LP156WH3

Liquid Crystal Display

Product Specification

SPECIFICATION
FOR

.tw
APPROVAL

om
( ) Preliminary Specification
( ◆ ) Final Specification

d.c Title 15.6” HD TFT LCD

Customer SUPPLIER LG Display Co., Ltd.

MODEL *MODEL LP156WH3

Suffix TPS1
*When you obtain standard approval,
slc
please use the above model name without suffix

APPROVED BY SIGNATURE APPROVED BY SIGNATURE

w.y

J. Y. Lee / S.Manager
/
REVIEWED BY

/
J. S. Park / Manager
ww

/ PREPARED BY

K. T. Baek / Engineer
J. K. Han / Engineer

Please return 1 copy for your confirmation with Products Engineering Dept.
your signature and comments. LG Display Co., Ltd

Ver. 0.1 May. 10, 2013 1 / 34

 LP156WH3
Liquid Crystal Display
Product Specification

Contents

No ITEM Page
COVER 1

.tw
CONTENTS 2

RECORD OF REVISIONS 3

1 GENERAL DESCRIPTION 4

2 ABSOLUTE MAXIMUM RATINGS

om
5

3 ELECTRICAL SPECIFICATIONS

3-1 ELECTRICAL CHARACTREISTICS 6-7

3-2 INTERFACE CONNECTIONS 8

d.c
3-3

3-4
LVDS SIGNAL TIMING SPECIFICATION

SIGNAL TIMING SPECIFICATIONS

9

10

3-5 SIGNAL TIMING WAVEFORMS 10

3-6 COLOR INPUT DATA REFERNECE 11

slc
3-7 POWER SEQUENCE 12

4 OPTICAL SFECIFICATIONS 13-15

5 MECHANICAL CHARACTERISTICS 16-18

w.y

A APPENDIX. LGD PROPOSAL FOR SYSTEM COVER DESIGN 19-23

6 RELIABLITY 24

7 INTERNATIONAL STANDARDS

7-1 SAFETY 25
ww

7-2 EMC 25

7-3 Environment 25

8 PACKING

8-1 DESIGNATION OF LOT MARK 26

8-2 PACKING FORM 26

9 PRECAUTIONS 27-28

A APPENDIX. Enhanced Extended Display Identification Data 29-31

Ver. 0.1 May. 10, 2013 2 / 34

 LP156WH3
Liquid Crystal Display
Product Specification

RECORD OF REVISIONS

EDID
Revision No Revision Date Page Description

.tw
ver
0.0 May. 10. 2013 - First Draft (Preliminary Specification) -
1.0 Jul. 16. 2013 12 Update Power Sequence Table
- Final Version. 1.0

om
d.c
slc
w.y
ww

Ver. 0.1 May. 10, 2013 3 / 34

 LP156WH3
Liquid Crystal Display
Product Specification

1. General Description
The LP156WH3 is a Color Active Matrix Liquid Crystal Display with an integral LED backlight system. The
matrix employs a-Si Thin Film Transistor as the active element. It is a transmissive type display operating in
the normally black mode. This TFT-LCD has 15.6 inches diagonally measured active display area with HD
resolution (1366 horizontal by 768 vertical pixel array). Each pixel is divided into Red, Green and Blue sub-
pixels or dots which are arranged in vertical stripes. Gray scale or the brightness of the sub-pixel color is

.tw
determined with a 6-bit gray scale signal for each dot, thus, presenting a palette of more than 262,144
colors. The LP156WH3 has been designed to apply the interface method that enables low power, high
speed, low EMI. The LP156WH3 is intended to support applications where thin thickness, low power are
critical factors and graphic displays are important. In combination with the vertical arrangement of the sub-
pixels, the LP156WH3 characteristics provide an excellent flat display for office automation products such
as Notebook PC.

om
EEPROM Block 1 1366
for Tcon & EDID
User connector

d.c AUX
Timing Control
TFT-LCD Panel
(HD, GIP, TN)
eDP (Tcon) Block
1 Lane
768
DVCC TCLKs
30
slc
Pin

VCC DVCC, AVDD

Power Source Driver
VGH, VGL, GMA
Block (Bottom)
GIP CLKs, DSC

VLED VOUT_LED
LED Driver
FB1~2
LED Backlight Ass’y
LED_EN
w.y

PWM Block

Control & Data Power EDID signal & Power

General Features
Active Screen Size 15.6 inches diagonal
ww

Outline Dimension 359.5(H, Typ.) × 217.2(V, Typ.) × 3.8(D, Max.) [mm] (with PCB Board)
Pixel Pitch 0.252mm X 0.252 mm
Pixel Format 1366 horiz. by 768 vert. Pixels RGB strip arrangement
Color Depth 6-bit, 262,144 colors
Luminance, White 200 cd/m2(Typ.)
Power Consumption Total 3.2W (Typ.) Logic : 0.7W (Typ.@ Mosaic), B/L : 2.5W (Typ.@VLED12V)
Weight 400g (Max.)
Display Operating Mode Transmissive mode, normally white
Surface Treatment Glare treatment of the front Polarizer
RoHS Compliance Yes
BFR / PVC / As Free Yes for all

Ver. 0.1 May. 10, 2013 4 / 34

 LP156WH3
Liquid Crystal Display
Product Specification

2. Absolute Maximum Ratings

The following are maximum values which, if exceeded, may cause faulty operation or damage to the unit.

Table 1. ABSOLUTE MAXIMUM RATINGS

.tw
Values
Parameter Symbol Units Notes
Min Max
Power Input Voltage VCC -0.3 4.0 Vdc at 25  5C

C

om
Operating Temperature TOP 0 50 1

Storage Temperature HST -20 60 C 1

Operating Ambient Humidity HOP 10 90 %RH 1

Storage Humidity
d.c HST 10 90 %RH 1

Note : 1. Temperature and relative humidity range are shown in the figure below.
Wet bulb temperature should be 39C Max, and no condensation of water.
Note : 2. Storage Condition is guaranteed under packing condition.
slc
90% 80%

60 60%
w.y

Wet Bulb 50
Humidity[(%)RH]

Temperature [℃] Storage

40 40%

30 Operation
20
20%
ww

10
0
10%

-20 0 10 20 30 40 50 60 70 80

Dry Bulb Temperature [℃]

Ver. 0.1 May. 10, 2013 5 / 34

 LP156WH3
Liquid Crystal Display
Product Specification

3. Electrical Specifications
3-1. Electrical Characteristics
The LP156WH3 requires two power inputs. The first logic is employed to power the LCD electronics and to
drive the TFT array and liquid crystal. The second backlight is the input about LED BL with LED Driver.

