APPENDIX A - ATTACHMENT 4

QP STANDARD FOR EQUIPMENT IDENTIFICATION AND TAG

NUMBERING SYSTEM – DUKHAN FIELDS
DOC. No. QP-ENG-STD-013 Rev. 00

TABLE OF CONTENTS
Page No.
FOREWORD .................................................................................................................... 6
1.0 OBJECTIVE ................................................................................................. 7
2.0 SCOPE ......................................................................................................... 7
3.0 APPLICATION ............................................................................................. 7
4.0 TERMINOLOGY ........................................................................................... 8
4.1 DEFINITIONS ............................................................................................... 8
4.2 ABBREVIATIONS ......................................................................................... 8
5.0 REFERENCE STANDARDS ........................................................................ 9
5.1 QP Engineering Standards ........................................................................... 9
5.2 International Standards ................................................................................. 9
6.0 TAG REQUEST PROCESS ....................................................................... 10
6.1 Tag Request/Advice Form .......................................................................... 10
6.2 Requesting Tag Numbers ........................................................................... 10
7.0 TAG NUMBER RULES .............................................................................. 11
8.0 IDENTIFICATION OF MAJOR PLANT EQUIPMENT ................................ 12
8.1 Major Plant Equipment ............................................................................... 12
8.2 Major Equipment Drivers and Major Components ...................................... 13
8.3 Skid Mounted Equipment and Vendor Supplied Packages ......................... 13
9.0 IDENTIFICATION OF PIPING AND PIPELINES........................................ 14
9.1 Pipelines in Process Areas ......................................................................... 14
9.2 Pipelines in Wellhead and Manifold Areas .................................................. 14
9.3 Line Identification ........................................................................................ 16
9.4 Line Size ND ............................................................................................... 16
9.5 Piping Class Identification ........................................................................... 16
9.6 Insulation Codes ......................................................................................... 16
9.7 Pipe and Anchor Supports .......................................................................... 17
9.8 Piping Fittings and Mechanical Specialties ................................................. 17
10.0 IDENTIFICATION OF VALVES .................................................................. 18
10.1 Valve Identification...................................................................................... 18
10.2 Hand Operated Valves ............................................................................... 18
10.3 Identification of Valves in Wellheads .......................................................... 19
10.4 Identification of Valves in Manifold Areas ................................................... 19
11.0 IDENTIFICATION OF ELECTRICAL EQUIPMENT ................................... 19
11.1 Electrical Equipment Identification .............................................................. 19

Doc. No.: QP-ENG-STD-013 Rev. 00 Date: 01/07/2019 Page 2 of 86

 QP STANDARD FOR EQUIPMENT IDENTIFICATION AND TAG
NUMBERING SYSTEM – DUKHAN FIELDS
DOC. No. QP-ENG-STD-013 Rev. 00

11.2 Identification of Electrical Sockets and Luminaries ..................................... 22

11.3 Coding for Typical Street Lighting Systems ................................................ 23
11.4 Identification of Electrical Cables ................................................................ 23
11.5 Identification of Electrical Equipment in Wellhead Areas ............................ 25
11.6 Dukhan Power Supply and Substations ...................................................... 25
12.0 IDENTIFICATION OF INSTRUMENTATION.............................................. 28
12.1 Identification of Instrument Functions ......................................................... 28
12.2 Identification of Shutdown (Safety) Valves in Wellhead Areas ................... 29
12.3 Identification of Instrument Multicore Cables .............................................. 29
12.4 Instrument Junction Boxes ......................................................................... 30
12.5 Identification of Individual Signal Cores and Wires ..................................... 30
12.6 Identification of Instrument Panels, Gauge Boards & Cabinets .................. 31
13.0 IDENTIFICATION OF HVAC ASSOCIATED MECHANICAL AND
ELECTRICAL EQUIPMENT ....................................................................... 33
14.0 IDENTIFICATION OF RESCUE AND SAFETY EQUIPMENT ................... 34
15.0 IDENTIFICATION OF TELECOMMUNICATIONS / SECURITY AND IT
EQUIPMENT .............................................................................................. 35
16.0 IDENTIFICATION OF FIRE AND GAS DETECTION EQUIPMENT........... 39
16.1 Identification of Fire and Gas Equipment (As specified) ............................. 39
16.2 Identification of Fire and Gas Detection Devices Installed as Individual
Circuits in Process Plants/Sub Stations ...................................................... 40
16.3 Identification of Fire and Gas Detection Devices Installed in Buildings/
Living Quarters as Multi-Circuits per Fire Zone.......................................... 40
16.4 Identification of Fire and Gas Detection Devices Installed in Buildings/
Living Quarters as Single Circuits per Fire Zone ........................................ 41
16.5 Identification of Fire and Gas Devices In Wellhead Areas: ......................... 41
16.6 Identification of Fire and Gas Cables, Junction Boxes, Panels and
Cabinets ..................................................................................................... 41
17.0 IDENTIFICATION OF EQUIPMENT INSTALLED IN WELLHEADS .......... 42
18.0 IDENTIFICATION OF EQUIPMENT INSTALLED IN MANIFOLD AREAS 43
18.1 Gas Lift Manifold Equipment Tagging ......................................................... 43
18.2 Oil Manifold Equipment Tagging ................................................................. 45
18.3 Extended Oil Manifold Equipment Tagging ................................................. 45
19.0 IDENTIFICATION OF MOBILE EQUIPMENT ............................................ 46
20.0 IDENTIFICATION OF LABORATORY EQUIPMENT................................. 48
21.0 IDENTIFICATION OF EQUIPMENT IN HOUSING..................................... 49
22.0 IDENTIFICATION OF BUILDINGS ............................................................ 49
23.0 IDENTIFICATION OF CIVIL COMPONENTS ............................................ 50
Doc. No.: QP-ENG-STD-013 Rev. 00 Date: 01/07/2019 Page 3 of 86
 QP STANDARD FOR EQUIPMENT IDENTIFICATION AND TAG
NUMBERING SYSTEM – DUKHAN FIELDS
DOC. No. QP-ENG-STD-013 Rev. 00

23.1 Tagging of Civil Components in General Areas .......................................... 50

23.2 Tagging for Civil Component Inside Buildings ............................................ 50
23.3 Tagging for Civil Component in Manifolds .................................................. 50
23.4 Tagging for Civil Component in Wellhead Areas ........................................ 51
24.0 IDENTIFICATION SEWAGE TREATMENT PLANT SPECIALISED
EQUIPMENT .............................................................................................. 53
25.0 LIST OF APPENDICES .............................................................................. 54
APPENDIX A: DUKHAN AREA CODES ......................................................................... 55
APPENDIX B: INSTRUMENT FUNCTION CODES ........................................................ 56
APPENDIX C: TAG REQUEST/ADVICE FORM............................................................. 57
APPENDIX D: REQUEST FOR VARIANCE TO STANDARD ........................................ 59
APPENDIX E1: PWI WELLS – TYPE 1 PRESSURE BLEED LINE WITH GLV
VALVES ...................................................................................................... 60
APPENDIX E2: PWI WELLS – TYPE 2 PRESSURE BLEED LINE WITH BV
VALVES ...................................................................................................... 63
APPENDIX F: STANDARD EQUIPMENT TAGS – GAS LIFT WELLS ........................... 66
APPENDIX G: STANDARD EQUIPMENT TAGS – WATER SOURCE WELLS ............. 67
APPENDIX H: STANDARD EQUIPMENT TAGS – RE-CIRCULATION WELLS ............ 68
APPENDIX I1: OIL WELLS – TYPE 1 WITH HYDRAULIC WELLHEAD CONTROL
PANEL, PRESSURE BLEED LINE WITH GLV VALVES ........................... 69
APPENDIX I2: OIL WELLS – TYPE 2 WITH HYDRAULIC WELLHEAD CONTROL
PANEL, PRESSURE BLEED LINE WITH BV VALVES .............................. 72
APPENDIX I3: OIL WELLS – TYPE 3 WITHOUT HYDRAULIC WELLHEAD
CONTROL PANEL, PRESSURE BLEED LINE WITH BV VALVES ........ 75
APPENDIX J1: POWER WATER INJECTION – TYPICAL WELLHEAD (TYPE-1)
P&ID ........................................................................................................... 78
APPENDIX J2: POWER WATER INJECTION – TYPICAL WELLHEAD (TYPE-2)
P&ID ........................................................................................................... 79
APPENDIX K: GAS LIFT WELL – TYPICAL WELLHEAD (WITHOUT WHCP) P&ID ..... 80
APPENDIX L: WATER SOURCE WELL – TYPICAL WELLHEAD P&ID ........................ 81
APPENDIX M: RE-CIRCULATION WELL – TYPICAL WELLHEAD P&ID ...................... 82
APPENDIX N1: OIL WELL – TYPICAL WELLHEAD (TYPE-1) P&ID ............................. 83
APPENDIX N2: OIL WELL – TYPICAL WELLHEAD (TYPE-2) P&ID ............................. 84
APPENDIX N3: OIL WELL – TYPICAL WELLHEAD (TYPE-3) P&ID ............................. 85
REVISION HISTORY LOG ............................................................................................. 86

Doc. No.: QP-ENG-STD-013 Rev. 00 Date: 01/07/2019 Page 4 of 86

 QP STANDARD FOR EQUIPMENT IDENTIFICATION AND TAG
NUMBERING SYSTEM – DUKHAN FIELDS
DOC. No. QP-ENG-STD-013 Rev. 00

LIST OF TABLES:
TABLE 1: LETTER CODE FOR IDENTIFICATION OF MAJOR PLANT
EQUIPMENT ............................................................................................. 12
TABLE 2: MAJOR EQUIPMENT DRIVER AND MAJOR COMPONENT CODES ..... 13
TABLE 3: PIPELINE SERVICE IDENTIFICATION .................................................... 15
TABLE 4: PIPING AND FITTING / MECHANICAL SPECIALTIES CODES ............... 17
TABLE 5: VALVE CODES ......................................................................................... 18
TABLE 6: HAND OPERATED VALVE CODES ......................................................... 19
TABLE 7: ELECTRICAL EQUIPMENT AND COMPONENT CODES ........................ 20
TABLE 8: ELECTRICAL CABLE CODES .................................................................. 24
TABLE 9: INSTRUMENT CABLE / JUNCTION BOX CODES ................................... 30
TABLE 10: PANELS / CABINET CODES .................................................................. 31
TABLE 11: HVAC MECHANICAL AND ELECTRICAL EQUIPMENT CODES........... 33
TABLE 12: RESCUE AND SAFETY EQUIPMENT CODES ...................................... 34
TABLE 13: TELECOMS / SECURITY AND IT EQUIPMENT IDENTIFICATION
CODES..................................................................................................... 35
TABLE 14: FIRE AND GAS IDENTIFICATION CODES ............................................ 39
TABLE 15: WELL TYPE CODES............................................................................... 42
TABLE 16: GAS LIFT MANIFOLD NUMBERS .......................................................... 44
TABLE 17: OIL MANIFOLD NUMBERS .................................................................... 46
TABLE 18: DEPARTMENT CODES .......................................................................... 46
TABLE 19: SPECIFIC MOBILE EQUIPMENT LETTER CODES ............................... 47
TABLE 20: BUILDING IDENTIFICATION CODES .................................................... 50
TABLE 21: CIVIL COMPONENTS ............................................................................. 51
TABLE 22: SEWAGE TREATMENT PLANT SPECIALISED EQUIPMENT ............... 53

Doc. No.: QP-ENG-STD-013 Rev. 00 Date: 01/07/2019 Page 5 of 86

 QP STANDARD FOR EQUIPMENT IDENTIFICATION AND TAG
NUMBERING SYSTEM – DUKHAN FIELDS
DOC. No. QP-ENG-STD-013 Rev. 00

FOREWORD

This Standard has been developed by Projects, Engineering and Procurement Service
Directorate (VP) in coordination with Operations Directorate (VO) to replace Dukhan Internal
Procedure, Document number QPR-DKN-005 Procedure for Tagging of Equipment in Dukhan
Fields.

The issue of this Standard Revision 00 (Refer to Revision History Log) supersedes Doc
Number QPR-DKN-005.

It should be noted that the Tag Numbering System as defined in this Standard has maintained
that same system of Tagging Equipment as defined in the above procedure including Area
Codes, Equipment Identifications Codes, Well Codes, Pipeline Services etc. and includes
additional tagging requirements, equipment and area codes as approved by Dukhan
Operations.

Where cross-references to other parts of this Standard are made, the referenced section
number is shown in brackets (). Other documents referenced by this Standard are listed in
(5.0).

This document is subjected to periodical review as per QP-IMS-PRC-001 and QP-IMS-PRC-

002, to re-affirm its adequacy or to conform to any changes in the corporate requirements or
to include new developments on its subject.

The Custodian of this Standard is Manager, Engineering Info & Standards (PTD) Division of
the Engineering Services Department (PT), who is responsible for the accuracy and quality of
its contents and for its future revisions, where these are required to reflect industry trends or
changes to QP business practices. All comments, recommendations, clarifications about this
document shall be forwarded to PTD. [email protected]

Doc. No.: QP-ENG-STD-013 Rev. 00 Date: 01/07/2019 Page 6 of 86

 QP STANDARD FOR EQUIPMENT IDENTIFICATION AND TAG
NUMBERING SYSTEM – DUKHAN FIELDS
DOC. No. QP-ENG-STD-013 Rev. 00

1.0 OBJECTIVE
The objective of this Standard is to define the formal system for unique tag numbering
and identification of QP equipment (assets) located or to be installed in Dukhan Fields,
including electrical, instrumentation ancillary items, fire and gas equipment, HVAC,
telecommunications equipment’s, panels, boards and cabinets, junction boxes,
structures, cabling, piping and valves. This includes Documents & Drawings, physical
Tag nameplates, databases and all document/enterprise asset management’s
systems.

This Standard replaces QPR-DKN-005, refer to Foreword on page (4) of this

Engineering Standard for specific details.

2.0 SCOPE
This Standard sets out the identification and tag numbering system for all equipment
to be installed in Dukhan Fields. Appendix A defines all Dukhan areas, which fall under
the requirements of this Standard.

This Standard DOES NOT cover the following:

a) Dukhan Arab “D” Gas Recycling Plant (Refer to QP-ENG-STD-014)

b) Dukhan Acid Gas Removal Plant (AGRP), (Refer to ES-0-07-0020)

3.0 APPLICATION
3.1 QP and/or any of QP Consultants/Contractor responsible for providing design and
engineering services for EPIC or PCR works where installation of new equipment is
included shall apply this Standard. Contractors own ‘in-house’ tagging systems shall
not be used, only exception being FEED projects. See below.

3.2 Tagging for FEED projects shall be given a dummy tag number by the contractor. The
same shall be NOTED in every submitted drawing and document. Moreover, the EPIC
Contractor at EPIC stage shall request the permanent tag numbers to replace the
dummy tag numbers, which were assigned in the FEED stage.

3.3 Vendor supplied packages, skid equipment, shall follow the requirements of this
Standard. The Project Engineer and/or EPIC Contractor shall be responsible for
implementing tag numbers to the Vendor P&ID’s in accordance with this Standard.
(See 8.3)

3.4 QP and/or its Consultants/Contractors shall complete Discipline specific Tag

Schedules/Standard Templates indicating the details of the device or component
related to each Tag number issued along with a listing of all unused Tag numbers
issued. For templates for completing these Schedules refer to QP Standard QP-ENG-
STD-018. These include but are not limited to the below templates:
Electrical Cable Schedule Doc No. ES-2-08-0100
Electrical Distribution Board Schedule Doc No. ES-2-08-0102
Electrical Utility Data Sheets Doc No. ES-2-08-0103

Doc. No.: QP-ENG-STD-013 Rev. 00 Date: 01/07/2019 Page 7 of 86

 QP STANDARD FOR EQUIPMENT IDENTIFICATION AND TAG
NUMBERING SYSTEM – DUKHAN FIELDS
DOC. No. QP-ENG-STD-013 Rev. 00

Instrument / F&G Cable Schedule Doc No. ES-4-08-0100

Instrument Schedule Doc No. ES-4-08-0102
Valve Index Doc No. ES-5-08-0002
Line Designation Table Doc No. ES-5-08-0102
Mechanical and Piping Equipment List Doc No. ES-5-08-0103

3.6 Strict compliance with this Standard is required. Any exceptions or deviations from this
Standard, along with their merits and justification, shall be brought to the attention of
the custodian (PTD) for review, consideration and amendment as required by
completing part 1 of form ES-0-08-0014. Sample of this form is shown in Appendix D.
The form is available on QP Intranet under Engineering Services Department.

4.0 TERMINOLOGY

4.1 DEFINITIONS
Contractor - A party employed by QP to perform works or services under
a Contract
SAP - SAP is a software used to manage the Enterprise Resource
Planning (ERP). It has many modules such as Maintenance,
Contracting, HR, Finance, etc.

4.2 ABBREVIATIONS
AGRP - Acid Gas Removal Plant
ANSI - American National Standards Institute
DCS - Distributed Control System
EPIC - Engineering, Procurement, Installation and Commissioning
F&G - Fire and Gas
FEED - Front End Engineering Design
GIS - Geographic Information System
HVAC - Heating Ventilation Air Conditioning
OE(D) - Manager, Operations Engineering (Dukhan)
OEE(D) - Asst. Manager, Engineering (Dukhan)
OEE/6(D) - Sr. Designer (Operations Engineering (Dukhan))
P & ID - Piping & Instrument Diagram
PCR - Plant Change Requests
PEFD - Process Engineering Flow Diagram
PLC - Programmable Logic Controller
PM-SAP - Preventive Maintenance – SAP module
PMS - Power Management System

Doc. No.: QP-ENG-STD-013 Rev. 00 Date: 01/07/2019 Page 8 of 86

 QP STANDARD FOR EQUIPMENT IDENTIFICATION AND TAG
NUMBERING SYSTEM – DUKHAN FIELDS
DOC. No. QP-ENG-STD-013 Rev. 00

PTD - Manager, Engineering Design, Info & Standards

QP - Qatar Petroleum
RBMI - Risk Base Maintenance Inspection
SCADA - System Control and Data Acquisition
SC-SSSV - Surface Control–Sub Surface Safety Valve
SCS - Sub-Station Control System
SLD - Single Line Diagram
SSV - Shutdown Safety Valve
UEFD - Utility Engineering Flow Diagram

5.0 REFERENCE STANDARDS

5.1 QP Engineering Standards
ES-0-07-0020 : Plant Equipment Tag Identifiers - Corporate
QP-ENG-STD-014 : Plant Tag Identifiers for Dukhan Arab ‘D‘ Gas Recycling
Plant
ES-2-08-0100 : Electrical Cable Schedule
ES-2-08-0102 : Electrical Distribution Board Schedule
ES-2-08-0103 : Electrical Utility Data Sheets
ES-4-08-0100 : Instrument / F&G Cable Schedule
ES-4-08-0102 : Instrument Schedule
ES-5-00-0002 : Valve Index
ES-5-08-0102 : Line Designation Table
ES-5-08-0103 : Mechanical and Piping Equipment List
ES-4-08-0104 : Template Instrument Name Plates (7 Sheets)
QP-ENG-STD-018 : Development of Technical Drawings

5.1.1 In all instances, users of this Standard shall refer to the latest approved version of the
above standards. The latest approved versions are as posted on QP Intranet under
Engineering Services Department. For confirmation of the latest approved versions,
users of this Standard may contact QP PTD Help Desk Engineering Services
Department on +974 4013 6633.

5.2 International Standards

ISA 5.1-2009 : Instrument Symbols and Identification

Doc. No.: QP-ENG-STD-013 Rev. 00 Date: 01/07/2019 Page 9 of 86

 QP STANDARD FOR EQUIPMENT IDENTIFICATION AND TAG
NUMBERING SYSTEM – DUKHAN FIELDS
DOC. No. QP-ENG-STD-013 Rev. 00

6.0 TAG REQUEST PROCESS

6.1 Tag Request/Advice Form

6.1.1 Tag numbers shall be requested using the Tag Request/Advice forms. Samples of
these are shown in Appendix C - Page 1 and 2. Form ES-0-08-0005 Sheet 1 (Appendix
C Page 1) shall be used for requesting all equipment types with the exception of
Pipeline numbers. Requests for Pipeline numbers shall use form ES-0-08-0005 Sheet
2 (Appendix C Page 2).

6.1.2 The Tag Request advice forms as referenced above may be used for Arab D Gas
Recycling Plant (Refer QP-ENG-STD-014) and AGRP (Refer ES-0-07-0020) as well
as Dukhan Fields, however this applicability shall be clearly indicated on each Tag
request form in the space provided. Intermixing of the above three areas/facilities is
not permitted in the same request.

6.1.3 The Tag Request/Advise forms are available on QPNet under Engineering Services
Department “Forms”.

6.2 Requesting Tag Numbers

6.2.1 Any Consultant/Contractor or QP employee may initiate the tag request. All information
shall be inputted into the relevant boxes and only codes in accordance with this
Standard or Engineering Standard QP-ENG-STD-014 & ES-0-07-0020 (See 7.0 c) as
applicable shall be used. Each component/item description (See appropriate Tables in
this Standard) shall be quoted as well as the service it provides.

6.2.2 For the request of “looped tags,” the requestor shall indicate, in the form, the primary
equipment on top of the list followed by all of its associated equipment. The looped
equipment shall be clearly identified as one group in the form.

6.2.3 Requests for large block of numbers shall be justified by attaching the relevant
documents/drawings to Tag Request Advice Form such as:
a) For Mechanical equipment: P&ID, Equipment Layout
b) For Electrical equipment: SLD, Equipment Layout, Block diagram
c) For Instrument equipment: P&ID, Equipment Layout, Loop diagram
d) For Telecomm & HVAC equipment: Block diagram, Equipment Layout
e) For F&G equipment: Block diagram, Equipment Layout, Fire Zone layout

6.2.4 The requested equipment shall be clearly marked and highlighted on attached
documents/drawings.

6.2.5 Tag Number request initiated by Consultant/Contractor shall be submitted to relevant

QP Project Engineer for authorization.

6.2.6 The QP Project Manager/Engineer must then approve the form by completing the
“Authorized By” Section before submitting to OEE/6 (D). This is to ensure that the
codes are in accordance with the relevant Standard (See 6.0) and to eliminate the
possibility of repeat requests for the same items.

Doc. No.: QP-ENG-STD-013 Rev. 00 Date: 01/07/2019 Page 10 of 86

 QP STANDARD FOR EQUIPMENT IDENTIFICATION AND TAG
NUMBERING SYSTEM – DUKHAN FIELDS
DOC. No. QP-ENG-STD-013 Rev. 00

6.2.7 Forms completed in accordance with the above will be endorsed by OEE/6 (D) and
authorized by OEE (D) as appropriate and tags will be allocated. The form will be
returned to the QP Project Manager/Engineer who will record that the requested tags
have been issued. The QP Project Manager/Engineer shall acknowledge receipt by
signing at the bottom of the form and sending one copy back to OEE/6 (D) and one
copy to the original requester.

