ELTRAC ET-TN-445-87 - Trakker E4 Error Codes Page 2 of 30

ECU Reference Document Date

ABS (Wabco) E-SIDFMI-RSAC_050902b_ErrorList.pdf 05.09.2002
Additional Heater Air (AHTa) IC Texts table rev 6.0.xls 01.06.2007
Eberspaecher
Additional Heater Water (AHTw) IC Texts table rev 6.0.xls 01.06.2007
Automatic DriveTrain Management ADM Failure Codes V4.1.doc
(ADM)
Allison Gen4 Datalink Tech Data 27.10.2004
Allison 4th generation controls - Model Jear 2006
Climate Automatic Control (CLC) IC Texts table rev 6.0.xls 01.06.2007
CoDriver Door Module (CDM) IC Texts table rev 6.0.xls 01.06.2007
Driver Door Module (DDM) IC Texts table rev 6.0.xls 01.06.2007
DTCO DTCO 1381 ISO CAN Interface_Spec_05_2004.pdf 01.05.2004
ECAS 446 170 211 0-435.pdf 07.06.2005
ECM F&R_P340v91_NEF_4Cyl_EuroCargo_E4&5.xls (fbyrbn03_ec7) 08.08.2006
ECM FnR_P340vA0_NEF6Cyl_EuroCargo_E4_5_FullOBD_wPerfLi-0_0 - 15.06.2007
hhuwbq01_ef1_trimmed
ECM FnR_P342vA0_Cursor8_Trakker_E4_5_FullOBD_VGT - C8_Trakker_265F_VGT 14.06.2007
ECM FnR_P342vA0_Cursor8_Trakker_E4_5_FullOBD_WG - C8_Trakker_228F_WG 14.06.2007
ECM FnR_P342vA0_Cursor13_Trakker_E4_5_FullOBD_VGT - VA0Trakker_368F5_30l 14.06.2007
ECM FnR_P342vA0_Cursor13_Trakker_E4_5_FullOBD_WG - C13_Trakker_301F5_WG 15.06.2007
ECM FnR_P342vA0_Cursor13_TrakkerMilitare_E4_5_FullOBD - C13_Militare_368M5 15.06.2007
Eurotronic 2 IC Texts table rev 6.0.xls 01.06.2007
Expansion Module (EM) EM_WP1_rel1 DTC list_vDRAFT.xls 23.02.2006
IBC3 ET-SP-445-43v31 - IBC3 for Iveco Vehicles.doc 24.07.2007
IC M06 ET-SP-439-20v23 - Instrument Cluster with Monochrome Display.doc 02.11.2006
IC M06 MY2008 ET-SP-439-20v31 - Instrument Cluster with Monochrome Display.doc 22.11.2007
Per Eurocargo MY2008.
Intarder IC Texts table rev 6.0.xls 01.06.2007
Steering Wheel Interface (SWI) IC Texts table rev 6.0.xls 01.06.2007
Modulo Elettronica Telaio (MET) ET-SP-445-53v30 - MET for Iveco Vehicles.doc 12.06.2007
MTCO VDO MTCO Pilot Documentation.pdf 01.03.2000
Urea Dosing System (UDS) F&R_DNOx2 HJ6ABAAQ_ECA_no calculations.xls 30.08.2007
UDS F&R_DNOx2 HJ6AB00Q_ECA_no calculations.xls (no heating) 30.08.2007
Vehicle Control Module (VCM) failure_management _2.52.xls 22.05.2007

Bianca Andreana Reference Doc Print Date: 21.11.2021

ELTRAC ET-TN-445-87 - Trakker E4 Error Codes Page 3 of 30

ECU SPN F au ltC o mp one n t D

es
crip
tio
n F MI F
M I C
omm
en
t L
amps
tat
u s M
ILL
amp
Na
m e [Hex] [
H e
x] D
es
crip
tio
n
ABS 40B01 Wheel sensor left front fault. air gap too large, sensor output voltage too low but just 01 air gap ABS: wheel disabled Yellow
exceeds trigger level ASR: disabled
ABS 40B01 Wheel sensor left front fault. such proportion of tyre diameter/ pole wheel teeth number that 02 incorrect tyre or pole wheel ABS: wheel disabled Yellow
wheel speed difference within front axle > 10 % or difference ASR: disabled
within wheels of different axles > 19 % . Pneus or number of
polewheel teeth are different.
Check wheel circumference and number of polewheel
ABS 40B01 Wheel sensor left front fault. DC voltage detected. Short circuit or impedance to battery 03 shorted to UBATT ABS: wheel disabled Yellow
voltage. ASR: disabled
ABS 40B01 Wheel sensor left front fault. Short circuit to ground is detected. 04 Short circuit to ground ABS: wheel disabled Yellow
ASR: disabled
ABS 40B01 Wheel sensor left front fault. Open circuit is detected 05 open circuit ABS: wheel disabled Yellow
ASR: disabled
ABS 40B01 Wheel sensor left front fault. Short circuit between sensorwires IG/IGM is detected 06 short circuit ABS: wheel disabled Yellow
ASR: disabled
ABS 40B01 Wheel sensor left front fault. Cyclic drop out detected at speed higher than 10 km/h. 07 incorrect pole wheel ABS: wheel disabled Yellow
Several wheel revolution necessary. ASR: disabled
ABS 40B01 Wheel sensor left front fault. 16 sec. slip duration detected. 08 slip ABS: wheel disabled Yellow
ASR: disabled
ABS 40B01 Wheel sensor left front fault. Wire IG or IGM of another sensor is detected. 09 wires mismatched ABS: wheel disabled Yellow
ASR: disabled
ABS 40B01 Wheel sensor left front fault. Temporarily loss of wheel speed signal. Air gap too large, 0A speed drop-out ABS: wheel disabled Yellow
sensor voltage exceeds trigger level at too late. ASR: disabled
ABS 40B01 Wheel sensor left front fault. Brake squeezes or chatters. 0B abnormal speed (chatter)not stored ABS: partial disabled Yellow
ASR: disabled with standard
parameter set not as fault
interpretated
FMI 11 not stored
ABS 40B01 Wheel sensor left front fault. Not plausible sensor frequency measured 0C frequency too high ABS: wheel disabled Yellow
ASR: disabled
ABS 40B02 Wheel sensor right front fault air gap too large, sensor output voltage too low but just 01 air gap ABS: wheel disabled Yellow
exceeds trigger level ASR: disabled
ABS 40B02 Wheel sensor right front fault such proportion of tyre diameter/ pole wheel teeth number that 02 incorrect tyre or pole wheel ABS: wheel disabled Yellow
wheel speed difference within front axle > 10 % or difference ASR: disabled
within wheels of different axles > 19 % . Pneus or number of
polewheel teeth are different.
Check wheel circumference and number of polewheel
ABS 40B02 Wheel sensor right front fault DC voltage detected. Short circuit or impedance to battery 03 shorted to UBATT ABS: wheel disabled Yellow
voltage. ASR: disabled
ABS 40B02 Wheel sensor right front fault Short circuit to ground is detected. 04 Short circuit to ground ABS: wheel disabled Yellow
ASR: disabled
ABS 40B02 Wheel sensor right front fault Open circuit is detected 05 open circuit ABS: wheel disabled Yellow
ASR: disabled
ABS 40B02 Wheel sensor right front fault Short circuit between sensorwires IG/IGM is detected 06 short circuit ABS: wheel disabled Yellow
ASR: disabled
ABS 40B02 Wheel sensor right front fault Cyclic drop out detected at speed higher than 10 km/h. 07 incorrect pole wheel ABS: wheel disabled Yellow
Several wheel revolution necessary. ASR: disabled
ABS 40B02 Wheel sensor right front fault 16 sec. slip duration detected. 08 slip ABS: wheel disabled Yellow
ASR: disabled
ABS 40B02 Wheel sensor right front fault Wire IG or IGM of another sensor is detected. 09 wires mismatched ABS: wheel disabled Yellow
ASR: disabled
ABS 40B02 Wheel sensor right front fault Temporarily loss of wheel speed signal. Air gap too large, 0A speed drop-out ABS: wheel disabled Yellow
sensor voltage exceeds trigger level at too late. ASR: disabled
ABS 40B02 Wheel sensor right front fault Brake squeezes or chatters. 0B abnormal speed (chatter)not stored ABS: partial disabled Yellow
ASR: disabled with standard
parameter set not as fault
interpretated
FMI 11 not stored
ABS 40B02 Wheel sensor right front fault Not plausible sensor frequency measured 0C frequency too high ABS: wheel disabled Yellow
ASR: disabled
ABS 40B03 Wheel sensor left rear fault air gap too large, sensor output voltage too low but just 01 air gap ABS: wheel disabled Yellow
exceeds trigger level ASR: disabled
ABS 40B03 Wheel sensor left rear fault such proportion of tyre diameter/ pole wheel teeth number that 02 incorrect tyre or pole wheel ABS: wheel disabled Yellow
wheel speed difference within front axle > 10 % or difference ASR: disabled
within wheels of different axles > 19 % . Pneus or number of
polewheel teeth are different.
Check wheel circumference and number of polewheel
ABS 40B03 Wheel sensor left rear fault DC voltage detected. Short circuit or impedance to battery 03 shorted to UBATT ABS: wheel disabled Yellow
voltage. ASR: disabled
ABS 40B03 Wheel sensor left rear fault Short circuit to ground is detected. 04 Short circuit to ground ABS: wheel disabled Yellow
ASR: disabled
ABS 40B03 Wheel sensor left rear fault Open circuit is detected 05 open circuit ABS: wheel disabled Yellow
ASR: disabled
ABS 40B03 Wheel sensor left rear fault Short circuit between sensorwires IG/IGM is detected 06 short circuit ABS: wheel disabled Yellow
ASR: disabled
ABS 40B03 Wheel sensor left rear fault Cyclic drop out detected at speed higher than 10 km/h. 07 incorrect pole wheel ABS: wheel disabled Yellow
Several wheel revolution necessary. ASR: disabled
ABS 40B03 Wheel sensor left rear fault 16 sec. slip duration detected. 08 slip ABS: wheel disabled Yellow
ASR: disabled
ABS 40B03 Wheel sensor left rear fault Wire IG or IGM of another sensor is detected. 09 wires mismatched ABS: wheel disabled Yellow
ASR: disabled
ABS 40B03 Wheel sensor left rear fault Temporarily loss of wheel speed signal. Air gap too large, 0A speed drop-out ABS: wheel disabled Yellow
sensor voltage exceeds trigger level at too late. ASR: disabled
ABS 40B03 Wheel sensor left rear fault Brake squeezes or chatters. 0B abnormal speed (chatter)not stored ABS: wheel disabled Yellow
ASR: disabled
ABS 40B03 Wheel sensor left rear fault Not plausible sensor frequency measured 0C frequency too high ABS: wheel disabled Yellow
ASR: disabled
ABS 40B04 Wheel sensor right rear fault air gap too large, sensor output voltage too low but just 01 air gap ABS: wheel disabled Yellow
exceeds trigger level ASR: disabled
ABS 40B04 Wheel sensor right rear fault such proportion of tyre diameter/ pole wheel teeth number that 02 incorrect tyre or pole wheel ABS: wheel disabled Yellow
wheel speed difference within front axle > 10 % or difference ASR: disabled
within wheels of different axles > 19 % . Pneus or number of
polewheel teeth are different.
Check wheel circumference and number of polewheel
ABS 40B04 Wheel sensor right rear fault DC voltage detected. Short circuit or impedance to battery 03 shorted to UBATT ABS: wheel disabled Yellow
voltage. ASR: disabled
ABS 40B04 Wheel sensor right rear fault Short circuit to ground is detected. 04 Short circuit to ground ABS: wheel disabled Yellow
ASR: disabled
ABS 40B04 Wheel sensor right rear fault Open circuit is detected 05 open circuit ABS: wheel disabled Yellow
ASR: disabled
ABS 40B04 Wheel sensor right rear fault Short circuit between sensorwires IG/IGM is detected 06 short circuit ABS: wheel disabled Yellow
ASR: disabled
ABS 40B04 Wheel sensor right rear fault Cyclic drop out detected at speed higher than 10 km/h. 07 incorrect pole wheel ABS: wheel disabled Yellow
Several wheel revolution necessary. ASR: disabled
ABS 40B04 Wheel sensor right rear fault 16 sec. slip duration detected. 08 slip ABS: wheel disabled Yellow
ASR: disabled
ABS 40B04 Wheel sensor right rear fault Wire IG or IGM of another sensor is detected. 09 wires mismatched ABS: wheel disabled Yellow
ASR: disabled
ABS 40B04 Wheel sensor right rear fault Temporarily loss of wheel speed signal. Air gap too large, 0A speed drop-out ABS: wheel disabled Yellow
sensor voltage exceeds trigger level at too late. ASR: disabled
ABS 40B04 Wheel sensor right rear fault Brake squeezes or chatters. 0B abnormal speed (chatter)not stored ABS: wheel disabled Yellow
ASR: disabled
ABS 40B04 Wheel sensor right rear fault Not plausible sensor frequency measured 0C frequency too high ABS: wheel disabled Yellow
ASR: disabled
ABS 40B07 Modulator left front failure DC voltage detected. Short circuit or impedance to battery 03 shorted to UBATT ABS: disabled Yellow
voltage. ASR: disabled
SMR: disabled
EBL: disabled
ABS 40B07 Modulator left front failure Open circuit is detected 05 open circuit ABS: wheel disabled Yellow
ABS 40B07 Modulator left front failure Short circuit between sensorwires IG/IGM is detected 06 Short circuit to ground ABS: wheel disabled Yellow
ABS 40B08 Modulator right front failure DC voltage detected. Short circuit or impedance to battery 03 shorted to UBATT ABS: disabled Yellow
voltage. ASR: disabled
SMR: disabled
EBL: disabled
ABS 40B08 Modulator right front failure Open circuit is detected 05 open circuit ABS: wheel disabled Yellow
ABS 40B08 Modulator right front failure Short circuit between sensorwires IG/IGM is detected 06 Short circuit to ground ABS: wheel disabled Yellow
ABS 40B09 Modulator left rear failure DC voltage detected. Short circuit or impedance to battery 03 shorted to UBATT ABS: disabled Yellow
voltage. ASR: disabled
SMR: disabled
EBL: disabled
ABS 40B09 Modulator left rear failure Open circuit is detected 05 open circuit ABS: wheel disabled Yellow
ASR: Diff brake disabled
SMR: disabled
EBL: wheel disabled
ABS 40B09 Modulator left rear failure Short circuit between sensorwires IG/IGM is detected 06 Short circuit to ground ABS: wheel disabled Yellow
ASR: Diff brake disabled
SMR: disabled
EBL: wheel disabled
ABS 40B0A Modulator right rear failure DC voltage detected. Short circuit or impedance to battery 03 shorted to UBATT ABS: disabled Yellow
voltage. ASR: disabled
SMR: disabled
EBL: disabled
ABS 40B0A Modulator right rear failure Open circuit is detected 05 open circuit ABS: wheel disabled Yellow
ASR: Diff brake disabled
SMR: disabled
EBL: wheel disabled

Bianca Andreana Trakker E4 Errors list Print Date: 21.11.2021

ELTRAC ET-TN-445-87 - Trakker E4 Error Codes Page 4 of 30

ECU SPN Fau ltC o m p o nen

t D
es
crip
tio
n F MI FMI C
omm
en
t L
amps
tat
u s M
ILL
amp
Na
m e [Hex] [
H e
x] De scr
iptio
n
ABS 40B0A Modulator right rear failure Short circuit between sensorwires IG/IGM is detected 06 Short circuit to ground ABS: wheel disabled Yellow
ASR: Diff brake disabled
SMR: disabled
EBL: wheel disabled
ABS 40B0D DBR, Retarder DC voltage detected. Short circuit or impedance to battery 03 shorted to UBATT DBR control disabled Yellow
voltage.
ABS 40B0D DBR, Retarder Open circuit is detected 05 open circuit DBR control disabled Yellow
ABS 40B0D DBR, Retarder Short circuit between sensorwires IG/IGM is detected 06 Short circuit to ground DBR control disabled Yellow
ABS 40B0E ABS error. Short circuit to ground is detected. 04 Voltage, low voltage/open circuit ABS: disabled Yellow
ASR: disabled
SMR: disabled
EBL: disabled
ABS 40B0E ABS error. Open circuit is detected 05 WL-Ground ABS: disabled Yellow
ASR: disabled
SMR: disabled
EBL: disabled
ABS 40B0E ABS error. Cyclic drop out detected at speed higher than 10 km/h. 07 Valve Relay ABS: disabled Yellow
Several wheel revolution necessary. ASR: disabled
SMR: disabled
EBL: disabled
ABS 40B0F ABS error. DC voltage detected. Short circuit or impedance to battery 03 Voltage, low voltage/open circuit Dif&aux output disabled Yellow
voltage. ASR: Diff brake disabled
ABS 40B0F ABS error. Short circuit to ground is detected. 04 Voltage, low voltage/open circuit ABS: disabled Yellow
ASR: disabled
SMR: disabled
EBL: disabled
ABS 40B0F ABS error. Open circuit is detected 05 WL-Ground Dif&aux output disabled Yellow
ASR: Diff brake disabled
ABS 40B0F ABS error. Short circuit between sensorwires IG/IGM is detected 06 Short circuit to ground Yellow
ABS 40B0F ABS error. Cyclic drop out detected at speed higher than 10 km/h. 07 Valve Relay ABS: disabled Yellow
Several wheel revolution necessary. ASR: disabled
SMR: disabled
EBL: disabled
ABS 40B10 ABS error. DC voltage detected. Short circuit or impedance to battery 03 Voltage, low voltage/open circuit EBL: starts depending from Yellow
voltage. deceleration
ABS 40B10 ABS error. Open circuit is detected 05 Brake input open or shorted to ground EBL: starts depending from Yellow
deceleration
ABS 40B12 ABS error. DC voltage detected. Short circuit or impedance to battery 03 Diff. Brake Valve, shorted to UBATT ASR: Diff brake disabled Yellow
voltage.
ABS 40B12 ABS error. Open circuit is detected 05 Diff. Brake Valve, open circuit ASR: Diff brake disabled Yellow
ABS 40B12 ABS error. Short circuit between sensorwires IG/IGM is detected 06 Diff. Brake Valve, shorted to ground ASR: Diff brake disabled Yellow
ABS 40B13 ABS error. DC voltage detected. Short circuit or impedance to battery 03 Trailer Brake Valve, shorted to UBATT Yellow
voltage.
ABS 40B13 ABS error. Open circuit is detected 05 Trailer Brake Valve, open circuit Yellow
ABS 40B13 ABS error. Short circuit between sensorwires IG/IGM is detected 06 Trailer Brake Valve, shorted to ground Yellow
ABS 40B16 ABS error. 08 Yellow
ABS 40B17 ABS error. Open circuit is detected 05 Warning Light WL if grounded. Yellow
Off if bumed out
ABS 40BE7 ABS error.SAEJ1939 Unplausibility between received vehicle speed and ABS 02 SAE J1939 VSC1 speed bad plausibility Supevision normally not activated Yellow
vehicle speed.
ABS 40BE7 ABS error.SAEJ1939 SAE J1939 communication impossible. 05 SAE J1939 open or short circuit ASR: disabled Yellow
SAE J1939 high open or short circuit to plus or ground or sae SMR: disabled
J1939 low or low/high are misured SAE J1939 switched to inactive
because communication is
disturbed.
ABS 40BE7 ABS error.SAEJ1939 SAE J1939 communication impossible. 06 SAE J1939 no access ASR: disabled Yellow
SAE J1939 high open or short circuit to plus or ground or sae SMR: disabled
J1939 low or low/high are misured ABS ECU tries to restart com.
Within 10s it is not possible.
SAE J1939 remains inactive.
FMI 5 might be additionally stored.
ABS 40BE7 ABS error.SAEJ1939 Driveline integrated retarder sends message incorrecly. 07 SAE J1939 ERC_DR time-out Driveline retarder may cause Yellow
Timeout supervision detects faults if activated. instability.
ABS 40BE7 ABS error.SAEJ1939 Engine integrated retarder sends message incorrecly. 08 SAE J1939 ERC_ER (_EXR) time-out Engine retarder may cause Yellow
Timeout supervision detects faults if activated. instability.
Standard is no timeout supervision.
ABS 40BE7 ABS error.SAEJ1939 Gearbox sends message incorrecly. 09 SAE J1939 ETC time-out Dragtorque control influenced. Yellow
Timeout supervision detects faults if activated.
Standard is no timeout supervision.
ABS 40BE7 ABS error.SAEJ1939 Engine control sends torque message incorrectly. 09 SAE J1939 EEC1 time-out Dragtorque control influenced. Yellow
Timeout supervision detects fault.
ABS 40BE7 ABS error.SAEJ1939 Exaust integrated retarder sends message incorrecly. 0A SAE J 1939 ERC_EXR time-out Exaust retarder may cause Yellow
Timeout supervision detects faults if activated. instability.
Standard is no timeout supervision.
ABS 40BE7 ABS error.SAEJ1939 Internal fault 0C SAE J1939, internal error ABS: disabled Yellow
ASR: disabled
SMR: disabled
EBL: disabled
ABS 40BFB ABS error. Overvoltage Supply voltage too high for more than 5s 03 Overvoltage All valve disabled. Yellow
No ABS, SMR, Diff Brake, EBL
ABS 40BFD ABS error. Wheel parameters are out of tolerance. 02 EEPROM, Wheel Parameter incorrect Wrong parameter Yellow
No ABS, ASR, EBL, SM
ABS 40BFD ABS error. Checksum of parameter or analog adjustment is wrong. 0C EEPROM checksum No ABS, SMR, Diff Brake, EBL. Yellow
No blink code.
ABS 40BFE ABS error. No modulators connected. 05 Electronic w/o loads Normal for EOL testing of single Yellow
cabin.
Fault not memorized.
No ABS, SMR, ASR, EBL.
ABS 40BFE ABS error. One axle was much faster than other. 08 excessive slip/dynotester On rolling roads responce Yellow
dynotester slip supervision time can
be exceeded when fault detection is
not disabled by diagnostic tools or
blinkcode (3s).
ABS 40BFE ABS error. Control via modulator was too long. 09 Modulator valve activation time 75% 0f 5min modulator was Yellow
After a delay time function is normal. activated.
No ASR during fault activeness.
ABS 40BFE ABS error. Internal error 0C Multiple possibilities No ABS, SMR, Diff Brake, EBL. Yellow
No blink code.
ADM 40904 internal processor error (Arithmetic) ECU internal fault
ADM 40905 internal processor error (Jumps) ECU internal fault
ADM 40906 internal processor error (Flags) ECU internal fault
ADM 40907 internal processor error (Register) ECU internal fault
ADM 40908 internal processor error (Addressing) ECU internal fault
ADM 40909 internal processor error (Peripheral) ECU internal fault
ADM 4090C defect RAM memory cell ECU internal fault
ADM 4090D false EEPROM checksum during run ECU internal fault
ADM 4090E false EEPROM checksum while ECU internal fault
initialization
ADM 4090F RAM address fault ECU internal fault
ADM 40910 checksum EEPROM 1 false changes in parameter info
ADM 40911 checksum EEPROM 2 false changes in parameter info
ADM 40912 checksum EEPROM 3 false uncontrolled power supply switch off
ADM 40913 checksum EEPROM 4 false uncontrolled power supply switch off
ADM 40914 watchdog 1 works with faults ECU internal fault
ADM 40915 watchdog 2 timeout error ECU internal fault
ADM 40916 watchdog 2 no communication ECU internal fault
ADM 4091C CAN bus Off CAN_Lo, CAN_Hi cross plug, identifier shared,
additional member on CAN bus,
new config. of CAN bus member
ADM 4091D timeout of one ore more CAN Bus CAN bus cable breakage,
devices CAN bus device breakdown,
CAN bus device with false parameters
ADM 40920-23 parameterisation ADM ECU without vehicle configuration

ADM 40928 Power supply battery discharged

Kl.15, Pin 28 low voltage
ADM 40929 Power supply battery discharged,
Pin 29 low voltage relay K1 doesn’t switch,
more errors in the ECU
ADM 4092C Power supply voltage too high, ADM ECU parameterisation for 12V
high voltage on Pin 28
ADM 4092D Power supply voltage too high, ADM ECU parameterisation for 12V
high voltage on Pin 29
ADM 40930 solenoid relay ADM power supply is missing,
relay K1 on Pin 29 doesn’t switch cut in the relay, control circuit,
contact of relay defect,
ADM output stage defect
ADM 40931 solenoid relay ADM
relay K1 on Pin 29 doesn’t switch
ADM 40938 output stage: violation of the fixed ECU internal fault
engagement sequence
ADM 40940 wheel sensor signal wheel sensor signal delivers too high velocity
B10, Pin 47/48, sensor / tone ring damaged
rear axle 2 right
ADM 40941 wheel sensor signal wheel sensor signal delivers too high velocity
B9, Pin 45/46, change of ratio of power train components or tyre equipment?
rear axle 2 left

Bianca Andreana Trakker E4 Errors list Print Date: 21.11.2021

ELTRAC ET-TN-445-87 - Trakker E4 Error Codes Page 5 of 30

ECU SPN F au ltC

omp
one
nt D
es
crip
tio
n F MI F
M I C
omm
en
t L
amps
tat
u s M
ILL
amp
Na
m e [Hex] [
H e
x] D
es
crip
tio
n
ADM 40942 wheel sensor signal wheel sensor signal delivers too high velocity
B7, Pin 43/44, deactivation of speed limiter?
front axle 1 right
ADM 40943 wheel sensor signal wheel sensor signal delivers too high velocity
B6, Pin 14/42, use of vehicle outside of tolerated velocities
front axle 1 left
ADM 40944 wheel sensor signal wheel sensor signal delivers too high velocity
B5, Pin 13/41, hard strokes on rim and driving in difficult areas can produce
rear axle 1 right sporadic oscillation induction and faulty measurements
ADM 40945 wheel sensor signal wheel sensor signal too high
B4, Pin 12/40, sensor / tone ring damaged
rear axle 1 left
ADM 40946 wheel sensor signal wheel sensor signal too high
B39, Pin 11/39, change of ratio of power train components or tyre equipment?
front axle 2 left
ADM 40947 wheel sensor signal wheel sensor signal too high
B40, Pin 25/54, deactivation of speed limiter?
front axle 2 right
ADM 40948 wheel sensor signal air gap sensor / tone wheel too large, signal is missing
B10, Pin 47/48,
rear axle 2 right
ADM 40949 wheel sensor signal air gap sensor / tone wheel too large, signal is missing
B9, Pin 45/46,
rear axle 2 left
ADM 4094A wheel sensor signal air gap sensor / tone wheel too large, signal is missing
B7, Pin 43/44,
front axle 1 right
ADM 4094B wheel sensor signal air gap sensor / tone wheel too large, signal is missing
B6, Pin 14/42,
front axle 1 left
ADM 4094C wheel sensor signal air gap sensor / tone wheel too large, signal is missing
B5, Pin 13/41,
rear axle 1 right
ADM 4094D wheel sensor signal air gap sensor / tone wheel too large, signal is missing
B4, Pin 12/40,
rear axle 1 left
ADM 4094E wheel sensor signal air gap sensor / tone wheel too large, signal is missing
B39, Pin 11/39,
front axle 2 left
ADM 4094F wheel sensor signal air gap sensor / tone wheel too large, signal is missing
B40, Pin 25/54,
front axle 2 right
ADM 40950 wheel sensor signal short circuit to plus or cable breakage
B39, Pin 11/39,
front axle 2 left
ADM 40951 wheel sensor signal sensor: faulty signal
B39, Pin 11/39,
front axle 2 left
ADM 40952 wheel sensor signal sensor resistance too low
B39, Pin 11/39,
front axle 2 left
ADM 40953 wheel sensor signal short circuit to ground
B39, Pin 11/39,
front axle 2 left
ADM 40954 wheel sensor signal short circuit to ground or cable breakage
B4, Pin 12/40,
rear axle 1 left
ADM 40955 wheel sensor signal sensor: faulty signal
B4, Pin 12/40,
rear axle 1 left
ADM 40956 wheel sensor signal sensor resistance too low
B4, Pin 12/40,
rear axle 1 left
ADM 40957 wheel sensor signal short circuit to ground
B4, Pin 12/40,
rear axle 1 left
ADM 40958 wheel sensor signal short circuit to plus or cable breakage
B5, Pin 13/41,
rear axle 1 right
ADM 40959 wheel sensor signal sensor: faulty signal
B5, Pin 13/41,
rear axle 1 right
ADM 4095A wheel sensor signal sensor resistance too low
B5, Pin 13/41,
rear axle 1 right
ADM 4095B wheel sensor signal short circuit to ground
B5, Pin 13/41,
rear axle 1 right
ADM 4095C wheel sensor signal short circuit to plus or cable breakage
B6, Pin 14/42,
front axle 1 left
ADM 4095D wheel sensor signal sensor: faulty signal
B6, Pin 14/42,
front axle 1 left
ADM 4095E wheel sensor signal sensor resistance too low
B6, Pin 14/42,
front axle 1 left
ADM 4095F wheel sensor signal short circuit to ground
B6, Pin 14/42,
front axle 1 left
ADM 40960 wheel sensor signal short circuit to plus or cable breakage
B7, Pin 43/44
front axle 1 right
ADM 40961 wheel sensor signal sensor: faulty signal
B7, Pin 43/44
front axle 1 right
ADM 40962 wheel sensor signal sensor resistance too low
B7, Pin 43/44
front axle 1 right
ADM 40963 wheel sensor signal short circuit to ground
B7, Pin 43/44
front axle 1 right
ADM 40964 wheel sensor signal short circuit to plus or cable breakage
B9, Pin 45/46
rear axle 2 left
ADM 40965 wheel sensor signal sensor: faulty signal
B9, Pin 45/46
rear axle 2 left
ADM 40966 wheel sensor signal sensor resistance too low
B9, Pin 45/46
rear axle 2 left
ADM 40967 wheel sensor signal short circuit to ground
B9, Pin 45/46
rear axle 2 left
ADM 40968 wheel sensor signal short circuit to plus or cable breakage
B10, Pin 47/48
rear axle 2 right
ADM 40969 wheel sensor signal sensor: faulty signal
B10, Pin 47/48
rear axle 2 right
ADM 4096A wheel sensor signal sensor resistance too low
B10, Pin 47/48
rear axle 2 right
ADM 4096B wheel sensor signal short circuit to ground
B10, Pin 47/48
rear axle 2 right
ADM 4096C wheel sensor signal short circuit to plus or cable breakage
B40, Pin 25/54,
front axle 2 right
ADM 4096D wheel sensor signal sensor: faulty signal
B40, Pin 25/54,
front axle 2 right
ADM 4096E wheel sensor signal sensor resistance too low
B40, Pin 25/54,
front axle 2 right
ADM 4096F wheel sensor signal short circuit to ground
B40, Pin 25/54,
front axle 2 right
ADM 40970 tire calibration TC tyre perimeter beyond tolerance
ADM 40971 tire calibration RA1 tyre perimeter beyond tolerance
ADM 40972 tire calibration RA2 tyre perimeter beyond tolerance
ADM 40973 tire calibration FA1 tyre perimeter beyond tolerance
ADM 40974 tire calibration FA2 tyre perimeter beyond tolerance
ADM 40975 tire calibration tyre perimeter beyond tolerance
RA1 - RA2
ADM 40977 tire calibration tyre perimeter beyond tolerance
FA1 - FA2

