Installation Material Overview

Description

Cable
Site installation kit sealing

Antenna
support
19-Inch Rack System

Cable ladder &

profile
Cable
sealing Cable ladder &
profile

Misc. Inst. mtrl.

Grounding material

Common fastening material

P013395D

16/1551-LZA 701 6009/1 Uen F

Copyright

© Ericsson AB 2016, 2017. All rights reserved. No part of this document may
be reproduced in any form without the written permission of the copyright
owner.

Disclaimer

The contents of this document are subject to revision without notice due to
continued progress in methodology, design and manufacturing. Ericsson shall
have no liability for any error or damage of any kind resulting from the use of
this document.

Trademark List

All trademarks mentioned herein are the property of their respective owners.
These are shown in the document Trademark Information.

16/1551-LZA 701 6009/1 Uen F | 2017-11-08

 Contents

Contents

1 Introduction 1
1.1 Indoor Installation Material 1
1.2 Outdoor Installation Material 2

2 Antenna Supports 4
2.1 Antenna Brackets 4
2.2 Freestanding Antenna Supports 5
2.3 Mounting Tubes 6

3 Feeder System 7
3.1 Commscope™ Feeder System 7
3.2 RFS Feeder System 7
3.3 Rosenberger Jumper Cables 8
3.4 Feeder Accessories 8

4 Grounding Material 10
4.1 Grounding Cable Kits 11
4.2 Grounding Cables, Coils 12
4.3 Grounding Cables 12
4.4 Grounding Wire Kits 12
4.5 Grounding Accessories 13
4.6 Aluminum Grounding 13

5 Cable Routing and Support 17

5.1 Cable Ladder Kits 18
5.2 Cable Tray Kits 19
5.3 Cable Tube Kits 20
5.4 Cable Suspension 21
5.5 Cable Hoisting 21

6 Cable Inlets 22

7 RBS Support 24

8 DF-OVP 25

9 Tools and Safety Equipment 26

16/1551-LZA 701 6009/1 Uen F | 2017-11-08

Installation Material Overview

10 Miscellaneous Installation Material 30

11 References 31

16/1551-LZA 701 6009/1 Uen F | 2017-11-08

 Introduction

1 Introduction

This document is an overview of recommended installation products and

cables for macro RBS Sites.

The document provides valuable information for network design, site planning,
and site installation.

1.1 Indoor Installation Material

The following figure and table show example of needed installation material for
an indoor site.

16/1551-LZA 701 6009/1 Uen F | 2017-11-08 1

 Installation Material Overview

B
300 Minimum

A C
C

C C
800 Maximum
C C 300 Minimum

Unit of measurement: mm P023991A

Figure 1 Example of Indoor Installation

Table 1 Indoor Installation Material

Pos. Product Reference
A Cable Routing Support Cable Routing and Support on page 17
B Cable Inlet Cable Inlets on page 22
C Grounding Material Grounding Material on page 10

1.2 Outdoor Installation Material

The following figure and table show example of needed installation material for
an outdoor site.

2 16/1551-LZA 701 6009/1 Uen F | 2017-11-08

 Introduction

A
C

C C
P015674B

Figure 2 Example of Outdoor Installation

Table 2 Indoor Installation Mat

Pos. Product Reference
A Cable Routing Support Cable Routing and Support on page 17
B Cable Inlet Cable Inlets on page 22
C Grounding Material Grounding Material on page 10

16/1551-LZA 701 6009/1 Uen F | 2017-11-08 3

 Installation Material Overview

2 Antenna Supports

This section presents brackets and fastening solutions for antennas and other
antenna near-products.

2.1 Antenna Brackets

The following figure and table show example of different antenna brackets for
wall, mast, and roof sites.

A B D

P022114B

Figure 3 Example of Antenna Brackets

Table 3 Wall-Mounted Antenna Brackets

Pos. Antenna Bracket Description Product Number
- Universal support for mast One kit needed for one pole. SXK 107 2126/1
and tower
A Wall Support, Light For mounting tubes. SXK 107 2833/1
B Parallel bracket kit For mounting tubes Ø 60 – SXK 107 2834/1
90 mm
-- Double Antenna Support SXK 107 2835/1
C Triple Antenna Support SXK 107 2836/1

4 16/1551-LZA 701 6009/1 Uen F | 2017-11-08

 Antenna Supports

Pos. Antenna Bracket Description Product Number

D Top Spire Support SXK 107 2837/1
- Wall Mount, MHGA SXK 118 0932/1
- Extension Kit, MHGA SXK 118 0933/1
- Parallel Cog Support SXK 107 2843/1

2.2 Freestanding Antenna Supports

The following figure and table show example of freestanding antenna
supports.

