DL121/D Rev.

6, Jan-2000

LS TTL Data
ON Semiconductor
Formerly a Division of Motorola

LS TTL Data
Formerly Titled FAST and LS TTL Data

Please Note: As ON Semiconductor has exited the FAST TTL business, all FAST data sheets have been removed from this publication. For further assistance, please contact your local ON Semiconductor representative.

DL121/D Rev. 6, Jan2000

SCILLC, 2000 Previous Edition 1992 All Rights Reserved

ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Typical parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including Typicals must be validated for each customer application by customers technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer.

PUBLICATION ORDERING INFORMATION

North America Literature Fulfillment: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 3036752175 or 8003443860 Toll Free USA/Canada Fax: 3036752176 or 8003443867 Toll Free USA/Canada Email: [email protected] N. American Technical Support: 8002829855 Toll Free USA/Canada EUROPE: LDC for ON Semiconductor European Support German Phone: (+1) 3033087140 (MF 2:30pm to 5:00pm Munich Time) Email: [email protected] French Phone: (+1) 3033087141 (MF 2:30pm to 5:00pm Toulouse Time) Email: [email protected] English Phone: (+1) 3033087142 (MF 1:30pm to 5:00pm UK Time) Email: [email protected] ASIA/PACIFIC: LDC for ON Semiconductor Asia Support Phone: 3036752121 (TueFri 9:00am to 1:00pm, Hong Kong Time) Toll Free from Hong Kong 80044223781 Email: [email protected] JAPAN: ON Semiconductor, Japan Customer Focus Center 4321 NishiGotanda, Shinagawaku, Tokyo, Japan 1418549 Phone: 81357402745 Email: [email protected] Fax Response Line: 3036752167 8003443810 Toll Free USA/Canada ON Semiconductor Website: http://onsemi.com For additional information, please contact your local Sales Representative.

http://onsemi.com
2

CONTENTS
Page CHAPTER 1 SELECTION INFORMATION, LS TTL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 CHAPTER 2 CIRCUIT CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Family Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 LS TTL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Circuit Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Input Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Input Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Output Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Output Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 AC Switching Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 LS ESD Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 CHAPTER 3 DESIGN CONSIDERATIONS, TESTING AND APPLICATIONS ASSISTANCE FORM . . . . . . DESIGN CONSIDERATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Noise Immunity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Power Consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fan-In and Fan-Out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Wired-OR Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Unused Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Input Capacitance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Line Driving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Output Rise and Fall Times . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Interconnection Delays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DEFINITION OF SYMBOLS AND TERMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Currents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Voltages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AC Switching Parameters and Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TESTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DC Test Circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AC Test Circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . APPLICATIONS ASSISTANCE FORM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 16 16 16 16 18 18 18 18 19 19 20 21 21 21 22 24 24 25 27

CHAPTER 4 DATA SHEETS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 CHAPTER 5 RELIABILITY DATA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 259 RAP Reliability Audit Program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 261 CHAPTER 6 PACKAGE INFORMATION INCLUDING SURFACE MOUNT . . . . . . . . . . . . . . . . . . . . . . . . . . Surface Mount Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Tape and Reel Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Package Outlines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Worldwide Sales Offices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Document Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 263 265 266 267 269 270

http://onsemi.com
3

Device SN74LS00 SN74LS04 SN74LS05 SN74LS08 SN74LS14 SN74LS32 SN74LS38 SN74LS42 SN74LS47 SN74LS74A SN74LS76A SN74LS85 SN74LS86 SN74LS109A SN74LS122 SN74LS125A SN74LS132 SN74LS138 SN74LS139 SN74LS145 SN74LS147 SN74LS151 SN74LS153 SN74LS156 SN74LS157 SN74LS161A SN74LS164 SN74LS165 SN74LS166 SN74LS174 SN74LS175 SN74LS193 SN74LS194A SN74LS195A SN74LS221 SN74LS240 SN74LS245 SN74LS247 SN74LS251 SN74LS253 SN74LS257B SN74LS259 SN74LS260 SN74LS273 SN74LS280 SN74LS283 SN74LS298 SN74LS299 SN74LS365A SN74LS373 SN74LS377 SN74LS393 SN74LS541 SN74LS640 SN74LS670 SN74LS682

