.380 1.286 2.054 2.200
6,180 5,900
1¼ 1.660 2.30 2.40 J-55 0.140 1.380 1.286 2.054 2.200
15,530 26,740 0.00185 0.00084
8,490 8,120
0.00087
1.660 2.30 2.40 C-75 0.140 1.380 1.286 2.054 2.200
21,360 36,770 0.00185 0.00084
11,580 11,070
0.00087
1.660 2.30 2.40 N-80 0.140 1.380 1.286 2.054 2.200
29,120 50,140 0.00185 0.00084
12,360 11,810
0.00087
31,060 53,480 0.00185 0.00084
0.00087
 Tubing Size Normal Weight Threaded Coupling Joint Yield Strength
Displacement
Interna
T& Wall Collapse l
T&C Grade Inside Coupling Outside T&C T&C Capacit T&C T&C
Nomina C Thick Dia. In. Resistanc Yield
l OD In. Upse Drift dia. Non- Upse y Non- Upse
Non . In. e PSI Pressur
t Upset t bbl/ft Upset t
e
In. t-
Upse
lb/ft
Non-
Dia In. Upset Upset PSI Lb bbl/ft bbl/ft
lb/ft Upset In. Rea. Spec In. Lb
In.

1.900 2.75 2.90 H-40 0.145 1.610 1.516 2.200 2.500 5,640 5,340 19,090 31,980 0.00252

API
0.00100 0.00106

1.900 2.75 2.90 J-55 0.145 1.610 1.516 2.200 2.500 7,750 7,350 26,250 43,970 0.00252
0.00100 0.00106
1 1/2
1.900 2.75 2.90 C-75 0.145 1.610 1.516 2.200 2.500 10,570 10,020 35,800 59,960 0.00252
0.00100 0.00106

1.900 2.75 2.90 N-80 0.145 1.610 1.516 2.200 2.500 11,280 10,680 38,130 63,950 0.00252
0.00100 0.00106

2 1/16 2.063 H-40 0.156 1.751 7,770 7,630 0.00298

2.063 J-55 0.156 1.751 7,690 7,280 0.00298

2.063 C-75 0.156 1.751 10,480 9,920 0.00298

2.063 N-80 0.156 1.751 11,180 10,590 0.00298

3
 3
Tubing Size Normal Threaded Coupling Joint Yield Displacement
Internal
Weight Wall Collapse Strength Capacit
T&C Inside Yield
T&C Grade Thick Dia. Coupling Outside dia. Resistanc T&C T&C y T&C T&C
Nominal Non- Drift Pressur
OD In. Upset . In. In. Non Upse Upse
pec I e PSI Non- Upse bbl/ft Non- Upse
In. Upset Dia e PSI
lb/ft U- n. Rt ea. . St n. Upset Lb t Lb Upset t
lb/ft In. pset In
2.375 4.00 H-40 0.167 2.041 1.94 2.875 5,230 4,920 30,130 0.00405 0.0014
7 6
2.375 4.60 4.70 H-40 0.190 1.995 1.90 2.875 3.063 2.910 5,890 5,600 35,960 52,170 0.00387 0.0016 0.00171
1 7

API
2.375 4.60 4.70 J-55 0.190 1.995 1.90 2.875 3.063 2.910 8,100 7,700 49,450 71,730 0.00387 0.0016 0.00171
1 7
2.375 4.60 4.70 C-75 0.190 1.995 1.90 2.875 3.063 2.910 11,040 10,500 67,430 97,820 0.00387 0.0016 0.00171
1 7
3
2 /8 2.375 5.80 5.95 C-75 0.254 1.867 1.77 2.875 3.063 2.910 14,330 14,040 96,560 126,940 0.00339 0.0021 0.00216
3 1
2.375 4.60 4.70 N-80 0.190 1.995 1.90 2.875 3.063 2.910 11,780 11,200 71,930 104,340 0.00387 0.0016 0.00171
1 7
2.375 5.80 5.95 N-80 0.254 1.867 1.77 2.875 3.063 2.910 15,280 14,970 102,99 135,400 0.00339 0.0021 0.00216
3 0 1
2.375 4.60 4.70 P-105 0.190 1.995 1.90 2.875 3.063 2.910 15,460 14,700 94,410 136,940 0.00387 0.0016 0.00171
1 7
0.00216
2.375 5.80 5.95 P-105 0.254 1.867 1.77 2.875 3.063 2.910 20,060 19,650 135,18 177.71 0.00339 0.0021
3 0 0 1
 Tubing Size Normal Threaded Coupling Internal Joint Yield Displacement
Weight Wall Collapse Strength
T&C T&C Inside Coupling Outside dia. Resistanc Yield T&C T&C Capacit T&C T&C
Nominal Grade Thick Drift
OD In. Non- Upse Dia. Pressur Non- Upse y Non- Upse
In. . In. Dia Non Upse Upset e PSI
Upset t In. e PSI Upset Lb t Lb bbl/ft Upset t
In. U- n. Rt . Spec .
lb/ft lb/ft pset ea. In bbl/ft bbl/ft
2.875 6.40 6.50 H-40 0.217 2.441 2.34 3.500 3.668 3.460 5,580 5,280 52,780 72,480 0.00579 0.0023 0.00236
7 3
2.875 6.40 6.50 J-55 0.217 2.441 2.34 3.500 3.668 3.460 7,680 7,260 72,580 99,660 0.00579 0.0023 0.00236
7 3
2.875 6.40 6.50 C-75 0.217 2.441 2.34 3.500 3.668 3.460 10,470 9,910 98,970 135,900 0.00579 0.0023 0.00236
7 3

API
2.875 8.60 8.70 C-75 0.308 2.259 2.16 3.500 3.668 3.460 14,350 14,060 149360 185,290 0.00496 0.0031 0.00317
2 7/8 5 3
2.875 6.40 6.50 N-80 0.217 2.441 2.34 3.500 3.668 3.460 11,170 10,570 105,57 144,960 0.00579 0.0023 0.00236
7 0 3
2.875 8.60 8.70 N-80 0.308 2.259 2.16 3.500 3.668 3.460 15,300 15,000 159,31 198,710 0.00496 0.0031 0.00317
5 0 3
2.875 6.40 6.50 P-105 0.217 2.441 2.34 3.500 3.668 3.460 14,010 13,870 138,56 190,260 0.00579 0.0023 0.00236
7 0 3
2.875 8.60 8.70 P-105 0.308 2.259 2.16 3.500 3.668 3.460 20,090 19,690 209,10 260,810 0.00496 0.0031 0.00317
5 0 3
3.500 7.70 H-40 0.216 3.068 2.94 4.250 4,630 4,320 65,070 0.00914 0.0028
3 0
3.500 9.20 9.30 H-40 0.254 2.992 2.86 4.250 4.500 4.180 5,380 5,080 79,540 103,810 0.00870 0.0033 0.00338
3 1/2 7 5
3.500 10.20 H-40 0.289 2.922 2.79 4.250 6,060 5,780 92,550 0.00829 0.0037
7 1

3
3.500 7.70 J-55 0.215 3.068 2.94 4.250 5,970 5,940 89,470 0.00914 0.0026
3 2
 3
Wall Inside Collapse Capacity
T&C T& Grade Thick. Dia. In. Coupling Outside Resistanc Yield T& T&C T&C
Nomina Drift Pressur
l Non- C dia. e e C T&C
OD bbl/ft
Upse Upse In. PSI Non- Upse Non- Upset
In.
In. t t Dia In.
Non- Upset Upset PSI Upset t Upset
lb/ft lb/ft Upset In. Rea. Spec Lb bbl/ft bbl/ft
In. In. Lb

3.500 9.30 J-55 0.289 2.922 2.797 4.250 7,400 6,990 127,250 0.00829
0.00371

3.500 10.20 J-55 0.289 2.922 2.797 4.250 8,330 7,950 127,250 0.00829

API
0.00371

3.500 7.70 C-75 0.216 3.068 2.943 4.250 7,540 8,100 122,010 0.00914
0.00280

3.500 10.20 C-75 0.289 2.922 2.797 4.250 11,360 10,840 173,530 0.00829
0.00371

3.500 12.70 12.95 C-75 0.375 2.750 2.625 4.250 4.500 4.180 14,350 14,060 230,990 276,120 0.00735
0.00462 0.00471
1
3 /2
3.500 7.70 N-80 0.216 3.068 2.943 4.250 7,870 8,640 130,140 0.00914
0.00280

3.500 10.20 N-80 0.289 2.922 2.797 4.250 12,120 11,560 185,100 0.00829
0.00371

3.500 12.70 12.95 N-80 0.375 2.750 2.625 4.250 4.500 4.180 15,310 15,000 246,390 294,530 0.00735
0.00462 0.00471
3.500 9.20
9.30 P-105
0.254 2.992
2.867 4.250
4.500 4.180
13,050
13,340
208,800
271,970
0.00870
0.00335
0.00338

3.500 12.70
12.95 P-105
0.375 2.750
2.625 4.250
4.500 4.180
20,090
19,690
323,390
386,570
0.00735
0.00462
0.00471
 T&
Tubing Size Normal C Threaded Coupling Joint Yield Displacement
Interna
Weight Wall Collapse Strength bbl/ft
Insid Upset In. Rea.
Coupling Spec
Outside dia. l Yield Capaci T&C
Nomina Non- Grade Thic Drift In. Resistan
l OD In. T&C Upse e In. Pressur Non- Upse ty T&C
Non- Upset
Upset k. In. Dia Non- Upset ce PSI
In. t Dia. e PSI Upset t bbl/ft Upset
lb/ft In. Upset
lb/ft In. Lb Lb bbl/ft
4.000 9.50 H-40
H-40 0.22 4.750 4,05 3,96
6 3.42 0 0 72,00 0.0122 0.0034
4.000 11.00 0.26 3.47 3.35 5.000 4,900 4,590 123,070 0.0040
2 6 1 0.01174 0
4.000 9.50 J-55 0.22 3.54 3.42 4.750 5,110 5,440 99,010 0.0122 0.0034

API
4 6 8 3 3 6
4.000 11.00 J-55 0.26 3.47 3.35 5.000 6,590 6,300 169,22 0.0117 0.0040
2 6 1 0 4 0
4.000 9.50 C-75 4.750 6,350 0.0034
0.22 3.54 3.42 135,010 0.0122 6
4.000 11.0 C-75 0.26 3.47 3.35 5.000 8,410 8,600 230,75 0.0117 0.0040
0 2 6 1 0 4 0
4.000 9.50 N-80
N-80 4.750 6,590 7,910 0.0034
0.22 3.54 3.42 144,010 0.0122 6
4.500
4.000 11.00 0.26 3.47 3.35 5.000 8,800 9,170 246,140 0.0040
2 6 1 0.01174 0
12.60 12.75 H-40 0.27 3.95 3.83 5.200 5.563 4,490 4,220 104,360 0.0152 0.0045
1 8 3 144,020 2 8 0.0046
4.500 12.60 12.75 J-55 0.27 3.95 3.83 5.200 5.563 5,730 5,800 143,50 198,03 0.0152 0.0046
4 1/2 1 8 3 0 0 2 0.0045 4
4.500 12.60 12.75 C-75 0.27 3.95 3.83 5.200 5.563 7,200 7,900 195,68 270,04 0.0152 0.0045 0.0046
1 8 3 0 0 2 8 4

3
4.500 12.60 12.75 N-80 0.27 3.95 3.83 5.200 5.563 7,500 8,430 208,73 288,04 0.0152 0.0045 0.0046
1 8 3 0 0 2 8 4
 Connection Tube

4
Data Inner Make- Data
Outer Outer Inner PSI
Tubing Size Dia. Dia. up Dia. Dia. Drift Wall Cross 100 Ult. Depth Pull Burst Collapse Cap. Disp. Capacity Disp.
In. In. Torque Grade In. In. Thick Sectio % Strengt 100% 100% 100% 100% Gals/1000 ft bbls/ft
¾" CS HYDRIL 1.32 0.68 300 P-110 1.05 0.74 47,600 32,20 26,20 22.