P022110B

Figure 4 Freestanding Antenna Supports

Table 4 Freestanding Antenna Supports

Pos. Antenna Support Description Product Number
A Foundation with adjustable NTM 201 3164/1
strut supports, 3 m
B Roof Tube Single-based, 2 m NTM 201 1205/1
C Free-standing Ballast Kit, 2 m NTM 201 3862/1

16/1551-LZA 701 6009/1 Uen F | 2017-11-08 5

 Installation Material Overview

2.3 Mounting Tubes

The following figure and table show mounting tubes for fastening of antennas
and equipment.

P022113B

Figure 5 Mounting Tubes

Table 5 Mounting Tubes

Mounting Tube Length Product Number
Mounting tube, aluminum 1.6 m SXA 120 729/16
Ø = 60 mm, t = 3 mm 2.5 m SXA 120 748/1
Mounting tube, aluminum 1m SXA 120 747/1
Ø = 75 mm, t = 3.5 mm 2.9 m SXA 120 215/29
Mounting tube, aluminum 4m SXA 120 216/40
Ø = 90 mm, t = 5 mm
Mounting tube, aluminum 1.5 m SXA 120 752/1
Ø = 114 mm, t = 5 mm
Mounting tube, steel 2m SXA 120 765/1
Ø = 60 mm, t = 2.9 mm
Mounting tube, steel 3m SXA 120 765/2
Ø = 60 mm, t = 2.9 mm
Mounting tube, steel 1m SXA 120 765/3
Ø = 76 mm, t = 2.9 mm
Mounting tube, steel 3m SXA 120 765/4
Ø = 76 mm, t = 2.9 mm
Mounting tube, steel 4m SXA 120 765/5
Ø = 90 mm, t = 3.2 mm
Mounting tube, steel 1m SXA 120 765/6
Ø = 114 mm, t = 3.6 mm

6 16/1551-LZA 701 6009/1 Uen F | 2017-11-08

 Feeder System

3 Feeder System

The antenna feeder system consists of RF feeder cables, RF jumper cables,

connectors, and other accessories like grounding kit and clamps.

The following sections present available feeder products. Use connectors and
feeder cables from the same supplier.

3.1 Commscope™ Feeder System

The following tables show available feeder product from Commscope™.

Table 6 Commscope™ Feeder Cables and Accessories

Feeder Cable Product Number Associated Connector Product Number
and Grounding Kit
1/2-inch feeder cable, FAB 802 0241/1 7-16 (m) connector RPT 899 165/1
aluminum
500 m, supplied on Grounding kit incl. NGT 901 29/1
drums 0.6 m cable

7/8-inch feeder cable, FAB 802 0242/1 7-16 (f) connector RNT 899 125/1
aluminum
500 m, supplied on Grounding kit incl. NGT 901 29/2
drums 0.6 m cable

1 1/4-inch feeder cable, FAB 102 2512/1 7-16 (f) connector RNT 899 126/1
aluminum
400 m, supplied on Grounding kit incl. NGT 901 29/3
drums 0.6 m cable

1 5/8-inch feeder cable, FAB 802 0244/1 7-16 (f) connector RNT 899 127/1
aluminum
300 m, supplied on Grounding kit incl. NGT 901 29/4
drums 0.6 m cable

Table 7 Commscope™ Jumper Cables

Jumper Cable Connectors Length Product Number
1/2-inch jumper cable, 7-16 (m) to 7-16 (m) 0.5 m TSR 951 70/05
copper 1m TSR 951 70/1
2m TSR 951 70/2
3m TSR 951 70/3
5m TSR 951 70/5
10 m TSR 951 70/10
1/2-inch jumper cable, 7-16 (m) to 7-16 (m) 1.5 m TSR 951 322/1
copper right angled 2.5 m TSR 951 322/2
3.5 m TSR 951 322/3

3.2 RFS Feeder System

The following tables show available feeder product from Commscope™.