Bianca Andreana Trakker E4 Errors list Print Date: 21.11.2021

ELTRAC ET-TN-445-87 - Trakker E4 Error Codes Page 6 of 30

ECU SPN Fa ultCom pon en t D

es
crip
tio
n F MI F
M I C
omm
en
t L
amps
tat
u s M
ILL
amp
Na
m e [Hex] [
H e
x] D
es
crip
tio
n
ADM 40978 steering angle sensor B1, (Pin 2, 5, 7) short circuit to plus or voltage too high
ADM 40979 steering angle sensor B1, (Pin 2, 5, 7) steering angle signal different to calculated steering angle
from wheel speed sensors
ADM 40987Asteering angle sensor B1, (Pin 2, 5, 7) signal voltage too low
ADM 4097B steering angle sensor B1, (Pin 2, 5, 7) short circuit to ground
ADM 4097C steering angle sensor B1, (Pin 2, 5, 7) middle position beyond tolerance
ADM 4097D steering angle sensor B1, sensor supply (10V +/- 1V) beyond tolerance
(Pin 2, 5, 7)
ADM 40980 switch S/G, (Pin 36) permanent signal
ADM 40981 switch S/G, (Pin 36) faulty signal
ADM 40982 switch S/G, (Pin 36) voltage too low
ADM 40983 switch S/G, (Pin 36) voltage too high
ADM 409A9 switch S29, Pin 52, status TC or no indication signal after 1s activation to solenoid TC or
interaxle lock RA1-2 interaxle differential lock RA1-2
ADM 409AA switch S29, Pin 52, status TC or signal too long active compared to internal calculation value
interaxle lock RA1-2
ADM 409AD brake pressure switch S25, Pin51, stop signals of brake pressure switch and stop light differ too long
light Pin27
ADM 409AE brake pressure switch S25, Pin51, stop permanent brake signal during driving (>3min at v>10km/h)
light Pin27
ADM 409B0 clutch switch S23, Pin 55, throttle idle clutch signal and gas signal simultaneous active more than
switch S31, Pin 24 1min.
ADM 409B1 clutch switchS23, Pin 55 clutch signal active more than 3min. at v>10km/h
ADM 409B3 clutch switchS23, Pin 55 no change of signal while acceleration from 5km/h to 40km/h
(check with manual transmissions only!)
ADM 409B9 air pressure switch S20, Pin 53 low air pressure and vehicle speed >0 km/h
ADM 409BD throttle idle switch S31, Pin 24 on 10x of braking the gas pedal each time was pressed
ADM 409C8 solenoid valve Y10, Y110, Pin 35 interruption
ADM 409CA solenoid valve Y10, Y110, Pin 35 short circuit to ground
ADM 409CB solenoid valve Y10, Y110, Pin 35 short circuit to plus
ADM 409CC solenoid valve Y11, Y111, Pin 33 interruption
ADM 409CE solenoid valve Y11, Y111, Pin 33 short circuit to ground
ADM 409CF solenoid valve Y11, Y111, Pin 33 short circuit to plus
ADM 409D0 solenoid valve Y12,Y112, Pin 34 interruption
ADM 409D2 solenoid valve Y12,Y112, Pin 34 short circuit to ground
ADM 409D3 solenoid valve Y12,Y112, Pin 34 short circuit to plus
ADM 409D4 solenoid valve Y13, Y113, Pin 32 interruption
ADM 409D6 solenoid valve Y13, Y113, Pin 32 short circuit to ground
ADM 409D7 solenoid valve Y13, Y113, Pin 32 short circuit to plus
ADM 409D8 solenoid valve Y14, Y114, Pin 3 interruption
ADM 409DA solenoid valve Y14, Y114, Pin 3 short circuit to ground
ADM 409DB solenoid valve Y14, Y114, Pin 3 short circuit to plus
ADM 409DC solenoid valve Y15, Y115, Pin 31 interruption
ADM 409DE solenoid valve Y15, Y115, Pin 31 short circuit to ground
ADM 409DF solenoid valve Y15, Y115, Pin 31 short circuit to plus
ADM 409E0 solenoid valve Y16, Y116, Pin 4 interruption
ADM 409E2 solenoid valve Y16, Y116, Pin 4 short circuit to ground
ADM 409E3 solenoid valve Y16, Y116, Pin 4 short circuit to plus
ADM 409F0 message EEC1, CAN bus member with source address 0x00
cycle time - time out elapsed time >= 3x defined interval
ADM 409F1 message ETC1, ETC2 CAN bus member with source address 0x03
cycle time - time out elapsed time >= 3x defined interval
ADM 409F2 message EBC1, PROP_AM, HRW CAN bus member with source address 0x0B
cycle time - time out elapsed time >= 3x defined interval
ADM 409F3 message ERC1_DR CAN bus member with source address 0x10
cycle time - time out elapsed time >= 3x defined interval
ADM 409F5 message BORDELECTRONIC & CAN bus member with source address 0x31
PROP_VM elapsed time >= 3x defined interval
cycle time - time out
ADM 409F8 NMI occurred micro processor
ADM 409F9 stack overflow occurred micro processor
ADM 409FA stack underflow occurred micro processor
ADM 409FB illegal bus access occurred micro processor
ADM 409FC illegal instruction access occurred micro processor
ADM 409FD illegal operand access occurred micro processor
ADM 409FE protected instruction fault occurred micro processor
ADM 409FF undefined operation code occurred micro processor
AHTa 44502 HS button 1F Condition exists Button jammed Yellow
AHTa 44503 CAN communication 1F Condition exists CAN communication error Yellow
AHTa 44504 Air signal 06 Current above normal or grounded Air signal short to battery or short Yellow
circuit circuit
AHTa 44505 Anti-theft alarm system 06 Current above normal or grounded "Heater status" signal short circuit Yellow
circuit or transistor fault
AHTa 44509 TRS 1F Condition exists TRS shutoff Yellow
AHTa 4450A Voltage shutoff 03 Voltage above normal, or shorted to Over voltage Yellow
high source
AHTa 4450B Voltage shutoff 04 Voltage below normal, or shorted to low Under voltage Yellow
source
AHTa 4450C Overheat 1F Condition exists Overheat detected software level Yellow
AHTa 4450D Flame sensor 1F Condition exists Flame sensor out of tolerance or Yellow
overheat at flame sensor (system
locked)
AHTa 4450E Overheat 1F Condition exists Redundant overheat monitoring Yellow
(system locked)
AHTa 4450F Overheat 1F Condition exists Overhaet counter overrun (system Yellow
locked)
AHTa 44511 Overheat 1F Condition exists Overhaet detected hardware level Yellow
(system locked)
AHTa 44513 Low ignition power 1F Condition exists Yellow
AHTa 44514 Glowplug 05 Current below nominal or open circuit Glowplug interrupted Yellow
AHTa 44515 Glowplug 06 Current above normal or grounded Glowplug overload or short circuit Yellow
circuit
AHTa 44516 Glowplug 03 Voltage above normal, or shorted to Glowplug short to battery or Yellow
high source transistor failure
AHTa 44519 K-line 06 Current above normal or grounded K-line short circuit Yellow
circuit
AHTa 4451B OEM K-line 1F Condition exists OEM K-line error Yellow
AHTa 4451E Blower fan 1F Condition exists Blower fan out of range Yellow
(electromotive force not present)
AHTa 4451F Blower fan 05 Current below nominal or open circuit Blower fan interrupted Yellow
AHTa 44520 Blower fan 06 Current above normal or grounded Blower fan short circuit or overload Yellow
circuit
AHTa 44521 Blower fan 1F Condition exists Blower fan does not turn Yellow
AHTa 44522 Blower fan 03 Voltage above normal, or shorted to Blower fan short to battery or Yellow
high source transistor failure
AHTa 4452F Fuel pump 06 Current above normal or grounded Fuel pump short circuit or overload Yellow
circuit
AHTa 44530 Fuel pump 05 Current below nominal or open circuit Fuel pump intrrupted Yellow
AHTa 44531 Fuel pump 03 Voltage above normal, or shorted to Fuel pump short to battery or Yellow
high source transistor failure
AHTa 44532 Start counter overrun (system locked) 1F Condition exists Yellow
AHTa 44533 Cooling time exceeded 1F Condition exists Yellow
AHTa 44534 Safety time exceeded 1F Condition exists Yellow
AHTa 44535 Flame off in power stage "POWER" 1F Condition exists Yellow
AHTa 44536 Flame off in power stage "HIGH" 1F Condition exists Yellow
AHTa 44537 Flame off in power stage "MEDIUM" 1F Condition exists Yellow
AHTa 44538 Flame off in power stage "SMALL" 1F Condition exists Yellow
AHTa 4453C Temperature control sensor 05 Current below nominal or open circuit Temperature control sensor Yellow
interrupted
AHTa 4453D Temperature control sensor 06 Current above normal or grounded Temperature control sensor short Yellow
circuit circuit
AHTa 4453E Rated value 05 Current below nominal or open circuit Rated value interrupted Yellow
AHTa 4453F Rated value 06 Current above normal or grounded Rated value short circuit Yellow
circuit
AHTa 44540 Flame sensor 05 Current below nominal or open circuit Flame sensor interrupted Yellow
AHTa 44541 Flame sensor 06 Current above normal or grounded Flame sensor short circuit Yellow
circuit
AHTa 44547 Overheat sensor 05 Current below nominal or open circuit Overheat sensor interrupted Yellow
AHTa 44548 Overheat sensor 06 Current above normal or grounded Overheat sensor short circuit Yellow
circuit
AHTa 4454A System locked, overheat detection 1F Condition exists Yellow
hardware fault
AHTa 4455A ECU reset internal 1F Condition exists Yellow
AHTa 4455C RAM/ROM error 1F Condition exists Yellow
AHTa 4455E EEPROM fault 1F Condition exists Yellow
AHTa 44560 Internal temperature sensor 1F Condition exists Internal temperature sensor fault Yellow
AHTa 44561 Internal ECU Fault 1F Condition exists Yellow
AHTw 44403 CAN 1F Condition exists CAN message timeout, refer to Yellow
specs
AHTw 44405 Heater status 06 Current below normal or open circuit Io>200mA Yellow
AHTw 44409 Can Signal: PTO Status, BC_Status1 1F Condition exists ADR condition true Yellow
AHTw 4440A K30 03 Voltage above normal, or shorted to Vb > 30V for 6 sec. Yellow
high source
AHTw 4440B K30 04 Voltage below normal, or shorted to low Vb < 20V for 20 sec. Yellow
source
AHTw 4440C Overheat sensor 1F Condition exists T1 > 115°C Yellow

Bianca Andreana Trakker E4 Errors list Print Date: 21.11.2021

ELTRAC ET-TN-445-87 - Trakker E4 Error Codes Page 7 of 30

ECU SPN F
aultC
omp
one
nt D
es
crip
tio
n F MI FM I C
omm
en
t L
amps
tat
u s M
ILL
amp
Name [Hex] [
H e
x] D escr
ip tion
AHTw 44414 Glowplug 05 Current below normal or open circuit Io<500uA (off) Yellow
<0,9A (on)
AHTw 44415 Glowplug 06 Current above normal or grounded Io > 35A Yellow
circuit
AHTw 44420 Combustion Fan 06 Current above normal or grounded Io > 50A Yellow
circuit
AHTw 44421 Feedback signal of combustion fan = n1 1F Condition exists Combustion fan doesn't turn: Yellow
n = requested revs (n/2) > n1 > (n + n/2)
AHTw 44425 Water pump 1F Condition exists Water pump doesn't turn: Yellow
Uemk < Threshold
AHTw 44427 Cab fan Signal 06 Current above normal or grounded Io >0,5A Yellow
circuit
AHTw 4442A Water pump 06 Current above normal or grounded Io >35A Yellow
circuit
AHTw 4442F Fuel pump 06 Current above normal or grounded Io >35A Yellow
circuit
AHTw 44430 Fuel pump 05 Current below normal or open circuit Yellow
Io<1mA (off); io<0,9A (on)
AHTw 44433 Flame Sensor 1F Condition exists Flame present during start: T >75°C Yellow
AHTw 44434 Flame Sensor 1F Condition exists Safety time exceeded: Yellow
tstart > 310 sec.
AHTw 44435 Flame Sensor 1F Condition exists Flame off in power stage power: Yellow
T < 140°C
AHTw 44436 Flame Sensor 1F Condition exists Flame off in power stage big: Yellow
T < 120°C
AHTw 44437 Flame Sensor 1F Condition exists Flame off in power stage medium: Yellow
T < 104°C
AHTw 44438 Flame Sensor 1F Condition exists Flame off in power stage small: Yellow
T < 90°C
AHTw 4443C Water Temperature 05 Current below normal or open circuit Yellow
Ri > 2400 Ohm +/- 150 Ohm
AHTw 4443D Water Temperature 06 Current above normal or grounded Yellow
circuit Ri < 400 Ohm +/- 50 Ohm
AHTw 44440 Flame sensor 05 Current below normal or open circuit Yellow
Ri > 2900 +/- 100 Ohm
AHTw 44441 Flame sensor 06 Current above normal or grounded Yellow
circuit Ri < 650 +/- 100 Ohm
AHTw 44447 Overheat sensor 05 Current below normal or open circuit Ri>(2000k ± 500kΩ) (tw<-25°C); Ri Yellow
> (200k ± 35kΩ) (tw>= -25°C);
AHTw 44448 Overheat sensor 06 Current above normal or grounded Ri < 70Ohm +/- 50Ohm Yellow
circuit
AHTw 4445A - 1F Condition exists Watch dog time out Yellow
AHTw 4445B - 1F Condition exists Electrical disturbance refer to the Yellow
specification
AHTw 4445C - 1F Condition exists ROM Error: Checksum is wrong Yellow
AHTw 4445D - 1F Condition exists RAM Error: Memory error Yellow
AHTw 4445E - 1F Condition exists EEPROM: Checksum is wrong Yellow
AHTw 4445F - 1F Condition exists Faulty internal relais: Relais cannot Yellow
be switched off
AHTw 44461 - 1F Condition exists Plausibility error: Unlogic program Yellow
conditions
Allison 7D3 General Transmission Fault 1F Not available Yellow
Allison 78 Retarder Oil Temperature 0F Data valid but above normal operation Yellow
range – Least Severe Level
Allison B1 Transmission Oil Temperature 0F Data valid but above normal operation Yellow
range – Least Severe Level
CDM 4ED07 Window button status 02 Data erratic, intermittent or incorrect Up and down action occurs as the Yellow
same time
CDM 4ED0B Illumination control (BSP450) 06 Current above normal or grounded Illumination on when input off Yellow
circuit
CDM 4ED0C Power Window 0B Root cause not known Relay contact stuck Yellow
CDM 4ED0D Door Lock 0B Root cause not known Relay contact stuck Yellow
CDM 4ED0E Mirror Heating 0B Root cause not known Relay contact stuck Yellow
CDM 4ED12 BCB Message 02 Data erratic, intermittent or incorrect BC_Status message missing on Yellow
BCB
CDM 4ED13 BCB Message 02 Data erratic, intermittent or incorrect Opposite Door Module status Yellow
missing on BCB
CLC 41905 Solar sensor 04 Voltage below normal or shorted lo low Yellow
surce
CLC 41909 Bed Room temp. Sensor 04 Voltage below normal or shorted lo low Yellow
surce
CLC 41908 Heater exchanger temp. sensor 04 Voltage below normal or shorted lo low Yellow
surce
CLC 41908 Heater exchanger temp. sensor 05 Current below normal or open circuit Yellow
CLC 41907 Evaporator temp. sensor 04 Voltage below normal or shorted lo low Yellow
surce
CLC 41907 Evaporator temp. sensor 05 Current below normal or open circuit Yellow
CLC 41906 Indoor temp. sensor 04 Voltage below normal or shorted lo low Yellow
surce
CLC 41906 Indoor temp. sensor 05 Current below normal or open circuit Yellow
CLC 41901 Feedback signal floor flap 04 Voltage below normal or shorted lo low Yellow
surce
CLC 41901 Feedback signal floor flap 05 Current below normal or open circuit Yellow
CLC 41902 Feedback signal defrost flap 04 Voltage below normal or shorted lo low Yellow
surce
CLC 41902 Feedback signal defrost flap 05 Current below normal or open circuit Yellow
CLC 41904 Feedback signal recirculation flap 04 Voltage below normal or shorted lo low Yellow
surce
CLC 41904 Feedback signal recirculation flap 05 Current below normal or open circuit Yellow
CLC 41914 Sensor Fan Diagnosis 07 Mechanical system not responding or Yellow
out of adjustment
CLC 41903 Feedback signal bilevel flap 04 Voltage below normal or shorted lo low Yellow
surce
CLC 41903 Feedback signal bilevel flap 05 Current below normal or open circuit Yellow
CLC 4190E Heating valve 05 Current below normal or open circuit Yellow
CLC 4190E Heating valve 03 Voltage above normal or shorted to high Yellow
source
CLC 41910 Floor flap motor 04 Voltage below normal or shorted lo low Yellow
surce
CLC 41910 Floor flap motor 03 Voltage above normal or shorted to high Yellow
source
CLC 41910 Floor flap motor 07 Mechanical system not responding or Yellow
out of adjustment
CLC 41911 Defrost flap motor 04 Voltage below normal or shorted lo low Yellow
surce
CLC 41911 Defrost flap motor 03 Voltage above normal or shorted to high Yellow
source
CLC 41911 Defrost flap motor 07 Mechanical system not responding or Yellow
out of adjustment
CLC 41913 Recirculation flap motor 04 Voltage below normal or shorted lo low Yellow
surce
CLC 41913 Recirculation flap motor 03 Voltage above normal or shorted to high Yellow
source
CLC 41913 Recirculation flap motor 07 Mechanical system not responding or Yellow
out of adjustment
CLC 41912 Bilevel flap motor 04 Voltage below normal or shorted lo low Yellow
surce
CLC 41912 Bilevel flap motor 03 Voltage above normal or shorted to high Yellow
source
CLC 41912 Bilevel flap motor 07 Mechanical system not responding or Yellow
out of adjustment
CLC 4190D Compressor clutch relais 04 Voltage below normal or shorted lo low Yellow
surce
CLC 4190F Sensor fan 04 Voltage below normal or shorted lo low Yellow
surce
CLC 41915 Blower control voltage 04 Voltage below normal or shorted lo low Yellow
surce
CLC 41915 Blower control voltage 03 Voltage above normal or shorted to high Yellow
source
CLC 41916 BCB data link 13 Received network data in error Yellow
CLC 41917 BCB data link 02 Data erratic, intermittent or incorrect Yellow
DDM 4EC03 Heater button status 02 Data erratic, intermittent or incorrect Button Stuck > 30 sec Yellow
DDM 4EC05 Mirror joystick status 02 Data erratic, intermittent or incorrect Invalid Joystick State Yellow
DDM 4EC06 Mirror button selection status 02 Data erratic, intermittent or incorrect Button Stuck > 30 sec Yellow
DDM 4EC07 Window button status 02 Data erratic, intermittent or incorrect Up and down action occurs at the Yellow
same time
DDM 4EC0B Illumination control 06 Current above normal or grounded Illumination on when input off Yellow
circuit
DDM 4EC0C Power Window 0B Root cause not known Relay contact stuck Yellow
DDM 4EC0D Door Lock 0B Root cause not known Relay contact stuck Yellow
DDM 4EC0E Mirror Heating 0B Root cause not known Relay contact stuck Yellow
DDM 4EC12 BCB Message 02 Data erratic, intermittent or incorrect BC_Status message missing on Yellow
BCB
DDM 4EC13 BCB Message 02 Data erratic, intermittent or incorrect Opposite Door Module status Yellow
message missing on BCB

Bianca Andreana Trakker E4 Errors list Print Date: 21.11.2021

ELTRAC ET-TN-445-87 - Trakker E4 Error Codes Page 8 of 30

ECU S P
N F aultCo mp
one
nt D
es
crip
tio
n F MI F
M I C
omm
en
t L
amps
tat
u s M
ILL
amp
Name [
H ex] [
H e
x] D
es
crip
tio
n
DTCO 36 Handling information Printout not possible Printout are currently not possible. SPN
Any printout in progress will be visualized on
cancelled and print requested will DTCO, on IC
be rejected. only specific
Tell Tale or
Icon
DTCO 37 Handling information Printout delayed A printout will be delayed or
cancelled
DTCO 38 Handling information Drawer open In one of the following situation it is
determined that the printer drawer is
open:
- withdrawing a tachograph card
- requesting a printout
- during a printout
DTCO 39 Handling information no paper It is determined during a printout or
during a print request that there is
no paper in the printer. A printout in
progress will be interrupted or any
print request will be rejected.
DTCO 34 Handling information ejection not possible A tachograph card cannot be
ejected; the request is rejected.
DTCO 49 Handling information recording inconsistent While reading-in a tachograph card
(in card slot 1), an inconsistency is
found in the links within the date
data.
DTCO 50 Handling information card error The inserted card (in card slot 1)
cannot be read or written to.
DTCO 51 Handling information wrong card type The inserted card (in card slot 1) is
not a tachograph card.
DTCO 52 Handling information card locked The inserted workshop card is
locked
DTCO 33 Handling information v-impulses w/o ignition Motion sensor impulse when
ignition is switched off
DTCO 53 Handling information internal fault Process not possible, tachograph
card is not accepted and is ejected
DTCO 57 Handling information After an interrupted driving time of 4
hours 15 minutes, the DTCO 1381
warns of the need for a required
break.
DTCO 56 Handling information After an interrupted driving time of 4
hours 30 minutes, the DTCO 1381
warns of the need for a required
break.
DTCO 02 System Event internal fault A generally serious fault has
03 appeared in the device or a
communication fault with the
attached test device has appeared
during calibration
DTCO 04 System Event internal fault A generally serious fault has
appeared in the device.
DTCO 05 System Event internal fault A communication fault with the
attached test device has appeared
during calibration.
DTCO 08 System Event internal fault Fault on the keyboard
DTCO 10 System Event internal fault Fault at v-impulse output (B7)
DTCO 13 System Event internal fault Other CAN fault, message of the
can controller, such as no
participant, no acknowledgement,
etc.
DTCO 14 System Event internal fault CAN fault, message of the CAN
controller status " Bus off"
DTCO 15 System Event internal fault Fault or interruption in the
communication with an external
display instrument
DTCO 40 System Event internal fault Fault in card mechanics
DTCO 06 System Event time fault The time in the DTCO 1381 is not
correct
DTCO 09 System Event time fault Fault in calibration memory
DTCO 11 System Event internal fault Printer fault
DTCO 07 System Event display fault Display fault (sometimes no display)
DTCO 12 System Event download fault A communication error has
appeared while downloading card or
memory data
DTCO 16 System Event sensor fault Internal sensor fault; the KITAS
2171 motion sensor announces an
internal fault after a self-test
DTCO 41 System Event card fault Communication fault with inserted
tachograph cards (in card slot1). A
communication fault has appeared
during reading or writing of card
data
DTCO 17 System Event security breach Data security fault. Internal sensor,
the motion sensor indicates an error
in the data integrity.
DTCO 18 System Event security breach Internal sensor error, authentication
error. The motion sensor indicates
an error during authentication.
DTCO 23 System Event security breach Error during authentication of the
motion sensor. The DTCO 1381
indicates an error during
authentication of the motion sensor
DTCO 24 System Event security breach Error during comparison of the
serial number of the motion sensor
DTCO 25 System Event security breach Error in data memory. Due to an
error in the data memory of the
DTCO 1381, data security is no
longer ensured
DTCO 26 System Event security breach The DTCO 1381 housing was
opened
DTCO 27 System Event security breach Invalid signals on the calibration
interface. The interface is blocked
and additional signals will be
ignored until the entry of a PIN
number is requested (workshop
cars is invalid)
DTCO 43 System Event security breach Card missing; the DTCO 1381 no
longer detects an inserted card (in
card slot 1)
DTCO 42 System Event security breach Security breach during
47 authentication of a tachograph card
or authenticity of the data is not
ensured
DTCO 31 System performance power interruption The operational voltage of the
DTCO is outside of the specification
DTCO 19 System performance power interruption The motion sensor's voltage supply
was or is interrupted
DTCO 21 System performance sensor fault Error during sensor communication
DTCO 22 System performance sensor fault Error during sensor communication
DTCO 20 System performance sensor fault Error during sensor communication
DTCO 28 System performance driving without card Driving without a card or without a
valid driver card or workshop card
slot 1.
DTCO 46 System performance insertion while driving A tachograph card was inserted
after driving had commenced
DTCO 45 System performance time overlap Negative difference relative to last
vehicle (EC recording equipment)
DTCO 48 System performance card not valid The inserted tachograph card (in
card slot 1) has expired or is invalid
DTCO 29 System performance card conflict Invalid card combination in card
slots 1 and 2; these two tachograph
cards may be inserted at the same
time.
DTCO 44 System performance card not closed When a driver or workshop card (in
card slot 1) is read it is determined
that the card as not properly
withdrawn in the least vehicle or the
data was not saved properly.
DTCO 30 System performance over speed The programmed maximum speed
was exceeded for longer than 60
seconds
ECAS 42FFE Control Unit (internal fault) 02 Data erratic, intermittent or incorrect Yellow
ECAS 42FFE Control Unit (internal fault) 0B Failure mode not identifiable Yellow
ECAS 42FFE Control Unit (internal fault) 0C Bad intelligent device or component Yellow
ECAS 42F26 Checksum ECU specific data 02 Data erratic, intermittent or incorrect Yellow
ECAS 42F27 Checksum parameter data 02 Data erratic, intermittent or incorrect Yellow
ECAS 42F27 Checksum parameter data 0D Out of calibration Yellow

Bianca Andreana Trakker E4 Errors list Print Date: 21.11.2021

ELTRAC ET-TN-445-87 - Trakker E4 Error Codes Page 9 of 30

ECU SPN FaultC om pon e nt D

es
crip
tio
n F MI F M I C
omm
en
t L
amps
tat
u s M
ILL
amp
Name [Hex] [
H e
x] D escr iption
ECAS 42F28 Checksum calibration data distnce 02 Data erratic, intermittent or incorrect Yellow
sensor
ECAS 42F28 Checksum calibration data level sensor 0D Out of calibration Yellow
ECAS 42F29 Checksum calibration data pressure 02 Data erratic, intermittent or incorrect Yellow
sensor
ECAS 42F2A Checksum max. Axle load data 02 Data erratic, intermittent or incorrect Yellow
ECAS 42F2A Checksum max. Axle load data 0C Bad intelligent device or component Yellow
ECAS 42F2A Checksum max. Axle load data 0D Bad intelligent device or component Yellow
ECAS 42F5C Checksum configuration CAN data 02 Data erratic, intermittent or incorrect Yellow
ECAS 42F62 Parameter check / component check 02 Data erratic, intermittent or incorrect Yellow
ECAS 42F62 Parameter check / component check 0B Failure mode not identifiable Yellow
ECAS 42F22 Common supply for solenoid valves 03 Voltage above or shorted high Yellow
ECAS 42F22 Common supply for solenoid valves 05 Current below nominal or open circuit Yellow
ECAS 42F22 Common supply for solenoid valves 06 Current above nominal or grounded Yellow
circuit
ECAS 42F22 Common supply for solenoid valves 0B Failure mode not identifiable Yellow
ECAS 42F01 2/2 solenoid valve front axle right 03 Voltage above or shorted high Yellow
ECAS 42F01 2/2 solenoid valve front axle right 05 Current below nominal or open circuit Yellow
ECAS 42F01 2/2 solenoid valve front axle right 06 Current above nominal or grounded Yellow
circuit
ECAS 42F02 2/2 solenoid valve front axle right 03 Voltage above or shorted high Yellow
ECAS 42F02 2/2 solenoid valve front axle right 05 Current below nominal or open circuit Yellow
ECAS 42F02 2/2 solenoid valve front axle right 06 Current above nominal or grounded Yellow
circuit
ECAS 42F03 2/2 solenoid valve drive axle right 03 Voltage above or shorted high Yellow
ECAS 42F03 2/2 solenoid valve drive axle right 05 Current below nominal or open circuit Yellow
ECAS 42F03 2/2 solenoid valve drive axle right 06 Current above nominal or grounded Yellow
circuit
ECAS 42F04 2/2 solenoid valve drive axle left 03 Voltage above or shorted high Yellow
ECAS 42F04 2/2 solenoid valve drive axle left 05 Current below nominal or open circuit Yellow
ECAS 42F04 2/2 solenoid valve drive axle left 06 Current above nominal or grounded Yellow
circuit
ECAS 42F05 2/2 solenoid valve 3° axle right 03 Voltage above or shorted high Yellow
ECAS 42F05 2/2 solenoid valve 3° axle right 05 Current below nominal or open circuit Yellow
ECAS 42F05 2/2 solenoid valve 3° axle right 06 Current above nominal or grounded Yellow
circuit
ECAS 42F06 2/2 solenoid valve 3° axle left 03 Voltage above or shorted high Yellow
ECAS 42F06 2/2 solenoid valve 3° axle left 05 Current below nominal or open circuit Yellow
ECAS 42F06 2/2 solenoid valve 3° axle left 06 Current above nominal or grounded Yellow
circuit
ECAS 42F07 Central 3/2 solenoid valve drive axle 03 Voltage above or shorted high Yellow
ECAS 42F07 Central 3/2 solenoid valve drive axle 05 Current below nominal or open circuit Yellow
ECAS 42F07 Central 3/2 solenoid valve drive axle 06 Current above nominal or grounded Yellow
circuit
ECAS 42F08 3/3 solenoid valve 3° axle lifting 03 Voltage above or shorted high Yellow
ECAS 42F08 3/3 solenoid valve 3° axle lifting 05 Current below nominal or open circuit Yellow
ECAS 42F08 3/3 solenoid valve 3° axle lifting 06 Current above nominal or grounded Yellow
circuit
ECAS 42F09 3/3 solenoid valve 3° axle lowering 03 Voltage above or shorted high Yellow
ECAS 42F09 3/3 solenoid valve 3° axle lowering 05 Current below nominal or open circuit Yellow
ECAS 42F09 3/3 solenoid valve 3° axle lowering 06 Current above nominal or grounded Yellow
circuit
ECAS 42F0A 2/2 solenoid valve 3° axle lift belows 03 Voltage above or shorted high Yellow
ECAS 42F0A 2/2 solenoid valve 3° axle lift belows 05 Current below nominal or open circuit Yellow
ECAS 42F0A 2/2 solenoid valve 3° axle lift belows 06 Current above nominal or grounded Yellow
circuit
ECAS 42F0D Solenoid valve Mainflow throtte 03 Voltage above or shorted high Yellow
ECAS 42F0D Solenoid valve Mainflow throtte 05 Current below nominal or open circuit Yellow
ECAS 42F0D Solenoid valve Mainflow throtte 06 Current above nominal or grounded Yellow
circuit
ECAS 42F0E Solenoid valve Lateral throtte 03 Voltage above or shorted high Yellow
ECAS 42F0E Solenoid valve Lateral throtte 05 Current below nominal or open circuit Yellow
ECAS 42F0E Solenoid valve Lateral throtte 06 Current above nominal or grounded Yellow
circuit
ECAS 42F2B Central 3/2 solenoid valve 3° axle 03 Voltage above or shorted high Yellow
ECAS 42F2B Central 3/2 solenoid valve 3° axle 05 Current below nominal or open circuit Yellow
ECAS 42F2B Central 3/2 solenoid valve 3° axle 06 Current above nominal or grounded Yellow
circuit
ECAS 42F2C Central 3/2 solenoid valve front axle 03 Voltage above or shorted high Yellow
ECAS 42F2C Central 3/2 solenoid valve front axle 05 Current below nominal or open circuit Yellow
ECAS 42F2C Central 3/2 solenoid valve front axle 06 Current above nominal or grounded Yellow
circuit
ECAS 42F10 Distance sensor front axle right 03 Voltage above or shorted high Yellow
ECAS 42F10 Distance sensor front axle right 05 Current below nominal or open circuit Yellow
ECAS 42F10 Distance sensor front axle right 06 Current above nominal or grounded Yellow
circuit
ECAS 42F10 Distance sensor front axle right 02 Data erratic, intermittent or incorrect Yellow
ECAS 42F11 Level sensor front axle left 03 Voltage above or shorted high Yellow
ECAS 42F11 Level sensor front axle left 05 Current below nominal or open circuit Yellow
ECAS 42F11 Level sensor front axle left 06 Current above nominal or grounded Yellow
circuit
ECAS 42F11 Level sensor front axle left 02 Data erratic, intermittent or incorrect Yellow
ECAS 42F12 Distance sensor drive axle right 03 Voltage above or shorted high Yellow
ECAS 42F12 Distance sensor drive axle right 05 Current below nominal or open circuit Yellow
ECAS 42F12 Distance sensor drive axle right 06 Current above nominal or grounded Yellow
circuit
ECAS 42F12 Distance sensor drive axle right 02 Data erratic, intermittent or incorrect Yellow
ECAS 42F13 Distance sensor drive axle left 03 Voltage above or shorted high Yellow
ECAS 42F13 Distance sensor drive axle left 05 Current below nominal or open circuit Yellow
ECAS 42F13 Distance sensor drive axle left 06 Current above nominal or grounded Yellow
circuit
ECAS 42F13 Distance sensor drive axle left 02 Data erratic, intermittent or incorrect Yellow
ECAS 42F16 Pressure sensor front axle right 03 Voltage above or shorted high Yellow
ECAS 42F16 Pressure sensor front axle right 05 Current below nominal or open circuit Yellow
ECAS 42F16 Pressure sensor front axle right 06 Current above nominal or grounded Yellow
circuit
ECAS 42F17 Pressure sensor front axle left 03 Voltage above or shorted high Yellow
ECAS 42F17 Pressure sensor front axle left 05 Current below nominal or open circuit Yellow
ECAS 42F17 Pressure sensor front axle left 06 Current above nominal or grounded Yellow
circuit
ECAS 42F18 Pressure sensor drive axle right 03 Voltage above or shorted high Yellow
ECAS 42F18 Pressure sensor drive axle right 05 Current below nominal or open circuit Yellow
ECAS 42F18 Pressure sensor drive axle right 06 Current above nominal or grounded Yellow
circuit
ECAS 42F19 Pressure sensor drive axle left 03 Voltage above or shorted high Yellow
ECAS 42F19 Pressure sensor drive axle left 05 Current below nominal or open circuit Yellow
ECAS 42F19 Pressure sensor drive axle left 06 Current above nominal or grounded Yellow
circuit
ECAS 42F1A Pressure sensor 3° axle right 03 Voltage above or shorted high Yellow
ECAS 42F1A Pressure sensor 3° axle right 05 Current below nominal or open circuit Yellow
ECAS 42F1A Pressure sensor 3° axle right 06 Current above nominal or grounded Yellow
circuit
ECAS 42F1B Pressure sensor 3° axle left 03 Voltage above or shorted high Yellow
ECAS 42F1B Pressure sensor 3° axle left 05 Current below nominal or open circuit Yellow
ECAS 42F1B Pressure sensor 3° axle left 06 Current above nominal or grounded Yellow
circuit
ECAS 42F1C Pressure sensor lift belows 03 Voltage above or shorted high Yellow
ECAS 42F1C Pressure sensor lift belows 05 Current below nominal or open circuit Yellow
ECAS 42F1C Pressure sensor lift belows 06 Current above nominal or grounded Yellow
circuit
ECAS 42F2D Pressure sensor brake pressure 03 Voltage above or shorted high Yellow
ECAS 42F2D Pressure sensor brake pressure 05 Current below nominal or open circuit Yellow
ECAS 42F2D Pressure sensor brake pressure 06 Current above nominal or grounded Yellow
circuit
ECAS 42F2E Power supply for pressure sensor 03 Voltage above or shorted high Yellow
ECAS 42F2E Power supply for pressure sensor 06 Current above nominal or grounded Yellow
circuit
ECAS 42F1D Secutiry device (side walk detector 03 Voltage above or shorted high Yellow
sensor)
ECAS 42F1D Secutiry device (side walk detector 05 Current below nominal or open circuit Yellow
sensor)
ECAS 42F1D Secutiry device (side walk detector 06 Current above nominal or grounded Yellow
sensor) circuit
ECAS 42F2F Power supply for ECAS remote controls 03 Voltage above or shorted high Yellow
ECAS 42F2F Power supply for ECAS remote controls 06 Current above nominal or grounded Yellow
circuit
ECAS 42F30 Remote control 1 data line 03 Voltage above or shorted high Yellow
ECAS 42F30 Remote control 1 data line 06 Current above nominal or grounded Yellow
circuit
ECAS 42F31 Remote control 1 clock line 03 Voltage above or shorted high Yellow
ECAS 42F31 Remote control 1 clock line 06 Current above nominal or grounded Yellow
circuit
ECAS 42F21 Remote control 1 0B Failure mode not identificable Yellow
ECAS 42F32 Remote control 2 data line 03 Voltage above or shorted high Yellow
ECAS 42F32 Remote control 2 data line 06 Current above nominal or grounded Yellow
circuit
ECAS 42F33 Remote control 2 clock line 03 Voltage above or shorted high Yellow