Premium Connection
1.5#
0.64 0.15 0.433 110,00 125,00 31,70 15. 0.0005 0.0003
1" CSP-110
HYDRIL 7
1.60 7
0.86 400 C-75 0
1.31 2
0.95 0.84 0.17 0.639 75,000 95,000 21,30 48,000 0
20,40 17,60 37. 34. 0.0008 0.0008
2.25# C-75
1" CS HYDRIL 0 4 5 7 8 9 0 0 0 4 4 9 2
2.25# N-80/L-
1.60 0.86 400 N-L- 1.31 0.95 0.84 0.17 0.639 80,000 100,00 22,60 51,000 21,80 18,80 37. 34. 0.0008 0.0008
80 CS HYDRIL
1" 0 4 80 5 7 8 9 0 0 0 0 4 4 9 2
2.25# T-95
1.60 0.86 400 T-95 1.31 0.95 0.84 0.17 0.639 95,000 105,00 27,00 60,700 25,90 22,30 37. 34. 0.0008 0.0008
1" CS HYDRIL 0 4 5 7 8 9 0 0 0 0 4 4 9 2
2.25# P-110
1.60 0.86 400 P-110 1.31 0.95 0.84 0.17 0.639 110,00 125,00 31,20 70,300 29,90 25,90 37. 34. 0.0008 0.0008
1" CS HYDRIL 0 4 5 7 8 9 0 0 0 0 0 4 4 9 2
2.25# S-135
1.60 0.86 500 S-135 1.31 0.95 0.84 0.17 0.639 135,00 145,00 38,30 86,200 36,70 31,70 37. 34. 0.0008 0.0008
1-¼" CS HYDRIL 0 4 5 7 8 9 0 0 0 0 0 4 4 9 2
3.02# C-75
1.92 1.21 600 C-75 1.66 1.27 1.18 0.19 0.881 75,000 95,000 21,80 66,000 17,20 15,20 66. 46. 0.0015 0.0011
1-¼" CS HYDRIL 7 8 0 8 4 1 0 0 0 6 2 9 0
3.02# N-80/L-80
1.92 1.21 600 N-L- 1.66 1.27 1.18 0.19 0.881 80,000 100,00 23,50 71,000 18,40 16,20 66. 46. 0.0015 0.0011
1-¼" CS 7 8 80 0 8 4 1 0 0 0 0 6 2 9 0
HYDRIL
1.92 1.21 600 T-95 1.66 1.27 1.18 0.19 0.881 95,000 105,00 27,70 83,700 21,90 19,30 66. 46. 0.0015 0.0011
3.02#CS
1-¼" T-95
HYDRIL 7 8 0 8 4 1 0 0 0 0 6 2 9 0
3.02# P-110
1.92 1.21 600 P-110 1.66 1.27 1.18 0.19 0.881 110,00 125,00 32,00 96,600 25,30 22,40 66. 46. 0.0015 0.0011
1-¼" CS HYDRIL 7 8 0 8 4 1 0 0 0 0 0 6 2 9 0
3.02# S-135
1.92 1.21 600 S-135 1.66 1.27 1.18 0.19 0.881 135,00 145,00 39,40 119,00 31,00 27,50 66. 46. 0.0015 0.0011
1-½" CS 7 8 0 8 4 1 0 0 0 0 0 0 6 2 9 0
HYDRIL
2.16 1.44 800 N-L- 1.90 1.50 1.40 0.20 1.068 80,000 100,00 23,30 85,000 16,80 15,00 91. 55. 0.0021 0.0013
3.64#CS
1-½" N-80/L-
HYDRIL 2 0 80 0 0 6 0 0 0 0 0 8 7 9 3
3.64# P-110
2.16 1.44 800 P-110 1.90 1.50 1.40 0.20 1.068 110,00 125,00 32,30 117,50 23,00 20,70 91. 55. 0.0021 0.0013
1-½" CS HYDRIL 2 0 0 0 6 0 0 0 0 0 0 0 8 7 9 3
3.64# S-135
2.16 1.44 800 S-135 1.90 1.50 1.40 0.20 1.068 135,00 145,00 39,60 144,19 28,42 25,42 91. 55. 0.0021 0.0013
2-1/16" CS 2 0 0 0 6 0 0 0 0 9 1 9 8 7 9 3
HYDRIL
2.33 1.70 900 N-L- 2.06 1.75 1.65 0.15 0.935 80,000 100,00 23,00 75,000 12,10 11,20 125. 49. 0.0029 0.0011
3.25#EUE
2-⅜" N-80/L-
8RD 0 0 80 3 1 7 6 0 0 0 0 0 7 8 8
4.7# N-80/L-80
3.06 1.99 1,500 N-L- 2.37 1.99 1.90 0.19 1.304 80,000 100,00 22,20 104,30 12,80 11,77 162. 71. 0.0038 0.0017
 Connection Data Tube
Outer Inner Make- Outer Inner
Data PSI
Tubing Size Dia. Dia. up Dia. Dia. Drift Wall Cross 100 Ult. Depth Pull Burst Collapse Cap. Disp. Capacity Disp.
In. In. Torque Grade In. In. Thick Sectio % Strengt 100% 100% 100% 100% Gals/1000 ft bbls/ft
2-⅜" PH-6

Premium Connection
2.90 1.80 2,200 N-L- 2.37 1.86 1.77 0.25 1.692 80,000 100,00 22,70 135,00 17,10 15,30 142. 91. 0.0033 0.0021
HYDRIL
2-⅜" PH-6 6
2.90 5
1.80 2,200 RY-85 5
2.37 7
1.86 1.77 0.25 1.692 85,000 100,00 24,10 143,80 0
18,20 16,24 142. 91. 0.0033 0.0021
HYDRIL
5.95#PH-6
2-⅜" RY-85 6 5 5 7 3 4 0 0 0 0 0 2 0 9 7
HYDRIL 2.90 1.80 2,200 T-95 2.37 1.86 1.77 0.25 1.692 95,000 110,00 27,00 160,74 19,66 17,59 142. 91. 0.0033 0.0021
5.95# T-95
2-⅜" PH-6 6 5 5 7 3 4 0 0 0 5 5 2 0 9 7
HYDRIL 2.90 1.80 2,700 P-110 2.37 1.86 1.77 0.25 1.692 105,00 120,00 29,90 178,00 22,50 20,06 142. 91. 0.0033 0.0021
5.95# P-110
2-⅞" EUE 8RD 6 5 5 7 3 4 0 0 0 0 0 0 2 0 9 7
6.5# N-80/L-80 3.66 2.44 2,300 N-L- 2.87 2.44 2.34 0.21 1.812 80,000 100,00 22,30 145,00 12,10 11,16 243. 99. 0.0057 0.0023
2-⅞" PH-6 8 1 80 5 1 7 7 0 0 0 0 0 0 5 9 7
HYDRIL 3.50 2.20 3,000 N-L- 2.87 2.25 2.16 0.30 2.484 80,000 100,00 22,80 198,70 17,14 15,30 208. 133. 0.0049 0.0031
8.7#
2-⅞" N-80/L-80
PH-6 0 0 80 5 9 5 8 0 0 0 0 0 1 1 5 7
HYDRIL 3.43 2.26 3,000 N-L- 2.87 2.32 2.22 0.27 2.254 80,000 100,00 22,80 180,00 15,30 13,90 220. 120. 0.0052 0.0028
7.9# PH-6
2-⅞" N-80/L-80 7 5 80 5 3 9 6 0 0 0 0 0 0 9 4 8
HYDRIL 3.43 2 .265 3,200 T-95 2.87 2.32 2.22 0.27 2.254 95,000 110,00 27,09 214,08 18,00 16,00 220. 120. 0.0052 0.0028
7.9# T-95
2-⅞" PH-6 7 5 3 9 6 0 8 2 0 0 0 9 4 8
HYDRIL 3.43 2.26 3,500 P-110 2.87 2.32 2.22 0.27 2.254 105,00 120,00 29,90 236,00 20,10 18,20 220. 120. 0.0052 0.0028
7.9#
3-½" P-110
EUE 8RD 7 5 2,400- 5 3 9 6 0 0 0 0 0 0 0 9 4 8
9.3# N-80/L-80 4.50 2.99 3,200 N-L- 3.50 2.99 2.86 0.25 2.590 80,000 100,00 22,20 207,20 11,60 10,70 365. 134. 0.0087 0.0032
3-½" EUE 8RD 0 2 3,00 - 80 0 2 7 4 0 0 0 0 0 2 5 0 0
9.3# P-110 4.50 2.99 4,0 P-110 3.50 2.99 2.86 0.25 2.590 110,00 125,00 30,60 284,90 15,90 14,80 365. 134. 0.0087 0.0032
3-½" PH-6 0 2 00 0 2 7 4 0 0 0 0 0 0 2 5 0 0
HYDRIL 4.31 2.68 5,500 N-L- 3.50 2.75 2.62 0.37 3.682 80,000 100,00 22,70 294,50 17,10 15,31 308. 198. 0.0073 0.0047
12.95#
3-½" N-80/L-80 2
PH-6 7 80 0 0 5 5 0 0 0 0 0 4 1 4 2
HYDRIL 4.31 2.68 6,000 T-95 3.50 2.75 2.62 0.37 3.682 95,000 105,00 27,00 386,60 20,30 18,10 308. 198. 0.0073 0.0047
12.95# T-95
3-½" PH-6 3 7 0 0 5 5 0 0 0 0 0 4 1 4 2
HYDRIL 4.31 2.68 7,000 P-110 3.50 2.75 2.62 0.37 3.682 105,00 120,00 29,80 386,60 22,50 20,09 308. 198. 0.0073 0.0047
2 7 0 0 5 5 0 0 0 0 0 0 4 1 4 2

4
12.95#
4-½" P-110
PH-6
HYDRIL 5.12 3.76 8,500 P-110 4.50 3.82 3.70 0.33 4.407 110,00 125,00 31,30 485,00 16,48 14,34 598. 229. 0.0142 0.0054
Casing Weigh Burst Pressure (psi) Collapse Pressure (psi)

4
OD t
(In.) (ppf) H40 J/K 55 C75 N80 C95 P110 H40 J/K 55 C75 N80 C95 P110
9.5 4,380 3,310
11.6 5,350 7,290 7,780 9,240 10,690 4,960 6,100 6,350
4½
7,030 7,580
13.5 6,200 8,460 9,020 10,710 12,410 6,420 8,140 8,540
9,660 10,680
15.1 7,210 9,830 10,480 14,420 7,620 10,390 11,080

Casing
5 14,350
11.5 4,240 3,060
13.0 4,870 6,640 7,090 4,140 4,990 5,140
15.0 5,700 7,770 8,290 9,840 11,400 5,500 6,970 7,250
5½ 8,090 8,830
18.0 6,970 9,500 10,140 12,040 13,940 7,390 10,000 10,490
12,010 13,470
14.0 4,270 5,820 3,120 3,560
6⅝ 15.5 4,810 6,560 7,000 9,620 3,860 4,860 4,990
5,620
17.0 5,320 7,250 7,740 9,190 10,640 4,910 6,070 5,890
6,930 8,520
20.0 6,310 8,610 9,190 10,910 12,640 6,610 8,440 8,830
7 10,000 11,100
23.0 7,270 9,900 10,560 12,540 14,520 7,670 10,400 11,160
12,920 14,520
20.0 28.0 6,060 8,260 8,810 10,460 12,120 6,170 7,830 8,170
4,180 9,200 10,140
6,090 20.0 2,720 3,740 5,100 1,920 2,500 2,660
7,230 23.0 4,360 5,940 6,340 7,530 3,270 3,770 3,830
3,060 4,150
3,480 26.0 4,980 6,790 7,240 8,600 9,960 4,320 5,250 5,320
3,830 5,870 7,220
24.0 29.0 5,610 7,650 8,160 9,690 11,220 5,400 6,760 7,020
5,110 7,820 8,510
6,970 32.0 6,230 8,490 9,060 10,760 12,460 6,460 8,230 8,600
7,440 9,730 10,760
8,830 35.0 6,850 9,340 9,960 11,830 13,700 7,270 9,710 10,180
10,230 11,640 13,020
4,560
5,550
5,550
6,310
6,730
Casing Weigh Burst Pressure (psi) Collapse Pressure (psi)
OD t
(In.) (ppf) H40 J/K 55 C75 N80 C95 P110 H40 J/K 55 C75 N80 C95 P110
26.4 4,140 5,650 6,020 7,150 8,280 3,010 3,280 3,930
7⅝ 3,710 3,900
29.7 6,450 6,890 8,180 9,470 4,670 4,790
5,120 6,180
33.7 5,430 7,400 7,900 8,180 10,860 5,090 6,320 6,560
7,260 7,870
8⅝

