Nissan-Versa 2015 en US Manual de Taller Desempanador d9c0417284
Nissan-Versa 2015 en US Manual de Taller Desempanador d9c0417284
E
CONTENTS
PRECAUTION ............................................... 3 WIRING DIAGRAM ...................................... 11 F
cardiagn.com
Precaution for Supplemental Restraint System Wiring Diagram ........................................................11 G
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" ................................................................... 3 BASIC INSPECTION ................................... 16
cardiagn.com
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along C
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted. D
Information necessary to service the system safely is included in the SR and SB section of this Service Man-
ual.
WARNING: E
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
F
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
cardiagn.com
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this G
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS H
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a I
hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the J
battery and wait at least three minutes before performing any service.
DEF
cardiagn.com
AWLIA2430ZZ
1. BCM (view with instrument panel re- 2. Rear window defogger relay (view 3. Front air control (rear window defog-
moved) with instrument panel removed) ger switch)
4. Door mirror (door mirror defogger) (if 5. Rear window defogger power con- 6. Rear window defogger ground con-
equipped) nector nector
• Operates the rear window defogger with the operation of rear window defogger switch.
BCM
• Performs the timer control of rear window defogger.
Rear window defogger relay • Operates the rear window defogger and the door mirror defogger* with the control signal from
BCM.
Front air control (rear window • The rear window defogger switch is turned ON.
defogger switch) • Turns the indicator lamp ON when detecting the operation of rear window defogger.
• Heats the heating wire with the power supply from the rear window defogger relay to prevent
Rear window defogger
the rear window from fogging up.
• Heats the heating wire with the power supply from the rear window defogger relay to prevent
Door mirror defogger* the door mirror from fogging up.
*: With heated mirrors
cardiagn.com
ALLIA1028GB
G
H
Operation Description
• When rear window defogger switch is turned ON while ignition switch is ON, the front air control (rear win-
dow defogger switch) transmits rear window defogger switch signal to BCM.
• BCM turns rear window defogger relay ON when rear window defogger switch signal is received. I
• Rear window defogger and door mirror defogger (with door mirror defogger) are supplied with power and
operate when rear window defogger relay turns ON.
• Rear window defogger ON is displayed when front air control receives signals. J
Timer function
• BCM turns rear window defogger relay ON for approximately 15 minutes when rear window defogger switch
is turned ON while ignition switch is ON. It makes rear window defogger and door mirror defogger (with door K
mirror defogger) operate.
• Timer is canceled after pressing rear window defogger switch again during timer operation. Then BCM turns
rear window defogger relay OFF. The same reaction also occurs during timer operation, if the ignition switch DEF
is turned OFF.
APPLICATION ITEM
CONSULT performs the following functions via CAN communication with BCM.
SYSTEM APPLICATION
cardiagn.com
BCM can perform the following functions.
Configuration
Work support
Data Monitor
Active Test
DATA MONITOR B
ACTIVE TEST D
cardiagn.com
G
DEF
APPLICATION ITEM
CONSULT performs the following functions via CAN communication with BCM.
SYSTEM APPLICATION
cardiagn.com
BCM can perform the following functions.
Configuration
Work support
Data Monitor
Active Test
DATA MONITOR B
ACTIVE TEST
E
Test Item Description
REAR DEFOGGER This test is able to check rear window defogger operation [Off/On].
F
cardiagn.com
G
DEF
ECU Reference
BCS-29, "Reference Value"
BCS-46, "Fail-safe"
BCM (with Intelligent Key system)
BCS-48, "DTC Inspection Priority Chart"
BCS-49, "DTC Index"
BCS-101, "Reference Value"
BCS-112, "Fail-safe"
BCM (without Intelligent Key system)
BCS-112, "DTC Inspection Priority Chart"
BCS-113, "DTC Index"
cardiagn.com
cardiagn.com
G
DEF
AALWA0906GB
cardiagn.com
AALIA2681GB
cardiagn.com
G
DEF
AALIA2682GB
cardiagn.com
AALIA2683GB
cardiagn.com
G
DEF
AALIA2684GB
OVERALL SEQUENCE
cardiagn.com
JMKIA0101GB
DETAILED FLOW
cardiagn.com
Connect CONSULT to the vehicle in “DATA MONITOR” mode and check real time diagnosis results. G
Verify relation between the symptom and the condition when the symptom is detected.
>> GO TO 5. H
>> GO TO 8.
Revision: March 2017 DEF-17 2015 Versa Sedan
DIAGNOSIS AND REPAIR WORK FLOW
< BASIC INSPECTION >
8. DETECT MALFUNCTIONING PART BY DIAGNOSTIC PROCEDURE
Inspect according to Diagnostic Procedure of the system.
NOTE:
The Diagnostic Procedure described based on open circuit inspection. A short circuit inspection is also
required for the circuit check in the Diagnostic Procedure.
Is malfunctioning part detected?
YES >> GO TO 9.