Bianca Andreana Trakker E4 Errors list Print Date: 21.11.2021

ELTRAC ET-TN-445-87 - Trakker E4 Error Codes Page 10 of 30

ECU SPN F au ltC o mp o ne n

t D
es
crip
tio
n F MI FM I C
omm
en
t L
amps
tat
u s M
ILL
amp
Name [Hex] [
H e
x] De s criptio n
ECAS 42F33 Remote control 2 clock line 06 Current above nominal or grounded Yellow
circuit
ECAS 42F34 Remote control 2 00 Failure mode not identificable Yellow
ECAS 42F35 Common supply for ESAC solenoid 03 Voltage above or shorted high Yellow
valves
ECAS 42F35 Common supply for ESAC solenoid 05 Current below nominal or open circuit Yellow
valves
ECAS 42F35 Common supply for ESAC solenoid 06 Current above nominal or grounded Yellow
valves circuit
ECAS 42F36 Prop. Valve front axle left 03 Voltage above or shorted high Yellow
ECAS 42F36 Prop. Valve front axle left 05 Current below nominal or open circuit Yellow
ECAS 42F36 Prop. Valve front axle left 06 Current above nominal or grounded Yellow
circuit
ECAS 42F37 Prop. Valve front axle right 03 Voltage above or shorted high Yellow
ECAS 42F37 Prop. Valve front axle right 05 Current below nominal or open circuit Yellow
ECAS 42F37 Prop. Valve front axle right 06 Current above nominal or grounded Yellow
circuit
ECAS 42F38 Prop. Valve drive axle left 03 Voltage above or shorted high Yellow
ECAS 42F38 Prop. Valve drive axle left 05 Current below nominal or open circuit Yellow
ECAS 42F38 Prop. Valve drive axle left 06 Current above nominal or grounded Yellow
circuit
ECAS 42F39 Prop. Valve drive axle right 03 Voltage above or shorted high Yellow
ECAS 42F39 Prop. Valve drive axle right 05 Current below nominal or open circuit Yellow
ECAS 42F39 Prop. Valve drive axle right 06 Current above nominal or grounded Yellow
circuit
ECAS 42F3A Prop. Valve 3° axle left 03 Voltage above or shorted high Yellow
ECAS 42F3A Prop. Valve 3° axle left 05 Current below nominal or open circuit Yellow
ECAS 42F3A Prop. Valve 3° axle left 06 Current above nominal or grounded Yellow
circuit
ECAS 42F3B Prop. Valve 3° axle right 03 Voltage above or shorted high Yellow
ECAS 42F3B Prop. Valve 3° axle right 05 Current below nominal or open circuit Yellow
ECAS 42F3B Prop. Valve 3° axle right 06 Current above nominal or grounded Yellow
circuit
ECAS 42FE7 Can bus off (SAE J 1939 Data link) 09 Abnormal update rate Yellow
ECAS 42F3C Can communication error 09 Abnormal update rate Yellow
ECAS 42F3D Can message VSC1 (CCVS) 09 Abnormal update rate Yellow
ECAS 42F3E Can message EEC1 09 Abnormal update rate Off
ECAS 42F3F Can message EBC2 09 Abnormal update rate Off
ECAS 42F40 Can message FFR_1 09 Abnormal update rate Off
ECAS 42F41 Can message ECAM1 09 Abnormal update rate Off
ECAS 42F42 Can message vehicle weight 09 Abnormal update rate Off
ECAS 42F43 Can message EBC5 09 Abnormal update rate Off
ECAS 42F44 Can message TCO1 09 Abnormal update rate Off
ECAS 42F45 Can message Time and Date 09 Abnormal update rate Off
ECAS 42F46 Can message ETC2 09 Abnormal update rate Off
ECAS 42F47 Can message ERC1-RD 09 Abnormal update rate Off
ECAS 42F48 Can message ERC1 - REX 09 Abnormal update rate Off
ECAS 42F49 Can message Articulation Inform 09 Abnormal update rate Off
ECAS 42F4A Can message EAC1 09 Abnormal update rate Off
ECAS 42F4B Can message ASC2_A 09 Abnormal update rate Off
ECAS 42F4C Can message ASC2_B 09 Abnormal update rate Off
ECAS 42F4D Can message ASC6_A 09 Abnormal update rate Off
ECAS 42F4E Can message ASC6_B 09 Abnormal update rate Off
ECAS 42F4F Can message Door Info 09 Abnormal update rate Yellow
ECAS 42F50 Speed signal 09 Abnormal update rate Yellow
ECAS 42F51 Brake switch 09 Abnormal update rate Yellow
ECAS 42F52 Parking brake switch 09 Abnormal update rate Off
ECAS 42F53 Engine speed 09 Abnormal update rate Off
ECAS 42F54 Supply pressure 09 Abnormal update rate Off
ECAS 42F55 Vehicle weight 09 Abnormal update rate Yellow
ECAS 42F56 Kneeling information 09 Abnormal update rate Off
ECAS 42F57 Door position 09 Abnormal update rate Yellow
ECAS 42F58 Level request information 0B Failure mode not identifiable Off
ECAS 42F59 Level control mode 03 Voltage above or shorted high Off
ECAS 42F59 Level control mode 05 Current below nominal or open circuit Off
ECAS 42F59 Level control mode 06 Current above nominal or grounded Off
circuit
ECAS 42F59 Level control mode 0B Failure mode not identifiable Off
ECAS 42F5A Damper stiffness 02 Data erratic, intermittent or incorrect Off
ECAS 42F5B Preset level 02 Data erratic, intermittent or incorrect Off
ECM 10019 Terminal 15 failure T15CD 02 no signal Eurocargo 6cyl Off Off
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 1001F SCR Temperatures plausibility SCRCatPlausIv 03 Temperature after Catalyst not plausible Eurocargo 6cyl Off On
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM SCR Temperatures plausibility SCRCatPlausIv 04 Temperature before Catalyst not Eurocargo 6cyl Off On
plausible Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 1001F SCR Temperatures plausibility SCRCatPlausIv 02 Ambient Temperature of Humidity Eurocargo 6cyl Off On
Sensor or both Catalyst Temperatures Trakker Cursor 8 (VGT/WG)
not plausible Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 1001F SCR Temperatures plausibility SCRCatPlausIv 0C Temperature Deviation between up- Eurocargo 6cyl Off On
and downstream Catalyst Temperature Trakker Cursor 8 (VGT/WG)
too high during Operation Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 20011 Vehicle Speed Sensor failure VSSCD2 03 Voltage too high Eurocargo 6cyl Off Off
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 20011 Vehicle Speed Sensor failure VSSCD2 04 Voltage too low Eurocargo 6cyl Off Off
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 20011 Vehicle Speed Sensor failure VSSCD2 02 CAN Signal failure Eurocargo 6cyl Off Off
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 20011 Vehicle Speed Sensor failure VSSCD2 0C Voltage not plausible Eurocargo 6cyl Off Off
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 2001D SCR Catalyst Thermal Ageing Limit SCRCatAgeingIv 03 Too High Catalyst Temperature for Eurocargo 6cyl Off Off
exceeded excessive duration Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 2001E SCR Catalyst Efficiency below first SCRCatNOxLvl1Iv 03 Nox above first OBD threshold (MIL On) Eurocargo 6cyl Off On
threshold Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 2001F Current of Boost Pressure Actuator out BPACOCurrOutRngIv 03 Ratio of desired and measured BPA Trakker Cursor 8 - VGT Off Off
of Range current out of range Trakker Cursor 13 - VGT
Trakker Militare Cursor 13
ECM 3001D DCU state monitoring SCRCatDCUStateIv 03 DCU not ready in time Eurocargo 6cyl Off On
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 3001E SCR Catalyst Efficiency below second SCRCatNOxLvl2Iv 03 Nox above second OBD threshold Eurocargo 6cyl Off On
threshold (Performance limitation) Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 3001F SCR Catalyst System Efficiency too high SCRCatHiEffIv 03 Efficiency too high Eurocargo 6cyl Yellow Off
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 10025 Main Relay 2 failure (Grid Heater 1, Fan MRlyCD 03 Short to Battery Eurocargo 6cyl Off Off
1, VGT, Lambda Heater, EGR Bypass Trakker Cursor 8 (VGT/WG)
Valve, EGR Actuator, Blow By Valve) Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 10025 Main Relay 2 failure (Grid Heater 1, Fan MRlyCD 04 Short to Ground Eurocargo 6cyl Off Off
1, VGT, Lambda Heater, EGR Bypass Trakker Cursor 8 (VGT/WG)
Valve, EGR Actuator, Blow By Valve) Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 10026 Battery voltage fault BattCD 03 Signal too high Eurocargo 6cyl Yellow Off
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 10026 Battery voltage fault BattCD 04 Signal too low Eurocargo 6cyl Yellow Off
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13

Bianca Andreana Trakker E4 Errors list Print Date: 21.11.2021

ELTRAC ET-TN-445-87 - Trakker E4 Error Codes Page 11 of 30

ECU SPN Fa ultComp one nt D

es
crip
tio
n F MI FM I C
omm
en
t L
amps
tat
u s M
ILL
amp
Na
m e [Hex] [
H e
x] D es
crip
tio
n
ECM 10027 Engine brake decompression valve CRERCD 03 Short to Battery Eurocargo 6cyl Yellow Off
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 10027 Engine brake decompression valve CRERCD 04 Short to Ground Eurocargo 6cyl Yellow Off
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 10027 Engine brake decompression valve CRERCD 02 Open Load Eurocargo 6cyl Yellow Off
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 10028 Main relay SCBatt (Lambda H./Grid MnRly1_SCB 03 Short to Battery Eurocargo 6cyl Yellow Off
H./Batt.switch) Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 10029 Main relay 3 (A/C compr./fuel filter MRlyCDMnRly3 03 Short to Battery Eurocargo 6cyl Off Off
heater) Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 10029 Main relay 3 (A/C compr./fuel filter MRlyCDMnRly3 04 Short to Ground Eurocargo 6cyl Off Off
heater) Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 1002A Main relay 4 (Exhaust valve eng.brake EVCD 03 Short to Battery or Open Load Eurocargo 6cyl Off Off
flap) Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 1002A Main relay 4 (Exhaust valve eng.brake EVCD 04 Short to Ground Eurocargo 6cyl Off Off
flap) Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 1002B Power stage air heater 1 actuator ArHt1 03 Short to Battery Eurocargo 6cyl Yellow Off
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 1002B Power stage air heater 1 actuator ArHt1 04 Short to Ground Eurocargo 6cyl Yellow Off
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 1002B Power stage air heater 1 actuator ArHt1 02 Open Load Eurocargo 6cyl Yellow Off
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 1002E Grid heater always switched on AirHtStickOnIv 03 Multi Signal failure Eurocargo 6cyl Yellow Off
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 20025 Main relay failure (Interrupted afterrun) MRlyCDAftRun 03 Relay opened too early (Afterrun not Eurocargo 6cyl Off On
completed) Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 20028 Main relay SCGND (Lambda H./Grid MnRly1_SCG 04 Short to Ground Eurocargo 6cyl Yellow Off
H./Batt.switch) Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 10031 Coolant temperature sensor CTSCD 03 Signal too high Eurocargo 6cyl Yellow Off
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 10031 Coolant temperature sensor CTSCD 04 Signal too low Eurocargo 6cyl Yellow Off
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 10031 Coolant temperature sensor CTSCD 02 CAN Signal failure Eurocargo 6cyl Yellow Off
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 10031 Coolant temperature sensor CTSCD 0C Signal not plausible to Oil Temperature Eurocargo 6cyl Yellow Off
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 10032 Coolant temperature sensor dynamic Clg_DynTst 0C Minimum Temperature Rise not Eurocargo 6cyl Off Off
test reached Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 10033 Boost Temp. Signal IATSCD 03 Signal too high Eurocargo 6cyl Off Off
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 10033 Boost Temp. Signal IATSCD 04 Signal too low Eurocargo 6cyl Off Off
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 10033 Boost Temp. Signal IATSCD 02 CAN Signal failure Eurocargo 6cyl Off Off
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 10034 Boost pressure sensor BPSCD 03 Signal too high Eurocargo 6cyl Yellow Off
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 10034 Boost pressure sensor BPSCD 04 Signal too low Eurocargo 6cyl Yellow Off
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 10034 Boost pressure sensor BPSCD 02 CAN Signal failure Eurocargo 6cyl Yellow Off
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 10034 Boost pressure sensor BPSCD 0C Signal not plausible Eurocargo 6cyl Yellow Off
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 10035 Fuel Temp. Signal FTSCD 03 Signal too high Eurocargo 6cyl Yellow Off
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 10035 Fuel Temp. Signal FTSCD 04 Signal too low Eurocargo 6cyl Yellow Off
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 10036 Rail pressure sensor CP3 RailCD 03 Signal too high Eurocargo 6cyl Red Off
ECM 10036 Rail pressure sensor CP3 RailCD 04 Signal too low Eurocargo 6cyl Red Off
ECM 10037 Common Rail pressure Limiting valve PRVMon 03 Valve open Eurocargo 6cyl Red Off
failure
ECM 10037 Rail pressure relief valve PRVMon 04 Pressure Shock requested (Valve does Eurocargo 6cyl Red Off
not open at Normal Opening Pressure)
ECM 10037 Rail pressure relief valve PRVMon 02 Valve did not open after Pressure Eurocargo 6cyl Red Off
Shock
ECM 10038 Oil Pressure Sensor failure OPSCD 03 Signal too high Eurocargo 6cyl Yellow Off
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 10038 Oil Pressure Sensor OPSCD 04 Signal too low Eurocargo 6cyl Yellow Off
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 10038 Oil Pressure Sensor OPSCD 02 Hardware failure Eurocargo 6cyl Yellow Off
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 10038 Oil Pressure Sensor OPSCD 0C Value too high Eurocargo 6cyl Yellow Off
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 1003A Oil Temp. Sensor OTSCD 03 Signal too high Eurocargo 6cyl Yellow Off
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 1003A Oil Temp. Sensor OTSCD 04 Signal too low Eurocargo 6cyl Yellow Off
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13

Bianca Andreana Trakker E4 Errors list Print Date: 21.11.2021

ELTRAC ET-TN-445-87 - Trakker E4 Error Codes Page 12 of 30

ECU SPN Fau ltCo

mpo
nen
t D
es
crip
tio
n F MI FMI C
omm
en
t L
amps
tat
u s M
ILL
amp
Na
m e [Hex] [
H e
x] D e scr
ipt
ion
ECM 1003A Oil Temp. Sensor OTSCD 02 CAN Signal failure Eurocargo 6cyl Yellow Off
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 1003A Oil Temp. Sensor OTSCD 0C Signal not plausible with Coolant Eurocargo 6cyl Yellow Off
Temperature Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 1003C Atmospheric Temperature EATSCD 03 Signal too high Eurocargo 6cyl Off Off
Sensor(Humidtiy?) Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 1003C Atmospheric Temperature EATSCD 04 Signal too low Eurocargo 6cyl Off Off
Sensor(Humidtiy?) Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 1003C Atmospheric Temperature EATSCD 02 CAN Signal failure Eurocargo 6cyl Off Off
Sensor(Humidtiy?) Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 20032 Coolant temperature sensor absolute ClgAbsTst 0C Minimum Temperature not reached in Eurocargo 6cyl Yellow Off
test time Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 20036 Rail pressure sensor offset monitoring RailCDOfsTst 03 Value above Limit Eurocargo 6cyl Yellow On
ECM 20036 Rail pressure sensor offset monitoring RailCDOfsTst 04 Value below Limit Eurocargo 6cyl Yellow On
ECM 20038 Oil Pressure too low OPSCD1 0C Value too low Eurocargo 6cyl Yellow Off
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 2003A Oil Temperature above normal OTSCD1 0C Temperature too high Eurocargo 6cyl Yellow Off
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 10041 Crankshaft sensor failure EngMCrS1 02 No Signal Eurocargo 6cyl Yellow On
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 10041 Crankshaft sensor failure EngMCrS2 04 Signal wrong Eurocargo 6cyl Yellow On
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 10042 Running with camshaft sensor only EngMBackUp 03 Backup Mode Eurocargo 6cyl Yellow Off
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 10043 Camshaft Speed sensor failure EngMCaS1 02 No Signal Eurocargo 6cyl Yellow Off
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 10043 Camshaft sensor failure EngMCaS2 04 Signal wrong Eurocargo 6cyl Yellow Off
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 10044 Offset between camshaft and cranksh. EngMOfsCaSCrS 03 Offset between Signals Eurocargo 6cyl Yellow On
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 10045 Fan Actuator 1 failure FanCD 03 Short to Battery Eurocargo 6cyl Yellow Off
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 10045 Fan Actuator 1 failure FanCD 04 Short to Ground Eurocargo 6cyl Yellow Off
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 10045 Fan Actuator 1 failure FanCD 02 Open Load Eurocargo 6cyl Yellow Off
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 10045 Fan Actuator 1 failure FanCD 0C Temperature too high Eurocargo 6cyl Yellow Off
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 2004A Engine Compartment Stop Button is ECBtCDStop 02 Button stuck Eurocargo 6cyl Off Off
stuck Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 1004D Engine overspeed protection EngPrtOvrSpd 03 Engine Overspeed Eurocargo 6cyl Off Off
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 1004F OBD Performance Limiter Intervention CoVehPrflmAct 03 Performance Limitation active Eurocargo 6cyl Yellow Off
by Legislation Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 1005B High Pressure Test (Rail Pressure HpTst 03 Test active Eurocargo 6cyl Off Off
Monitoring deactivated)
ECM 100A8 SCR Dosing Valve Overheat Protection FrmMngSCR1ProtIv 03 Torque Limitation Level2 for SCR Eurocargo 6cyl Yellow Off
Protection active Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 100A8 SCR Dosing Valve Overheat Protection FrmMngSCR1ProtIv 04 Torque Limitation Level1 for SCR Eurocargo 6cyl Yellow Off
Protection active Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 100AF DCU Error1 via CAN message DM1DCU FrmMngDM1SPN1Iv 03 Error in DCU active Eurocargo 6cyl Off Off
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 100B9 MIL visualization not available FrmMngBC1MILIv 03 MIL visualization not available Eurocargo 6cyl Yellow On
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 2009D Torque Limitation due to Negative NTCTrqLim 04 Torque Limitation Eurocargo 6cyl Off Off
Torque Coordinator Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 200AF DCU Error2 via CAN message DM1DCU FrmMngDM1SPN2Iv 03 Error in DCU active Eurocargo 6cyl Off on
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 3009E Torque Limitation due to Turbo Charger BstPrtTrqLim 03 Torque Limitation Eurocargo 6cyl Off Off
Protection Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 4009E Info: Torque Limitation due to Engine EngPrtTrqLim 03 Torque Limitation Eurocargo 6cyl Off Off
Protection (against Excessive Torque, Trakker Cursor 8 (VGT/WG)
Engine Overspeed and Overheat) Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 400AF DCU Error4 via CAN message DM1DCU FrmMngDM1SPN4Iv 03 Error in DCU active Eurocargo 6cyl Off on
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 5009D Torque Limitation due to SCR Catalyst SCRPrtTrqLim 04 Torque Limitation Eurocargo 6cyl Off Off
Overheat Protection Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 5009E Torque Limitation due to Noise NsCtlTrqLim 04 Torque Limitation Eurocargo 6cyl Off Off
Limitation Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 500AF DCU Error5 via CAN message DM1DCU FrmMngDM1SPN5Iv 03 Error in DCU active Eurocargo 6cyl Off on
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 6009E Torque Limitation due to Fuel Quantity QLimTrqLim 04 Torque Limitation Eurocargo 6cyl Off Off
Limitation because of Injection System Trakker Cursor 8 (VGT/WG)
Errors Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 10051 Cylinder 1 BIP search failure BIPCyl1 03 Too many unsuccessful searches Trakker Cursor 8 (VGT/WG) Yellow On
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 10052 Cylinder 2 BIP search failure BIPCyl2 03 Too many unsuccessful searches Trakker Cursor 8 (VGT/WG) Yellow On
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13

Bianca Andreana Trakker E4 Errors list Print Date: 21.11.2021

ELTRAC ET-TN-445-87 - Trakker E4 Error Codes Page 13 of 30

ECU SPN Fau ltCo mp o n en t D

es
crip
tio
n F MI FM I C
omm
en
t L
amps
tat
u s M
ILL
amp
Na
m e [Hex] [
H e
x] Descriptio n
ECM 10053 Cylinder 3 BIP search failure BIPCyl3 03 Too many unsuccessful searches Trakker Cursor 8 (VGT/WG) Yellow On
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 10054 Cylinder 4 BIP search failure BIPCyl4 03 Too many unsuccessful searches Trakker Cursor 8 (VGT/WG) Yellow On
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 10055 Cylinder 5 BIP search failure BIPCyl5 03 Too many unsuccessful searches Trakker Cursor 8 (VGT/WG) Yellow On
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 10056 Cylinder 6 BIP search failure BIPCyl6 03 Too many unsuccessful searches Trakker Cursor 8 (VGT/WG) Yellow On
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 10052 Rail Pressure Positive Deviation High RailMeUn1 03 Positive Deviation too High Concerning Eurocargo 6cyl Red Off
and High Fuel Flow Setpoint Value Fuel Flow
ECM 10053 Rail Pressure Negative Deviation too RailMeUn2 03 Fuel pressure too high with closed Eurocargo 6cyl Red Off
High on Minimum Metering Metering Unit
ECM 10054 Rail Pressure below Minimum Limit in RailMeUn3 03 Rail Pressure too low Eurocargo 6cyl Red Off
Controlled Mode
ECM 10055 Rail Pressure above Maximum Limit in RailMeUn4 03 Rail Pressure too high Eurocargo 6cyl Red Off
Controlled Mode
ECM 10056 Rail Pressure Drop Rate too High RailMeUn6 03 Rail Pressure Drop Rate Higher then Eurocargo 6cyl Yellow Off
expected
ECM 10057 Setpoint of metering unit in overrun RailMeUn7 03 Metering Unit excessively opened to Eurocargo 6cyl Yellow Off
mode not plausible reached desired Rail pressure
ECM 10058 Fuel Flow Setpoint of Common Rail RailMeUn10 03 Fuel System Leakage or Metering Unit Eurocargo 6cyl Yellow Off
Metering Unit too low jammed in closed position
ECM 10059 Common Rail Metering Unit Power MeUnCDNoLoad 02 Open Load Eurocargo 6cyl Yellow Off
Stage failure
ECM 10059 Metering unit PWM-powerstage MeUnCDNoLoad 0C Temperature too high Eurocargo 6cyl Yellow Off
ECM 20059 Common Rail Metering Unit Power MeUnCDSCBat 03 Short to Battery Eurocargo 6cyl Yellow Off
Stage Short to Battery
ECM 30059 Common Rail Metering Unit Power MeUnCDSCGnd 04 Short to Ground Eurocargo 6cyl Off Off
Stage Short to Ground
ECM 1005F Long Term Fuel system Failure OBDGFClct1 03 Long Term Fault present (not deletable Eurocargo 6cyl Off On
until after 400 days) Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 2005F Long Term Injection timing Failure OBDGFClct2 03 Long Term Fault present (not deletable Eurocargo 6cyl Off On
until after 400 days) Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 3005F Long Term air system failure OBDGFClct3 03 Long Term Fault present (not deletable Eurocargo 6cyl Off On
until after 400 days) Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 4005F Long Term NOx Sensor Failure OBDGFClct4 03 Long Term Fault present (not deletable Eurocargo 6cyl Off On
until after 400 days) Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 5005F Long Term SCR System Failure OBDGFClct5 03 Long Term Fault present (not deletable Eurocargo 6cyl Off On
until after 400 days) Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 10061 Injector Cylinder 1 failure InjVlvCyl1A 03 Short Low Side to Battery Eurocargo 6cyl Yellow On
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 10061 Injector Cylinder 1 failure InjVlvCyl1A 04 Depending on Application Eurocargo 6cyl Yellow On
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 10061 Injector Cylinder 1 failure InjVlvCyl1A 02 Short High Side to Ground Eurocargo 6cyl Yellow On
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 10061 Injector Cylinder 1 failure InjVlvCyl1A 0C Not classifiable failure Eurocargo 6cyl Yellow On
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 10062 Injector Cylinder 2 failure InjVlvCyl2A 03 Short Low Side to Battery Eurocargo 6cyl Yellow On
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 10062 Injector Cylinder 2 failure InjVlvCyl2A 04 Depending on Application Eurocargo 6cyl Yellow On
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 10062 Injector Cylinder 2 failure InjVlvCyl2A 02 Short High Side to Ground Eurocargo 6cyl Yellow On
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 10062 Injector Cylinder 2 failure InjVlvCyl2A 0C Not classifiable failure Eurocargo 6cyl Yellow On
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 10063 Injector Cylinder 3 failure InjVlvCyl3A 03 Short Low Side to Battery Eurocargo 6cyl Yellow On
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 10063 Injector Cylinder 3 failure InjVlvCyl3A 04 Depending on Application Eurocargo 6cyl Yellow On
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 10063 Injector Cylinder 3 failure InjVlvCyl3A 02 Short High Side to Ground Eurocargo 6cyl Yellow On
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 10063 Injector Cylinder 3 failure InjVlvCyl3A 0C Not classifiable failure Eurocargo 6cyl Yellow On
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 10064 Injector Cylinder 4 failure InjVlvCyl4A 03 Short Low Side to Battery Eurocargo 6cyl Yellow On
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 10064 Injector Cylinder 4 failure InjVlvCyl4A 04 Depending on Application Eurocargo 6cyl Yellow On
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 10064 Injector Cylinder 4 failure InjVlvCyl4A 02 Short High Side to Ground Eurocargo 6cyl Yellow On
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 10064 Injector Cylinder 4 failure InjVlvCyl4A 0C Not classifiable failure Eurocargo 6cyl Yellow On
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 10065 Injector Cylinder 5 failure InjVlvCyl5A 03 Short Low Side to Battery Eurocargo 6cyl Yellow On
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 10065 Injector Cylinder 5 failure InjVlvCyl5A 04 Depending on Application Eurocargo 6cyl Yellow On
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 10065 Injector Cylinder 5 failure InjVlvCyl5A 02 Short High Side to Ground Eurocargo 6cyl Yellow On
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 10065 Injector Cylinder 5 failure InjVlvCyl5A 0C Not classifiable failure Eurocargo 6cyl Yellow On
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 10066 Injector Cylinder 6 failure InjVlvCyl6A 03 Short Low Side to Battery Eurocargo 6cyl Yellow On
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 10066 Injector Cylinder 6 failure InjVlvCyl6A 04 Depending on Application Eurocargo 6cyl Yellow On
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 10066 Injector Cylinder 6 failure InjVlvCyl6A 02 Short High Side to Ground Eurocargo 6cyl Yellow On
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13