16/1551-LZA 701 6009/1 Uen F | 2017-11-08 7

 Installation Material Overview

Table 8 RFS Feeder Cables and Accessories

Feeder Cable Product Number Connector and Product Number
Grounding Kit
7/8-inch feeder cable, FAB 802 0779/1 7-16 (f) connector RNT 899 174/1
aluminum
500m, supplied on Grounding kit incl. NGT 901 25/1
drums 0.5 m cable

1 1/4-inch feeder cable, FAB 802 0807/1 7-16 (f) connector RNT 899 175/1
aluminum
500m, supplied on Grounding kit incl. NGT 901 26/1
drums 0.5 m cable

1 5/8-inch feeder cable, FAB 802 0782/1 7-16 (f) connector RNT 899 176/1
aluminum
500 m, supplied on Grounding kit incl. NGT 901 27/1
drums 0.5 m cable

Table 9 RFS Jumper Cables

Jumper Cable Connectors Length Product Number
1/2-inch jumper cable 7-16 (m) to 7-16 (m) 1m TSR 951 351/1
2m TSR 951 352/1
3m TSR 951 353/1

3.3 Rosenberger Jumper Cables

Table 10 Rosenberger Jumper Cables

Jumper Cable Connectors Length Product Number
1/2-inch jumper cable 7-16 (m) to 7-16 (m) 1m TSR 951 331/1
2m TSR 951 331/2
3m TSR 951 331/3
5m TSR 951 331/5
1/2-inch jumper cable 7-16 (m) to 7-16 (m) 1.5 m TSR 951 333/1
right angled 2.5 m TSR 951 333/2
3.5 m TSR 951 333/3
1/2-inch jumper cable 4.3-10 (m) to 7-16 (m) 1m TSR 951 367/1
22 mm wrench 2m TSR 951 367/2
3m TSR 951 367/3

3.4 Feeder Accessories

This section show useful accessories for feeder installations, for example
clamps and sealing solutions.

Table 11 Feeder Cable Clamps

Feeder Clamp Number of Feeders Product Number
Clamp for 1/2-inch feeder cable 2 NTM 201 1223/2
4 NTM 201 1223/4
6 NTM 201 1223/6
Clamp for 7/8-inch feeder cable 2 NTM 201 1224/2
4 NTM 201 1224/4

8 16/1551-LZA 701 6009/1 Uen F | 2017-11-08

 Feeder System

Feeder Clamp Number of Feeders Product Number

6 NTM 201 1224/6
Clamp for 1 1/4-inch feeder cable 2 NTM 201 1225/2
4 NTM 201 1225/4
6 NTM 201 1225/6
Clamp for 1 5/8-inch feeder cable 2 NTM 201 1226/2
4 NTM 201 1226/4
6 NTM 201 1226/6

Table 12 Cable Sealing and Marking

Product Product Number
Sealing tape NTM 201 2426
Coaxial connector sealing kit MPB 134 01/1
Cold shrink sleeve for sealing of feeder and jumper
connectors. 150 mm.
Coaxial connector sealing kit MPB 134 02/1
Cold shrink sleeve for sealing of feeder and jumper
connectors. 300 mm.
Marking Set GSM NTM 201 207/1
Marking Set WCDMA & LTE NTM 201 2964/1
Cable Ties. Plastic covered stainless steel. SET 145 095/457
For cable bundles up to Ø130 mm
Weather Sealing Closures MPB 901 029/1
Reusable sealing closure for jumper cables with
7/16-connectors.

16/1551-LZA 701 6009/1 Uen F | 2017-11-08 9

 Installation Material Overview

4 Grounding Material

This section describes material needed for grounding of telecommunication

Sites. Installation principles are found in the document Grounding Guidelines
for RBS Sites, page 31.

P016101A

Figure 6 Examples of Outdoor Grounding

10 16/1551-LZA 701 6009/1 Uen F | 2017-11-08

 Grounding Material

P016239A

Figure 7 Examples of Indoor Grounding

4.1 Grounding Cable Kits

This section describes available grounding kits with different cable lengths.

