Scribd
Upload
8 views4 pages

Can23 26

Uploaded by

philippeouellette88
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
8 views4 pages

Can23 26

Uploaded by

philippeouellette88
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

NILUS II 36”, 45” and 60”

Counter-balance
Nilus II 4s jack Nilus II Nilus II
4s folded

MODEL: JACK-TYPE
36” 1029-0000 4 Shaft Loom $3713.00
45” 1030-0000 4 Shaft Loom $3933.00 NILUS II
60” 1031-0000 4 Shaft Loom $4483.00 JACK TYPE 8s

MODEL: COUNTER-BALANCE
36” 1026-0000 4 Shaft Loom $3713.00
45” 1027-0000 4 Shaft Loom $3933.00
60” 1028-0000 4 Shaft Loom $4483.00

72” 1028-0072 4 Shaft Loom


With 2 set of treadles and 2 brake system: $6710.00
MODEL: 8 SHAFT JACK-TYPE
36” 1029-0008 8 Shaft Loom $4263.00
45” 1030-0008 8 Shaft Loom $4950.00
60” 1031-0008 8 Shaft Loom $5495.00

(Counter-balanced, Jack-type or Jack-type with back hinge treadles )


The Nilus II 4s is available in two versions- Jack or counterbalance. The 8s loom is available in 3 ver-
sions - Jack, Jack with Back Hinge Treadles and Countermarche. The Nilus II loom has been designed
with a stabilizer foot, for better stability. The shed is always good with any tie-up combination. The
counter-balanced version is built with an integrated shed regulator, so it is possible to weave any kind
of material. On the jack-type version, the top can be easily removed, allowing easy access to the shafts
for the addition or removal of heddles. Heddles used are 12½" (31.7 cm) long. It is a loom with indepen-
dent shafts, guided by pegs at each side, preventing friction of the frames which are pushed upwards
by an underneath mechanism. All Nilus II looms have non-sliding polyvinyl foot pads under the uprights
to keep it solid on the floor. It is equipped with a friction brake giving perfect tension every time. The
front cloth beam and back thread beam are removable for easy threading, and the warp beam is also
removeable for outside beaming when required. All looms are equipped with a regular plain beam to
which a set of rake-like pieces can be added to convert it into a sectional warp beam. Special kits have
been designed to convert the regular 4 shaft jack-type into an 8 shaft jack-type loom. A new back hinge
treadle kit is also available. Any Nilus II 8 shaft can be upgraded to a back hinge treadle loom.

See page 26 for Equipment, Dimensions and Options

CA 2023 23
NILUS II 36”, 45” and 60” JACK-TYPE
WITH BACK HINGE TREADLES
As with all Loom designs there are some trad-
eoffs. With the Jack Loom the problem most
often cited was the difficulty in getting a good
shed with 6+ Shaft weave construction. Our
new design has overcome this problem.

The new design features the Treadles anchored


at the rear of the Loom, with a new unique,
Rocker mechanism that insures even tension on
all Treadle Cords with the Treadles in both the
rest or depressed position.

This new design provides the weaver with the


ease of Leg Treadling multi Shaft designs, com-
parable to that of a 4 shaft.

In addition, a wide, clean shed is obtained on all


Shafts. Using a new procedure, the new Treadle
design retains the folding feature designed into
the original Nilus II.

We, at Leclerc, are very excited about this


new Jack Loom Treadling concept. This
system is also available on the Nilus and
Artisat loom.

8 SHAFT LOOM KIT 4 MORE BACK HINGE BACK HINGE


WITH BACK HINGE SHAFT WITH BACK TREADLES KIT FOR TREADLES KIT FOR
TREADLES HINGE TREADLES EXISTING NUII 8S EXISTING NUII 4S

36” 1029-3628 $4807.00 1029-2836 $2723.00 1029-3036 $1128.00 1029-4036 $908.00


45” 1030-4528 $5176.00 1030-2845 $3102.00 1030-3045 $1227.00 1030-4045 $1007.00
60” 1031-6028 $5885.00 1031-2860 $3685.00 1031-3060 $1337.00 1031-4060 $1056.00

See page 26 for Equipment, Dimensions and Options

CA 2023 24
NILUS II 36”, 45” and 60”
COUNTERMARCHE BACK HINGE TREADLES
Our countermarche system has only one set of lams,
two sets of pulleys above the shafts and one set of pul-
leys below. In a countermarche loom, every shaft is
actively involved in each shed: each shaft is either lifted
or pulled down by each pedal. Uneven sheds like 3
shafts against 1 are always large and clean .Because
you actually lift or pull down every shaft, you never have
any problem with one shaft floating when it should not.
More details are in our technical report page 4.

TIE-UP SYSTEM
WITH LOOP CORD
(EASY AND FAST)

PRE-ADJUSTED
CABLES,
NO ADJUSTMENT
TO DO.

NILUS II 8S COUNTERMARCHE LOOM BACK HINGE TREADLES


36” 1029-0018 $5720.00
45” 1030-0018 $6122.00
60” 1031-0018 $7029.00

See page 26 for Equipment, Dimensions and Options

CA 2023 25
NILUS II (INFORMATION FOR ALL 4 MODELS)
STANDARD EQUIPMENT
» 6 treadles » 2 lease sticks
» Stainless Steel Reed, 12 dents/inch » 4 warp rods
» Wire heddles, 12½" (31,7 cm) » 2 cords
» 1 boat shuttle 11¾" 6122-3000 » 2 aprons
» 1 doz. plastic bobbins 6133-6000 » Book: "Warp and Weave"
» 1 reed & heddle hook 6141-7000 » Assembly instructions and Video

SPECIFICATIONS & DIMENSIONS


Weaving width 36” (90 cm) 45” 115 cm 60” 150 cm
Quantity of heddles (4 or 8s) 1000 1200 1500
Depth opened 4s = 48” 122 cm 8s = 51” 129 cm
Depth closed 4s = 27½” 70 cm 8s = 32” 81 cm
Loom width 46” (117 cm) 55” 140 cm 70” 170 cm
Total Height Jack = 49” 125 cm Counter-Balance = 58½” 149 cm
Front height 34½” 87 cm
Distance between the reed and breastbeam 13” 33cm

Net weight 4s =155 lbs 70 kg 4s = 150 lbs 68 kg 4s = 170 lbs 77 kg


8s= 190 lbs 86 kg 8s = 205 lbs 93 kg 8s = 250 lbs 113 kg

OPTIONS:
Weaving width 36” 90 cm 45” 115 cm 60” 150 cm
Extra charge for inserted eye (or tex-
1029-9836 $114.00 1030-9845 $130.00 1031-9860 $172.00
solv) heddles instead of wire heddles
Bench with open ends 26'' 6384-4000 $788.00
Sectional warp beam 1” sections 6441-4000 $314.00 6441-5000 $384.00 6441-6000 $484.00
Sectional warp beam 2” sections 6442-4000 $265.00 6442-5000 $294.00 6442-6000 $386.00
Double back beam 6432-3000 $677.00 6432-4000 $775.00 6430-6000 $898.00
Flying shuttle beater 6471-4000 $1380.00 6471-5000 $1380.00 6471-6000 $1495.00

Kit to transform a 4 shaft Nilus loom to


1029-2836 $2723.00 1030-2845 $3102.00 1031-2860 $3685.00
an 8 shaft with back hinge treadles

CA 2023 26

You might also like