Bianca Andreana Trakker E4 Errors list Print Date: 21.11.2021

ELTRAC ET-TN-445-87 - Trakker E4 Error Codes Page 14 of 30

ECU SPN F aultC o m p one

nt D
es
crip
tio
n F MI F M I C
omm
en
t L
amps
tat
u s M
ILL
amp
Na
m e [Hex] [
H e
x] De s c r
ip t
ion
ECM 10066 Injector Cylinder 6 failure InjVlvCyl6A 0C Not classifiable failure Eurocargo 6cyl Yellow On
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 10067 Injector Cylinder 1 warning InjVlvCyl1B 03 Depending on Application Eurocargo 6cyl Yellow On
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 10067 Injector Cylinder 1 warning InjVlvCyl1B 04 Depending on Application Eurocargo 6cyl Yellow On
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 10067 Injector Cylinder 1 warning InjVlvCyl1B 02 Open Load Eurocargo 6cyl Yellow On
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 10067 Injector Cylinder 1 warning InjVlvCyl1B 0C Depending on Application Eurocargo 6cyl Yellow On
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 10068 Injector Cylinder 2 warning InjVlvCyl2B 03 Depending on Application Eurocargo 6cyl Yellow On
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 10068 Injector Cylinder 2 warning InjVlvCyl2B 04 Depending on Application Eurocargo 6cyl Yellow On
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 10068 Injector Cylinder 2 warning InjVlvCyl2B 02 Open Load Eurocargo 6cyl Yellow On
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 10068 Injector Cylinder 2 warning InjVlvCyl2B 0C Depending on Application Eurocargo 6cyl Yellow On
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 10069 Injector Cylinder 3 warning InjVlvCyl3B 03 Depending on Application Eurocargo 6cyl Yellow On
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 10069 Injector Cylinder 3 warning InjVlvCyl3B 04 Depending on Application Eurocargo 6cyl Yellow On
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 10069 Injector Cylinder 3 warning InjVlvCyl3B 02 Open Load Eurocargo 6cyl Yellow On
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 10069 Injector Cylinder 3 warning InjVlvCyl3B 0C Depending on Application Eurocargo 6cyl Yellow On
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 1006A Injector Cylinder 4 warning InjVlvCyl4B 03 Depending on Application Eurocargo 6cyl Yellow On
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 1006A Injector Cylinder 4 warning InjVlvCyl4B 04 Depending on Application Eurocargo 6cyl Yellow On
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 1006A Injector Cylinder 4 warning InjVlvCyl4B 02 Open Load Eurocargo 6cyl Yellow On
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 1006A Injector Cylinder 4 warning InjVlvCyl4B 0C Depending on Application Eurocargo 6cyl Yellow On
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 1006B Injector Cylinder 5 warning InjVlvCyl5B 03 Depending on Application Eurocargo 6cyl Yellow On
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 1006B Injector Cylinder 5 warning InjVlvCyl5B 04 Depending on Application Eurocargo 6cyl Yellow On
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 1006B Injector Cylinder 5 warning InjVlvCyl5B 02 Open Load Eurocargo 6cyl Yellow On
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 1006B Injector Cylinder 5 warning InjVlvCyl5B 0C Depending on Application Eurocargo 6cyl Yellow On
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 1006C Injector Cylinder 6 warning InjVlvCyl6B 03 Depending on Application Eurocargo 6cyl Yellow On
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 1006C Injector Cylinder 6 warning InjVlvCyl6B 04 Depending on Application Eurocargo 6cyl Yellow On
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 1006C Injector Cylinder 6 warning InjVlvCyl6B 02 Open Load Eurocargo 6cyl Yellow On
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 1006C Injector Cylinder 6 warning InjVlvCyl6B 0C Depending on Application Eurocargo 6cyl Yellow On
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 1006E The minimum number of injections was InjVlvNumMinInj 03 Number of Injections not reached Eurocargo 6cyl Red Off
not reached --> stop the engine Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 10071 Injector Bank 1 failure InjVlvBnk1A 03 Short circuit Eurocargo 6cyl Yellow On
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 10071 Bank 1 specific errors - Short circuit / not InjVlvBnk1A 04 Short Low Side to Ground Eurocargo 6cyl Yellow On
classifyable Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 10071 Bank 1 specific errors - Short circuit / not InjVlvBnk1A 02 Depending on Application Eurocargo 6cyl Yellow On
classifyable Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 10071 Bank 1 specific errors - Short circuit / not InjVlvBnk1A 0C Not classifiable failure Eurocargo 6cyl Yellow On
classifyable Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 10073 Injector Bank 2 failure InjVlvBnk2A 03 Short circuit Eurocargo 6cyl Yellow On
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 10073 Bank 2 specific errors - Short circuit / not InjVlvBnk2A 04 Short Low Side to Ground Eurocargo 6cyl Yellow On
classifyable Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 10073 Bank 2 specific errors - Short circuit / not InjVlvBnk2A 02 Depending on Application Eurocargo 6cyl Yellow On
classifyable Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 10073 Bank 2 specific errors - Short circuit / not InjVlvBnk2A 0C Not classifiable failure Eurocargo 6cyl Yellow On
classifyable Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 1007C ECU Hardware for Injection: CY33X InjVlvChipA 03 Internal reset - Clock Loss - Voltage too Eurocargo 6cyl Yellow Off
Chip specific failure (1) low Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 1007C Chip-specific errors-->stop engine InjVlvChipA 04 Unlocked - Init fail Eurocargo 6cyl Yellow Off
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13

Bianca Andreana Trakker E4 Errors list Print Date: 21.11.2021

ELTRAC ET-TN-445-87 - Trakker E4 Error Codes Page 15 of 30

ECU SPN F au ltCo m po nent D

es
crip
tio
n F MI F
M I C
omm
en
t L
amps
tat
u s M
ILL
amp
Na
m e [Hex] [
H e
x] D
es
crip
tio
n
ECM 1007C Chip-specific errors-->stop engine InjVlvChipA 02 Test Mode Eurocargo 6cyl Yellow Off
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 1007C Chip-specific errors-->stop engine InjVlvChipA 0C SPI Communication failure Eurocargo 6cyl Yellow Off
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 1007F Failure in Injection Quantity Adjustment InjVlvQntAdj 02 EEPROM Adjustment Value not Trakker Cursor 8 (VGT/WG) Yellow Off
(NIMA Programming) readable Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 1007F Problem in programmed IMA/NIMA code InjVlvQntAdj 0C Invalid EEPROM Adjustment Value Trakker Cursor 8 (VGT/WG) Yellow Off
Checksum Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 2007C ECU Hardware for Injection: CY33X InjVlvChipB 03 Internal reset - Clock loss - Voltage too Eurocargo 6cyl Yellow Off
Chip specific failure (2) low Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 2007C Chip-specific errors-->stop engine InjVlvChipB 04 Unlocked - Init fail Eurocargo 6cyl Yellow Off
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 2007C Chip-specific errors-->stop engine InjVlvChipB 02 Test Mode Eurocargo 6cyl Yellow Off
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 2007C Chip-specific errors-->stop engine InjVlvChipB 0C SPI Communication failure Eurocargo 6cyl Yellow Off
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 10081 Differential Pressure Sensor Failure IEDPCDPDiff 03 Signal too high Eurocargo 6cyl Yellow On
between Exhaust and Intake (EGR Trakker Cursor 8 (VGT/WG)
Valve) Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 10081 Differential Pressure Sensor Failure IEDPCDPDiff 04 Signal too low Eurocargo 6cyl Yellow On
between Exhaust and Intake (EGR Trakker Cursor 8 (VGT/WG)
Valve) Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 10091 Boost Pressure Actuator Current failure BPACD_ADC 03 Signal too high Trakker Cursor 8 - VGT Yellow Off
Trakker Cursor 13 - VGT
Trakker Militare Cursor 13
ECM 10091 Boost pressure actuator current BPACD_ADC 04 Signal too low Trakker Cursor 8 - VGT Yellow Off
AD-channel Trakker Cursor 13 - VGT
Trakker Militare Cursor 13
ECM 10091 Boost pressure actuator current BPACD_ADC 02 Signal not plausible Trakker Cursor 8 - VGT Yellow Off
AD-channel Trakker Cursor 13 - VGT
Trakker Militare Cursor 13
ECM 10092 Boost Pressure Actuator Short to Battery BPACD_Max 03 Short to Battery Trakker Cursor 8 - VGT Yellow Off
Trakker Cursor 13 - VGT
Trakker Militare Cursor 13
ECM 10093 Turbine speed sensor TSSCD 03 Signal too high Trakker Cursor 8 - VGT Yellow Off
Trakker Cursor 13 - VGT
Trakker Militare Cursor 13
ECM 10093 Turbine speed TSSCD 04 Signal too low Trakker Cursor 8 - VGT Yellow Off
Trakker Cursor 13 - VGT
Trakker Militare Cursor 13
ECM 10093 Turbine speed TSSCD 02 Signal not valid Trakker Cursor 8 - VGT Yellow Off
Trakker Cursor 13 - VGT
Trakker Militare Cursor 13
ECM 10093 Turbine speed TSSCD 0C Signal not plausible Trakker Cursor 8 - VGT Yellow Off
Trakker Cursor 13 - VGT
Trakker Militare Cursor 13
ECM 10098 Turbocharger Control failure PCRMulSigDfctIv 03 Multi Signal failure Trakker Cursor 8 - VGT Yellow Off
Trakker Cursor 13 - VGT
Trakker Militare Cursor 13
ECM 10099 Turbocharger Control Boost Pressure PCRP2Iv 03 Pressure too high Trakker Cursor 8 - VGT Yellow Off
failure Trakker Cursor 13 - VGT
Trakker Militare Cursor 13
ECM 10099 P2 pressure errors in PCR PCRP2Iv 02 Pressure deviation too high Trakker Cursor 8 - VGT Yellow Off
Trakker Cursor 13 - VGT
Trakker Militare Cursor 13
ECM 1009A Turbocharger Control Turbo Speed PCRTrbIv 03 Reversible Overspeed Trakker Cursor 8 - VGT Yellow Off
failure Trakker Cursor 13 - VGT
Trakker Militare Cursor 13
ECM 1009A Turbine speed errors in PCR PCRTrbIv 02 Irreversible Overspeed Trakker Cursor 8 - VGT Yellow Off
Trakker Cursor 13 - VGT
Trakker Militare Cursor 13
ECM 1009B Turbine Overspeed at Normal TrbChIv 03 Irreversible turbine overspeed Trakker Cursor 8 - VGT Yellow Off
Atmospheric Pressure Trakker Cursor 13 - VGT
Trakker Militare Cursor 13
ECM 1009E Torque Reduction due to Smoke SmkTrqLim 04 Torque Limitation Eurocargo 6cyl Off Off
Limitation Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 1009F NOx Estimation failure NOxEstlv 03 Estimated Nox signal not reliable Eurocargo 6cyl Off Off
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 20092 Boost Pressure Actuator Short to BPACD_Min 04 Short to Ground Trakker Cursor 8 - VGT Yellow Off
Ground Trakker Cursor 13 - VGT
Trakker Militare Cursor 13
ECM 20099 Turbocharger Control Underboost PCRUndBstIv 03 Pressure too low Trakker Cursor 8 - VGT Yellow On
Pressure failure Trakker Cursor 13 - VGT
Trakker Militare Cursor 13
ECM 30092 Boost Pressure Power Stage open load BPACD_SigNpl 02 Open Load Trakker Cursor 8 - VGT Yellow Off
or high Temperature Trakker Cursor 13 - VGT
Trakker Militare Cursor 13
ECM 30092 Boost Pressure Power Stage open load BPACD_SigNpl 0C Temperature too high Trakker Cursor 8 - VGT Yellow Off
or high Temperature Trakker Cursor 13 - VGT
Trakker Militare Cursor 13
ECM 100A2 NOx Sensor Plausiblity failure 0C Signal not plausible Eurocargo 6cyl Off On
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
FrmMngNOxSensNOxIv Trakker Militare Cursor 13
ECM 100A3 NOx Sensor Failure 03 Open Load Eurocargo 6cyl Off On
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
FrmMngNOxSensIv Trakker Militare Cursor 13
ECM 100A3 NOx Sensor Failure 04 Short Circuit Eurocargo 6cyl Off On
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
FrmMngNOxSensIv Trakker Militare Cursor 13
ECM 100A3 NOx Sensor Failure 0C Sensor not ready in time Eurocargo 6cyl Off On
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
FrmMngNOxSensIv Trakker Militare Cursor 13
ECM 100A4 CAN Message timeout Nox (from Nox FrmMngTONOxSensIv 02 CAN timeout Eurocargo 6cyl Off On
Sensor) Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 100A5 CAN Message timeout DM1DCU (from FrmMngTODM1DCUIv 02 CAN timeout Eurocargo 6cyl Yellow On
DCU) Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 100A6 CAN Message timeout SCR1 (from FrmMngTOSCR1Iv 02 CAN timeout Eurocargo 6cyl Yellow On
DCU) Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 100AE Humidity Sensor Signal Ratio failure 03 Signal Ratio above Limit Eurocargo 6cyl Off Off
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
IAHSCDStrtDly Trakker Militare Cursor 13
ECM 100AE Humidity Sensor Signal Ratio failure 04 Signal Ratio below Limit Eurocargo 6cyl Off Off
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
IAHSCDStrtDly Trakker Militare Cursor 13
ECM 200A2 NOx Sensor Drift failure SCRCatNOxDrIv 03 Zero Drift detected Eurocargo 6cyl Off On
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 200A6 CAN Message timeout SCR2 (from FrmMngTOSCR2Iv 02 CAN timeout Eurocargo 6cyl Yellow On
DCU) Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13

Bianca Andreana Trakker E4 Errors list Print Date: 21.11.2021

ELTRAC ET-TN-445-87 - Trakker E4 Error Codes Page 16 of 30

ECU SPN Fa ultC

om p o nen t D
es
crip
tio
n F MI F M I C
omm
en
t L
amps
tat
u s M
ILL
amp
Na
m e [Hex] [
H e
x] Desc rip
tio n
ECM 200AE Humidity Sensor possibly saturated with IAHSCD 03 Signal Ratio above Limit Eurocargo 6cyl Off Off
water droplets Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 200AE Info: Humidity Sensor possibly saturated IAHSCD 04 Signal Ratio below Limit Eurocargo 6cyl Off Off
with water droplets Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 300A2 NOx Sensor Plausibility failure SCRCatNOxPlIv 03 Difference between measured and Eurocargo 6cyl Off On
simulated Value not plausible Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 100B1 Busoff in CAN A NetMngCANAOff 03 CAN Bus off Eurocargo 6cyl Off Off
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 100B2 Busoff in CAN B NetMngCANBOff 03 CAN Bus off Eurocargo 6cyl Off Off
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 100B3 Busoff in CAN C NetMngCANCOff 03 CAN Bus off Eurocargo 6cyl Off Off
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 100B4 Timeout for BC2EDC1 FrmMngTOBC2EDC1Iv 02 CAN timeout Eurocargo 6cyl Yellow Off
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 100B5 Timeout for VM2EDC FrmMngTOVM2EDCIv 02 CAN timeout Eurocargo 6cyl Yellow Off
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 100B7 Timeout in CAN transmit messages FrmMngTxTO 02 CAN timeout Eurocargo 6cyl Yellow On
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 100BA Message Dashboard Display timeout FrmMngTODashDsplIv 02 CAN timeout Eurocargo 6cyl Off Off
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 100BC CAN Message timeout AMCON (from FrmMngTORxAMCONIv 02 CAN timeout Eurocargo 6cyl Off Off
VCM) Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 100BD CAN Message timeout CCVS (from FrmMngTORxCCVS 02 CAN timeout Eurocargo 6cyl Off Off
Body Computer or VCM) Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 200B4 Timeout for BC2EDC2 FrmMngTOBC2EDC2Iv 02 CAN timeout Eurocargo 6cyl Yellow Off
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 100C2 Timeout of CAN message ETC1 FrmMngTOETC1 02 CAN timeout Eurocargo 6cyl Yellow Off
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 100C3 Timeout of CAN message TCO1 FrmMngTOTCO1 02 CAN timeout Eurocargo 6cyl Off Off
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 100C6 Timeout of CAN message TSC1-PE FrmMngTOTSC1PEActIv 03 CAN timeout Eurocargo 6cyl Yellow Off
active Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 100C8 Timeout of CAN message TSC1-VE FrmMngTOTSC1VEActIv 03 CAN timeout Eurocargo 6cyl Yellow Off
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 200C2 Timeout of CAN message ETC2 FrmMngTOETC2 02 CAN timeout Eurocargo 6cyl Off Off
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 200C6 Timeout of CAN message TSC1-PE FrmMngTOTSC1PEPasIv 02 CAN timeout Eurocargo 6cyl Yellow Off
passive Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 200C8 Timeout of CAN message TSC1-VR FrmMngTOTSC1VRActIv 03 CAN timeout Eurocargo 6cyl Yellow Off
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 200C9 Timeout for message TimeDate FrmMngTOTimeDateIv 02 CAN timeout Eurocargo 6cyl Off Off
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 300C8 Timeout of CAN message TSC1-VE FrmMngTOTSC1VEPasIv 02 CAN timeout Eurocargo 6cyl Yellow Off
passive Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 300C9 Timeout for message HRVD (high FrmMngTOHRVDIv 02 CAN timeout Eurocargo 6cyl Off Off
resolution vehicle distance) Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 400C8 Timeout of CAN message TSC1-VR FrmMngTOTSC1VRPasIv 02 CAN timeout Eurocargo 6cyl Yellow Off
passive Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 100D1 ECU Hardware: SPI Communication HWEMonCom 03 CJ940 Communication failure Eurocargo 6cyl Red Off
failure Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 100D2 ECU Hardware: EEPROM failure HWEMonEEPROM 04 Read failure Eurocargo 6cyl Off Off
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 100D2 ECU Hardware: EEPROM failure HWEMonEEPROM 02 Write failure Eurocargo 6cyl Off Off
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 100D2 ECU Hardware: EEPROM failure HWEMonEEPROM 0C Default Value used Eurocargo 6cyl Off Off
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 100D3 ECU recovery - locked HWEMonRcyLocked 0C Recovery occurred Eurocargo 6cyl Red Off
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 100D4 ECU Hardware: Microcontroller Montr 0C Watchdog and Controller not plausible Eurocargo 6cyl Yellow Off
Watchdog failure Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 100D5 ECU Hardware: Shut off during SOPTst 04 Watchdog Eurocargo 6cyl Yellow Off
Initialization Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 100D5 ECU Hardware: Shut off during SOPTst 02 Supply Voltage too high Eurocargo 6cyl Yellow Off
Initialization Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 100D5 ECU Hardware: Shut off during SOPTst 0C Supply Voltage too low Eurocargo 6cyl Yellow Off
Initialization Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 100D6 ECU Hardware: TPU Monitoring TPUMon 0C Time deviation between System and Eurocargo 6cyl Yellow Off
TPU Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 100D7 ECU Software: Variant Dataset failure VarMngCodDs 02 Variant Dataset not valid Eurocargo 6cyl Red Off
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 100D7 ECU Software: Variant Dataset failure VarMngCodDs 0C Variant could not be set Eurocargo 6cyl Red Off
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13

Bianca Andreana Trakker E4 Errors list Print Date: 21.11.2021

ELTRAC ET-TN-445-87 - Trakker E4 Error Codes Page 17 of 30

ECU SPN F
a ultC om p o nent D
es
crip
tio
n F MI FM I C
omm
en
t L
amps
tat
u s M
ILL
amp
Na
m e [Hex] [
H e
x] De scrip tion
ECM 100D8 ECU Hardware: Controller Watchdog WdCom 0C SPI Communication failure Eurocargo 6cyl Yellow Off
failure Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 100D9 ADC Monitoring failure ADCMon 03 Reference Voltage too high Eurocargo 6cyl Yellow Off
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 100D9 ADC Monitoring failure ADCMon 04 Reference Voltage too low Eurocargo 6cyl Yellow Off
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 100D9 ADC Monitoring failure ADCMon 02 Test Impulse Error Eurocargo 6cyl Yellow Off
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 100D9 ADC Monitoring failure ADCMon 0C Queue Error Eurocargo 6cyl Yellow Off
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 200D3 ECU recovery - suppressed HWEMonRcySuppressed 0C Recovery occurred Eurocargo 6cyl Red Off
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 300D3 ECU recovery - visible HWEMonRcyVisible 0C Recovery occurred Eurocargo 6cyl Red Off
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 100E1 ECU Hardware: High Side Power Stage StrtCDHS 03 Short to Battery Eurocargo 6cyl Yellow Off
Short to Ground or Battery
ECM 100E1 ECU Hardware: High Side Power Stage StrtCDHS 04 Short to Ground Eurocargo 6cyl Yellow Off
Short to Ground or Battery
ECM 100E2 Immobilizer failure (no fuel release) ImmCtl 04 Injection disabled Eurocargo 6cyl Red Off
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 100E3 Overrun Monitoring failure OvRMon 03 Injection Time too long Eurocargo 6cyl Red Off
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 100E4 Redundant Engine Speed in Overrun OvRMonSigA 03 Speed Signal not plausible Eurocargo 6cyl Red Off
Monitoring Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 100E5 ECU Hardware: Sensor 12V Supply SSpMon12V 03 Signal too high Eurocargo 6cyl Yellow Off
Voltage failure Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 100E5 ECU Hardware: Sensor 12V Supply SSpMon12V 04 Signal too low Eurocargo 6cyl Yellow Off
Voltage failure Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 100E6 ECU Hardware: Sensor Supply Voltage SSpMon1 03 Signal too high Eurocargo 6cyl Yellow On
1 failure Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 100E6 ECU Hardware: Sensor Supply Voltage SSpMon1 04 Signal too low Eurocargo 6cyl Yellow On
1 failure Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 100E7 ECU Hardware: Sensor Supply Voltage SSpMon2 03 Signal too high Eurocargo 6cyl Yellow Off
2 failure Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 100E7 ECU Hardware: Sensor Supply Voltage SSpMon2 04 Signal too low Eurocargo 6cyl Yellow Off
2 failure Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 100E8 ECU Hardware: Sensor Supply Voltage SSpMon3 03 Signal too high Eurocargo 6cyl Yellow Off
3 failure Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 100E8 ECU Hardware: Sensor Supply Voltage SSpMon3 04 Signal too low Eurocargo 6cyl Yellow Off
3 failure Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 100E9 ECU internal Supply Voltage too high HWEMonUMaxSupply 03 Supply Voltage CJ940 above Limit Eurocargo 6cyl Red Off
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 100EA ECU internal Supply Voltage too low HWEMonUMinSupply 04 Supply Voltage CJ940 below Limit Eurocargo 6cyl Red Off
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 100EB Atmospheric Pressure Sensor APSCD 03 Signal too high Eurocargo 6cyl Off Off
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 100EB Atmospheric Pressure Sensor APSCD 04 Signal too low Eurocargo 6cyl Off Off
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 100EB Atmospheric Pressure Sensor APSCD 02 CAN Signal failure Eurocargo 6cyl Off Off
Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 100EB Atmospheric Pressure Sensor APSCD 0C Signal not plausible to Reference Eurocargo 6cyl Off Off
Pressure (Boost or Exhaust) Trakker Cursor 8 (VGT/WG)
Trakker Cursor 13 (VGT/WG)
Trakker Militare Cursor 13
ECM 200E1 ECU Hardware: Low Side Power Stage StrtCDLS 03 Short to Battery or excess temperature Eurocargo 6cyl Yellow Off
Short to Ground or Battery
ECM 200E1 ECU Hardware: Low Side Power Stage StrtCDLS 04 Short to Ground Eurocargo 6cyl Yellow Off
Short to Ground or Battery
ECM 200E1 ECU Hardware: Low Side Power Stage StrtCDLS 02 Open Load Eurocargo 6cyl Yellow Off
Short to Ground or Battery
EM 47222 PTO1 solenoid valve 03 Voltage above normal, or shorted to Yellow
high source
EM 47222 PTO1 solenoid valve 04 Voltage below normal, or shorted to low Yellow
source
EM 47222 PTO1 solenoid valve 05 Current below normal or open circuit Yellow
EM 47223 PTO2 solenoid valve 03 Voltage above normal, or shorted to Yellow
high source
EM 47223 PTO2 solenoid valve 04 Voltage below normal, or shorted to low Yellow
source
EM 47223 PTO2 solenoid valve 05 Current below normal or open circuit Yellow
EM 47224 PTO3 solenoid valve 03 Voltage above normal, or shorted to Yellow
high source
EM 47224 PTO3 solenoid valve 04 Voltage below normal, or shorted to low Yellow
source
EM 47224 PTO3 solenoid valve 05 Current below normal or open circuit Yellow
EM 47230 PTO MODULE: PTO1 engagement 02 Data erratic, intermittent or incorrect Yellow
restriction
EM 47231 PTO MODULE: PTO1 shutoff condition 02 Data erratic, intermittent or incorrect Yellow
EM 47232 PTO MODULE: PTO1 engagement 0D Special instructions Yellow
timeout
EM 47233 PTO MODULE: PTO1 disengagement 0D Special instructions Yellow
timeout
EM 47234 PTO MODULE: PTO1 unrequested 0D Special instructions Yellow
engagement
EM 47235 PTO MODULE: PTO1 unrequested 0D Special instructions Yellow
disengagement
EM 47236 PTO MODULE: PTO2 engagement 02 Data erratic, intermittent or incorrect Yellow
restriction
EM 47237 PTO MODULE: PTO2 shutoff condition 02 Data erratic, intermittent or incorrect Yellow
EM 47238 PTO MODULE: PTO2 engagement 0D Special instructions Yellow
timeout
EM 47239 PTO MODULE: PTO2 disengagement 0D Special instructions Yellow
timeout
EM 4723A PTO MODULE: PTO2 unrequested 0D Special instructions Yellow
engagement
EM 4723B PTO MODULE: PTO2 unrequested 0D Special instructions Yellow
disengagement
EM 4723C PTO MODULE: PTO3 engagement 02 Data erratic, intermittent or incorrect Yellow
restriction
EM 4723D PTO MODULE: PTO3 shutoff condition 02 Data erratic, intermittent or incorrect Yellow

Bianca Andreana Trakker E4 Errors list Print Date: 21.11.2021

ELTRAC ET-TN-445-87 - Trakker E4 Error Codes Page 18 of 30

EC
U SPN F au ltCo mp on en t D
es
crip
tio
n F MI F MI C
omm
en
t L
amps
tat
u s M
ILL
amp
N
ame [Hex] [
H e
x] D escrip
tio
n
EM 4723E PTO MODULE: PTO3 engagement 0D Special instructions Yellow
timeout
EM 4723F PTO MODULE: PTO3 disengagement 0D Special instructions Yellow
timeout
EM 47240 PTO MODULE: PTO3 unrequested 0D Special instructions Yellow
engagement
EM 47241 PTO MODULE: PTO3 unrequested 0D Special instructions Yellow
disengagement
Eurotronic 2 40302 Short circuit to ground at output stage to 05 Shorted to ground / low source Red
Y2
(Valve Splitter; DD: high, OD: low)
Eurotronic 2 40303 Short circuit to ground at output stage to 05 Shorted to ground / low source Red
Y3
(Valve Splitter; DD: low, OD: high)
Eurotronic 2 40304 Short circuit to ground at output stage to 05 Shorted to ground / low source Red
Y4
(Valve Select)
Eurotronic 2 40305 Short circuit to ground at output stage to 05 Shorted to ground / low source Red
Y5
(Valve Select)
Eurotronic 2 40306 Short circuit to ground at output stage to 05 Shorted to ground / low source Red
Y6
(Valve Shift)
Eurotronic 2 40307 Short circuit to ground at output stage to 05 Shorted to ground / low source Red
Y7
(Valve Shift)
Eurotronic 2 40308 Short circuit to ground at output stage to 05 Shorted to ground / low source Red
Y8
(Valve Range)
Eurotronic 2 40309 Short circuit to ground at output stage to 05 Shorted to ground / low source Red
Y9
(Valve Range)
Eurotronic 2 4030A Short circuit to ground at output stage to 05 Shorted to ground / low source Red
Y10
(Main valve)
Eurotronic 2 4030D Short circuit to ground at output stage to 00 No fault symptom available for this DTC Red
PTO 1
Eurotronic 2 4030E Short circuit to ground at output stage to 00 No fault symptom available for this DTC Red
PTO 2
Eurotronic 2 40311 Short circuit to ground at output stage to 05 Shorted to ground / low source Yellow
Y1
(inertia brake valve)
Eurotronic 2 40312 Short circuit to ground at output stage to 05 Shorted to ground / low source Yellow
small diseng. clutch valve
Eurotronic 2 40313 Short circuit to ground at output stage to 05 Shorted to ground / low source Yellow
small eng. clutch valve
Eurotronic 2 40314 Short circuit to ground at output stage to 05 Shorted to ground / low source Yellow
large diseng. clutch valve
Eurotronic 2 40315 Short circuit to ground at output stage to 05 Shorted to ground / low source Yellow
large eng. clutch valve
Eurotronic 2 40316 Short circuit to ground at output ADVP1 05 Shorted to ground / low source Red
or at ADVP (voltage supply to output
speed sensor 1)
Eurotronic 2 4031A CAN engine configuration timeout 04 No signal Yellow
Eurotronic 2 4031B Error on ”engine configuration message” 08 Invalid signal Yellow
(engine configuration)
Eurotronic 2 4031C Error on ”Actual driveline retarder - 08 Invalid signal Yellow
percent torque” signal (ERC1_DR)
Eurotronic 2 4031D Error on ”Engine coolant load increase” 08 Invalid signal Yellow
signal (ERC1_DR)
Eurotronic 2 4031E Error on ”Driveline retarder configuration 08 Invalid signal Yellow
message”
(Driveline retarder configuration)
Eurotronic 2 4031F Error on ”Actual engine retarder - 08 Invalid signal Yellow
percent torque” signal (ERC1_ER)
Eurotronic 2 40320 Error on ”Engine retarder configuration 08 Invalid signal Yellow
message”
(Engine retarder configuration)
Eurotronic 2 40321 CAN ”Engine retarder configuration” 04 No signal Yellow
timeout
Eurotronic 2 40322 Interruption at output stage to Y2 0A Disconnection Red
(Valve Splitter)
Eurotronic 2 40323 Interruption at output stage to Y3 0A Disconnection Red
(Valve Splitter)
Eurotronic 2 40324 Interruption at output stage to Y4 0A Disconnection Red
(Valve Select)
Eurotronic 2 40325 Interruption at output stage to Y5 0A Disconnection Red
(Valve Select)
Eurotronic 2 40326 Interruption at output stage to Y6 0A Disconnection Red
(Valve Shift)
Eurotronic 2 40327 Interruption at output stage to Y7 0A Disconnection Red
(Valve Shift)
Eurotronic 2 40328 Interruption at output stage to Y8 0A Disconnection Red
(Valve Range)
Eurotronic 2 40329 Interruption at output stage to Y9 0A Disconnection Red
(Valve Range)
Eurotronic 2 4032A Interruption at output stage to Y10 0A Disconnection Red
(Main valve)
Eurotronic 2 4032D Interruption at output stage to PTO 1 00 No fault symptom available for this DTC Yellow
Eurotronic 2 4032E Interruption at output stage to PTO 2 00 No fault symptom available for this DTC Yellow
Eurotronic 2 40331 Interruption at output stage to Y1 0A Disconnection Yellow
(inertia brake valve)
Eurotronic 2 40332 Interruption at output stage to small 0A Disconnection Yellow
disengagement clutch valve
Eurotronic 2 40333 Interruption at output stage to small 0A Disconnection Yellow
engagement clutch valve
Eurotronic 2 40334 Interruption at output stage to large 0A Disconnection Yellow
disengagement clutch valve
Eurotronic 2 40335 Interruption at output stage to large 0A Disconnection Yellow
engagement clutch valve
Eurotronic 2 40336 Interruption at output ADVP1 or at ADVP 0A Disconnection Red
(Power supply to output speed sensor 1)
Eurotronic 2 4033B Acknowledge fault of PTO 1 08 Invalid signal Yellow
Eurotronic 2 4033C Acknowledge fault of PTO 2 08 Invalid signal Yellow
Eurotronic 2 4033D Disengagement fault of PTO 1 08 Invalid signal Red
Eurotronic 2 4033E Disengagement fault of PTO 2 08 Invalid signal Red
Eurotronic 2 4033F Engagement fault of PTO1 08 Invalid signal Yellow
Eurotronic 2 40340 Engagement fault of PTO2 08 Invalid signal Yellow
Eurotronic 2 40342 Short circuit to positive at output stage to 06 Shorted to high source Red
Y2
(Valve Splitter)
Eurotronic 2 40343 Short circuit to positive at output stage to 06 Shorted to high source Red
Y3
(Valve Splitter)
Eurotronic 2 40344 Short circuit to positive at output stage to 06 Shorted to high source Red
Y4
(Valve Select)
Eurotronic 2 40345 Short circuit to positive at output stage to 06 Shorted to high source Red
Y5
(Valve Select)
Eurotronic 2 40346 Short circuit to positive at output stage to 06 Shorted to high source Red
Y6
(Valve Shift)
Eurotronic 2 40347 Short circuit to positive at output stage to 06 Shorted to high source Red
Y7
(Valve Shift)
Eurotronic 2 40348 Short circuit to positive at output stage to 06 Shorted to high source Red
Y8
(Valve range low)
Eurotronic 2 40349 Short circuit to positive at output stage to 06 Shorted to high source Red
Y9
(Valve range high)
Eurotronic 2 4034A Short circuit to positive at output stage to 06 Shorted to high source Yellow
Y10
(Main valve)
Eurotronic 2 4034D Short circuit to positive at output stage to 06 Shorted to high source Yellow
PTO 1
Eurotronic 2 4034E Short circuit to positive at output stage to 06 Shorted to high source Yellow
PTO 2
Eurotronic 2 40351 Short circuit to positive at output stage to 06 Shorted to high source Yellow
Y1
(inertia brake valve)
Eurotronic 2 40352 Short circuit to positive at output stage to 06 Shorted to high source Red
small diseng. clutch valve
Eurotronic 2 40353 Short circuit to positive at output stage to 06 Shorted to high source Red
small eng. clutch valve