Table 2. ELECTRICAL CHARACTERISTICS

.tw
Values
Parameter Symbol Unit Notes
Min Typ Max
LOGIC :

om
Power Supply Input Voltage VCC 3.0 3.3 3.6 V 1
Power Supply Input Current Mosaic ICC - 220 255 mA 2
Power Consumption PCC - 0.7 0.8 W 2
Power Supply Inrush Current ICC_P - - 1500 mA 3
d.c
Differential Impedance
BACKLIGHT : ( with LED Driver)
Zm 90 100 110 Ω 4

LED Power Input Voltage VLED 7.0 12.0 21.0 V 5

LED Power Input Current ILED - 210 230 mA 6
slc
LED Power Consumption PLED - 2.5 2.8 W 6
LED Power Inrush Current ILED_P - - 2000 mA 7
PWM Duty Ratio 5 - 100 % 8
w.y

PWM Jitter - 0 - 0.2 % 9

PWM Impedance ZPWM 20 40 60 kΩ

PWM Frequency FPWM 200 - 1000 Hz 10

PWM High Level Voltage VPWM_H 3.0 - 3.6 V

ww

PWM Low Level Voltage VPWM_L 0 - 0.3 V

LED_EN Impedance ZPWM 20 40 60 kΩ
LED_EN High Voltage VLED_EN_H 3.0 - 3.6 V
LED_EN Low Voltage VLED_EN_L 0 - 0.3 V
Life Time 12,000 - - Hrs 11

Ver. 0.1 May. 10, 2013 6 / 34

 LP156WH3
Liquid Crystal Display
Product Specification

Note)
1. The measuring position is the connector of LCM and the test conditions are under 25℃, fv = 60Hz,
Black pattern.
2. The specified Icc current and power consumption are under
the Vcc = 3.3V , 25℃, fv = 60Hz condition and Mosaic pattern.

.tw
2. This Spec. is the max load condition for the cable impedance designing.
3. The below figures are the measuring Vcc condition and the Vcc control block LGD used.

m
The Vcc condition is same as the minimum of T1 at Power on sequence.

Rising time
Vcc

0V 10%
90%
d
0.5ms
3.3V

.co
slc
4. This impedance value is needed for proper display and measured form eDP Tx to the mating connector.
5. The measuring position is the connector of LCM and the test conditions are under 25℃.
w.y

6. The current and power consumption with LED Driver are under the Vled = 12.0V , 25℃, Dimming of
Max luminance and White pattern with the normal frame frequency operated(60Hz).
7. The below figures are the measuring Vled condition 12.0V
and the Vled control block LGD used. Rising time 90%
VLED control block is same with Vcc control block. VLED
ww

0V 10%
0.5ms

8. The operation of LED Driver below minimum dimming ratio may cause flickering or reliability issue.
9. If Jitter of PWM is bigger than maximum, it may induce flickering.
10. This Spec. is not effective at 100% dimming ratio as an exception because it has DC level equivalent
to 0Hz. In spite of acceptable range as defined, the PWM Frequency should be fixed and stable for
more consistent brightness control at any specific level desired.
11. The life time is determined as the time at which brightness of LCD is 50% compare to that of minimum
value specified in table 7. under general user condition.

Ver. 0.1 May. 10, 2013 7 / 34

 LP156WH3
Liquid Crystal Display
Product Specification

3-2. Interface Connections

This LCD employs two interface connections, a 30 pin connector used for the module electronics interface and
the other connector used for the integral backlight system.

Table 3. MODULE CONNECTOR PIN CONFIGURATION (CN1)

.tw
Pin Symbol Description Notes
1 NC NO Connect [Interface Chip]
1. LCD :
2 GND High Speed (Main Link) Ground
SW0661A (LCD Controller
3 NC NO Connect Including eDP Receiver.
2. System : TBD or equivalent
4 NC NO Connect

om
* Pin to Pin compatible with eDP
5 GND High Speed (Main Link) Ground
[Connector]
6 Lane0_N Complement Signal-Lane 0
KN38-30S-0.5H or equivalent
7 Lane0_p True Signal-Main Lane 0
[Connector pin arrangement]
8 GND High Speed (Main Link) Ground
9

10
d.c AUX_P

AUX_N
True Signal-Auxiliary Channel

Complement Signal-Auxiliary Channel

30 1

11 GND High Speed (Main Link) Ground

12 VCC LCD Logic and driver power (3.3V Typ.)
[LCD Module Rear View]
13 VCC LCD Logic and driver power (3.3V Typ.)
slc
14 NC NO Connect
[LGD P-Vcom Share pin]
15 GND Ground 1. Pin for P-Vcom : #24, #25
16 GND Ground 2. P-Vcom Address : 01010000

17
w.y

HPD HPD signal pin

18 GND LED Backlight Ground
19 GND LED Backlight Ground
20 GND LED Backlight Ground
21 GND LED Backlight Ground
ww

22 LED_EN LED Backlight On/Off

23 PWM System PWM Signal input for dimming

24 Clk EEDID DDC Clock (LGD P-Vcom Share Pin)

25 DATA EEDID DDC Data (LGD P-Vcom Share Pin)

26 VLED LED Backlight Power (7.0V-21V)

27 VLED LED Backlight Power (7.0V-21V)

28 VLED LED Backlight Power (7.0V-21V)

29 VLED LED Backlight Power (7.0V-21V)

30 NC NO Connect

Ver. 0.1 May. 10, 2013 8 / 34

 LP156WH3
Liquid Crystal Display
Product Specification

3-3. eDP Signal Timing Specifications

3-3-1. DC Specification
The VESA Display Port related AC specification is compliant with the VESA Display Port Standard.