Description Quad 2-Input NAND Gate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hex Inverter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hex Inverter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Quad 2-Input AND Gate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Schmitt Triggers Dual Gate/Hex Inverter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Quad 2-Input OR Gate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Quad 2-Input NAND Buffer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . One-of-Ten Decoder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . BCD to 7-Segment Decoder/Driver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Dual DType Positive EdgeTriggered Flip-Flop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Dual JK Flip-Flop with Set and Clear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-Bit Magnitude Comparator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Quad 2Input Exclusive OR Gate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Dual JK Positive Edge-Triggered Flip-Flop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Retriggerable Monostable Multivibrators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Quad 3-State Buffers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Quad 2-Input Schmitt Trigger NAND Gate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-of-8 Decoder/Demultiplexer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Dual 1-of-4 Decoder/Demultiplexer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-of-10 Decoder/Driver Open-Collector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-Lineto4Line and 8-Lineto3Line Priority Encoders . . . . . . . . . . . . . . . . . . . . . . . . . 8-Input Multiplexer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Dual 4-Input Multiplexer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Dual 1-of-4 Decoder/Demultiplexer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Quad 2-Input Multiplexer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . BCD Decade Counters/4Bit Binary Counters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Serial-In ParallelOut Shift Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-Bit Parallel-To-Serial Shift Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-Bit Shift Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hex D Flip-Flop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Quad D Flip-Flop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Presettable 4Bit Binary Up/Down Counter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-Bit Bidirectional Universal Shift Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Universal 4-Bit Shift Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Dual Monostable Multivibrators with SchmittTrigger Inputs . . . . . . . . . . . . . . . . . . . . . . . . . Octal Buffer/Line Driver with 3-State Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Octal Bus Transceiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . BCDtoSevenSegment Decoders/Drivers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-Input Multiplexer with 3-State Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Dual 4-Input Multiplexer with 3-State Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Quad 2-Input Multiplexer with 3-State Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-Bit Addressable Latch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Dual 5-Input NOR Gate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Octal D Flip-Flop with Clear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-Bit Odd/Even Parity Generators/Checkers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-Bit Binary Full Adder with Fast Carry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Quad 2-Input Multiplexer with Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-Bit Shift/Storage Register with 3-State Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-State Hex Buffers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Octal Transparent Latch with 3-State Outputs; Octal D-Type Flip-Flop with 3-State Output Octal D Flip-Flop with Enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Dual 4-Stage Binary Counter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Octal Buffer/Line Driver with 3State Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Octal Bus Transceivers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 x 4 Register File with 3-State Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-Bit Magnitude Comparators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . http://onsemi.com
4

Page 30 32 34 36 38 41 43 45 49 53 57 59 64 66 69 78 81 84 89 93 97 102 106 110 114 118 124 129 134 139 143 147 153 158 163 169 173 175 180 185 189 194 199 201 205 207 212 217 223 226 232 236 241 244 248 253

CHAPTER 1 Selection Information LS TTL

http://onsemi.com
5

GENERAL INFORMATION
TTL in Perspective Since its introduction, TTL has become the most popular form of digital logic. It has evolved from the original gold-doped saturated 7400 logic, to Schottky-Clamped logic, and finally to the modern advanced families of TTL logic. The popularity of these TTL families stem from their ease of use, low cost, medium-to-high speed operation, and good output drive capability. Low Power Schottky (LSTTL) was the industry standard logic family for many years. Since its inception, several more modern families have come out, with equal or better TTL Family Comparisons
General Characteristics for Schottky TTL Logic (All Maximum Ratings)
Characteristic Operating Voltage Range Operating Temperature Range Input Current IIN Output Drive Standard Output IOH IOL ISC IOH Buffer Output IOL ISC Symbol VCC TA IIH IIL 74LSxxx 5 5% 0 to 70 20 400 0.4 8.0 20 to 100 15 24 40 to 225 Unit Vdc C A mA mA mA mA mA mA

performance. We therefore recommend the VHC, High Speed and FACT products for all new 5.0 Volt designs. Further improvements in power reduction can be achieved using the LVX, LCX or VCX running at 3.3 Volts. Improvements in electrostatic discharge susceptibility in these newer CMOS products now make them the obviate the need for LSTTL in new designs. The VHC family is faster and lower power with similar drive characteristics compared to LSTTL. We highly recommend new designs use one or more of these CMOS families.