Casing
39.0 8,610 9,180 9,380 12,620 8,430 8,820
9,980 11,060
24.0 2,950 950
32.0 2,860 3,930 5,360 5,710 7,860 2,210 2,530 2,950 3,050
9⅝ 3,430
36.0 4,460 6,090 6,490 7,710 8,930 3,450 4,020 4,470
4,360 4,700
40.0 5,020 6,850 7,300 8,670 10,040 4,400 5,350 5,520
6,010 7,420
36.0 2,560 3,520 4,800 5,120 7,040 1,710 2,220 2,320 2,370
10 ¾ 2,470
40.0 3,950 5,390 5,750 6,820 7,900 2,570 2,980 3,530
3,330 3,480
43.5 4,350 5,930 6,330 7,510 8,700 3,250 3,750 3,810
4,130 4,760

4
11 ¾ 47.0 4,720 6,440 6,870 8,150 9,440 3,880 4,630 4,760
5,080 5,310
53.5 51.0 4,030 5,490 5,860 6,960 8,060 2,700 3,100 3,750
7,430 3,490 3,750
7,930 55.5 4,430 6,040 6,450 7,660 8,860 3,320 3,950 4,020
9,410 4,300 4,630
10,900 60.7 4,880 6,650 7,100 8,436 9,760 4,160 5,020 5,160
6,380 5,566 5,860
6,620 65.7 5,330 7,260 7,750 9,200 10,650 4,920 6,080 6,300
7,330 6,950 7,490
7,930 71.1 10,050 11,640
40.5 2,280 8,470 9,280
3,130 47.0 3,070 4,190 1,630 1,620
4,270 54.0 3,560 4,860 2,070 2,380
1,420 60.0 4,010 5,460 5,830 6,920 8,010 2,660 3,070 3,680
1,730 3,440 3,610
1,720
45.5
3,580
4,880
5,210
7,160
2,090
2,410
2,480
2,610
Casing Weigh Burst Pressure (psi) Collapse Pressure (psi)

4
OD t
(In.) (ppf) H40 J/K 55 C75 N80 C95 P110 H40 J/K 55 C75 N80 C95 P110
48.0 1,730 770
54.5 2,730 3,980 5,470 1,140
61.0 3,090 4,220 4,500 1,540 1,660 1,670
13 ⅜ 68.0 3,450 4,710 5,020 5,970 1,950 2,220 2,270
2,330
72.0 3,700 5,040 5,380 6,390 7,400 2,230 2,590 2,880

Casing
2,820 2,880
77.0 5,400 5,760 2,990 3,100
85.0 5,970 6,360 8,750 3,810 3,870
16 4,490
65.0 1,640 670
75.0 2,630 1,010
18 ⅝ 84.0 2,980 1,410
109.0 3,950 7,890 2,560
3,470
20 87.5 1,530 2,110 520 520
106.0 2,740 1,140
94.0 1,530 2,110 520 520
106.5 2,410 770
133.0 3,060 1,500
24 156.0 X-42 1,910 860
26 202.0 X-42 2,120 1,100
30 310.0 X-42 2,450 1,480
36 374.0 X-42 2,040 1,010
 Casing Capacity
45

Casing Weight Casing Capacity Displacement

OD (ppf) ID (bbl/ft) (bbl/ft)
(In.) 9.5 (In.)
4.090 0.0163 0.0035
11.6 4.000 0.0155 0.0042
4½
13.5 3.920 0.0149 0.0049
15.1 3.826 0.0142 0.0055
11.5 4.560 0.0202 0.0042
13.0 4.494 0.0196 0.0047
5
15.0 4.408 0.0189 0.0055
18.0 4.276 0.0178 0.0066
14.0 5.012 0.0244 0.0051
15.5 4.950 0.0238 0.0056
5½ 17.0 4.892 0.0233 0.0062
20.0 4.778 0.0222 0.0073
23.0 4.670 0.0212 0.0084
20.0 6.049 0.0355 0.0071
6⅝ 24.0 5.921 0.0341 0.0087
28.0 5.791 0.0326 0.0102
20.0 6.456 0.0405 0.0073
23.0 6.366 0.0394 0.0084
26.0 6.276 0.0383 0.0095
7
29.0 6.184 0.0372 0.0106
32.0 6.094 0.0361 0.0116
35.0 6.004 0.0350 0.0127
26.4 6.969 0.0472 0.0096
29.7 6.875 0.0459 0.0108
7⅝
33.7 6.765 0.0445 0.0123
39.0 6.624 0.0426 0.0142
24.0 8.098 0.0637 0.0086
32.0 7.921 0.0610 0.0116
8⅝
36.0 7.825 0.0595 0.0131
40.0 7.725 0.0580 0.0146
36.0 8.921 0.0773 0.0131
40.0 8.835 0.0758 0.0146
9⅝ 43.5 8.755 0.0745 0.0158
47.0 8.681 0.0732 0.0171
53.5 8.535 0.0708 0.0195
46 Casing Capacity

Casing Weight Casing Capacity Displacement

OD (ppf) ID (bbl/ft) (bbl/ft)
(In.) 40.5 (In.)
10.050 0.0981 0.0147
45.5 9.950 0.0962 0.0166
51.0 9.850 0.0943 0.0186
55.5 9.760 0.0925 0.0202
10 ¾ 60.7 9.660 0.0907 0.0216
65.7 9.560 0.0888 0.0235
71.1 9.450 0.0868 0.0255
76.0 9.350 0.0849 0.0273
81.0 9.250 0.0831 0.0291
47.0 11.000 0.1175 0.0171
11 ¾ 54.0 10.880 0.1150 0.0197
60.0 10.772 0.1127 0.0218
48.0 12.715 0.1571 0.0175
54.5 12.615 0.1546 0.0198
61.0 12.515 0.1522 0.0219
13 ⅜ 68.0 12.415 0.1497 0.0247
72.0 12.347 0.1481 0.0262
77.0 12.275 0.1464 0.0274
85.0 12.159 0.1436 0.0302
65.0 15.250 0.2259 0.0237
75.0 15.124 0.2222 0.0273
16 84.0 15.100 0.2189 0.0306
109.0 14.688 0.2096 0.0391
118.0 14.570 0.2062 0.0425
87.5 17.755 0.3062 0.0307
18 ⅝ 109.0 17.491 0.2972 0.0398
122.0 17.385 0.2936 0.0434
94.0 19.124 0.3553 0.0342
20 106.5 19.000 0.3507 0.0388
133.0 18.730 0.3408 0.0484
24 x 5/8" 156.0 22.750 0.5028 0.0568
t30
in
x 1" 310.0 28.000 0.7616 0.1127
t36in
x 1" 374.0 34.000 1.1230 0.1360
t48
in
x 1" 502.0 46.000 2.0556 0.1826
tin
Note: To find casing weight for other wall thicknesses:
Weight of Casinglb/ft = 10.68 x (Odin – tin) x tin
Where:
tin = Wall thickness (inches)
 Hole Capacity
47
Hole Hole
Hole Diameter (In.) Diamet
Hole Capaci
Capacity (bbl/ft)
er (In.) ty
(bbl/ft)
23 0.5139
3 0.0087
23 ½ 0.5365
3½ 0.0119
24 0.5595
4 0.0155
24 ½ 0.5831
4½ 0.0197
25 0.6071
5 0.0243
25 ½ 0.6317
5½ 0.0294
26 0.6567
6 0.0350
26 ½ 0.6822
6½ 0.0410
27 0.7082
7 0.0476
27 ½ 0.7347
7½ 0.0546
28 0.7616
8 0.0622
28 ½ 0.7891
8½ 0.0702
29 0.8170
9 0.0787
29 ½ 0.8454
9½ 0.0877
30 0.8743
10 0.0971
30 ½ 0.9037
10 ½ 0.1071
31 0.9336
11 0.1175
31 ½ 0.9639
11 ½ 0.1285
32 0.9948
12 0.1399
32 ½ 1.0261
12 ½ 0.1518
33 1.0579
13 0.1642
33 ½ 1.0902
13 ½ 0.1770
34 1.1230
14 0.1904
34 ½ 1.1563
14 ½ 0.2042
35 1.1900
15 0.2086
35 ½ 1.2243
15 ½ 0.2334
36 1.2590
16 0.2487
36 ½ 1.2942
16 ½ 0.2645
37 1.3299
17 0.2807
37 ½ 1.3661
17 ½ 0.2975
38 1.4028
18 0.3147
38 ½ 1.4399
18 ½ 0.3325
39 1.4776
19 0.3507
39 ½ 1.5157
19 ½ 0.3694
40 1.5543
20 0.3886
40 ½ 1.5934
20 ½ 0.4082
41 1.6330
21 0.4284
41 ½ 1.6731
21 ½ 0.4490
42 1.7136
22 0.4702
42 ½ 1.7547
22 ½ 0.4918
 Liner
STROKE LENGTH (INCHES) Units
Diameter 2 2½ 3 4 5 6 7 7½ 8 8½ 9 9½ 10 11 12
0.0005 0.0006 0.0007 0.0010 0.0012 0.0015 0.0017 0.0018 0.0019 0.0021 0.0022 0.0023 0.0024 0.0027
1"
0.0029 BBLS/STK
0.0204 0.0255 0.0306 0.0408 0.0510 0.0612 0.0714 0.0765 0.0816 0.0868 0.0919 0.0970 0.1021 0.1123
0.1225 Gal/STK
1 ⅜" 0.000 0.001 0.001 0.001 0.002 0.002 0.003 0.003 0.003 0.003 0.004 0.004 0.004 0.005 0.0055
9 1 4 8 3 8 2 4 7 9 1 4 6 1 BBLS/STK
0.0386 0.0482 0.0579 0.0772 0.0965 0.1158 0.1351 0.1447 0.1544 0.1640 0.1737 0.1833 0.1930 0.2123
0.2315 Gal/STK
1 ½" 0.0011 0.0014 0.0016 0.0022 0.0027 0.0033 0.0038 0.0041 0.0044 0.0046 0.0049 0.0052 0.0055 0.0060
0.0066 BBLS/STK
0.0459 0.057 0.068 0.091 0.114 0.137 0.160 0.172 0.183 0.195 0.206 0.218 0.229 0.252 0.2756 Gal/STK
4 9 9 8 8 7 2 7 2 7 2 6 6
1 ⅝" 0.0013 0.0016 0.0019 0.0026 0.0032 0.0039 0.0045 0.0048 0.0051 0.0055 0.0058 0.0061 0.0064 0.0071
0.0077 BBLS/STK
0.0539 0.0674 0.0809 0.1078 0.1348 0.1617 0.1887 0.2021 0.2156 0.2291 0.2426 0.2560 0.2695 0.2965
0.3234 Gal/STK
1 ¾" 0.001 0.001 0.002 0.003 0.003 0.004 0.005 0.005 0.006 0.006 0.006 0.007 0.007 0.008 0.0089
5 9 2 0 7 5 2 6 0 3 7 1 4 2 BBLS/STK
0.0625 0.0781 0.0938 0.1250 0.1563 0.1875 0.2188 0.2344 0.2500 0.2657 0.2813 0.2969 0.3126 0.3438
0.3751 Gal/STK
0.0019 0.0024 0.0029 0.0039 0.0049 0.0058 0.0068 0.0073 0.0078 0.0083 0.0087 0.0092 0.0097 0.0107
2"
0.0117 BBLS/STK
0.0816 0.102 0.122 0.163 0.204 0.244 0.285 0.306 0.326 0.347 0.367 0.387 0.408 0.449 0.4899 Gal/STK
1 5 3 1 9 8 2 6 0 4 8 2 1
2 ¼" 0.0025 0.0031 0.0037 0.0049 0.0062 0.0086 0.0092 0.0098 0.0105 0.0111 0.0117 0.0123 0.0135 0.0148
0.0074 BBLS/STK
0.1033 0.1292 0.1550 0.2067 0.2583 0.3617 0.3875 0.4133 0.4392 0.4650 0.4908 0.5167 0.5683 0.6200
0.3100 Gal/STK
2 ½" 0.003 0.003 0.004 0.006 0.007 0.009 0.010 0.011 0.012 0.012 0.013 0.014 0.015 0.016 0.0182
0 8 6 1 6 1 6 4 2 9 7 4 2 7 BBLS/STK