.tw
om
d.c Description Symbol Min
120
Max
-
Unit Notes
For high bit rate
Differential peak-to-peak Input voltage VDIFF p-p mV
40 - For reduced bit rate
Rx DC common mode voltage VCM 0 2.0 V -
slc
3-3-2. AC Specification
The VESA Display Port related AC specification is compliant with the VESA Display Port Standard.
w.y

Description Symbol Min Typ Max Unit Notes

Unit Interval for high bit rate

UI_High_Rate - 370 - ps Range is nominal ±350ppm.
(2.7Gbps/lane) DisplayPort Link Rx does not
ww

require local crystal for link

Unit Interval for high bit rate clock generation
UI_Low_Rate - 617 - ps
(1.62Gbps/lane)

V Rx-SKEW-
Lane-to-Lane skew - - 5200 ps -
INTER_PAIR

V Rx-SKEW- - - 100 ps For high bit rate

Lane intra-pair skew
INTRA_PAIR - - 300 ps For reduced bit rate

Ver. 0.1 May. 10, 2013 9 / 34

 LP156WH3
Liquid Crystal Display
Product Specification

3-4. Signal Timing Specifications

This is the signal timing required at the input of the User connector. All of the interface signal timing should be
satisfied with the following specifications and specifications of eDP Tx/Rx for its proper operation.

Table 4. TIMING TABLE

.tw
ITEM Symbol Min Typ Max Unit Note

DCLK Frequency fCLK - 76.3 - MHz

Period tHP 1586 1610 1632

Hsync Width tWH 32 32 48 tCLK

Width-Active tWHA 1366 1366 1366

om
Period tVP 780 790 796

Vsync Width tWV 3 5 7 tHP

Width-Active tWVA 768 768 768

Horizontal back porch tHBP 156 164 170

tCLK
Horizontal front porch tHFP 32 48 48
Data
d.c
Enable Vertical back porch

Vertical front porch

tVBP

tVFP
7

2
14

3
16

5
tHP

Appendix) all reliabilities are specified for timing specification based on refresh rate of 60Hz. However,
LP156WH3 has a good actual performance even at lower refresh rate (e.g. 40Hz or 50Hz) for power saving
slc
mode, whereas LP156WH3 is secured only for function under lower refresh rate. 60Hz at Normal mode, 50Hz,
40Hz at Power save mode. Don’t care Flicker level (power save mode).

3-5. Signal Timing Waveforms Condition : VCC =3.3V

w.y

High: 0.7VCC
Data Enable, Hsync, Vsync
Low: 0.3VCC

tCLK 0.5 Vcc

DCLK
ww

tHP
Hsync tWH
tHBP tWHA tHFP

Data Enable
tVP
tWV
Vsync tVBP tWVA tVFP

Data Enable

Ver. 0.1 May. 10, 2013 10 / 34

 LP156WH3
Liquid Crystal Display
Product Specification

3-6. Color Input Data Reference

The brightness of each primary color (red, green and blue) is based on the 6-bit gray scale data input for the
color ; the higher the binary input, the brighter the color. The table below provides a reference for color
versus data input.

.tw
Table 5. COLOR DATA REFERENCE
Input Color Data
RED GREEN BLUE
Color
MSB LSB MSB LSB MSB LSB

om
R5 R4 R3 R2 R1 R0 G5 G4 G3 G2 G1 G0 B5 B4 B3 B2 B1 B0

Black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

Red 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0

Green 0 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 0

Basic Blue 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1
Color
d.c Cyan
Magenta
0

1
0

1
0

1
0

1
0

1
0 1

1 0
1

0
1

0
1

0
1

0
1 1

0 1
1

1
1

1
1

1
1

1
1

Yellow 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0

White 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
slc
RED (00) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

RED (01) 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0

RED … … … …

RED (62) 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0
w.y

RED (63) 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0

GREEN (00) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

GREEN (01) 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0

GREEN ... … … …

GREEN (62) 0 0 0 0 0 0 1 1 1 1 1 0 0 0 0 0 0 0
ww

GREEN (63) 0 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 0

BLUE (00) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

BLUE (01) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1

BLUE … … … …

BLUE (62) 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 0

BLUE (63) 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1

Ver. 0.1 May. 10, 2013 11 / 34

 LP156WH3
Liquid Crystal Display
Product Specification

3-7. Power Sequence

T1 T11
90%
Power Supply
VCC T12
10%
T2 T10

.tw
eDP Black Video Video From Source Black Video
Display
T3
HPD
from Sink
Sink
Aux CH Aux Channel Operational

om
T4 T7
Source Link
Main Link Data Training Idle Valid Video Data Idle or off
T5 T6 T8 T9

T13 T14
d.c
Power Supply
VLED
90%

10%
T15 T16
Dimming signal
Of LED B/L PWM
PWM
slc
T17 T18
LED on/off Signal
LED_EN Enabled
Table 6. POWER SEQUENCE TABLE
w.y

Required Limits Required Limits

Timing Units Notes Timing Units Notes
By Min Max By Min Max
T1 Source 0.5 10 ms - T10 Source 0 500 ms -
T2 Sink 0 200 ms - T11 Source - 10 ms -
T3 Sink 0 200 ms - VESA recommend
T12 Source 150 - ms
ww

T4 Source - - ms - Min 500ms

T5 Source - - ms - T13 Source 0.5 10 ms -

T6 Source - - ms - T14 Source 0.5 - ms -

T7 Sink 0 50 ms - T15 Source 10 - ms -

LGD recommend T16 Source 10 - ms -

T8 Source - - ms
Min 200ms T17 Source 0 - ms -
T9 Source - - ms - T18 Source 0 - ms -
Note) 1. Do not insert the mating cable when system turn on.
2. Valid Data have to meet “3-3. eDP Signal Timing Specifications”
3. Video Signal, LED_EN and PWM need to be on pull-down condition on invalid status.
4. LGD recommend the rising sequence of VLED after the Vcc and valid status of Video Signal turn on.
Ver. 0.1 May. 10, 2013 12 / 34
 LP156WH3
Liquid Crystal Display
Product Specification

4. Optical Specification
Optical characteristics are determined after the unit has been ‘ON’ and stable for approximately 30 minutes in
a dark environment at 25C. The values specified are at an approximate distance 50cm from the LCD surface
at a viewing angle of  and  equal to 0.
FIG. 1 presents additional information concerning the measurement equipment and method.