Speed/Power Characteristics for Schottky TTL Logic(1) (All Typical Ratings)

Characteristic Quiescent Supply Current/Gate Power/Gate (Quiescent) Propagation Delay Speed Power Product Clock Frequency (D-F/F) Clock Frequency (Counter) Symbol IG PG tp fmax fmax Typ 0.4 2.0 9.0 18 33 40 Unit mA mW ns pJ MHz MHz

NOTES: 1. Specifications are shown for the following conditions: NOTES: 1. a) VCC = 5.0 Vdc (AC), NOTES: 1. b) TA = 25C, NOTES: 1. c) CL = 15 pF.

http://onsemi.com
6

Functional Selection
Abbreviations
S A B = Synchronous = Asynchronous = Both Synchronous and Asynchronous

2S = 2-State Output 3S = 3-State Output OC = Open-Collector Output

Inverters
Description Hex Type of Output 2S OC No. 04 05

Multiplexers
Description Quad 2-to-1, Non-Inverting Quad 2-to-1, Inverting Dual 4-to-1, Non-Inverting Type of Output 2S No. 08 8-to-1 Type of Output 2S 3S 3S 2S 3S 2S 3S 2S No. 157 257B 258B 153 253 151 251 298

AND Gates
Description Quad 2-Input

NAND Gates
Description Quad 2-Input Type of Output 2S No. 00

Encoders
Description 10-to-4-Line BCD 8-to-3-Line Priority Encoder Type of Output 2S 2S No. 147 148

OR Gates
Description Quad 2-Input Type of Output 2S

Register Files
No. 32 Description 4x4 Type of Output 3S No. 670

NOR Gates
Description Dual 5-Input Type of Output 2S

Decoders/Demultiplexers
No. 260 Description Dual 1-of-4 Type of Output 2S OC 2S 2S No. 139 156 138 42

Exclusive OR Gates
Description Quad 2-Input Type of Output 2S No. 86 1-of-8 1-of-10

Latches
Description No. of Bits 8 8 Type of Output 3S 2S No. 373 259

Schmitt Triggers
Description Hex, Inverting Quad 2-Input NAND Gate Type of Output 2S 2S No. 14 132 Transparent, Non-Inverting Addressable

SSI Flip-Flops
Description Dual D w/Set & Clear Dual JK w/Set & Clear Individual J, K, CP, SD, CD Inputs Dual JK w/Set & Clear Clock Edge Pos Neg Pos No. 74A 76A 109A

http://onsemi.com
7

Shift Registers
No. of Bits 8 8 8 4 4 8 Type of Output 2S 2S 2S 2S 2S 3S Mode* SR X X X X X X SL Hold X X X X Reset A A A A A No. 164 165 166 194A 195A 299

Description Serial In-Parallel Out Parallel In-Serial Out Parallel In-Parallel Out Parallel In-Parallel Out, Bidirectional
* SR = Shift Right * SL = Shift Left

X X

Asynchronous Counters Negative Edge-Triggered

Description Dual 4-Bit Binary
* The 716 and 718 are positive edge-triggered.

Load

Set

Reset X

No. 393*

Cascadable Synchronous Counters Positive Edge-Triggered

Description 4-Bit Binary Type of Output 2S 2S Load S S Reset A S No. 161A 163A

Display Decoders/Drivers with Open-Collector Outputs

Description 1-of-10 BCD-to-7 Segment No. 145* 247*

MSI Flip-Flops/Registers
Description D-Type, Non-Inverting No. of Bits 4 6 8 8 4 Type of Output 2S 2S 2S 3S 2S Set or Reset A A A Clock Enable X No. 377 174 273 374 175

D-Type, Q and Q Outputs

Arithmetic Operators
Description 4-Bit Adder No. 283

Buffers/Line Drivers
Description Quad 2-Input NAND Quad, Non-Inverting Hex, Non-Inverting P=Q X X X X P>Q X X X P<Q X No. 85 682 684 688 Hex, Inverting Octal, Non-Inverting Bus Pinout Octal, Inverting 3S 3S 3S Type of Output OC 3S 3S No. 38 125A 126A 365A 367A 368A 244 541 240

Magnitude Comparators
Description 4-Bit 8-Bit 8-Bit with Output Enable Type of Output 2S 2S 2S 2S