7.0 TAG NUMBER RULES

7.1 Tag numbers shall not be duplicated on any single area (Appendix A). Each item of the
same equipment type (same alpha code) within the same area (same area code) shall
have unique set of sequential numbers.

7.2 Instrumentation within the same loop shall use the same sequence number for all
devices within the loop.

7.3 Only equipment letter codes shown in this Standard shall be used for Dukhan Fields.
For Equipment letter codes for Arab D Gas Recycling Plant refer to (QP-ENG-STD-
014) and for AGRP refer to (ES-0-07-0020).

7.4 Where two or more items of equipment are performing the same duty, whether on
standby or online, they shall be tagged with same tag number but be uniquely identified
by the addition of a suffix commencing A, B, C, etc. In the case of some electrical
equipment an alphanumeric suffix may be used e.g. A1, A2, A3, etc. or 01, 02, 03, etc.,
to identify the cubicle and panel numbers within a motor control center (See 8.2).

7.5 The removal of an item of equipment from a particular process or system and
replacement by equipment of the same function shall leave the tag number unchanged.
However, details of the change must be recorded in SAP to ensure update of details
related to equipment, manufactures details and maintenance history.

7.6 In case of “removal” of existing tags, EPIC Contractor / Project Engineer shall provide
a “photo” for every tag before removal. All relevant data to be deleted from SAP by QP,
Drawings, System and documents shall be updated by the contractor.

7.7 Any upgrade modification or replacement (as above) for any facilities in Dukhan fields
shall require tag request to be raised by QP job officer with the inclusion of the actual
Tags.

7.8 CONTRACTORS shall use tag numbers issued by QP only.

Doc. No.: QP-ENG-STD-013 Rev. 00 Date: 01/07/2019 Page 11 of 86

 QP STANDARD FOR EQUIPMENT IDENTIFICATION AND TAG
NUMBERING SYSTEM – DUKHAN FIELDS
DOC. No. QP-ENG-STD-013 Rev. 00

8.0 IDENTIFICATION OF MAJOR PLANT EQUIPMENT

8.1 Major Plant Equipment

All major plant equipment shall be identified by a tag number composed of an area
code, letter code followed by a unique 4 digit sequential number as illustrated in the
following example:

Table 1: Letter Code for Identification of Major Plant Equipment

Description Code
Air dryers, Analyser House, Vendor Packages/Skids and miscellaneous A
equipment.
Blower B
Columns C
Diesel Engine D
Heat transfer : heat exchangers, humidifiers, condensers, coolers, E
reboilers, cooling towers
Furnaces, heaters, steam boilers (fired), F
Generators G
HVAC Packages (See section 11 for HVAC Equipment Items) H
Jets (ejectors, injectors and eductors) J
Compressors K
Lifting equipment / Crane and mechanical handling equipment / Loading L
Arms / Hoists / Winch, Roller shutter door, Elevators, Conveyors.
Mobile Equipment use as first letter (See section 19 and Table 19) M
Not used N
Pumps P
Not used R
Gravity Mechanical separators, filters, filter skimmers centrifuges, S
coalesces, screens, sieves, pulsation dampers, strainers, cyclones,
expellers, thickeners, dust collectors, hydrocyclones, Odour control unit
Atmospheric Tanks general, fire water storage, fresh water storage, T
interceptors, reservoirs, sumps
Electrolyser U
Vessels incl. Pressure storage vessels, accumulator, vacuum, air receiver V
Weighing Equipment W
Flare tips, burn pit, stack X
Pig receivers/launchers and Spheres Z

Doc. No.: QP-ENG-STD-013 Rev. 00 Date: 01/07/2019 Page 12 of 86

 QP STANDARD FOR EQUIPMENT IDENTIFICATION AND TAG
NUMBERING SYSTEM – DUKHAN FIELDS
DOC. No. QP-ENG-STD-013 Rev. 00

8.2 Major Equipment Drivers and Major Components

8.2.1 A single alpha character as given in Table 1, is combined with a second alpha character
(see Table 2) to describe a major mechanical equipment driver / transmission item or
major components requiring to be uniquely identified for maintenance or inspection
purposes.
Table 2: Major Equipment Driver and Major Component Codes
Description Code Description Code
Air Motor A Electric Motor M
Tube Bundle B Pneumatic Motor N
Cartridge C Rotor R
Expander E Stator S
Fan F Turbine T
Gearbox G Variable speed drive V
Hydraulic Motor H Exhaust X

8.2.2 The 4 digit sequential number for codes shown in Table 2 should be the same as the
number used for the item it is driving as explained in the following example:

The motor of pump 24-P-0001A shall be tagged 24-PM-0001A

8.2.3 Plant equipment having multiple drivers or associated components shall have the same
tag number and be suffixed with a letter as shown in the following example:

Fans of heat exchanger 24-E-0002 shall be tagged 24-EF-0002A, 24-EF-0002B, 24-

EF-0002C etc. the fan motors would be tagged 24-EFM-0002A, 24-EFM-0002B, 24-
EFM-0002C, etc.

8.2.4 Multiple modifiers can be used to identify items of equipment associated with each
other. For example a generator would be tagged 24-G-0001, the diesel engine of the
same generator would be tagged 24-GD-001 and the gearbox of the same diesel
engine would be tagged 24-GDG-001.

8.3 Skid Mounted Equipment and Vendor Supplied Packages

8.3.1 Vendors supplying skids and packages shall be encouraged to tag the package internal
equipment components in accordance with this Standard. Each skid or vendor supplied
package shall be given a tag identifier “A” for vendor packages or “H” for HVAC
packages (See Table 1) as shown in the following format:

Doc. No.: QP-ENG-STD-013 Rev. 00 Date: 01/07/2019 Page 13 of 86

 QP STANDARD FOR EQUIPMENT IDENTIFICATION AND TAG
NUMBERING SYSTEM – DUKHAN FIELDS
DOC. No. QP-ENG-STD-013 Rev. 00

8.3.2 Package equipment internal tags shall be prefixed with the actual package tag. The
drawing will not show this prefix but will refer to a note on the drawing stating ‘All
package tag numbers will be prefixed with 24-A-0001 (appropriate tag number) unless
otherwise stated. Examples of these tags are as follows:

Example of package tag for Vessel: 24-A-0001 V-01, V-02, V-03, etc.

Example of package tag for Pressure TX: 24-A-0001 PT-01, PT-02, PT-03 etc.

8.3.3 The physical tag plates will not show the package tag. All internal package tag alpha
codes shall be in accordance with this Standard.

9.0 IDENTIFICATION OF PIPING AND PIPELINES

9.1 Pipelines in Process Areas

All Piping & Pipelines in P&IDS, UEFD’s, PEFD’s, isometrics, piping, pipeline drawings
and in GIS shall be identified by a line number consisting of the following components:

Line Number Example: 12 - 0001 - 6” - OC - 31101 - 4EN

12 0001 6” OC 31011 4EN

Area Code Sequence Nominal Pipeline Piping Class Insulation
See Number Diameter Service Identification in Code in
Appendix (9.3) (ND) Code accordance with accordance
A or Well (9.4) see Shell DEP with Shell
No. See (Table 3) 31.38.01.12- DEP
(9.2) Gen. and DEP 31.10.03.10-
31.38.01.15-Gen Gen. see (9.6)
see (9.5)
Line Numbering – See (9.3) Use Dukhan Existing Pipe Specs
for PCR modifications

9.2 Pipelines in Wellhead and Manifold Areas

9.2.1 Pipelines from wellheads shall be numbered as shown in 9.1 above by using the well
number in place of the area code as per following example:

9.2.2 The Wellhead numbers shall be supplied by the Dukhan Drilling Department on
request. Work-over wells shall not be suffixed with the “work over letter” when
requesting for a tag.

9.2.3 Pipelines in Manifold Areas

For identification of Pipelines in Manifold Areas refer to section (18)

Doc. No.: QP-ENG-STD-013 Rev. 00 Date: 01/07/2019 Page 14 of 86

 QP STANDARD FOR EQUIPMENT IDENTIFICATION AND TAG
NUMBERING SYSTEM – DUKHAN FIELDS
DOC. No. QP-ENG-STD-013 Rev. 00

Table 3: Pipeline Service Identification

Pipeline Service Code Pipeline Service Code
Air breathing AB Oil crude OC
Air fire detection AF Oil drain OD
Air instrument / Dried
AI Oil fuel OF
Compressed Air
Air process AP Oil hydraulic OH
Air service AS Oil lube OL
Chemical glycol CG Oil Multiphase OM
Chemical injection CI Oil seal OS
Clarified Water/Drain from Filtration
Chlorine Gas CLG PE
Feed tank
Liquid Polymer (Concentrate) / Dilute
Chlorine Solution CLS PYL
Polymer Solution
Dry Condensate DC Raw Sewage
Domestic drain DD Sewage/Grit RS
Dry Gas DG Sewage Pumping
Surplus Activated Sludge / Activated
Dry Oil DO SAS
Sludge in Balancing Tank
Digested Sludge DS Stabilized Condensate (wet) SC
Drain / Sewage drain / Grit Washing
Foam Fire FF Drains / Sludge Drain/ Sludge SD
Dewatering Concentrate
Filtered Water FPE Skimmed Oil SO
Backwash Reject FWD Steam condensate SW
Gas condensate GC Steam SX
Carbon Dioxide (CO2) GD
Thickened Sludge / Overflow to Works
Gas fuel GF Return Pumping Station / Drain from TS
Aerobic Digester
Screen Washing Drains / Motive
Gas inert GI Water for Cl2 Solution / Treated TSE
Sewage Effluent
Gas Multiphase GM Water cooling WC
Gas process GP Water drain WD
Gas refrigeration GR Wet Gas Separated WG
Gas seal GS Water fire (fighting) WF
Gas vent and flare GV Water heating WH
Halon fire fighting HF Water injection WI
Hot Oil (Heat transfer
HO Water potable (hot or cold) WP
oil)
Jet fuel JF Water raw (sea water) WR
Mud kill MK Water service (hose stations) WS
All Plant Drain Mixture MSD Water tempered or treated WT

Doc. No.: QP-ENG-STD-013 Rev. 00 Date: 01/07/2019 Page 15 of 86

 QP STANDARD FOR EQUIPMENT IDENTIFICATION AND TAG
NUMBERING SYSTEM – DUKHAN FIELDS
DOC. No. QP-ENG-STD-013 Rev. 00

9.3 Line Identification

9.3.1 Line Sequence Number

The line sequence number shall be unique for each line having the same area code
(or Well code and number) pipeline ND and pipeline service, i.e. 24-0001-6-OC. Each
line shall be numbered consecutively starting with the next available number and rising
in increments of one.

9.3.2 Assigning Line Identification

The process lines shall be numbered from apparatus to apparatus, battery limit to
battery limit. When the pressure, volume or temperature changes considerably, the
numbering shall also be changed. This normally changes at piping class/product
service changes or major branches. Parallel lines shall be numbered separately. Limit
of line number is the first isolation valve inside station boundary fence (battery limit).

For vertical vessels the numbering of all corresponding inlet and outlet lines should
start from the top down.

Outgoing pipelines from area / plant to another, either directly or indirectly via bridge,
pipe rack or other routing systems, will obtain line numbers corresponding to the
area/plant of origin, seen in the direction of flow.

9.4 Line Size ND

Line Size ND (Nominal Diameter) to use imperial units. Due to the existing tagging
records for Line Numbers utilizing the inch (“) icon in various drawings within the
Dukhan fields, the same shall be maintained in the Line Tag string, except for RBMI
and Stencilling on site which shall use the two-character “IN” instead of the inch (“)
icon.

9.5 Piping Class Identification

Piping Classes shall be in accordance with the following DEPs as defined below:*

a) Shell DEP 31.38.01.12-Gen Piping Classes – Refining and Chemicals*

b) Shell DEP 31.38.01.15-Gen Piping Classes – Exploration and Production*

*Note: For the new projects, Shell DEP can be utilized but for PCR and EPIC
modifications of existing lines, the current Dukhan pipe spec should be followed.

9.6 Insulation Codes

Insulation codes shall be in accordance with Shell DEP 31.10.03.10-Gen*

*Note: For the new projects, Shell DEP can be utilized but for PCR and EPIC
modifications of existing lines, the current Dukhan insulation codes should be followed.

Doc. No.: QP-ENG-STD-013 Rev. 00 Date: 01/07/2019 Page 16 of 86

 QP STANDARD FOR EQUIPMENT IDENTIFICATION AND TAG
NUMBERING SYSTEM – DUKHAN FIELDS
DOC. No. QP-ENG-STD-013 Rev. 00

9.7 Pipe and Anchor Supports

Pipe and Anchor Supports shall be coded PSP for Pipe Supports and ASP for Anchor
Support and shall be number uniquely as shown in the following example:

The sequence number shall start at the first available number (0001) and rise in
increments of one along the Pipeline or group of pipelines.

Pipe and Anchor supports located in Wellheads shall be numbered as above but use
well type and well number see (9.2.2) and Table 4.

9.8 Piping Fittings and Mechanical Specialties

Piping & Fittings and Mechanical Specialties shall be tagged as follows:

24 – RBJ – 0001

Area Code (See Appendix A) 4 Digit Sequential Number

Alpha Code (See Table 4)

Table 4: Piping and Fitting / Mechanical Specialties Codes

Description Code
Calibration Pot CAP
Dismantling Joint DJ
Flame Arrestor FA
Sight Glass FG
Mixer MX
Expansion Joint / Rubber Expansion RBJ
joint
Conveyor Screw SCR
Silencers SIL
Steam Traps ST
Vacuum Breakers VB

Doc. No.: QP-ENG-STD-013 Rev. 00 Date: 01/07/2019 Page 17 of 86

 QP STANDARD FOR EQUIPMENT IDENTIFICATION AND TAG
NUMBERING SYSTEM – DUKHAN FIELDS
DOC. No. QP-ENG-STD-013 Rev. 00

10.0 IDENTIFICATION OF VALVES

10.1 Valve Identification

All Motor-operated valves, actuated valves, relief valves and emergency shutdown
valves are coded under the instrument discipline. A rupture disc (Disc bursting) is
designated BD. Examples of tagging these valves are as shown below:
24 – AVC – 0001

Area Code (See Appendix A) 4 Digit Sequential Number

Valve Code (See Table 5)

Table 5: Valve Codes

Description Code
Automatic Recirculation Valve/Air Release Valve ARV
Alarm Check Valve AVC
Air Vent Valve AVV
Ruptured Disc/Bursting Disc BD
Blow Down Valve BDV
Combined Air Valve CAV
Condensate Drain Valve CDV
Deluge Valve DLV
Double Regulating Valve DRV
Motor Operated Valve MOV
Pressure Vacuum Relief Valve PVRV
Remote Operating Valve ROV
Emergency Shutdown Valve SDV
Safety Relief Valve SRV
Thermal Relief Valve TRV
Valve Steam Trap STV
Solenoid Valves See Appendix B

Valve tag numbers shall be unique for each valve type (code) within the same area
(area code).

10.2 Hand Operated Valves

All hand operated valves regardless of size shown on P&ID’S shall be uniquely tagged
as shown in the following example:
24 – AVC – 0001

Area Code (See Appendix A) 4 Digit Sequential Number

Valve Code (See Table 6)

Valves NOT required to be tagged are as follows:

 Potable water system valves less than 1/2”.
 Valves installed on instrument impulse lines.
Doc. No.: QP-ENG-STD-013 Rev. 00 Date: 01/07/2019 Page 18 of 86
 QP STANDARD FOR EQUIPMENT IDENTIFICATION AND TAG
NUMBERING SYSTEM – DUKHAN FIELDS
DOC. No. QP-ENG-STD-013 Rev. 00

Table 6: Hand Operated Valve Codes

Description Code Description Code
Block Bleed Valve BBV Hydrant Water HW
Butterfly Valve BFV Hydrant Water & Fam HWF
Ball Valve BV Hydrant Valve HYV
Choke Valve CHV Line Break Valve LBV
Double Block & Bleed Valve DBV Needle Valve NLV
Diaphragm Valve DV Check Valve (None Return) NRV
Float Valve FV Plug valve PLG
Foot Valve FTV Gate Valve (Parallel Slide) PLV
Globe Valve GLV Shuttle Valve SHV
Gate Valve (wedge type) GV

Valve tag numbers shall be unique for each valve type (code) within the same location
(location code).

10.3 Identification of Valves in Wellheads

For identification of valves installed in Wellheads see section (17.0)

10.4 Identification of Valves in Manifold Areas

For identification of valves Manifold areas see section (18.0)

11.0 IDENTIFICATION OF ELECTRICAL EQUIPMENT

11.1 Electrical Equipment Identification

11.1.1 Electrical Equipment shall be identified as shown in the following example:

24 – TR – 0001

Area Code (See Appendix A) 4 Digit Sequential Number

Electrical Identifier (Table 7)

11.1.2 Electric motors for motor-operated valves shall be identified by a tag number of the
format xx-MV-yyyy. Where xx represents the area code and yyyy represents the four
digit sequential number.

11.1.3 All Electrical components (outside or inside the substation), i.e. CB, SFU, ST, etc.
within an electrical panel shall have the same sequential number as the equipment it
is associated with. For further detail refer to Section (11.6).

Doc. No.: QP-ENG-STD-013 Rev. 00 Date: 01/07/2019 Page 19 of 86

 QP STANDARD FOR EQUIPMENT IDENTIFICATION AND TAG
NUMBERING SYSTEM – DUKHAN FIELDS
DOC. No. QP-ENG-STD-013 Rev. 00

Table 7: Electrical Equipment and Component Codes

Description Code
BATT CHGR, INV, UPS
BATTERY BANK BB
BATTERY AND CHARGER
BC
BATTERY CHARGER UNIT
BATTERY ISOLATION BOX BIB
CAPACITOR BANK CAB
BOARD - DISTRIBUTION
DB
BOARD - LIGHTING
ELECTRIC TARIFF METER ETM
FEEDER PILLAR FP
INVERTER INV
MOTOR CONTROL CENTRE MCC
MAIN DISTRIBUTION BOARD MDB
SWITCH BOARD SB
UNINTERRUPTIBLE POWER SUPPLY UPS
CATHODIC PROTECTION
C.P. TRANSFORMER RECTIFIERS (SEE TRANSFORMERS)
C.P. GROUNDING BEDS CGB
C.P. BOND BOXES CPB
C.P. POSTS CPP
C.P. SUB-STATIONS CPS
CORROSION COUPON CC
CORROSION PROBE CP
CIRCUIT BREAKERS HV & MV
CIRCUIT BREAKER - AIR BREAK
CIRCUIT BREAKER - MOLDED CASE
CIRCUIT BREAKER - OIL CB
CIRCUIT BREAKER - SF6
CIRCUIT BREAKER - VACUUM
EARTHING
EARTH BAR EB
EARTH PIT EP
EARTHING ETH
NEUTRAL EARTH RESISTERS / GEN NEUT PNL GNP
GENERATORS, EXCITORS.
EXCITOR EX
GENERATOR STANDBY
G
GENERATOR FOR TURBINE
HEATERS
HEATER - ELECTRIC ELEMENT HTR
HV / LV OVERHEAD LINES
O/H LINE DISCONNECT SWITCH (SEE “SWITCH-HV” BELOW)
FUSED LINK FLNK
OVERHEAD LINE OHL
POLE POLE
Doc. No.: QP-ENG-STD-013 Rev. 00 Date: 01/07/2019 Page 20 of 86
 QP STANDARD FOR EQUIPMENT IDENTIFICATION AND TAG
NUMBERING SYSTEM – DUKHAN FIELDS
DOC. No. QP-ENG-STD-013 Rev. 00

IGNITORS
IGNITION TRANSFORMERS (SEE TRANSFORMERS)
IGNITORS XE
JB, SOCKETS, LIGHTING, MISCELLANEOUS
LIGHTING POLE / COLUMN COL
JUNCTION BOX JB
LIGHT FITTING LF
LIGHTING PHOTOCELL LPC
SOCKET - ELECTRICAL (WELDING ETC.) SKT
MOTOR - HV , MV , LV
MOTOR – MEDIUM VOLTAGE
MOTOR - LOW VOLTAGE
M
MOTOR - HIGH VOLTAGE
MOTOR – DC
MOTOR FOR MOV MV
PANELS
ARRAY COMBINER BOX ACB
PANEL – ELECTRICAL CONTROL, LOCAL CONTR.
ECP
PANEL, REMOTE CONTR. UNIT
PANEL – GENERATOR CONTROL GCP
PUSH BUTTON - START & STOP
PUSH BUTTON - EMERGENCY STOP PB
PUSH BUTTON – STAYPUT
PANEL – TERMINAL, MARSHALLING BOX PNT
PANEL – STATIC BYPASS PSB
PANEL – RELAY BOARD / PANEL RB
PANEL – RELAY & CONTROL RCP
PANEL – TAP CHANGER CONTROL TCP
PANEL - SWITCH UNITS 230/415V
EARTH SWITCH ETS
SWITCH – HAND HS
SWITCH - LOCAL ISOLATOR IS
SWITCH - FUSED UNIT SFU
SWITCH – SELECTOR
SWITCH - CHANGE OVER
SW
SWITCH – ROTARY
SWITCH - MEDIUM / LOW VOLTAGE
VARIABLE SPEED DRIVE SYSTEM (UNIT) VSDS
STARTERS, CONTACTORS
CONTACTOR CON
STARTER - HIGH VOLTAGE
ST
STARTER / VARIABLE SPEED DRIVE SYS
PANEL - MOTOR STARTER / CONTROL STP
SUB-STATIONS
SUB-STATION SS

Doc. No.: QP-ENG-STD-013 Rev. 00 Date: 01/07/2019 Page 21 of 86

 QP STANDARD FOR EQUIPMENT IDENTIFICATION AND TAG
NUMBERING SYSTEM – DUKHAN FIELDS
DOC. No. QP-ENG-STD-013 Rev. 00

SWITCH - HV
SWITCH OIL FUSE SWF
SWITCH - SF6 - HIGH VOLTAGE
SWITCH - AIR BREAK – HV SWU
SWITCH – OIL
SWITCHGEAR HV
RING MAIN UNIT RMU
SURGE ARRESTOR SA
SWITCHGEAR HV SWG
TRANSFORMERS
AUTOMATIC VOLTAGE REGULATOR AVR
HARMONIC FILTER OR TRANSFORMER HFT
REACTOR RA
TRANSFORMER - OIL FILLED
TR
TRANSFORMER - DRY TYPE
RECTIFIER TRANSFORMER (CATHODIC PROTECTION) TRR
TRANSFORMER – VOLTAGE VT
TRANSFORMER - IGNITION XMR
MISCELLANEOUS
ELECTOLYZER EY

11.2 Identification of Electrical Sockets and Luminaries

11.2.1 Identification of Sockets and Luminaries will as shown in Fig 1 below:

Fig 1. Typical Lighting Schematic

24-DB-0001

WAY
1R

ONLY THIS CABLE

TO BE NUMBERED
CABLE NO.