.tw
FIG. 1 Optical Characteristic Measurement Equipment and Method

LCD Module Pritchard 880 or

Optical Stage(x,y)
equivalent

om 50cm
d.c Table 9. OPTICAL CHARACTERISTICS

Ta=25C, VCC=3.3V, fV=60Hz, fCLK= 76.3MHz

Values
Parameter Symbol Units Notes
Min Typ Max
slc
Contrast Ratio CR 400 500 - 1
Surface Luminance, white LWH 170 200 - cd/m2 2
Luminance Variation  WHITE - 1.4 1.6 3
Response Time TrR+ TrD - 16 25 ms 4
w.y

Color Coordinates
RED RX 0.548 0.578 0.608
RY 0.314 0.344 0.374
GREEN GX 0.307 0.337 0.367
GY 0.541 0.571 0.601
BLUE BX 0.129 0.159 0.189
ww

BY 0.090 0.120 0.150

WHITE WX 0.283 0.313 0.343
WY 0.299 0.329 0.359
Viewing Angle 5
x axis, right(=0) r 40 - - degree
x axis, left (=180) l 40 - - degree
y axis, up (=90) u 10 - - degree
y axis, down (=270) d 30 - - degree
Gray Scale 6

Ver. 0.1 May. 10, 2013 13 / 34

 LP156WH3
Liquid Crystal Display
Product Specification

Note)
1. Contrast Ratio(CR) is defined mathematically as

Surface Luminance with all white pixels

Contrast Ratio =
Surface Luminance with all black pixels

.tw
2. Surface luminance is the average of 5 point across the LCD surface 50cm from the surface with
all pixels displaying white. For more information see FIG 1.

LWH = Average(L1,L2, … L5)

om
3. The variation in surface luminance , The panel total variation ( WHITE) is determined by measuring LN
at each test position 1 through 13 and then defined as following numerical formula.
For more information see FIG 2.

Maximum (L1,L2, … L13) Maximum(L1,L2, … L5)

 WHITE (13P) =  WHITE (5P) =
Minimum (L1,L2, … L13) Minimum(L1,L2, … L5)
d.c
4. Response time is the time required for the display to transition from white to black (rise time, TrR) and
from black to white(Decay Time, TrD). For additional information see FIG 3.

5. Viewing angle is the angle at which the contrast ratio is greater than 10. The angles are determined
slc
for the horizontal or x axis and the vertical or y axis with respect to the z axis which is normal to the
LCD surface. For more information see FIG 4.

6. Gray scale specification * fV = 60Hz

w.y

Gray Level Luminance [%] (Typ)

L0 0.15
L7 1.24
L15 4.97
L23 11.4
ww

L31 20.6
L39 34.4
L47 53.0
L55 75.7
L63 100

Ver. 0.1 May. 10, 2013 14 / 34

 LP156WH3
Liquid Crystal Display
Product Specification

FIG. 2 Luminance
<Measuring point for Average Luminance & measuring point for Luminance variation>
H

10mm A

.tw
6 7 8 10mm
2 3
B H,V : ACTIVE AREA
V A : H/4 mm
9 1 10
B : V/4 mm

om
POINTS: 13 POINTS
4 5 13
11 12

FIG. 3 Response Time Active Area

The response time is defined as the following figure and shall be measured by switching the input signal
for “black” and “white”.
d.c TrR TrD
%
100
slc
90

Optical
Response
10
0
w.y

white white
black

FIG. 4 Viewing angle Normal

Eye Y
<Dimension of viewing angle range>  = 90 , Up
ww

 = 180 ,
Left 

 = 0 ,
Right

 = 270 ,
Down

Ver. 0.1 May. 10, 2013 15 / 34

 LP156WH3
Liquid Crystal Display
Product Specification

5. Mechanical Characteristics
The contents provide general mechanical characteristics for the model LP156WH3. In addition the figures
in the next page are detailed mechanical drawing of the LCD.

Horizontal 359.5  0.5mm

.tw
Outline Dimension Vertical 217.2  0.5mm

Thickness 3.8mm (max)

Horizontal 347.5  0.5mm

Bezel Area

om
Vertical 196.8  0.5mm

Horizontal 344.23 mm
Active Display Area
Vertical 193.54 mm

Weight 400g (Max.)

d.c Surface Treatment Glare treatment of the front polarizer
slc
w.y
ww

Ver. 0.1 May. 10, 2013 16 / 34

 LP156WH3
Liquid Crystal Display
Product Specification

<FRONT VIEW> Note) Unit:[mm], General tolerance:  0.5mm

.tw
om
d.c
slc
w.y
ww

Ver. 0.1 May. 10, 2013 17 / 34

 LP156WH3
Liquid Crystal Display
Product Specification

<REAR VIEW> Note) Unit:[mm], General tolerance:  0.5mm

.tw
om
d.c
slc
w.y
ww

Ver. 0.1 May. 10, 2013 18 / 34

 LP156WH3
Liquid Crystal Display
Product Specification

LGD Proposal for system cover design.(Appendix)

Gap check for securing the enough gap between LCM and System
1
back cover.

.tw
LCM a b

PAD
Back cover

om
Boss

◆ a : min 0mm
Boss ◆ b : min 0.3mm, Max 1.0mm

PAD
d.c Back cover
slc
1.Rear side of LCM is sensitive against external stress, and previous check
about interference is highly needed.
Define 2.In case there is something from system cover comes into the boundary
above,mechanical interference may cause the FOS defects.
w.y

(Eg: Ripple, White spot..)