Transceivers Parity Generators/Checkers

Description 9-Bit Odd Even Parity Generator Checker No. 280 Description Octal, Non-Inverting Octal, Inverting Type of Output 3S OC 3S OC No. 245 641 640 642

VCOs and Multivibrators

Description Retriggerable Monostable Multivibrator Dual 122 Precision Non-Retriggerable Monostable Multivibrator No. 122 123 221

http://onsemi.com
8

CHAPTER 2 Circuit Characteristics

http://onsemi.com
9

CIRCUIT CHARACTERISTICS

FAMILY CHARACTERISTICS
LS TTL CIRCUIT FEATURES

The Low Power Schottky (LS TTL) family combines a current and power reduction improvement over standard 7400 TTL by a factor of 5. This is accomplished by using Schottky diode clamping to prevent saturation and advanced processing.

Circuit features of the LS are best understood by examining the TTL 2-input NAND gate (Figure 1). While LS has been a popular series in the past, more modern products such as VHC should be replacing LSTTL in new designs. For applications where high drive is required, FACT is an ideal choice.
110

VCC

18K A D1 D3

7.6K Q2 Q4 5K

B D2 D4 15K 2.8K

Q1 Q5 3.5K Q3

OUTPUT

Figure 1. LS00 2-Input NAND Gate

http://onsemi.com
10

INPUT CONFIGURATION

ON Semiconductor LSTTL circuits do not use the multi-emitter input structure that originally gave TTL its name. Most LS elements use a DTL type input circuit with Schottky diodes to perform the AND function, as exemplified by D3 and D4 in Figure 1. Compared to the classical multi-emitter structure, this circuit is faster and increases the input breakdown voltage. Inputs of this type are tested for leakage with an applied input voltage of 7.0 V and the input breakdown voltage is typically 15 V or more. Another input arrangement often used in LS MSI has three diodes connected as shown in Figure 2. This configuration gives a slightly higher input threshold than that of Figure 1. A third input configuration that is sometimes used in LS TTL employs a vertical PNP transistor as shown in Figure 3. This arrangement also gives a higher input threshold and has
VCC

the additional advantage of reducing the amount of current that the signal source must sink. Both the diode cluster arrangement and the PNP input configuration have breakdown voltage ratings greater than 7.0 V. All inputs are provided with clamping diodes, exemplified by D1 and D2 in Figure 1. These diodes conduct when an input signal goes negative, which limits undershoot and helps to control ringing on long signal lines following a HIGH-to-LOW transition. These diodes are intended only for the suppression of transient currents and should not be used as steady-state clamps in interface applications. A clamp current exceeding 2.0 mA and with a duration greater than 500 ns can activate a parasitic lateral NPN transistor, which in turn can steal current from internal nodes of an LS circuit and thus cause logic errors.
VCC

Figure 2. Diode Cluster Input INPUT CHARACTERISTICS

Figure 3. PNP Input

Figure 4 shows the typical input characteristics of LS. Typical transfer characteristics can be found in Figure 5 and

input threshold variation with temperature information is provided in Table 1.

5 V OUT , OUTPUT VOLTAGE (VOLTS)

0 100 LS I IN ( A) 200 300 400 TA = 25C VCC = 5 V 0 0.2 0.4 0.6 0.8 1 1.2 VIN (VOLTS) 1.4 1.6 1.8 2

TA = 25C VCC = 5 V

3 LS 2

0.5

1 1.5 VIN, INPUT VOLTAGE (VOLTS)

2.5

Figure 4. Typical Input Current versus Input Voltage

Figure 5. Typical Output versus Input Voltage Characteristic

Table 1. Typical Input Threshold Variation with Temperature

55C ALS S LS 1.8 1.5 1.2 + 25C 1.5 1.3 1.0 + 125C 1.3 1.1 0.8

http://onsemi.com
11

OUTPUT CONFIGURATION

The output circuitry of LSTTL has several features not found in conventional TTL. A few of these features are discussed below. Referring to Figure 1, the base of the pull-down output transistor Q5 is returned to ground through Q3 and a pair of resistors instead of through a simple resistor. This arrangement is called a squaring network since it squares up the transfer characteristics (Figure 5) by preventing conduction in the phase splitter Q1 until the input voltage rises high enough to allow Q1 to supply base current to Q5. The squaring network also improves the propagation delay by providing a low resistance path to discharge capacitance at the base of Q5 during turn-off. The output pull-up circuit is a 2-transistor Darlington circuit with the base of the output transistor returned through