24-DB-0001-1R-JB2 24-DB-0001-1R-LF1-JB
24-DB-0001-1R-LF1
Main Circuit JB
24-DB-0001-1R-JB1 24-DB-0001-1R-LF2-JB

X X

24-DB-0001-1R-LF4-JB 24-DB-0001-1R-LF3-JB

24-DB-0001-1R-LF2

24-DB-0001-1R-LF3
X

24-DB-0001-1R-LF4

Doc. No.: QP-ENG-STD-013 Rev. 00 Date: 01/07/2019 Page 22 of 86

 QP STANDARD FOR EQUIPMENT IDENTIFICATION AND TAG
NUMBERING SYSTEM – DUKHAN FIELDS
DOC. No. QP-ENG-STD-013 Rev. 00

24-DB-0001 – 1R – LF1 – JB

Distribution Board Number Fitting JB

Way Number Light Fitting Number

11.2.2 Sockets (SKT) and Welding Sockets (WSKT) shall be identified in the same manner
as above, LF will be replaced with SKT for standard sockets and WSKT for welding
sockets.

11.2.3 For maintenance purposes and entry into PM-SAP, QP only issue the TAG as far as
the outgoing cable from the main for internal lighting circuits lighting D.B. and contractor
can tag the way number, light fitting number and fitting JB shown in Figure 1 above.

11.3 Coding for Typical Street Lighting Systems

Fig 2. Typical Street Lighting Schematic

24-FP-0001 Where 24 represents the Area Code and FP is Feeder Pillar

Feeder No. 1 (F1)

24- FP-0001 –F1 –HM1- LF 1/6

For street lighting high mast with 6 luminaries

24- FP-0001 –F1 –COL-1- LF 1/2

For street lighting Column with 2 luminaries

To next HM/COL

11.4 Identification of Electrical Cables

11.4.1 Electrical Cables Tag Numbers

11.4.1.1 Tag Numbers for Electrical Cables shall be as follows:

24 – ELP – 0001

Area Code (See Appendix A) 4 Digit Sequential Number

Electrical Cable Code – LP (See Table 8)

11.4.1.2 The sequential numbers shall be unique for each group of cables having the same
Area Code and same cable code.

11.4.1.3 Cables that span two or more Areas shall inherit the location code from the originating
power source. i.e. from the location as shown on the cable schedules.

Doc. No.: QP-ENG-STD-013 Rev. 00 Date: 01/07/2019 Page 23 of 86

 QP STANDARD FOR EQUIPMENT IDENTIFICATION AND TAG
NUMBERING SYSTEM – DUKHAN FIELDS
DOC. No. QP-ENG-STD-013 Rev. 00

11.4.1.4 All cables shall be identified physically by have each end of the cable ferruled as
identified in this section.

Table 8: Electrical Cable Codes

DESCRIPTION REMARKS CABLE CODE

High voltage distribution > 650 VAC HD

Medium Voltage distribution 240 - 650VAC MD
Low voltage distribution < 240 VAC LD
High voltage power > 650 VAC HP
Medium Voltage Power 240 - 650 VAC MP
Low voltage power < 240 VAC LP
Direct current D.C. DP
Power control combined 415 V / 240 V AC PC
Control C
Lighting L
Earthing E
Cathodic protection CA
Trace Heating TRH

11.4.2 Identification of Electrical Single Core Cables

Single-core cables shall be identified as mentioned above with the additional suffix to
identify the phases as follows:

a) For Single-run cable per phase

24-ELP-0001 R (for R-Phase)

24-ELP-0001 Y (for Y-Phase)

24-ELP-0001 B (for B-Phase)

24-ELP-0001 N (for Neutral)

b) For Multi-run or more than one parallel run cable per Phase

24-ELP-0001 R1, 24-ELP-0001 R2 etc. (for R-Phase)

24-ELP-0001 Y1, 24-ELP-0001 Y2 etc. (for Y-Phase)

24-ELP-0001 B1, 24-ELP-0001 B2 etc. (for B-Phase)

24-ELP-0001 N1, 24-ELP-0001 N2 etc. (for Neutral)

Doc. No.: QP-ENG-STD-013 Rev. 00 Date: 01/07/2019 Page 24 of 86

 QP STANDARD FOR EQUIPMENT IDENTIFICATION AND TAG
NUMBERING SYSTEM – DUKHAN FIELDS
DOC. No. QP-ENG-STD-013 Rev. 00

11.4.3 Identification of Electrical Multi-Core Cables

a) For Single-run multi-core cable

24-ELP-0001

b) For Multi-run or more than one parallel run multi-core cables

Multi-run or more than one parallel run multi-core cable shall be identified as
mentioned above with the additional suffix as follows:

24-ELP-0001-1, 24-ELP-0001-2 etc.

11.4.4 Identification of Cable Joints

Cable joints shall be identified as power cable tags (as mentioned above) with the
additional suffix as given below:
30–EHP–0001R-CJ1

Power Cable Tag Cable Joint Sequence Number

24-EHP-0001R-CJ1 (for R-Phase)

24-EHP-0001Y-CJ1 (for Y-Phase)

24-EHP-0001B-CJ1 (for B-Phase)

11.4.5 Identification of Link Box Cables

Link boxes will be identified as below example:

30–EHP–0001R-LB1

Power Cable Tag Link Box Sequence Number

24-EHP-0001-LB1 (for CJ1)

24-EHP-0001-LB2 (for CJ2)

24-EHP-0001-LB3 (for CJ3)

11.5 Identification of Electrical Equipment in Wellhead Areas

For identification of electrical Equipment installed in Wellhead areas refer to section

(17.0)

11.6 Dukhan Power Supply and Substations

Due to the complex nature of the power supply arrangement following a typical
transmission and distribution philosophy, the tagging of the substations as well as the

Doc. No.: QP-ENG-STD-013 Rev. 00 Date: 01/07/2019 Page 25 of 86

 QP STANDARD FOR EQUIPMENT IDENTIFICATION AND TAG
NUMBERING SYSTEM – DUKHAN FIELDS
DOC. No. QP-ENG-STD-013 Rev. 00

equipment contained and associated with each substation should be carried out as per
the guidelines below:

11.6.1 Substation Tag Nos.

Sub Station Tags shall be as follows:

11.6.2 Equipment Tag Nos Associated with Sub Stations.

Equipment Tag Nos associated with Sub Stations shall be as follows:

Sample # 1
88-CB-0981-01-E90

Area Code (Appendix A)

Electrical Identifier for equipment

Associated Substation Serial Number

Equipment Serial Numbering/

Compartment

Busbar connection No.

(Vendor, i.e. ABB, SIEMENS, etc.)

Sample # 2
88-CB-0981-E90
88-VT-0981-E20
88-SIR-0981-06

Doc. No.: QP-ENG-STD-013 Rev. 00 Date: 01/07/2019 Page 26 of 86

 QP STANDARD FOR EQUIPMENT IDENTIFICATION AND TAG
NUMBERING SYSTEM – DUKHAN FIELDS
DOC. No. QP-ENG-STD-013 Rev. 00

11.6.3 Sample Tagging For Electrical Equipment inside Substation

11.6.3.1 For SCS & PMS (Substation Control System and Power Management System)
Example for “ZI” status signal:
88 – ZI – 0110 – nn

Area Code

Software Identifier

Associated Substation
Serial Number

Equipment Serial Numbering

Doc. No.: QP-ENG-STD-013 Rev. 00 Date: 01/07/2019 Page 27 of 86

 QP STANDARD FOR EQUIPMENT IDENTIFICATION AND TAG
NUMBERING SYSTEM – DUKHAN FIELDS
DOC. No. QP-ENG-STD-013 Rev. 00

12.0 IDENTIFICATION OF INSTRUMENTATION

12.1 Identification of Instrument Functions

12.1.1 The instrument function letters will be in accordance with Appendix B. Instrument
tagging codes are generally taken from ANSI/ISA-5.1-2009 Instrumentation Symbols
and Identification with minor amendments to cover Dukhan Tagging Requirements.
The list is not exhaustive, any request for additions must be conveyed to OE (D) in
writing with justification for approval and inclusion.

12.1.2 Instrument serial numbers shall be sequential by the first letter on the instrument
function code within the same area (Area Code), with the exception of gauges (LG, PG
and TG) and RO’S (restriction orifices) which are to be separately sequentially tagged.

12.1.3 Function letter codes for hand controllers shall be prefixed with the first letter of the
controlling function, e.g. PHC for pressure hand control, FHC for flow hand control etc.
The method used to indicate shutdown loop tags will be by using the double letter for
high, low etc. i.e. PSHH and PSLL.

12.1.4 An example of an instrument tag number is as follows:

24 – PIC – 0110

Area Code (See Appendix A) Unique Sequential Number

Instrument function letter code

(See Appendix B)

12.1.5 When requesting tags for use within a “loop” all instrument components within the loop
must be specified at the time of the request to avoid duplication. It is essential that a P
& ID be supplied at the same time of the request.

12.1.6 The Area Code should be placed outside each instrument tag bubble on P&ID’S,
alternatively a note shall be added to the drawing stating: - All instruments shall be
prefixed with xx (appropriate Area code or Well Type code and number see 12.1.9)
unless otherwise indicated. See Sample below:

12.1.7 Maintenance override switches shall be tagged HS, the recognition of maintenance
override shall be indicated outside the tag bubble on the P&IDs by adding the note
MOS.

12.1.8 For the position transmitting and indication control the tagging should be based on
respective valves e.g. SDV, BDV, FCV, etc. ‘ZIC’ and ‘ZT’ shall be suffixed at the end
of the valve as shown in the following example:
BDV: 23-BZIC-0001
SDV: 23-SZIC-0001

Doc. No.: QP-ENG-STD-013 Rev. 00 Date: 01/07/2019 Page 28 of 86

 QP STANDARD FOR EQUIPMENT IDENTIFICATION AND TAG
NUMBERING SYSTEM – DUKHAN FIELDS
DOC. No. QP-ENG-STD-013 Rev. 00

FCV: 23-FZIC-0001, etc.

Instrument Tag Nameplates shall be in accordance with ES-0-080104 - Template

Instrument Name Plates (7 Sheets). Users of this Standard shall use these templates
for development, design and procurement of instrument Tag Nameplates.

12.1.9 Identification of Instruments Installed on Wellheads

For identification of instrumentation installed in Wellhead refer to section (17.0)

12.1.10 Identification of Instrument Functions in Manifold Areas

For identification of instruments installed in Manifold areas see section (18.0)

12.2 Identification of Shutdown (Safety) Valves in Wellhead Areas

DK035 – SDV – 0101

Well Code & type code Sequential Number (Note)

(By Drilling Dept.)
(See Table 15 Section 17.0)

Instrument function letter code

Note: 101 to be used for SC-SSSV

102 to be used for SSV-1
103 to be used for SSV-2

SC-SSSV, SSV-1 and SSV-2 to be placed under the tag number in parenthesis
on the P& ID’s for clarification.

12.3 Identification of Instrument Multicore Cables

12.3.1 Identification of Instrument Cables is as follows:

12.3.2 The sequential number of the multicore cable should be the same as the sequential
number of the Junction box to which it is terminated. Where more than one multicore
cable is connected to a Junction box the cables shall be numbered as in the example
fig. 3 below:
Fig 3. Example of multicore cable numbering from a single junction box

Doc. No.: QP-ENG-STD-013 Rev. 00 Date: 01/07/2019 Page 29 of 86

 QP STANDARD FOR EQUIPMENT IDENTIFICATION AND TAG
NUMBERING SYSTEM – DUKHAN FIELDS
DOC. No. QP-ENG-STD-013 Rev. 00

12.3.3 Identification of Individual Signal Instrument Cables

Field cables from instruments to junction boxes are identified by giving the same
number as that of the instrument Tag.

Identification of telecommunications cable shall be in accordance with section (15.0)

of this Standard.

Table 9: Instrument Cable / Junction box codes

DESCRIPTION CODE

Alarm indication loop, i.e., alarms only no trips A

Control signals C
Data transmission i.e. Data Highway D
Electrical supply cables E
Fire and Gas F
Pneumatic P
Temperature ( Mv signals only) T
Special cables i.e. Fibre Optics X
Data Highway fibre optic. DX
Trip Signals SD

12.4 Instrument Junction Boxes

Instrument junction boxes are numbered in the same way as instrument cables, except
that the cable code (Table 9) is prefixed with ”IJB”. See example below:

24 – IJBE – 0001

12.5 Identification of Individual Signal Cores and Wires

12.5.1 All instrument cables and multicore cables shall have their cores ferruled at each end
with the terminal identification to which they are connected. Where considered
necessary these can be prefixed by the cable number.

12.5.2 Interface wires shall be clearly identified with ferrules indicating the source and
destination terminal details.

12.5.3 Wire identification within any system cabinet for systems like PLC, SCADA and DCS
and within system cabinet shall be based on Rack/Slot/Channel signal allocation and
terminal number, See Example below:
R4 S7 C5 01

Cabinet Rack 4 Cable Terminal 01

Cabinet Slot 7 Cabinet Channel 5

NOTE: Wire identification/software address TAGS within system cabinets are not
entered into SAP by Dukhan Maintenance Department, hence this section is issued for
guidance only.
Doc. No.: QP-ENG-STD-013 Rev. 00 Date: 01/07/2019 Page 30 of 86
 QP STANDARD FOR EQUIPMENT IDENTIFICATION AND TAG
NUMBERING SYSTEM – DUKHAN FIELDS
DOC. No. QP-ENG-STD-013 Rev. 00

12.6 Identification of Instrument Panels, Gauge Boards & Cabinets

12.6.1 Identification of Instrument Control Panels and Cabinets

Identification of Instrument Control Panels and cabinets is as follows:

Table 10: Panels / Cabinet Codes

DESCRIPTION CODE DESCRIPTION CODE
Auxiliary Control Panel ACP Main Distribution Frame MDF
Alarm Mimic Panel AMP Main System Cabinet MSC
Building Management
BMC Monitor (Viewing only) MNTR
Console
Continuous Emission Programmable Logic
CEMS PLC
Monitoring Panel Controller
Data Acquisition Recording
DARS Printer PRT
Panel
Emergency Shutdown Panel ESD Push Button Console PBC
Fire Alarm Panel FAP Remote Terminal Unit RTU
Fire and Gas Panel FGP Solar Control Panel SCP
Flow Computer Panel FCP Solar Module SOM
Interface Unit IFU Solar Monitor SOL
Interposing Relay Cabinet IRC Status Display System (F&G) SDS
Local Cabinet (see 12.6.2) LCP System Cabinet SCA
Local Gauge Board (see
LGB Tariff Meter Panel TMP
12.6.2)
Local Panel (see 12.6.2) LP Vibration Monitoring Panel VMP
Marshalling Cabinet MC Video Wall VW
Main Control Panel MCP Work Station WKS

12.6.2 Local Panels/Cabinets & Gauge Boards Associated with Specific Items of
Equipment

Where local panels and gauge boards are exclusively associated with Specific Items
of Equipment they shall be prefixed with the equipment items tag number. See example
below:

Note that local panels may be for control, alarm annunciation or other purposes.
Doc. No.: QP-ENG-STD-013 Rev. 00 Date: 01/07/2019 Page 31 of 86
 QP STANDARD FOR EQUIPMENT IDENTIFICATION AND TAG
NUMBERING SYSTEM – DUKHAN FIELDS
DOC. No. QP-ENG-STD-013 Rev. 00

12.6.3 Local Panels/Cabinets in Wellhead Areas

For identification of Local Panels/Cabinets installed in Wellhead refer to section (17.0)

12.6.4 Identification of Raceways

Raceways for cable routing are identified as follows:

24 – R E H – 300 – 01

Area Code (Appendix A) Sequential Raceway Number

R = Rack Width in mm
L = Ladder
T = Tray H = Very high disturbing
C = Channel D = Disturbing
I = Indifferent
E = Electrical S = Sensitive
I = Instrument V = Very Sensitive
J = Telecom

Doc. No.: QP-ENG-STD-013 Rev. 00 Date: 01/07/2019 Page 32 of 86

 QP STANDARD FOR EQUIPMENT IDENTIFICATION AND TAG
NUMBERING SYSTEM – DUKHAN FIELDS
DOC. No. QP-ENG-STD-013 Rev. 00

13.0 IDENTIFICATION OF HVAC ASSOCIATED MECHANICAL AND

ELECTRICAL EQUIPMENT
HVAC mechanical and electrical equipment will be assigned a prefix-using letter ‘H’ as
a primary identifier, as shown in Table 11. An example of the tag string is shown as
follows:
24 – HAC – 0001

Area Code 4 Digit Sequential Number

(See Appendix A)
Letter Code (Table 11)

Table 11: HVAC Mechanical and Electrical Equipment Codes

Description Code Description Code Description Code

Condenser &
Axial flow fan &
HAB Split A/C HCN Transfer Grill HGT
motor
(outdoor)
Air conditioning Refrigeration
HAC HCO Humidifier HHF
unit (Indoor) compressor
Air Supply HVAC control
HAD HCP Isolating Damper HID
Diffuser panel
Constant volume
Air Filter HAF reheat unit & HCU Induction Unit HIU
Chiller Unit
Air Handling Unit HAH Exhaust Fan HEF Heating coil-liquid HLH
Balancing Heating coil- Mixed flow fan &
HBD HEH HMB
Damper electric motor
Non-return
Air Washer HBF Evaporator HEV HND
damper
Constant Air Exhaust Fan Return Air
HCA HFC HRA
Volume Controller Register
Centrifugal fan &
HCB Fan Coil Unit HFCU Sound attenuator HSA
motor
Cooling Coil, Fire and Gas Terminal reheat
HCC HFD HTU
Liquid damper unit
Pressure control Gas Tight Volume control
HCD HGD HVD
damper Dampener damper
Moisture Extract/grill Water heater
HCF HGH HWH
eliminator diffuser (Calorifier)
HCL Supply/grill
Cyclone HGS Weather louver HWL
diffuser

Doc. No.: QP-ENG-STD-013 Rev. 00 Date: 01/07/2019 Page 33 of 86

 QP STANDARD FOR EQUIPMENT IDENTIFICATION AND TAG
NUMBERING SYSTEM – DUKHAN FIELDS
DOC. No. QP-ENG-STD-013 Rev. 00

14.0 IDENTIFICATION OF RESCUE AND SAFETY EQUIPMENT

Identification of Rescue and Safety Equipment is as follows:

Table 12: Rescue and Safety Equipment Codes

Description Code Description Code

Emergency Escape Breathing Fireman’s equipment
EEBA SFK
Apparatus (Portable) (Cabinet)
Wind Sock NWS Fire Tender SFT
Breathing Air Manifold RAM Fire extinguisher SFX
Emergency Door Release RDR Halon cylinder SHA
Breathing Air Cylinder RBA Hydrant Equipment SHE
Rescue equipment box REB Hose reel SHR
First Aid Kit RFA Halon skid SHS
Stretcher RST Hydrant SHY
Supply Air Breathing
SABA FM-200 Cylinder SMC
Apparatus
Self-Contained Breathing
SCBA Monitor SMO
Apparatus
CO2 cylinder SCC FM-200 Skid SMS
Safety Shower / Eyewash
Emergency Eyebath/ Eyewash SEB SSH
(Combined)
Safety Electrical Kit (Cabinet) SEK Emergency Shower SSR
Fire Blanket SFB

Doc. No.: QP-ENG-STD-013 Rev. 00 Date: 01/07/2019 Page 34 of 86

 QP STANDARD FOR EQUIPMENT IDENTIFICATION AND TAG
NUMBERING SYSTEM – DUKHAN FIELDS
DOC. No. QP-ENG-STD-013 Rev. 00

15.0 IDENTIFICATION OF TELECOMMUNICATIONS / SECURITY AND IT

EQUIPMENT
Telecoms / Security and IT Equipment shall be identified as follows:

24 – JXT – 0001

Area Code (See Appendix A) 4 Digit Sequential Number

Letter Code (Table 13)

Table 13: Telecoms / Security and IT Equipment Identification Codes

Description Code
Access Control System Controller JACC
Air Ground JAG
Flash Alarm Lamp JAL
Alarm Sounder JAS
Audio terminal outlet JATO
Telecommunications Junction Box Audio JBA
Telecommunications Battery Bank JBB
Building Management System JBMS
Baggage Scanner JBS
Telecommunications Junction Box JBX
Call Manager Server JCMS
Card Reader JCR
Single / Dual Reader Interface Module JCRI
Coaxial Cable JCX
Draw Pit (For Telecommunications Cables) JDP
Digital Distribution Frame JDDF
Electric Door Lock JDL
DVD Player JDVD
Exit Vehicle Approach Detection JEAD
Telecom Earth Bar JEB
Exit Break Glass Unit JEBG
Engineering Order Wire JEOW
Exit Push Button JEPB
Ethernet Switch JES
Intruder Alarm System Controller JIAC
Infrared Detector JID
Intermediate Distribution Frame JIDF
CCTV Camera Night Vision Infrared Illuminator JII
Intrusion Prevention Server JIPP
Intercom Station JIS
Keyboard, Video, Mouse Switch JKVMS
Door Magnetic Contact JMC
Telecommunications Main Distribution Frame JMDF
Amplifier JMA

Doc. No.: QP-ENG-STD-013 Rev. 00 Date: 01/07/2019 Page 35 of 86

 QP STANDARD FOR EQUIPMENT IDENTIFICATION AND TAG
NUMBERING SYSTEM – DUKHAN FIELDS
DOC. No. QP-ENG-STD-013 Rev. 00

Control System Processor JMCP

Document Camera JMDC
Mixer JMDSP
First Order Digital Multiplexer JMF
High Order Digital Multiplexer JMH
Hideaway Surface Access JMHSA
Modem JMM
Wireless Microphone System JMMS
Projector JMP
Intercom Master Station Exchange JMSE
Monitor Speaker JMSPR
Control Touch Screen JMTS
USB Extender JMUSB
Front Projection Screen JMSC
Optical Distribution Frame / Fiber Optic Path Panel JODF
Public Address Amplifier JPA
Private Automatic Branch Exchange JPABX
Public Address Access Unit / Control Panel JPC
Protocol Converter Unit JPCU
Power Supply / Distribution Unit JPSU
PDH Subrack JPSR
CCTV PTZ Assembly JPTZ
Volume Control JPVAC
Queue Management Main Display / Counter Display JQMD
Queue Management Main Server JQMS
Queue Management Ticket Dispenser JQMT
Queue Management Work Station JQMW
Radio Antenna JRA
Battery Charger JRBC
Radio Base Stations JRBS
Radio Beacon Transmitter JRBT
Radio Control Unit JRC
Radio Fixed JRF
Radio Hand Held JRH
Radio Microwave JRM
Radio Mobile JRMB
Router JROU
Radio Terminal JRT
Telecom Supervisory JS
SDH Equipment JSDH
SDH Subrack JSSR
In House Amplifier (TV Installation) JTIA
Out Door Amplifier (TV Installation) JTOA
Tap Off Boxes (TV Installation) JTTB
TV Outlet JTV
Local Craft Terminal JSWS
Telecom UPS Systems JUPS
Video Line Amplifier JVA