Table 13 Grounding Kits

Grounding Kit Description Length Product Number
Grounding Cable Kit Including earth bar, 12 m NTM 201 3669/1
35 mm2, Yellow/Green cable lugs and 17 m NTM 201 3669/2
installation material 25 m 4/NTM 201 201/3
Grounding Cable Kit Including earth bar, 25 m 4/NTM 201 201/2
35 mm2, Black cable lugs and
installation material

16/1551-LZA 701 6009/1 Uen F | 2017-11-08 11

 Installation Material Overview

Grounding Kit Description Length Product Number

Cabinet grounding cable Including cable lugs and 1m 5/NTM 201 201/3
kit installation material 2m 5/NTM 201 201/4
35 mm2, Yellow/Green
Cabinet grounding cable Including cable lugs and 2m 5/NTM 201 201/2
kit installation material
25 mm2, Black

4.2 Grounding Cables, Coils

This section contains grounding cables delivered in coils.

Table 14 Grounding Cables, Coils

Grounding Cable Connectors Length Product Number
Grounding Cable Open-end 100 m TEL 901 07/1
16 mm2, Black
Grounding Cable Open-end 100 m TEL 901 08/1
25 mm2, Black
Grounding Cable Open-end 100 m TEL 901 07/2
16 mm2, Yellow/Green
Grounding Cable Open-end 100 m TEL 901 08/2
25 mm2, Yellow/Green

4.3 Grounding Cables

This section shows grounding cables with cable lug in different lengths,
dimensions, and colors.

Table 15 Grounding Cables

Grounding Cable Connectors Length Product Number
Grounding cable Cable lug to open-end 2m RPM 119 1647/2
16 mm2, Black 5m RPM 119 1647/5
Grounding cable Cable lug to open-end 2m RPM 119 1649/2
25 mm2, Black 5m RPM 119 1649/5
Grounding cable Cable lug to open-end 2m RPM 119 1648/2
16 mm2, Yellow/Green 5m RPM 119 1648/5
Grounding cable Cable lug to open-end 2m RPM 119 1650/2
25 mm2, Yellow/Green 5m RPM 119 1650/5
Grounding cable Dual M6, angled lug 2m RPM 119 2061/2
16 mm2, Black 5m RPM 119 2061/5
Grounding cable Dual M6, angled lug 2m RPM 119 2062/2
16 mm2, Yellow/Green 5m RPM 119 2062/5

4.4 Grounding Wire Kits

This section shows grounding wires in different lengths and dimensions.

12 16/1551-LZA 701 6009/1 Uen F | 2017-11-08

 Grounding Material

Table 16 Grounding Wire Kits

Grounding Wire Kit Description Length Product Number
Grounding Wire Kit Including cable lugs and 70 m NTM 201 3425/1
35 mm2 installation material

Grounding Wire Kit Including cable lugs and 40 m NTM 201 4145/1
25 mm2 installation material

Grounding Wire Kit Including cable lugs and 40 m 9/NTM 201 230/1
35 mm2 installation material
Open-end
Rooftop Grounding Kit, Including aluminum 40 m NTM 201 3755/1
50 mm2 conductor and jointing
clamps

4.5 Grounding Accessories

This section shows useful accessories.

Table 17 Grounding Accessories

Grounding Wire Kit Description Product Number
Grounding Bar Including cable lugs and NTM 201 3326/1
installation material
Main Earth Terminal 5 connections NGT 901 30/1
10 connections NGT 901 30/2
Insulated Grounding Bar SXK 107 2847/1
Grounding Joint Clamps C89 50 pcs SNT 901 14/1
Cable lug M8 For 16 mm2 cable, 100 pcs SNG 904 60/1
SNG 904 60/2
For 25 mm2 cable, 100 pcs

4.6 Aluminum Grounding

This section shows products that can be combined in different solutions for
aluminum grounding. Figure 8 and Figure 9 show examples of aluminum
grounding solutions. Table 18 describes the products used in the different
solutions.

