Scribd
Upload
21 views

Analog Integrated Circuits Lab

ECL331 Lab syllabus

Uploaded by

anamikanaircs11
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
21 views

Analog Integrated Circuits Lab

ECL331 Lab syllabus

Uploaded by

anamikanaircs11
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

ELECTRONICS & COMMUNICATION ENGINEERING

ANALOG INTEGRATED CIRCUITS CATEGORY L T P CREDIT


ECL331
AND SIMULATION LAB PCC 0 0 3 2

Preamble: This course aims to (i) familiarize students with the Analog Integrated Circuits and
Design and implementation of application circuits using basic Analog Integrated Circuits (ii)
familiarize students with simulation of basic Analog Integrated Circuits.

Prerequisite: ECL202 Analog Circuits and Simulation Lab

Course Outcomes: After the completion of the course the student will be able to

CO 1 Use data sheets of basic Analog Integrated Circuits and design and implement
application circuits using Analog ICs.

CO 2 Design and simulate the application circuits with Analog Integrated Circuits using
simulation tools.
CO 3 Function effectively as an individual and in a team to accomplish the given task.

Mapping of course outcomes with program outcomes

PO1 PO 2 PO3 PO 4 PO5 PO 6 PO7 PO8 PO9 PO PO PO


10 11 12
CO1 3 3 3 2 2
CO2 3 3 3 2 3 2 2
CO3 2 2 2 2 3 2 3

Assessment
Mark distribution

Total CIE ESE ESE Duration


Marks
150 75 75 3 hours

Continuous Evaluation Pattern


Attendance : 15 marks
Continuous Assessment : 30 marks
Internal Test (Immediately before the second series test) : 30 marks

Downloaded from Ktunotes.in


ELECTRONICS & COMMUNICATION ENGINEERING

End Semester Examination Pattern: The following guidelines should be followed regarding
award of marks
(a) Preliminary work : 15 Marks
(b) Implementing the work/Conducting the experiment : 10 Marks
(c) Performance, result and inference (usage of equipments and trouble shooting): 25 Marks
(d) Viva voce : 20 marks
(e) Record : 5 Marks

General instructions: End-semester practical examination is to be conducted immediately


after the second series test covering entire syllabus given below. Evaluation is to be conducted
under the equal responsibility of both the internal and external examiners. The number of
candidates evaluated per day should not exceed 20. Students shall be allowed for the
examination only on submitting the duly certified record. The external examiner shall endorse
the record.

Course Level Assessment Questions (Examples only)

Course Outcome 1 (CO1): Use data sheets of basic Analog Integrated Circuits and design and
implement application circuits using Analog ICs.
1. Measure important opamp parameters of µA 741 and compare them with the data provided
in the data sheet
2. Design and implement a variable timer circuit using opamp
3. Design and implement a filter circuit to eliminate 50 Hz power line noise.
Course Outcome 2 and 3 (CO2 and CO3): Design and simulate the application circuits with
Analog Integrated Circuits using simulation tools.
1. Design a precission rectifier circuit using opamps and simulste it using SPICE
2. Design and simulate a counter ramp ADC
List of Experiments

I. Fundamentals of operational amplifiers and basic circuits [Minimum seven experiments


are to be done]
1. Familiarization of Operational amplifiers - Inverting and Non inverting amplifiers,
frequency response, Adder, Integrator, Comparators.
2. Measurement of Op-Amp parameters.
3. Difference Amplifier and Instrumentation amplifier.
4. Schmitt trigger circuit using Op–Amps.
5. Astable and Monostable multivibrator using Op-Amps.
6. Waveform generators using Op-Amps - Triangular and saw tooth
7. Wien bridge oscillator using Op-Amp - without & with amplitude stabilization.

Downloaded from Ktunotes.in


ELECTRONICS & COMMUNICATION ENGINEERING
8. RC Phase shift Oscillator.
9. Active second order filters using Op-Amp (LPF, HPF, BPF and BSF).
10. Notch filters to eliminate the 50Hz power line frequency.
11. Precision rectifiers using Op-Amp.

II. Application circuits of 555 Timer/565 PLL/ Regulator(IC 723) ICs [ Minimum three
experiments are to be done]
1. Astable and Monostable multivibrator using Timer IC NE555
2. DC power supply using IC 723: Low voltage and high voltage configurations,
Short circuit and Fold-back protection.
3. A/D converters- counter ramp and flash type.
4. D/A Converters - R-2R ladder circuit
5. Study of PLL IC: free running frequency lock range capture range

III. Simulation experiments [The experiments shall be conducted using SPICE]


1. Simulation of any three circuits from Experiments 3, 5, 6, 7, 8, 9, 10 and 11 of
section I
2. Simulation of Experiments 3 or 4 from section II

Textbooks
1. D. Roy Choudhary, Shail B Jain, “Linear Integrated Circuits,”
2. M. H. Rashid, “Introduction to Pspice Using Orcad for Circuits and Electronics”, Prentice Hall

Downloaded from Ktunotes.in

You might also like