Bianca Andreana Trakker E4 Errors list Print Date: 21.11.2021

ELTRAC ET-TN-445-87 - Trakker E4 Error Codes Page 19 of 30

E C U S P
N Fa u ltCo m po ne n t D
es
crip
tio
n F MI FM I C
omm
en
t L
amps
tat
u s M
ILL
amp
N a me [
H e
x] [
H e
x] De scriptio
n
Eurotronic 2 40354 Short circuit to positive at output stage to 06 Shorted to high source Red
large diseng. clutch valve
Eurotronic 2 40355 Short circuit to positive at output stage to 06 Shorted to high source Red
large eng. clutch valve
Eurotronic 2 40356 Short circuit to positive at output ADVP1 06 Shorted to high source Yellow
or at ADVP (voltage supply to display to
output speed sensor 1)
Eurotronic 2 4035A Communication error between controller 09 Device error Red
1 and controller 2
(ECU failure)
Eurotronic 2 4035B CAN EBC1 timeout 04 No signal Yellow
Eurotronic 2 4035C Error on ”ABS active” signal (EBC1) 08 Invalid signal Yellow
Eurotronic 2 4035D Error on ”ASR engine control active” 08 Invalid signal Yellow
signal (EBC1)
Eurotronic 2 4035E Error on ”ASR brake control active” 08 Invalid signal Yellow
signal (EBC1)
Eurotronic 2 4035F Error on ”Cruise control active” signal 08 Invalid signal Yellow
(CCVS)
Eurotronic 2 40360 Error on ”Cruise control set speed” 08 Invalid signal Yellow
(CCVS)
Eurotronic 2 40361 Error on ”Engine speed” signal (EEC1) 08 Invalid signal Yellow
Eurotronic 2 40362 Error on transmission input speed signal 08 Invalid signal Yellow
Eurotronic 2 40363 Error on output speed signal 1 08 Invalid signal Yellow
Eurotronic 2 40364 Error on CAN output speed signal 2 08 Invalid signal Yellow
Eurotronic 2 40365 Error on both output speed signals 08 Invalid signal Red
Eurotronic 2 40366 Plausibility error between transmission 03 Not plausible Yellow
input speed and output speed
Eurotronic 2 40367 CAN CCVS error on wheel based 00 No fault symptom available for this DTC Yellow
vehicle speed
Eurotronic 2 40368 High voltage (Vehicle electrical system 01 Above maximum threshold Yellow
voltage too high)
Eurotronic 2 40369 Low voltage (Vehicle electrical system 02 Below minimum threshold Red
voltage too low)
Eurotronic 2 4036B Stabilised voltage supply at output AU 02 Below minimum threshold Yellow
(clutch sensor supply)
out of valid range
Eurotronic 2 4036C Error in selector lever or tip lever 00 No fault symptom available for this DTC Yellow
Eurotronic 2 4036E Lever CAN timeout 00 No fault symptom available for this DTC Yellow
Eurotronic 2 40371 CAN message "Driveline retarder 04 No signal Yellow
configuration" timeout
Eurotronic 2 40372 Clutch engaged unintentionally in 00 No fault symptom available for this DTC Red
standstill, gear engaged
Eurotronic 2 40375 Error in clutch self-adjustment process 00 No fault symptom available for this DTC Red
Eurotronic 2 40376 Clutch does not disengage 00 No fault symptom available for this DTC Red
Eurotronic 2 40377 Clutch does not engage / does not 00 No fault symptom available for this DTC Red
transmit engine torque
Eurotronic 2 40378 Mechanical failure of small 00 No fault symptom available for this DTC Yellow
disengagement clutch valve
Eurotronic 2 40379 Mechanical failure of large 00 No fault symptom available for this DTC Yellow
disengagement clutch valve
Eurotronic 2 4037A Mechanical failure of small engagement 00 No fault symptom available for this DTC Yellow
clutch valve
Eurotronic 2 4037B Mechanical failure of large engagement 00 No fault symptom available for this DTC Yellow
clutch valve
Eurotronic 2 4037C Error on clutch travel signal 00 No fault symptom available for this DTC Yellow
Eurotronic 2 4037E Error on pressure sensor signal 03 Not plausible Yellow
Eurotronic 2 4037F Error on ECU temperature sensor signal 03 Not plausible Yellow
Eurotronic 2 40380 Error on oil temperature sensor signal 00 No fault symptom available for this DTC Yellow
Eurotronic 2 40381 No shift sensor signal (Short circuit to 06 Shorted to high source Yellow
positive)
Eurotronic 2 40382 No shift sensor signal (Short circuit to 05 Shorted to ground / low source Yellow
ground)
Eurotronic 2 40383 No shift sensor signal (Interruption) 0A Disconnection Yellow
Eurotronic 2 40384 Self adjustment error of shift sensor 00 No fault symptom available for this DTC Red
Eurotronic 2 40385 No gate select sensor signal (Short 06 Shorted to high source Yellow
circuit to positive)
Eurotronic 2 40386 No gate select sensor signal (Short 05 Shorted to ground / low source Yellow
circuit to ground)
Eurotronic 2 40387 No gate select sensor signal 0A Disconnection Yellow
(Interruption)
Eurotronic 2 40388 Gate select sensor self adjustment error 00 No fault symptom available for this DTC Red
Eurotronic 2 40389 No range change group (GP) sensor 06 Shorted to high source Yellow
signal (Short circuit to positive)
Eurotronic 2 4038A No range change group (GP) sensor 05 Shorted to ground / low source Yellow
signal (Short circuit to ground)
Eurotronic 2 4038B No range change group (GP) sensor 0A Disconnection Yellow
signal (Interruption)
Eurotronic 2 4038C Self adjustment error of range change 00 No fault symptom available for this DTC Red
group sensor in position fast
Eurotronic 2 4038D No splitter group (GV) sensor signal 06 Shorted to high source Yellow
(Short circuit to positive)
Eurotronic 2 4038E No splitter group (GV) sensor signal 05 Shorted to ground / low source Yellow
(Short circuit to ground)
Eurotronic 2 4038F No splitter group (GV) sensor signal 0A Disconnection Yellow
(Interruption)
Eurotronic 2 40390 Splitter group (GV) sensor self 00 No fault symptom available for this DTC Red
adjustment error
Eurotronic 2 40391 Range change group (GP) 00 No fault symptom available for this DTC Yellow
disengagement error
Eurotronic 2 40392 Changeover error during range change 00 No fault symptom available for this DTC Yellow
group (GP) shifting
Eurotronic 2 40393 Range change group (GP) does not 00 No fault symptom available for this DTC Red
engage
Eurotronic 2 40394 Splitter (GV) does not disengage 00 No fault symptom available for this DTC Yellow
Eurotronic 2 40395 Change over error during splitter shifting 00 No fault symptom available for this DTC Yellow
Eurotronic 2 40396 Splitter (GV) does not engage 00 No fault symptom available for this DTC Red
Eurotronic 2 40397 Selector cylinder does not disengage 00 No fault symptom available for this DTC Yellow
Eurotronic 2 40398 Change over error during gate selection 00 No fault symptom available for this DTC Yellow
procedure
Eurotronic 2 40399 Selector cylinder does not engage 00 No fault symptom available for this DTC Red
Eurotronic 2 4039A Main transmission gear does not 00 No fault symptom available for this DTC Red
disengage
Eurotronic 2 4039B Main transmission gear does not engage 00 No fault symptom available for this DTC Red
Eurotronic 2 4039C Wrong gear shifting 00 No fault symptom available for this DTC Red
Eurotronic 2 4039D Selector sensor signal leaves engaged 00 No fault symptom available for this DTC Yellow
position during driving
Eurotronic 2 4039E Shift sensor signal leaves engaged 00 No fault symptom available for this DTC Yellow
position during driving
Eurotronic 2 4039F Range-change group sensor signal 00 No fault symptom available for this DTC Yellow
leaves engaged position during driving
Eurotronic 2 403A0 Splitter sensor signal leaves engaged 00 No fault symptom available for this DTC Yellow
position during driving
Eurotronic 2 403A3 Engine does not react on torque 00 No fault symptom available for this DTC Yellow
intervention
Eurotronic 2 403A4 Error on ”Drivers demand engine 08 Invalid signal Yellow
percent torque” (EEC1)
Eurotronic 2 403A5 Error on ”Accelerator pedal position” 08 Invalid signal Yellow
(EEC2)
Eurotronic 2 403A6 Permanent idle signal 00 No fault symptom available for this DTC Yellow
Eurotronic 2 403A8 No idle signal or error on ”idle signal 08 Invalid signal Yellow
switch” signal (EEC2) or never active
"idle signal"
Eurotronic 2 403A9 Cut-off relay in ECU does not switch off 00 No fault symptom available for this DTC Red
Eurotronic 2 403AA No voltage supply at key 30 or cut-off 00 No fault symptom available for this DTC Red
relay in ECU does not switch on
Eurotronic 2 403AB Error on ”Actual engine percent torque” 08 Invalid signal Yellow
signal (EEC1)
Eurotronic 2 403AE Error on ”Kickdown switch” signal 08 Invalid signal Yellow
(EEC2)
Eurotronic 2 403AF Error on ”Ignition lock” signal (terminal 04 No signal Yellow
15)
Eurotronic 2 403B1 System-CAN Busoff error 04 No signal Red
Eurotronic 2 403B2 CAN Error warning 04 No signal Red
Eurotronic 2 403B3 CAN queue overrun 00 No fault symptom available for this DTC Red
Eurotronic 2 403B4 CAN EEC1 timeout 04 No signal Red
Eurotronic 2 403B5 CAN EEC2 timeout 04 No signal Red
Eurotronic 2 403B6 CAN CCVS timeout 04 No signal Yellow
Eurotronic 2 403B7 CAN ERC1_ER timeout 04 No signal Yellow
Eurotronic 2 403B8 CAN ERC1_DR timeout 04 No signal Yellow
Eurotronic 2 403BC ECU fault - wrong interrupt 00 No fault symptom available for this DTC Red
Eurotronic 2 403BD ECU fault - stack watch 00 No fault symptom available for this DTC Red
Eurotronic 2 403BE EOL EEPROM parameter out of valid 00 No fault symptom available for this DTC Red
range
Eurotronic 2 403BF EOL EEPROM parameter checksum 00 No fault symptom available for this DTC Red
error
Eurotronic 2 403C0 ECU fault - EEPROM access failure 00 No fault symptom available for this DTC Yellow
Eurotronic 2 403C1 ECU temperature too high 01 Above maximum threshold Red

Bianca Andreana Trakker E4 Errors list Print Date: 21.11.2021

ELTRAC ET-TN-445-87 - Trakker E4 Error Codes Page 20 of 30

E C U SPN F aultC o m po nen t D

es
crip
tio
n F MI FM I C
omm
en
t L
amps
tat
u s M
ILL
amp
N a me [Hex] [
H e
x] D escription
Eurotronic 2 403C2 Both sources for front axle speed not 00 No fault symptom available for this DTC Yellow
available
Eurotronic 2 403C5 Error on "Front axle speed" (EBC2) 08 Invalid signal Yellow
Eurotronic 2 403C7 CAN EBC2 timeout 04 No signal Yellow
Eurotronic 2 403E2 IVECO:CAN message BC_TC timeout 00 No fault symptom available for this DTC Red
Eurotronic 2 403E3 Application-Error database for 00 No fault symptom available for this DTC Red
CAN-communication
Eurotronic 2 403E7 CAN EEC3 timeout 00 No fault symptom available for this DTC Red
Eurotronic 2 403F1 IVECO: CAN VCM_TC timeout 00 No fault symptom available for this DTC Red
Eurotronic 2 403F6 CAN PTI timeout 00 No fault symptom available for this DTC Red
Eurotronic 2 403FD IVECO: CAN EM_CMD timeout 00 No fault symptom available for this DTC Red
IBC3 22100 ECU not programmed 1F Yellow
IBC3 22101 EEPROM checksum error 0C Yellow
IBC3 22102 ECU Overheating The PCB ECU Temperature of the output drivers is greater 0C Yellow
than max. allowed temperature (100°C).
IBC3 22103 ECU Secondary Microprocessor Faulty The secondary microprocessor that executes the limp-home 0C Yellow
function is faulty
IBC3 2210B Vehicle Data Bus CAN No CAN messages on Vehicle data bus or Bus-Off detection. 02 Red
The error can be read on VDB CAN only if the VDB CAN bus
resets
IBC3 2210C Body Control Bus CAN No CAN messages on Body control bus or Bus-Off detection. 02 Red
The error can be read on BCB CAN also if the BCB CAN bus
is not reset
IBC3 231FF Body Control Bus - ECU#1 CAN No CAN messages from ECU#1 - Bed Module 02 Yellow
IBC3 2ECFF Body Control Bus - ECU#2 CAN No CAN messages from ECU#2 - Driver Door Module 02 Yellow
IBC3 2EDFF Body Control Bus - ECU#3 CAN No CAN messages from ECU#3 - Co-Driver Door Module 02 Yellow
IBC3 245FF Body Control Bus - ECU#4 CAN No CAN messages from ECU#4 - Additional Heater Air 02 Yellow
IBC3 244FF Body Control Bus - ECU#5 CAN No CAN messages from ECU#5 - Additional Heater Water 02 Yellow
IBC3 2E9FF Body Control Bus - ECU#6 CAN No CAN messages from ECU#6 - Mirror Controller 02 Yellow
IBC3 26DFF Body Control Bus - ECU#7 CAN No CAN messages from ECU#7 - MET 02 Red
IBC3 219FF Body Control Bus - ECU#8 CAN No CAN messages from ECU#8 - Climate Control 02 Yellow
IBC3 22120 Fuel Level Interface Fuel Level interface failure detected. 00 Resistance above normal Yellow
The input voltage is evaluated for in-range checking:
IBC3 22121 Engine Oil Level Interface Oil Level interface failure detected. 00 Delta voltage below normal Yellow
The voltage difference between the first and the second
acquisition are evaluated for in-range checking:
IBC3 22121 Engine Oil Level Interface 01 Delta voltage above normal Yellow
IBC3 22121 Engine Oil Level Interface 0F Time/Date from TCO not available Yellow
IBC3 22121 Engine Oil Level Interface 10 EEC1 message from EDC not available Yellow
IBC3 22121 Engine Oil Level Interface 12 Date could not be stored in EEPROM Yellow
IBC3 22121 Engine Oil Level Interface 13 Time could not be stored in EEPROM Yellow
IBC3 22121 Engine Oil Level Interface 14 Oil Level could not be stored in Yellow
EEPROM
IBC3 22122 Ambient Air Temperature Interface Ambient Air Temperature interface failure detected. 03 Voltage above normal (s.c. to battery or Yellow
The input voltage is evaluated for in-range checking: open circuit)
IBC3 22122 Ambient Air Temperature Interface 04 Voltage below normal (s.c. to ground) Yellow
IBC3 22130 Windshield Wiper Switches Windshield Wiper switches activated at the same time or every 02 Yellow
faulty on Windshield Wiper (engine blocked or short circuited,
engine interrupted, cam always to ground, cam always open)
IBC3 22131 Diff.Lock.State. Rear Axle1(Rockwell) Diff.Lock.State. Rear Axle1-In1 and Diff. Lock State Rear 02 Yellow
Switches Axle1-In2, are both activated
IBC3 22140 Service Brake Air Pressure Circuit#2 Service Brake Air Pressure Circuit#2 interface failure detected. 03 Voltage above normal (s.c. to battery or Yellow
sensor (Front) open circuit)
IBC3 22140 Service Brake Air Pressure Circuit#2 04 Voltage below normal (s.c. to ground) Yellow
sensor (Front)
IBC3 22141 Service Brake Air Pressure Circuit#1 Service Brake Air Pressure Circuit#1 interface failure detected. 03 Voltage above normal (s.c. to battery or Yellow
sensor (Rear) open circuit)
IBC3 22141 Service Brake Air Pressure Circuit#1 04 Voltage below normal (s.c. to ground) Yellow
sensor (Rear)
IBC3 22142 Service Brake Air Pressure Circuit#2 The pressure charging is evaluated for in-range checking 00 Pressure above normal: Red
sensor (Front) Service Brake Air Pressure Circuit #2 ≥
BAP_PRS_ MAX
IBC3 22142 Service Brake Air Pressure Circuit#2 01 Pressure below normal: Red
sensor (Front) After BAP_TEST_T engine is running
(Engine
Speed>BAP_ENG_SPEED_MIN)
Service Brake Air Pressure Circuit #2 ≤
BAP_PRS_ MIN
IBC3 22143 Service Brake Air Pressure Circuit#1 The pressure charging is evaluated for in-range checking 00 Pressure above normal: Red
sensor (Rear) Service Brake Air Pressure Circuit #1 ≥
BAP_PRS_ MAX
IBC3 22143 Service Brake Air Pressure Circuit#1 01 Pressure below normal: Red
sensor (Rear) After BAP_TEST_T engine is running
(Engine
Speed>BAP_ENG_SPEED_MIN)
Service Brake Air Pressure Circuit #1 ≤
BAP_PRS_ MIN
IBC3 22144 Service Brake Air Pressure Sensor Service Brake Air Pressure Sensor Supply Voltage failure 00 6V<V<8V Yellow
Supply Voltage (Vs) detected.
The error is detected only when the maximum supply voltage
is between 18V and 32V and Ignition Key 15 is On.
IBC3 22144 Service Brake Air Pressure Sensor 01 2V<V<4V Yellow
Supply Voltage (Vs)
IBC3 22144 Service Brake Air Pressure Sensor 03 V>8V Yellow
Supply Voltage (Vs)
IBC3 22144 Service Brake Air Pressure Sensor 04 V<2V Yellow
Supply Voltage (Vs)
IBC3 22145 Brake Air (S-APU) Pressure plausability: 01 The pressure is not increasing while Yellow
charge mode
IBC3 22145 Brake Air (S-APU) 00 The pressure is not decreasing while Yellow
rigeneration mode
IBC3 22145 Brake Air (S-APU) 02 Duty error (air loss because the S2 Yellow
valve is locked)
IBC3 22150 Dashboard Backlight & Body Builders On/Off Diagnostic 06 Short circuit to ground or Overload or Yellow
Parking Lights Overheating protection.
IBC3 22161 Marker Front Left & Right Lights This fault shall be recognized, stored and reported on DM1 05 The acquired load current is below a Yellow
message with a 10sec delay. (battery voltage dependent) threshold.
At least a load (out of two) is in open
circuit.
IBC3 22161 Marker Front Left & Right Lights 06 Short circuit to ground or Overload or Yellow
Overheating protection (tested in On
state).
IBC3 22163 Step Lights This fault shall be recognized, stored and reported on DM1 05 The acquired load current is below a Yellow
message with a 10sec delay. (battery voltage dependent) threshold.
At least a load (out of two) is in open
circuit.
IBC3 22163 Step Lights 06 Short circuit to ground or Overload or Yellow
Overheating protection (tested in On
state).
IBC3 22164 Cabin Side Lights On/Off Diagnostic 03 Short circuit to battery (test with driver Yellow
OFF)
IBC3 22164 Cabin Side Lights 06 Short circuit to ground or Overload or Yellow
Overheating protection (test with driver
ON).
IBC3 22165 Cabin Ceiling Lights This fault shall be recognized, stored and reported on DM1 05 The acquired load current is below a Yellow
message with a 10sec delay. (battery voltage dependent) threshold.
At least a load (out of two) is in open
circuit.
IBC3 22165 Cabin Ceiling Lights 06 Short circuit to ground or Overload or Yellow
Overheating protection (tested in On
state).
IBC3 22166 Additional Lights On/Off Diagnostic on the output (connectyed to a relay) 03 Short circuit to battery (test with driver Yellow
OFF)
IBC3 22166 Additional Lights 06 Short circuit to ground or Overload or Yellow
Overheating protection (test with driver
ON).
IBC3 22167 Reverse Gear Lights On/Off Diagnostic on the output (connectyed to a relay) 03 Short circuit to battery (test with driver Yellow
OFF)
IBC3 22167 Additional Lights or Additional Air Heater 06 Short circuit to ground or Overload or Yellow
Disable Overheating protection (test with driver
ON).
IBC3 22180 30A On/Off Diagnostic 04 Voltage below normal Yellow
IBC3 22181 30B On/Off Diagnostic 04 Voltage below normal Yellow
IBC3 22182 30C On/Off Diagnostic 04 Voltage below normal Yellow
IBC3 22183 30D On/Off Diagnostic 04 Voltage below normal Yellow
IBC3 22184 30E On/Off Diagnostic 04 Voltage below normal Yellow
IBC3 22190 A15/A16 output : +Batt TCO & +Batt. IC. On/Off Diagnostic: 05 fuse interrupped Yellow
& +Batt. Bed Module The internal fuse to ECU can be accidentally interrupted
IBC3 22191 F1 output: 30A Brake Switch On/Off Diagnostic: 05 fuse interrupped Yellow
The internal fuse to ECU can be accidentally interrupted
IBC3 22192 B9 output: 30D Body Builders On/Off Diagnostic: 05 fuse interrupped Yellow
The internal fuse to ECU can be accidentally interrupted
IBC3 22193 B4 output: 30E ECAS On/Off Diagnostic: 05 fuse interrupped Yellow
The internal fuse to ECU can be accidentally interrupted
IBC3 22194 A6 output: 30C VCM On/Off Diagnostic: 05 fuse interrupped Yellow
The internal fuse to ECU can be accidentally interrupted

Bianca Andreana Trakker E4 Errors list Print Date: 21.11.2021

ELTRAC ET-TN-445-87 - Trakker E4 Error Codes Page 21 of 30

E CU SPN FaultC om p on ent D

es
crip
tio
n F MI FM I C
omm
en
t L
amps
tat
u s M
ILL
amp
Name [Hex] [
H e
x] De s
crip
tio
n
IBC3 22195 B3 output: 30E Cigarette Lighter & 30E On/Off Diagnostic: 05 fuse interrupped Yellow
Diagnostic Connector The internal fuse to ECU can be accidentally interrupted
IBC3 22196 A4 output: 30C ABS On/Off Diagnostic: 05 fuse interrupped Yellow
The internal fuse to ECU can be accidentally interrupted
IBC3 22197 A3 output: 30C ABS Trailer On/Off Diagnostic: 05 fuse interrupped Yellow
The internal fuse to ECU can be accidentally interrupted
IBC3 22198 A13 output: 30B Engine Crank On/Off Diagnostic: 05 fuse interrupped Yellow
The internal fuse to ECU can be accidentally interrupted
IBC3 22199 B17 output: 30D Acoustic Horn On/Off Diagnostic: 05 fuse interrupped Yellow
The internal fuse to ECU can be accidentally interrupted
IBC3 2219A B6 output: 30E Voltage Adapter On/Off Diagnostic: 05 fuse interrupped Yellow
The internal fuse to ECU can be accidentally interrupted
IBC3 2219B A1 output: 30B Mirror Heating On/Off Diagnostic: 05 fuse interrupped Yellow
The internal fuse to ECU can be accidentally interrupted
IBC3 221A0 B15/B16 output: 15 Mirror Controller & On/Off Diagnostic: 05 fuse interrupped Yellow
15 Heated Dryer The internal fuse to ECU can be accidentally interrupted
IBC3 221A1 C2 output: 15 Alternator On/Off Diagnostic: 05 fuse interrupped Yellow
The internal fuse to ECU can be accidentally interrupted
IBC3 221A2 E13 output: 15 TCO & 15 Cluster & 15 On/Off Diagnostic: 05 fuse interrupped Yellow
MET & 15 UDS The internal fuse to ECU can be accidentally interrupted
IBC3 221A3 E10 output: 15 VCM & 15 ECM On/Off Diagnostic: 05 fuse interrupped Yellow
The internal fuse to ECU can be accidentally interrupted
IBC3 221A4 E12/E11 output: 15 ECAS & 15 ABS On/Off Diagnostic: 05 fuse interrupped Yellow
The internal fuse to ECU can be accidentally interrupted
IBC3 221A5 E8/F18 output: 15 Cabin Tilted & 15 On/Off Diagnostic: 05 fuse interrupped Yellow
Headbeam Pot. Supply The internal fuse to ECU can be accidentally interrupted
IBC3 221A6 A9 output: 15/1A Reverse Gear Lights & On/Off Diagnostic: 05 fuse interrupped Yellow
15/1A Headbeam Adjustment supply The internal fuse to ECU can be accidentally interrupted
IBC3 221A7 A17 output:15/1A Cabin Heater & 15/1A On/Off Diagnostic: 05 fuse interrupped Yellow
Conditioner The internal fuse to ECU can be accidentally interrupted
IBC3 221A8 B1 output : 15/1B Body Builders On/Off Diagnostic: 05 fuse interrupped Yellow
The internal fuse to ECU can be accidentally interrupted
IBC3 221A9 B13 output: 15/1B Electric Windows On/Off Diagnostic: 05 fuse interrupped Yellow
The internal fuse to ECU can be accidentally interrupted
IBC3 221B0 Power Steering Circuit #1 or #2 Sensor plausibility: 02 Sensor plausibility Yellow
Pressure Low - While Engine Speed=0 (and valid) at least one of two
pressure switches is in Normal state (open) (pressure above
threshold)
The ECU waits PSC_TEST_T1 (after Engine Speed =0 or at
Ignition Key 15) before to start the diagnostics
IBC3 221B2 Steering Flow Meter Flow meter plausibility: 02 Flow meter plausibility Yellow
- When Vehicle Speed < PSC_VEH_SPEED _MIN the flow is
in Normal state (open)
IBC3 221C0 Windshield Washer On/Off Diagnostic 03 Short circuit to battery (test with driver Yellow
OFF)
IBC3 221C0 Windshield Washer 06 Short circuit to ground or Overload or Yellow
Overheating protection (test with driver
ON).
IBC3 221C1 TGC ON On/Off Diagnostic 03 Short circuit to battery (test with driver Yellow
OFF)
IBC3 221C1 TGC ON 06 Short circuit to ground or Overload or Yellow
Overheating protection (test with driver
ON).
IBC3 221C2 TGC OFF On/Off Diagnostic 03 Short circuit to battery (test with driver Yellow
OFF)
IBC3 221C3 Body Builder Reverse Gear On/Off Diagnostic 03 Short circuit to battery (test with driver Yellow
OFF)
IBC3 221C3 Body Builder Reverse Gear 06 Short circuit to ground or Overload or Yellow
Overheating protection (test with driver
ON).
IBC3 221C4 Vehicle Running On/Off Diagnostic 03 Short circuit to battery (test with driver Yellow
OFF)
IBC3 221C4 Vehicle Running 06 Short circuit to ground or Overload or Yellow
Overheating protection (test with driver
ON).
IBC3 221C5 Engine Running On/Off Diagnostic 03 Short circuit to battery (test with driver Yellow
OFF)
IBC3 221C5 Engine Running 06 Short circuit to ground or Overload or Yellow
Overheating protection (test with driver
ON).
IBC3 221C6 Roof Hatch open On/Off Diagnostic 03 Short circuit to battery (test with driver Yellow
OFF)
IBC3 221C6 Roof Hatch open 06 Short circuit to ground or Overload or Yellow
Overheating protection (test with driver
ON).
IBC3 221C7 Roof Hatch close On/Off Diagnostic 03 Short circuit to battery (test with driver Yellow
OFF)
IBC3 221C7 Roof Hatch closeù 06 Short circuit to ground or Overload or Yellow
Overheating protection (test with driver
ON).
IBC3 221C8 Headlights Washer On/Off Diagnostic 03 Short circuit to battery (test with driver Yellow
OFF)
IBC3 221C8 Headlights Washer 06 Short circuit to ground or Overload or Yellow
Overheating protection (test with driver
ON).
IBC3 221C9 Additional Air Heater Disable On/Off Diagnostic on the output (connectyed to a relay) 03 Short circuit to battery (test with driver Yellow
OFF)
IBC3 221C9 Additional Air Heater Disable 06 Short circuit to ground or Overload or Yellow
Overheating protection (test with driver
ON).
IC M06 41701 EEPROM checksum Physical memory fault.Checksum failure is detected 0C Yellow
IC M06 41702 Ignition Key (15) fault Signal not plausible with Ignition Key (15) over CAN 0B Yellow
IC M06 41703 Ignition Key (15) over CAN fault Signal not plausible with Ignition Key (15) 02 Yellow
IC M06 41704 Stepper Motor Defect, access not possible.Stepper motor failure is present. 0C Yellow
IC M06 41705 Reserved for: Yellow
Fuel Level Sensor
IC M06 41706 Reserved for: Yellow
Oil Level Sensor
IC M06 41707 Reserved for: Yellow
Ambient Temperature Sensor
IC M06 41708 Reserved for: A fault of the Indicator Lamp or on its driving circuitry is Yellow
OBD II Indicator Lamp (IL25) detected...
IC M06 41709 - 0C Yellow
IC M06 4170A - 0C Yellow
IC M06 4170B Reserved for: No CAN messages on CAN 2 or bus-off detection 02 Red
CAN 2 Bus
IC M06 4170C Vehicle Data Bus CAN No CAN messages on Vehicle Data Bus or bus-off detection 02 Red
IC M06 4170D Vehicle Data Bus - ECU#1 CAN No CAN messages from ECU#1 - BC 02 Red
IC M06 4170E Vehicle Data Bus - ECU#2 CAN No CAN messages from ECU#2 - EDC or VCM 02 Red
IC M06 4170F Vehicle Data Bus - ECU#3 CAN No CAN messages from ECU#3 - TCO 02 Red
IC M06 41710 Vehicle Data Bus - ECU#4 CAN No CAN messages from ECU#4 - ETC 02 Red
IC M06 41711 Vehicle Data Bus - ECU#5 CAN No CAN messages from ECU#5 - EBC 02 ABS Yellow
tell tale
IC M06 41712 Vehicle Data Bus - ECU#6 CAN No CAN messages from ECU#6 - ECAS 02 Yellow
IC M06 41713 Vehicle Data Bus - ECU#7 CAN No CAN messages from ECU#7 - Driveline Retarder 02 Yellow
IC M06 41714 Vehicle Data Bus - ECU#8 CAN No CAN messages from ECU#8 - Mirror Controller 02 Yellow
IC M06 41715 Vehicle Data Bus - ECU#9 CAN No CAN messages from ECU#9 - Expansion Module 02 Yellow
IC M06 41716 Vehicle Data Bus - ECU#10 CAN No CAN messages from ECU#10 - Steering Wheel Interface 02 Yellow
IC M06 41717 Vehicle Data Bus - ECU#11 CAN No CAN messages from ECU#11 - IVTM 02 Yellow
IC M06 41701 EEPROM checksum Physical memory fault.Checksum failure is detected 0C Yellow
MY08
IC M06 41702 Ignition Key (15) fault Signal not plausible with Ignition Key (15) over CAN 0B Yellow
MY08
IC M06 41703 Ignition Key (15) over CAN fault Signal not plausible with Ignition Key (15) 02 Yellow
MY08
IC M06 41704 Stepper Motor Defect, access not possible.Stepper motor failure is present. 0C Yellow
MY08
IC M06 41705 Reserved for: Yellow
MY08 Fuel Level Sensor
IC M06 41706 Reserved for: Yellow
MY08 Oil Level Sensor
IC M06 41707 Reserved for: Yellow
MY08 Ambient Temperature Sensor
IC M06 41708 Reserved for: A fault of the Indicator Lamp or on its driving circuitry is Yellow
MY08 OBD II Indicator Lamp (IL25) detected...
IC M06 41709 0C Yellow
MY08
IC M06 4170A 0C Yellow
MY08
IC M06 4170B Reserved for: No CAN messages on CAN 2 or bus-off detection 02 Red
MY08 CAN 2 Bus
IC M06 4170C Vehicle Data Bus CAN No CAN messages on Vehicle Data Bus or bus-off detection 02 Red
MY08
IC M06 4170D Vehicle Data Bus - ECU#1 CAN No CAN messages from ECU#1 - BC 02 Red
MY08
IC M06 4170E Vehicle Data Bus - ECU#2 CAN No CAN messages from ECU#2 - EDC or VCM 02 Red
MY08