NO >> Check voltage of related BCM terminals using CONSULT.
9. REPAIR OR REPLACE THE MALFUNCTIONING PART
1. Repair or replace the malfunctioning part.
2. Reconnect parts or connectors disconnected during Diagnostic Procedure again after repair and replace-
ment.
3. Check DTC. If DTC is displayed, erase it.
>> GO TO 10.
10. FINAL CHECK
When DTC was detected in step 2, perform DTC Confirmation Procedure or Component Function Check
again, and then check that the malfunction have been repaired securely.
cardiagn.com
When symptom was described from the customer, refer to confirmed symptom in step 3 or 4, and check that
the symptom is not detected.
Does the symptom reappear?
YES (DTC is detected)>>GO TO 8.
YES (Symptom remains)>>GO TO 6.
NO >> Inspection End.
cardiagn.com
G
Monitored Item Condition Status
Rear DEF switch ON (LED ON) On H
REAR DEF SW
Rear DEF switch OFF (LED OFF) Off
Is the inspection result normal?
YES >> Inspection End. I
NO >> Refer to DEF-19, "Diagnosis Procedure".
Diagnosis Procedure INFOID:0000000010294851
J
BCM
Continuity
Connector Terminal
Ground
M18 (without Intelligent Key system) 10
No
M97 (with Intelligent Key system) 15
Is the inspection result normal?
YES >> Replace BCM. Refer to BCS-73, "Removal and Installation" (with Intelligent Key system) or BCS-
134, "Removal and Installation" (without Intelligent Key system).
NO >> Repair or replace harness.
3.CHECK GROUND CIRCUIT
Check continuity between front air control harness connector and ground.
cardiagn.com
Front air control
Continuity
Connector Terminal Ground
M33 8 Yes
Is the inspection result normal?
YES >> GO TO 4.
NO >> Repair or replace harness.
4.CHECK REAR WINDOW DEFOGGER SWITCH
Refer to DEF-20, "Component Inspection".
Is the inspection result normal?
YES >> Check intermittent incident. Refer to GI-41, "Intermittent Incident".
NO >> Replace front air control. Refer to HAC-46, "Removal and Installation".
Component Inspection INFOID:0000000010294852
1.CHECK FUNCTION C
1. Turn ignition switch ON.
2. Check that an operation noise of rear window defogger relay can be heard when turning the rear window
defogger switch ON. D
Is the inspection result normal?
YES >> Rear window defogger relay function is OK.
NO >> Refer to DEF-21, "Diagnosis Procedure" E
cardiagn.com
G
1.CHECK REAR WINDOW DEFOGGER RELAY POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF and disconnect rear window defogger relay connector. H
2. Turn ignition switch ON.
3. Check voltage between rear window defogger relay harness connector and ground.
I
(+)
Voltage (V)
Rear window defogger relay (−)
(Approx.)
Connector Terminal J
M14 2 Ground Battery voltage
Is the inspection result normal?
K
YES >> GO TO 3.
NO >> GO TO 2.
2.CHECK FUSE DEF
1. Turn ignition switch OFF.
2. Check 10A fuse (No. 5).
Is the inspection result normal? M
YES >> Check ignition power supply circuit. Refer to PG-26, "Wiring Diagram — Ignition Power Supply —
".
NO >> If fuse is blown, be sure to eliminate cause of malfunction before installing new fuse. N
3.CHECK REAR WINDOW DEFOGGER RELAY CONTROL CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BCM connector. O
3. Check continuity between BCM harness connector and rear window defogger relay harness connector.
BCM
Continuity
Connector Terminal
Ground
M20 (without Intelligent Key system) 64
No
M97 (with Intelligent Key system) 1
Is the inspection result normal?
YES >> GO TO 4.
NO >> Repair or replace harness.
4.CHECK REAR WINDOW DEFOGGER RELAY
Refer to DEF-22, "Component Inspection".
Is the inspection result normal?
YES >> Replace BCM. Refer to BCS-73, "Removal and Installation" (with Intelligent Key system) or BCS-
134, "Removal and Installation" (without Intelligent Key system).
NO >> Replace rear window defogger relay.
Component Inspection INFOID:0000000010294856
cardiagn.com
Check continuity between terminal 3 and 5, 6 and 7.
SEF745U
Heats the heating wire with the power supply from the rear window defogger relay to prevent the rear window B
from fogging up.
Component Function Check INFOID:0000000010294858
cardiagn.com
Regarding Wiring Diagram information, refer to DEF-11, "Wiring Diagram". G
1. CHECK FUSES H
Check if any of the following fuses in fuse block (J/B) are blown.
Terminals
(+) Condition of rear window de- Voltage (V) M
(–) fogger switch (Approx.)
Rear window defogger relay
Terminal
connector
ON Battery voltage N
M14 3, 6 Ground
OFF 0
Is the inspection result normal?
O
YES >> GO TO 3.
