Government Polytechnic Beed

Micro-project Proposal

Develop solid models of individual components press tool

assembly using Proe /Creo software

1.0 Aim/ benefits of micro-project:-

To develop solid models of components press tool
To assemble the press tool

Course Outcome Addressed:-

1.Generate 3D solid models from 2D sketches using part workbench
of any parametric CAD software.
2. Prepare assembly of model using assembly workbench of any
parametric CAD Software

2.0 Proposed methodology:-

1. Firstly, we selected the given micro project after discussion and guidance
of teacher.
2. Collect the drawing of PRESSTOOL
3. Collect information of different commands used in Proe software.
4. Draw and develop the bottom plate in part work bench.
5. Draw and develop the top plate in part work bench.
6. Draw and develop the guide pillar in part work bench.
7. Draw and develop the guide bush in part work bench.
8. Assemble the press tool in Assembly Work bench.
9. Correct the Errors if any .
Compline this information in given format and submit it.
Government Polytechnic Beed

• Rationale Solid modeling is the most advanced method of geometric

modeling in three dimensions. The main purpose of engineering
drawing is to communicate to other Engineers, Machinists, etc. To
create a 3D feature assemblies of relative Components. Just as you
can combine feature into parts, you can also combine parts into
assemblies. Any Modeling parametric CAD software enables you to
place components parts and subassemblies together to form
assemblies.

• Aim of Micro Project

To develop solid models of components press tool.

To assemble the press tool.

• Course Outcome Addressed:-

1.Generate 3D solid models from 2D sketches using part workbench
of any parametric CAD software.
2. Prepare assembly of model using assembly workbench of any
parametric CAD Software.

• Literature Review

Different You Tube videos

https://youtu.be/ZkPMYen0jSQ?si=jHH9MIvBmv6fdzv2

https://youtu.be/nbhQTShOS0o?si=WVpyUX-czAlsQevC
https://youtu.be/riSbtpyZdiM?si=UEI45gB2IKXYVtfT

Book :- Parametric Solid Modeling Projects - Authors : Sham Tickko

Government Polytechnic Beed

Actual Methodology Followed

First of all open the software then set Working directory and Create a New
part file utilizing the default templet and entre and enter the name of the
Model “PRESSTOOL”

Step No : 01 Once open the Proe Software, go to upper left corner and click
the sheet of paper to create a new document.
1. Click on Part then OK
2. In our design we are going to use MMNS-PART SOLID unit system, so
in order to do that; select options icons on the toolbar
3. Click on Document Properties tab.
4. In the left menu, select “Units”.
5. In the unit system bar, choose “MMNS-PART SOLID”.
6. Click OK
Government Polytechnic Beed

Step No : 02

Select the “FRONT” plan to draw the BOTTOM PLATE.

Government Polytechnic Beed

Use the rectangle command to draw rectangle in front plane and give dimensions
250X150mm

Step N0 : 03

After, given the dimension Extrude the part by EXTRUDE Command. Then
use extrude on both side of sketch plane by half specified depth value in
each direction by 30 then click on done

Step N0 : 04
Government Polytechnic Beed

And click to the sketch front plane and draw the four circle
diameter of 25mm after that use extrude command and use
remove material

Step N0 : 5

Now select sketch and select the top plane and draw the another circle
which diameter is 50mm then use extrude command and remove material
Government Polytechnic Beed

Step N0 : 6
Government Polytechnic Beed

Once open the Proe Software, go to upper left corner and click the sheet of
paper to create a new document.
1. Click on Part then OK
2. In our design we are going to use MMNS-PART SOLID unit system, so
in order to do that; select options icons on the toolbar
3. Click on Document Properties tab.
4. In the left menu, select “Units”.
5. In the unit system bar, choose “MMNS-PART SOLID”.
6. Click OK

Step N0 : 7
Government Polytechnic Beed

Select the TOP PLANE and draw the Top Plate

Government Polytechnic Beed

draw the four circle diameter of 40mm after that use extrude command and
use remove material draw another circle which is diameter is 50 mm and
extrude it and give height 90mm

step no 8

Once open the Proe Software, go to upper left corner and click the sheet of
paper to create a new document.
1. Click on Part then OK
2. In our design we are going to use MMNS-PART SOLID unit system, so
in order to do that; select options icons on the toolbar
3. Click on Document Properties tab.
4. In the left menu, select “Units”.
5. In the unit system bar, choose “MMNS-PART SOLID”.
6. Click OK