Bianca Andreana Trakker E4 Errors list Print Date: 21.11.2021

ELTRAC ET-TN-445-87 - Trakker E4 Error Codes Page 22 of 30

EC U SPN F aultC o mponent D

es
crip
tio
n F MI F
M I C
omm
en
t L
amps
tat
u s M
ILL
amp
N am e [Hex] [
H e
x] D
es
crip
tio
n
IC M06 4170F Vehicle Data Bus - ECU#3 CAN No CAN messages from ECU#3 - TCO 02 Red
MY08
IC M06 41710 Vehicle Data Bus - ECU#4 CAN No CAN messages from ECU#4 - ETC 02 Red
MY08
IC M06 41711 Vehicle Data Bus - ECU#5 CAN No CAN messages from ECU#5 - EBC 02 ABS Yellow
MY08 tell tale
IC M06 41712 Vehicle Data Bus - ECU#6 CAN No CAN messages from ECU#6 - ECAS 02 Yellow
MY08
IC M06 41713 Vehicle Data Bus - ECU#7 CAN No CAN messages from ECU#7 - Driveline Retarder 02 Yellow
MY08
IC M06 41714 Vehicle Data Bus - ECU#8 CAN No CAN messages from ECU#8 - Mirror Controller 02 Yellow
MY08
IC M06 41715 Vehicle Data Bus - ECU#9 CAN No CAN messages from ECU#9 - Expansion Module 02 Yellow
MY08
IC M06 41716 Vehicle Data Bus - ECU#10 CAN No CAN messages from ECU#10 - Steering Wheel Interface 02 Yellow
MY08
IC M06 41717 Vehicle Data Bus - ECU#11 CAN No CAN messages from ECU#11 - IVTM 02 Yellow
MY08
IC M06 41718 Vehicle Data Bus - ECU#12 CAN No CAN messages from ECU#11 - ADM 02 Yellow
MY08
Intarder 41001 Short-circuit to ground on "accumulator 05 Shorted to ground / low source Detected by hardware, after key on Yellow
charge valve" output (AD1) or if output is activated
Intarder 41002 Short-circuit to positive on "accumulator 06 Shorted to high source Detected by hardware, after key on Yellow
charge valve" output (AD1) or if output is not activated
Intarder 41003 Interrupt on "accumulator charge valve" 0A Disconnection Detected by hardware, after key on Yellow
output (AD1) or if output is not activated
Intarder 41019 Short-circuit to ground on "proportional 05 Shorted to ground / low source Detected by hardware, after key on Yellow
valve" output (AIP) or if current>50 mA bei proportional
magnet is not activated
Intarder 4101A Short-circuit to positive on "proportional 06 Shorted to high source Always detected Yellow
valve" output (AIP)
Intarder 4101B Interrupt on "proportional valve" output 0A Disconnection Always detected Yellow
(AIP)
Intarder 4101C Resistance error on "proportional valve" 09 Device error Detected by hardware, if current>50 Yellow
output (AIP) mA bei proportional valve is not
activated
Intarder 4101D Short-circuit to ground on "proportional 05 Shorted to low source Detected by hardware, after key on Yellow
valve ground feedback" output (ADM1)
Intarder 4101E Short-circuit to positive on "proportional 06 Shorted to high source Always detected Yellow
valve ground feedback" output (ADM1)
Intarder 41022 Speed sensor failure on output shaft 04 No signal Detected by plausibility check with Yellow
(interruption) moving vehicle (> 20 km/h)
Intarder 41025 Temperature sensor interrupt or short 0A Disconnection Always detected Yellow
circuit to plus
Intarder 41026 Temperature sensor short circuit to 07 General short: Always detected Yellow
ground
Intarder 41027 Below minimum threshold of readback 02 Below min. Threshold Always detected Yellow
current on "proportional valve" output
Intarder 41028 Above maximum threshold of readback 01 Above maximum threshold Always detected Yellow
current on "proportional valve" output
Intarder 41029 Interruption at key 30 0A Disconnection Detected when key 15 > 16 V Yellow
Intarder 4102A Key 15 overvoltage 01 Above maximum threshold Always detected (> 36 V) Yellow
Intarder 4102B Key 15 undervoltage 02 Below min. threshold Detected (< 17 V) when engine is Yellow
running (> 450 rpm)
Intarder 4102C Faulty "Braking level selector" 03 Not plausible Detected by plausibility check Yellow
information via CAN BC_DR message
Intarder 4102D End-of-line parameter not valid 00 No fault symptom Detected after key on Yellow
Intarder 4102E "Operating hours counter" loss 00 No fault symptom Detected by plausibility check after Yellow
key on
Intarder 4102F "Error memory" loss 00 No fault symptom Detected by plausibility check after Yellow
key on
Intarder 41031 CAN-message EEC2 failure 04 No signal CAN message timeout or faulty Yellow
signal (acc. pedal low idle switch,
acc. pedal position)
Intarder 41033 System error of ECU 00 No fault symptom Always detected Yellow
Intarder 41034 CAN-message TSC1_AD failure 04 No signal CAN message timeout or faulty Yellow
signal
Intarder 41035 CAN transmit error 00 No fault symptom Always detected (queue overrun) Yellow
Intarder 41036 CAN-BusOff 09 Device error Always detected (CAN-controller Yellow
BusOff flag)
Intarder 41038 CAN-Acknowledge Error 00 No fault symptom Always detected (CAN-controller Yellow
Errror-Warning flag)
Intarder 41039 CAN-message EEC1 failure 04 No signal CAN message timeout or faulty Yellow
signal (engine speed, actual/driver's
demand engine percent torque)
Intarder 4103A CAN-message TCO1 failure 04 No signal CAN message timeout or faulty Yellow
signal (Tachograph output shaft
speed), at Ecosplit without transfer
box
Intarder 4103E CAN-message CCVS failure 04 No signal CAN message timeout or faulty Yellow
signal (clutch switch-ECOSPLIT,
Wheel-based vehicle speed/CC
active/Brake switch/CC set
speed-without VCM)
Intarder 4103F CAN-message ERC1_ER failure 04 No signal CAN message timeout or faulty Yellow
signal (Engine retarder torque
mode-without VCM)
Intarder 41040 CAN-message ETC1 failure 04 No signal CAN message timeout or faulty Yellow
signal (shift in process, output shaft
speed), only with ET2.
Intarder 41042 CAN-message ETP failure (SAE J1939) 04 No signal CAN message timeout or faulty Yellow
signal engine coolant temperature),
only with EBL
Intarder 41034 CAN-message TSC1_VCMD failure 04 No signal CAN message timeout - detected if Yellow
message after key on was present
or faulty signal
Intarder 41051 CAN-message BC_DR timeout 04 No signal CAN message timeout or faulty Yellow
signal (lever position)
MET 26D01 EEPROM checksum error 0C Yellow
MET 26D02 ECU Overheating The PCB ECU Temperature of the output drivers is greater 0C Yellow
than max. allowed temperature (100°C).
MET 26D03 ECU Secondary Microprocessor Faulty The secondary microprocessor that executes the limp-home 0C Yellow
function is faulty
MET 26D0C Body Control bus CAN No CAN messages on Body Control bus or Bus-Off detection. 02 Red
The error can be read on BCB CAN only if the BCB CAN bus
resets
MET 26D20 Fuel Level sensor Fuel Level interface failure detected. 03 Voltage above normal (s.c. to battery) Yellow
The input voltage is evaluated for Phisically possible range
MET 26D20 Fuel Level sensor 04 Voltage below normal (s.c. to ground). Yellow
Only when the current is sensed on the
Low Side
MET 26D21 Engine Oil Level Sensor Fuel Level interface failure detected. 03 Voltage above normal (s.c. to battery) Yellow
The input voltage is evaluated for Phisically possible range
MET 26D21 Engine Oil Level Sensor 04 Voltage below normal (s.c. to ground). Yellow
Only when the current is sensed on the
Low Side
MET 26D51 Parking Left & Right Front Lights & Analog Diagnostic: short circuit to ground or Overload or 06 short circuit to ground or Overload or Yellow
Parking Rear Left Lights & Overheating protection. Overheating protection
Marker Rear Left & Right Lights & The test is performed only when the driver is On. The error is
Trailer Parking Lights Left/Side Marker detected only when the relative supply voltage is between 18V
Left Lights and 32V.
MET 26D52 Parking Left & Right Analog Diagnostic: The acquired load current is below the 05 I < IS Yellow
Front Lights threshold.
The current follows the I to V linear characteristic of the lamps.
The error is detected only when the relative supply voltage is
between 18V and 32V.
MET 26D53 Parking Rear Left Lights Analog Diagnostic: The acquired load current is below the 05 I < IS Yellow
threshold.
The current follows the I to V linear characteristic of the lamps.
The error is detected only when the relative supply voltage is
between 18V and 32V.
MET 26D54 Parking Rear Right Lights Analog Diagnostic: The acquired load current is below the 05 I < IS Yellow
threshold.
The current follows the I to V linear characteristic of the lamps.
The error is detected only when the relative supply voltage is
between 18V and 32V.
MET 26D55 Parking Rear Right Lights & Analog Diagnostic: short circuit to ground or Overload or 06 short circuit to ground or Overload or Yellow
Plate Left & Right Lights & Overheating protection. Overheating protection
Trailer Parking Lights Left/Side Marker The test is performed only when the driver is On. The error is
Left Lights detected only when the relative supply voltage is between 18V
and 32V.
MET 26D56 Rear Fog Left & Right Lights Analog Diagnostic: The acquired load current is below the 05 I < IS Yellow
threshold.
The current follows the I to V linear characteristic of the lamps.
The error is detected only when the relative supply voltage is
between 18V and 32V.

Bianca Andreana Trakker E4 Errors list Print Date: 21.11.2021

ELTRAC ET-TN-445-87 - Trakker E4 Error Codes Page 23 of 30

ECU SPN F aultCo m p o

nen
t D
es
crip
tio
n F MI FM I C
omm
en
t L
amps
tat
u s M
ILL
amp
N
am e [Hex] [
H e
x] D escript
io n
MET 26D57 Rear Fog Left & Analog Diagnostic: short circuit to ground or Overload or 06 short circuit to ground or Overload or Yellow
Right Lights & Overheating protection. Overheating protection
Trailer Rear Fog Left & The test is performed only when the driver is On. The error is
Right Lights detected only when the relative supply voltage is between 18V
and 32V.
MET 26D58 Stop Light Left Analog Diagnostic: The acquired load current is below the 05 I < IS Yellow
threshold.
The current follows the I to V linear characteristic of the lamps.
The error is detected only when the relative supply voltage is
between 18V and 32V.
MET 26D59 Stop Light Right Analog Diagnostic: The acquired load current is below the 05 I < IS Yellow
threshold.
The current follows the I to V linear characteristic of the lamps.
The error is detected only when the relative supply voltage is
between 18V and 32V.
MET 26D5A Stop Light Left & Analog Diagnostic: short circuit to ground or Overload or 06 short circuit to ground or Overload or Yellow
Stop Light Right & Overheating protection. Overheating protection
Trailer Stop Left & Right Lights The test is performed only when the driver is On. The error is
detected only when the relative supply voltage is between 18V
and 32V.
MET 26D5B Front Fog Left & Right Lights Analog Diagnostic: short circuit to ground or Overload or 06 short circuit to ground or Overload or Yellow
Overheating protection. Overheating protection
The test is performed only when the driver is On. The error is
detected only when the relative supply voltage is between 18V
and 32V.
MET 26D5C Low Beam Light Left On/Off Diagnostic 05 Open load Yellow
MET 26D5C Low Beam Light Left 06 short circuit to ground or Overload or Yellow
Overheating protection
MET 26D5D Low Beam Light Right On/Off Diagnostic 05 Open load Yellow
MET 26D5D Low Beam Light Right 06 short circuit to ground or Overload or Yellow
Overheating protection
MET 26D5E High Beam Light Left On/Off Diagnostic 05 Open load Yellow
MET 26D5E High Beam Light Left 06 short circuit to ground or Overload or Yellow
Overheating protection
MET 26D5F High Beam Light Right On/Off Diagnostic 05 Open load Yellow
MET 26D5F High Beam Light Right 06 short circuit to ground or Overload or Yellow
Overheating protection
MET 26D60 Plate Left & Right Lights Analog Diagnostic: The acquired load current is below the 05 I < IS Yellow
threshold.
The current follows the I to V linear characteristic of the lamps.
The error is detected only when the relative supply voltage is
between 18V and 32V.
MET 26D62 Marker Rear Left & Right Lights Analog Diagnostic: The acquired load current is below the 05 I < IS Yellow
threshold.
The current follows the I to V linear characteristic of the lamps.
The error is detected only when the relative supply voltage is
between 18V and 32V.
MET 26D67 Reverse Gear Lights On/Off Diagnostic 05 Open load Yellow
MET 26D67 Reverse Gear Lights 06 short circuit to ground or Overload or Yellow
Overheating protection
MET 26D68 Turn Right Lights Analog Diagnostic: The acquired load current is below the 05 I < IS Yellow
threshold.
The current follows the I to V linear characteristic of the lamps.
The error is detected only when the relative supply voltage is
between 18V and 32V.
MET 26D69 Trailer Turn Lights Right Analog Diagnostic: The acquired load current is below the 05 I < IS Yellow
threshold.
The current follows the I to V linear characteristic of the lamps.
The error is detected only when the relative supply voltage is
between 18V and 32V.
MET 26D6A Turn & Trailer Turn Right Lights Analog Diagnostic: short circuit to ground or Overload or 06 short circuit to ground or Overload or Yellow
Overheating protection. Overheating protection
The test is performed only when the driver is On. The error is
detected only when the relative supply voltage is between 18V
and 32V.
MET 26D6B Turn Left Lights Analog Diagnostic: The acquired load current is below the 05 I < IS Yellow
threshold.
The current follows the I to V linear characteristic of the lamps.
The error is detected only when the relative supply voltage is
between 18V and 32V.
MET 26D6C Trailer Turn Lights Left Analog Diagnostic: The acquired load current is below the 05 I < IS Yellow
threshold. Is=40mA
The threshold is 40mA. The error is detected only when the
relative supply voltage is between 18V and 32V.
MET 26D6D Turn & Trailer Turn Left Lights Analog Diagnostic: short circuit to ground or Overload or 06 short circuit to ground or Overload or Yellow
Overheating protection. Overheating protection
The test is performed only when the driver is On. The error is
detected only when the relative supply voltage is between 18V
and 32V.
MET 26D6E Trailer Stop Left & Right Lights Analog Diagnostic: The acquired load current is below the 05 I < IS Yellow
threshold. Is=40mA
The threshold is 40mA. The error is detected only when the
relative supply voltage is between 18V and 32V.
MET 26DA1 P-C1 output: Ignition Key 15 & Body On/Off Diagnostic 06 short circuit to ground or Overload or Yellow
Builder &Trailer Overheating protection
MET 26DC3 Headbeam Adjustment On/Off Diagnostic 03 Short circuit to battery Yellow
MET 26DC3 Headbeam Adjustment 06 Short circuit to ground (with Yellow
Hheadbeam Adjustment Position > 4%)
MET 26DC5 A-C1 output: Air Conditioning On/Off Diagnostic 05 Open Load (test with driver ON, I<0.5A) Yellow
Compressor
MET 26DC5 A-C1 output: Air Conditioning 06 Short circuit to ground or Overload or Yellow
Compressor Overheating protection
MET 26DC8 C-A1 output: S-APU Valve On/Off Diagnostic 05 Open Load Yellow
S2-Regeneration Transmission High
Range Valve(Astra)
MET 26DC8 C-A1 output: S-APU Valve 06 short circuit to ground or Overload or Yellow
S2-Regeneration Transmission High Overheating protection
Range Valve(Astra)
MET 26DC8 C-A1 output: S-APU Valve 03 Short circuit to battery Yellow
S2-Regeneration Transmission High
Range Valve(Astra)
MET 26DC9 C-A2 output: S-APU Valve S1-Unloader On/Off Diagnostic 05 Open Load Yellow
Transmission Low Range Valve(Astra)
MET 26DC9 C-A2 output: S-APU Valve S1-Unloader 06 short circuit to ground or Overload or Yellow
Transmission Low Range Valve(Astra) Overheating protection
MET 26DC9 C-A2 output: S-APU Valve S1-Unloader 03 Short circuit to battery Yellow
Transmission Low Range Valve(Astra)
MET 26DCA C-A3 output: Differential Lock – Rear On/Off Diagnostic 05 Open Load Yellow
Axle 1
MET 26DCA C-A3 output: Differential Lock – Rear 06 short circuit to ground or Overload or Yellow
Axle 1 Overheating protection
MET 26DCA C-A3 output: Differential Lock – Rear 03 Short circuit to battery Yellow
Axle 1
MET 26DCD C-A4 output: Differential Lock – Central On/Off Diagnostic 05 Open Load Yellow
MET 26DCD C-A4 output: Differential Lock – Central 06 short circuit to ground or Overload or Yellow
Overheating protection
MET 26DCD C-A4 output: Differential Lock – Central 03 Short circuit to battery Yellow
MET 26DCE C-A5 output: Differential Lock – Front On/Off Diagnostic 05 Open Load Yellow
Axle 1 & Servoshift Valve
MET 26DCE C-A5 output: Differential Lock – Front 06 short circuit to ground or Overload or Yellow
Axle 1 Servoshift Valve Overheating protection
MET 26DCE C-A5 output: Differential Lock – Front 03 Short circuit to battery Yellow
Axle 1 Servoshift Valve
MTCO 900A System performance Other errors, messages by the CANcontroller: SPN
e.g. no station, no acknowledgment, etc. (This error will be visualized on
suppressed approx. 10 seconds after ignition "on".) MTCO, on IC
only specific
Tell Tale or
Icon
MTCO 900B System performance CAN controller signals Status Bus Off
Significant errors on the CAN bus, possiblecauses:
Errors at the bus medium
Errors in the physical layer
Log error.
MTCO 900F System performance Keypad error:
Key pressed too long
Key(s) blocked.
MTCO 9010 System performance LCD error:
LCD or actuation defective and / orincorrect.
MTCO 9051 Handling information User information:
Chart for driver 1 is missing.
In case the chart is missing (driver 1) the working time group
for driver 1 has been changed from "" to another working time
group.

Bianca Andreana Trakker E4 Errors list Print Date: 21.11.2021

ELTRAC ET-TN-445-87 - Trakker E4 Error Codes Page 24 of 30

ECU S PN F aultCo mp
one
nt D
es
crip
tio
n F MI F
M I C
omm
en
t L
amps
tat
u s M
ILL
amp
Name [
H ex] [
H e
x] D
es
crip
tio
n
MTCO 9052 Handling information User information:
Chart for driver 2 is missing.
In case the chart is missing (driver 2) the working time group
fordriver 2 has been changed from "" to another working time
group.
MTCO 9053 Handling information User information:
Update chart carrier settings
The MTCO 1324 has detected a differenceThe MTCO 1324
has detected a differencebetween the time in the display and
the chart carrier of > 2 min.
MTCO 9060 System performance Error at the drawer:
Drawer does not open, possible causes:
Chart(s) not correctly or inserted whiledamaged.
Incorrect installation of the MTCO 1324,mechanical jamming
of the drawer.
The engine does not start up.
MTCO 9061 System performance Error in the v-system:
Actuation, stepping motor or driver defective.
MTCO 9062 System performance Error in the duplicating recorder system(MFS):
Actuation, stepping motor or driver defective.
MTCO 9063 System performance Error in the recorder lifting system (SAS):
Actuation, stepping motor or driverdefective.
SAS cannot approach the definedpositions.
MTCO 9064 System performance Error when updating the chart carrier settings
or.
Error in the actuation of the chart carrier.
MTCO 9430 System performance Error at "B7" v-pulse output
Possible causes:
Cable between MTCO 1324 andconnected control device
defective.
Connect control device at "B7" defective.
MTCO 1324 at output "B7" defective
MTCO A00C System performance Internal error in the MTCO 1324:Faulty communication with
internalcomponents.
MTCO A050 System Event Trip without chart:
Chart for driver 1 not inserted:
The MTCO has recorded distance pulses for more than 7 sec.
and has detected a trip without chart.
MTCO A400 System Event Power loss at the MTCO 1324orMTCO 1324 has detected an
undervoltage.
MTCO A411 System performance Communication between the MTCO 1324and the E-Tacho
1323 or the combi instrument interrupted
MTCO A423 System Event Error in communication to the KITAS 2170.
Problems within the communication online "B4".
MTCO A822 System Event Error in the communication to theKITAS 2170:
KITAS 2170 not "activated".
KITAS serial number faulty when checkedwithin the MTCO
1324.
Pulse ratio (real time signal) "B3"incorrect.
KITAS 2170 sensor key faulty when checked within the MTCO
1324 or
unexpec
SWI 47110 Steering Wheel & Column fault 16 Red
UDS 43D13 Battery voltage sensing (electrical) ABSI_D_DTC_CUW 03 Signal high On On
UDS 43D13 Battery voltage sensing (electrical) 04 Signal low On On
UDS 43D15 Temperature sensor after catalyst ACTD_D_DTC_CUW 03 Signal high On On
(electrical and plausibility)
UDS 43D15 Temperature sensor after catalyst 04 Signal low On On
(electrical and plausibility)
UDS 43D16 Temperature sensor before catalyst ACTU_D_DTC_CUW 03 Signal high On On
(electricl and plausiblity)
UDS 43D16 Temperature sensor before catalyst 04 Signal low On On
(electricl and plausiblity)
UDS 43D17 Supply Sensor 1 (5V internal; for UREA m: DSS1_D_DTC_CUW 02 Supply voltage too high Failure path disabled Off Off
level sensor) h: ASS1_D_DTC_CUW
UDS 43D17 Supply Sensor 1 (5V internal; for UREA 03 Supply voltage too low Failure path disabled Off Off
level sensor)
UDS 43D18 Sensor supply 2 (5V internal; for UREA m: DSS2_D_DTC_CUW 02 Supply voltage too high Off On
pressure sensors) h: ASS2_D_DTC_CUW
UDS 43D18 Sensor supply 2 (5V internal; for UREA 03 Supply voltage too low Off On
pressure sensors)
UDS 43D19 UREA pressure sensor in box (electrical AUPS_D_DTC_CUW 03 Signal high On On
and plausibility)
UDS 43D19 UREA pressure sensor in box (electrical 04 Signal low On On
and plausibility)
UDS 43D19 UREA pressure sensor in box (electrical 02 Supply voltage error On On
and plausibility)
UDS 43D1A UREA Temperature sensor in box AUTB_D_DTC_CUW 03 Signal high Off Off
(electrical and plausibility)
UDS 43D1A UREA Temperature sensor in box 04 Signal low Off Off
(electrical and plausibility)
UDS 43D21 Voltage supply internal heaters 1 (UB1) ABV1_D_DTC_CUW 05 Open circuit to UB1 On On
electrical
UDS 43D21 Voltage supply internal heaters 1 (UB1) 06 Short to bat at UB1 with Key 15 off On On
electrical
UDS 43D22 Voltage supply 2 - tube heaters (UB2) ABV2_D_DTC_CUW 03 Short to bat at UB2 with Key 15 off Off Off
electrical
UDS 43D22 Voltage supply 2 - tube heaters (UB2) 04 Open circuit to UB2 Off Off
electrical
UDS 43D22 Voltage supply 2 - tube heaters (UB2) 05 Short circuit to Ground UB2 Off Off
electrical
UDS 43D23 Voltage supply 3 - Coolant control valve ABV3_D_DTC_CUW 03 Short to bat at UB3 with Key 15 off Off Off
and reverting valve (UB3) electrical
UDS 43D23 Voltage supply 3 - Coolant control valve 04 Open circuit to UB3 Off Off
and reverting valve (UB3) electrical
UDS 43D23 Voltage supply 3 - Coolant control valve 05 Short circuit to Ground UB3 Off Off
and reverting valve (UB3) electrical
UDS 43D24 Monitoring VDD11 voltage - Dosing AV11_D_DTC_CUW 03 Supply voltage high Off Off
valve
UDS 43D24 Monitoring VDD11 voltage - Dosing 04 Supply voltage low Off Off
valve
UDS 43D31 UREA level sensor (electrical) AULS_D_DTC_CUW 03 Signal high Off On
UDS 43D31 UREA level sensor (electrical) 04 Signal low Off On
UDS 43D31 UREA level sensor (electrical) 02 Supply voltage error Off On
UDS 43D32 UREA Temperature sensor in Tank AUTT_D_DTC_CUW 03 Signal high Off Off
(electrical)
UDS 43D32 UREA Temperature sensor in Tank 04 Signal low Off Off
(electrical)
UDS 43D34 UREA Quality sensor EUQS_D_DTC_CUW 05 open wire Failure path disabled Off Off
UDS 43D34 UREA Quality sensor 06 short circuit Failure path disabled Off Off
UDS 43D34 UREA Quality sensor 07 not plausible Failure path disabled Off Off
UDS 43D34 UREA Quality sensor 02 temperature outside operation range Failure path disabled Off Off
UDS 43D34 UREA Quality sensor 00 Concentration higher than specified Failure path disabled Off Off
value
UDS 43D34 UREA Quality sensor 01 concentration is less than specified Failure path disabled Off Off
value
UDS 43D34 UREA Quality sensor 0C empty or partially filled sensor Failure path disabled Off Off
UDS 43D35 NOx sensor (self monitoring of NOXS_D_DTC_CUW 04 Nox sensor Short circuit Failure path disabled Off Off
sensor/only CAN msg)
UDS 43D35 NOx sensor (self monitoring of 03 NOx Sensor Open circuit Failure path disabled Off Off
sensor/only CAN msg)
UDS 43D35 NOx sensor (self monitoring of 0B Other Nox sensor error Failure path disabled Off Off
sensor/only CAN msg)
UDS 43D41 Diagnostic lamp (electrical) PDIA_D_DTC_CUW 04 short circuit to batt + Failure path disabled Off Off
UDS 43D41 Diagnostic lamp (electrical) 03 open circuit or short to ground Failure path disabled Off Off
UDS 43D41 Diagnostic lamp (electrical) 05 Open load Failure path disabled Off Off
UDS 43D52 Dosing Valve (electrical) PUDV_D_DTC_CUW 04 short circuite to ground Off On
UDS 43D52 Dosing Valve (electrical) 03 short circuit to batt + Off On
UDS 43D52 Dosing Valve (electrical) 05 Open load Off On
UDS 43D53 UREA Pump speed PUMP_D_DTC_CUW 07 pump motor blocked Off On
UDS 43D53 UREA Pump speed 08 pump overspeed Off On
UDS 43D53 UREA Pump speed 02 pump motor unplugged Off On
UDS 43D53 UREA Pump speed 0C Hall sensors defect Off On
UDS 43D55 Cooling control valve short circuit to PCCV_D_DTC_CUW 05 Short circuit to batt+ Off Off
Ubat or open load
UDS 43D55 Cooling control valve short circuit to 0B Open load Off Off
Ubat or open load
UDS 43D56 Cooling control valve short circuit to PCCV_D_2_DTC_CUW 0B Short circuit to ground Off Off
ground
UDS 43D57 Reverting Valve (4-2 way valve?) PRVV_D_DTC_CUW 04 short circuit to ground Off Off
electrically
UDS 43D57 Reverting Valve (4-2 way valve?) 03 short circuit to batt Off Off
electrically
UDS 43D57 Reverting Valve (4-2 way valve?) 05 Open load Off Off
electrically
UDS 43D58 Valve Blocked Closed Test failed SUDV_D_DTC_CUW 0C dosing valve blocked closed On On
UDS 43D59 Urea dosing valve blocked PUDB_D_DTC_CUW 06 UREA Dosing valve blocked open Failure path disabled On On