4
0.1276 0.1595 0.1914 0.2552 0.3189 0.4465 0.4784 0.5103 0.5422 0.5741 0.6060 0.6379 0.7017 0.7655
0.3827 Gal/STK
2 ¾" 0.0037 0.0046 0.0055 0.0074 0.0092 0.0129 0.0138 0.0147 0.0156 0.0165 0.0175 0.0184 0.0202 0.0221

Triplex Pumps 100%

0.0110 BBLS/STK
0.1544 0.193 0.231 0.308 0.385 0.463 0.540 0.578 0.617 0.656 0.694 0.733 0.771 0.849 0.9262 Gal/STK
0 5 7 9 1 3 9 5 1 6 2 8 0
0.0044 0.0055 0.0066 0.0087 0.0109 0.0153 0.0164 0.0175 0.0186 0.0197 0.0208 0.0219 0.0241 0.0262
0.0131 BBLS/STK
3"
0.1837 0.2296 0.2756 0.3674 0.4593 0.6430 0.6889 0.7348 0.7808 0.8267 0.8726 0.9185 1.0104 1.1022
0.5511 Gal/STK

3 ¼" 0.005 0.006 0.007 0.010 0.012 0.015 0.018 0.019 0.020 0.021 0.023 0.024 0.025 0.028 0.0308
1 4 7 3 8 4 0 3 5 8 1 4 7 2 BBLS/STK
0.2156 0.2695 0.3234 0.4312 0.5390 0.7546 0.8085 0.8624 0.9163 0.9702 1.0241 1.0780 1.1858 1.2936
0.6468 Gal/STK
3 ½" 0.0060 0.0074 0.0089 0.0119 0.0149 0.0208 0.0223 0.0238 0.0253 0.0268 0.0283 0.0298 0.0327 0.0357
0.0179 BBLS/STK
0.2500 0.312 0.375 0.500 0.625 0.750 0.875 0.937 1.000 1.062 1.125 1.187 1.250 1.375 1.5003 Gal/STK
6 1 1 1 1 2 7 2 7 2 7 2 3
3 ¾" 0.0068 0.0085 0.0103 0.0137 0.0171 0.0239 0.0256 0.0273 0.0290 0.0308 0.0325 0.0342 0.0376 0.0410
0.0205 BBLS/STK
0.2870 0.3588 0.4306 0.5741 0.7176 1.0047 1.0764 1.1482 1.2199 1.2917 1.3635 1.4352 1.5787 1.7223
0.8611 Gal/STK
 Liner
STROKE LENGTH (INCHES) Units
Diameter 2 2½ 3 4 5 6 7 7½ 8 8½ 9 9½ 10 11 12
4" 0.0078 0.0097 0.0117 0.0156 0.0194 0.0233 0.0272 0.0292 0.0311 0.0330 0.0350 0.0369 0.0389 0.0428
0.0467 BBLS/STK
0.3266 0.4082 0.4899 0.6532 0.8165 0.9798 1.1431 1.2247 1.3064 1.3880 1.4697 1.5513 1.6330 1.7963
1.9596 Gal/STK
4 0.008 0.011 0.013 0.017 0.021 0.026 0.030 0.032 0.035 0.037 0.039 0.041 0.043 0.048 0.0527
¼" 8 0 2 6 9 3 7 9 1 3 5 7 9 3 BBLS/STK
0.3687 0.4609 0.5530 0.7374 0.9217 1.1061 1.2907 1.3826 1.4748 1.5669 1.6591 1.7513 1.8435 2.0278
2.2122 Gal/STK
4 0.0098 0.0123 0.0148 0.0197 0.0246 0.0295 0.0344 0.0369 0.0394 0.0418 0.0443 0.0467 0.0492 0.0541
½"
0.0590 BBLS/STK
0.4133 0.516 0.620 0.826 1.033 1.240 1.446 1.550 1.653 1.756 1.860 1.963 2.066 2.273 2.4801 Gal/STK
7 0 7 4 0 7 0 4 7 0 4 7 4
4 0.0110 0.0137 0.0164 0.0219 0.0274 0.0329 0.0384 0.0411 0.0439 0.0466 0.0493 0.0521 0.0548 0.0603
¾" 0.0658 BBLS/STK
0.4605 0.5757 0.6908 0.9211 1.1514 1.3816 1.6119 1.7270 1.8422 1.9573 2.0725 2.1876 2.3027 2.5330
2.7633 Gal/STK
0.015 0.018 0.024 0.030 0.036 0.042 0.045 0.048 0.051 0.054 0.057 0.060 0.066 0.0729
5" 2 2 3 4 5 5 6 6 6 7 7 8 8 BBLS/STK
0.0122
0.5103 0.6379 0.7655 1.0206 1.2758 1.5309 1.7861 1.9136 2.0412 2.1688 2.2964 2.4239 2.5515 2.8067
3.0618 Gal/STK
5 0.0134 0.0167 0.0201 0.0268 0.0335 0.0402 0.0469 0.0502 0.0536 0.0569 0.0603 0.0636 0.0670 0.0737
¼"
0.0804 BBLS/STK
0.5626 0.703 0.843 1.125 1.406 1.687 1.969 2.109 2.250 2.391 2.531 2.672 2.813 3.094 3.3756 Gal/STK
3 9 2 5 8 1 8 4 1 7 4 0 3
5 0.0147 0.0184 0.0221 0.0294 0.0368 0.0515 0.0551 0.0588 0.0625 0.0662 0.0698 0.0735 0.0809 0.0882
½" 0.0441 BBLS/STK
0.6175 0.7718 0.9262 1.2349 1.5437 2.1611 2.3155 2.4699 2.6242 2.7786 2.9329 3.0873 3.3960 3.7048
1.8524 Gal/STK
5 0.016 0.020 0.024 0.032 0.040 0.048 0.056 0.060 0.064 0.068 0.072 0.076 0.080 0.088 0.0964
¾" 1 1 1 1 2 2 2 3 3 3 3 3 3 4 BBLS/STK
0.6749 0.8436 1.0123 1.3497 1.6872 2.3621 2.5308 2.6995 2.8682 3.0369 3.2056 3.3744 3.7118 4.0492
2.0246 Gal/STK
0.0175 0.0219 0.0262 0.0350 0.0437 0.0612 0.0656 0.0700 0.0744 0.0787 0.0831 0.0875 0.0962 0.1050

Triplex Pumps 100%

6"
0.0525 BBLS/STK
0.7348 0.918 1.102 1.469 1.837 2.204 2.571 2.755 2.939 3.123 3.306 3.490 3.674 4.041 4.4090 Gal/STK
5 2 7 2 5 9 6 3 0 7 5 2 6
6 0.0190 0.0237 0.0285 0.0380 0.0475 0.0664 0.0712 0.0759 0.0807 0.0854 0.0902 0.0949 0.1044 0.1139
¼" 0.0570 BBLS/STK
0.7973 0.9967 1.1960 1.5947 1.9934 2.7907 2.9900 3.1894 3.3887 3.5880 3.7874 3.9867 4.3854 4.7841
2.3920 Gal/STK
6 0.020 0.025 0.030 0.041 0.051 0.061 0.071 0.077 0.082 0.087 0.092 0.097 0.102 0.112 0.1232
½" 5 7 8 1 3 6 9 0 1 3 4 5 7 9 BBLS/STK
0.8624 1.0780 1.2936 1.7248 2.1560 3.0184 3.2340 3.4496 3.6652 3.8808 4.0964 4.3120 4.7432 5.1744
2.5872 Gal/STK
6 0.0221 0.0277 0.0332 0.0443 0.0554 0.0775 0.0830 0.0886 0.0941 0.0996 0.1052 0.1107 0.1218 0.1329
¾"
0.0664 BBLS/STK
0.9300 1.162 1.395 1.860 2.325 2.790 3.255 3.487 3.720 3.952 4.185 4.417 4.650 5.115 5.5801 Gal/STK
5 0 0 1 1 1 6 1 6 1 6 1 1
0.0238 0.0298 0.0357 0.0476 0.0595 0.0833 0.0893 0.0953 0.1012 0.1072 0.1131 0.1191 0.1310 0.1429
7" 0.0714 BBLS/STK
1.0002 1.2502 1.5003 2.0004 2.5005 3.5007 3.7507 4.008 4.2508 4.5008 4.7509 5.0009 5.5010 6.0011
3.0006 Gal/STK
 5
Initia
Mud W DESIRED MUD WEIGHT
l t (PPG)
9.5 10.0 10.5 11.0 11.5 12.0 12.5 13.0 13.5 14.0 14.5 15.0 15.5 16.0 16.5 17.0 17.5 18.0
(ppg
9.0 29 59 90 123 156 192 229 268 308 350 395 442 490 542 596 653 714 778
29 60 92 125 160 196 234 273 315 359 405 452 503 557 612 672 735