Doc. No.: QP-ENG-STD-013 Rev. 00 Date: 01/07/2019 Page 36 of 86

 QP STANDARD FOR EQUIPMENT IDENTIFICATION AND TAG
NUMBERING SYSTEM – DUKHAN FIELDS
DOC. No. QP-ENG-STD-013 Rev. 00

Audio Video Equipment See also JVA, JVC, JVLC, JVD for JVAE
specific related items.
Video Cross Bar (Exchange) JVC
Video Conference System JVCS
Video Decoder JVD
Video Decoder Subrack JVDSR
Video Encoder Subrack JVESR
Video Line Corrector JVLC
Wireless Access Point JWAP
Wireless LAN Controller JWLNC
Telecommunications Cable (JXX for fiber optic) JX
Arial / Antenna JXA
Arial/ Antenna couplers JXAC
Antenna Tower JXAT
Talk Back Equipment JXB
Camera Assembly / CCTV Camera JXC
CCTV Console / Controller JXCC
Video Streamer JXCE
CCTV Monitor JXCM
CCTV Server JXCS
CATV Rack JXCT
CCTV Thermal Camera JXCTH
ANPR Camera JXCR
CCTV Camera Wash Unit JXCW
Fibre Driver JXD
Digital Audio Systems JXDAS
Telecommunications Equipment Rack JXEQ
Fax Machine JXF
High Powered Loud Speaker JXH
Fibre Optic Transceiver JXIX
Fibre Optic Transceiver Subrack JXIXSR
Low powered Loud Speaker JXL
Medium powered Loud Speaker JXM
Patch Panel JXPP
Radar JXR
Remote Control(s) JXRC
Telephone Socket JXSK
Channel Switch JXS
Telephone JXT
Telephone Booth JXTA
Telephone Bell JXTB
Telephone explosion proof JXTE
Telephone Hood JXTH
Fiber Optic Terminal Equipment JXTL
Telephone Relay JXTR
Telephone Lamp or Beacon Flashing JXTS
Cable TV Antenna JXTV
Miscellaneous Telecommunications Equipment & Systems JXU

Doc. No.: QP-ENG-STD-013 Rev. 00 Date: 01/07/2019 Page 37 of 86

 QP STANDARD FOR EQUIPMENT IDENTIFICATION AND TAG
NUMBERING SYSTEM – DUKHAN FIELDS
DOC. No. QP-ENG-STD-013 Rev. 00

Data Storage System JXUD

Telecom Testing Equipment JXUT
CCTV Digital Video (DVI) Cable JXV
Voice Patch Panel JXVP
Telecom Fiber Optic Cables JXX
Fiber optic Cable Splice JXXS
Convertor JXY

Doc. No.: QP-ENG-STD-013 Rev. 00 Date: 01/07/2019 Page 38 of 86

 QP STANDARD FOR EQUIPMENT IDENTIFICATION AND TAG
NUMBERING SYSTEM – DUKHAN FIELDS
DOC. No. QP-ENG-STD-013 Rev. 00

16.0 IDENTIFICATION OF FIRE AND GAS DETECTION EQUIPMENT

16.1 Identification of Fire and Gas Equipment (As specified)
This section covers identification of Fire and Gas Equipment installed in:
a) Process Plants/Sub Stations (Field Mounted) single circuit (See 16.2)
b) Buildings/Living Quarters as Multi Circuits (See 16.3)
c) Buildings/Living Quarters as Single Circuits (See 16.4)
d) Dukhan Wellhead Areas (See 16.5)
Table 14: Fire and Gas Identification Codes

Description Code Description Code

Audible Alarm Visual AAVI Heat Detector Multi Sensor HDM
Indicator Combined
Air Sampling Unit ASU Heat Detector Rate of Rise HDR
Co2 Pre Discharge Audible High sensitivity smoke
COAA HSSD
Alarm detector
Co2 Pre Discharge Visual Fire Detection Interface Unit IFU
COVA
Alarm
Co2 Status Light COXL Manual Alarm Call Point MAC
Deluge Manual Release
DEL Oil Mist Detector OMD
Point
End Of Line Resistor EOL Portable Gas Detector PGD
Electro Magnetic Device ES Smoke Detector Aspirated SDA
Flame Detector (IR) FDI Smoke Detector Ionisation SDI
Smoke Detector SDIO
Flame Detector Ultra Violet FDU
Infrared/Optical combined
Flame Detector Ultra FDUI Beam Controller SDIOC
Violet/IR Combined
Fire Monitor FM Smoke Detector (IR) SDIR
Flame Smoke Detector FSD
Smoke Detector (Optical) SDO
Combined
Flashing Beacon Combined FBA Smoke Detector (Photocell) SDP
with Audible alarm
Smoke Emitter Beam SEBD
Audible alarm GAA
Detector
Gas Detector Audible Smoke Image Beam SIBD
GDA
(Ultrasonic) Detector (Receiver)
Gas Detector Flammable GDF Siren SIR
Gas Detector Toxic (H2S) GDT Bell SL
Visual alarm (Flashing
GVA Lamp (On Panel) XL
Beacon)
Heat Detector (Rate
HDC
Compensated)
Heat Detector Fixed (Temp.) HDF
Doc. No.: QP-ENG-STD-013 Rev. 00 Date: 01/07/2019 Page 39 of 86
 QP STANDARD FOR EQUIPMENT IDENTIFICATION AND TAG
NUMBERING SYSTEM – DUKHAN FIELDS
DOC. No. QP-ENG-STD-013 Rev. 00

16.2 Identification of Fire and Gas Detection Devices Installed as Individual

Circuits in Process Plants/Sub Stations

16.2.1 Identification of Fire and Gas Detection Devices Installed in Process Plants/Sub
Stations shall be as follows:
24-GDT-03-0001

Area Code (Appendix A) 4 digit Sequential serial number

Device code (Table 14) Fire Zone No. 2 digit or Sub

Station Sequential Number

16.2.2 Serial numbers will be unique in each group of devices having the same Area code the
same device code and the same fire zone number or Sub Station sequential number.

16.2.3 Example of Smoke Detector installed in substation 24-SS-4101 would be as follows:

24-SDO-4101-01/01

24-SDO-4101-01/02 etc.

16.3 Identification of Fire and Gas Detection Devices Installed in Buildings/ Living
Quarters as Multi-Circuits per Fire Zone
16.3.1 Identification of Fire and Gas Detection Devices installed in Buildings/Living Quarters
as Multi-Circuits per Fire Zone shall be as shown in the following example:

24 - SDO - *0024-03-01-01

Area Code (Appendix A) Device order in circuit

Device Code (Table 14) Circuit number

*Sequence Number of Fire and Zone identification

Gas Panel

The above example indicates a line monitoring circuit connected to Fire and Gas Panel
Tagged 24-FGP-0024. Refer to Section (12.6).
* For Buildings outside Plant Battery Limits this sequence number will be that for the
Fire Alarm Panel (See Section 12.6 Table 10)

16.3.2 The fire zone identification shall be a two digit identifier starting at 01 and rising in
increments of one for each classified fire zone area.

16.3.3 The circuit identification shall be a two-digit identifier starting at 01 and rising in
increments of one for each separate circuit chain. Note that Each Fire and Gas Panel
or Fire Alarm Panel will have its own set of individual circuits. The first device in the
circuit will be suffixed 01 the second 02 etc. The last device in line monitoring circuits
will be suffixed with the letters EOL to identify the fitted end of line resistor.

Example: 24-SDO- 0024-03- 01-12-EOL

Doc. No.: QP-ENG-STD-013 Rev. 00 Date: 01/07/2019 Page 40 of 86
 QP STANDARD FOR EQUIPMENT IDENTIFICATION AND TAG
NUMBERING SYSTEM – DUKHAN FIELDS
DOC. No. QP-ENG-STD-013 Rev. 00

16.4 Identification of Fire and Gas Detection Devices Installed in Buildings/Living

Quarters as Single Circuits per Fire Zone

Identification of Fire and Gas Detection Devices installed in Buildings/Living Quarters

as Single Circuits per Fire Zone is identical to Multi-Circuit line monitoring as shown in
section (16.3) with the omission of the Circuit Number as show in the following
example:
24 - SDO - *0024-03-01

Area/Plant Code Device order in circuit

(Appendix A)

Device Code (Table 14) Zone identification

*Sequence Number of Fire and

Gas Panel

The above example indicates a line monitoring circuit connected to Fire and Gas Panel
Tagged 24-FGP-0024. Refer to Section (12.6).

* For Buildings outside Plant Battery Limits this sequence number will be that of the
Fire Alarm Panel (See Section 12.6 Table 10)

16.5 Identification of Fire and Gas Devices in Wellhead Areas:

See section 17.0 for Fire and Gas Devices installed in Wellhead areas.

16.6 Identification of Fire and Gas Cables, Junction Boxes, Panels and Cabinets

16.6.1 For Fire and Gas Cables see to section (12.3)

16.6.2 For Fire and Gas Junction Boxes see to section (12.4)

16.6.3 For Fire and Gas Panels see to section (12.6).

Doc. No.: QP-ENG-STD-013 Rev. 00 Date: 01/07/2019 Page 41 of 86

 QP STANDARD FOR EQUIPMENT IDENTIFICATION AND TAG
NUMBERING SYSTEM – DUKHAN FIELDS
DOC. No. QP-ENG-STD-013 Rev. 00

17.0 IDENTIFICATION OF EQUIPMENT INSTALLED IN WELLHEADS

17.1 The below example is typical for equipment installed in Wellheads. The scope of
equipment and actual tags are detailed in Appendix E1, E2, F, G, H, I1, I2, and I3 for
Well Types. The Appendices are supplemented by typical standard P&ID AutoCAD
templates as defined below:

DK035 – ABC – XXX

Well Type and Well number Standard sequential number

(By Drilling See Table 15) (See Appendix E1, E2, F, G, H, I1, I2, I3)

Equipment Letter Code

(See Appendix E1, E2, F, G, H, I1, I2, I3)

17.2 The Equipment installed Wellheads are set as standard. Users of this Standard shall
complete the listing of standard allocated tag numbers by inserting the appropriate Well
type code and well Number on the template (See Appendix E1, E2, F, G, H, I1, I2, and
I3). The same shall be submitted with the applicable Tag request. Native file formats
of these templates are available from Operations Engineering OEE (D) on request.

17.3 AutoCAD Standard Templates of Typical Tags for Wellhead P&ID’s are illustrated as
below:
Appendix J1 - Typical P&ID Wellhead PWI Wells Type 1 Pressure bleed line with
GLV valves
Appendix J1 - Typical P&ID Wellhead PWI Wells Type 2 Pressure bleed line with
BV valves
Appendix K - Typical P&ID Wellhead Gas Lift Wells
Appendix L - Typical P&ID Wellhead Water Source Wells
Appendix M - Typical P&ID Wellhead Re-Circulation Wells
Appendix N1 - Typical P&ID Wellhead Type 1 With Hydraulic Wellhead Control
Panel, Pressure bleed line with GLV valves
Appendix N2 - Typical P&ID Wellhead Oil Wells – Type 2 With Hydraulic Wellhead
Control Panel, Pressure bleed line with BV valves
Appendix N3 - Typical P&ID Wellhead Oil Wells – Type 3 Without Hydraulic
Wellhead Control Panel, Pressure bleed line with BV valves
Table 15: Well Type Codes

WELL DESCRIPTION WELL TYPE CODE STATUS *

Oil or water injection, Gas Operations (Arab
DK Preferred
“D” Recycle Gas)
Disposal DKD Preferred
Khuff Gas DKG Preferred
Water source DKW Preferred
Water Recycle DKWR Preferred
Water supply DKWW Preferred

Doc. No.: QP-ENG-STD-013 Rev. 00 Date: 01/07/2019 Page 42 of 86

 QP STANDARD FOR EQUIPMENT IDENTIFICATION AND TAG
NUMBERING SYSTEM – DUKHAN FIELDS
DOC. No. QP-ENG-STD-013 Rev. 00

18.0 IDENTIFICATION OF EQUIPMENT INSTALLED IN MANIFOLD AREAS

Manifold equipment will be prefixed and associated Manifold Number. Example of the
tag string are shown in sections (18.1 and 18.2). Tagging of Extended Oil Manifolds
are identified in section (18.3)

Note:

For the stand alone facilities outside from the stations, will be numbered according to
Table 16 and 17

18.1 Gas Lift Manifold Equipment Tagging

18.1.1 Gas Lift Manifold Pipeline Tagging

12-4020-0001-6”-GP

Manifold Number Line allocated number

(Table 16) (See 9.0 Table 3)

Doc. No.: QP-ENG-STD-013 Rev. 00 Date: 01/07/2019 Page 43 of 86

 QP STANDARD FOR EQUIPMENT IDENTIFICATION AND TAG
NUMBERING SYSTEM – DUKHAN FIELDS
DOC. No. QP-ENG-STD-013 Rev. 00

Table 16: Gas Lift Manifold Numbers

MANIFOLD
SECTOR LOCATION and Tag NUMBER
NUMBER
12-4020 FAHN LIFT GAS MANIFOLD STATION 12-A-4020
12-4021 FAHN LIFT GAS MANIFOLD STATION 12-A-4021
13-4031 FAHS LIFT GAS MANIFOLD STATION 13-A-4031
13-4032 FAHS LIFT GAS MANIFOLD STATION 13-A-4032
FAHAHIL 13-4033 FAHS LIFT GAS MANIFOLD STATION 13-A-4033
13-4034 FAHS LIFT GAS MANIFOLD STATION 13-A-4034
14-5227 FAHM LIFT GAS MANIFOLD STATION 14-A-5227
14-5228 FAHM LIFT GAS MANIFOLD STATION 14-A-5228
14-5229 FAHM LIFT GAS MANIFOLD STATION 14-A-5229
22-4201 KAHN LIFT GAS MANIFOLD STATION 22-A-4201
22-4202 KAHN LIFT GAS MANIFOLD STATION 22-A-4202
22-4203 KAHN LIFT GAS MANIFOLD STATION 22-A-4203
22-4204 KAHN LIFT GAS MANIFOLD STATION 22-A-4204
22-4205 KAHN LIFT GAS MANIFOLD STATION 22-A-4205
23-4719 KAHS LIFT GAS MANIFOLD STATION 23-A-4719
KHATIYAH
23-4720 KAHS LIFT GAS MANIFOLD STATION 23-A-4720
23-4721 KAHS LIFT GAS MANIFOLD STATION 23-A-4721
23-4722 KAHS LIFT GAS MANIFOLD STATION 23-A-4722
24-5227 KAHM LIFT GAS MANIFOLD STATION 24-A-5227
24-5228 KAHM LIFT GAS MANIFOLD STATION 24-A-5228
24-5229 KAHM LIFT GAS MANIFOLD STATION 24-A-5229
31-4919 JALM LIFT GAS MANIFOLD STATION 31-A-4919
31-4920 JALM LIFT GAS MANIFOLD STATION 31-A-4920
31-4921 JALM LIFT GAS MANIFOLD STATION 31-A-4921
JALEHA
31-4922 JALM LIFT GAS MANIFOLD STATION 31-A-4922
31-4923 JALM LIFT GAS MANIFOLD STATION 31-A-4923
31-4001 JALM LIFT GAS MANIFOLD STATION 31-A-4001
DIYAB 32-4002 DIYAB GAS LIFT MANIFOLD
GAS
Arab D Tie-in LIFT GAS MANIFOLD STATION 23-
OPERATIONS 23-4731
A-4731
- (Arab D)

Doc. No.: QP-ENG-STD-013 Rev. 00 Date: 01/07/2019 Page 44 of 86

 QP STANDARD FOR EQUIPMENT IDENTIFICATION AND TAG
NUMBERING SYSTEM – DUKHAN FIELDS
DOC. No. QP-ENG-STD-013 Rev. 00

18.2 Oil Manifold Equipment Tagging

18.2.1 Oil Manifold Pipeline Tagging

31-MAN-001-0001-6”-GP

Manifold Number Line allocated number

(Table 17) (See 9.0 Table 3)

18.3 Extended Oil Manifold Equipment Tagging

12-M1-PT-0001

Extended Manifold Number Sequential allocated number

(Table 17)

Equipment Alpha Code

18.3.1 Extended Oil Manifold Pipeline Tagging

12-M1-0001-6”-GP

Extended Manifold Number Line allocated number

(Table 17) (See 9.0 Table 3)

Doc. No.: QP-ENG-STD-013 Rev. 00 Date: 01/07/2019 Page 45 of 86

 QP STANDARD FOR EQUIPMENT IDENTIFICATION AND TAG
NUMBERING SYSTEM – DUKHAN FIELDS
DOC. No. QP-ENG-STD-013 Rev. 00

Table 17: Oil Manifold Numbers

EXTENDED
MANIFOLD
MANIFOLD LOCATION
NUMBER
NUMBER
12-M1 12-MAN-001 MANIFOLD AREA (FAHN)
13-M1 13-A-MAN-001 MANIFOLD AREA (FAHS)
14-M1 14-A-MAN-001 MANIFOLD AREA EAST SIDE (FAHM)
14-M2 14-A-MAN-002 MANIFOLD AREA WEST SIDE (FAHM)
22-M1 22-MAN-001 MANIFOLD AREA WEST SIDE (KAHN)
22-M1 22-MAN-001 MANIFOLD AREA EAST SIDE (KAHN)
22-M1 MANIFOLD-I ADDITIONAL OIL INLET MANIFOLDS : 1 (KAHN)
22-M2 MANIFOLD-II MANIFOLD AREA EAST SIDE (KAHN)
23-M1 23-MAN-A-001 MANIFOLD AREA (KAHS)
24-M1 24-A-MAN-001 WEST MANIFOLD
24-M2 24-A-MAN-002 WEST MANIFOLD
24-M3 24-A-MAN-003 WEST MANIFOLD
24-M4 24-A-MAN-004 EAST MANIFOLD
24-M5 24-A-MAN-005 EAST MANIFOLD
31-M1 31-A-MAN-001 EAST MANIFOLD (JALM)
31-M2 31-A-MAN-002 SOUTH MANIFOLD
31-M3 31-A-MAN-003 NORTH MANIFOLD
32-M1 - OIL INLET MANIFOLD SKID NO: 1 (DYAB)
32-M2 - OIL INLET MANIFOLD SKID NO: 2 (DYAB)
32-M3 - OIL INLET MANIFOLD SKID NO: 3 (DYAB)

19.0 IDENTIFICATION OF MOBILE EQUIPMENT

19.1 The tagging of mobile equipment as designated here is not compulsory if the Asset
Holder is having their own database and numbering system for mobile equipment.

19.2 Mobile Equipment shall be identified as department wise ownership by prefixing the
equipment letter code by department code. See Table 18.

Table 18: Department Codes

CODE DEPARTMENT
OBM Maintenance Services
OED Operation Engineering
OND Operations North
OSD Operations South
OGD Gas Operations
UDN Drilling
FMK Facilities Management
OHD Health, Safety & Environment

19.3 Equipment Letter codes for mobile equipment shall be made up of equipment letter
codes defined throughout this Standard by prefixing the code with letter M, other

Doc. No.: QP-ENG-STD-013 Rev. 00 Date: 01/07/2019 Page 46 of 86

 QP STANDARD FOR EQUIPMENT IDENTIFICATION AND TAG
NUMBERING SYSTEM – DUKHAN FIELDS
DOC. No. QP-ENG-STD-013 Rev. 00

specific letter codes are defined in Table 19 as below .Example of mobile equipment
tag is shown in the following example:

OED - MDG- 0001

Department Ownership Sequential allocated number

*Mobile Equipment Letter Code

*Code is derived from codes in this Standard with addition of Prefix M, other specific
codes (not included in this Standard) are shown in Table 19 below.

19.4 For Mobile skids (OED-MA-0001) only the skid will be tagged and not the internal
components.

Table 19: Specific Mobile Equipment Letter Codes

DESCRIPTION CODE DESCRIPTION CODE
MISCELLANEOUS
Engine Diesel MDG Main Distribution Board MMDB
Fan/ Air Jet MFN Mobile Genset MGN
Receiver Pig MPR Survey Equipment MSURV
Launcher Pig MPL
WORK SHOP EQUIPMENT’S
Welding Machine MMW Screw Threading STM
Plasma Cutting Machine MMCU Vertical Boring Machine VBM
Flange Facing Grooving
Electrode Oven/ Oven MEO FFGM
Machine
Drill Sharpener MDS Portable Workshop MPW
Manual Press MMP Mobile Lighting Tower MLTT
Drill Machine DMS Miscellaneous MWE
VEHICLES
Mobile Drum Crusher Club Car/ Golf Cart MCLB
Mobile Expandable Office
Ambulance
Trailer
Workshop Mobile Mass Casualty Vehicle
Mobile Medical Equipment MERV
Sc P/Up 3 T
Carrier
8,000 G. Oil MCV Breakdown Truck
Skip Truck Mobile Medical Clinic
Skip Truck 6x4 Fire Tractor Head
4wd Jib Crane 6t Foam Tender
MFFV
4x4l Self Loader Angus Portable Foam Tank
8x4 Self Loader Foam/Water/Dcp Fire Tender

Doc. No.: QP-ENG-STD-013 Rev. 00 Date: 01/07/2019 Page 47 of 86

 QP STANDARD FOR EQUIPMENT IDENTIFICATION AND TAG
NUMBERING SYSTEM – DUKHAN FIELDS
DOC. No. QP-ENG-STD-013 Rev. 00

4x4 L Self Loader Foam Pumper

Self Loader Commander
Self Loader Truck 4x4 Fire Tender
Shovel Fire Truck
Dump Truck B.A. Trolley
Fire Tender Ladder Platform
Riv Scania
Hazmat Vehicle
Fire Command Vehicle
Forklift Drum Carrier Fire Water Tanker
Forklift (Manual/ Electric) Tank Trailer
Godrej F/Lift-Core Store Trailer F/B, Lowbed
Pallet Truck (Manual/
MFLFT Emergency Desert Trailer
Electric)
MTRL
Pallet Stracker/ Side Loader Trailer Nitrogen/ Diesel/
Forklift Chemical Liquids
Pallet Fork Lifter Semi Hydraulic Tipper Trailer
Pedestrian Pallet Truck Vacuum Tanker Trailer
Powered Sweeper Diesel Tanker
Mobile Ablution Facility Hilift-Truck
Street Sweeper Truck Highlift Aerial Platform Truck
Industrial Sweeper Truck Narrow Aisle Truck
Sand Cleaner, Surf Rake MSAN Hyster/ Atlet Reach Truck MTRK
Environmental Sampling Van Truck
Mobile Service Van MSVC Tractor Head
Flatbed Truck Vacuum Tanker
MFLB
Flatbed Pick Up Water Tanker

20.0 IDENTIFICATION OF LABORATORY EQUIPMENT

All Laboratory equipment is assign Alpha code for all ‘LAB.’ Example of the tag string
is shown as follows:

Doc. No.: QP-ENG-STD-013 Rev. 00 Date: 01/07/2019 Page 48 of 86

 QP STANDARD FOR EQUIPMENT IDENTIFICATION AND TAG
NUMBERING SYSTEM – DUKHAN FIELDS
DOC. No. QP-ENG-STD-013 Rev. 00

21.0 IDENTIFICATION OF EQUIPMENT IN HOUSING

21.1 The tagging for internal Housing equipment shall use the same alpha codes specified
in this Standard but shall be prefixed and associated with the House number and Flat
number as required. Same equipment items in the building will be a sequential suffix
(Unit Number) 01, 02, 03 etc.