16/1551-LZA 701 6009/1 Uen F | 2017-11-08 13

 Installation Material Overview

3
4

5
8 7 6
Ge8264A

Figure 8 Example, Aluminum Grounding Solution

14 16/1551-LZA 701 6009/1 Uen F | 2017-11-08

 Grounding Material

8
7
Ge8265A

Figure 9 Example, Aluminum Grounding Solution

16/1551-LZA 701 6009/1 Uen F | 2017-11-08 15

 Installation Material Overview

6
5

Ge8282C

Figure 10 Example, Aluminum Grounding Solution

Table 18 Aluminum Grounding

Pos Grounding Wire Kit Product Number
1 Stainless steel screw branch clamp SXA 120 761/1
2 Round aluminum cable TPM 901 02/150M
3 Grounding bar NTM 201 3326/1
4 Grounding terminal SXA 120 762/1
5 Round galvanized steel cable TPM 901 03/80M
6 Cross-connector SXA 120 754/1
7 Grounding rod for steel cable SXK 107 2873/1
8 Connection terminal for grounding rod universal SXA 120 760/1

16 16/1551-LZA 701 6009/1 Uen F | 2017-11-08

 Cable Routing and Support

5 Cable Routing and Support

P016253C

Figure 11 Example of Cable Ladder and Profile Use

16/1551-LZA 701 6009/1 Uen F | 2017-11-08 17

 Installation Material Overview

5.1 Cable Ladder Kits

P015311B

Figure 12 Greenfield Site Tower Kit, NTM 201 3501/1

Table 19 Greenfield Site Tower Kit

Product Description Product Number
Greenfield site tower kit Complete set of outdoor NTM 201 3501/1
installation material.
Includes cable runs, grounding
wire, grounding rods, grounding
bar and installation instructions,
delivered in a transport optimized
export package.

18 16/1551-LZA 701 6009/1 Uen F | 2017-11-08

 Cable Routing and Support

P016252B

Figure 13 Cable Ladders and Profiles

Table 20 Cable Ladder Kits

Product Description Product Number
Cable ladder kit, outdoor Carries cables between the base NTM 201 3138/1
station shelter and the tower,
mast, or antenna support.
Includes 2 cable ladders (L =
2.25 m, W= 400 mm) and
fastening material.
Cable ladder cover, outdoor Protects cables and cable runs NTM 201 3159/1
from falling objects and sun
damage.
Includes 2 covers (L= 1.125 m,
W = 400 mm)
Basic cable ladder kit, indoor Indoor cable ladders, 9 m. NTM 201 3416/2
Includes cable ladders,
grounding system, marking and
sealing materials.
Cable ladder kit (W = 300 mm) Coated cable ladders for indoor NTM 201 3160/2
installations.
Includes 2 cable ladders (L =
2.25 m, W = 300 mm) and
installation material
Cable ladder kit (W = 400 mm) Coated cable ladders for indoor NTM 201 3745/1
installations.
Includes 2 cable ladders (L =
2.25 m, W = 400 mm) and
installation material

5.2 Cable Tray Kits

Table 21 Cable Tray Kits

Product Description Product Number
Mesh Tray Set Cable run for indoor installation. NTM 201 4151/1
L = 2.5 m, W = 75 mm
Cable tray with cover Cable tray for cables in shelter SXK 107 2023/1
and RBS room. Cables are fixed
with cable ties.
Includes cover 2 cable runs (L =
2 m) and covers.

16/1551-LZA 701 6009/1 Uen F | 2017-11-08 19

 Installation Material Overview

Product Description Product Number

Cable tray fitting profile Cable tray for cables in shelter NTM 201 4152/1
and RBS room. Cables are fixed
with cable ties.
L = 2 m, W = 50 mm
Cable Tray 0.6 m, Coated Gray Cable tray for cables in shelter SXK 107 2158/2
and RBS room. Cables are fixed
with cable ties.
Includes 2 cable runs (L = 0.6 m)
and fastening material.
Cable Tray 2 m, Coated Gray Cable tray for cables in shelter SXK 107 761/2
and RBS room. Cables are fixed
with cable ties.
Includes 2 cable runs (L = 2 m)
and fastening material.
Clamping band Bracing strap to strap cables in SXA 120 1869/1
walls.
L = 2.5 m