Mud Weight
9.5
10.0 43 30 61 93 128 164 201 239 280 323 368 414 464 516 571 630 691
10.5 85 30 31 62 96 131 167 205 245 287 331 376 426 479 531 588 648
11.0 128 60 23 31 64 98 134 171 210 251 294 339 387 437 490 546 605
11.5 171 90 46 19 32 66 101 137 175 215 258 301 348 397 449 504 562
12.0 214 120 69 37 16 33 67 103 140 179 221 263 310 357 408 462 518
12.5 256 150 92 56 32 14 34 68 105 144 184 226 271 318 367 420 475
13.0 299 180 115 75 48 27 12 34 70 108 147 188 232 278 327 378 432
13.5 342 210 138 94 63 41 24 11 35 72 111 150 194 238 286 336 389
14.0 385 240 161 112 76 54 36 21 10 36 74 113 155 199 245 294 345
14.5 427 270 185 131 95 68 48 32 19 9 37 75 116 159 204 252 302
15.0 470 300 208 150 110 82 60 43 29 18 8 37 77 119 163 210 259
15.5 513 330 231 169 126 95 72 54 39 26 16 8 39 79 122 168 216
16.0 556 360 254 187 142 109 84 64 48 35 24 15 7 40 81 126 172
16.5 598 390 277 206 158 123 96 75 58 44 32 23 14 7 41 84 129
17.0 641 420 300 225 174 136 108 86 68 53 40 30 21 13 6 42 86
17.5 684 450 323 244 189 150 120 96 77 62 49 38 28 20 12 6 43
18.0 726 480 346 262 205 163 132 107 87 71 57 45 35 26 18 12 5
Dilution or Cut Back: The gray section of the chart shows the number of barrels Mud Weight Increase: The yellow section of the chart indicates the
water which must be added to 100 bbls of mud to produce the desired weight number
reduction. of 100 lb sacks of barite which must be added to 100 bbls of mud to
 Mud Weights
51
Gradient Gradient
3 3 Specific
lb/gal lb/ft kg/m Depth Depth
Gravity
(psi/ft) (kPa/m)
8.34 62.38 999.3 1.00 0.434 9.8
8.5 63.58 1018.5 1.02 0.442 10.0
8.6 64.32 1030.5 1.03 0.447 10.1
8.7 65.07 1042.4 1.04 0.452 10.2
8.8 65.82 1054.4 1.05 0.458 10.4
8.9 66.57 1066.4 1.07 0.463 10.5
9.0 67.31 1078.4 1.08 0.468 10.6
9.1 68.06 1090.4 1.09 0.473 10.7
9.2 68.81 1102.3 1.10 0.478 10.8
9.3 69.56 1114.3 1.12 0.484 10.9
9.4 70.31 1126.3 1.13 0.489 11.1
9.5 71.05 1138.3 1.14 0.494 11.2
9.6 71.80 1150.3 1.15 0.499 11.3
9.7 72.55 1162.3 1.16 0.504 11.4
9.8 73.30 1174.2 1.18 0.510 11.5
9.9 74.05 1186.2 1.19 0.515 11.6
10.0 74.79 1198.2 1.20 0.520 11.8
10.1 75.54 1210.2 1.21 0.525 11.9
10.2 76.29 1222.2 1.22 0.530 12.0
10.3 77.04 1234.2 1.24 0.536 12.1
10.4 77.79 1246.1 1.25 0.541 12.2
10.5 78.53 1258.1 1.26 0.546 12.4
10.6 79.28 1270.1 1.27 0.551 12.5
10.7 80.03 1282.1 1.28 0.556 12.6
10.8 80.78 1294.1 1.29 0.562 12.7
10.9 81.53 1306.0 1.31 0.567 12.8
11.0 82.27 1318.0 1.32 0.572 12.9
11.1 83.02 1330.0 1.33 0.577 13.1
11.2 83.77 1342.0 1.34 0.582 13.2
11.3 84.52 1354.0 1.36 0.588 13.3
11.4 85.27 1366.0 1.37 0.593 13.4
11.5 86.01 1377.9 1.38 0.598 13.5
11.6 86.76 1389.9 1.39 0.603 13.6
11.7 87.51 1401.9 1.40 0.608 13.8
11.8 88.26 1413.9 1.41 0.614 13.9
11.9 89.01 1425.9 1.43 0.619 14.0
12.0 89.75 1437.8 1.44 0.624 14.1
12.1 90.50 1449.8 1.45 0.629 14.2
12.2 91.25 1461.8 1.46 0.634 14.4
12.3 92.00 1473.8 1.48 0.640 14.5
12.4 92.74 1485.8 1.49 0.645 14.6
12.5 93.49 1497.8 1.50 0.650 14.7
12.6 94.24 1509.7 1.51 0.655 14.8
12.7 94.99 1521.7 1.52 0.660 14.9
12.8 95.74 1533.7 1.53 0.666 15.1
12.9 96.48 1545.7 1.55 0.671 15.2
13.0 97.23 1557.7 1.56 0.676 15.3
13.1 97.98 1569.6 1.57 0.681 15.4
13.2 98.73 1581.6 1.58 0.686 15.5
52 Mud Weights
Gradient Gradient
3 3 Specific
lb/gal lb/ft kg/m Depth Depth
Gravity
(psi/ft) (kPa/m)
13.3 99.48 1593.6 1.60 0.692 15.6
13.4 100.2 1605.6 1.61 0.697 15.8
13.5 2
100.9 1617.6 1.62 0.702 15.9
13.6 7
101.7 1629.6 1.63 0.707 16.0
13.7 2
102.4 1641.5 1.64 0.712 16.1
13.8 7
103.2 1653.5 1.65 0.718 16.2
13.9 2
103.9 1665.5 1.67 0.723 16.4
14.0 6
104.7 1677.5 1.68 0.728 16.5
14.1 1
105.4 1689.5 1.69 0.733 16.6
14.2 6
106.2 1701.5 1.70 0.738 16.7
14.3 1
106.9 1713.4 1.72 0.744 16.8
14.4 6
107.7 1725.4 1.73 0.749 16.9
14.5 0
108.4 1737.4 1.74 0.754 17.1
14.6 5
109.2 1749.4 1.75 0.759 17.2
14.7 0
109.9 1761.4 1.76 0.764 17.3
14.8 5
110.7 1773.3 1.78 0.770 17.4
14.9 0
111.4 1785.3 1.79 0.775 17.5
15.0 4
112.1 1797.3 1.80 0.780 17.6
15.1 9
112.9 1809.3 1.81 0.785 17.8
15.2 4
113.6 1821.3 1.82 0.790 17.9
15.3 9
114.4 1833.3 1.84 0.796 18.0
15.4 4
115.1 1845.2 1.85 0.801 18.1
15.5 8
115.9 1857.2 1.86 0.806 18.2
15.6 3
116.6 1869.2 1.87 0.811 18.3
15.7 8
117.4 1881.2 1.88 0.816 18.5
15.8 3
118.1 1893.2 1.90 0.822 18.6
15.9 8
118.9 1905.1 1.91 0.827 18.7
16.0 2
119.6 1917.1 1.92 0.832 18.8
16.1 7
120.4 1929.1 1.93 0.837 18.9
16.2 2
121.1 1941.1 1.94 0.842 19.1
16.3 7
121.9 1953.1 1.96 0.846 19.2
16.4 1
122.6 1965.1 1.97 0.853 19.3
16.5 6
123.4 1977.0 1.98 0.858 19.4
16.6 1
124.1 1989.0 2.00 0.863 19.5
16.7 6
124.9 2001.0 2.01 0.868 19.6
16.8 1
125.6 2013.0 2.02 0.874 19.8
16.9 5
126.4 2025.0 2.03 0.879 19.9
17.0 0
127.1 2036.9 2.04 0.884 20.0
17.1 5
127.9 2048.9 2.05 0.889 20.1
17.2 0
128.6 2060.9 2.06 0.894 20.2
17.3 5
129.3 2072.9 2.08 0.900 20.3
17.4 9
130.1 2084.9 2.09 0.905 20.5
17.5 4
130.8 2096.9 2.10 0.910 20.6
17.6 9
131.6 2108.8 2.11 0.915 20.7
17.7 4
132.3 2120.8 2.12 0.920 20.8
17.8 9
133.1 2132.8 2.14 0.926 20.9
17.9 3
133.8 2144.8 2.15 0.931 21.1
18.0 8
134.6 2156.8 2.16 0.936 21.2
18.1 3
135.3 2168.8 2.17 0.941 21.3
8
 Mud Weights
53
Gradient Gradient
3 3 Specific
lb/gal lb/ft kg/m Depth Depth
Gravity
(psi/ft) (kPa/m)
18.2 136.1 2180.7 2.18 0.946 21.4
18.3 3
136.8 2192.7 2.20 0.952 21.5
18.4 7
137.6 2204.7 2.21 0.957 21.6
18.5 2
138.3 2216.7 2.22 0.962 21.8
18.6 7
139.1 2228.7 2.23 0.967 21.9
18.7 2
139.8 2240.6 2.24 0.972 22.0
18.8 7
140.6 2252.6 2.26 0.978 22.1
18.9 1
141.3 2264.6 2.27 0.983 22.2
19.0 6
142.1 2276.6 2.28 0.988 22.3
19.1 1
142.8 2288.6 2.29 0.993 22.5
19.2 6
143.6 2300.6 2.30 0.998 22.6
19.3 1
144.3 2312.5 2.32 1.004 22.7
19.4 5
145.1 2324.5 2.33 1.009 22.8
19.5 0
145.8 2336.5 2.34 1.014 22.9
19.6 5
146.6 2348.5 2.35 1.019 23.1
19.7 0
147.3 2360.5 2.36 1.024 23.2
19.8 4
148.0 2372.4 2.38 1.030 23.3
19.9 9
148.8 2384.4 2.39 1.035 23.4
20.0 4
149.5 2396.4 2.40 1.040 23.5
9

Specifications for BOP Flanges,

Ring
Gaskets, and Flange Bolts &
Nuts
Stack Approved Bolt Nut
Approved Flanges
Rating Ring Gaskets Spec. Spec.
2000 API type 6B with ASTM ASTM
psi and type R flat API Type RX Grade Grade
3000 psi Bottom Groove B-7 2-H
API Type 6B
with Type R API Type RX
Flat Bottom or ASTM ASTM
5000 psi groove or API Type BX Grade Grade
API Type 6BX with with Type B-7 2-H
Type BX Groove 6BX Flange

ASTM ASTM
10,00 API Type 6BX with
API Type BX Grade Grade
0 psi Type BX Groove B-7 2-H

NOTE: Acceptable flange ring

Bolt Torqu gasket material for sweet oil
Size e applications is low-carbon steel
¾ -(In.
10 (Ft-
200 and for sour oil or gas is type 316
UNC
⅞ - 9 UNC 325 stainless or type 304 stainless
steel. ASTM A-
1 - 8 UNC 475
193 Grade B/M with a maximum
1⅛-8 600 Rockwell Hardness of 22 may be
UN
1 ½-8 1400 acceptable but should be derated
UN
1⅝-8 1700 as per Table 1.4B of API Spec 6A.
UN Specifications as per API Spec 6A
1 ¾-8 2040 "Wellhead Equipment".
UN
1⅞-8 3220
54 Gate Valve Data

Size
Size, Worki
Working
ng Pre
Pressure and
Numbe
Number of Turns to Oper
perate
Camero W-K-
Cameron valvesn have a W-K-M valves M have a
round handwheel with the unique wedge shaped
name “Cameron” embossed handwheel. Operate W-K-
on it. Operate Cameron M valves full open or full
Valves full open or full close, close, then jam tight.
then back off
¼ turn.
3,000/5,000 psi WP 3,000/5,000 psi WP
Model Inches Turns Model Inches Turns
2 1/16 12 1/2 2 1/16 13
2 9/16 15 1/4 2 9/16 16
F, FC & M
3 1/8 18 1/4 3 1/8 20
4 1/16 23 1/2 4 1/16 25
10,000 psi WP 10,000 - 15,000 psi WP
1 13/16 12 1
/2 1 13/16 14
2 1/16 12 1
/2 2 1/16 12
FC, FL M-1
2 9/16 15 1
/4 2 9/16 15
& &
FLS 3 1/16 18 1
/4 M-2 3 1/16 17 1/2
4 1/16 23 1
/2 4 1/16 23
15,000 – 20,000 psi WP 20,000 psi WP
1 13/16 12 1
/2 1 13/16 15
2 1/16 12 1
/2 2 1/16 16 1/2
FLS 2 9/16 15 3
/4 M-3 2 9/16 19 1/2
3 1/16 22 7
/8 3 1/16 23
4 1/16 29 1
/2 4 1/16 29
15,000 – 20,000 psi WP
1 13/16 12 1
/2
2 1/16 12 1
/2
F, FC & 2 9/16 15 3
/4
FL 3 1/16 15 1
/4
4 1/16 29 1
/2
10,000 psi WP
1 13/16 12
2 1/16 12
J & JS 2 9/16 17 1/4
3 1/16 21 1/2
4 1/16 23
15,000 psi WP
1 13/16 15 3/4
2 1/16 15 3/4
J &JS 16 /2
2 9/ 19 1
Torque
3 1/16 135Multiplie
r
20,000 psi WP
1 13/16 15 3/4
2 1/16 15 3/4
J & JS Torque
2 9/16 117Multiplie
r Torque
3 1/16 135Multiplie
 Gate Valve Data
55

Size
Size, Worki
Working
ng Pre
Pressure and
Numbe
Number of Turns to Oper
perate
Ingram Cactus McEvoy
Ingram Cactus valves have a McEvoy valves have a round
round handwheel with three handwheel with the name
spokes and the name “McEvoy” embossed on it.
“Ingram Cactus” embossed Operate McEvoy valves full
on it. Operate Ingram open or full close, then back
Cactus valves Model 205 off ¼ turn.
and 215 full open or full
close, then jam tight.
Operate Model 405 and 315
full open or full close, then
back off ¼ turn.
2,000/5,000 psi WP 2,000/3,000/5,000 psi WP
Model Inches Turns Model Inches Turns
2 1/16 13 2 1/16 13
2 9/16 16 2 9/16 16
205 C
3 1/8 20 3 1/8 18
4 1/16 25 4 1/16 17
2,000/5,000 psi WP 10,000 psi WP
2 1/16 16 1 13/16 11
2 9/16 19 2 1/16 13
405 3 1/8 23 E 2 9/16 10 1/2
4 1/16 24 1/2 3 1/16 12 1/2
4 1/16 17
10,000 – 15,000 psi WP 15,000 psi WP
1 13/16 14 1 13/16 11
2 1/16 12 2 1/16 9
215 2 9/16 15 E 2 9/16 10 1/2
3 1/16 17 1/2 3 1/16 26
4 1/16 23 4 1/16 ---
10,000 – 15,000 psi WP 10,000 psi WP
1 13/16 16 1 13/16 11
2 1/16 18 2 1/16 9
315 2 9/16 17 E-2 2 9/16 10 1/2
3 1/16 24 3 1/16 12 3/4
4 1/16 21 4 1/16 17 1/8
15,000 psi WP
1 13/16 7 3/4
2 1/16 9
E-2 2 9/16 10 1/2
3 1/16 12 3/4
4 1/16 17 1/8
Nominal Standard

5
Service Energized Old API Through Numbe Bolt Size Bolt Flange Flange
Flange Rating Ring Ring Series Bore ID (In.) r of (In.) Circle Diameter Thickness
Size (In.) (psi) Gasket Number Designation (In.) (In.) (In.)
Number 13
10M BX151 1 /16 8 ¾ 5¾ 7⅜ 1 21/32
1 13
/16 15M BX151 1 13
/16 8 ⅞ 6 5/16 8 3/16 1 25/32
13
20M 1 /16 8 1 8 10 ⅛ 2½