Bianca Andreana Trakker E4 Errors list Print Date: 21.11.2021

ELTRAC ET-TN-445-87 - Trakker E4 Error Codes Page 25 of 30

ECU SPN F
aultC
omp
one
nt D
es
crip
tio
n F MI F M I C
omm
en
t L
amps
tat
u s M
ILL
amp
Na
m e [Hex] [
H e
x] D esc ript
ion
UDS 43D59 Urea dosing valve blocked 05 UREA Dosing Valve blocked closed Failure path disabled On On
UDS 43D61 Line Heater back Flow tube PBFH_D_DTC_CUW 04 Short circuit to ground Failure path disabled Off Off
UDS 43D61 Line Heater back Flow tube 03 Short circuit to battery Failure path disabled Off Off
UDS 43D61 Line Heater back Flow tube 05 Open load Failure path disabled Off Off
UDS 43D63 Line Heater Inlet tube PILH_D_DTC_CUW 04 Short circuit to ground Failure path disabled Off Off
UDS 43D63 Line Heater Inlet tube 03 Short circuit to battery Failure path disabled Off Off
UDS 43D63 Line Heater Inlet tube 05 Open load Failure path disabled Off Off
UDS 43D64 Filter outlet connector heater POCH_D_DTC_CUW 04 Short circuit to ground Failure path disabled Off Off
UDS 43D64 Filter outlet connector heater 03 Short circuit to battery Failure path disabled Off Off
UDS 43D64 Filter outlet connector heater 05 Open load Failure path disabled Off Off
UDS 43D65 Line Heater compression tube PPCH_D_DTC_CUW 04 Short circuit to ground Failure path disabled Off Off
UDS 43D65 Line Heater compression tube 03 Short circuit to battery Failure path disabled Off Off
UDS 43D65 Line Heater compression tube 05 Open load Failure path disabled Off Off
UDS 43D66 Heater of UREA Pump PPHT_D_DTC_CUW 04 short circuit to ground (UB5) Failure path disabled Off Off
UDS 43D66 Heater of UREA Pump 03 short circuit to bat (UB5) Failure path disabled Off Off
UDS 43D66 Heater of UREA Pump 07 Open circuit / broken pump module Failure path disabled Off Off
heater PTC
UDS 43D67 Line Heater pressure tube (Box-Dosing PPLH_D_DTC_CUW 04 Short circuit to ground Failure path disabled Off Off
module)
UDS 43D67 Line Heater pressure tube (Box-Dosing 03 Short circuit to battery Failure path disabled Off Off
module)
UDS 43D67 Line Heater pressure tube (Box-Dosing 05 Open load Failure path disabled Off Off
module)
UDS 43D68 Tank heating Valve PUHT_D_DTC_CUW 04 Short circuit to ground Off Off
UDS 43D68 Tank heating Valve 03 Short circuit to battery Off Off
UDS 43D68 Tank heating Valve 05 Open load Off Off
UDS 43D69 Heater of cooling line PCLH_D_DTC_CUW 04 Short circuit to ground Failure path disabled Off Off
UDS 43D69 Heater of cooling line 03 Short circuit to battery Failure path disabled Off Off
UDS 43D69 Heater of cooling line 05 Open load Failure path disabled Off Off
UDS 43D6A Heater of filterbox (UB5) PFHT_D_DTC_CUW 04 Short circuit to ground Failure path disabled Off Off
UDS 43D6A Heater of filterbox (UB5) 03 Short circuit to battery Failure path disabled Off Off
UDS 43D6A Heater of filterbox (UB5) 07 Open load Failure path disabled Off Off
UDS 43D73 Temperature after catalyst too low SCTD_D_DTC_CUW 07 Downstream catalyst temp - physical Off On
(Catalyst heating time failed)
UDS 43D74 UREA pressure too low at system start SMOT_D_DTC_CUW 02 UREA pressure too low at system start On On
UDS 43D75 UREA pressure too high SUPR_D_DTC_CUW 02 UREA pressure not plausible (urea On On
pressure too high)
UDS 43D76 UREA Temperature in Pump Module out SUTB_D_DTC_CUW 07 Urea temperature box - phisical (Urea Off On
of range Box Temp NOT OK: outside range)
UDS 43D77 UREA Temperature in Tank out of range SUTT_D_DTC_CUW 07 Urea temperature box - phisical (Urea Off Off
Box Temp NOT OK: outside range)
UDS 43D78 System frozen and not free in time HHSM_D_DTC_CUW 07 Defreezing Mode and Detection Errors On On
(Inlet line defreezing failed)
UDS 43D78 System frozen and not free in time 08 Defreezing Mode and Detection Errors On On
(pressure line defreezing failed)
UDS 43D78 System frozen and not free in time 09 Defreezing Mode and Detection Errors On On
(pressure build-up in detection mode
failed)
UDS 43D78 System frozen and not free in time 0A Defreezing Mode and Detection Errors On On
(Back-flow line defreezing failed)
UDS 43D7A Coolant control valve mechanically CCVD_D_DTC_CUW 06 mechanical defective blocked closed Off On
UDS 43D7A Coolant control valve mechanically 05 mechanical defective blocked open Off On
UDS 43D7B Reverting Valve (4-2 way valve?) ERVV_D_DTC_CUW 07 valve does not open Off Off
electrically
UDS 43D7E Battery voltage (actual valve) BMON_D_DTC_CUW 04 low battery voltage On On
UDS 43D7E Battery voltage (actual valve) 03 high battery voltage On On
UDS 43D82 UREA pressure too low (in SMOT_D_C_DTC_CUW 02 Pump motor error during commissioning Off Off
"commissioning" status) (pump not delivering)
UDS 43D83 UREA Temperature too low during STMP_D_C_DTC_CUW 02 Temperatures not plausible during Off Off
commissionning commissioning.
UDS 43D85 Coolant control valve mechanically SCCV_D_C_DTC_CUW 02 blocked closed Off Off
(Commissioning)
UDS 43D93 Static leakage test failed SLKS_D_DTC_CUW 07 static leakage detected (during system On On
state 0)
UDS 43D94 Catalyst efficiency too low (with NOx UCAT_D_DTC_CUW 07 Catalyst efficiency too low Failure path disabled Off Off
sensor)
UDS 43D95 Empty UREA Tank ELMT_D_DTC_CUW 01 urea level below limit 1 On On
UDS 43D96 UREA Level Indication not plausible with PULV_D_DTC_CUW 07 Urea Level Plausibility Error Failure path disabled Off On
UREA consumption
UDS 43D9A Dynamic leakage test failed SLKD_D_DTC_CUW 0C dynamic leakage detected (during On On
system state 1)
UDS 43D9C Urea tank heater valve blocked open HUHT_D_DTC_CUW 07 Tank heater valve blocked open Failure path disabled Off Off
UDS 43D9D NOx sensor measures too high NOx UPPM_D_DTC_CUW 0C NOx ppm not plausible Failure path disabled Off Off
UDS 43DBC Detection of blocked filter DBFE_D_DTC_CUW 07 Error detection of blocked filter Failure path disabled Off Off
UDS 43DBD Warning for detection of blocked filter DBFW_D_DTC_CUW 07 Warning for detection of blocked Filter Failure path disabled Off Off
UDS 43DE1 Plausibility of downstream catalyst PCTD_D_DTC_CUW 0C dynamic plausibility test - upper Failure path disabled Off On
temperature sensor (after SCR catalyst) threshold
UDS 43DE1 Plausibility of downstream catalyst 07 static plausibility test Failure path disabled Off On
temperature sensor (after SCR catalyst)
UDS 43DE2 Plausibility of upstream catalyst PCTU_D_DTC_CUW 0C dynamic plausibility test - upper Failure path disabled Off On
temperature sensor (before SCR threshold
catalyst)
UDS 43DE2 Plausibility of upstream catalyst 07 static plausibility test Failure path disabled Off On
temperature sensor (before SCR
catalyst)
UDS 43DE3 Urea pressure sensor plausibility error PUPS_D_DTC_CUW 0C Plausibility Urea pressure sensor Off On
(checked during system startup) (dynamic)
UDS 43DE4 Urea box temperature sensor plausibility PUTB_D_DTC_CUW 0C Plausibility of pump module temp. ? Off Off
error (dynamic / static) sensor (dynamic)
UDS 43DE4 Urea box temperature sensor plausibility PUTB_D_DTC_CUW 07 Plausibility of pump module temp. ? Off Off
error (dynamic / static) sensor (static)
UDS 43DE5 Urea tank temperature sensor PUTT_D_DTC_CUW 0C Plausibility of urea tank temp. sensor Off Off
plausibility error (dynamic / static) (dynamic)
UDS 43DE5 Urea tank temperature sensor 07 Plausibility of urea tank temp. sensor Off Off
plausibility error (dynamic / static) (static)
UDS 43DE6 UREA Tank Temperature not plausible EUTT_D_DTC_CUW 03 Temp over CAN: SAE J1939 Timeout Failure path disabled Off Off
with Pump module temperature Temp sensor connected directly: SRC
high
UDS 43DE6 UREA Tank Temperature not plausible 04 Temp over CAN: SAE J1939 Too many Failure path disabled Off Off
with Pump module temperature messages
Temp sensor connected directly: SRC
low
UDS 43DE6 UREA Tank Temperature not plausible 02 Temp over CAN: SAE J1939 erroneous Failure path disabled Off Off
with Pump module temperature signal
UDS 43DE7 Back flow line clogged SBFL_D_DTC_CUW 07 back flow line blocked Off Off
UDS 43DE8 Coolant control valve mechanically SCCV_D_DTC_CUW 02 blocked closed Off On
UDS 43DEA pressure line blocked SPRL_D_DTC_CUW 07 pressure line blocked On On
UDS 43DEB Low UREA Level 1 - warning EUL1_D_DTC_CUW 01 urea level below limit 2 Failure path disabled Off Off
UDS 43DEC Low UREA Level 2 - Empty UREA Tank EUL2_D_DTC_CUW 07 urea tank empty Failure path disabled Off Off
UDS 43DA1 CAN receive frame E2SCR (Dosing,Exh CE2S_D_DTC_CUW 09 timeout Off On
gas flow,Exh gas temp,Error
Supression, Heater, Long Term failure)
UDS 43DA1 CAN receive frame E2SCR (Dosing,Exh 0A too many CAN messages Off On
gas flow,Exh gas temp,Error
Supression, Heater, Long Term failure)
UDS 43DA1 CAN receive frame E2SCR (Dosing,Exh 02 SAE J1939 Check for CAN receive Off On
gas flow,Exh gas temp,Error signal : (UREA quantity not in range)
Supression, Heater, Long Term failure)
UDS 43DA1 CAN receive frame E2SCR (Dosing,Exh 0C SAE J1939 Check for CAN receive Off On
gas flow,Exh gas temp,Error signal : (Heating status not in range)
Supression, Heater, Long Term failure)
UDS 43DA1 CAN receive frame E2SCR (Dosing,Exh 07 SAE J1939 Check for CAN receive Off On
gas flow,Exh gas temp,Error signal : (Dosing status not in range)
Supression, Heater, Long Term failure)
UDS 43DA1 CAN receive frame E2SCR (Dosing,Exh 0C SAE J1939 Check for CAN receive Off On
gas flow,Exh gas temp,Error signal : (PTO status not in range)
Supression, Heater, Long Term failure)
UDS 43DA1 CAN receive frame E2SCR (Dosing,Exh 0C SAE J1939 Check for CAN receive Off On
gas flow,Exh gas temp,Error signal : (Exhaust gas mass flow not in
Supression, Heater, Long Term failure) range)
UDS 43DA1 CAN receive frame E2SCR (Dosing,Exh 0C SAE J1939 Check for CAN receive Off On
gas flow,Exh gas temp,Error signal : (Exhaust gas temperature not in
Supression, Heater, Long Term failure) range)
UDS 43DA2 CAN receive frame E2SCR extended CE2S_D_2_DTC_CUW 02 SAE J1939 Check for CAN receive Failure path disabled On Off
(Dosing,Exh gas flow,Exh gas signal : (Long term error active signal in
temp,Error Supression, Heater, Long range)
Term failure)
UDS 43DA2 CAN receive frame E2SCR extended 0C SAE J1939 Check for CAN receive Failure path disabled On Off
(Dosing,Exh gas flow,Exh gas signal : (Error suppression signal not in
temp,Error Supression, Heater, Long range)
Term failure)
UDS 43DA3 CAN receive frame EEC1 (Driver CEEC_D_DTC_CUW 09 timeout Off Off
demand, eng speed, eng torque)
UDS 43DA3 CAN receive frame EEC1 (Driver 0A too many CAN messages Off Off
demand, eng speed, eng torque)

Bianca Andreana Trakker E4 Errors list Print Date: 21.11.2021

ELTRAC ET-TN-445-87 - Trakker E4 Error Codes Page 26 of 30

ECU S P
N Fa ultCom pon en t D
es
crip
tio
n F MI F MI C
omm
en
t L
amps
tat
u s M
ILL
amp
Na
m e [
H e
x] [
H e
x] De scription
UDS 43DA3 CAN receive frame EEC1 (Driver 0C SAE J1939 Check for CAN receive Off Off
demand, eng speed, eng torque) signal : (Torque driver demand not in
range)
UDS 43DA3 CAN receive frame EEC1 (Driver 02 SAE J1939 Check for CAN receive Off Off
demand, eng speed, eng torque) signal : (Engine torque not in range)
UDS 43DA3 CAN receive frame EEC1 (Driver 07 SAE J1939 Check for CAN receive Off Off
demand, eng speed, eng torque) signal : (Engine speed not in range)
UDS 43DA4 CAN receive frame ET1 (Oil and Water CET1_D_DTC_CUW 09 timeout Off Off
temp engine)
UDS 43DA4 CAN receive frame ET1 (Oil and Water 0A too many CAN messages Off Off
temp engine)
UDS 43DA4 CAN receive frame ET1 (Oil and Water 0C SAE J1939 Check for CAN receive Off Off
temp engine) signal : (Water temperature not in
range)
UDS 43DA4 CAN receive frame ET1 (Oil and Water 02 SAE J1939 Check for CAN receive Off Off
temp engine) signal : (Oil temperature not in range)
UDS 43DA6 CAN receive frame IC1 (Boost press, CIC1_D_DTC_CUW 09 timeout Failure path disabled Off Off
Manifold Temp)
UDS 43DA6 CAN receive frame IC1 (Boost press, 0A too many CAN messages Failure path disabled Off Off
Manifold Temp)
UDS 43DA6 CAN receive frame IC1 (Boost press, 0C SAE J1939 Check for CAN receive Failure path disabled Off Off
Manifold Temp) signal : (Boost Pressure not in range)
UDS 43DA6 CAN receive frame IC1 (Boost press, 02 SAE J1939 Check for CAN receive Failure path disabled Off Off
Manifold Temp) signal : (Intake manifold 1 temperature
not in range)
UDS 43DA7 CAN receive frame LFE (Fuel Rate) CLFE_D_DTC_CUW 09 timeout Failure path disabled Off Off
UDS 43DA7 CAN receive frame LFE (Fuel Rate) 0A too many CAN messages Failure path disabled Off Off
UDS 43DA7 CAN receive frame LFE (Fuel Rate) 0C SAE J1939 Check for CAN receive Failure path disabled Off Off
signal : (Fuel rate not in range)
UDS 43DA8 CAN receive frame NO1 (NOx CNO1_D_DTC_CUW 09 timeout Failure path disabled Off Off
concentration, NOx Sensor state)
UDS 43DA8 CAN receive frame NO1 (NOx 0A too many CAN messages Failure path disabled Off Off
concentration, NOx Sensor state)
UDS 43DA8 CAN receive frame NO1 (NOx 0C SAE J1939 Check for CAN receive Failure path disabled Off Off
concentration, NOx Sensor state) signal : (Nox concentration not in range)
UDS 43DA8 CAN receive frame NO1 (NOx 02 SAE J1939 Check for CAN receive Failure path disabled Off Off
concentration, NOx Sensor state) signal : (Nox status not in range)
UDS 43DA9 DCU or Heater switched "off" too long CTIM_D_DTC_CUW 09 Heater disabled by CAN request for a Failure path disabled Off Off
time via CAN too long time
UDS 43DA9 DCU or Heater switched "off" too long 0A Dosing disabled by CAN request for a Failure path disabled Off Off
time via CAN too long time
UDS 43DAA UREA Tank level error (CAN message EULS_D_DTC_CUW 03 Level over CAN: SAE J1939 Signal Not Off On
or electrical with real sensor) in Range
Level sensor connected directly: SRC
high
UDS 43DAA UREA Tank level error (CAN message 04 Level over CAN: SAE J1939 Erraneous Off On
or electrical with real sensor) Signal
Level sensor connected directly: SRC
low
UDS 43DAA UREA Tank level error (CAN message 02 Level over CAN: SAE J1939 no Signal Off On
or electrical with real sensor) available
Level sensor connected directly: Sensor
Supply error
UDS 43DAC UREA quality sensor re lated errors CUQS_D_DTC_CUW 09 timeout Failure path disabled Off Off
CAN
UDS 43DAC UREA quality sensor re lated errors 0A too many CAN messages Failure path disabled Off Off
CAN
UDS 43DAC UREA quality sensor re lated errors 0C SAE J1939 Check for CAN receive Failure path disabled Off Off
CAN signal : (Urea quantity signal not in
range)
UDS 43DAD Can receive Time/Date CTDA_D_DTC_CUW 09 timeout Failure path disabled Off Off
UDS 43DAD Can receive Time/Date 0A too many CAN messages Failure path disabled Off Off
UDS 43DAD Can receive Time/Date 0C SAE J1939 range check error of Failure path disabled Off Off
seconds
UDS 43DAD Can receive Time/Date 0C SAE J1939 range check error of Failure path disabled Off Off
minutes
UDS 43DAD Can receive Time/Date 0C SAE J1939 range check error of hours Failure path disabled Off Off
UDS 43DAD Can receive Time/Date 0C SAE J1939 range check error of months Failure path disabled Off Off
UDS 43DAD Can receive Time/Date 07 SAE J1939 range check error of days Failure path disabled Off Off
UDS 43DAD Can receive Time/Date 07 SAE J1939 range check error of years Failure path disabled Off Off
UDS 43DB1 Ambient Temperature: SAE J1939 CAMB_D_DTC_CUW 09 timeout Off Off
Check for CAN receive signal : (Signal
Range Check: Signal not in range /
Erroreous Signal / Signal not available)
UDS 43DB1 Ambient Temperature: SAE J1939 0A too many CAN messages Off Off
Check for CAN receive signal : (Signal
Range Check: Signal not in range /
Erroreous Signal / Signal not available)
UDS 43DB1 Ambient Temperature: SAE J1939 0C SAE J1939 Check for CAN receive Off Off
Check for CAN receive signal : (Signal signal : (Barometric pressure not in
Range Check: Signal not in range / range)
Erroreous Signal / Signal not available)
UDS 43DB1 Ambient Temperature: SAE J1939 02 SAE J1939 Check for CAN receive Off Off
Check for CAN receive signal : (Signal signal : (Ambient air temperature not in
Range Check: Signal not in range / range)
Erroreous Signal / Signal not available)
UDS 43DB8 CAN receive frame PROA (Fuel CPRO_D_DTC_CUW 09 timeout Failure path disabled Off Off
quantity)
UDS 43DB8 CAN receive frame PROA (Fuel 0A too many CAN messages Failure path disabled Off Off
quantity)
UDS 43DB8 CAN receive frame PROA (Fuel 0C SAE J1939 Check for CAN receive Failure path disabled Off Off
quantity) signal : (UREA tank level not in range)
UDS 43DB8 CAN receive frame PROA (Fuel 02 SAE J1939 Check for CAN receive Failure path disabled Off Off
quantity) signal : (UREA tank temperature not in
range)
UDS 43DB8 CAN receive frame PROA (Fuel 07 SAE J1939 Check for CAN receive Failure path disabled Off Off
quantity) signal : (Fuel injection quantity not in
range)
UDS 43DBE Can receive frame TC1 CTC1_D_DTC_CUW 09 timeout Failure path disabled Off Off
UDS 43DBE Can receive frame TC1 0A too many CAN messages Failure path disabled Off Off
UDS 43DBE Can receive frame TC1 0C SAE J1939 Check for CAN receive Failure path disabled Off Off
signal : (Vehicle speed not in range)
UDS 43DC1 Too many Frozen Cycles of dosing EFCC_D_DTC_CUW 09 additional frozen cycle counter Failure path disabled Off Off
module (eepm_ct_frz2_uc) exceeded maximum
UDS 43DC1 Too many Frozen Cycles of dosing 0A frozen cycle counter (eepm_ct_frz_uc) Failure path disabled Off Off
module exceeded maximum
UDS 43DC2 Application error in MAP selection for UDVC_D_DTC_CUW 0D map selection error (11 map Failure path disabled Off On
UREA quantity calculation calculation)
UDS 43DD1 EEPROM / Checksum failures EEPM_D_DTC_CUW 0C EEPROM Detection error On On
UDS 43DD1 EEPROM / Checksum failures 0D Wrong EEPROM size On On
UDS 43DD1 bc 08 EEPROM communication error On On
UDS 43DD1 EEPROM / Checksum failures 02 EEPROM write error On On
UDS 43DD1 EEPROM / Checksum failures 07 No corresponding variant number error On On
UDS 43DD1 EEPROM / Checksum failures 0C Codierwort error On On
UDS 43DD2 Ingition "on" signal K15 EK15_D_DTC_CUW 02 digital input ignition ON not sensed Off Off
during initialisation
UDS 43DD3 Main Relay opens too early / too late EMRL_D_DTC_CUW 06 main relay shut off too early (before Off On
EEPROM update)
UDS 43DD3 Main Relay opens too early / too late 03 main relay shut off too late Off On
UDS 43DD3 Main Relay opens too early / too late 05 main relay open circuit Off On
UDS 43DD3 Main Relay opens too early / too late 04 main relay short circuit Off On
UDS 43DD4 Too high UREA Temperature in Pump EMRS_D_DTC_CUW 07 On On
over temperature detection (urea temp.
module or Leakage test failed
in pump module)
(Emergency shut off)
UDS 43DD4 Too high UREA Temperature in Pump 0C On On
urea leakage detection (static or
module or Leakage test failed
dynamic)
(Emergency shut off)
UDS 43DF0 Group error path UREA injection control LCNP_D_DTC_CUW 0C Error belonging to group UREA Injection Off On
control
UDS 43DF1 Group error path Air control LDIN_D_DTC_CUW 0C Error belonging to group air control Off On
UDS 43DF2 Group error path catalyst temperature LIUQ_D_DTC_CUW 0C Error belonging to group catalyst Off On
temperature out of range
UDS 43DF3 Group error path NOx exceeded LNTE_D_DTC_CUW 0C Error belonging to group NOx exceeded Off On
active
UDS 43DF4 Group error path UREA Tank empty LTEM_D_DTC_CUW 0C Error belonging to group UREA tank Off On
empty active
VCM 42714 primary brake (Digital Input 1) 02 Data erratic, intermittent or incorrect not plausible Yellow
(application Eltrac)
VCM 42714 primary brake (Digital Input 1) 04 Voltage below normal or shorted low short low Yellow
(device driver)
VCM 42715 secondary brake (Digital Input 2) 02 Data erratic, intermittent or incorrect not plausible Yellow
(application Eltrac)
VCM 42715 secondary brake (Digital Input 2) 04 Voltage below normal or shorted low short low Yellow
(device driver)
VCM 4270B secondary speed limiter (Digital Input 3) 02 Data erratic, intermittent or incorrect not plausible Yellow
(application Eltrac)

Bianca Andreana Trakker E4 Errors list Print Date: 21.11.2021

ELTRAC ET-TN-445-87 - Trakker E4 Error Codes Page 27 of 30

ECU SPN FaultC om p onen t D

es
crip
tio
n F MI F M I C
omm
en
t L
amps
tat
u s M
ILL
amp
Na
m e [Hex] [
H e
x] D esc ription
VCM 4270B secondary speed limiter (Digital Input 3) 04 Voltage below normal or shorted low short low Yellow
(device driver)
VCM 42749 crank request (Digital Input 4) 02 Data erratic, intermittent or incorrect not plausible Yellow
(application Eltrac)
VCM 42749 crank request (Digital Input 4) 04 Voltage below normal or shorted low short low Yellow
(device driver)
VCM 42701 CC set plus (Digital Input 5) 02 Data erratic, intermittent or incorrect not plausible Yellow
(application Eltrac)
VCM 42701 CC set plus (Digital Input 5) 03 Voltage above normal or shorted high short high Yellow
VCM 42702 CC set minus (Digital Input 6) 02 Data erratic, intermittent or incorrect not plausible Yellow
(application Eltrac)
VCM 42702 CC set minus (Digital Input 6) 03 Voltage above normal or shorted high short high Yellow
VCM 42703 CC resume (Digital Input 7) 02 Data erratic, intermittent or incorrect not plausible Yellow
(application Eltrac)
VCM 42703 CC resume (Digital Input 7) 03 Voltage above normal or shorted high short high Yellow
VCM 42704 CC off (Digital Input 8) 02 Data erratic, intermittent or incorrect not plausible Yellow
(application Eltrac)
VCM 42704 CC off (Digital Input 8) 03 Voltage above normal or shorted high short high Yellow
VCM 42732 clutch switch (Digital Input 9) 02 Data erratic, intermittent or incorrect not plausible Yellow
(application Eltrac)
VCM 42732 clutch switch (Digital Input 9) 03 Voltage above normal or shorted high short high Yellow
VCM 4270A adjustable speed limiter (Digital Input 03 Voltage above normal or shorted high short high Yellow
10)
VCM 42705 CC internal / external (Digital Input 11) 03 Voltage above normal or shorted high short high Yellow
VCM 42731 Gear high / low request (Digital Input 12) 02 Data erratic, intermittent or incorrect not plausible Yellow
(application Eltrac)
VCM 42731 Gear high / low request (Digital Input 12) 03 Voltage above normal or shorted high short high Yellow
VCM 42707 economy mode (Digital Input 13) heavy 03 Voltage above normal or shorted high short high Off
VCM 42716 engine brake request (Digital Input 13) medium 03 Voltage above normal or shorted high short high Yellow
VCM 4271A engine brake mode (Digital Input 14) heavy 03 Voltage above normal or shorted high short high Yellow
VCM 42717 engine brake mode 1 (Digital Input 14) medium 03 Voltage above normal or shorted high short high Yellow
VCM 42718 engine brake mode 2 (Digital Input 15) 03 Voltage above normal or shorted high short high Yellow
VCM 42733 neutral switch (Digital Input 16) 03 Voltage above normal or shorted high short high Yellow
VCM 42746 cabin tilted (Digital Input 17) 03 Voltage above normal or shorted high short high Yellow
VCM 42719 parking brake (Digital Input 18) 02 Data erratic, intermittent or incorrect not plausible Yellow
(application Eltrac)
VCM 42719 parking brake (Digital Input 18) 03 Voltage above normal or shorted high short high Yellow
VCM 42747 engine remote start (Digital Input 19) 02 Data erratic, intermittent or incorrect not plausible Yellow
(application Eltrac)
VCM 42747 engine remote start (Digital Input 19) 03 Voltage above normal or shorted high short high Yellow
VCM 42748 engine remote stop (Digital Input 20) 02 Data erratic, intermittent or incorrect not plausible Yellow
(application Eltrac)
VCM 42748 engine remote stop (Digital Input 20) 03 Voltage above normal or shorted high short high Yellow
VCM 4270F PTO1 (Digital Input 21) 03 Voltage above normal or shorted high short high Off
VCM 42710 PTO2 (Digital Input 22) 03 Voltage above normal or shorted high short high Off
VCM 42711 PTO3 (Digital Input 23) 03 voltage above normal or shorted high short high Off
VCM 4273C Low Idle (Digital Input 24) 02 Data erratic, intermittent or incorrect short 5 V Yellow
(application Eltrac)
VCM 4273C Low Idle (Digital Input 24) 03 Voltage above normal or shorted high short 24 V Yellow
VCM 4273C Low Idle (Digital Input 24) 04 Voltage below normal or shorted low short low Yellow
VCM 4273C Low Idle (Digital Input 24) 05 current below normal or open circuit switch does not switches Yellow
VCM 4273C Low Idle (Digital Input 24) 08 abnormal frequency, pulse width or switching point outside specification Yellow
period
VCM 4273C Low Idle (Digital Input 24) 0D out of calibration switching point valid but slight Off
outside specification
VCM 42706 ACC enable (Digital Input 25) 03 Voltage above normal or shorted high short high Off
VCM 42706 ACC enable (Digital Input 25) 04 Voltage below normal or shorted low short low Yellow
VCM 4273B Clutch switch 2 (Digital Input 26) 02 Data erratic, intermittent or incorrect not plausible Yellow
(application Eltrac)
VCM 4273B Clutch switch 2 (Digital Input 26) 03 Voltage above normal or shorted high short high Yellow
VCM 4273B Clutch switch 2 (Digital Input 26) 04 Voltage below normal or shorted low short low Yellow
VCM 42720 Fan control pressure switch 18 bar 03 Voltage above normal or shorted high short high Yellow
(Digital Input 27)
VCM 42720 Fan control pressure switch 18 bar 04 Voltage below normal or shorted low short low Yellow
(Digital Input 27)
VCM 42721 Fan control pressure switch 22 bar 03 Voltage above normal or shorted high short high Yellow
(Digital Input 28)
VCM 42721 Fan control pressure switch 22 bar 04 Voltage below normal or shorted low short low Yellow
(Digital Input 28)
VCM 42734 D - automatic / manual (Digital Input 29) 02 Data erratic, intermittent or incorrect not plausible Yellow
(application Eltrac)
VCM 42734 D - automatic / manual (Digital Input 29) 03 Voltage above normal or shorted high short high Yellow
VCM 42735 R - reverse (Digital Input 30) 02 Data erratic, intermittent or incorrect not plausible Yellow
(application Eltrac)
VCM 42735 R - reverse (Digital Input 30) 03 Voltage above normal or shorted high short high Yellow
VCM 42736 N - neutral shifting (Digital Input 31) 02 Data erratic, intermittent or incorrect not plausible Yellow
(application Eltrac)
VCM 42736 N - neutral shifting (Digital Input 31) 03 Voltage above normal or shorted high short high Yellow
VCM 42737 gear up shift request (Digital Input 32) 02 Data erratic, intermittent or incorrect not plausible Yellow
(application Eltrac)
VCM 42737 gear up shift request (Digital Input 32) 03 Voltage above normal or shorted high short high Yellow
VCM 42738 gear down shift request (Digital Input 33) 02 Data erratic, intermittent or incorrect not plausible Yellow
(application Eltrac)
VCM 42738 gear down shift request (Digital Input 33) 03 Voltage above normal or shorted high short high Yellow
VCM 42739 Dm special manoeuvring (Digital Input 02 Data erratic, intermittent or incorrect not plausible Yellow
34) (application Eltrac)
VCM 42739 Dm special manoeuvring (Digital Input 03 Voltage above normal or shorted high short high Yellow
34)
VCM 4273A Rm special manoeuvring (Digital Input 02 Data erratic, intermittent or incorrect not plausible Yellow
35) (application Eltrac)
VCM 4273A Rm special manoeuvring (Digital Input 03 Voltage above normal or shorted high short high Yellow
35)
VCM 4273D accelerator pedal (Analog Input 1) 00 Data valid but above normal operation Analog value valid but slight too Off
range high
VCM 4273D accelerator pedal (Analog Input 1) 01 Data valid but below normal operation Analog value valid but slight too low Off
range
VCM 4273D accelerator pedal (Analog Input 1) 02 Data erratic, intermittent or incorrect Analog value too high Yellow
(application Eltrac)
VCM 4273D accelerator pedal (Analog Input 1) 03 Voltage above normal or shorted high Short 24V Yellow
VCM 4273D accelerator pedal (Analog Input 1) 04 Voltage below normal or shorted low Short low Yellow
VCM 4273D accelerator pedal (Analog Input 1) 0D out of calibration Analog value too low Yellow
VCM 4273D accelerator pedal (Analog Input 1) 0E special instructions Short 5V Yellow
VCM 4275B ACC distance selector input (Analog 03 Voltage above normal or shorted high not supported: short high Yellow
Input 2)
VCM 4275B ACC distance selector input (Analog 04 Voltage below normal or shorted low short low Yellow
Input 2)
VCM 4275F Accelerator pedal sensor 2 (Analog 00 Data valid but above normal operation analog value valid but slight too Off
Input 3) range high
VCM 4275F Accelerator pedal sensor 2 (Analog 01 Data valid but below normal operation analog value valid but slight too low Off
Input 3) range
VCM 4275F Accelerator pedal sensor 2 (Analog 02 Data erratic, intermittent or incorrect analog value too high Yellow
Input 3)
VCM 4275F Accelerator pedal sensor 2 (Analog 03 Voltage above normal or shorted high short 24 V Yellow
Input 3)
VCM 4275F Accelerator pedal sensor 2 (Analog 04 Voltage below normal or shorted low short low Yellow
Input 3)
VCM 4275F Accelerator pedal sensor 2 (Analog 0D out of calibration Yellow
Input 3)
VCM 4275F Accelerator pedal sensor 2 (Analog 0E special instructions Yellow
Input 3)
VCM 42760 Accelerator pedal correlation 0D out of calibration Pedal correlation first threshold Yellow
VCM 42760 Accelerator pedal correlation 0E special instructions Pedal correlation second threshold Yellow
VCM 42722 BB Neutral (High Side Output 1) 03 Voltage above normal or shorted high short high Yellow
VCM 42722 BB Neutral (High Side Output 1) 04 Voltage below normal or shorted low short low Yellow
VCM 42722 BB Neutral (High Side Output 1) 05 current below normal or open circuit not supported: open circuit Yellow
VCM 42723 Output Single H Gear 1 / ACC Lamp 03 Voltage above normal or shorted high short high Yellow
(High Side Output 2)
VCM 42723 Output Single H Gear 1 / ACC Lamp 04 Voltage below normal or shorted low short low Yellow
(High Side Output 2)
VCM 42723 Output Single H Gear 1 / ACC Lamp 05 current below normal or open circuit open circuit Yellow
(High Side Output 2)
VCM 42726 BB Parking Brake (High Side Output 3) 03 Voltage above normal or shorted high short high Yellow
VCM 42726 BB Parking Brake (High Side Output 3) 04 Voltage below normal or shorted low short low Yellow
VCM 42726 BB Parking Brake (High Side Output 3) 05 current below normal or open circuit not supported: open circuit Yellow
VCM 42727 Output Single H Gear 2 / ACC Buzzer 03 Voltage above normal or shorted high short high Yellow
(High Side Output 4)
VCM 42727 Output Single H Gear 2 / ACC Buzzer 04 Voltage below normal or shorted low short low Yellow
(High Side Output 4)
VCM 42727 Output Single H Gear 2 / ACC Buzzer 05 current below normal or open circuit open circuit Yellow
(High Side Output 4)
VCM 42728 BB Service Brake (High Side Output 5) 03 Voltage above normal or shorted high short high Yellow
VCM 42728 BB Service Brake (High Side Output 5) 04 Voltage below normal or shorted low short low Yellow
VCM 42728 BB Service Brake (High Side Output 5) 05 current below normal or open circuit not supported: open circuit Yellow
VCM 42729 BB Programmable Threshold Speed 03 Voltage above normal or shorted high short high Yellow
(High Side Output 6)
VCM 42729 BB Programmable Threshold Speed 04 Voltage below normal or shorted low short low Yellow
(High Side Output 6)