5.3 Cable Tube Kits

Table 22 Cable Tube Kits

Product Description Product Number
Tube kit, indoor Flexible tubes for protection of NTM 201 218/3
cables in indoor installation.
Includes 2 tubes (L = 3 m, Ø)
and fastening material.
Tube kit, outdoor Tubes for routing and protection NTM 201 3727/1
of outdoor cables, houses up to
three optical cables and three
power cables.
Includes 5 tubes (L = 1.7 m, Ø =
35 mm) and fastening material.
Outdoor slitted conduit, 27 mm Plastic tube for routing and NTM 201 3929/1
protection of outdoor cables. Can
be opened for routing of
terminated cables and
expansions. Houses for example
three optical cables and three
power cables to RRUs.
Includes 5 tubes (L = 2 m, Ø = 23
mm)
Outdoor slitted conduit, 48 mm Plastic tube for routing and NTM 201 3929/2
protection of outdoor cables. Can
be opened for routing of
terminated cables and
expansions. Houses for example
six optical cables and six power
cables to RRUs.
Includes 5 tubes (L = 2 m, Ø = 44
mm)
Flexible cable tube, 25 m Plastic flexible outdoor cable NTM 201 3811/1
tube. Houses for example three
optical cables and three power
cables to RRUs.
Includes flexible tube (L = 25 m,
Ø = 40 mm), fastening material
and pull wire.

20 16/1551-LZA 701 6009/1 Uen F | 2017-11-08

 Cable Routing and Support

5.4 Cable Suspension

Table 23 Wire Suspension Kits

Product Description Product Number
Wire suspension kit 25 m SXK 107 2850/1
Steel wire that cables are 50 m SXK 107 2851/1
strapped to. For installation of 100 m SXK 107 2852/1
long cables in for example
suspended ceilings and garages.
Including fastening material.
Excluding tie straps.

5.5 Cable Hoisting

Figure 14 Cable Hoisting

Table 24 Cable Hoisting

Product Description Product Number
Cable hoisting grip Hoisting and support kit for three NTM 201 3728/1
optical cables and three power
cables. One hoisting grip is used
for each cable.

16/1551-LZA 701 6009/1 Uen F | 2017-11-08 21

 Installation Material Overview

6 Cable Inlets

Cable inlets prevent rodents, dust, and water from entering the building.

03
6

9 12
15
0

P017102B

Figure 15 Example of Cable Sealing Use

Table 25 Cable Inlets and Cable Sealing

Product Description Product Number
Cable inlet, ComPlus 6×1 For cables 1/4-inch to 7/8-inch. NTM 201 3448/1
Cable inlet, ComPlus 6×2 For cables 1/4-inch to 7/8-inch. NTM 201 3448/2
Cable inlet, ComPlus 6×1 For cables 7/8-inch to 1 5/8-inch. NTM 201 3449/1
Cable inlet, ComPlus 6×2 For cables 7/8-inch to 1 5/8-inch. NTM 201 3449/2
Cable Inlet Cable inlet for 1/4-inch to 7/8- NTM 201 3879/1
inch feeder cables and 5–16 mm
cables
Coaxial connector sealing kit Cold shrink sleeve for sealing of MPB 134 01/1
feeder and jumper connectors.
150 mm.
Coaxial connector sealing kit Cold shrink sleeve for sealing of MPB 134 02/1
feeder and jumper connectors.
300 mm.

22 16/1551-LZA 701 6009/1 Uen F | 2017-11-08

 Cable Inlets

Product Description Product Number

Weather Sealing Closures Reusable sealing closure for MPB 901 029/1
jumper cables with 7/16-
connectors.
Sealing tape NTM 201 2426

16/1551-LZA 701 6009/1 Uen F | 2017-11-08 23

 Installation Material Overview

7 RBS Support

This section shows different 19-inch racks and tip-protection for RBS 6201.

P017956D

Figure 16 Example of Rack Frames

Table 26 19-inch Racks

Product Description Product Number
Rack frame 19-inch rack for walls. 16 U NTM 201 3605/1
Rack frame 19-inch rack for walls. 48 U NTM 201 3604/2
Rack Frame, flat pack 19-inch rack, flat pack. 12 U SDC 901 538/1

Table 27 RBS 6201 Tip Protection

Product Description Product Number
Anti-Tip RBS 6201 Steel 225 mm NTM 201 4146/1
Anti-Tip RBS 6201 Strap 550 mm NTB 101 24/1

24 16/1551-LZA 701 6009/1 Uen F | 2017-11-08

 DF-OVP

8 DF-OVP

The DF-OVP is used for protection against lightning currents, transients, and
surges. More expansion kits can be added to protect the equipment.