API Ring Joint

2M R23 RX23 2" 600 2 1/16 8 ⅝ 5 6½ 1 5/16
5M R24 RX24 2" 1,500 2 1/16 8 ⅞ 6½ 8½ 1 13/16
1
2 /16 10M BX152 2 1/16 8 ¾ 6¼ 7⅞ 1 47/64
15M BX152 2 1/16 8 ⅞ 6⅞ 8¾ 2
20M BX152 2 1/16 8 1⅛ 9 1/16 11 5/16 2 13/16
2M R26 RX26 2 ½" 600 2 9/16 8 ¾ 5⅞ 7½ 1 7/16
5M R27 RX27 2 ½" 1,500 2 9/16 8 1 7½ 9⅝ 1 15/16
2 9/16 10M BX153 2 9/16 8 7
/8 7¼ 9⅛ 2 1/64
15M BX153 2 9/16 8 1 7⅞ 10 2¼
20M BX153 2 9/16 8 1¼ 10 5/16 12 13/16 3⅛
10M BX154 3 1/16 8 1 8½ 10 ⅝ 2 19/64
3 1/16 15M BX154 3 1/16 8 1⅛ 9 1/16 11 5/16 2 17/32
20M BX154 3 1/16 8 1⅜ 11 5/16 14 1/16 3⅜
2M R31 RX31 3" 600 3⅛ 8 ¾ 6⅝ 8¼ 1 9/16
3⅛ 3M R31 RX31 3" 900 3⅛ 8 ⅞ 7½ 9½ 1 13/16
5M R35 RX35 3" 1,500 3⅛ 8 1⅛ 8 10 ½ 2 3/16
Nominal Standard
Flange Service Ring Energized Old API Through Number Bolt Size Bolt Circle Flange Flange
Rating (psi) Ring Series Bore ID (In.) of Bolts (In.) (In.) Diameter (In.) Thickness
Size (In.) Gasket (In.)
2M Number
R37 RX37 4" 600 4 1/16 8 ⅞ 8½ 10 ¾ 1 13/16
3M R37 RX37 4" 900 4 1/16 8 1⅛ 9¼ 11 ½ 2 1/16
5M R39 RX39 4" 1,500 4 1/16 8 1¼ 9½ 12 ¼ 2 7/16
4 1/16

API Ring Joint

10M BX155 4 1/16 8 1⅛ 10 3/16 12 7/16 2 49/64
15M BX155 4 1/16 8 1⅜ 11 7/16 14 3/16 3 3/32
20M BX155 4 1/16 8 1¾ 14 1/16 17 9/16 4 3/16
2M R41 RX41 5⅛ 8 1 10 ½ 13 2 1/16
3M R41 RX41 5⅛ 8 1¼ 11 13 ¾ 2 5/16
5⅛
5M R44 RX44 5⅛ 8 1½ 11 ½ 14 ¾ 3 3/16
10M BX169 5⅛ 12 1⅛ 11 13/16 14 1/16 3⅛
2M R45 RX45 6" 600 7 1/16 12 1 11 ½ 14 2 3/16
3M R45 RX45 6" 900 7 1/16 12 1⅛ 12 ½ 15 2½
5M R46 RX46 6" 1,500 7 1/16 12 1⅜ 12 ½ 15 ½ 3⅝
7 1/16
10M BX156 7 1/16 12 1½ 15 ⅞ 18 ⅞ 4 1/16
15M BX156 7 1/16 16 1½ 16 ⅞ 19 ⅞ 4 11/16
20M BX156 7 1/16 16 2 21 13/16 25 13/16 6½
2M R49 RX49 8" 600 9 12 1⅛ 13 ¾ 16 ½ 2½
3M R49 RX49 8" 900 9 12 1⅜ 15 ½ 18 ½ 2 13/16
9 5M R50 RX50 8" 1,500 9 12 1⅝ 15 ½ 19 4 1/16
10M BX157 9 16 1½ 18 ¾ 21 ¾ 4⅞
15M BX157 9 16 1⅞ 21 ¾ 25 ½ 5¾

5
Nominal Service Standard Energized Old API Through Bolt Size Bolt Flange Flange
Numbe
Flange Ring

5
Rating Ring Series Bore ID (In.) r of (In.) Circle Diameter Thickness
Size (In.) (psi) Gasket Number Designation (In.) (In.) (In.)
2M Number RX53 10" 600 11 16 1¼ 17 20 2 13/16
3M R53
R53 RX53 10" 900 11 16 1⅜ 18 ½ 21 ½ 3 1/16
R54 RX54 10" 1,500 11 12 1⅞ 19 23 4 11/16

API Ring Joint

10M BX158 11 16 1¾ 22 ¼ 25 ¾ 5 9/16
15M BX158 11 20 2 28 32 7⅜
2M R57 RX57 12" 600 13 ⅝ 20 1¼ 19 ¼ 22 2 15/16
3M R57 RX57 12" 900 13 ⅝ 20 1⅜ 21 24 3 7/16
13 ⅝ 5M BX160 13 ⅝ 16 1⅝ 23 ¼ 26 ½ 4 7/16
10M BX159 13 ⅝ 20 1⅞ 26 ½ 30 ¼ 6⅝
15M BX159 13 ⅝ 20 2¼ 30 ⅜ 34 ⅞ 7⅞
2M R65 RX65 16" 600 16 ¾ 20 1½ 23 ¾ 27 3 5/16
3M R66 RX66 16" 900 16 ¾ 20 1⅝ 24 ¼ 27 ¾ 3 15/16
16 ¾
5M BX162 16 ¾ 16 1⅞ 26 ⅝ 30 ⅜ 5⅛
10M BX162 16 ¾ 24 1⅞ 30 9/16 34 5/16 6⅝
5M BX163 18 ¾ 20 2 31 ⅝ 35 ⅝ 6 17/32
18 ¾
10M BX164 18 ¾ 24 2¼ 36 7/16 40 15/16 8 25/32
20 ¾ 3M R74 RX74 20" 900 20 ¾ 20 2 29 ½ 33 ¾ 4¾
21 ¼ 2M R73 RX73 20" 600 21 ¼ 24 1⅝ 28 ½ 32 3⅞
21 ¼ 5M BX165 21 ¼ 24 2 34 ⅞ 39 7⅛
21 ¼ 10M BX166 21 ¼ 24 2½ 40 ¼ 45 9½
2M BX167 26 ¾ 20 1¾ 37 ½ 41 4 31/32
26 ¾
3M BX168 26 ¾ 24 2 39 ⅜ 43 ⅜ 6 11/32
 BOP Fluid Operating Volumes 59

Cameron BOPs

Cameron Type 'D' Annular Preventer

BOP Nom. Size Working Fluid to Close Fluid to Open
(In.) Pressure (psi) (gal) (gal)
5,000 1.69 1.39
7 1/16
10,000 2.94 2.55
5,000 5.65 4.69
11
10,000 10.15 9.06
5,000 12.12 10.34
13 5/8
10,000 18.10 16.15

Cameron Type 'UM' Ram Preventer

BOP Nom. Size Working Fluid to Close Fluid to Open
(In.) Pressure (psi) (gal) (gal)
3,000 2.3 2.2
5,000 2.3 2.2
7 1/16
10,000 2.3 2.2
15,000 2.3 2.2
11 15,000 7.3 7.3
13 5/8 10,000 7.5 7.5

Cameron Type 'U' Ram Preventer

BOP Nom. Size
(Old API Working Fluid to Close Fluid to Open
Series Pressure (psi) (gal) (gal)
Designation)
3,000 1.3 1.3
7 1/16 (6)
5,000 1.3 1.3
10,000 1.3 1.3
7 1/16
15,000 1.3 1.3
3,000 3.5 3.4
11 (10)
5,000 3.5 3.4
10,000 3.5 3.4
11
15,000 5.8 5.7
13 5/8 (12) 3,000 5.8 5.5
5,000 5.8 5.5
13 5/8 10,000 5.8 5.5
15,000 10.6 10.4
3,000 10.6 9.8
16 3/4 5,000 10.6 9.8
10,000 12.5 11.6
18 3/4 10,000 23.1 21.3
20 3/4 (20) 3,000 8.7 8.1
2,000 8.7 9.0
21 1/4 5,000 30.0 27.3
10,000 26.9 24.5
26 3/4 3,000 10.8 10.1
60 Coiled Tubing Data

Cameron Type 'QRC' Ram Preventer

BOP Nom. Size
(Old API Working Fluid to Close Fluid to Open
Series Pressure (psi) (gal) (gal)
Designation)
3,000 0.81 0.95
7 1/16 (6)
5,000 0.81 0.95
3,000 2.36 2.70
9 (8)
5,000 2.36 2.70
3,000 2.77 3.18
11 (10)
5,000 2.77 3.18
13 5/8 (12) 3,000 4.42 5.10
16 3/4 (16) 2,000 6.00 7.05
17 3/4 (18) 2,000 6.00 7.05
Cameron Hydraulic Gate Valves
BOP Nom.
Size
Working Fluid to Fluid to
Type (psi) Open
(In.) Pressure Close
(gal)
HCR 4 0.52 0.61
HCR 43,000 5,000 0.52 0.61
HCR 6 3,000 1.95 2.25
HCR 6 5,000 1.95 2.25
F 4 3,000 0.30 0.30
F 4 5,000 0.30 0.30
F 4 10,000 0.59 0.59
F 6 3,000 0.84 0.84
F 6 5,000 0.84 0.84

Shaffe
ffer
BOPs
BOPs

Shaffer Spherical Annular Preventer

BOP Nom. Working Cover Fluid to Fluid to
Size (In.) Pressure (psi) Type Close (gal) Open (gal)
3,000 Bolted 4.57 3.21
7 1/16 5,000 Bolted 4.57 3.21
10,000 Bolted 17.11 13.95
3,000 Bolted 7.23 5.03
9
5,000 Bolted 11.05 8.72
3,000 Bolted 11.00 6.78
11 5,000 Bolted 18.67 14.59
10,000 Wedge 30.58 24.67
3,000 Bolted 23.50 14.67
13 5/8 5,000 Bolt/Wedge 23.58 17.41
10,000 Wedge 40.16 32.64
16 3/4 5,000 Wedge 33.26 25.61
18 3/4 5,000 Wedge 48.16 37.61
2,000 Bolted 32.59 16.92
21 1/4
5,000 Wedged 61.37 47.76
 BOP Fluid Operating Volumes 61

Shaffer Type 'LXT' Ram Preventer

BOP Nom. Working Fluid to Close Fluid to Open
Size (In.) Pressure (psi) (gal) (gal)
3,000 0.32 0.33
7
5,000 0.32 0.33
3,000 2.80 2.46
11
5,000 2.80 2.46

Shaffer Type 'NXT' Ram Preventer

BOP Nom. Working Fluid to Fluid to
Size (In.) Pressure (psi) Type Close (gal) Open (gal)
5,000 Poslock 14.04 12.74
Booster
5,000 (Poslock) 31.22 29.92
5,000 Manual-Lock 13.14 12.84
5,000 Ultralock IIB 16.74 15.44
10,000 Poslock 14.04 13.02
Booster
18 3/4 10,000 (Poslock) 31.22 29.92
10,000 Manual-Lock 13.14 13.14
10,000 Ultralock IIB 16.74 15.72
15,000 Poslock 14.04 13.02
Booster
15,000 (Poslock) 31.22 29.92
15,000 Manual-Lock 13.14 13.14
15,000 Ultralock IIB 16.74 15.72

Shaffer Type 'LWS' Ram Preventer

BOP Nom. Working Piston Size Fluid to
Fluid to
5,000 6 0.59 0.52
4 1/16
10,000 6 0.59 0.52
6½ 1.45 1.18
10,000 14 5.18 5.25
9 5,000 8½ 2.58 2.27
3,000 6½ 1.74 1.45
11 5,000 8½ 2.98 2.62
5,000 14 9.50 8.90
3,000 8½ 5.07 4.46
20 3/4 3,000 10 7.80 6.86
3,000 14 14.50 13.59
2,000 8½ 5.07 4.46
21 1/4 2,000 10 7.80 6.86
2,000 14 14.50 13.59
62 Coiled Tubing Data

