B.N.M.

Institute of Technology
An Autonomous Institution under VTU
Semester: I
Course Name : Basic Electrical and Electronics Engineering Course Code: 24BEE113
L: T:P: J 1:2:2:0 CIA Marks: 50
Credits: 3 SEA Marks: 50
Hours 40 Hours Theory + 10 lab sessions SEA Duration: 03 Hours
Pre-Requisites: Physics fundamentals
Course Learning Objectives: The students will be able to
Understand different number systems and the working of fundamental building blocks
1
of digital circuits.
Understand the characteristics, operations, and applications of the Diode, Bipolar
2
junction transistors, and Operational amplifiers in electronic circuits.
3 Understand the principle of Basic Electrical Engineering concepts
Module-1: Digital Electronics Fundamentals:
Differences between Analog and Digital signals, Number System- Bloom’s
No. of
Decimal, Binary, Hexadecimal, and Octal Conversion. Boolean Cognitive
Hrs
algebra, Basic and Universal Gates, Simplification of Sum of Levels
Product (SoP), Half and Full adder, Design of simple digital circuits Apply
8
using Basic/Universal Gates (2-variable / 3-variable problems) CO1
Module–2: Rectifiers, Zener voltage Regulator and Transistor amplifier
Rectifiers: Bridge rectifier –analysis and derivations for Average value,
RMS value, Ripple Factor, Peak Inverse Voltage (PIV) and Efficiency,
Illustrative Examples.
Zener diode: Working principle, Characteristics, Application as
Apply
Voltage Regulator. 8
CO2
Bipolar Junction Transistor- Common Emitter (CE) mode input and
output characteristics, DC Load line, need for biasing & Q point,
Analysis of Voltage divider biasing using exact method (Excluding
design), Illustrative Examples, RC Coupled Amplifier.
Module–3: Operational Amplifier (Op-Amp) Fundamentals
Introduction to Op-Amp, Op-Amp Input Modes, Virtual ground and
Virtual short concept, Op-Amp Parameters-Common Mode Rejection
Ratio (CMRR). Input Offset Voltage and Current, Input Bias Current, Apply
8
Input and Output Impedance, Slew Rate. Applications of Op-Amp: CO3
Inverting amplifier, non-Inverting amplifier, Summer, Voltage
follower, Integrator, Differentiator, and Comparator.
Module–4: AC Circuit
Introduction to AC: Generation of single-phase AC and AC signal
parameters, Derivation of Average Value, RMS value, Form factor and
Apply
Crest factor for a sine wave. Analysis of R, L, C, RL, RC, and RLC 8
CO4
series circuits for AC signal, Power and power factor, Illustrative
examples.
3-phase AC supply: Generation of the 3-phase AC signal, 3-phase
connections (Star and Delta), the relation between line and phase
quantity, power equation in Star and Delta connection (No
Derivations), Illustrative examples.
Module–5: Fundamentals of Electrical wiring and Safety
Electrical wiring: Connectors and switches, a system of wiring
(conduit, casing, and capping), 2-way and 3-way control of lamp,
Electrical Tariff: Requirement of a good tariff, 2-part tariff, and
illustrative examples. Understand
8
Safety measures: Fuse, MCB & Earth Leakage Circuit Breaker CO5
(ELCB), Definition of Electric Shock, Precautions to avoid Electric
shock, Need for Earthing, Plate and pipe Earthing, Specifications of
Earthing.

Practical Experiments
Sl. No Experiments
1 Implementation and Verification of Boolean Expression using Logic Gates. (Using
Digital IC Trainer Kit)
2 Implementation of half adder and full adder using Basic Gates (using Digital IC
Trainer Kit)
3 Determine the parameters of Bridge rectifier.
4 Design of Inverting and Non-Inverting Amplifier using Op Amp
5 Design of Differentiator and Integrator using op-amp
6 Implementation of Comparator using Op-amp
7 Determine power & power factor of Incandescent lamp, fluorescent lamp and LED
lamp
8 Domestic wiring
9 Two way & Three way control of lamp
10 Measurement of earth resistance.
Course Outcomes: After completing the course, the students will be able to
Design simple combinational circuits using logic gates and understand the
24BEE113.1 concept of number systems.
Explain the working of bridge rectifier, Zener regulator and transistor as
24BEE113.2
amplifier
24BEE113.3 Design amplifiers, and mathematical circuits using operational Amplifiers
24BEE113.4 Analyze 1-phase and 3-phase AC circuits
24BEE113.5 Analyze the wiring, tariff and safety measures in an electrical system.
Reference Books
1. Electronic Devices and Circuits, David A. Bell, Oxford University Press, 5th Edition,2008
2. Electrical & Electronic Technology, Edward Hughes, Pearson, 12th edition, 2016
3. Electronic Devices, Thomas L. Floyd, Pearson Education, 9th Edition,2015.
4. Electronic Devices & Circuit Theory, Boylestad & Nashelsky, Pearson Education, 11th
Edition,
5. A Textbook of Electrical Technology, B.L.Theraja, S. Chand & Company, reprint edition
2014.
6. Generalized Electric Energy, B R Gupta, S Chand Publications, 7th Edition, 2017
7. Basic Electrical Engineering, Abhijit Chankrabarti, Sudipta Debnath, Chandan Kumar
Chanda, Mc-Graw Hill Education, 15th reprint Edition, 2017.