21.2 An example of the tag string is shown as follows:

88 – 2500 – 1 – HAC - 01

Area Code Sequential Unit number

House Number Equipment Letter Code

Flat Number

Note:

For housing such has: Bungalow, Duplex House, and alike i.e. without “Flat number”
the equipment will be numbered as above by omitting Flat number.

All items of equipment inside the housing shall be assigned internally by the Project
team/Asset Holder as applicable in accordance with the above format.

22.0 IDENTIFICATION OF BUILDINGS

Buildings will be identified with Tag Number as in the following example:

14-BCR-0001

Area Code (Appendix A) Sequential allocated number

Building Code (Table 20)

Doc. No.: QP-ENG-STD-013 Rev. 00 Date: 01/07/2019 Page 49 of 86

 QP STANDARD FOR EQUIPMENT IDENTIFICATION AND TAG
NUMBERING SYSTEM – DUKHAN FIELDS
DOC. No. QP-ENG-STD-013 Rev. 00

Table 20: Building Identification Codes

DESCRIPTION CODE
Air Compressor Building BAC
Parking Bay Shed BCP
Central Control Building BCR
Chemical Storage Shed BCS
Colling Tower Structure BCW
Gate / Guard House BGH
Generator Shed BGS
Lay down Area BLA
Mosque BMQ
Workshop BMW
Pump Station BPH
Storage Building, Ware House BST
Telecom/Telemetry Building BTE
Miscellaneous Building/Shelter BMB
Equipment Building/Room BER

23.0 IDENTIFICATION OF CIVIL COMPONENTS

Identification of Civil Components shall be identified as defined in the examples shown
in the following sub-sections. Table 22 lists all Civil Component Codes

23.1 Tagging of Civil Components in General Areas

Tagging of Civil Components in general areas shall be tagged as below:

14-UGF-0001

Area Code (Appendix A) Sequential allocated number

Civil Component (Table 21)

23.2 Tagging for Civil Component Inside Buildings

Civil components inside buildings will be tagged by prefixing the building to the Civil
component codes (Table 21) and use a sequential suffix, 1, 2, 3 etc. as seen in the
below example.
14-BCR-0001 -UDFS1

Building Tag Number Civil Component (Table 21 with

Suffix No. 1)
23.3 Tagging for Civil Component in Manifolds

Civil components in Manifolds AREAS will be tagged by prefixing the civil component
tag with the manifold number, see section (18 Table 16, 17)) as shown in the
following example:

Doc. No.: QP-ENG-STD-013 Rev. 00 Date: 01/07/2019 Page 50 of 86

 QP STANDARD FOR EQUIPMENT IDENTIFICATION AND TAG
NUMBERING SYSTEM – DUKHAN FIELDS
DOC. No. QP-ENG-STD-013 Rev. 00

12-4020-UGF-0001

Manifold Number (18) Sequential allocated number

Civil Component (Table 21)

23.4 Tagging for Civil Component in Wellhead Areas

Civil components in Wellhead areas will be tagged by prefixing the civil component tag
with the Well type and well number as shown in the below example.
DKW075 – UGF – 101

Well Type and Well number Sequential number

(By Drilling, See Table 15 Section 17.0)

Civil Component (Table 21)

Table 21: Civil Components

DESCRIPTION CODE
Doors
Aluminum Door (with or without glazing) including all door accessories UDA
Steel Door including all door accessories UDS
Wooden Door including all door accessories UDW
Fire Rated Steel Door including all door accessories UDFS
Fire Rated Wooden Door including all door accessories UDFW
Door - Others Types UDZ
Windows
Wooden Window UWIW
Aluminum Window including glazing, blind, curtain and all window UWIA
accessories
Window – Others UWIZ
Floor
Floor with Tiled Finishes (e.g. ceramic tile, terazzo, marble & etc.) UFT
Floor with Vinyl Tile Finish UFV
Floor with Carpet Finish UFC
Floor with Epoxy Finish UFE
Floor with Wooden/Timber Strip Finish UFW
Floor with Cement Render Finish UFCR
Raised Floor System UFR
Floor with Steel Checker Plate UFCP
Floor with Steel Grating UFGR
Floor – Others UFZ
Wall
Concrete Wall - No Finish UWCO
Plastered Wall - No Other Finish UWPL
Wall with Paint Finish UWPT
Wall with Wall Paper Finish UWWP
Doc. No.: QP-ENG-STD-013 Rev. 00 Date: 01/07/2019 Page 51 of 86
 QP STANDARD FOR EQUIPMENT IDENTIFICATION AND TAG
NUMBERING SYSTEM – DUKHAN FIELDS
DOC. No. QP-ENG-STD-013 Rev. 00

Wall with Wooden/Timber Panel Finish UWWT

Gypsum Board Wall UWGY
Cladding Sheet Wall UWCL
Wall with Tile Finish UWT
Wall – Others UWZ
Ceiling & Finishes
False Ceiling - Gypsum Board Plaster Ceiling UCGY
False Ceiling - Metal Strip Finish UCMS
False Ceiling - Suspended Panel Type (e.g. gypsum, metal & etc.) UCSP
Ceiling - Others UCZ
Roof
Concrete Roof including fascia & water proofing. URCO
Fabric Canopy Roof including all fixing accessories URCA
Metal Cladding Roof URCL
Roof - Others URZ
Kitchen / Pantry Items
Kitchen/Pantry Cabinet including top & bottom units UKC
Kitchen/Pantry - Others UKZ
Box / Cabinet
PTW Cabinet/Box UBP
Key Isolation Box UBKI
Key Cabinet/Box UBKE
Fire Hose Reel Box UBHR
Fire Extinguisher Box UBFE
Cabinet / Box - Others UBZ
Gate & Fencing
Gate including single/double, emergency gates & all gate accessories BGT
Chain Link Fence including post, sand netting and all fencing UGF
accessories
Other Fencing UFN
Taps and Mixers
Chrome Plated / Brass Tap UBT
Shower Rose including mixer USR
Wash Hand Basin Mixer UMW
Bidet including hose & accessories UB
Sink Mixer UMS
Tap & Mixer - Others UTZ
Others
All type of boards include notice/sign board, picture frame, H2S card UOB
board, etc.
Concrete Foundation UCF
Culvert for Pipeline & drainage (A,B) UDC
Hand Rail UHR
Chain Barrier, Security Block USB
Access Ladder UAL
Wind Sock including Pole and Wind Sock NWS

Doc. No.: QP-ENG-STD-013 Rev. 00 Date: 01/07/2019 Page 52 of 86

 QP STANDARD FOR EQUIPMENT IDENTIFICATION AND TAG
NUMBERING SYSTEM – DUKHAN FIELDS
DOC. No. QP-ENG-STD-013 Rev. 00

Cable Marker UCM

Cable Trench UCT
Concrete kerb including painting UOK
Asphalt road including road marking UOR
Bollard (steel/plastic) including painting UOP
Crash Barrier (metal, concrete) UCB
Soakaway including soak pit, gully pot & drainage pipes USD

24.0 IDENTIFICATION SEWAGE TREATMENT PLANT SPECIALISED

EQUIPMENT
Equipment installed in Sewage Treatment Plants shall be tagged as defined above in
this Standard. In addition Table 22 Identifies other specialised equipment associated
with sewage treatment plant not already covered in this Standard as shall be tagged
as in the below example:

14-SBR-0001

Area Code (Appendix A) Sequential allocated number

Specialized Equipment
(Table 22)

Table 22: Sewage Treatment Plant Specialised Equipment

DESCRIPTION CODE
AEROBIC SLUDGE DIGESTER ASD
SBR DECANTER DEC
GRIT CLASSIFIERS GC
INLET CHAMBER ICH
SCREENING WASHING & COMPACTOR MXS
PARSHALL FLUME PF
SEQUENCE BATCH REACTORS SBR
SEQUENCING BATCH REACTOR BASINS SBRB
SLUDGE DRYING BEDS SDB
SLUDGE DEWATERING SDG
MANHOLE UMH
PEN STOCK UPK
UV DISINFECTION UNIT UVU
VORTEX GRIT TRAP VG

Doc. No.: QP-ENG-STD-013 Rev. 00 Date: 01/07/2019 Page 53 of 86

 QP STANDARD FOR EQUIPMENT IDENTIFICATION AND TAG
NUMBERING SYSTEM – DUKHAN FIELDS
DOC. No. QP-ENG-STD-013 Rev. 00

25.0 LIST OF APPENDICES

APPENDIX A : DUKHAN AREA CODES

APPENDIX B : INSTRUMENT FUNCTION CODES
APPENDIX C : TAG REQUEST / ADVICE FORM
APPENDIX D : REQUEST FOR VARIANCE TO STANDARD
APPENDIX E1 : STANDARD EQUIPMENT TAGS - PWI WELLS – TYPE 1
PRESSURE BLEED LINE WITH GLV VALVES
APPENDIX E2 : STANDARD EQUIPMENT TAGS - PWI WELLS – TYPE 2
PRESSURE BLEED LINE WITH BV VALVES
APPENDIX F : STANDARD EQUIPMENT TAGS – GAS LIFT WELLS
APPENDIX G : STANDARD EQUIPMENT TAGS – WATER SOURCE WELLS
APPENDIX H : STANDARD EQUIPMENT TAGS – RE-CIRCULATION WELLS
APPENDIX I1 : STANDARD EQUIPMENT TAGS – OIL WELL – TYPE 1 WITH
HYDRAULIC WELLHEAD CONTROL PANEL, PRESSURE
BLEED LINE WITH GLV VALVES
APPENDIX I2 : STANDARD EQUIPMENT TAGS – OIL WELL – TYPE 2 WITH
HYDRAULIC WELLHEAD CONTROL PANEL, PRESSURE
BLEED LINE WITH BV VALVES
APPENDIX I3 : STANDARD EQUIPMENT TAGS – OIL WELL – TYPE 3
WITHOUT HYDRAULIC WELLHEAD CONTROL PANEL,
PRESSURE BLEED LINE WITH BV VALVES
APPENDIX J1 : POWER WATER INJECTION – TYPICAL WELLHEAD (TYPE 1)
P&ID
APPENDIX J2 : POWER WATER INJECTION – TYPICAL WELLHEAD (TYPE 2)
P&ID
APPENDIX K : GAS LIFT WELL – TYPICAL WELLHEAD (WITHOUT WHCP)
P&ID
APPENDIX L : WATER SOURCE WELL – TYPICAL WELLHEAD P&ID
APPENDIX M : RE-CIRCULATION WELL – TYPICAL WELLHEAD P&ID
APPENDIX N1 : OIL WELL – TYPICAL WELLHEAD (TYPE 1) P&ID
APPENDIX N2 : OIL WELL – TYPICAL WELLHEAD (TYPE 2) P&ID
APPENDIX N3 : OIL WELL – TYPICAL WELLHEAD (TYPE 3) P&ID

Doc. No.: QP-ENG-STD-013 Rev. 00 Date: 01/07/2019 Page 54 of 86

 QP STANDARD FOR EQUIPMENT IDENTIFICATION AND TAG NUMBERING SYSTEM – DUKHAN FIELDS

DOC. No. QP-ENG-STD-013 Rev. 00

APPENDIX A: DUKHAN AREA CODES

1st 2nd 1st 2nd 1st 2nd
LOCAT ION NUMBER LOCAT ION CODE AND DESCRIPTION LOCAT ION NUMBER LOCAT ION CODE AND DESCRIPTION LOCAT ION NUMBER LOCATION CODE AND DESCRIPTION
CHARACTER CHARACTER CHARACTER CHARACTER CHARACTER CHARACTER
1 Fahahil 1 FHSP : Fahahil Stripping Plant CONTINUATION CONTINUAT ION
1A FSWPSA : Fahahil SP Potable Water Pump Station A 5 Miscellaneous 0 Whole Plot Areas 8 Dukhan Facilities 5D Dukhan Non-QP Housing
FAHN : Fahahil North 1 Equipment on Trunk lines 5E Landscaping Areas
FAHNM1 (FAHN Lift Gas Manifold Station 12-A-4020) 5 KSFSS : Khatiyah Main/ North FG Supply Station 5F Doha Bank Areas
2 FAHNM2 (FAHN Lift Gas Manifold Station 12-A-4021) A DSFG5A : Valve Station A (WHTP-A) 5G Heritage Mosque
FAHN : Manifold Area B DSFG5B : Valve Station B (WHTP-B) All facilities located at QP Concession areas outside Oil & Gas
6 Plants, Township and located between Dukhan - Ummbab Road and
FAHN : Additional Oil Inlet Manifolds D DSFG5D : Valve Station D (WHTP-D) West Shore; as follows:
FAHS : Fahahil South E DSFG5E : Valve Station E (KN-MP) 6A DECC : Dukhan Electrical Control Center
FAHSM1 (FAHS Lift Gas Manifold Station 13-A-4031) F DSFG5F : Valve Station F(FLGCS) 6B DMSS : Dukhan Main Intake Switching Station
FAHSM2 (FAHS Lift Gas Manifold Station 13-A-4032) G DSFG5G : Valve Station G (WHTP-G/E) PFC-DMSS (86C-BU-0001) : Power Factor Correction
3 6C
FAHSM3 (FAHS Lift Gas Manifold Station 13-A-4033) H DSFG5H : Valve Station H (FNFIS) (PFC Capacitor Bank) Building at DMSS

FAHSM4 (FAHS Lift Gas Manifold Station 13-A-4034) J DSFG5J : Valve Station J (FSDS) 6D QPAA : QP Administration Area
FAHS : Manifold Area DSFG5K : Valve Station K QPSFA : QP Support Facilities Area
K
FAHM : Fahahil Main (Desalination Fuel Gas Supply Station) SFAVI : Service Facilities Area Vehicle Inspection
6E
FAHMM1 (FAHM Lift Gas Manifold Station 14-A-5227) L DSFG5L : Valve Station L (WHTP-L/H)
SFAEES : Service Facilities Area Emergency Equipment Storage
FAHMM2 (FAHM Lift Gas Manifold Station 14-A-5228) M DSFG5M : Valve Station M
4
FAHMM3 (FAHM Lift Gas Manifold Station 14-A-5229) N DSFG5N : Valve Station N 6F DWS : Dukhan Water Sports
FAHM : Manifold Area East Side Pig Receiver Station (16” Loop Line along Gas Operations 6G Dukhan Desalination Plant
P
FAHM : Manifold Area West Side Arab-D injection header – Plot 8) 6P New Data Center and Project Building at QPAA
5 FHGL : Fahahil North Lift Gas Compressor Station 6 Khuff Plants 1 KGPN : Khuff – Point N 6T "IT" Disaster Recovery Building at Dukhan

2 Khatiyah KAHN : Khatiyah North 2 KGPU : Khuff – Point “U” & “U1” 7 All Water Services located outside Oil & Gas Plants
KAHNM1 (KAHN Lift Gas Manifold Station 22-A-4201) 3 KGK1 : Khuff Gas Point K1 7P Water Pumping Station
KAHNM2 (KAHN Lift Gas Manifold Station 22-A-4202) 4 KGK2 : Khuff Gas Point K2 7S New Sewage Water Pumping Station
KAHNM3 (KAHN Lift Gas Manifold Station 22-A-4203) 5 KGK3 : Khuff Gas Point K3 7T Tank Area at Jabel
2 KAHNM4 (KAHN Lift Gas Manifold Station 22-A-4204) 6 KGK4 : Khuff Gas Point K4 All facilities located inside Dukhan Township, including DWCC
8 (Dukhan Water Control Center), except Water & Sewage Services;
KAHNM5 (KAHN Lift Gas Manifold Station 22-A-4205) 7 KGK5 : Khuff Gas Point K5 as follows:
KAHN : Manifold Area West Side 8 KGK6 : Khuff Gas Point K6 8A Al Sidra Mess Hall
KAHN : Manifold Area East Side Offplots/ LBV Station 8B Beach House
KAHN : Additional Oil Inlet Manifolds DOVS1 (Mile 32 Oil Valve Station) UBAB - MES 8C Cinema Dukhan
KAHS : Khatiyah South DOVS2 (KM 6.2 Oil Valve Station) UBAB - MES 8D DOMB (Dukhan Operations Management Building Area)
KAHSM1 (KAHS Lift Gas Manifold Station 23-A-4719) DOVS3 (Mile 42 Oil Valve Station) UBAB - MES 8E DES / DESS (Dukhan English School /Primary and Secondary)
KAHSM2 (KAHS Lift Gas Manifold Station 23-A-4720) DOVS4 (Mile 52 Oil Valve Station) UBAB - MES 8F Fire Station Dukhan Township
3
KAHSM3 (KAHS Lift Gas Manifold Station 23-A-4721) GHIPPS1 (Gas HIPPS Station) NF – Gas Operations (ARAB D) 8G DGC (Dukhan Golf Course)
KAHSM4 (KAHS Lift Gas Manifold Station 23-A-4722) DCVS1 (Mile 26-1 Condensate Valve Station) UBAB - MES 8H Security Gates and Guard House
KAHS : Manifold Area CVFSRG1 (Mile 40 Condensate Valve Station FSP - NGL) 8J JRC (Jinnan Recreation Center)
KAHM : Khatiyah Main CVFSRG2 (Mile 48 Condensate Valve Station FSP - NGL) 8L Al-Lewan Mess Hall
KAHMM1 (KAHM Lift Gas Manifold Station 24-A-5227) DCVS2 (Mile 26-2 Condensate Valve Station) UBAB - MES 8M Medical Center Dukhan
9
KAHMM2 (KAHM Lift Gas Manifold Station 24-A-5228) DCVS3 (Mile 40 Condensate Valve Station) Gas Operations (ARAB 8N New Community Center
4
KAHMM3 (KAHM Lift Gas Manifold Station 24-A-5229) D) - MES 8R DRC (Dukhan Recreation Center)
KAHM : W est Manifold DCVS4 (Mile 48 Condensate Valve Station) Gas Operations (ARAB 8S Township Substations
KAHM : East Manifold D) - MES 8T Township outdoor lighting
4A KMWPSA : Khatiyah Main Potable Water Pump Station A RGLBV1 (Dukhan, LB1 Valve Station On Gas Operations (Arab D- 8U DTS-1 (33kV Substation)

3 Jaleha / Diyab JALM : Jaleha Main NGL4) 8V DTS-2 (33kV Substation)

JALMM1 (JALM Lift Gas Manifold Station 31-A-4919) RGLBV1 (Dukhan, LB2 Valve Station On Gas Operations (Arab D- PFC-DTS1 (88W-BU-0001) : Power Factor Correction
8W
JALMM2 (JALM Lift Gas Manifold Station 31-A-4920) NGL4) (PFC Capacitor Bank) Building at DTS-1

JALMM3 (JALM Lift Gas Manifold Station 31-A-4921) RGLBV3 (Dukhan, LB3 Valve Station On Gas Operations (Arab D- PFC-DTS2 (88X-BU-0001) : Power Factor Correction
8X
JALMM4 (JALM Lift Gas Manifold Station 31-A-4922) NGL4) (PFC Capacitor Bank) Building at DTS-2
1
JALMM5 (JALM Lift Gas Manifold Station 31-A-4923) 9A DRNGL1A : Dukhan Raw NGL - Valve Station 1A All Facilities located within QP Concession areas around Dukhan -
9
JALMM6 (JALM Lift Gas Manifold Station 31-A-4001) 9B DRNGL1B : Dukhan Raw NGL - Valve Station 1B Doha Road after 1st Roundabout except SWTP; as follows:

JALM : East Manifold A KHGA : Khuff Wellhead Treatment Plant A 9A DSSAFS : Fire Station near DSSA
JALM : South Manifold B KHGB : Khuff Wellhead Treatment Plant B 9B Zikreet School for Boys
JALM : North Manifold C KHGC : Khuff Wellhead Treatment Plant C 9C Zikreet School for Girls
DYAB : Diyab D KHGD : Khuff Wellhead Treatment Plant D 9D Hospital Dukhan (Cuban Hospital)
DYAB : Oil Inlet Manifold Skid No. 1 DD Pig Launcher Station (16” Header Pipeline near KHGD, Plot 1) 9E DSSA : Dukhan Support Facilities Area
2
DYAB : Oil Inlet Manifold Skid No. 2 E KHGE : Khuff Wellhead Treatment Plant E 9F New DSSA Area
DYAB : Oil Inlet Manifold Skid No. 3 G KHGG : Khuff Wellhead Treatment Plant G PFC-ZK (89G-BU-0001) : Power Factor Correction
9G
3 UBAB : Umm Bab Pumping Station H KHGH : Khuff Wellhead Treatment Plant H (PFC Capacitor Bank) Building at Zekreet Substation

3A UBWPSA : Umm Bab Potable Water Pump Station A L KHGL : Khuff Wellhead Treatment Plant L 9Z ZKSS : Zikreet Substation
4 Umm Bab S.S. LL MANHL : New Manifold area between KHGH & KHGL CONTINUED ABOVE-RIGHT

PFC-UB (34A-BU-0001) : Power Factor Correction (PFC Capacitor 7 North Field T ie-Ins PR1FNF: New Pig Receiver for NF Injection Header
4A 1
Bank) Building at Umm Bab Substation (inside fence of HIPPS Area)

5 UBSEC (Ummbab Security Bldg) 4 Inlet Manifold / Offplots (Previously Procedure 234)

4 PWI 0 Ring Main FAHN : Fahahil North Field - Fahahil Compression

9
1 PW01 : Power Water Injection – PS 1 (Previously Procedure 234)

2 PW02 : Power Water Injection – PS 2 PL1FNF : New Pig Launcher Station for NF Injection Header
A
3 PW03 : Power Water Injection – PS 3 (Outside, fence of NFIS Station)