Shaffer Type 'SL/SLX' Ram Preventer

BOP Nom. Working Piston Size Fluid to
Fluid to
10,000 10 2.72 2.34
10,000 14 6.00 5.57
7 1/
16
15,000 10 2.72 2.34
15,000 14 6.00 5.57
10,000 14 9.45 7.00
11
15,000 14 9.40 8.10
3,000 10 5.44 4.46
10 5.44 4.46
13 5/8 5,000 14 11.00 10.52
10,000 14 10.58 10.52
15,000 14 11.56 10.52
5,000 10 6.07 4.97
16 3/4 5,000 14 11.76 10.67
10,000 14 14.47 12.50
10,000 14 14.55 13.21
18 3/4
15,000 14 14.62 13.33
21 1/4 10,000 14 16.05 13.86
Shaffer Type 'DB' Hydraulic Gate Valves
BOP Nom. Working Pressure Fluid to Close Fluid to Open
Size (In.) (psi) (gal) (gal)
5,000 0.15 0.20
2 1/16 10,000 0.15 0.20
15,000 0.26 0.29
3 1/8 5,000 0.20 0.25
10,000 0.35 0.40
3 1/16
15,000 0.35 0.40
5,000 0.35 0.40
4 1/16 10000 0.45 0.50
15000 0.45 0.50
 BOP Fluid Operating Volumes 63

Hydril
BOPs
Hydril Type 'GK' Annular Preventer
BOP Nom. Working Pressure Fluid to Close Fluid to Open
Size (In.) (psi) (gal) (gal)
3,000 2.85 2.24
5,000 3.86 3.30
7 1/16 10,000 9.42 7.08
15,000 11.20 7.50
20,000 10.90 7.20
3,000 4.33 3.41
9 5,000 6.84 5.80
10,000 15.90 11.95
3,000 7.43 5.54
5,000 9.81 7.98
11
10,000 25.10 18.97
15,000 26.67 20.45
3,000 11.36 8.94
13 5/8 5,000 17.98 14.16
10,000 37.18 12.59
2,000 17.46 15.80
16 3/4 3,000 28.70 19.93
5,000 28.70 19.93

Hydril Type 'MSP' Annular Preventer

BOP Nom. Working Pressure Fluid to Close Fluid to Open
Size (In.) (psi) (gal) (gal)
1
7 /16 2,000 2.85 1.98
9 2,000 4.57 2.95
11 2,000 7.43 5.23
20 3/4 2,000 31.05 18.93
21 1/4 2,000 31.05 18.93
29 1/2 500 60.00 n/a
30 1,000 87.60 27.80

Hydril Type 'GX' Annular Preventer

BOP Nom. Working Pressure Fluid to Close Fluid to Open
Size (In.) (psi) (gal) (gal)
10,000 17.90 17.90
11
15,000 24.10 24.10
5,000 15.50 15.50
13 5/8
10,000 24.10 24.10
18 3/4 10,000 58.00 58.00
64 Coiled Tubing Data

Hydril Type 'GL' Annular Preventer

BOP Nom. Working Fluid to Fluid to Secondary
Size (In.) Pressure (psi) Close (gal) Open (gal) Fluid (gal)

13 5/8 5,000 19.76 19.76 8.24

16 3/4 5,000 33.80 33.80 17.30
18 3/4 5,000 44.00 44.00 20.00
21 1/4 5,000 58.00 58.00 29.50
Hydril Manual Lock Ram Preventer
BOP Nom. Working Fluid to Close Fluid to Open
Size (In.) Pressure (psi) (gal) (gal)
3,000 1.00 0.93
5,000 1.00 0.93
7 1/16
10,000 1.90 1.80
15,000 3.70 3.40
3,000 1.90 1.90
9
5,000 1.90 1.90
3,000 3.30 3.20
11 5,000 3.30 3.20
10,000 5.20 5.50
3,000 5.40 4.90
13 5/8 5,000 5.40 4.80
10,000 12.20 11.60
18 3/4 5,000 17.10 16.10
20 3/4 3,000 8.10 7.20
2,000 8.10 7.20
21 1/4
5,000 17.50 16.60
Hydril MPL Ram Preventer
BOP Nom. Working Fluid to Close Fluid to Open
Size (In.) Pressure (psi) (gal) (gal)
3,000 1.20 0.93
5,000 1.20 0.93
7 1/16
10,000 2.00 1.80
15,000 3.90 3.40
10,000 5.70 5.00
11
20,000 12.50 11.50
3,000 5.90 4.90
5,000 5.90 5.20
13 5/8
10,000 12.80 11.60
15,000 12.60 11.00
5,000 17.90 16.10
18 3/4 10,000 17.10 15.60
15,000 19.40 16.70
20 3/4 3,000 18.00 16.30
2,000 18.00 16.30
21 1/4
5,000 19.30 16.60
 Coiled Tubing Data 65

Coile
Coiled
d Tubing Stre
Stretch Table
Cross
Size (In) Wall Free Point
Sectional
Area (Sq In)
OD Thickness Constant
(In)
.08 .30 760.0
7 4
.095 .328 820.0
.10 .35 877.5
2 1
1.250 .10 .37 935.0
9 4
.125 .420 1050.0
.13 .45 1127.5
4 1
.15 .51 1280.0
6 2
.095 .399 997.5
.10 .42 1070.0
2 8
.10 .45 1140.0
1.500 9 6
.125 .512 1280.0
.13 .55 1380.0
4 2
.15 .62 1572.5
6 9
.109 .538 1345.0
.12 .60 1512.5
5 5
1.750 .13 .65 1630.0
4 2
.156 .745 1862.5
.17 .83 2077.5
5 1
.10 .61 1547.5
9 9
.125 .698 1745.0
2. .13 .75 1882.5
0 4 3
.15 .86 2152.5
6 1
.175 .962 2405.0
.12 .83 2092.5
5 7
.13 .90 2260.0
4 4
2.375 .156 1.035 2587.5
.17 1.158 2895.5
5
.19 1.241 3102.5
 Nom Displacement External Displacemen External
Internal

6
OD Wall ID Internal Displacement/ OD Wall ID Nom Displacemen
. Wt of Capacity t
Specified Specifie Calculate Specified Specifie Calculated Wt
lbs/ft ft t
Gallons bbls Gallons bbls Gallons bbls d lbs/ft Gallons bbls Gallons bbls Gallons bbls
1.00 .080 .840 .788 .02879 .00068 .0120 .0002 .0408 .00097 1.50 .116 1.268 1.719 .0656 .00156 .0262 .0006 .0918 .0021
5 1 9 0 0 2 0 2 0 9

Coiled Tubing
1.00 .087 .826 .850 .02784 .00066 .0129 .0003 .0408 .00097 1.50 .125 1.250 1.840 .0637 .00151 .0280 .0006 .0918 .0021
1.00 .095 .810 .920 .02677 3
.00063 6
.0140 1
.0003 0
.0408 .00097 1.50 .134 1.232 1.960 5
.0619 8
.00147 5
.0298 7
.0007 0
.0918 9
.0021
1.00 .102 .796 .981 .02585 7
.00061 3
.0149 3
.0003 0
.0408 .00097 1.50 .145 1.210 2.104 3
.0597 4
.00142 7
.0320 1
.0007 0
.0918 9
.0021
1.00 .109 .782 1.040 6
.02495 .00059 5
.0158 6
.0003 0
.0408 .00097 1.50 .156 1.188 4
2.245 .0575 2
.00137 6
.0342 6
.0008 0
.0918 9
.0021
1.25 .080 1.090 1.002 4
.04847 .00115 5
.0152 8
.0003 0
.0637 .00152 1.50 .175 1.150 8
2.483 .0539 1
.00128 2
.0378 1
.0009 0
.0918 9
.0021
1.25 .087 1.076 1.083 .04724 4
.00112 8
.0165 6
.0003 5
.0637 .00152 1.50 .190 1.120 2.665 6
.0511 5
.00121 4
.0406 0
.0009 0
.0918 9
.0021
1.25 .095 1.060 1.175 .04584 5
.00109 1
.0179 9
.0004 5
.0637 .00152 1.75 .109 1.532 1.915 8
.0957 9
.00228 2
.0291 7
.0007 0
.1249 9
.0029
1.25 .102 1.046 1.254 1
.04464 .00106 1
.0191 3
.0004 5
.0637 .00152 1.75 .116 1.518 6
2.029 .0940 0
.00223 9
.0309 0
.0007 5
.1249 8
.0029
1.25 .109 1.032 1.332 .04345 3
.00103 1
.0203 6
.0004 5
.0637 .00152 1.75 .125 1.500 2.175 2
.0918 8
.00218 3
.0331 4
.0007 5
.1249 8
.0029
1.25 .116 1.018 1.408 .04228 5
.00100 0
.0214 8
.0005 5
.0637 .00152 1.75 .134 1.482 2.318 0
.0896 6
.00213 5
.0353 9
.0008 5
.1249 8
.0029
1.25 .125 1.000 1.506 7
.04080 .00097 7
.0229 1
.0005 5
.0637 .00152 1.75 .145 1.460 1
2.492 .0869 4
.00207 4
.0379 4
.0009 5
.1249 8
.0029
1.25 .134 .982 1.601 1
.03934 .00093 5
.0244 5
.0005 5
.0637 .00152 1.75 .156 1.438 7
2.662 .0843 1
.00200 8
.0405 0
.0009 5
.1249 8
.0029
1.25 .145 .960 1.715 .03760 7
.00089 1
.0261 8
.0006 5
.0637 .00152 1.75 .175 1.400 2.951 7
.0799 9
.00190 8
.0449 7
.0010 5
.1249 8
.0029
1.25 .156 .938 1.827 .03590 5
.00085 5
.0278 2
.0006 5
.0637 .00152 1.75 .188 1.374 3.140 7
.0770 4
.00183 8
.0479 7
.0011 5
.1249 8
.0029
1.25 .175 .900 2.014 5
.03305 .00078 5
.0307 6
.0007 5
.0637 .00152 1.75 .190 1.370 3
3.173 .0765 4
.00182 2
.0483 4
.0011 5
.1249 8
.0029
1.50 .095 1.310 1.429 7
.07002 .00166 0
.0217 3
.0005 5
.0918 .00219 2.00 .109 1.782 8
2.207 .1295 3
.00308 7
.0336 5
.0008 5
.1632 8
.0038
1.50 .102 1.296 1.527 .06853 7
.00163 8
.0232 2
.0005 0
.0918 .00219 2.00 .116 1.768 2.340 6
.1275 5
.00303 4
.0356 0
.0008 0
.1632 9
.0038
1.50 .109 1.282 1.623 .06706 2
.00159 7
.0247 5
.0005 0
.0918 .00219 2.00 .125 1.750 2.509 3
.1249 7
.00297 7
.0382 5
.0009 0
.1632 9
.0038
 Nom. Displacement External Displacement External
OD Wall ID Internal OD Wall ID Nom Internal
Wt of Displacement/ft Of Steel Displacement
Specified Specified Calculated Specified Specifie Calculated Wt Capacity
lbs/ft d
Gallons bbls Gallons bbls Gallons bbls lbs/ft Gallons bbls Gallons bbls Gallons bbls
2.00 .134 1.732 2.677 .12239 .00291 .04081 .00097 .16320 .00389 2.875 .156 2.563 4.541 .26801 .00638 .06922 .00165 .33724 .0080
2.00 .145 1.710 2.880 4
.11930 .00284 .04390 .00105 .16320 .00389 2.875 .175 2.525 5.059 1
.26013 .00619 3
.07711 .00184 .33724 .0080