Select the TOP PLANE and draw the Guide pillar diameter of 25 mm
Government Polytechnic Beed
Government Polytechnic Beed

After, given the dimension Extrude the part by EXTRUDE Command. Then
use extrude on both side of sketch plane by half specified depth value in
each direction by 200 then click on done

Step no 9

After that use round command and round the top and bottom circle by
entering valve 2
Government Polytechnic Beed

Step 10

Once open the Proe Software, go to upper left corner and click the sheet of
paper to create a new document.
1. Click on Part then OK
2. In our design we are going to use MMNS-PART SOLID unit system, so
in order to do that; select options icons on the toolbar
3. Click on Document Properties tab.
4. In the left menu, select “Units”.
5. In the unit system bar, choose “MMNS-PART SOLID”.
6. Click OK
Government Polytechnic Beed
Government Polytechnic Beed
Government Polytechnic Beed

Select the TOP PLANE and draw the Guide bush’s inner diameter and outer
diameter of 25mmand 40mm after that After, given the dimension Extrude
the part by EXTRUDE Command. Then use extrude on both side of sketch
plane by half specified depth value in each direction by 60 then click on
done .after this select the edge chamfer .sets the dimensioning scheme for
chamfer is Angel x D. angle is 45 and diameter is 2. Do the edge chamfer on
bottom and top of bush.

Step No : 11

To assembly the PRESS_TOOL, Create new file and set the Working
Directory. Then utilizing the default template and entre and enter the name
Government Polytechnic Beed

of the Model ASSEMBLY_OF_ PRESS_TOOL Select the Assembly option

….. 1. Click on Part then OK
2. In our design we are going to use MMNS PART SOLID unit system, so
in order to do that; select options icons on the toolbar
3. Click on Document Properties tab.
4. In the left menu, select “Units”.
5. In the unit system bar, choose “MMNS_ASM_DESIGN”.
6. Click OK

Step 12
Government Polytechnic Beed

First, we will place the bottom plate part in the assembly and assemble it at
default location
Government Polytechnic Beed

After taking bottom plate take bush pillar and use coincident command
which is in component placement.do the same with remaining bush pillar
after coincident four pillars in bottom plate it look like this
 Government Polytechnic Beed

Take guide bush part in the assembly and

assemble it at default location now coincident
the axis guide bush and guide pillar
Government Polytechnic Beed

After the coincident press on bottom of guide pillar and guide bush choose
the distance command from component parameters and give length 20
Government Polytechnic Beed

Take top plate part in the assembly and assemble it at default location now
coincident the axis of guide bush and guide pillar then it will look like

here the assembly is finish

Government Polytechnic Beed

Sr Name of Resources Specification

.
no
1 YouTube/ Goggle To See the Different Videos, Websites and
PDF‟S with Related to

2 Solid Modelling Software Pro Engineer Wild fire 5.0

3 Computer i5 Generation RAM – 4GB

4 Different Book https://youtu.be/ZkPMYen0jSQ?si=j

HH9MIvBmv6fdzv2

https://youtu.be/nbhQTShOS0o?si=
WVpyUX-czAlsQevC
https://youtu.be/riSbtpyZdiM?si=UEI
45gB2IKXYVtfT

Book :- Parametric Solid Modeling

Projects - Authors : Sham Tickko
Government Polytechnic Beed

Outputs of Micro Project

We understood various sketchers commands
We understood on part work bench
We understood assembly command

Skill Development
1. Drawing the 2D drawing in Proe Software
2. Drawing and develop 3D components in Proe Software
3. Assembling the Components in Assembling Workbench
4. Placing components in assembly.
5. Applying component references to fully constrained components

Application of Micro Project

Solid modeling is used not only for creating solid models of machine parts,
but also the buildings, electric circuits and even of the human beings. The
solid modeling software are being used for a large variety of applications,
here are some of them:

Engineering: The engineering design professionals use solid modeling to

see how the designed product will actually look like. The architects and civil
engineers use it to use the layout of the designed building.