NO >> Check the following:
• Rear window defogger relay.
• Battery power supply circuit. P
3. CHECK POWER SUPPLY CIRCUIT
1. Turn ignition switch ON.
2. Check voltage between rear window defogger connector and ground.
Terminals
(+) Condition of rear window Voltage (V)
(–) defogger switch (Approx.)
Rear window defogger
Terminal
connector
ON Battery voltage
B42 1 Ground
OFF 0
Is the inspection result normal?
YES >> GO TO 4.
NO >> GO TO 5.
4. CHECK GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect rear window defogger.
3. Check continuity between rear window defogger connector and ground.
cardiagn.com
Is the inspection result normal?
YES >> GO TO 6.
NO >> Repair or replace harness.
5. CHECK HARNESS CONTINUITY
1. Turn ignition switch OFF.
2. Disconnect rear window defogger relay connector and rear window defogger.
3. Check continuity between rear window defogger relay connector and rear window defogger connector.
1. CHECK FILAMENT
Check the filament for damage or open circuits.
Refer to DEF-35, "Inspection and Repair".
Is the inspection result normal?
YES >> Inspection End.
NO >> Repair filament. Refer to DEF-35, "Inspection and Repair".
Heats the heating wire with the power supply from the rear window defogger relay to prevent the door mirror B
from fogging up.
Component Function Check INFOID:0000000010294862
C
1. CHECK DOOR MIRROR DEFOGGER LH
Check that heating wire of door mirror defogger LH is heated when turning the rear window defogger switch
ON. D
Is the inspection result normal?
YES >> Door mirror defogger is OK.
NO >> Refer to DEF-25, "Diagnosis Procedure". E
cardiagn.com
G
1. CHECK POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF. H
2. Disconnect door mirror LH.
3. Turn ignition switch ON.
4. Check voltage between door mirror LH connector and ground.
I
Terminals
Condition of rear window Voltage (V)
(+)
(–) defogger switch (Approx.) J
Door mirror LH connector Terminal
ON Battery voltage
D4 3 Ground
OFF 0 K
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace harness. DEF
Terminal Continuity
3 2 Yes
Is the inspection result normal?
YES >> Inspection End.
cardiagn.com
NO >> Replace door mirror LH. Refer to MIR-15, "DOOR MIRROR ASSEMBLY : Removal and Installa-
tion".
Heats the heating wire with the power supply from the rear window defogger relay to prevent the door mirror B
from fogging up.
Component Function Check INFOID:0000000010294866
C
1.CHECK DOOR MIRROR DEFOGGER RH
Check that the heating wire of door mirror defogger RH is heated when turning the rear window defogger
switch ON. D
Is the inspection result normal?
YES >> Door mirror defogger RH is OK.
NO >> Refer to DEF-27, "Diagnosis Procedure". E
cardiagn.com
G
1. CHECK POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF. H
2. Disconnect door mirror RH.
3. Turn ignition switch ON.
4. Check voltage between door mirror RH connector and ground.
I
Terminals
Condition of rear window de- Voltage (V)
(+)
(–) fogger switch (Approx.) J
Door mirror RH connector Terminal
ON Battery voltage
D107 3 Ground
OFF 0 K
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace harness. DEF
Terminal Continuity
3 2 Yes
Is the inspection result normal?
cardiagn.com
YES >> Inspection End.
NO >> Replace door mirror RH. Refer to MIR-15, "DOOR MIRROR ASSEMBLY : Removal and Installa-
tion".
cardiagn.com
NO >> Repair or replace the malfunctioning parts. G
3. CHECK REAR WINDOW DEFOGGER POWER SUPPLY AND GROUND CIRCUIT
Check rear window defogger power supply and ground circuit.
Refer to DEF-23, "Component Function Check". H
Is the inspection result normal?
YES >> Check intermittent incident. Refer to GI-41, "Intermittent Incident".
NO >> Repair or replace the malfunctioning parts. I
DEF
cardiagn.com
cardiagn.com
NO >> Repair or replace the malfunctioning parts. G
DEF
cardiagn.com
cardiagn.com
G
DEF
cardiagn.com
INSPECTION
1. When measuring voltage, wrap tin foil around the top of the neg- C
ative probe. Then press the foil against the wire with your finger.
SEL122R F
cardiagn.com
each filament. G
SEL263
J
3. If a filament is burned out, circuit tester registers 0 or battery
voltage.
4. To locate burned out point, move probe to left and right along fil- K
ament. Test needle will swing abruptly when probe passes the
point.
DEF
SEL265
REPAIR
REPAIR EQUIPMENT
• Conductive silver composition (Dupont No. 4817 or equivalent)
PIIA0215E
4. After repair has been completed, check repaired wire for conti-
nuity. This check should be conducted 10 minutes after silver
cardiagn.com
composition is deposited.
CAUTION:
Do not touch repaired area while test is being conducted.
SEL012D
SEL013D