Check if antenna cable is sufficiently apart from T-CON of LCD
2
Module.
ww

T-CON T-CON

OK NG

Define 1.If system antenna is overlapped with T-CON,it might be cause the noise

Ver. 0.1 May. 10, 2013 19 / 34

 LP156WH3
Liquid Crystal Display
Product Specification

LGD Proposal for system cover design.(Appendix)

3 Checking the path of the System wire

Wire

.tw
om
NG OK

1.If Wire path overlapped with LCM, it is happened white spot,

COF problem, etc.
d.c
Define
2.OK  Wire path design to system side.
NG  Wire path overlapped with LCM.
4 Add pad to Prevent panel crack against external load (push)
slc
Pad Back cover flange
w.y

LCM
boss
Boss PAD
Back cover
ww

push push

Pad boss
boss boss
boss
crack
Back cover Back cover

OK NG

1. At flat type LCM, panel is easily cracked at flange area during push,
Define assemble.
2. Add pad, it prevent panel crack

Ver. 0.1 May. 10, 2013 20 / 34

 LP156WH3
Liquid Crystal Display
Product Specification

LGD Proposal for system cover design.(Appendix)

5 Check the rib or Bracket on back cover

.tw
LCM LCM

Back cover Back cover

Rib Bracket
OK OK

om
LCM LCM

Back cover Back cover

NG CO
d.c
1.It is necessary that the height of back cover rib or bracket is higher than
Define LCM height. It can prevent direct compression of panel at LCM edge.
slc
2.”ㄱ” shape bracket is stronger than “I” shape one.
6 Check the gap between front cover and LCM(glass)
w.y

a
Front cover

LCM
ww

Back cover

[OK] a ≥ 0.3mm
[CO] 0.3mm ≥ a ≥ 0.1mm
[NG] a ≤ 0.1mm

Define 1. Ripple can be happened by little gap between glass and front cover.

Ver. 0.1 May. 10, 2013 21 / 34

 LP156WH3
Liquid Crystal Display
Product Specification

LGD Proposal for system cover design.(Appendix)

7 Check the rib or Bracket on back cover

.tw
Light leakage
Front cover Front cover

LCM LCM

Back cover Back cover

om
OK NG

1.If it is possible, shrink to apply front cover of white color.

d.c
Define
2. White color can caused light leakage
8 Check the wire position(path)
slc
w.y

Back cover

OK
ww

Back cover

NG

1. It is necessary that wire is posited out of hook, not posited near hook,.
Define 2. If wire is posited near hook, it can be happened assemble error and
panel crack during assemble front cover

Ver. 0.1 May. 10, 2013 22 / 34

 LP156WH3
Liquid Crystal Display
Product Specification

LGD Proposal for system cover design.(Appendix)

9 Check mouse pad (touch pad) depth and shape of edge

a
[OK] a ≤ 0.3mm
[CO] 0.5mm ≥ a ≥ 0.3mm

.tw
[NG] a ≥ 0.5mm

om
Mouse pad

OK NG
d.c
Define
1.Mouse pad step is deep, it is caused panel crack by external load.
2. The edge shape must be smooth.
10 Check the step of keyboard area
slc
Keyboard Keyboard
w.y
ww

push push

crack

OK NG

1. The step of keyboard at the side edge of main body, it is caused panel
Define
crack

Ver. 0.1 May. 10, 2013 23 / 34

 LP156WH3
Liquid Crystal Display
Product Specification

6. Reliability

Environment test condition

No. Test Item Conditions

.tw
1 High temperature storage test Ta= 60C, 240h
2 Low temperature storage test Ta= -20C, 240h
3 High temperature operation test Ta= 50C, 50%RH, 240h
4 Low temperature operation test Ta= 0C, 240h

om
5 Vibration test (non-operating) Sine wave, 5 ~ 150Hz, 1.5G, 0.37oct/min
3 axis, 30min/axis
6 Shock test (non-operating) - No functional or cosmetic defects following a shock
to all 6 sides delivering at least 180 G in a half sine
pulse no longer than 2 ms to the display module
d.c - No functional defects following a shock delivering
at least 200 g in a half sine pulse no longer than 2
ms to each of 6 sides. Each of the 6 sides will be
shock tested with one each display, for a total of 6
displays
7 Altitude operating 0 ~ 10,000 feet (3,048m) 24Hr
slc
storage / shipment 0 ~ 40,000 feet (12,192m) 24Hr

{ Result Evaluation Criteria }

There should be no change which might affect the practical display function when the display quality
test is conducted under normal operating condition.
w.y
ww

Ver. 0.1 May. 10, 2013 24 / 34

 LP156WH3
Liquid Crystal Display
Product Specification

7. International Standards
7-1. Safety
a) UL 60950-1, Second Edition, Underwriters Laboratories Inc.
Information Technology Equipment - Safety - Part 1 : General Requirements.

.tw
b) CAN/CSA C22.2 No.60950-1-07, Second Edition, Canadian Standards Association.
Information Technology Equipment - Safety - Part 1 : General Requirements.
c) EN 60950-1:2006 + A11:2009, European Committee for Electrotechnical Standardization (CENELEC).
Information Technology Equipment - Safety - Part 1 : General Requirements.
d) IEC 60950-1:2005, Second Edition, The International Electrotechnical Commission (IEC).
Information Technology Equipment - Safety - Part 1 : General Requirements.

om
7-2. EMC

a) ANSI C63.4 “American National Standard for Methods of Measurement of Radio-Noise

d.c
Emissions from Low-Voltage Electrical and Electronic Equipment in the Range of 9 kHz to 40 GHz.”
American National Standards Institute (ANSI), 2003.
b) CISPR 22 “Information technology equipment – Radio disturbance characteristics – Limit and
methods of measurement." International Special Committee on Radio Interference
(CISPR), 2005.
c) CISPR 13 “Sound and television broadcast receivers and associated equipment – Radio disturbance
slc
characteristics – Limits and method of measurement." International Special Committee on Radio
Interference (CISPR), 2006.