a 5.0K resistor to the output terminals, unlike 74H and 74S where it is returned to ground which is a more power consuming configuration. This configuration allows the output to pull up to one VBE below VCC for low values of output current. Figure 6 shows the extra circuitry used to obtain the high Z condition in 3-state outputs. When the Output Enable signal is HIGH, both the phase splitter and the Darlington pull-up are turned off. In this condition the output circuitry is non-conducting, which allows the outputs of two or more such circuits to be connected together in a bus application wherein only one output is enabled at any particular time.

VCC

OUTPUT FROM LOGIC OUTPUT ENABLE ACTIVE PULLDOWN Q5

Figure 6. Typical 3-State Output Control

OUTPUT CHARACTERISTICS

Figure 7 shows the LOW-state output characteristics for LS. For LOW IOL values, the pull-down transistor is
1 V OL , OUTPUT VOLTAGE (VOLTS) TA = 25C VCC = 4.5 V LS00

clamped out of deep saturation to shorten the turn-off delay. Figure 8 shows the HIGH-state output characteristics.
1 V OL , OUTPUT VOLTAGE (VOLTS) LS240 TA = 25C VCC = 4.5 V

0.5

0.5

0 0 20 40 IOL, OUTPUT CURRENT (mA) 60

0 50 100 150 200 IOL, OUTPUT CURRENT (mA)

Figure 7. (a) Output Low Characteristic

Figure 7. (b) Output Low Characteristic

http://onsemi.com
12

4 V OH, OUTPUT VOLTAGE (VOLTS) V OH, OUTPUT VOLTAGE (VOLTS) TA = 25C VCC = 5.5 V 3

4 TA = 25C VCC = 5.5 V 3 LS240 2

2 LS00 1

50

100

150

50

100

150

200

IOH, OUTPUT CURRENT (mA)

IOH, OUTPUT CURRENT (mA)

Figure 8. (a) Output High Characteristic

Figure 8. (b) Output High Characteristic

AC SWITCHING CHARACTERISTICS

The propagation through a logic element depends on power supply voltage, ambient temperature, and output load. The effect of each of these parameters on ac propagation is shown in Figures 9 through 11. Propagation delays are specified with only one output switching, the delay through a logic-element will increase to some extent when multiple outputs switch simultaneously due to inductance internal to the IC package.
+4 t PD , PROPAGATION DELAY CHANGE (ns) VCC = 5 V CL = 15 pF LS00 +2 tPLH 0 tPHL 2

For LS TTL, limits are guaranteed at 25C, VCC = 5.0 V, and CL = 15 pF (normally, resistive load has minimal effect on propagation delay) TTL limits are guaranteed over the commercial or military temperature and supply voltage ranges and with CL = 50 pF.

+4 t PD , PROPAGATION DELAY CHANGE (ns) TA = +25C CL = 15 pF LS00 +2 tPLH 0 tPHL 2

4 75

4 25 +25 +75 TA, AMBIENT TEMPERATURE (C) +125 4.5 4.75 5 5.25 VCC, SUPPLY VOLTAGE (V) 5.5

Figure 9.

Figure 10.

http://onsemi.com
13

20 t PD , PROPAGATION DELAY (ns) VCC = 5 V TA = 25C LS00

16

12 tPLH 8 tPHL

20

40

60

80

100

CL, LOAD CAPACITANCE (pF)

*Data for Figure 11 was taken with only one output switching at a time.