Bianca Andreana Trakker E4 Errors list Print Date: 21.11.2021

ELTRAC ET-TN-445-87 - Trakker E4 Error Codes Page 28 of 30

ECU SPN F aultC om pon ent D

es
crip
tio
n F MI FM I C
omm
en
t L
amps
tat
u s M
ILL
amp
Na
m e [Hex] [
H e
x] D escriptio n
VCM 42729 BB Programmable Threshold Speed 05 current below normal or open circuit not supported: open circuit Yellow
(High Side Output 6)
VCM 4274A crank relay (High Side Output 7) 03 Voltage above normal or shorted high short high Yellow
VCM 4274A crank relay (High Side Output 7) 04 Voltage below normal or shorted low short low Yellow
VCM 4274A crank relay (High Side Output 7) 05 current below normal or open circuit not supported: open circuit Yellow
VCM 4274B crank relay (Low Side Output 1) 03 Voltage above normal or shorted high short high Yellow
VCM 4274B crank relay (Low Side Output 1) 04 Voltage below normal or shorted low short low Yellow
VCM 4274B crank relay (Low Side Output 1) 05 current below normal or open circuit open circuit Yellow
VCM 4274B crank relay (Low Side Output 1) 06 Current above normal or grounded external crank relay activation Red
circuit
VCM 4272A BB Clutch Pedal (Low Side Output 2) 03 Voltage above normal or shorted high short high Yellow
VCM 4272A BB Clutch Pedal (Low Side Output 2) 04 Voltage below normal or shorted low short low Yellow
VCM 4272A BB Clutch Pedal (Low Side Output 2) 05 current below normal or open circuit not supported: open circuit Yellow
VCM 42750 Immobilizer LED (Low Side Output 3) 03 Voltage above normal or shorted high short high Yellow
VCM 42750 Immobilizer LED (Low Side Output 3) 04 Voltage below normal or shorted low short low Yellow
VCM 42750 Immobilizer LED (Low Side Output 3) 05 current below normal or open circuit open circuit Yellow
VCM 427F0 Power Supply Key 15 02 Data erratic, intermittent or incorrect Key 15 transition resistence Yellow
(application Eltrac)
VCM 427F0 Power Supply Key 15 03 Voltage above normal or shorted high Key 15 active and CAN status Yellow
inactive
VCM 427F0 Power Supply Key 15 04 Voltage below normal or shorted low Key 15 inactive and CAN status Yellow
active
VCM 427F1 Power Supply Key 30 00 Analog value valid but slight too high over voltage Off
VCM 427F1 Power Supply Key 30 01 analog value valid but slight too low under voltage Off
VCM 4273E Acc. Pedal Power Supply (5 V supply) 02 Data erratic, intermittent or incorrect Supply out of range Yellow
(application Eltrac)
VCM 4273E Acc. Pedal Power Supply (5 V supply) 04 Voltage below normal or shorted low Supply short low Yellow
VCM 4275C ACC dist. Sel. / Pedal sensor 2 supply (5 02 Data erratic, intermittent or incorrect Supply out of range Yellow
V supply) (application Eltrac)
VCM 4275C ACC dist. Sel. / Pedal sensor 2 supply (5 03 Voltage above normal or shorted high Supply short high Yellow
V supply)
VCM 4275C ACC dist. Sel. / Pedal sensor 2 supply (5 04 Voltage below normal or shorted low Supply short low Yellow
V supply)
VCM 4275A ACC Sensor 1 0B Failure mode not identificable Sensor comunication error Off
VCM 4275A ACC Sensor 1 0C bad intelligent device or component Sensor continuosly not available Off
VCM 4275A ACC Sensor 1 0D out of calibration Sensor temperature not available Off
VCM 4275E ACC Sensor 2 0E special instructions sensor dirty Yellow
VCM 42741 Frequency Input (only B7 signal) 03 Voltage above normal or shorted high short high Yellow
VCM 42741 Frequency Input (only B7 signal) 04 Voltage below normal or shorted low (not supported) short low Yellow
VCM 42741 Frequency Input (only B7 signal) 0A abnormal rate of change signal high duration out of Yellow
specification
VCM 4275D ACC Parameter 0D out of calibration Flash parameter not correct Yellow
VCM 427F2 Internal Failure 1 (Runcontrol) 0C bad intelligent device or component External rucontrol Red
VCM 427F2 Internal Failure 1 (Runcontrol) 0D out of calibration Internal rucontrol Red
VCM 427F2 Internal Failure 1 (Runcontrol) 0E special instructions Watchdog timeout Red
VCM 427FD Internal Failure 2 (EEPROM) 02 Data erratic, intermittent or incorrect Checksum parameter range Off
(application Eltrac)
VCM 427FD Internal Failure 2 (EEPROM) 0B Failure mode not identificable Checksum environment data Off
VCM 427FD Internal Failure 2 (EEPROM) 0C bad intelligent device or component Checksum engine values Off
VCM 427FD Internal Failure 2 (EEPROM) 0D out of calibration Checksum immobilizer range Yellow
VCM 427FD Internal Failure 2 (EEPROM) 0E special instructions Checksum production data Yellow
VCM 427FD Internal Failure 2 (EEPROM) 1F not available or condition exists not supported: Checksum runtime Yellow
counter
VCM 427FB Internal Failure 3 (RAM / ROM) 02 Data erratic, intermittent or incorrect RAM failuire Red
(application Eltrac)
VCM 427FB Internal Failure 3 (RAM / ROM) 0D out of calibration ROM failure Red
VCM 427FE Internal Failure 4 (Controller) 0B Failure mode not identificable Parameter version wrong Red
VCM 427FE Internal Failure 4 (Controller) 0C bad intelligent device or component Operating system failure Red
VCM 427FE Internal Failure 4 (Controller) 0D out of calibration Software trap Red
VCM 427FE Internal Failure 4 (Controller) 0E special instructions Controller failure Red
VCM 427FA Internal Failure 5 (Bootloader) 0C bad intelligent device or component Flash parameter failure Red
VCM 427FA Internal Failure 5 (Bootloader) 0D out of calibration Flash program failure Red
VCM 427F3 Internal Failure 6 (Rx Lookuptable) 0D out of calibration CAN Lookuptable overflow Red
VCM 427F4 Internal Failure 7 (CPU overlooad) 02 Data erratic, intermittent or incorrect CPU overload Off
(application Eltrac)
VCM 427B4 Immobilizer1 02 Data erratic, intermittent or incorrect Transponder programming not Yellow
(application Eltrac) possible
VCM 427B4 Immobilizer1 0B Failure mode not identificable Transponder programming not Yellow
possible
VCM 427B4 Immobilizer1 0C bad intelligent device or component Different pin source within keyset Yellow
VCM 427B4 Immobilizer1 0D out of calibration IDE has been read twice or is equal Yellow
0
VCM 427B4 Immobilizer1 0E special instructions Max number of keys exceeded Yellow
VCM 427B5 Immobilizer2 02 Data erratic, intermittent or incorrect Ignition not switched off in time Yellow
(application Eltrac)
VCM 427B5 Immobilizer2 0B Failure mode not identificable Unknown IDE Yellow
VCM 427B6 Immobilizer3 0C bad intelligent device or component No communication to ECM Yellow
VCM 427B6 Immobilizer3 0D out of calibration Unknown ECM Yellow
VCM 427B6 Immobilizer3 0E special instructions No immobilizer function in ECM Yellow
VCM 427B7 Immobilizer4 02 Data erratic, intermittent or incorrect VCM in plant mode Yellow
(application Eltrac)
VCM 427B7 Immobilizer4 0B Failure mode not identificable ECM in plant mode and learning Yellow
already completed
VCM 427B8 Immobilizer in plant mode 02 Data erratic, intermittent or incorrect VCM in plant mode and key Yellow
(application Eltrac) learning active
VCM 427B9 Immobilizer5 02 Data erratic, intermittent or incorrect Bit error in transponder response Yellow
(application Eltrac)
VCM 427B9 Immobilizer5 07 mechanicial system not responding Antenna hardware error Yellow
properly
VCM 427B9 Immobilizer5 0B Failure mode not identificable Internal operation error Yellow
VCM 427B9 Immobilizer5 0C bad intelligent device or component No transponder response Yellow
VCM 42764 TSC1 Handling 00 Data valid but above normal operation Most severe level: positive engine Yellow
range brake torque control
VCM 42764 TSC1 Handling 01 Data valid but below normal operation Most severe level: negative torque Yellow
range control detection
VCM 42764 TSC1 Handling 0B Root cause not known Speed request over plausible Yellow
windows
VCM 42764 TSC1 Handling 0C bad intelligent device or component Incoherent requests of fuelling and Yellow
negative torque
VCM 42764 TSC1 Handling 12 Data valid but below normal operational Moderately severe level: negative Yellow
range torque limit request
VCM 42765 Powertrain and Brake request 0B Root cause not known Active at least one error relative to Yellow
Evaluation TSC1_TE (44 ; 50 ; 38 ; 32 ; 20 ; 26
; 14 ; 8 ; 2)
VCM 42766 Powertrain and Brake request 0B Root cause not known Active at least one error relative to Yellow
Evaluation TSC1_AE (43 ; 49 ; 37 ; 31 ; 19 ; 25
; 13 ; 7 ; 1)
VCM 42767 Powertrain and Brake request 0B Root cause not known Active at least one error relative to Yellow
Evaluation TSC1_DE (45 ; 51 ; 39 ; 33 ; 21 ; 27
; 15 ; 9 ; 3)
VCM 42768 Powertrain and Brake request 0B Root cause not known Active at least one error relative to Yellow
Evaluation TSC1_PE (ICB) (47 ; 53 ; 41 ; 35 ;
23 ; 29 ; 17 ; 11 ; 5)
VCM 42769 Powertrain and Brake request 0B Root cause not known Active at least one error relative to Yellow
Evaluation TSC1_PE (VDB) (48 ; 54 ; 42 ; 36 ;
24 ; 30 ; 18 ; 12 ; 6)
VCM 4276A Powertrain and Brake request 0B Root cause not known Active at least one error relative to Yellow
Evaluation TSC1__CCE (46 ; 52 ; 40 ; 34 ; 22 ;
28 ; 16 ; 10 ; 4)
VCM 4276F NORD Error 13 received network data in error wrong link between Current gear Yellow
and gear number rangex (x=1..5)
VCM 42770 NORD Error 0D out of calibration wrong ratio between Vehicle speed Yellow
and output shaft speed or bad EOL
parameter
VCM 42771 NORD Error 12 Data valid but below normal operational bad value inside the limitation Yellow
range MAPS or interpolation error
VCM 42772 NORD Error 02 Data erratic, intermittent or incorrect wrong EOL parameters division by Yellow
(application Eltrac) zero due to vehicle speed equal to
0Km/h
VCM 42773 NORD Error 0B Root cause not known Software initializing a bad value on Yellow
output.
VCM 42774 VIM - Vehicle information module 00 Data valid but above normal operational filtered MTCO vehicle speed greater Yellow
range - most severe level than Brake speed of a certain EOL
km/h threshold
VCM 42774 VIM - Vehicle information module 01 Data valid but below normal operational filtered MTCO vehicle speed lower Yellow
range - most severe level than Brake speed of a certain EOL
km/h threshold
VCM 42774 VIM - Vehicle information module 02 Data erratic, intermittent or incorrect Totally missing vehicle speed Yellow
VCM 42774 VIM - Vehicle information module 0B Root cause not known Missing TCO1 official information, Yellow
but a recovery speed is available
VCM 42774 VIM - Vehicle information module 12 Data valid but below normal operating MTCO vehicle speed greater than Yellow
range - moderately severe level EOL thr Km/h
VCM 42775 VIM - Vehicle information module 02 Data erratic, intermittent or incorrect Engine speed totally missing Yellow
VCM 42775 VIM - Vehicle information module 0B Root cause not known Engine speed missing but replaced Yellow
VCM 42775 VIM - Vehicle information module 13 Received network data in error Engine speed over range Yellow
VCM 42776 VIM - Vehicle information module 02 Data erratic, intermittent or incorrect Engine speed totally missing Yellow
VCM 42776 VIM - Vehicle information module 0B Root cause not known Engine speed missing but replaced Yellow

Bianca Andreana Trakker E4 Errors list Print Date: 21.11.2021

ELTRAC ET-TN-445-87 - Trakker E4 Error Codes Page 29 of 30

ECU SPN Fau ltC om p onent D

es
crip
tio
n F MI F M I Co m m e nt L
amps
tat
u s M
ILL
amp
Na
m e [Hex] [
H e
x] D esc ription
VCM 42776 VIM - Vehicle information module 13 Received network data in error Engine speed over range Yellow
VCM 42777 (A)CC Output interface 00 Data valid but above normal operational Positive torque request inside the Yellow
range - most severe level TSC1_ER_CC torque request from
(A)CC core controller.
VCM 42777 (A)CC Output interface 01 Data valid but below normal operational Negative torque request inside the Yellow
range - most severe level TSC1_E_SL torque limitation
request from (A)CC core controller.
VCM 42777 (A)CC Output interface 11 Data valid but below normal operating Negative torque request inside the Yellow
range - least severe level TSC1_E_CC torque request from
(A)CC core controller.
VCM 42778 EM interface 01 Data valid but below normal operational Torque limit requested from EM is Yellow
range - most severe level under a plausible threshold (0%).
VCM 42778 EM interface 02 Data erratic, intermittent or incorrect Engine speed higher limit requested Yellow
from EM is over a plausible window.
VCM 42778 EM interface 0C Bad intelligent device or component Engine speed lower limit requested Yellow
from EM is greater than Engine
speed higher limit requested from
EM.
VCM 42778 EM interface 10 Data valid but above normal operating Engine speed requested from EM is Yellow
range - moderately severe level over a plausible window.
VCM 42778 EM interface 11 Data valid but below normal operating Engine speed lower limit requested Yellow
range - least severe level from EM is over a plausible window.
VCM 42779 Low Idle Control Module 0B Failure mode not identificable Low Idle Speed Setpoint Value is Yellow
not within a valid range
VCM 4277A High Idle Control Module 0B Failure mode not identificable Low Idle Speed Setpoint Value is Yellow
not within a valid range
VCM 4277B Intermediate Speed Control Module 0B Failure mode not identificable Low Idle Speed Setpoint Value is Yellow
not within a valid range
VCM 4277C Cruise Control Buttons Interface Module 02 Data erratic, intermittent or incorrect Cruise Control Buttons Interface Off
Hardware problems [the same of
Digital Inputs 5, 6, 7, 8. For this
reason the error message sending
flag is set to 0b (disabled)]
VCM 4277D Cruise Control Buttons Interface Module 02 Data erratic, intermittent or incorrect Cruise Control Buttons Interface Yellow
Hardware not plausible conditions
[for SET+ & SET- (heavy internal),
OFF & RESUME (medium internal)]
VCM 4277D Cruise Control Buttons Interface Module 0B Failure mode not identificable Cruise Control Buttons Interface Off
(wrong command sent) [the error
message sending flag is set to 0b
(disabled)]
VCM 4277D Cruise Control Buttons Interface Module 0C bad intelligent device or component Cruise Control Buttons Interface Yellow
(stuck problems)
VCM 4277E Cruise Control Buttons Interface Module 02 Data erratic, intermittent or incorrect Cruise Control Buttons Interface Off
(blocked buttons)
VCM 4277F Cruise Control Buttons Interface Module 02 Data erratic, intermittent or incorrect Cruise Control Buttons Interface Yellow
(stuck of FPSL activation button;
see the Digital Input 3)
VCM 42780 Cruise Control Buttons Interface Module 0B Failure mode not identificable Cruise Control Input Interface Yellow
('Vehicle Speed Limit'output is not
within a valid range)[the error
message sending flag is set to 0b
(disabled)]
VCM 42781 Cruise Control Buttons Interface Module 0B Failure mode not identificable Cruise Control Input Interface ('Set Yellow
Speed (A)CC'output is not within a
valid range)[the error message
sending flag is set to 0b (disabled)]
VCM 42781 Cruise Control Buttons Interface Module 0C bad intelligent device or component Cruise Control Input Interface (logic Yellow
not plausible conditions)
VCM 42782 Power Take Off Module 0B Failure mode not identificable Power Take Off Message (‘Power Off
Take Off Speed’ or ‘Power Takeoff
Set Speed’ is not within a valid
range)
VCM 42783 Cruise Control Vehicle Speede Module 0B Failure mode not identificable Cruise Control Vehicle Speed Off
Message (‘Cruise Control Set
Speed’ or ‘Wheel based vehicle
speed’) is not within a valid range)
VCM 42784 Gear Ratio calculation 0C bad intelligent device or component Incoherent value of the ratio of Yellow
engine speed and tachograph
output shaft speed
VCM 42785 Torque limit 02 Data erratic, intermittent or incorrect Incoherent value during the Off
calculation of
%load@currEngSpeed
VCM 42788 Driveability 02 Data erratic, intermittent or incorrect Incoherent value of accelerator Yellow
pedal and engine speed for
MIN-MAX
VCM 42788 Driveability 0E special instructions Incoherent value of engine speed Yellow
for ALL SPEED
VCM 42789 Engine Brake Management 02 Data erratic, intermittent or incorrect TSC1_TER detection Off
VCM 4278A Engine Brake Management 02 Data erratic, intermittent or incorrect TSC1_AER detection Off
VCM 4278B Engine Brake Management 02 Data erratic, intermittent or incorrect TSC1_DER detection Off
VCM 4278C Engine Brake Management 02 Data erratic, intermittent or incorrect TSC1_PER on VDB detection Off
VCM 4278D Engine Brake Management 02 Data erratic, intermittent or incorrect TSC1_PER on ICB detection Off
VCM 4278E Engine Brake Management 02 Data erratic, intermittent or incorrect TSC1_CCER detection Off
VCM 4278F Engine Brake Management 02 Data erratic, intermittent or incorrect When VCM receives TSC1_PER Off
both on ICB and VDB
VCM 42790 Intarder Brake Management 02 Data erratic, intermittent or incorrect TSC1_ADR detection Off
VCM 42791 Intarder Brake Management 02 Data erratic, intermittent or incorrect TSC1_CCDR detection Off
VCM 42792 Powertrain and Brake request 0B Root cause not known One or more of internal error Off
Evaluation relative to TSC1_EME are active.
VCM 42793 VIM - Vehicle information module 02 Data erratic, intermittent or incorrect Brake light activation error. Yellow
VCM 42794 Engine Brake Management 02 Data erratic, intermittent or incorrect TSC1_TXR detection Off
VCM 42795 Engine Brake Management 02 Data erratic, intermittent or incorrect TSC1_AXR Off
VCM 42796 Engine Brake Management 02 Data erratic, intermittent or incorrect TSC1_EMER detection Off
VCM 42797 EU2LeverInterface 02 Data erratic, intermittent or incorrect Yellow
(application Eltrac)
VCM 42797 EU2LeverInterface 09 abnormal update rate Gear Up request on the message Off
SWI2BC in timeout or in error
VCM 42798 EU2LeverInterface 02 Data erratic, intermittent or incorrect Gear Down request stucked Yellow
(request continuously
active for more than an EOL
threshold)
VCM 42798 EU2LeverInterface 09 abnormal update rate Gear Down request on the message Off
SWI2BC in timeout or in error
VCM 42799 EU2LeverInterface 02 Data erratic, intermittent or incorrect Neutral request stucked (request Yellow
continuously
active for more than an EOL
threshold)
VCM 4279A EU2LeverInterface 02 Data erratic, intermittent or incorrect Drive Forward / Drive Forward Yellow
Manoeuvring button stucked
(request continuously
active for more than an EOL
threshold)
VCM 4279A EU2LeverInterface 0C bad intelligent device or component Not plausibity detected between the Yellow
two redundant switches of the Drive
Forward / Drive Forward
manoeuvring button
VCM 4279B EU2LeverInterface 02 Data erratic, intermittent or incorrect Drive Forward / Drive Forward Yellow
Manoeuvring button stucked
(request continuously
active for more than an EOL
threshold)
VCM 4279B EU2LeverInterface 0C bad intelligent device or component Not plausibity detected between the Yellow
two redundant switches of the Drive
Forward / Drive Forward
manoeuvring button
VCM 4279C Service Brake Eval 0C bad intelligent device or component Primary brake switch and Red
secondary switch not plausible
VCM 4279D Driver Intarder Brake 0C bad intelligent device or component Plausibility check on the Intarder Yellow
brake lever
VCM 4279E Engine Fan 0C bad intelligent device or component Plausibility check between the 18 Yellow
and the 22 bar pressure switch
VCM 4279F Driver Engine Brake 0C bad intelligent device or component Plausibility check on the Engine Yellow
brake lever
VCM 427C0 Vehicle Data Bus (instrument cluster) 01 Abnormal update rate not supported: ServiceInfo Timeout Off
(VDB)
VCM 427C0 Vehicle Data Bus (instrument cluster) 02 abnormal update rate ACC2 timeout (VDB) Yellow
VCM 427C0 Vehicle Data Bus (instrument cluster) 03 abnormal update rate DM1_IC timeout (VDB) Off
VCM 427C0 Vehicle Data Bus (instrument cluster) 04 abnormal update rate IC2BC timeout (VDB) Off
VCM 427C8 Vehicle Data Bus 0A abnormal rate of change VDB_limitation Yellow
VCM 427C8 Vehicle Data Bus 13 received network data in error VDB bus off Off
VCM 427C9 Vehicle Data Bus (brake controller) 01 Abnormal update rate EBC1 timeout Off
VCM 427C9 Vehicle Data Bus (brake controller) 02 Abnormal update rate EBC2 timeout Off
VCM 427C9 Vehicle Data Bus (brake controller) 03 Abnormal update rate TSC1_AE timeout Off
VCM 427C9 Vehicle Data Bus (brake controller) 04 Abnormal update rate TSC1_AER timeout Off
VCM 427C9 Vehicle Data Bus (brake controller) 05 Abnormal update rate TSC1_ADR timeout Off
VCM 427C9 Vehicle Data Bus (brake controller) 06 Abnormal update rate EBC5 timeout Off

Bianca Andreana Trakker E4 Errors list Print Date: 21.11.2021

ELTRAC ET-TN-445-87 - Trakker E4 Error Codes Page 30 of 30

ECU S P
N F
aultC
omp
one
nt D
es
crip
tio
n F MI F M I C
omm
en
t L
amps
tat
u s M
ILL
amp
Na
m e [
H e
x] [
H e
x] De sc ript
ion
VCM 427C9 Vehicle Data Bus (brake controller) 07 Abnormal update rate VDC1 timeout Off
VCM 427C9 Vehicle Data Bus (brake controller) 08 Abnormal update rate VDC2 timeout Off
VCM 427C9 Vehicle Data Bus (brake controller) 09 Abnormal update rate CVW timeout Off
VCM 427C9 Vehicle Data Bus (brake controller) 0A Abnormal update rate HRW timeout Off
VCM 427C9 Vehicle Data Bus (brake controller) 0B Abnormal update rate TC1_EBS timeout Off
VCM 427C9 Vehicle Data Bus (brake controller) 0C Abnormal update rate TSC1_AXR timeout Off
VCM 427CA Vehicle Data Bus (transmission 01 Abnormal update rate ETC1 timeout (VDB) Off
controller)
VCM 427CA Vehicle Data Bus (transmission 02 abnormal update rate ETC2 timeout (VDB) Off
controller)
VCM 427CA Vehicle Data Bus (transmission 03 abnormal update rate TSC1_TE timeout (VDB) Off
controller)
VCM 427CA Vehicle Data Bus (transmission 04 abnormal update rate TSC1_TER timeout (VDB) Off
controller)
VCM 427CA Vehicle Data Bus (transmission 05 abnormal update rate ETC8 timeout (VDB) Off
controller)
VCM 427CA Vehicle Data Bus (transmission 06 abnormal update rate TSC1_TXR timeout (VDB) Off
controller)
VCM 427CA Vehicle Data Bus (transmission 07 abnormal update rate ETC7 timeout (VDB) Off
controller)
VCM 427CA Vehicle Data Bus (transmission 08 abnormal update rate not supported: ETC5 timeout (VDB) Off
controller)
VCM 427CA Vehicle Data Bus (transmission 09 abnormal update rate TC_BC timeout (VDB) Off
controller)
VCM 427CA Vehicle Data Bus (transmission 0A abnormal update rate CVW_GB timeout (VDB) Off
controller)
VCM 427CB Vehicle Data Bus (body controller) 01 Abnormal update rate not supported: AIR1 timeout (VDB) Off
VCM 427CB Vehicle Data Bus (body controller) 02 abnormal update rate TSC1_PEV timeout (VDB) Off
VCM 427CB Vehicle Data Bus (body controller) 03 abnormal update rate TSC1_PERV timeout (VDB) Off
VCM 427CB Vehicle Data Bus (body controller) 04 abnormal update rate TSC1_EME timeout (VDB) Off
VCM 427CB Vehicle Data Bus (body controller) 05 abnormal update rate TSC1_EMER timeout (VDB) Off
VCM 427CB Vehicle Data Bus (body controller) 06 abnormal update rate BC2EDC timeout (VDB) Off
VCM 427CB Vehicle Data Bus (body controller) 07 abnormal update rate AMB_COND_IBC timeout (VDB) Off
VCM 427CB Vehicle Data Bus (body controller) 08 abnormal update rate BCAO1 timeout (VDB) Off
VCM 427CB Vehicle Data Bus (body controller) 09 abnormal update rate BCAO2 timeout (VDB) Off
VCM 427CB Vehicle Data Bus (body controller) 0B abnormal update rate BCAO3 timeout (VDB) Off
VCM 427CB Vehicle Data Bus (body controller) 0A abnormal update rate Dash_display timeout (VDB) Off
VCM 427CB Vehicle Data Bus (body controller) 13 abnormal update rate not supported: Other Body Off
controller timeout (VDB)
VCM 427CC Vehicle Data Bus (driveline retarder) 01 Abnormal update rate ERC1_DR timeout (VDB) Off
VCM 427CC Vehicle Data Bus (driveline retarder) 02 abnormal update rate TSC1_DE timeout (VDB) Off
VCM 427CC Vehicle Data Bus (driveline retarder) 03 abnormal update rate TSC1_DER timeout (VDB) Off
VCM 427CC Vehicle Data Bus (driveline retarder) 04 abnormal update rate BAM_DR / MPM_DR timeout Off
(VDB)
VCM 427CD Vehicle Data Bus (tachograph) 01 Abnormal update rate TCO1 timeout (VDB) Off
VCM 427CD Vehicle Data Bus (tachograph) 02 abnormal update rate VDHR timeout (VDB) Off
VCM 427CD Vehicle Data Bus (tachograph) 03 abnormal update rate Time date timeout (VDB) Off
VCM 427CE Vehicle Data Bus (ACC sensor) 01 Abnormal update rate ACC_SI timeout (VDB) Yellow
VCM 427CE Vehicle Data Bus (ACC sensor) 02 abnormal update rate DM1_ACCSens timeout (VDB) Off
VCM 427CF Vehicle Data Bus (expansion module) 01 Abnormal update rate EM2VCM timeout (VDB) Off
VCM 427CF Vehicle Data Bus (expansion module) 02 abnormal update rate TC1_EM timeout (VDB) Off
VCM 427CF Vehicle Data Bus (expansion module) 03 abnormal update rate EM_CMD timeout (VDB) Off
VCM 427CF Vehicle Data Bus (expansion module) 04 abnormal update rate TSC1_PE timeout (VDB) Off
VCM 427CF Vehicle Data Bus (expansion module) 05 abnormal update rate TSC1_PER timeout (VDB) Off
VCM 427CF Vehicle Data Bus (expansion module) 06 abnormal update rate PTO_Status timeout (VDB) Off
VCM 427CF Vehicle Data Bus (expansion module) 07 abnormal update rate EM2BC (VDB) Off
VCM 427D0 Vehicle Data Bus (steering wheel 09 abnormal update rate SWI2BC timeout (VDB) Off
interface)
VCM 427D1 Vehicle Data Bus (suspension) 06 abnormal update rate not supported: ASC1_A timeout Off
(VDB)
VCM 427D1 Vehicle Data Bus (suspension) 07 abnormal update rate not supported: ASC3_A timeout Off
(VDB)
VCM 427D1 Vehicle Data Bus (suspension) 08 abnormal update rate not supported: ASC4_A timeout Off
(VDB)
VCM 427D1 Vehicle Data Bus (suspension) 09 abnormal update rate not supported: Vehicle_Weight Off
timeout (VDB)
VCM 427D2 Engine Control Bus 13 received network data in error ECB bus off Yellow
VCM 427D2 Engine Control Bus 0A abnormal rate of change ECB limitation Yellow
VCM 427D3 Engine Control Bus (engine) 01 Abnormal update rate EEC1 timeout (ECB) Yellow
VCM 427D3 Engine Control Bus (engine) 02 abnormal update rate EEC2 timeout (ECB) Off
VCM 427D3 Engine Control Bus (engine) 03 abnormal update rate EEC3 timeout (ECB) Off
VCM 427D3 Engine Control Bus (engine) 04 abnormal update rate ENG_TEMP timeout (ECB) Off
VCM 427D3 Engine Control Bus (engine) 05 abnormal update rate AMB_COND_E timeout (ECB) Off
VCM 427D3 Engine Control Bus (engine) 06 abnormal update rate INLET_COND timeout (ECB) Off
VCM 427D3 Engine Control Bus (engine) 07 abnormal update rate EDC2BC timeout (ECB) Off
VCM 427D3 Engine Control Bus (engine) 08 abnormal update rate Eng_Fld_Lev_Press timeout (ECB) Off
VCM 427D3 Engine Control Bus (engine) 09 abnormal update rate ELT_POWER timeout (ECB) Off
VCM 427D3 Engine Control Bus (engine) 0A abnormal update rate Shutdown timeout (ECB) Off
VCM 427D3 Engine Control Bus (engine) 0B abnormal update rate Fuel_Economy timeout (ECB) Off
VCM 427D3 Engine Control Bus (engine) 0C abnormal update rate Fuel_Cons timeout (ECB) Off
VCM 427D3 Engine Control Bus (engine) 0D abnormal update rate not supported: Eng_Hours_Rev Off
timeout (ECB)
VCM 427D3 Engine Control Bus (engine) 0E abnormal update rate BAM_Eng_Conf / MPM_Eng_Conf Off
timeout (ECB)
VCM 427D3 Engine Control Bus (engine) 0F abnormal update rate FAN_Drive timeout (ECB) Off
VCM 427D4 Engine Control Bus (engine retarder) 01 Abnormal update rate BAM_ret_conf / MPM_ret_conf Off
timeout (ECB)
VCM 427D4 Engine Control Bus (engine retarder) 02 abnormal update rate ERC1_ER timeout (ECB) Off
VCM 427D5 Engine Control Bus (exhaust emission 09 abnormal update rate SCR_status2 timeout (ECB) Yellow
controller - UDS)
VCM 427DC Instrument Cluster Bus 13 received network data in error ICB bus off Off
VCM 427DC Instrument Cluster Bus 0A abnormal rate of change ICB limitation Yellow
VCM 427DD Instrument Cluster Bus (body computer) 01 Abnormal update rate BC_Status1 timeout (ICB) Off
VCM 427DD Instrument Cluster Bus (body computer) 02 abnormal update rate BC_Status2 timeout (ICB) Off
VCM 427DD Instrument Cluster Bus (body computer) 03 abnormal update rate BC_Status3 timeout (ICB) Off
VCM 427DD Instrument Cluster Bus (body computer) 04 abnormal update rate RF_Status1 timeout (ICB) Off
VCM 427DD Instrument Cluster Bus (body computer) 05 abnormal update rate BC2IC timeout (ICB) Off
VCM 427DD Instrument Cluster Bus (body computer) 06 abnormal update rate PTO_Status timeout (ICB) Off
VCM 427DD Instrument Cluster Bus (body computer) 07 abnormal update rate FF_Status1 timeout (ICB) Off
VCM 427DD Instrument Cluster Bus (body computer) 08 abnormal update rate Trip_Total_Fuel timeout (ICB) Off
VCM 427DD Instrument Cluster Bus (body computer) 09 abnormal update rate TCO1 timeout (ICB) Off
VCM 427DE Instrument Cluster Bus (steering wheel 01 Abnormal update rate SWI2BC timeout (ICB) Off
interface)
VCM 427DE Instrument Cluster Bus (steering wheel 02 abnormal update rate not supported: SWI2IC timeout Off
interface) (ICB)
VCM 427DF Instrument Cluster Bus (expansion 01 Abnormal update rate not supported: EM2VCM timeout Off
module) (ICB)
VCM 427DF Instrument Cluster Bus (expansion 02 abnormal update rate not supported: TC1_EM timeout Off
module) (ICB)
VCM 427DF Instrument Cluster Bus (expansion 03 abnormal update rate not supported: EM_CMD timeout Off
module) (ICB)
VCM 427DF Instrument Cluster Bus (expansion 04 abnormal update rate not supported: TSC1_PE timeout Off
module) (ICB)
VCM 427DF Instrument Cluster Bus (expansion 05 abnormal update rate not supported: TSC1_PER timeout Off
module) (ICB)
VCM 427DF Instrument Cluster Bus (expansion 06 abnormal update rate not supported: EM2BC timeout Off
module) (ICB)
VCM 427DF Instrument Cluster Bus (expansion 07 abnormal update rate not supported: CTL timeout (ICB) Off
module)
VCM 427DF Instrument Cluster Bus (expansion 08 abnormal update rate not supported: ASC2 timeout (ICB) Off
module)
VCM 427E2 Instrument Cluster Bus (instrument 01 Abnormal update rate IC2BC timeout (ICB) Off
cluster)
VCM 427E2 Instrument Cluster Bus (instrument 02 abnormal update rate ACC2 timeout (ICB) Yellow
cluster)
VCM 427E3 Instrument Cluster Bus (ACC sensor) 01 Abnormal update rate ACC_SI timeout (ICB) Off
VCM 427E3 Instrument Cluster Bus (ACC sensor) 02 abnormal update rate DM1_ACCSens timeout (ICB) Yellow
VCM 427E6 FMS Bus 13 received network data in error FMS bus off Off
VCM 427E6 FMS Bus 0A abnormal rate of change FMS limitation Yellow

Bianca Andreana Trakker E4 Errors list Print Date: 21.11.2021