7-3. Environment
w.y

a) RoHS, Directive 2002/95/EC of the European Parliament and of the council of 27 January 2003
ww

Ver. 0.1 May. 10, 2013 25 / 34

 LP156WH3
Liquid Crystal Display
Product Specification

8. Packing

8-1. Designation of Lot Mark

a) Lot Mark

A B C D E F G H I J K L M

.tw
A,B,C : SIZE(INCH) D : YEAR
E : MONTH F ~ M : SERIAL NO.

om LGD Lot Mark

d.c
Note
1. YEAR
slc
Year 2011 2012 2013 2014 2015 2016 2017 2018 2019 2020

Mark A B C D E F G H J K
w.y

2. MONTH

Month Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec

Mark 1 2 3 4 5 6 7 8 9 A B C
ww

b) Location of Lot Mark

Serial No. is printed on the label. The label is attached to the backside of the LCD module.
This is subject to change without prior notice.

8-2. Packing Form

a) Package quantity in one box : 20pcs

b) Box Size : 478mm X 365mm X 328mm

Ver. 0.1 May. 10, 2013 26 / 34

 LP156WH3
Liquid Crystal Display
Product Specification

# APPENDIX-1

■ Box Label

.tw
om
d.c
■ Pallet Label
slc
w.y
ww

Ver. 0.1 May. 10, 2013 27 / 34

 LP156WH3
Liquid Crystal Display
Product Specification

# APPENDIX-2

■ Packing Assembly

.tw
④

om
1 LCM / 1 Bag

③ ①
d.c ②
2 LCM / 1 Slot

20LCM/Box = 10 Slot
slc
⑤

⑥
w.y

NO. DESCRIPTION MATERIAL

1 LCD Module
ww

2 BAG AL

3 TAPE MASKING 20MMX50M

4 PACKING, TOP EPS

5 PACKING, BOTTOM EPS

6 BOX SWR4

7 TAPE OPP 70MMX300M

8 LABEL ART 100X70

Ver. 0.1 May. 10, 2013 28 / 34

 LP156WH3
Liquid Crystal Display
Product Specification

# APPENDIX-3

■ Pallet Assembly

.tw
③
⑤

om
④

① ⑦

②
d.c
slc
w.y

NO. DESCRIPTION MATERIAL

ww

1 Packing AssY

2 Pallet Plywood

3 Angle Cover SWR4

4 Label ART 100X70

5 Band PP

6 Wrap LLDPE

7 CLIP Steel

Ver. 0.1 May. 10, 2013 29 / 34

 LP156WH3
Liquid Crystal Display
Product Specification

9. PRECAUTIONS

Please pay attention to the followings when you use this TFT LCD module.

9-1. MOUNTING PRECAUTIONS

.tw
(1) You must mount a module using holes arranged in four corners or four sides.
(2) You should consider the mounting structure so that uneven force (ex. Twisted stress) is not applied to
t h e
module. And the case on which a module is mounted should have sufficient strength so that external
force is not transmitted directly to the module.

om
(3) Please attach the surface transparent protective plate to the surface in order to protect the polarizer.
Transparent protective plate should have sufficient strength in order to the resist external force.
(4) You should adopt radiation structure to satisfy the temperature specification.
(5) Acetic acid type and chlorine type materials for the cover case are not desirable because the former
generates corrosive gas of attacking the polarizer at high temperature and the latter causes circuit break
by electro-chemical reaction.
(6) Do not touch, push or rub the exposed polarizers with glass, tweezers or anything harder than HB
d.c
pencil lead. And please do not rub with dust clothes with chemical treatment.
Do not touch the surface of polarizer for bare hand or greasy cloth.(Some cosmetics are detrimental
to the polarizer.)
(7) When the surface becomes dusty, please wipe gently with absorbent cotton or other soft materials like
chamois soaks with petroleum benzene. Normal-hexane is recommended for cleaning the adhesives
used to attach front / rear polarizers. Do not use acetone, toluene and alcohol because they cause
slc
chemical damage to the polarizer.
(8) Wipe off saliva or water drops as soon as possible. Their long time contact with polarizer causes
deformations and color fading.
(9) Do not open the case because inside circuits do not have sufficient strength.
(10) When handling the LCD module, it needs to handle with care not to give mechanical stress to the PCB
and Mounting Hole area.”
w.y

9-2. OPERATING PRECAUTIONS

(1) The spike noise causes the mis-operation of circuits. It should be lower than following voltage :
V=± 200mV(Over and under shoot voltage)

(2) Response time depends on the temperature.(In lower temperature, it becomes longer.)
ww

(3) Brightness depends on the temperature. (In lower temperature, it becomes lower.)
And in lower temperature, response time(required time that brightness is stable after turned on) becomes
longer.
(4) Be careful for condensation at sudden temperature change. Condensation makes damage to polarizer or
electrical contacted parts. And after fading condensation, smear or spot will occur.
(5) When fixed patterns are displayed for a long time, remnant image is likely to occur.
(6) Module has high frequency circuits. Sufficient suppression to the electromagnetic interference shall be
done by system manufacturers. Grounding and shielding methods may be important to minimized the
interference.

Ver. 0.1 May. 10, 2013 30 / 34

 LP156WH3
Liquid Crystal Display
Product Specification

9-3. ELECTROSTATIC DISCHARGE CONTROL

Since a module is composed of electronic circuits, it is not strong to electrostatic discharge. Make certain that
treatment persons are connected to ground through wrist band etc. And don’t touch interface pin directly.

.tw
9-4. PRECAUTIONS FOR STRONG LIGHT EXPOSURE
Strong light exposure causes degradation of polarizer and color filter.

9-5. STORAGE

om
When storing modules as spares for a long time, the following precautions are necessary.

