10/6/2024

CSEN 116
Engineering Drawing I

Drawing Layout
Evans Khadambi Luyali

Drawing layout - components Drawing layout - components

Revision Table Revision Table
A revision table is normally located in A revision table is normally located in
the upper right of the drawing frame,
or at the bottom on the left side of the Title Block Revision Table the upper right of the drawing frame,
or at the bottom on the left side of the
title block.
All modifications to the drawing should
be documented here.
A revision
The title block is normally placedtable is bottom
in the normally right of the
title block.
All modifications to the drawing should
be documented here.

Material or Parts List (Schedule) drawing frame, andlocated

it shouldincontain
the upper right of the
the following Material or Parts List (Schedule)
If the drawing contains a number of parts, or if If the drawing contains a number of parts, or if
it is an assembly drawing, a tabulated parts list information: Material or Parts List (Schedule)
drawing frame, or at the bottom it is an assembly drawing, a tabulated parts list

- the name ofIfthethe drawing contains a number of parts, or if it is an

is attached to the bottom right of the drawing is attached to the bottom right of the drawing
frame, just above the title block.
company
ondrawing, or organization
the left side ofparts
thelisttitle block.to the
frame, just above the title block.
The parts list should give the following
assembly a tabulated is attached The parts list should give the following
information:
- the title of the drawing information:
•the part number
•the part name
•the quantity required
bottom
- the drawingblock.
All modifications
right to the
of the drawing frame,
number, which is generally a unique filing
drawing
just above the title •the part number
•the part name
•the quantity required
•material specifications
•the drawing number of each individual part identifier should be documented here.
The parts list should give the following information:
•material specifications
•the drawing number of each individual part
•other applicable information Zoning •other applicable information
When the parts list is very large a separate
- the scale •the part number When the parts list is very large a separate
drawing sheet may be used for the parts list
A drawing may be•the dividedpart name up into a grid using letters drawing sheet may be used for the parts list
alone.
- the angle
and numbers. When of projection used, iteither first orinside
alone.
third, generally
•thezoning
quantityisrequired used is located
Title Block
The title block is normally placed in the bottom right of the drawing frame, and
shown
the drawingA
symbolically
Zoning
frame.
drawing may be•material
divided up into a grid
Title Block
specifications
The title block is normally placed in the bottom right of the drawing frame, and
it should contain the following information:
- the
Zoning signature
allows easy •theor initials
using letters and numbers. When zoning is
thedrawing
references of- thethe
frame. number
to name ofdraftsman,
it should contain the following information:
various of each orindividual checker, part
of the drawingparts of the
- the name of the company or organization used it is located inside drawing the company organization
- the title of the drawing - the title
approving officer, and a issuing officer, with C7.the respective
Zoning allows easy references to various
- the drawing number, which is generally a unique filing identifier
- the scale drawing byparts
referencing
of the drawing
coordinate
•other
aapplicable
by referencing
such as C7. coordinate information
- the drawing
- the scale such as
number, which is generally a unique filing identifier

- the angle of projection used, either first or third, generally shown symbolically dates When the parts- thelist angleisofvery large
projection a separate
used, either drawing
first or third, generally sheet
shown symbolically
- the signature or initials of the draftsman, checker, approving officer, and issuing - the signature or initials of the draftsman, checker, approving officer, and issuing
may be used for the withparts list dates
alone.
officer, with the respective dates
-other information as required
3 -other information as required officer, the respective
-other information as required
4

Drawing layout – Title block Drawing layout Sample

• A title block is the form on which the actual

drawing is a section.
• It includes the border and the various sections for
providing quality, administrative and technical
information.
• The title block is vital as it includes all the
information which enables the drawing to be
interpreted, identified and archived.
• E.g.

1
 10/6/2024

Drawing layout - Sample Drawing layout for CSEN 116 Assignments

DRAWN BY: DEPARTMENT OF CIVIL AND STRUCTURAL ENGINEERING

1. FIGURED DIMENSIONS ONLY TO BE TAKEN FROM THIS DRAWING A N OTHER CSEN 116 ENGINEERING DRAWING I
CSE/000/00
DATE: 00/10.2024

Drawing layout for CSEN 116 Assignments

At the next session

BELOW ARE SUGGESTED DIMENSIONS FOR THE TITLE
BLOCK

ANY OTHER DIMENSIONS MAY BE USED SO LONG AS

THE LAYOUT IS PRESENTABLE
Geometric Construction
__ 90 200

DRAWN BY: DEPARTMENT OF CIVIL AND STRUCTURAL ENGINEERING

1. FIGURED DIMENSIONS ONLY TO BE TAKEN FROM THIS DRAWING A N OTHER CSEN 116 ENGINEERING DRAWING I
20

CSE/000/00
DATE: 00/10.2024
50

20
10

10