Figure 11. *

ESD CHARACTERISTICS

Electrostatic Discharge (ESD) sensitivity for ON Semiconductor TTL is characterized using several methodologies (HBM, MM, CDM). It is extremely important to understand that ESD sensitivity values alone are not sufficient when comparing devices. In an attempt to reduce correlation problems between various pieces of test equipment, all of which meet Mil-Std-883C requirements, tester specific information as well as actual device ESD

hardness levels are given in controlled documents and are available upon request. The continuing improvements of ESD sensitivity through redesigns of ON Semiconductor TTL has resulted in minimum ESD levels for all new products and redesigns of >3500 volts for LS. For device specific values reference the following specification: LS: 12MRM 93831A

http://onsemi.com
14

CHAPTER 3 Design Considerations Testing and Applications Assistance Form

http://onsemi.com
15

DESIGN CONSIDERATIONS
NOISE IMMUNITY

When mixing TTL families it is often desirable to know the guaranteed noise immunity for both LOW and HIGH logic levels. Table 2 lists the guaranteed logic levels for various TTL families and can be used to calculate noise margin. Table 3 specifies these noise margins for systems

containing LS, S, and/or ALS TTL. Note that Table 3 represents worst case limits and assumes a maximum power supply and temperature variation across the ICs which are interconnected, as well as maximum rated load. Increased noise immunity can be achieved by designing with decreased maximum allowable operating ranges.

Table 2. Worst Case TTL Logic Levels Electrical Characteristics

Military ( 55 to +125C) TTL Families TTL HTTL LPTTL STTL LSTTL ALS TTL Standard TTL 9000, 54/74 High Speed TTL 54/74H Low Power TTL 93L00 (MSI) Schottky TTL 54/74S, 93S00 Low Power Schottky TTL 54/74LS Advanced LS TTL, 54/74ALS VIL 0.8 0.8 0.7 0.8 0.7 0.8 VIH 2.0 2.0 2.0 2.0 2.0 2.0 VOL 0.4 0.4 0.3 0.5 0.4 0.4 VOH 2.4 2.4 2.4 2.5 2.5 2.5 Commercial (0 to 70C) VIL 0.8 0.8 0.8 0.8 0.8 0.8 0.8 VIH 2.0 2.0 2.0 2.0 2.0 2.0 2.0 VOL 0.4 0.4 0.3 0.5 0.5 0.5 0.5 VOH 2.4 2.4 2.4 2.7 2.7 2.75 2.5 Unit V V V V V V V

(5% VCC) (10% VCC)

VOL and VOH are the voltages generated at the output VIL and VIH are the voltage required at the input to generate the appropriate levels. The numbers given above are guaranteed worst-case values.

Table 3. (a) LOW Level Noise Margins (Commercial)

To From LS S ALS From VOL to VIL LS 300 300 300 S 300 300 300 ALS 300 300 300 Unit mV mV mV From

Table 3. (b) HIGH Level Noise Margins (Commercial)

To LS 700 700 750 500 S 700 700 750 500 ALS 700 700 750 500 Unit mV mV mV mV LS S ALS (5% VCC) ALS (10% VCC) From VOH to VIH

POWER CONSUMPTION

FANIN AND FANOUT

With the exception of ECL, all logic families exhibit increased power consumption at high frequencies. Care must be taken when switching multiple gates at high frequencies to assure that their combined dissipation does not exceed package and/or device capabilities. TTL devices are more efficient at high frequencies than CMOS.

In order to simplify designing with ON Semiconductor TTL devices, the input and output loading parameters of all families are normalized to the following values:
1 TTL Unit Load (U.L.) = 40 A in the HIGH state (Logic 1) 1 TTL Unit Load (U.L.) = 1.6 mA in the LOW state (Logic 0)

http://onsemi.com
16

Input loading and output drive factors of all products described in this handbook are related to these definitions.
EXAMPLES INPUT LOAD

1. A 7400 gate, which has a maximum IIL of 1.6 mA and IIH of 40 A is specified as having an input load factor of 1 U.L. (Also called a fan-in of 1 load.)

2. The 74LS95B which has a value of IIL = 0.8 mA and IIH of 40 A on the CP terminal, is specified as having an input LOW load factor of:
0.8 mA or 0.5 U.L. 1.6 mA and an input HIGH load factor of 40 A 40 A or 1 U.L.

3. The 74LS00 gate which has an IIL of 0.4 mA and an IIH of 20 A, has an input LOW load factor of:
0.4 mA or 0.25 U.L. an input HIGH load factor of 1.6 mA EXAMPLES OUTPUT DRIVE 20 A 40 A or 0.5 U.L.