(1) Store them in a dark place. Do not expose the module to sunlight or fluorescent light. Keep the
temperature between 5C and 35C at normal humidity.
(2) The polarizer surface should not come in contact with any other object.
It is recommended that they be stored in the container in which they were shipped.
d.c
9-6. HANDLING PRECAUTIONS FOR PROTECTION FILM
(1) When the protection film is peeled off, static electricity is generated between the film and polarizer.
This should be peeled off slowly and carefully by people who are electrically grounded and with well
ion-blown equipment or in such a condition, etc.
slc
(2) The protection film is attached to the polarizer with a small amount of glue. If some stress is applied
to rub the protection film against the polarizer during the time you peel off the film, the glue is apt to
remain on the polarizer.
Please carefully peel off the protection film without rubbing it against the polarizer.
(3) When the module with protection film attached is stored for a long time, sometimes there remains a
w.y

very small amount of glue still on the polarizer after the protection film is peeled off.
(4) You can remove the glue easily. When the glue remains on the polarizer surface or its vestige is
recognized, please wipe them off with absorbent cotton waste or other soft material like chamois
soaked with normal-hexane.
ww

Ver. 0.1 May. 10, 2013 31 / 34

 LP156WH3
Liquid Crystal Display
Product Specification

APPENDIX A. Enhanced Extended Display Identification Data (EEDIDTM) 1/3

Byte Byte Value Value
(Dec) (Hex) Field Name and Comments (Hex) (Bin)
0 00 Header 00 00000000
1 01 Header FF 11111111
2 02 Header FF 11111111
Header

3 03 Header FF 11111111
4 04 Header FF 11111111

.tw
5 05 Header FF 11111111
6 06 Header FF 11111111
7 07 Header 00 00000000
8 08 ID Manufacture Name LGD 30 00110000
9 09 ID Manufacture Name E4 11100100
10 0A ID Product Code 03F8h F8 11111000
Vendor / Product
EDID Version

11 0B ( Hex. LSB first ) 03 00000011

12 0C ID Serial No. - Optional ("00h" If not used, Number Only and LSB First) 00 00000000

om
13 0D ID Serial No. - Optional ("00h" If not used, Number Only and LSB First) 00 00000000
14 0E ID Serial No. - Optional ("00h" If not used, Number Only and LSB First) 00 00000000
15 0F ID Serial No. - Optional ("00h" If not used, Number Only and LSB First) 00 00000000
16 10 Week of Manufacture - Optinal 00 weeks 00 00000000
17 11 Year of Manufacture 2012 years 16 00010110
18 12 EDID structure version # = 1 01 00000001
19 13 EDID revision # = 4 04 00000100
Video input Definition = Input is a Digital Video signal Interface , Colo Bit Depth : 6 Bits per Primary Color ,
20 14
Digital Video Interface Standard Supported: DisplayPort is supported
95 10010101
d.c 21 15 Horizontal Screen Size (Rounded cm) = 35 cm 23 00100011
Parameters
Display

22 16 Vertical Screen Size (Rounded cm) = 19 cm 13 00010011

23 17 Display Transfer Characteristic (Gamma) = (gamma*100)-100 = Example:(2.2*100)-100=120 78 01111000
Feature Support [ Display Power Management(DPM) : Standby Mode is supported, Suspend Mode is not supported,
Active Off = Very Low Power is supported ,Supportted Color Encoding Formats : RGB 4:4:4 & YCrCb 4:4:4
24 18
,Other Feature Support Flags : No_sRGB, Preferred Timing Mode, No_Display is continuous frequency (Multi-
EA 11101010

mode_Base EDID and Extension Block).]

slc
25 19 Red/Green Low Bits (RxRy/GxGy) 05 00000101
26 1A Blue/White Low Bits (BxBy/WxWy) F5 11110101
27 1B Red X Rx = 0.578 94 10010100
Coordinates
Panel Color

28 1C Red Y Ry = 0.344 58 01011000

29 1D Green X Gx = 0.337 56 01010110
30 1E Green Y Gy = 0.571 92 10010010
31 1F Blue X Bx = 0.159 28 00101000
w.y

32 20 Blue Y By = 0.120 1E 00011110

33 21 White X Wx = 0.313 50 01010000
34 22 White Y Wy = 0.329 54 01010100
Established

35 23 Established timing 1 ( Optional_00h if not used) 00 00000000

Timings

36 24 Established timing 2 ( Optional_00h if not used) 00 00000000

37 25 Manufacturer's timings ( Optional_00h if not used) 00 00000000

ww

38 26 Standard timing ID1 ( Optional_01h if not used) 01 00000001

39 27 Standard timing ID1 ( Optional_01h if not used) 01 00000001
40 28 Standard timing ID2 ( Optional_01h if not used) 01 00000001
41 29 Standard timing ID2 ( Optional_01h if not used) 01 00000001
Standard Timing ID

42 2A Standard timing ID3 ( Optional_01h if not used) 01 00000001

43 2B Standard timing ID3 ( Optional_01h if not used) 01 00000001
44 2C Standard timing ID4 ( Optional_01h if not used) 01 00000001
45 2D Standard timing ID4 ( Optional_01h if not used) 01 00000001
46 2E Standard timing ID5 ( Optional_01h if not used) 01 00000001
47 2F Standard timing ID5 ( Optional_01h if not used) 01 00000001
48 30 Standard timing ID6 ( Optional_01h if not used) 01 00000001
49 31 Standard timing ID6 ( Optional_01h if not used) 01 00000001
50 32 Standard timing ID7 ( Optional_01h if not used) 01 00000001
51 33 Standard timing ID7 ( Optional_01h if not used) 01 00000001
52 34 Standard timing ID8 ( Optional_01h if not used) 01 00000001
53 35 Standard timing ID8 ( Optional_01h if not used) 01 00000001

Ver. 0.1 May. 10, 2013 32 / 34

 LP156WH3
Liquid Crystal Display
Product Specification

APPENDIX A. Enhanced Extended Display Identification Data (EEDIDTM) 2/3

Byte Byte Value Value
(Dec) (Hex) Field Name and Comments (Hex) (Bin)
54 36 Pixel Clock/10,000 (LSB) 76.3 MHz @ 60 Hz CE 11001110
55 37 Pixel Clock/10,000 (MSB) 1D 00011101
56 38 Horizontal Active (HA) (lower 8 bits) 1366 pixels 56 01010110
57 39 Horizontal Blanking (HB) (lower 8 bits) 244 pixels F4 11110100

