Scribd
Upload
14 views

Write Rfid Nodemcu - Ino

Uploaded by

Shravan Pawar
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as TXT, PDF, TXT or read online on Scribd
14 views

Write Rfid Nodemcu - Ino

Uploaded by

Shravan Pawar
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as TXT, PDF, TXT or read online on Scribd
You are on page 1/ 3

#include <SPI.

h>
#include <MFRC522.h>

constexpr uint8_t RST_PIN = D3; // Configurable, see typical pin layout above
constexpr uint8_t SS_PIN = D4; // Configurable, see typical pin layout above

MFRC522 mfrc522(SS_PIN, RST_PIN); // Instance of the class


MFRC522::MIFARE_Key key;

/* Set the block to which we want to write data */


/* Be aware of Sector Trailer Blocks */
int blockNum = 2;
/* Create an array of 16 Bytes and fill it with data */
/* This is the actual data which is going to be written into the card */
byte blockData [16] = {"Himanshu_Sharma"};

/* Create another array to read data from Block */


/* Legthn of buffer should be 2 Bytes more than the size of Block (16 Bytes) */
byte bufferLen = 18;
byte readBlockData[18];

MFRC522::StatusCode status;

void setup()
{
/* Initialize serial communications with the PC */
Serial.begin(9600);
/* Initialize SPI bus */
SPI.begin();
/* Initialize MFRC522 Module */
mfrc522.PCD_Init();
Serial.println("Scan a MIFARE 1K Tag to write data...");
}

void loop()
{
/* Prepare the ksy for authentication */
/* All keys are set to FFFFFFFFFFFFh at chip delivery from the factory */
for (byte i = 0; i < 6; i++)
{
key.keyByte[i] = 0xFF;
}
/* Look for new cards */
/* Reset the loop if no new card is present on RC522 Reader */
if ( ! mfrc522.PICC_IsNewCardPresent())
{
return;
}

/* Select one of the cards */


if ( ! mfrc522.PICC_ReadCardSerial())
{
return;
}
Serial.print("\n");
Serial.println("**Card Detected**");
/* Print UID of the Card */
Serial.print(F("Card UID:"));
for (byte i = 0; i < mfrc522.uid.size; i++)
{
Serial.print(mfrc522.uid.uidByte[i] < 0x10 ? " 0" : " ");
Serial.print(mfrc522.uid.uidByte[i], HEX);
}
Serial.print("\n");
/* Print type of card (for example, MIFARE 1K) */
Serial.print(F("PICC type: "));
MFRC522::PICC_Type piccType = mfrc522.PICC_GetType(mfrc522.uid.sak);
Serial.println(mfrc522.PICC_GetTypeName(piccType));

/* Call 'WriteDataToBlock' function, which will write data to the block */


Serial.print("\n");
Serial.println("Writing to Data Block...");
WriteDataToBlock(blockNum, blockData);

/* Read data from the same block */


Serial.print("\n");
Serial.println("Reading from Data Block...");
ReadDataFromBlock(blockNum, readBlockData);
/* If you want to print the full memory dump, uncomment the next line */
//mfrc522.PICC_DumpToSerial(&(mfrc522.uid));

/* Print the data read from block */


Serial.print("\n");
Serial.print("Data in Block:");
Serial.print(blockNum);
Serial.print(" --> ");
for (int j=0 ; j<16 ; j++)
{
Serial.write(readBlockData[j]);
}
Serial.print("\n");
}

void WriteDataToBlock(int blockNum, byte blockData[])


{
/* Authenticating the desired data block for write access using Key A */
status = mfrc522.PCD_Authenticate(MFRC522::PICC_CMD_MF_AUTH_KEY_A, blockNum,
&key, &(mfrc522.uid));
if (status != MFRC522::STATUS_OK)
{
Serial.print("Authentication failed for Write: ");
Serial.println(mfrc522.GetStatusCodeName(status));
return;
}
else
{
Serial.println("Authentication success");
}

/* Write data to the block */


status = mfrc522.MIFARE_Write(blockNum, blockData, 16);
if (status != MFRC522::STATUS_OK)
{
Serial.print("Writing to Block failed: ");
Serial.println(mfrc522.GetStatusCodeName(status));
return;
}
else
{
Serial.println("Data was written into Block successfully");
}

void ReadDataFromBlock(int blockNum, byte readBlockData[])


{
/* Authenticating the desired data block for Read access using Key A */
status = mfrc522.PCD_Authenticate(MFRC522::PICC_CMD_MF_AUTH_KEY_A, blockNum,
&key, &(mfrc522.uid));

if (status != MFRC522::STATUS_OK)
{
Serial.print("Authentication failed for Read: ");
Serial.println(mfrc522.GetStatusCodeName(status));
return;
}
else
{
Serial.println("Authentication success");
}

/* Reading data from the Block */


status = mfrc522.MIFARE_Read(blockNum, readBlockData, &bufferLen);
if (status != MFRC522::STATUS_OK)
{
Serial.print("Reading failed: ");
Serial.println(mfrc522.GetStatusCodeName(status));
return;
}
else
{
Serial.println("Block was read successfully");
}

You might also like