1. The output of the 7400 will sink 16 mA in the LOW (logic 0) state and source 800 A in the HIGH (logic 1) state. The normalized output LOW drive factor is therefore:
16 mA = 10 U.L. 1.6 mA and the output HIGH drive factor is 800 A or 20 U.L. 40 A

2. The output of the 74LS00 will sink 8.0 mA in the LOW state and source 400 A in the HIGH state. The normalized output LOW drive factor is:
8.0 mA = 5 U.L. 1.6 mA and the output HIGH drive factor is 400 A or 10 U.L. 40 A

Relative load and drive factors for the basic TTL families are given in Table 4.
Table 4.
INPUT LOAD FAMILY HIGH 74LS00 7400 9000 74H00 74S00 74 ALS 0.5 U.L. 1 U.L. 1 U.L. 1.25 U.L. 1.25 U.L 0.5 U.L LOW 0.25 U.L. 1 U.L. 1 U.L. 1.25 U.L. 1.25 U.L. 0.0625 U.L HIGH 10 U.L. 20 U.L. 20 U.L. 25 U.L. 25 U.L. 10 U.L. LOW 5 U.L. 10 U.L. 10 U.L. 12.5 U.L. 12.5 U.L. 5 U.L. OUTPUT DRIVE

Values for MSI devices vary significantly from one element to another. Consult the appropriate data sheet for actual characteristics.

http://onsemi.com
17

WIREDOR APPLICATIONS

Certain TTL devices are provided with an open collector output to permit the Wired-OR (actually Wired-AND) function. This is achieved by connecting open collector outputs together and adding an external pull-up resistor.
MINIMUM AND MAXIMUM PULL-UP RESISTOR VALUES RX(MIN) VCC(MAX) VOL IOL N2(LOW) 1.6 mA where: Rx N1 N2 IOH = ICEX IOL VOL VOH VCC

The value of the pull-up resistor is determined by considering the fan-out of the OR tie and the number of devices in the OR tie. The pull-up resistor value is chosen from a range between maximum value (established to maintain the required VOH with all the OR tied outputs HIGH) and a minimum value (established so that the OR tie fan-out is not exceeded when only one output is LOW).

RX(MAX) =

VCC(MIN) VOH N1 IOH + N2(HIGH) 40 A

= External Pull-up Resistor = Number of Wired-OR Outputs = Number of Input Unit Loads (U.L.) being Driven = Output HIGH Leakage Current = LOW Level Fan-out Current of Driving Element = Output LOW Voltage Level (0.5 V) = Output HIGH Voltage Level (2.4 V) = Power Supply Voltage

Example: Four 74LS03 gate outputs driving four other LS gates or MSI inputs.
RX(MIN) = 5.25 V 0.5 V = 8.0 mA 1.6 mA 4.75 V = 742 6.4 mA 2.35 V = 4.9 k 0.48 mA

RX(MAX) =

4.75 V 2.4 V 4 100 A + 2 40 A = where: N1 N2 (HIGH) N2 (LOW) IOH IOL VOL VOH

=4 = 4 0.5 U.L. = 2 U.L. = 4 0.25 U.L. = 1 U.L. = 100 A = 8.0 mA = 0.5 V = 2.4 V

Any value of pull-up resistor between 742 and 4.9 k can be used. The lower values yield the fastest speeds while the higher values yield the lowest power dissipation.
UNUSED INPUTS

For best noise immunity and switching speed, unused TTL inputs should not be left floating, but should be held between 2.4 V and the absolute maximum input voltage. Two possible ways of handling unused inputs are: 1. Connect unused input to VCC, LS TTL inputs have a breakdown voltage >7.0 V and require, therefore no series resistor. 2. Connect the unused input to the output of an unused gate that is forced HIGH. CAUTION: Do not connect an unused LS input to another input of the same NAND or AND function. This method, recommended for normal TTL, increases the input coupling capacitance and thus reduces the ac noise immunity.
INPUT CAPACITANCE LINE DRIVING

As a rule of thumb, LS TTL inputs have an average capacitance of 5.0 pF for DIP packages. For an input that serves more than one internal function, each additional function adds approximately 1.5 pF.