4 PW04 : Power Water Injection – PS 4 8 Dukhan Facilities 2 Workshops

5 PW05 : Power Water Injection – PS 5 4 SWTP : Sewage Treatment Plant
6 PW06 : Power Water Injection – PS 6 4A SWTP : New Sewage Treatment Plant
7 PW07 : Power Water Injection – PS 7
All facilities within QP concession areas located outside township
8 PW08 : Power Water Injection – PS 8 5 and outside Zikreet and West of Dukhan - Ummbab Road and up to
1st Roundabout of Dukhan - Doha Road; as follows:
9 PW09 : Power Water Injection – PS 9
A PWC1 : Power Water Injection – Cluster 1 5A Dukhan Commercial Area
B PWC2 : Power Water Injection – Cluster 2 5B Dukhan Mosque
C PWC3 : Power Water Injection – Cluster 3 5C Dukhan Police Station
CONTINUED ABOVE-RIGHT CONTINUED ABOVE-RIGHT

Doc. No.: QP-ENG-LST-013-001 Rev. 00 Date: 01/07/2019 Page 55 of 86

 QP STANDARD FOR EQUIPMENT IDENTIFICATION AND TAG NUMBERING SYSTEM – DUKHAN FIELDS

DOC. No. QP-ENG-STD-013 Rev. 00

APPENDIX B: INSTRUMENT FUNCTION CODES

FUNCTION LETTER CODES DUKHAN FIELDS TYPICAL LETTER COMBINATIONS
FIRST-LETTER SUCCEEDING-LETTER(S)
DESCRIPTION CODE DESCRIPTION CODE DESCRIPTION CODE DESCRIPTION CODE
MEASURED OR READOUT OR
VARIABLE OUTPUT/ACTIVE FUNCTION
INITIATING PASSIVE
MODIFIER FUNCTION MODIFIER Analyser Flow (Continuation) Pressure (Continuation) Temperature (Continuation)
VARIABLE FUNCTION
Analyser Alarm AA Flow Switch Low-Low FSLL Pressure Alarm Low PAL Thermowell TW
A Analysis - Alarm - -
Analyser Alarm High AAH Flow Transmitter FT Pressure Alarm Low-Low PALL Vibration

Burner, Analyser Alarm High-High AAHH Hand Pressure Control Valve PCV Vibration Element VE
B - Status Display User's Choice User's Choice
Combustion Analyser Alarm Low AAL Hand Control Valve HCV Pressure Controller PC Vibration Transmitter VT

Conductivity Analyser Alarm Low-Low AALL Hand Indicating Controller HIC Pressure Converter PY Vibration Switch VS
C - - Control Close
(Electrical) Analyser Element AE Pressure Differential Alarm High PDAH Miscellaneous
Hand Switch
HS
Analyser Indicator AI (covered by Electrical Table 5 ) Pressure Differential Alarm Low PDAL Alarm Miscellaneous XA
Density or Specific
D Differential - - Deviation
Gravity Analyser Indicator Transmitter AIT Hand Solenoid Valve - No such Item Conductivity Cell CE
Pressure Differential Indicating
please check This would be HS or HZ PDIC
Analyser Recorder Controller ARC HSV Controller Loop Isolator LIS
Sensor, (Primary which would initiate the solenoid Valve
E Voltage (EMF) - - -
Element) Cell Analyser Switch AS for local valve shutdown Maintenance Override Switch MOS
Pressure Differential Indicating
PDIT
Analyser Switch High ASH Level Transmitter Miscellaneous Indicator XI
F Flow, Flow Rate Ratio (Fraction) - - -
Analyser Switch Low ASL Level Alarm High LAH Pressure Differential Indicator PDI Quantity Transmitter (Totalise) QT
Glass, Gauge, Analyser Transmitter AT Level Alarm High-High LAHH Pressure Differential Switch High PDSH Restriction Orifice RO
G Position, Running - - -
Viewing Device Density Level Alarm Low LAL Pressure Differential Switch Low PDSL Single Loop Programmable Controller SLPC

Hand (manually Density Element DE Level Alarm Low-Low LALL Pressure Differential Transmitter PDT Solenoid Valve General (Not installed in
H - - - High SOV
initiated) Density Indicator DI Level Control LC Pressure Indicating Transmitter PIT Instrument Loop)

Density Indicator Controller DIC Level Control Valve LCV Pressure Indicator (Pressure Gauge) PI Solenoid Valve installed on Blow Down
I Current (Electrical) - Indicate - - BSV
Density Transmitter DT Level Converter/Transducer LY Pressure Recorder PR Valve

Flow Level Element LE Pressure Recorder Controller PRC Solenoid Valve Shutdown SSV
J Power - Scan - -
Flow Alarm High FAH Level Gauge LG Pressure Solenoid Valve PSV Torque Switch high TQH

Time rate of Flow Alarm High-High FAHH Level Indicating Transmitter LIT Pressure Switch PS Torque Switch high alarm TQAH
K Time, Schedule - Control Station -
change Flow Alarm Low FAL Level Indicator LI Pressure Switch High PSH Vacuum Leak Detector VLD
Flow Alarm Low-Low FALL Level Indicator Controller LIC Pressure Switch High-High PSHH
L Level - Light, Lamp - Low
Flow Control FC Level Recorder LR Pressure Switch Low PSL

Middle, Flow Control Valve FCV Level Recording Controller LRC Pressure Switch Low-Low PSLL
M Moisture Momentary - -
Intermediate Flow Differential Alarm High FDAH Level Solenoid Valve LSV Pressure Transmitter PT
Flow Differential Alarm High-High FDAHH Level Switch LS Speed
N User's Choice - User's Choice User's Choice User's Choice
Flow Differential Alarm Low FDAL Level Switch High LSH Speed Alarm Switch Low SASL
Flow Differential Switch Low FDSL Level Switch High-High LSHH Speed Controller SC
O User's Choice - Orifice (RO) - Open
Flow Element FE Level Switch Low LSL Speed Indicator SI

Point (Test), Flow Indicating Transmitter FIT Level Switch Low-Low LSLL Speed Indicator Controller SIC
P Pressure, Vacuum - - -
Connection Flow Indicator FI Level Transmitter LT Speed Sensing Element SSE
Flow Indicator Controller FIC Moisture Speed Switch SSW
Q Quantity Integrate, Totalise Integrate, Totalise - -
Flow Integrate Controller FQC Moisture Cell ME Temperature

Recorder, Flow Integrate Indicator or Flow Meter Moisture Indicator MI Temperature Alarm High TAH
R Radiation - - Run FQI
Recording (Multiphase) Moisture Indicator Transmitter MIT Temperature Alarm High-High TAHH

Switch (sequence Flow Integrate Recorder FQR Position Temperature Alarm Low TAL
S Speed, Frequency - - Stop
control) Flow Orifice FO Position Alarm ZA Temperature Alarm Low-Low TALL
Flow Position Alarm Close FZAC Position Element ZE Temperature Controller TC
T Temperature - - Transmitting -
Flow Position Alarm Open FZAO Position Indicating Controller ZIC Temperature Control Valve TCV
Flow Position Indicator FZI Position Indicator ZI Temperature Element TE
U Function Blocks - Multifunction Multifunction Multifunction
Flow Position Transmitter FZT Position Limit Switch Close ZSC Temperature Indicator TI
Vibration, Flow Recorder FR Temperature Indicating Controller TIC
Valve, Damper, Position Limit Switch Close
V Mechanical - - - ZLC
Louver Flow Recording Controller FRC Lamp/Indicator Temperature Indicating Transmitter TIT
Analysis
Flow Relay/ Computer/ Converter FY Position Limit Switch Open ZSO Temperature Recorder TR
W Weight, Force - Well - -
Flow Sight Glass Position Limit Switch Open Temperature Switch TS
FG ZLO
(covered by Mechanical Table 2) Lamp/Indicator Temperature Switch High TSH
Unclassified, Unclassified,
X X-Axis Unclassified Unclassified
Miscellaneous Accessory Devices Flow Solenoid Valve FSV Position Switch ZS Temperature Switch High-High TSHH
Relay, Computer, Flow Switch FS Position Transmitter ZT Temperature Switch Low TSL
Event. State,
Y Y-Axis - Converter, -
Presence Flow Switch High FSH Pressure Temperature Switch Low-Low TSLL
Transducer
Driver, Actuator, Flow Switch High-High FSHH Pressure Alarm High PAH Temperature Transducer TY
Position, Emergency, Safety
Z Z-Axis Final Control -
Dimension Action Flow Switch Low FSL Pressure Alarm High-High PAHH Temperature Transmitter TT
Element,
Continued Above-Right Continued Above-Right Continued Above-Right

Doc. No.: QP-ENG-LST-013-002 Rev.00 Date: 01/07/2019 Page 56 of 86

 QP STANDARD FOR EQUIPMENT IDENTIFICATION AND TAG
NUMBERING SYSTEM – DUKHAN FIELDS

DOC. No. QP-ENG-STD-013 Rev. 00

APPENDIX C: TAG REQUEST/ADVICE FORM

Sample Only

Doc. No.: QP-ENG-STD-013 Rev. 00 Date: 01/07/2019 Page 57 of 86

 QP STANDARD FOR EQUIPMENT IDENTIFICATION AND TAG
NUMBERING SYSTEM – DUKHAN FIELDS

DOC. No. QP-ENG-STD-013 Rev. 00

APPENDIX C: TAG REQUEST/ADVICE FORM (Contd.)

Sample Only

Doc. No.: QP-ENG-STD-013 Rev. 00 Date: 01/07/2019 Page 58 of 86

 QP STANDARD FOR EQUIPMENT IDENTIFICATION AND TAG
NUMBERING SYSTEM – DUKHAN FIELDS
DOC. No. QP-ENG-STD-013 Rev. 00

APPENDIX D: REQUEST FOR VARIANCE TO STANDARD

Sample Only

Doc. No.: QP-ENG-STD-013 Rev. 00 Date: 01/07/2019 Page 59 of 86

 QP STANDARD FOR EQUIPMENT IDENTIFICATION AND TAG
NUMBERING SYSTEM – DUKHAN FIELDS
DOC. No. QP-ENG-STD-013 Rev. 00

APPENDIX E1: PWI WELLS – TYPE 1 PRESSURE BLEED LINE WITH GLV VALVES

MECHANICAL TYPICAL TAGS FOR PWI WELLS

SI. WELL
TAG NUMBER SIZE VALVE TYPE LOCATION REMARKS
NO. NO.
EXISTING 6"/8” RING
1 DK-NNN DKNNN-BV-101A 4" BALL VALVE
MAIN HEADER
MAIN INJECTION LINE
2 DK-NNN DKNNN-BV-102 4" BALL VALVE
WELLHEAD FENCE
3 DK-NNN DKNNN-BV-103 4" BALL VALVE DRAIN LINE

4 DK-NNN DKNNN-BV-104 3/4" BALL VALVE SRV-101 ISOLATION

5 DK-NNN DKNNN-BV-105 2" BALL VALVE PI-103 ISOLATION

6 DK-NNN DKNNN-BV-106 2" BALL VALVE PI-102 ISOLATION

7 DK-NNN DKNNN-BV-107 2" BALL VALVE PIT-101 ISOLATION

8 DK-NNN DKNNN-BV-109 1" BALL VALVE SAMPLE POINT

9 DK-NNN DKNNN-BV-116 1" BALL VALVE PI-104 ISOLATION

10 DK-NNN DKNNN-BV-118 1” BALL VALVE PIT-104 ISOLATION

GLOBE
11 DK-NNN DKNNN-GLV-120 2" BLEED LINE
VALVE
12 DK-NNN DKNNN-BV-121 1" BALL VALVE PI-105 ISOLATION

13 DK-NNN DKNNN-BV-123 1” BALL VALVE PIT-105 ISOLATION

14 DK-NNN DKNNN-BV-126 1" BALL VALVE PI-106 ISOLATION

DOUBLE
BLOCK &
15 DK-NNN DKNNN-DBV-127 1" PI-106 ISOLATION
BLEED
VALVE
16 DK-NNN DKNNN-BV-128 1” BALL VALVE PIT-106 ISOLATION
GLOBE
17 DK-NNN DKNNN-GLV-130 2" BLEED LINE
VALVE
18 DK-NNN DKNNN-BV-136 1" BALL VALVE BLEED LINE
GLOBE
19 DK-NNN DKNNN-GLV-137 2" BLEED LINE
VALVE
GLOBE
20 DK-NNN DKNNN-GLV- 138 2" BLEED LINE
VALVE
GLOBE
21 DK-NNN DKNNN-GLV-139 2" BLEED LINE
VALVE
22 DK-NNN DKNNN-BV-140 2" BALL VALVE PIT-103 ISOLATION

23 DK-NNN DKNNN-BV-142 4" BALL VALVE DRAIN LINE

Doc. No.: QP-ENG-LST-013-003 Rev. 00 Date: 01/07/2019 Page 60 of 86

 QP STANDARD FOR EQUIPMENT IDENTIFICATION AND TAG
NUMBERING SYSTEM – DUKHAN FIELDS
DOC. No. QP-ENG-STD-013 Rev. 00

APPENDIX E1: PWI WELLS – TYPE 1 PRESSURE BLEED LINE WITH GLV VALVES
(Contd.)
MECHANICAL TYPICAL TAGS FOR PWI WELLS (Continuation)
SI. WELL
TAG NUMBER SIZE VALVE TYPE LOCATION REMARKS
NO. NO.
DOUBLE
24 DK-NNN DKNNN-DBV-111 2" BLOCK & PI-103 ISOLATION
BLEED VALVE
DOUBLE
25 DK-NNN DKNNN-DBV-112 2" BLOCK & PI-102 ISOLATION
BLEED VALVE
DOUBLE
26 DK-NNN DKNNN-DBV-113 2" BLOCK & PIT-101 ISOLATION
BLEED VALVE
DOUBLE
27 DK-NNN DKNNN-DBV-117 1" BLOCK & PI-104 ISOLATION
BLEED VALVE
DOUBLE
28 DK-NNN DKNNN-DBV-119 1” BLOCK & PIT-104 ISOLATION
BLEED VALVE
DOUBLE
29 DK-NNN DKNNN-DBV-122 1" BLOCK & PT-105 ISOLATION
BLEED VALVE
DOUBLE
30 DK-NNN DKNNN-DBV-124 1” BLOCK & PIT-105 ISOLATION
BLEED VALVE
DOUBLE
31 DK-NNN DKNNN-DBV-129 1” BLOCK & PIT-106 ISOLATION
BLEED VALVE
DOUBLE
32 DK-NNN DKNNN-DBV-141 2" BLOCK & PIT-103 ISOLATION
BLEED VALVE
CORROSION MAIN INJECTION
33 DK-NNN DKNNN-CC-102 -
COUPON LINE
SAFETY MAIN INJECTION
34 DK-NNN DKNNN-SRV-101 3/4"
RELEIF VALVE LINE
MAIN INJECTION
35 DK-NNN DKNNN-CHV-101 4" CHOKE VALVE
LINE
4 NON-RETURN MAIN INJECTION
36 DK-NNN DKNNN-NRV-101
1/16" VALVE LINE
SCALE MAIN INJECTION
37 DK-NNN DKNNN-CC-101 -
COUPON LINE

Doc. No.: QP-ENG-LST-013-003 Rev. 00 Date: 01/07/2019 Page 61 of 86

 QP STANDARD FOR EQUIPMENT IDENTIFICATION AND TAG
NUMBERING SYSTEM – DUKHAN FIELDS
DOC. No. QP-ENG-STD-013 Rev. 00

APPENDIX E1: PWI WELLS – TYPE 1 PRESSURE BLEED LINE WITH GLV VALVES
(Contd.)
INSTRUMENTATION TYPICAL TAGS FOR PWI WELLS
SI. WELL
TAG NUMBER SIZE VALVE TYPE LOCATION REMARKS
NO. NO.
38 DK-NNN DKNNN-GLV-125 2” GLOBE VALE BLEED LINE
PRESSURE ABOVE X-MAS
39 DKNNN DKNNN-PI-101 -
INDICATOR TREE
PRESSURE
40 DKNNN DKNNN-PI-102 - PI IN MAIN LINE
INDICATOR
PRESSURE
41 DKNNN DKNNN-PI-103 - PI IN MAIN LINE
INDICATOR
PRESSURE
42 DKNNN DKNNN-PI-104 - BLEED LINE
INDICATOR
PRESSURE
43 DKNNN DKNNN-PI-105 - BLEED LINE
INDICATOR
PRESSURE
44 DKNNN DKNNN-PI-106 - BLEED LINE
INDICATOR
PRESSURE
45 DKNNN DKNNN-PIT-101 - INDICATING PIT MAIN LINE
TRANSMITTER
PRESSURE
46 DKNNN DKNNN-PIT-103 - INDICATING PIT MAIN LINE
TRANSMITTER
PRESSURE
47 DKNNN DKNNN-PIT-104 - INDICATING PIT BLEED LINE
TRANSMITTER
PRESSURE
48 DKNNN DKNNN-PIT-105 - INDICATING PIT BLEED LINE
TRANSMITTER
PRESSURE
49 DKNNN DKNNN-PIT-106 - INDICATING PIT BLEED LINE
TRANSMITTER
RESTRICTION
50 DKNNN DKNNN-RO-101 - BLEED LINE
ORIFICE
RESTRICTION
51 DKNNN DKNNN-RO-102 - BLEED LINE
ORIFICE
RESTRICTION
52 DKNNN DKNNN-RO-103 - BLEED LINE
ORIFICE
FLOW
53 DKNNN DKNNN-FQI-101 - MAIN LINE
ANALYSIZER
FLOW
54 DKNNN DKNNN-FIT-101 - INDICATING MAIN LINE
TRANSMITTER

Doc. No.: QP-ENG-LST-013-003 Rev. 00 Date: 01/07/2019 Page 62 of 86

 QP STANDARD FOR EQUIPMENT IDENTIFICATION AND TAG
NUMBERING SYSTEM – DUKHAN FIELDS
DOC. No. QP-ENG-STD-013 Rev. 00

APPENDIX E2: PWI WELLS – TYPE 2 PRESSURE BLEED LINE WITH BV VALVES

MECHANICAL TYPICAL TAGS FOR PWI WELLS

SI. WELL
TAG NUMBER SIZE VALVE TYPE LOCATION REMARKS
NO. NO.
EXISTING 6"/8” RING
1 DK-NNN DKNNN-BV-101A 4" BALL VALVE
MAIN HEADER
MAIN INJECTION LINE
2 DK-NNN DKNNN-BV-102 4" BALL VALVE
WELLHEAD FENCE
3 DK-NNN DKNNN-BV-103 4" BALL VALVE DRAIN LINE

4 DK-NNN DKNNN-BV-104 3/4" BALL VALVE SRV-101 ISOLATION

5 DK-NNN DKNNN-BV-105 2" BALL VALVE PI-103 ISOLATION

6 DK-NNN DKNNN-BV-106 2" BALL VALVE PI-102 ISOLATION

7 DK-NNN DKNNN-BV-107 2" BALL VALVE PIT-101 ISOLATION

8 DK-NNN DKNNN-BV-109 1" BALL VALVE SAMPLE POINT

9 DK-NNN DKNNN-BV-116 1" BALL VALVE PI-104 ISOLATION

10 DK-NNN DKNNN-BV-118 1” BALL VALVE PIT-104 ISOLATION

11 DK-NNN DKNNN-BV-120 2" BALL VALVE BLEED LINE

12 DK-NNN DKNNN-BV-121 1" BALL VALVE PI-105 ISOLATION

13 DK-NNN DKNNN-BV-123 1” BALL VALVE PIT-105 ISOLATION

14 DK-NNN DKNNN-BV-126 1" BALL VALVE PI-106 ISOLATION

DOUBLE
15 DK-NNN DKNNN-DBV-127 1" BLOCK & PI-106 ISOLATION
BLEED VALVE
16 DK-NNN DKNNN-BV-128 1/2" BALL VALVE PIT-106 ISOLATION

17 DK-NNN DKNNN-BV-130 2" BALL VALVE BLEED LINE

18 DK-NNN DKNNN-BV-136 1" BALL VALVE BLEED LINE

19 DK-NNN DKNNN-BV-137 2" BALL VALVE BLEED LINE

20 DK-NNN DKNNN-BV- 138 2" BALL VALVE BLEED LINE

21 DK-NNN DKNNN-BV-139 2" BALL VALVE BLEED LINE

22 DK-NNN DKNNN-BV-140 2" BALL VALVE PIT-103 ISOLATION

23 DK-NNN DKNNN-BV-142 4" BALL VALVE DRAIN LINE

DOUBLE
24 DK-NNN DKNNN-DBV-111 2" BLOCK & PI-103 ISOLATION
BLEED VALVE
DOUBLE
25 DK-NNN DKNNN-DBV-112 2" BLOCK & PI-102 ISOLATION
BLEED VALVE

Doc. No.: QP-ENG-LST-013-004 Rev. 00 Date: 01/07/2019 Page 63 of 86

 QP STANDARD FOR EQUIPMENT IDENTIFICATION AND TAG
NUMBERING SYSTEM – DUKHAN FIELDS
DOC. No. QP-ENG-STD-013 Rev. 00

APPENDIX E2: PWI WELLS – TYPE 2 PRESSURE BLEED LINE WITH BV VALVES (Contd.)

MECHANICAL TYPICAL TAGS FOR PWI WELLS (Continuation)

SI. WELL
TAG NUMBER SIZE VALVE TYPE LOCATION REMARKS
NO. NO.
DOUBLE BLOCK &
26 DK-NNN DKNNN-DBV-113 2" PIT-101 ISOLATION
BLEED VALVE
DOUBLE BLOCK &
27 DK-NNN DKNNN-DBV-117 1" PI-104 ISOLATION
BLEED VALVE
DOUBLE BLOCK &
28 DK-NNN DKNNN-DBV-119 1” PIT-104 ISOLATION
BLEED VALVE
DOUBLE BLOCK &
29 DK-NNN DKNNN-DBV-122 1" PT-105 ISOLATION
BLEED VALVE
DOUBLE BLOCK &
30 DK-NNN DKNNN-DBV-124 1” PIT-105 ISOLATION
BLEED VALVE
DOUBLE BLOCK &
31 DK-NNN DKNNN-DBV-129 1” PIT-106 ISOLATION
BLEED VALVE
DOUBLE BLOCK &
32 DK-NNN DKNNN-DBV-141 2" PIT-103 ISOLATION
BLEED VALVE
CORROSION
33 DK-NNN DKNNN-CC-102 - MAIN INJECTION LINE
COUPON
SAFETY RELEIF
34 DK-NNN DKNNN-SRV-101 3/4" MAIN INJECTION LINE
VALVE
35 DK-NNN DKNNN-CHV-101 4" CHOKE VALVE MAIN INJECTION LINE
4 NON-RETURN
36 DK-NNN DKNNN-NRV-101 MAIN INJECTION LINE
1/16" VALVE
37 DK-NNN DKNNN-CC-102 - SCALE COUPON MAIN INJECTION LINE

INSTRUMENTATION TYPICAL TAGS FOR PWI WELLS

SI. WELL
TAG NUMBER SIZE VALVE TYPE LOCATION REMARKS
NO. NO.
PRESSURE
38 DKNNN DKNNN-PI-101 - ABOVE X-MAS TREE
INDICATOR
PRESSURE
39 DKNNN DKNNN-PI-102 - PI IN MAIN LINE
INDICATOR
PRESSURE
40 DKNNN DKNNN-PI-103 - PI IN MAIN LINE
INDICATOR
PRESSURE
41 DKNNN DKNNN-PI-104 - BLEED LINE
INDICATOR
PRESSURE
42 DKNNN DKNNN-PI-105 - BLEED LINE
INDICATOR
PRESSURE
43 DKNNN DKNNN-PI-106 - BLEED LINE
INDICATOR
PRESSURE
44 DKNNN DKNNN-PIT-101 - INDICATING PIT MAIN LINE
TRANSMITTER

Doc. No.: QP-ENG-LST-013-004 Rev. 00 Date: 01/07/2019 Page 64 of 86

 QP STANDARD FOR EQUIPMENT IDENTIFICATION AND TAG
NUMBERING SYSTEM – DUKHAN FIELDS
DOC. No. QP-ENG-STD-013 Rev. 00

APPENDIX E2: PWI WELLS – TYPE 2 PRESSURE BLEED LINE WITH BV VALVES
(Contd.)