It is recommended to protect the Site equipment with Overvoltage Protection

(OVPs). All Site OVPs are tested and approved together with Ericsson RBS
products.

The DF-OVPs are available in both fixed and flexible product packages.

Table 28 Distribution Frame

Product Description Product Number
Distribution Frame (DF-OVP) Empty distribution frame with NBA 101 30/9
space for 12 single OVPs.
Suitable for alarm, GPS receiver
unit, PCM, and ESB.

Table 29 SAU Kit

Product Description Product Number
Support Alarm Unit (SAU) Kit For connection of external NTM 503 109/63
alarms.
Includes 10 m cable.

Table 30 OVP Kits

Product Description Product Number
OVP kit, 8 external alarms For up to 8 external alarm NTB 101 242/2
connections.
OVP-kit, 2 T1/J1/E1, 100-120 Ω For transmission connections. NTB 101 242/3
Includes 10 m cable
OVP-kit, 2 E1 75 Ω For transmission connections. NTB 101 242/4
Includes 10 m cable

Table 31 SPD Kits

Product Description Product Number
DC Out for −48 V DC. For RBS 5 m cable INF 901 6089/41
6201. 10 m cable INF 901 6089/42
SPD Module for protection of
RBS when feeding DC power to
for example MINI-LINK PT or
RRU. Includes cable.
SPD Module for protection of 5 m cable NTB 101 242/7
one RRU. Includes cable. 10 m cable NTB 101 242/8

16/1551-LZA 701 6009/1 Uen F | 2017-11-08 25

 Installation Material Overview

9 Tools and Safety Equipment

This section list useful tools and safety equipment needed when working at
telecommunication sites. Both for personal and system safety.

P004513A

Figure 17 Full Body Harness, LYB 921 53/1 and LYB 921 53/2

26 16/1551-LZA 701 6009/1 Uen F | 2017-11-08

 Tools and Safety Equipment

P017811A

Figure 18 Tower Work Set, LYA 175 115/1

16/1551-LZA 701 6009/1 Uen F | 2017-11-08 27

 Installation Material Overview

P017812A

Figure 19 Work Line Set, LYA 175 117/1

P017814A

Figure 20 Rescue Line Set, LYA 175 119/1

Table 32 Tools and Safety

Product Description Product Number
Personal tool set, large High-quality standard tool set for LTT 601 135/1
site and RBS installations.
Special toolkit Special tools for installation and LTT 601 151/1
maintenance of Ericsson RBSs.
Includes extractor tool QDM,
IDM, EMILY shield, slotted
socket 27/32 mm, wrist strap kit,
RU extract handle with button,

28 16/1551-LZA 701 6009/1 Uen F | 2017-11-08

 Tools and Safety Equipment

Product Description Product Number

spanner for angle connector 7/8,
and power cable tool.
Bird Site Analyze Antenna system testing tool LPK 102 101/9
Full Body Harness Size S – M LYB 921 53/1
Size L - XL LYB 921 53/2
Tower Work Set Work set for work in tower, LYA 175 115/1
masts, and poles. Full body
harnesses ordered separately.
Work Line Set Work set for work in tower, LYA 175 117/1
masts, and poles. Full body
harnesses ordered separately.
Safety Line Set LYA 175 118/1
Rescue Line Set LYA 175 119/1

16/1551-LZA 701 6009/1 Uen F | 2017-11-08 29

 Installation Material Overview

10 Miscellaneous Installation Material

P008211F

Figure 21 Examples of Content in Common Fastening Material, 7/NTM 201

201

Table 33 Miscellaneous
Product Description Product Number
Common Installation Material A kit with the most common used 7/NTM 201 201
(see figure Figure 21) installation material at a telecom
site.
Includes for example cable ties,
plugs, screws, tape.
Additional Fastening Material A kit with the most common NTM 201 1491/1
fastening material at a telecom
site.
Includes for example fasteners,
and anchor screws for wall, roof,
and ceiling installations.
Cable ties, plastic coated steel 230 mm SET 145 064/230
457 mm SET 145 095/457

30 16/1551-LZA 701 6009/1 Uen F | 2017-11-08

 References

11 References

• Grounding Guidelines for RBS Sites

16/1551-LZA 701 6009/1 Uen F | 2017-11-08 31