101401-7590 ZEXEL test values diesel fuel-injection equipment 16.12.
10 13:45:37 Page 1
ZEXEL Ass'y No. 101401-7590
Bosch Ass'y No. 9 400 613 247
Bosch Typecode
Engine Type 4HF1
Manufacturer ISUZU
Edition date 01.03.06 (1)
1 Adjustment conditions
CAT Designation Unit Set value min. max. Actual values OT
Test oil ISO4113 or {SAEJ96
7d}
1404 Test oil
P Test oil temperature degC 40 40 45
Nozzle and nozzle holder 105780-8140
Bosch type code EF8511/9A
Nozzle 105780-0000
Bosch type code DN12SD12T
Nozzle holder 105780-2080
Bosch type code EF8511/9
P Opening pressure MPa 17.2
P Opening pressure kgf/cm2 175
Injection pipe mm 6-2-600
Outer diameter - inner diameter - length (mm)
Overflow valve 131424-4920
P Overflow valve opening pressure kPa 127 107 147
P Overflow valve opening pressure kgf/cm2 1.3 1.1 1.5
P Tester oil delivery pressure kPa 157 157 157
P Tester oil delivery pressure kgf/cm2 1.6 1.6 1.6
Direction of rotation (viewed from drive side) L
Left
2 Adjustment specification
2.1 Injection timing adjustment
CAT Designation Unit Set value min. max. Actual values OT
P Direction of rotation (viewed from drive side) L
Left
P Injection order 1-3-4-2
S Pre-stroke mm 4.1 4.05 4.15
S Rack position R=A
Point A
P Beginning of injection position NO.1
Governor side
S Difference between angles 1 deg. 90 89.5 90.5
Cal 1-3
S Difference between angles 2 deg. 180 179.5 180.5
Cal 1-4
S Difference between angles 3 deg. 270 269.5 270.5
Cyl.1-2
2.2 Injection quantity adjustment
CAT Designation Unit Set value min. max. Actual values OT
P Adjusting point -
P Rack position 12
P Pump speed r/min 960 960 960
S Average injection quantity mm3/st. 57 55.4 58.6
S Max. variation between cylinders % 0 -4 4
P Basic *
P Fixing the rack *
P Standard for adjustment of the maximum vari *
ation between cylinders
CAT Designation Unit Set value min. max. Actual values OT
P Adjusting point H
P Rack position 9.8+-0.5
P Pump speed r/min 285 285 285
S Average injection quantity mm3/st. 15.5 14.2 16.8
S Max. variation between cylinders % 0 -10 10
P Fixing the rack *
P Standard for adjustment of the maximum vari *
ation between cylinders
CAT Designation Unit Set value min. max. Actual values OT
P Adjusting point A
P Rack position R1(12)
P Pump speed r/min 960 960 960
S Average injection quantity mm3/st. 57 56 58
P Basic *
S = Setting value, C = Check value)
OT = Outside Tolerance (X is set)
101401-7590 ZEXEL test values diesel fuel-injection equipment 16.12.10 13:45:37 Page 2
P Fixing the lever *
CAT Designation Unit Set value min. max. Actual values OT
P Adjusting point B
P Rack position R1+0.1
P Pump speed r/min 1600 1600 1600
S Average injection quantity mm3/st. 68.5 64.5 72.5
P Fixing the lever *
CAT Designation Unit Set value min. max. Actual values OT
P Adjusting point C
P Rack position R1-0.2
P Pump speed r/min 500 500 500
S Average injection quantity mm3/st. 45.1 41.1 49.1
P Fixing the lever *
2.3 Governor adjustment
Name
T1=L48 N:Pump speed
R:Rack position (mm)
(1)Torque cam stamping: T1
(2)Tolerance for racks not indicated: +-0.05mm.
2.4 Timer adjustment
CAT Designation Unit Set value min. max. Actual values OT
S Pump speed r/min 1050--
P Advance angle deg. 0 0 0
Remarks
Start
CAT Designation Unit Set value min. max. Actual values OT
S = Setting value, C = Check value)
OT = Outside Tolerance (X is set)
101401-7590 ZEXEL test values diesel fuel-injection equipment 16.12.10 13:45:37 Page 3
P Pump speed r/min 1000
S Advance angle deg. 0.5 0.5
CAT Designation Unit Set value min. max. Actual values OT
P Pump speed r/min 1600
S Advance angle deg. 5 4.5 5.5
Remarks
Finish
2.5 Speed control lever angle
Name
a=41deg+-5deg
b=35.5deg+-3deg
F:Full speed
I:Idle
(1)Stopper bolt set position 'H'
2.6 Stop lever angle
Name
a=23deg+-5deg
b=(29deg)+-5deg
aa=58mm N:Pump normal
bb=1600r/min S:Stop the pump.
cc=5+-0.2mm (1)Use the hole at R = aa
(2)At pump speed bb and rack position cc, set the stopper bolt.
S = Setting value, C = Check value)
OT = Outside Tolerance (X is set)
101401-7590 ZEXEL test values diesel fuel-injection equipment 16.12.10 13:45:37 Page 4
2.7 Timing setting
Name
a=(60deg)
b=(85deg)
aa=8deg (1)Pump vertical direction
(2)Position of gear's standard threaded hole at No 1 cylinder's beginning of injection
(3)Stamping position on the A/T outer rim
(4)Pump bracket check hole position.
(5)At the No 1 cylinder's beginning of injection, align with the projection seen through the bracket'
s check hole and mark the A/T's bevel C1.
(6)B.T.D.C.: aa
S = Setting value, C = Check value)
OT = Outside Tolerance (X is set)