INSTRUMENTATION TYPICAL TAGS FOR PWI WELLS (Continuation)

SI. WELL
TAG NUMBER SIZE VALVE TYPE LOCATION REMARKS
NO. NO.
PRESSURE INDICATING PIT MAIN
45 DKNNN DKNNN-PIT-103 -
TRANSMITTER LINE
PRESSURE INDICATING PIT BLEED
46 DKNNN DKNNN-PIT-104 -
TRANSMITTER LINE
PRESSURE INDICATING PIT BLEED
47 DKNNN DKNNN-PIT-105 -
TRANSMITTER LINE
PRESSURE INDICATING PIT BLEED
48 DKNNN DKNNN-PIT-106 -
TRANSMITTER LINE
49 DKNNN DKNNN-RO-101 - RESTRICTION ORIFICE BLEED LINE

50 DKNNN DKNNN-RO-102 - RESTRICTION ORIFICE BLEED LINE

51 DKNNN DKNNN-RO-103 - RESTRICTION ORIFICE BLEED LINE

52 DKNNN DKNNN-FQI-101 - FLOW ANALYSIZER MAIN LINE

FLOW INDICATING
53 DKNNN DKNNN-FIT-101 - MAIN LINE
TRANSMITTER

Doc. No.: QP-ENG-LST-013-004 Rev. 00 Date: 01/07/2019 Page 65 of 86

 QP STANDARD FOR EQUIPMENT IDENTIFICATION AND TAG
NUMBERING SYSTEM – DUKHAN FIELDS
DOC. No. QP-ENG-STD-013 Rev. 00

APPENDIX F: STANDARD EQUIPMENT TAGS – GAS LIFT WELLS

GAS LIFT WELLS TYPICAL TAGS
SI.
TAG NUMBER VALVE TYPE LOCATION
NO.
1 DKNNN-BV-201 BALL VALVE GASLIFT MAIN LINE
GASLIFT BRANCH CONNECTION TO
2 DKNNN-BV-202 BALL VALVE
OPERATE SDV
GASLIFT BRANCH CONNECTION TO
3 DKNNN-BV-206 BALL VALVE
OPERATE SDV
DOUBLE BLOCK & GASLIFT BRANCH CONNECTION TO
5 DKNNN-DBV-207
BLEED VALVE PRESSURE GAUAGE
DOUBLE BLOCK &
6 DKNNN-DBV-203 SDV/WHCP PANEL CONNECTION
BLEED VALVE
7 DKNNN-NRV-205 CHECK VALVE GASLIFT MAIN LINE
PRESSURE
8 DKNNN-PI-201 GASLIFT MAIN LINE
INDICATOR
9 DKNNN-SDV-201 SHUTDOWN VALVE GASLIFT MAIN LINE
10 DKNNN-CC-201 CORROSION COUPON GASLIFT MAIN LINE

Doc. No.: QP-ENG-LST-013-005 Rev. 00 Date: 01/07/2019 Page 66 of 86

 QP STANDARD FOR EQUIPMENT IDENTIFICATION AND TAG NUMBERING SYSTEM – DUKHAN FIELDS

DOC. No. QP-ENG-STD-013 Rev. 00

APPENDIX G: STANDARD EQUIPMENT TAGS – WATER SOURCE WELLS

WATER SOURCE WELLS TYPICAL TAGS
SI. SI. SI.
TAG NUMBER SIZE Description LOCATION TAG NUMBER SIZE Description LOCATION TAG NUMBER SIZE Description LOCATION
NO. NO. NO.
SOURCE WATER MAIN
1 DKWNNN-BV-401 1" BALL VALVE VENT LINE 26 DKWNNN-BV-426 2" BALL VALVE 51 DKWNNN-BV-437 1" BALL VALVE NITROGEN LINE
LINE
SOURCE WATER
2 DKWNNN-BV-402 8" BALL VALVE 27 DKWNNN-BV-427 2" BALL VALVE RETURN LINE 52 DKWNNN-BV-438 1" BALL VALVE NITROGEN LINE
MAIN LINE
SOURCE WATER SOURCE WATER MAIN
3 DKWNNN-BV-403 8" BALL VALVE 28 DKWNNN-BV-428 1" BALL VALVE 53 DKWNNN-GLV-447 1" GLOBE VALVE NITROGEN LINE
MAIN LINE LINE
SOURCE WATER SOURCE WATER MAIN
4 DKWNNN-BV-405 8" BALL VALVE 29 DKWNNN-BV-429 1" BALL VALVE 54 DKWNNN-GLV- 448 1" GLOBE VALVE NITROGEN LINE
MAIN LINE LINE
SOURCE WATER SOURCE WATER MAIN NON-RETURN
5 DKWNNN-BV-404 8" BALL VALVE 30 DKWNNN-BV-431 3/4" BALL VALVE 55 DKWNNN-NRV-441 1" NITROGEN LINE
MAIN LINE LINE VALVE
SOURCE WATER MAIN NON-RETURN
6 DKWNNN-BV-406 1.1/2" BALL VALVE RETURN LINE 31 DKWNNN-BV-439 1" BALL VALVE 56 DKWNNN-NRV-442 1" NITROGEN LINE
LINE VALVE
SAFETY RELEIF SOURCE WATER MAIN
7 DKWNNN-BV-407 1.1/2" BALL VALVE RETURN LINE 32 DKWNNN-SRV-453 3/4" 57 DKWNNN-NLV-451 3/8" NEEDLE VALVE NITROGEN LINE
VALVE LINE
SAFETY RELEIF SOURCE WATER MAIN
8 DKWNNN-BV-408 1.1/2" BALL VALVE DRAIN LINE 33 DKWNNN-SRV-454 3/4" 58 DKWNNN-NLV-452 3/8" NEEDLE VALVE NITROGEN LINE
VALVE LINE
SAFETY RELEIF SOURCE WATER MAIN SAFETY RELEIF
9 DKWNNN-BV-409 1" BALL VALVE DRAIN LINE 34 DKWNNN-SRV-455 3/4" 59 DKWNNN-SRV-457 3/4" NITROGEN LINE
VALVE LINE VALVE
CHEMICAL SAFETY RELEIF SOURCE WATER MAIN SAFETY RELEIF
10 DKWNNN-BV-410 1" BALL VALVE 35 DKWNNN-SRV-456 3/4" 60 DKWNNN-SRV-458 3/4" NITROGEN LINE
INJECTION VALVE LINE VALVE
SOURCE WATER SOURCE WATER MAIN PRESSURE
11 DKWNNN-BV-411 1" BALL VALVE 36 DKWNNN-GLV-443 1" GLOBE VALVE 61 DKWNNN-PI-459 - SOURCE WATER MAIN LINE
MAIN LINE LINE INDICATOR
SOURCE WATER PRESSURE
12 DKWNNN-BV-412 3/4" BALL VALVE 37 DKWNNN-GLV-444 2" GLOBE VALVE DRAIN LINE 62 DKWNNN-PI-460 - SOURCE WATER MAIN LINE
MAIN LINE INDICATOR
SOURCE WATER SOURCE WATER MAIN PRESSURE
13 DKWNNN-BV-413 3/4" BALL VALVE 38 DKWNNN-GLV-445 1" GLOBE VALVE 63 DKWNNN-PI-461 - SOURCE WATER MAIN LINE
MAIN LINE LINE INDICATOR
SOURCE WATER PRESSURE
14 DKWNNN-BV-414 1" BALL VALVE 39 DKWNNN-GLV-446 2" GLOBE VALVE DRAIN LINE 64 DKWNNN-PI-462 - DRAIN LINE
MAIN LINE INDICATOR
SOURCE WATER SOURCE WATER MAIN PRESSURE
15 DKWNNN-BV-415 1" BALL VALVE 40 DKWNNN-NLV-449 1" NEEDLE VALVE 65 DKWNNN-PI-463 - NITORGEN LINE
MAIN LINE LINE INDICATOR
SOURCE WATER SOURCE WATER MAIN PRESSURE
16 DKWNNN-BV-416 1" BALL VALVE 41 DKWNNN-NLV-450 1" NEEDLE VALVE 66 DKWNNN-PI-464 - NITORGEN LINE
MAIN LINE LINE INDICATOR
SOURCE WATER NON-RETURN PRESSURE
17 DKWNNN-BV-417 1" BALL VALVE 42 DKWNNN-NRV-440 2" RETURN LINE 67 DKWNNN-PI-465 - NITORGEN LINE
MAIN LINE VALVE INDICATOR
PRESSURE
SOURCE WATER NON-RETURN
18 DKWNNN-BV-418 1" BALL VALVE 43 DKWNNN-NRV-439 1" CHEMICAL INJECTION 68 DKWNNN-PDT-469 - DIFFERENTIAL SOURCE WATER MAIN LINE
MAIN LINE VALVE
TRANSMITTER
PRESSURE
SOURCE WATER SOURCE WATER MAIN
19 DKWNNN-BV-419 1" BALL VALVE 44 DKWNNN-S-480 - FILTER 69 DKWNNN-PDT-470 - DIFFERENTIAL SOURCE WATER MAIN LINE
MAIN LINE LINE
TRANSMITTER
SOURCE WATER SOURCE WATER MAIN LEVEL
20 DKWNNN-BV-420 3/4" BALL VALVE 45 DKWNNN-S-481 - FILTER 70 DKWNNN-LT-466 - NITOGEN LINE
MAIN LINE LINE TRANSMITTER
SOURCE WATER RESTRICTION
21 DKWNNN-BV-421 1" BALL VALVE 46 DKWNNN-BV-432 1" BALL VALVE NITROGEN LINE 71 DKWNNN-RO-471 - SOURCE WATER MAIN LINE
MAIN LINE ORIFICE
SOURCE WATER
22 DKWNNN-BV-422 1" BALL VALVE 47 DKWNNN-BV-433 1" BALL VALVE NITROGEN LINE 72 DKWNNN-FI-468 - FLOW INDICATOR NITROGEN LINE
MAIN LINE
SOURCE WATER
23 DKWNNN-BV-423 1" BALL VALVE 48 DKWNNN-BV-434 1" BALL VALVE NITROGEN LINE 73 DKWNNN-FY-467 - FLOW RELAY NITROGEN LINE
MAIN LINE
SOURCE WATER
24 DKWNNN-BV-424 1" BALL VALVE 49 DKWNNN-BV-435 1" BALL VALVE NITROGEN LINE
MAIN LINE
SOURCE WATER
25 DKWNNN-BV-425 2" BALL VALVE 50 DKWNNN-BV-436 1" BALL VALVE NITROGEN LINE
MAIN LINE

Doc. No.: QP-ENG-LST-013-006 Rev. 00 Date: 01/07/2019 Page 67 of 86

 QP STANDARD FOR EQUIPMENT IDENTIFICATION AND TAG
NUMBERING SYSTEM – DUKHAN FIELDS
DOC. No. QP-ENG-STD-013 Rev. 00

APPENDIX H: STANDARD EQUIPMENT TAGS – RE-CIRCULATION WELLS

RE-CIRCULATION WELLS TYPICAL TAGS
SI.
TAG NUMBER - QP SIZE VALVE TYPE LOCATION REMARKS
NO.
MAIN LINE NEAR
1 DKWRNNN-GV-501 8" GATE VALVE
WELLHEAD FENCE
DOUBLE BLOCK &
2 DKWRNNN-DBV-502 2" PI-501 ISOLATION
BLEED VALVE
MAIN LINE NEAR 8”
3 DKWRNNN-PI-501 ½” PRESSURE GAUGE
GATE VALVE

Doc. No.: QP-ENG-LST-013-007 Rev. 00 Date: 01/07/2019 Page 68 of 86

 QP STANDARD FOR EQUIPMENT IDENTIFICATION AND TAG
NUMBERING SYSTEM – DUKHAN FIELDS
DOC. No. QP-ENG-STD-013 Rev. 00

APPENDIX I1: OIL WELLS – TYPE 1 WITH HYDRAULIC WELLHEAD CONTROL

PANEL, PRESSURE BLEED LINE WITH GLV VALVES
MECHANICAL TYPICAL TAGS FOR OIL WELLS
SI. WELL
TAG NUMBER SIZE VALVE TYPE LOCATION REMARKS
NO. NO.
MAIN PRODUCTION LINE
1 DK-NNN DKNNN-BV-110 6" BALL VALVE
NEAR WELLHEAD FENCE
MAIN PRODUCTION LINE
2 DK-NNN DKNNN-BV-111 6" BALL VALVE
NEAR WELLHEAD FENCE
3 DK-NNN DKNNN-BV-112 1" BALL VALVE PRODUCTION DRAIN
4 DK-NNN DKNNN-BV-113 4" BALL VALVE POTABLE CONNECTION
POTABLE CONNECTION-
5 DK-NNN DKNNN-BV-114 1" BALL VALVE
DRAIN
6 DK-NNN DKNNN-BV-115 4" BALL VALVE POTABLE CONNECTION
7 DK-NNN DKNNN-BV-117 4" BALL VALVE POTABLE CONNECTION
POTABLE CONNECTION-
8 DK-NNN DKNNN-BV-118 1" BALL VALVE
DRAIN
9 DK-NNN DKNNN-BV-119 4" BALL VALVE POTABLE CONNECTION
10 DK-NNN DKNNN-BV-121 1" BALL VALVE PI-104 ISOLATION
11 DK-NNN DKNNN-BV-123 1" BALL VALVE PIT-104 ISOLATION
12 DK-NNN DKNNN-GLV-125 2" GLOBE VALVE BLEED LINE
13 DK-NNN DKNNN-BV-126 1" BALL VALVE PI-105 ISOLATION
14 DK-NNN DKNNN-BV-128 1" BALL VALVE PIT-105 ISOLATION
15 DK-NNN DKNNN-GLV-130 2" GLOBE VALVE BLEED LINE
16 DK-NNN DKNNN-BV-131 1" BALL VALVE PI-106 ISOLATION
17 DK-NNN DKNNN-BV-133 1" BALL VALVE PIT-106 ISOLATION
18 DK-NNN DKNNN-GLV-135 2" GLOBE VALVE BLEED LINE
19 DK-NNN DKNNN-BV-136 1" BALL VALVE BLEED VENT LINE
20 DK-NNN DKNNN-GLV-137 2" GLOBE VALVE BLEED LINE
21 DK-NNN DKNNN-GLV-138 2" GLOBE VALVE BLEED LINE
22 DK-NNN DKNNN-GLV-142 2" GLOBE VALVE BLEED LINE
23 DK-NNN DKNNN-NLV-107 1/2" NEEDLE VALVE SAMPLE POINT DRAIN
POTABLE END
24 DK-NNN DKNNN-NLV-116 1/2" NEEDLE VALVE
CONNECTION
POTABLE END
25 DK-NNN DKNNN-NLV-120 1/2" NEEDLE VALVE
CONNECTION
26 DK-NNN DKNNN-GV-102 2" GATE VALVE PIT-101 ISOLATION
27 DK-NNN DKNNN-GV-104 2" GATE VALVE PI-103 ISOLATION
28 DK-NNN DKNNN-GV-106 2" GATE VALVE SAMPLE POINT DRAIN

Doc. No.: QP-ENG-LST-013-008 Rev. 00 Date: 01/07/2019 Page 69 of 86

 QP STANDARD FOR EQUIPMENT IDENTIFICATION AND TAG
NUMBERING SYSTEM – DUKHAN FIELDS
DOC. No. QP-ENG-STD-013 Rev. 00

APPENDIX I1: OIL WELLS – TYPE 1 WITH HYDRAULIC WELLHEAD CONTROL

PANEL, PRESSURE BLEED LINE WITH GLV VALVES (Contd.)
MECHANICAL TYPICAL TAGS FOR OIL WELLS (Continuation)
SI. WELL
TAG NUMBER SIZE VALVE TYPE LOCATION REMARKS
NO. NO.
WHCP PANEL
29 DK-NNN DKNNN-GV-108 2" GATE VALVE
CONNECTION
30 DK-NNN DKNNN-GV-140 2" GATE VALVE PI-103 ISOLATION
MAIN PRODUCTION
DOUBLE BLOCK &
31 DK-NNN DKNNN-DBV-103 2.1/16"x1/2" LINE BELOW PIT
BLEED VALVE
CONNECTION
MAIN PRODUCTION
DOUBLE BLOCK &
32 DK-NNN DKNNN-DBV-105 2.1/16"x1/2" LINE BELOW PI
BLEED VALVE
CONNECTION
DOUBLE BLOCK & WHCP PANEL
33 DK-NNN DKNNN-DBV-109 2"
BLEED VALVE CONNECTION
DOUBLE BLOCK &
34 DK-NNN DKNNN-DBV-122 1"x1/2" PI-104 ISOLATION
BLEED VALVE
DOUBLE BLOCK &
35 DK-NNN DKNNN-DBV-124 1"x1/2" PIT-104 ISOLATION
BLEED VALVE
DOUBLE BLOCK &
36 DK-NNN DKNNN-DBV-127 1"x1/2" PI-105 ISOLATION
BLEED VALVE
DOUBLE BLOCK &
37 DK-NNN DKNNN-DBV-129 1"x1/2" PIT-105 ISOLATION
BLEED VALVE
DOUBLE BLOCK &
38 DK-NNN DKNNN-DBV-132 1"x1/2" PI-106 ISOLATION
BLEED VALVE
DOUBLE BLOCK &
39 DK-NNN DKNNN-DBV-134 1"x1/2" PIT-106 ISOLATION
BLEED VALVE
DOUBLE BLOCK & MAIN PRODUCTION
40 DK-NNN DKNNN-DBV-141 2.1/16"x1/2"
BLEED VALVE LINE INSIDE FENCE
41 DK-NNN DKNNN-CHV-101 4.1/16" CHOKE VALVE CHOKE VALVE
CORROSION MAIN PRODUCTION
42 DK-NNN DKNNN-CC-101 2"
COUPON LINE
SHUTDOWN MAIN PRODUCTION
43 DKNNN DKNNN-SDV-101 4.1/16”
VALVE LINE

INSTRUMENTATION TYPICAL TAGS FOR OIL WELLS

SI. WELL
TAG NUMBER SIZE VALVE TYPE LOCATION REMARKS
NO. NO.
PRESSURE
44 DKNNN DKNNN-PI-101 - ABOVE X-MAS TREE
INDICATOR
PRESSURE MAIN PRODCTION
45 DKNNN DKNNN-PI-103 -
INDICATOR LINE INSIDE FENCE
PRESSURE
46 DKNNN DKNNN-PI-104 - BLEED LINE
INDICATOR
PRESSURE
47 DKNNN DKNNN-PI-105 - BLEED LINE
INDICATOR
PRESSURE
48 DKNNN DKNNN-PI-106 - BLEED LINE
INDICATOR
PRESSURE
MAIN PRODUCTION
49 DKNNN DKNNN-PIT-101 - INDICATING
LINE
TRANSMITTER

Doc. No.: QP-ENG-LST-013-008 Rev. 00 Date: 01/07/2019 Page 70 of 86

 QP STANDARD FOR EQUIPMENT IDENTIFICATION AND TAG
NUMBERING SYSTEM – DUKHAN FIELDS
DOC. No. QP-ENG-STD-013 Rev. 00

APPENDIX I1: OIL WELLS – TYPE 1 WITH HYDRAULIC WELLHEAD CONTROL

PANEL, PRESSURE BLEED LINE WITH GLV VALVES (Contd.)
INSTRUMENTATION TYPICAL TAGS FOR OIL WELLS (Continuation)
SI. WELL
TAG NUMBER SIZE VALVE TYPE LOCATION REMARKS
NO. NO.
PRESSURE
MAIN PRODUCTION
50 DKNNN DKNNN-PIT-103 - INDICATING
LINE
TRANSMITTER
PRESSURE
51 DKNNN DKNNN-PIT-104 - INDICATING BLEED LINE
TRANSMITTER
PRESSURE
52 DKNNN DKNNN-PIT-105 - INDICATING BLEED LINE
TRANSMITTER
PRESSURE
53 DKNNN DKNNN-PIT-106 - INDICATING BLEED LINE
TRANSMITTER
TEMPATURE
MAIN PRODUCTION
54 DKNNN DKNNN-TIT-101 - INDICATING
LINE
TRANSMITTER
TEMPATURE MAIN PRODUCTION
55 DKNNN DKNNN-TE-101 -
ELEMENT LINE
MAIN PRODUCTION
56 DKNNN DKNNN-TW-101 - THERMOWELL
LINE
RESTRICTION
57 DKNNN DKNNN-RO-101 - BLEED LINE
ORIFICE
RESTRICTION
58 DKNNN DKNNN-RO-102 - BLEED LINE
ORIFICE
RESTRICTION
59 DKNNN DKNNN-RO-103 - BLEED LINE
ORIFICE
60 DKNNN DKNNN-PI-102 - PDHG SYSTEM WELLHEAD FENCE

61 DKNNN DKNNN-TI-102 - PDHG SYSTEM WELLHEAD FENCE

INSIDE WELLHEAD
62 DKNNN DKNNN-GDA-101 - USGD DETECTORS
FENCE
INSIDE WELLHEAD
62 DKNNN DKNNN-GDA-102 - USGD DETECTORS
FENCE
INSIDE WELLHEAD
62 DKNNN DKNNN-GDA-103 - USGD DETECTORS
FENCE
INSIDE WELLHEAD
63 DKNNN DKNNN-LP-101 - WHCP PANEL
FENCE

Doc. No.: QP-ENG-LST-013-008 Rev. 00 Date: 01/07/2019 Page 71 of 86

 QP STANDARD FOR EQUIPMENT IDENTIFICATION AND TAG
NUMBERING SYSTEM – DUKHAN FIELDS
DOC. No. QP-ENG-STD-013 Rev. 00

APPENDIX I2: OIL WELLS – TYPE 2 WITH HYDRAULIC WELLHEAD CONTROL

PANEL, PRESSURE BLEED LINE WITH BV VALVES
MECHANICAL TYPICAL TAGS FOR OIL WELLS
SI. WELL
TAG NUMBER SIZE VALVE TYPE LOCATION REMARKS
NO. NO.
MAIN PRODUCTION LINE
1 DK-NNN DKNNN-BV-110 6" BALL VALVE
NEAR WELLHEAD FENCE
MAIN PRODUCTION LINE
2 DK-NNN DKNNN-BV-111 6" BALL VALVE
NEAR WELLHEAD FENCE
3 DK-NNN DKNNN-BV-112 1" BALL VALVE PRODUCTION DRAIN

