Scribd
Upload
27 views

Data Communication Lecture 9

Uploaded by

Kazi Redwan
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
27 views

Data Communication Lecture 9

Uploaded by

Kazi Redwan
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 17

Bandwidth Utilization (Part 1):

WDM and TDM


Course Code: COE 3201 Course Title: Data Communication

Dept. of Computer Engineering


Faculty of Engineering

Lecture No: 8 Week No: 9 Semester:


Lecturer:
Lecture Outline

1. Wavelength-division multiplexing (WDM)


2. Time-division multiplexing (TDM)
3. Synchronous TDM
Wavelength-division multiplexing
(WDM)
• Wavelength-division multiplexing (WDM) is designed
to use the high-data-rate capability of fiber-optic
cable.
• The optical fiber data rate is higher than the data rate
of metallic transmission cable but using a fiber-optic
cable for a single line wastes the available bandwidth.
• WDM allows us to combine several lines into one.
• WDM is conceptually the same as FDM, except that the
multiplexing and demultiplexing involve optical signals
transmitted through fiber-optic channels.
• The idea is the same: We are combining different signals of
different frequencies.
• The difference is that the frequencies are very high.
• Figure 6.10 gives a conceptual view of a WDM multiplexer
and demultiplexer.
• Very narrow bands of light from different sources are
combined to make a wider band of light. At the receiver,
the signals are separated by the demultiplexer.
Figure 6.10: Wavelength-division multiplexing
• Although WDM technology is very complex, the basic
idea is very simple.
• We want to combine multiple light sources into one
single light at the multiplexer and do the reverse at the
demultiplexer.
• The combining and splitting of light sources are easily
handled by a prism.
Figure 6.11: Prisms in wave-length division multiplexing
Time-division multiplexing
(TDM)
• Time-division multiplexing (TDM) is a digital process that
allows several connections to share the high bandwidth of
a link.
• Instead of sharing a portion of the bandwidth as in FDM,
time is shared. Each connection occupies a portion of time
in the link.
• Figure 6.12 gives a conceptual view of TDM.
• Note that the same link is used as in FDM; here, however,
the link is shown sectioned by time rather than by
frequency.
• In the figure, portions of signals 1, 2, 3, and 4 occupy
the link sequentially.

Figure 6.12: TDM


Synchronous TDM
• We can divide TDM into two different schemes:
synchronous and statistical.
• In synchronous TDM, each input connection has an
allotment in the output even if it is not sending data.
• Time Slots and Frames: In synchronous TDM, the data flow
of each input connection is divided into units, where each
input occupies one input time slot. Each input unit
becomes one output unit and occupies one output time
slot. However, the duration of an output time slot is n
times shorter than the duration of an input time slot.
Synchronous TDM

Figure 6.13: Synchronous time-division


multiplexing
Synchronous TDM
Example 6.5: In Figure 6.13, the data rate for each input connection is 1
kbps. If 1 bit at a time is multiplexed (a unit is 1 bit), what is the duration
of 1. each input slot, 2. each output slot, and 3. each frame?
Solution: We can answer the questions as follows:
1. The data rate of each input connection is 1 kbps. This means that the
bit duration is 1/1000 s or 1 ms. The duration of the input time slot is 1
ms (same as bit duration).
2. The duration of each output time slot is one-third of the input time
slot. This means that the duration of the output time slot is 1/3 ms.
3. Each frame carries three output time slots. So the duration of a frame
is 3 × (1/3) ms, or 1 ms. The duration of a frame is the same as the
duration of an input unit.
Synchronous TDM
Example 6.5: Figure 6.14 shows synchronous TDM with a data
stream for each input and one data stream for the output. The
unit of data is 1 bit. Find (a) the input bit duration, (b) the output
bit duration, (c) the output bit rate, and (d) the output frame rate.

Figure 6.14: Example 6.6


Synchronous TDM
Synchronous TDM
Example 6.5: Four 1-kbps connections are multiplexed together. A unit is 1 bit.
Find (1) the duration of 1 bit before multiplexing, (2) the transmission rate of
the link, (3) the duration of a time slot, and (4) the duration of a frame.
Books

[1] Forouzan AB. Data communications & networking.


5th ed., Tata McGraw-Hill Education.
References

1. Prakash C. Gupta, “Data communications”, Prentice Hall India Pvt.


2. William Stallings, "Data and Computer Communications”, Pearson
3. Forouzan, B. A. "Data Communication and Networking. Tata McGraw." (2005).

You might also like