.tw
58 3A Horizontal Active (HA) / Horizontal Blanking (HB) (upper 4:4bits) 50 01010000
Timing Descriptor #1

59 3B Vertical Avtive (VA) 768 lines 00 00000000

60 3C Vertical Blanking (VB) (DE Blanking typ.for DE only panels) 22 lines 16 00010110
61 3D Vertical Active (VA) / Vertical Blanking (VB) (upper 4:4bits) 30 00110000
62 3E Horizontal Front Porch in pixels (HF) (lower 8 bits) 48 pixels 30 00110000
63 3F Horizontal Sync Pulse Width in pixels (HS) (lower 8 bits) 32 pixels 20 00100000
64 40 Vertical Front Porch in lines (VF) : Vertical Sync Pluse Width in lines (VS) (lower 4 bits) 3 lines : 5 lines 35 00110101

om
65 41 Horizontal Front Porch/ Sync Pulse Width/ Vertical Front Porch/ Sync Pulse Width (upper 2bits) 00 00000000
66 42 Horizontal Vedio Image Size (mm) (lower 8 bits) 345 mm 59 01011001
67 43 Vertical Vedio Image Size (mm) (lower 8 bits) 194 mm C2 11000010
68 44 Horizontal Image Size / Vertical Image Size (upper 4 bits) 10 00010000
69 45 Horizontal Border = 0 (Zero for Notebook LCD) 00 00000000
70 46 Vertical Border = 0 (Zero for Notebook LCD) 00 00000000
71 47 Non-Interlace, Normal display, no stereo, Digital Separate [ Vsync_NEG, Hsync_NEG (outside of V-sync) ] 19 00011001
72 48 Flag 00 00000000
d.c 73
74
75
49
4A
4B
Flag
Flag
Data Type Tag (Descriptor Defined by manufacturer )
00
00
00
00000000
00000000
00000000
76 4C Flag 00 00000000
Timing Descriptor #2

77 4D Descriptor Defined by manufacturer 00 00000000

78 4E Descriptor Defined by manufacturer 00 00000000
79 4F Descriptor Defined by manufacturer 00 00000000
slc
80 50 Descriptor Defined by manufacturer 00 00000000
81 51 Descriptor Defined by manufacturer 00 00000000
82 52 Descriptor Defined by manufacturer 00 00000000
83 53 Descriptor Defined by manufacturer 00 00000000
84 54 Descriptor Defined by manufacturer 00 00000000
85 55 Descriptor Defined by manufacturer 00 00000000
w.y

86 56 Descriptor Defined by manufacturer 00 00000000

87 57 Descriptor Defined by manufacturer 00 00000000
88 58 Descriptor Defined by manufacturer 00 00000000
89 59 Descriptor Defined by manufacturer 00 00000000
90 5A Flag 00 00000000
91 5B Flag 00 00000000
92 5C Flag 00 00000000
93 5D Data Type Tag ( Alphanumeric Data String (ASCII String) ) FE 11111110
ww

94 5E Flag 00 00000000
Timing Descriptor #3

95 5F Alphanumeric Data String (ASCII String) L 4C 01001100

96 60 Alphanumeric Data String (ASCII String) G 47 01000111
97 61 Alphanumeric Data String (ASCII String) 20 00100000
98 62 Alphanumeric Data String (ASCII String) D 44 01000100
99 63 Alphanumeric Data String (ASCII String) i 69 01101001
100 64 Alphanumeric Data String (ASCII String) s 73 01110011
101 65 Alphanumeric Data String (ASCII String) p 70 01110000
102 66 Alphanumeric Data String (ASCII String) l 6C 01101100
103 67 Alphanumeric Data String (ASCII String) a 61 01100001
104 68 Alphanumeric Data String (ASCII String) y 79 01111001
105 69 Manufacturer P/N(If<13 char--> 0Ah, then terminate with ASCⅡ code 0Ah,set remaining char = 20h) 0A 00001010
106 6A Manufacturer P/N(If<13 char--> 0Ah, then terminate with ASCⅡ code 0Ah,set remaining char = 20h) 20 00100000
107 6B Manufacturer P/N(If<13 char--> 0Ah, then terminate with ASCⅡ code 0Ah,set remaining char = 20h) 20 00100000

Ver. 0.1 May. 10, 2013 33 / 34

 LP156WH3
Liquid Crystal Display
Product Specification

APPENDIX A. Enhanced Extended Display Identification Data (EEDIDTM) 3/3

Byte Byte Value Value
(Dec) (Hex) Field Name and Comments (Hex) (Bin)
108 6C Flag 00 00000000
109 6D Flag 00 00000000
110 6E Flag 00 00000000
111 6F Data Type Tag ( Alphanumeric Data String (ASCII String) ) FE 11111110

.tw
112 70 Flag 00 00000000
Timing Descriptor #4

113 71 Alphanumeric Data String (ASCII String) L 4C 01001100

114 72 Alphanumeric Data String (ASCII String) P 50 01010000
115 73 Alphanumeric Data String (ASCII String) 1 31 00110001
116 74 Alphanumeric Data String (ASCII String) 5 35 00110101
117 75 Alphanumeric Data String (ASCII String) 6 36 00110110
118 76 Alphanumeric Data String (ASCII String) W 57 01010111

om
119 77 Alphanumeric Data String (ASCII String) H 48 01001000
120 78 Alphanumeric Data String (ASCII String) 3 33 00110011
121 79 Alphanumeric Data String (ASCII String) - 2D 00101101
122 7A Alphanumeric Data String (ASCII String) T 54 01010100
123 7B Alphanumeric Data String (ASCII String) P 50 01010000
124 7C Alphanumeric Data String (ASCII String) S 53 01010011
125 7D Alphanumeric Data String (ASCII String) 1 31 00110001
d.c
Checksum

126 7E Extension flag (# of optional 128 panel ID extension block to follow, Typ = 0) 00 00000000

127 7F Check Sum (The 1-byte sum of all 128 bytes in this panel ID block shall = 0) 25 00100101
slc
w.y
ww

Ver. 0.1 May. 10, 2013 34 / 34