4 DK-NNN DKNNN-BV-113 4" BALL VALVE POTABLE CONNECTION

POTABLE CONNECTION-
5 DK-NNN DKNNN-BV-114 1" BALL VALVE
DRAIN
6 DK-NNN DKNNN-BV-115 4" BALL VALVE POTABLE CONNECTION

7 DK-NNN DKNNN-BV-117 4" BALL VALVE POTABLE CONNECTION

POTABLE CONNECTION-
8 DK-NNN DKNNN-BV-118 1" BALL VALVE
DRAIN
9 DK-NNN DKNNN-BV-119 4" BALL VALVE POTABLE CONNECTION

10 DK-NNN DKNNN-BV-121 1" BALL VALVE PI-104 ISOLATION

11 DK-NNN DKNNN-BV-123 1" BALL VALVE PIT-104 ISOLATION

12 DK-NNN DKNNN-BV-125 2" BALL VALVE BLEED LINE

13 DK-NNN DKNNN-BV-126 1" BALL VALVE PI-105 ISOLATION

14 DK-NNN DKNNN-BV-128 1" BALL VALVE PIT-105 ISOLATION

15 DK-NNN DKNNN-BV-130 2" BALL VALVE BLEED LINE

16 DK-NNN DKNNN-BV-131 1" BALL VALVE PI-106 ISOLATION

17 DK-NNN DKNNN-BV-133 1" BALL VALVE PIT-106 ISOLATION

18 DK-NNN DKNNN-BV-135 2" BALL VALVE BLEED LINE

19 DK-NNN DKNNN-BV-136 1" BALL VALVE BLEED VENT LINE

20 DK-NNN DKNNN-BV-137 2" BALL VALVE BLEED LINE

21 DK-NNN DKNNN-BV-138 2" BALL VALVE BLEED LINE

22 DK-NNN DKNNN-BV-142 2" BALL VALVE BLEED LINE

23 DK-NNN DKNNN-NLV-107 1/2" NEEDLE VALVE SAMPLE POINT DRAIN

24 DK-NNN DKNNN-NLV-116 1/2" NEEDLE VALVE POTABLE END CONNECTION

25 DK-NNN DKNNN-NLV-120 1/2" NEEDLE VALVE POTABLE END CONNECTION

26 DK-NNN DKNNN-GV-102 2" GATE VALVE PIT-101 ISOLATION

27 DK-NNN DKNNN-GV-104 2" GATE VALVE PI-103 ISOLATION

28 DK-NNN DKNNN-GV-106 2" GATE VALVE SAMPLE POINT DRAIN

Doc. No.: QP-ENG-LST-013-009 Rev. 00 Date: 01/07/2019 Page 72 of 86

 QP STANDARD FOR EQUIPMENT IDENTIFICATION AND TAG
NUMBERING SYSTEM – DUKHAN FIELDS
DOC. No. QP-ENG-STD-013 Rev. 00

APPENDIX I2: OIL WELLS – TYPE 2 WITH HYDRAULIC WELLHEAD CONTROL

PANEL, PRESSURE BLEED LINE WITH BV VALVES (Contd.)
MECHANICAL TYPICAL TAGS FOR OIL WELLS (Continuation)
SI. WELL
TAG NUMBER SIZE VALVE TYPE LOCATION REMARKS
NO. NO.
29 DK-NNN DKNNN-GV-108 2" GATE VALVE WHCP PANEL CONNECTION

30 DK-NNN DKNNN-GV-140 2" GATE VALVE PI-103 ISOLATION

2.1/16" DOUBLE BLOCK MAIN PRODUCTION LINE
31 DK-NNN DKNNN-DBV-103
x1/2" & BLEED VALVE BELOW PIT CONNECTION
2.1/16" DOUBLE BLOCK MAIN PRODUCTION LINE
32 DK-NNN DKNNN-DBV-105
x1/2" & BLEED VALVE BELOW PI CONNECTION
DOUBLE BLOCK
33 DK-NNN DKNNN-DBV-109 2" WHCP PANEL CONNECTION
& BLEED VALVE
DOUBLE BLOCK
34 DK-NNN DKNNN-DBV-122 1"x1/2" PI-104 ISOLATION
& BLEED VALVE
DOUBLE BLOCK
35 DK-NNN DKNNN-DBV-124 1"x1/2" PIT-104 ISOLATION
& BLEED VALVE
DOUBLE BLOCK
36 DK-NNN DKNNN-DBV-127 1"x1/2" PI-105 ISOLATION
& BLEED VALVE
DOUBLE BLOCK
37 DK-NNN DKNNN-DBV-129 1"x1/2" PIT-105 ISOLATION
& BLEED VALVE
DOUBLE BLOCK
38 DK-NNN DKNNN-DBV-132 1"x1/2" PI-106 ISOLATION
& BLEED VALVE
DOUBLE BLOCK
39 DK-NNN DKNNN-DBV-134 1"x1/2" PIT-106 ISOLATION
& BLEED VALVE
2.1/16" DOUBLE BLOCK MAIN PRODUCTION LINE
40 DK-NNN DKNNN-DBV-141
x1/2" & BLEED VALVE INSIDE FENCE
41 DK-NNN DKNNN-CHV-101 4.1/16" CHOKE VALVE CHOKE VALVE
CORROSION
42 DK-NNN DKNNN-CC-101 2" MAIN PRODUCTION LINE
COUPON
SHUTDOWN
43 DKNNN DKNNN-SDV-101 4.1/16” MAIN PRODUCTION LINE
VALVE

INSTRUMENTATION TYPICAL TAGS FOR OIL WELLS

SI. WELL
TAG NUMBER SIZE VALVE TYPE LOCATION REMARKS
NO. NO.
PRESSURE
44 DKNNN DKNNN-PI-101 - ABOVE X-MAS TREE
INDICATOR
PRESSURE MAIN PRODCTION LINE
45 DKNNN DKNNN-PI-103 -
INDICATOR INSIDE FENCE
PRESSURE
46 DKNNN DKNNN-PI-104 - BLEED LINE
INDICATOR
PRESSURE
47 DKNNN DKNNN-PI-105 - BLEED LINE
INDICATOR
PRESSURE
48 DKNNN DKNNN-PI-106 - BLEED LINE
INDICATOR
PRESSURE
49 DKNNN DKNNN-PIT-101 - INDICATING MAIN PRODUCTION LINE
TRANSMITTER
PRESSURE
50 DKNNN DKNNN-PIT-103 - INDICATING MAIN PRODUCTION LINE
TRANSMITTER

Doc. No.: QP-ENG-LST-013-009 Rev. 00 Date: 01/07/2019 Page 73 of 86

 QP STANDARD FOR EQUIPMENT IDENTIFICATION AND TAG
NUMBERING SYSTEM – DUKHAN FIELDS
DOC. No. QP-ENG-STD-013 Rev. 00

APPENDIX I2: OIL WELLS – TYPE 2 WITH HYDRAULIC WELLHEAD CONTROL

PANEL, PRESSURE BLEED LINE WITH BV VALVES (Contd.)
INSTRUMENTATION TYPICAL TAGS FOR OIL WELLS
SI. WELL
TAG NUMBER SIZE VALVE TYPE LOCATION REMARKS
NO. NO.
PRESSURE
51 DKNNN DKNNN-PIT-104 - INDICATING BLEED LINE
TRANSMITTER
PRESSURE
52 DKNNN DKNNN-PIT-105 - INDICATING BLEED LINE
TRANSMITTER
PRESSURE
53 DKNNN DKNNN-PIT-106 - INDICATING BLEED LINE
TRANSMITTER
TEMPATURE
54 DKNNN DKNNN-TIT-101 - INDICATING MAIN PRODUCTION LINE
TRANSMITTER
TEMPATURE
55 DKNNN DKNNN-TE-101 - MAIN PRODUCTION LINE
ELEMENT
56 DKNNN DKNNN-TW-101 - THERMOWELL MAIN PRODUCTION LINE
RESTRICTION
57 DKNNN DKNNN-RO-101 - BLEED LINE
ORIFICE
RESTRICTION
58 DKNNN DKNNN-RO-102 - BLEED LINE
ORIFICE
RESTRICTION
59 DKNNN DKNNN-RO-103 - BLEED LINE
ORIFICE
60 DKNNN DKNNN-PI-102 - PDHG SYSTEM WELLHEAD FENCE

61 DKNNN DKNNN-TI-102 - PDHG SYSTEM WELLHEAD FENCE

USGD
62 DKNNN DKNNN-GDA-101 - INSIDE WELLHEAD FENCE
DETECTORS
USGD
62 DKNNN DKNNN-GDA-102 - INSIDE WELLHEAD FENCE
DETECTORS
USGD
62 DKNNN DKNNN-GDA-103 - INSIDE WELLHEAD FENCE
DETECTORS
63 DKNNN DKNNN-LP-101 - WHCP PANEL INSIDE WELLHEAD FENCE

Doc. No.: QP-ENG-LST-013-009 Rev. 00 Date: 01/07/2019 Page 74 of 86

 QP STANDARD FOR EQUIPMENT IDENTIFICATION AND TAG
NUMBERING SYSTEM – DUKHAN FIELDS
DOC. No. QP-ENG-STD-013 Rev. 00

APPENDIX I3: OIL WELLS – TYPE 3 WITHOUT HYDRAULIC WELLHEAD CONTROL

PANEL, PRESSURE BLEED LINE WITH BV VALVES
MECHANICAL TYPICAL TAGS FOR OIL WELLS
SI. WELL
TAG NUMBER SIZE VALVE TYPE LOCATION REMARKS
NO. NO.
MAIN PRODUCTION LINE NEAR
1 DK-NNN DKNNN-BV-110 6" BALL VALVE
WELLHEAD FENCE
MAIN PRODUCTION LINE NEAR
2 DK-NNN DKNNN-BV-111 6" BALL VALVE
WELLHEAD FENCE
3 DK-NNN DKNNN-BV-112 1" BALL VALVE PRODUCTION DRAIN

4 DK-NNN DKNNN-BV-113 4" BALL VALVE POTABLE CONNECTION

5 DK-NNN DKNNN-BV-114 1" BALL VALVE POTABLE CONNECTION-DRAIN

6 DK-NNN DKNNN-BV-115 4" BALL VALVE POTABLE CONNECTION

7 DK-NNN DKNNN-BV-117 4" BALL VALVE POTABLE CONNECTION

8 DK-NNN DKNNN-BV-118 1" BALL VALVE POTABLE CONNECTION-DRAIN

9 DK-NNN DKNNN-BV-119 4" BALL VALVE POTABLE CONNECTION

10 DK-NNN DKNNN-BV-121 1" BALL VALVE PI-104 ISOLATION

11 DK-NNN DKNNN-BV-123 1" BALL VALVE PIT-104 ISOLATION

12 DK-NNN DKNNN-BV-125 2" BALL VALVE BLEED LINE

13 DK-NNN DKNNN-BV-126 1" BALL VALVE PI-105 ISOLATION

14 DK-NNN DKNNN-BV-128 1" BALL VALVE PIT-105 ISOLATION

15 DK-NNN DKNNN-BV-130 2" BALL VALVE BLEED LINE

16 DK-NNN DKNNN-BV-131 1" BALL VALVE PI-106 ISOLATION

17 DK-NNN DKNNN-BV-133 1" BALL VALVE PIT-106 ISOLATION

18 DK-NNN DKNNN-BV-135 2" BALL VALVE BLEED LINE

19 DK-NNN DKNNN-BV-136 1" BALL VALVE BLEED VENT LINE

20 DK-NNN DKNNN-BV-137 2" BALL VALVE BLEED LINE

21 DK-NNN DKNNN-BV-138 2" BALL VALVE BLEED LINE

22 DK-NNN DKNNN-BV-142 2" BALL VALVE BLEED LINE

23 DK-NNN DKNNN-NLV-107 1/2" NEEDLE VALVE SAMPLE POINT DRAIN

24 DK-NNN DKNNN-NLV-116 1/2" NEEDLE VALVE POTABLE END CONNECTION

25 DK-NNN DKNNN-NLV-120 1/2" NEEDLE VALVE POTABLE END CONNECTION

26 DK-NNN DKNNN-GV-102 2" GATE VALVE PIT-101 ISOLATION

27 DK-NNN DKNNN-GV-104 2" GATE VALVE PI-103 ISOLATION

28 DK-NNN DKNNN-GV-106 2" GATE VALVE SAMPLE POINT DRAIN

Doc. No.: QP-ENG-LST-013-010 Rev. 00 Date: 01/07/2019 Page 75 of 86

 QP STANDARD FOR EQUIPMENT IDENTIFICATION AND TAG
NUMBERING SYSTEM – DUKHAN FIELDS
DOC. No. QP-ENG-STD-013 Rev. 00

APPENDIX I3: OIL WELLS – TYPE 3 WITHOUT HYDRAULIC WELLHEAD CONTROL

PANEL, PRESSURE BLEED LINE WITH BV VALVES (Contd.)

MECHANICAL TYPICAL TAGS FOR OIL WELLS (Continuation)

SI. WELL
NO. NO.
TAG NUMBER SIZE VALVE TYPE LOCATION REMARKS
29 DK-NNN DKNNN-GV-140 2" GATE VALVE PI-103 ISOLATION
MAIN PRODUCTION
DOUBLE BLOCK
30 DK-NNN DKNNN-DBV-103 2.1/16"x1/2" LINE BELOW PIT
& BLEED VALVE
CONNECTION
MAIN PRODUCTION
DOUBLE BLOCK
31 DK-NNN DKNNN-DBV-105 2.1/16"x1/2" LINE BELOW PI
& BLEED VALVE
CONNECTION
DOUBLE BLOCK
32 DK-NNN DKNNN-DBV-122 1"x1/2" PI-104 ISOLATION
& BLEED VALVE
DOUBLE BLOCK
33 DK-NNN DKNNN-DBV-124 1"x1/2" PIT-104 ISOLATION
& BLEED VALVE
DOUBLE BLOCK
34 DK-NNN DKNNN-DBV-127 1"x1/2" PI-105 ISOLATION
& BLEED VALVE
DOUBLE BLOCK
35 DK-NNN DKNNN-DBV-129 1"x1/2" PIT-105 ISOLATION
& BLEED VALVE
DOUBLE BLOCK
36 DK-NNN DKNNN-DBV-132 1"x1/2" PI-106 ISOLATION
& BLEED VALVE
DOUBLE BLOCK
37 DK-NNN DKNNN-DBV-134 1"x1/2" PIT-106 ISOLATION
& BLEED VALVE
2.1/16" DOUBLE BLOCK MAIN PRODUCTION
38 DK-NNN DKNNN-DBV-141
x1/2" & BLEED VALVE LINE INSIDE FENCE
39 DK-NNN DKNNN-CHV-101 4.1/16" CHOKE VALVE CHOKE VALVE
CORROSION MAIN PRODUCTION
40 DK-NNN DKNNN-CC-101 2"
COUPON LINE
SHUTDOWN MAIN PRODUCTION
41 DKNNN DKNNN-SDV-101 4.1/16”
VALVE LINE

INSTRUMENTATION TYPICAL TAGS FOR OIL WELLS

SI. WELL
TAG NUMBER SIZE VALVE TYPE LOCATION REMARKS
NO. NO.
ABOVE X-MAS
42 DKNNN DKNNN-PI-101 - PRESSURE INDICATOR
TREE
MAIN PRODCTION
43 DKNNN DKNNN-PI-103 - PRESSURE INDICATOR
LINE INSIDE FENCE
44 DKNNN DKNNN-PI-104 - PRESSURE INDICATOR BLEED LINE

45 DKNNN DKNNN-PI-105 - PRESSURE INDICATOR BLEED LINE

46 DKNNN DKNNN-PI-106 - PRESSURE INDICATOR BLEED LINE

PRESSURE INDICATING MAIN PRODUCTION
47 DKNNN DKNNN-PIT-101 -
TRANSMITTER LINE
PRESSURE INDICATING MAIN PRODUCTION
48 DKNNN DKNNN-PIT-103 -
TRANSMITTER LINE
PRESSURE INDICATING
49 DKNNN DKNNN-PIT-104 - BLEED LINE
TRANSMITTER

Doc. No.: QP-ENG-LST-013-010 Rev. 00 Date: 01/07/2019 Page 76 of 86

 QP STANDARD FOR EQUIPMENT IDENTIFICATION AND TAG
NUMBERING SYSTEM – DUKHAN FIELDS
DOC. No. QP-ENG-STD-013 Rev. 00

APPENDIX I3: OIL WELLS – TYPE 3 WITHOUT HYDRAULIC WELLHEAD CONTROL

PANEL, PRESSURE BLEED LINE WITH BV VALVES (Contd.)

INSTRUMENTATION TYPICAL TAGS FOR OIL WELLS

SI. WELL
TAG NUMBER SIZE VALVE TYPE LOCATION REMARKS
NO. NO.
PRESSURE INDICATING
50 DKNNN DKNNN-PIT-105 - BLEED LINE
TRANSMITTER
PRESSURE INDICATING
51 DKNNN DKNNN-PIT-106 - BLEED LINE
TRANSMITTER
TEMPATURE INDICATING MAIN
52 DKNNN DKNNN-TIT-101 -
TRANSMITTER PRODUCTION LINE
MAIN
53 DKNNN DKNNN-TE-101 - TEMPATURE ELEMENT
PRODUCTION LINE
MAIN
54 DKNNN DKNNN-TW-101 - THERMOWELL
PRODUCTION LINE
55 DKNNN DKNNN-RO-101 - RESTRICTION ORIFICE BLEED LINE
56 DKNNN DKNNN-RO-102 - RESTRICTION ORIFICE BLEED LINE
56 DKNNN DKNNN-RO-103 - RESTRICTION ORIFICE BLEED LINE
58 DKNNN DKNNN-PI-102 - PDHG SYSTEM WELLHEAD FENCE
59 DKNNN DKNNN-TI-102 - PDHG SYSTEM WELLHEAD FENCE

Doc. No.: QP-ENG-LST-013-010 Rev. 00 Date: 01/07/2019 Page 77 of 86

 QP STANDARD FOR EQUIPMENT IDENTIFICATION AND TAG NUMBERING SYSTEM – DUKHAN FIELDS

DOC. No. QP-ENG-STD-013 Rev. 00

APPENDIX J1: POWER WATER INJECTION – TYPICAL WELLHEAD (TYPE-1) P&ID

Sample Only

Doc. No.: QP-ENG-STD-013 Rev. 00 Date: 01/07/2019 Page 78 of 86

 QP STANDARD FOR EQUIPMENT IDENTIFICATION AND TAG NUMBERING SYSTEM – DUKHAN FIELDS

DOC. No. QP-ENG-STD-013 Rev. 00

APPENDIX J2: POWER WATER INJECTION – TYPICAL WELLHEAD (TYPE-2) P&ID

Sample Only

Doc. No.: QP-ENG-STD-013 Rev. 00 Date: 01/07/2019 Page 79 of 86

 QP STANDARD FOR EQUIPMENT IDENTIFICATION AND TAG NUMBERING SYSTEM – DUKHAN FIELDS

DOC. No. QP-ENG-STD-013 Rev. 00

APPENDIX K: GAS LIFT WELL – TYPICAL WELLHEAD (WITHOUT WHCP) P&ID

Sample Only

Doc. No.: QP-ENG-STD-013 Rev. 00 Date: 01/07/2019 Page 80 of 86

 QP STANDARD FOR EQUIPMENT IDENTIFICATION AND TAG NUMBERING SYSTEM – DUKHAN FIELDS

DOC. No. QP-ENG-STD-013 Rev. 00

APPENDIX L: WATER SOURCE WELL – TYPICAL WELLHEAD P&ID

Sample Only

Doc. No.: QP-ENG-STD-013 Rev. 00 Date: 01/07/2019 Page 81 of 86

 QP STANDARD FOR EQUIPMENT IDENTIFICATION AND TAG NUMBERING SYSTEM – DUKHAN FIELDS

DOC. No. QP-ENG-STD-013 Rev. 00

APPENDIX M: RE-CIRCULATION WELL – TYPICAL WELLHEAD P&ID

Sample Only

Doc. No.: QP-ENG-STD-013 Rev. 00 Date: 01/07/2019 Page 82 of 86

 QP STANDARD FOR EQUIPMENT IDENTIFICATION AND TAG NUMBERING SYSTEM – DUKHAN FIELDS

DOC. No. QP-ENG-STD-013 Rev. 00

APPENDIX N1: OIL WELL – TYPICAL WELLHEAD (TYPE-1) P&ID

Sample Only
Sample Only

Doc. No.: QP-ENG-STD-013 Rev. 00 Date: 01/07/2019 Page 83 of 86

 QP STANDARD FOR EQUIPMENT IDENTIFICATION AND TAG NUMBERING SYSTEM – DUKHAN FIELDS

DOC. No. QP-ENG-STD-013 Rev. 00

APPENDIX N2: OIL WELL – TYPICAL WELLHEAD (TYPE-2) P&ID

Sample Only

Doc. No.: QP-ENG-STD-013 Rev. 00 Date: 01/07/2019 Page 84 of 86

 QP STANDARD FOR EQUIPMENT IDENTIFICATION AND TAG NUMBERING SYSTEM – DUKHAN FIELDS

DOC. No. QP-ENG-STD-013 Rev. 00

APPENDIX N3: OIL WELL – TYPICAL WELLHEAD (TYPE-3) P&ID

Sample Only

Doc. No.: QP-ENG-STD-013 Rev. 00 Date: 01/07/2019 Page 85 of 86

 QP STANDARD FOR EQUIPMENT IDENTIFICATION AND TAG
NUMBERING SYSTEM – DUKHAN FIELDS

DOC. No. QP-ENG-STD-013 Rev. 00

REVISION HISTORY LOG

Item Revised Revision Description Page No.

QPR-DKN-05 Rev.0 New Procedure All
Dated 02.09.2004
QPR-DKN-05 Rev.01 Updated All Departments 0All Dept.
Dated 18.06.2009
QPR-DKN-05 Rev.02 General Update All
Dated 02.05.2012
QPR-DKN-05 Rev.03 General Update All
Dated 04.01.2017
QP-ENG-STD-013 Assigned a new document number and issued All
Rev.00 Dated 29.05.2019 as Rev.00 to align with QP-IMS-PRC-001.
Document replaces QPR-DKN-005.

Remarks :
Nil.

Doc. No.: QP-ENG-STD-013 Rev. 00 Date: 01/07/2019 Page 86 of 86