Coiled Tubing
2.00 .156 1.688 3.080 1
.11625 .00276 .04695 .00112 .16320 .00389 2.875 0.188 2.499 5.400 3
.25480 .00606 3
.08244 .00196 .33724 .0080
2.00 .175 1.650 3.419 .11108 8
.00264 .05212 .00124 .16320 .00389 2.875 0.190 2.495 5.462 .25398 7
.00604 .08326 .00198 .33724 3
.0080
2.00 .188 1.624 3.640 .10760 5
.00256 .05560 .00132 .16320 .00389 2.875 0.203 2.469 5.790 .24872 7
.00592 .08852 .00211 .33724 3
.0080
2.00 .190 1.620 3.682 2
.10708 .00254 .05612 .00134 .16320 .00389 2.875 0.204 2.467 5.834 2
.24831 .00591 3
.08893 .00212 .33724 .0080
2.00 .203 1.594 3.900 .10367 9
.00246 .05953 .00142 .16320 .00389 3.500 0.134 3.232 4.820 .42619 2
.01014 .07361 .00175 .49980 3
.0119
2.00 .204 1.592 3.923 .10341 8
.00246 .05979 .00142 .16320 .00389 3.500 0.156 3.188 5.570 .41466 7
.00987 .08514 .00203 .49980 0
.0119
2.375 .125 2.125 3.011 2
.18424 .00438 .04590 .00109 .23014 .00548 3.500 0.175 3.150 6.230 3
.40484 .00963 0
.09496 .00226 .49980 .0119
2.375 .134 2.107 3.215 7
.18113 .00431 .04901 .00117 .23014 .00548 3.500 0.188 3.124 6.650 9
.39818 .00948 0
.10162 .00242 .49980 .0119
2.375 .145 2.085 3.462 .17737 3
.00422 .05277 .00126 .23014 .00548 3.500 0.190 3.120 6.733 .39716 1
.00945 .10264 .00244 .49980 0
.0119
2.375 .156 2.063 3.706 .17364 3
.00413 .05649 .00135 .23014 .00548 3.500 0.203 3.094 7.150 .39057 6
.00929 .10923 .00260 .49980 0
.0119
2.375 .175 2.025 4.122 4
.16731 .00398 .06283 .00150 .23014 .00548 3.500 0.204 3.092 7.199 9
.39007 .00928 0
.10973 .00261 .49980 .0119
2.375 .188 1.999 4.390 3
.16304 .00388 .06710 .00160 .23014 .00548 3.500 0.224 3.052 7.857 7
.38004 .00904 0
.11976 .00285 .49980 .0119
2.375 .190 1.995 4.445 .16239 2
.00386 .06775 .00161 .23014 .00548 3.500 0.250 3.000 8.699 .36720 9
.00874 .13260 .00316 .49980 0
.0119
2.375 .203 1.969 4.710 .15818 6
.00376 .07196 .00171 .23014 .00548 4.500 0.204 4.092 9.383 .68317 3.01626 .14303 .00341 .82620 0
.0196
2.375 .204 1.967 4.742 6
.15786 .00375 .07228 .00172 .23014 .00548 4.500 0.224 4.052 6
10.255 .66988 .01595 7
.15632 .00372 .82620 .0196
2.875 .125 2.625 3.670 .28114 9
.00669 .05610 .00134 .33724 .00803 4.500 0.250 4.000 11.376 .65280 0
.01554 .17340 .00413 .82620 7
.0196
4 3 7

6
 Breaking Weight Armor Wires Wire BS – CDR Resistance Maximum
Cable Type Size (In.) Diameter (In.)

6
Strength (lbs) (Out/In) lbs (Ohms/Mft) Temp
(°F)
1-H-100-A 1/10 .101 1,00 19 18/12 41/41 25.2 300
1-H-125-A 1/8 .123 0
1,50 27 18/12 60/60 25.2 300
1-H-125-K 1/8 .123 0
1,50 28 18/12 60/60 25.2 500
1-H-181-A 3/16 .185 0
3,90 63 15/12 198/127 9.8 300
1-H-181-D 3/16 .185 0
3,90 65 15/12 198/127 9.8 420
1-H-181-K 3/16 .185 0
3,90 65 15/12 198/127 9.8 500
1-H-181-M 3/16 .187 0
3,60 68 15/12 198/132 12.5 600

Electric
4-H-181-A 3/16 .186 0
3,30 60 18/18 143/76 26.0 300
1-H-203-A 13/64 .203 0
4,50 79 16/10 212/212 6.9 300
1-H-203-D 13/64 .203 0
4,50 79 16/10 212/212 6.9 420
1-H-203-K 13/64 .203 0
4,50 80 16/10 212/212 6.9 500
1-H-220-A 7/32 .223 0
5,50 92 18/12 212/212 4.5 300
1-H-220-D 7/32 .223 0
5,50 95 18/12 212/212 4.5 420
1-H-220-K 7/32 .223 0
5,50 95 18/12 212/212 4.5 500
1-H-226-K 7/32 .222 0
5,00 99 18/12 196/196 7.7 500
1-H-281-A 9/32 .288 0
10,000 153 18/12 352/352 2.8 300
1-H-281-K 9/32 .288 10,000 158 18/12 352/352 2.8 500
1-H-314-A 5/16 .316 11,200 183 18/12 426/426 2.8 300
1-H-314-D 5/16 .316 11,200 187 18/12 426/426 2.8 420
1-H-314-K 5/16 .316 11,200 190 18/12 426/426 2.8 500
7-H-314-A 5/16 .323 9,60 180 18/18 426/225 16.6 300
 Breaking Weight (lbs) Armor Wires Wire BS – lbs CDR Resistance Maximum Temp
Cable Type Size (In.) Diameter (In.)
Strength 1000ft (Out/In) (Out/In) (Ohms/Mft) (°F)
1-H-375-A 3/8 .375 (lbs)
14,600 253 18/12 595/595 2.9 300
1-H-375-D 3/8 .375 14,600 260 18/12 595/595 2.9 420
1-H-375-K 3/8 .375 14,600 261 18/12 595/595 2.9 500
3-H-375-A 3/8 .372 13,500 235 20/16 486/397 7.1 300
4-H-375-A 3/8 .372 13,500 239 20/16 572/301 10.5 300
7-H-375-A 3/8 .372 12,800 243 18/18 572/301 10.5 300

Electric
1-H-422-A 7/16 .414 17,800 307 18/12 727/727 2.9 300
1-H-422-D 7/16 .414 17,800 316 18/12 727/727 2.9 420
1-H-422-K 7/16 .414 17,800 317 18/12 727/727 2.9 500
7-H-422-A 7/16 .426 18,300 314 18/18 766/397 10.9 300
7-H-422-D 7/16 .426 18,300 324 18/18 766/397 10.0 420
7-H-422-K 7/16 .426 18,300 326 18/18 766/397 10.0 500
7-H-464-A 15/32 .462 18,300 326 24/24 539/335 10.0 300
7-H-464-D 15/32 .462 18,300 333 24/24 539/335 10.0 420
7-H-464-K 15/32 .462 18,300 347 24/24 539/335 10.0 500
7-H-520-A 17/32 .522 26,000 462 20/16 958/778 10.5 300
7-H-520-D 17/32 .522 26,000 467 20/16 958/778 10.5 420
7-H-472-A Slammer .472 22,200 379 18/18 929/486 10.0 300
7-H-472-D Slammer .472 22,200 386 18/18 929/486 10.0 420
7-H-472-K Slammer .472 22,200 394 18/18 929/486 10.0 500

6
 Carbon Steel – API 9A Breaking

7
Strengths
Sinker Bar Weight Needed

4
0
8
4
0
2
5
0
6
5
0
0
6
0
4
6
0
8
6
0
2
7
Material (In) .072 .082 .092 .105 .108
Br. Steel API Level 3 or improved plow 961 1239 1547 1966 2109 2794
(lbs)
API Ex. Impr. Plow, Hi-Str, or Mon. AA 1150 1460 1830 2360 2490 3300
1000
(lbs)
Austeniti Stainless Steel Breaking Strengths
c –
Material (In) .082 .092 .105 .108

Wireline
2000
For wirelne to fall against .125
316 Stainless 1083 1363 1732 1786 2270
well
pressure, find desired line (lbs)
3000 Super enitic Stainless – Breaking Strengths
versus well pressure and Aust
Material (In) .092 .105 .108
extrapolate total sinker bar
Well Pressure

4000 .125
weight needed. Sandvik Sanicro 28 (lbs) 1445 1885 1995 2675
6 Moly St ainless Steel – Breaking Strengths
5000
All “lbs” are breaking Material (In) .092 .105 .108
.125
6000 strength. These vary with Avesta 254 SMO (lbs) 1462 1818 1924 2454
the
manufacturer. Bridon Supa (lbs) 1550 2030 2030 2560
7000 25-6MO (lbs) 1475 N/A 2050 2550
Cobalt Based Alloy – eaking Strengths
8000 Br
Material (In) .092 .105 .108
.125
MP35N 1582 2009 2080 2724
9000
(lbs)
Braided Line – Breaking
Strengths
10000 Size (In) 3/16” 3/16” 7/32”
.100

7/32”
Construction 1 x 16 1x 19 (Dycan/Dyform) 1 x 16 1x 19 (Dycan/Dyform)
Galv. Carbon Steel 4500 6170 6000 8370
15-6Mo (Supa 75) 4320 4960 5842 5990
 Conversion Factors
71

Fiel
Field
d Units to Metric Conve
Conversion
If You Multiply By: To Get:
Have:

Feet x 0.3048 Meters (M)

Inches x 2.54 Centimeters
(cm) Inches x 25.4
Millimeters (mm)
Pounds
x Metric Tons
(Lbs)
0.0004536
Pounds (Lbs) x 0.44482 Decanewtons
(daN) Pounds x 0.4536
Kilograms
Weight (Lbs/ft) x
Kg/M
1.4882
Pounds per Barrel x 2.85307 Kg/M3
Barrels x 158.987 Liters
Barrels x
Cubic Meters
0.15898
Gallons x 3.7854 Liters
Gallons x 0.0037854 Cubic Meters
Barrels/Stroke x
Liters/Stroke
158.987
Barrels/Stroke x 0.158987 Cubic
Meters/Stroke
Gallons/Minute x 3.7854 Liters/Minute
Barrels/Minute x
Liters/Minute
158.987
Barrels/Minute x 0.158987 Cubic
Meters/Minute bbl/ft. Capacity x 521.612
Liters/Meter (L/M)
bbl/ft. Capacity x
Cubic Meters/Meter
0.521612
Bbl Displacement x 521.612 Liters/Meter (L/M)
Bbl Displacement x 0.521612 Cubic Meters/Meter
Gradient psi/ft x
KPa/M
22.6206
Gradient psi/ft x 0.226206 Bar/M
Mud Weight PPG x 0.119826 Kilograms/Liter
(Kg/L)
Mud Weight PPG x
Kilograms/Cubic Meter
119.826
Mud Weight PPG x 0.119826 Specific Gravity
(SG) Mud Weight (Lb/Ft3) x 1.60185 Kg/M3
Fahrenheit Degrees x 0.56 –
Celsius Degrees
17.8
PSI x 6894.8 Pascals (Pa)
PSI x 6.8948 Kilopascals (KPa)
PSI x
Bar
0.06895
BWPD @ 8.9 ppg X 0.118 Kg/Min
BOPD @ 7.74 ppg X 0.099 Kg/Min
mmCFD @ 0.6 sp. gr. X
Kg/Min
14.1
72 Conversion Factors

Metric to Fiel
Field
d Units Conve
onversion
If You Have: Multiply By: To Get:

Meters (m) x 3.2808 Feet

Centimeters (cm) x 0.3937 Inches
Millimeters (mm) x 0.03937 Inches
Metric Tons x 2204.6 Pounds (Lbs)
Decanewtons (daN) x 0.22481 Pounds (Lbs)
Kilograms x 2.2046 Pounds
Kg/m x 0.67196 Weight (Lbs/Ft)
Kg/m3 x 0.3505 Pounds per Barrel
Liters x 0.00629 Barrels
Cubic Meters x 6.2898 Barrels
Liters x 0.2642 Gallons
Cubic Meters x 264.173 Gallons
Liters/Stroke x 0.00629 Barrels/Stroke
Cubic Meters/Stroke x 6.2898 Barrels/Stroke
Liters/Minute x 0.2642 Gallons/Minute
Liters/Minute x 0.00629 Barrels/Minute
Cubic Meters/Minute x 6.2898 Barrels/Minute
Liters/Meter (l/m) x 0.0019171 BBL/Ft. Capacity
Cubic Meters/Meter x 1.917 BBL/Ft. Capacity
Liters/Meter (l/m) x 0.0019171 BBL Displacement
Cubic Meters/Meter x 1.9171 BBL Displacement
KPa/m x 0.044207 Gradient PSI/Ft
Bar/m x 4.4207 Gradient PSI/Ft
Kilograms/Liter (Kg/L) x 8.3454 Mud Weight PPG
Kilograms/Cubic x 0.0083454 Mud Weight PPG
Meter
Specific Gravity (SG) x 8.3454 Mud Weight PPG
Kg/m3 x 6.24279 Mud Weight Lb/Ft3)
Celsius Degrees x 1.8 + 32 Fahrenheit Degrees
Pascals (Pa) x 0.000145 PSI
Kilopascals (KPa) x 0.14504 PSI
Bar x 14.50377 PSI
Kg/Minute X 8.475 BWPD @ 8.9 ppg
Kg/Minute X 10.105 BOPD @ 7.74 ppg
Kg/Minute X 0.071 mmCFD @ 0.6 sp.gr.
Notes & Calculations
73
74 Notes & Calculations