Scribd
Upload
15 views6 pages

Line Following Robot-1

Uploaded by

Jaya Sai
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
15 views6 pages

Line Following Robot-1

Uploaded by

Jaya Sai
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 6

LINE FOLLOWER ROBOT USING ARDUINO

AIM: Design a line Following Robot Using Arduino Uno .


APPARATUS:
• Arduino UNO
• DC Motor
• IR sensor *2
• Motor Driver L298N
• 12 Volt Battery
• Battery holder
• Robot Chasis
• Connecting wires
CIRCUIT DIAGRAM:
PROCEDURE:-

• Go to https://www.arduino.cc/en/Main/Software - select windows 7 and newer & select


just Download.
• Double click the arduino-1.8.19-windows setup file & proceed with installation by simply
clicking ‘agree & next ‘ in installation pop-up window.
• Double click Arduino icon. Go to Menu – File → New.
• Write c program for Object Following robot.
• Go to menu bar &click on verify ✅ option.(clear if any errors are there)  Go to menu –
Tools – Board – Arduino Uno R3.
• Connect your Arduino board to laptop using it’s usb cable
• Go to Tools → Port – COM3(Arduino uno)
• Go to Menu – select the right arrow icon ➡ (Upload).
• Then remove the usb cable from Arduino board
• Connect the circuit as per circuit diagram
• Make sure all the connections are made properly & avoiding loose connections.  Switch
on the power supply and verify its functionality with theoretical.
PIN CONNECTIONS:-

• RIGHT IR sensor is connected to PIN2


• LEFT IR sensor is connected to PIN3
• RIGHTMOTOR Enable pin is connected to PIN10
• RIGHT MOTOR PIN1 is connected to PIN9
• RIGHT MOTOR PIN2 is connected to PIN8
• LEFT MOTOR Enable pin is connected to PIN5  LEFT MOTOR PIN1 is connected to
PIN7
• LEFT MOTOR PIN2 is connected to PIN6.

CODE:
#define in1 9
#define in2 8
#define in3 7
#define in4 6
#define enA 10
#define enB 5

int M1_Speed = 100; // speed of motor 1


int M2_Speed = 100; // speed of motor 2
int LeftRotationSpeed = 150; // Left Rotation Speed
int RightRotationSpeed = 150; // Right Rotation Speed

void setup() {

pinMode(in1, OUTPUT);
pinMode(in2, OUTPUT);
pinMode(in3, OUTPUT);
pinMode(in4, OUTPUT);

pinMode(enA, OUTPUT);
pinMode(enB, OUTPUT);

pinMode(A1, INPUT); // initialize Left sensor as an input


pinMode(A0, INPUT); // initialize Right sensor as an input
Serial.begin(9600);
//analogWrite(enA, M1_Speed); // Write The Duty Cycle 0 to 255 Enable
Pin A for Motor1 Speed
//analogWrite(enB, M2_Speed); // Write The Duty Cycle 0 to 255 Enable
Pin B for Motor2 Speed
delay(1000);

void loop() {

int LEFT_SENSOR = digitalRead(A0);


int RIGHT_SENSOR = digitalRead(A1);

if (RIGHT_SENSOR == 0 && LEFT_SENSOR == 0) {


forward(); //FORWARD
Serial.print("l:");
Serial.println(LEFT_SENSOR);
Serial.print("r:");
Serial.println(RIGHT_SENSOR);
Serial.println("direction:forward");
// delay(1000);
}

else if (RIGHT_SENSOR == 1 && LEFT_SENSOR == 0) {


right(); //Move Right
Serial.print("l:");
Serial.println(LEFT_SENSOR);
Serial.print("r:");
Serial.println(RIGHT_SENSOR);
Serial.println("direction:r");
// delay(1000);
}

else if (RIGHT_SENSOR == 0 && LEFT_SENSOR == 1) {


left(); //Move Left
Serial.print("l:");
Serial.println(LEFT_SENSOR);
Serial.print("r:");
Serial.println(RIGHT_SENSOR);
Serial.println("direction:l");
// delay(1000);
}

else if (RIGHT_SENSOR == 1 && LEFT_SENSOR == 1) {


Stop(); //STOP
Serial.print("l:");
Serial.println(LEFT_SENSOR);
Serial.print("r:");
Serial.println(RIGHT_SENSOR);
Serial.println("direction:s");
// delay(1000);
}
}

void forward()
{
digitalWrite(in1, LOW); //Right Motor forword Pin
digitalWrite(in2, HIGH); //Right Motor backword Pin
digitalWrite(in3, HIGH); //Left Motor backword Pin
digitalWrite(in4, LOW); //Left Motor forword Pin

analogWrite(enA, M1_Speed);
analogWrite(enB, M2_Speed);
}

void backward()
{
digitalWrite(in1, HIGH);
digitalWrite(in2, LOW);
digitalWrite(in3, HIGH);
digitalWrite(in4, LOW);

analogWrite(enA, M1_Speed);
analogWrite(enB, M2_Speed);
}

void right()
{
digitalWrite(in1, LOW); //Right Motor forword Pin
digitalWrite(in2, HIGH); //Right Motor backword Pin
digitalWrite(in3, LOW); //Left Motor backword Pin
digitalWrite(in4, HIGH); //Left Motor forword Pin

analogWrite(enA, LeftRotationSpeed);
analogWrite(enB, RightRotationSpeed);
}

void left()
{
digitalWrite(in1, HIGH); //Right Motor forword Pin
digitalWrite(in2, LOW); //Right Motor backword Pin
digitalWrite(in3, HIGH); //Left Motor backword Pin
digitalWrite(in4, LOW); //Left Motor forword Pin

analogWrite(enA, LeftRotationSpeed);
analogWrite(enB, RightRotationSpeed);
}

void Stop()
{
digitalWrite(in1, LOW);
digitalWrite(in2, LOW);
digitalWrite(in3, LOW);
digitalWrite(in4, LOW);
}

Observations:-

• When object is present in front of ultrasonic sensor then the robo will move forward.
• When the object is nearer to the right IR sensor,it turns right.
• When the object is near left IR sensor, it turns left .
• When the object covers both IR sensors,then the robo will stop
• Result:-
Thus designed line Following Robot on Arduino Uno & verified its functionality.

You might also like