Because of its superior capacitive drive characteristics, TTL logic is often used in line driving applications which require various termination techniques to maintain signal

http://onsemi.com
18

integrity. Parameters associated with this application are listed in Table 5. It is also often necessary to construct load lines to determine reflection waveforms in line driving applications. The input and output characteristics graphs of Section 2 (Figures 4, 7, and 8) can be very useful for this purpose.
OUTPUT RISE AND FALL TIMES

provide important information in determining reflection waveforms and crosstalk coefficients. Typical rise and fall times are approximately 6 ns for LS with a 50 pF load (measured 10 90%). Output rise and fall times become longer as capacitive load is increased.
INTERCONNECTION DELAYS

For those parts of a system in which timing is critical, designers should take into account the finite delay along the interconnections. These range from about 0.12 to 0.15 ns/inch for the type of interconnections normally used in TTL systems. Exceptions occur in systems using ground planes to reduce ground noise during a logic transition; ground planes give higher distributed capacitance and delays of about 0.15 to 0.22 ns/inch. Most interconnections on a logic board are short enough that the wiring and load capacitance can be treated as a lumped capacitance for purposes of estimating their effect

on the propagation delay of the driving circuit. When an interconnection is long enough that its delay is one-fourth to one-half of the signal transition time, the driver output waveform exhibits noticeable slope changes during a transition. This is evidence that during the initial portion of the output voltage transition the driver sees the characteristic impedance of the interconnection (normally 100 to 200 ), which for transient conditions appears as a resistor returned to the quiescent voltage existing just before the beginning of the transition. This characteristic impedance forms a voltage divider with the driver output impedance, tending to produce a signal transition having the same rise or fall time as in the no-load condition but with a reduced amplitude. This attenuated signal travels to the far end of the interconnection, which is essentially an unterminated transmission line, whereupon the signal starts doubling. Simultaneously, a reflection voltage is generated which has the same amplitude and polarity as the original signal, e.g., if the driver output signal is positive-going the reflection will be positive-going, and as it travels back toward the driver it adds to the line voltage. At the instant the reflection arrives at the driver it adds algebraically to the still-rising driver output, accelerating the transition rate and producing the noticeable change in slope.

Table 5. Output Characteristics for Schottky TTL Logic

(ALL MAXIMUM RATINGS) Characteristic Operating Voltage Range Output Drive: Standard Output Symbol VCC IOH IOL ISC IOH Buffer Output IOL ISC LS 74LSxxx 5 5% 0.4 8.0 20 to 100 15 24 40 to 225 Unit Vdc mA mA mA mA mA mA

http://onsemi.com
19

If an interconnection is of such length that its delay is longer than half the signal transition time, the attenuated output of the driver has time to reach substantial completion before the reflection arrives. In the limit, the waveform observed at the driver output is a 2-step signal with a pedestal. In this circumstance the first load circuit to receive a full signal is the one at the far end, because of the doubling effect, while the last one to receive a full signal is the one nearest the driver since it must wait for the reflection to complete the transition. Thus, in a worst-case situation, the net contribution to the overall delay is twice the delay of the interconnection because the initial part of the signal must travel to the far end of the line and the reflection must return. When load circuits are distributed along an interconnection, the input capacitance of each will cause a small reflection having a polarity opposite that of the signal

transition, and each capacitance also slows the transition rate of the signal as it passes by. The series of small reflections, arriving back at the driver, is subtractive and has the effect of reducing the apparent amplitude of the signal. The successive slowing of the transition rate of the transmitted signal means that it takes longer for the signal to rise or fall to the threshold level of any particular load circuit. A rough but workable approach is to treat the load capacitances as an increase in the intrinsic distributed capacitance of the interconnection. Increasing the distributed capacitance of a transmission line reduces its impedance and increases its delay. A good approximation for ordinary TTL interconnections is that distributed load capacitance decreases the characteristic impedance by about one-third and increases the delay by one-half.

ABSOLUTE MAXIMUM RATINGS (above which the useful life may be impaired)

Functional operation under these conditions is not implied.

CHARACTERISTIC Storage Temperature Temperature (Ambient) Under Bias VCC Pin Potential to Ground Pin *Input Voltage (dc) Diode Inputs *Input Current (dc) Voltage Applied to Open Collector Outputs (Output HIGH) High Level Voltage Applied to Disabled 3-State Output Current Applied to Output in Low State (Max) LS 65C to + 150C 55C to + 125C 0.5 V to + 7.0 V 0.5 V to +15 V 30 mA to + 5.0 mA 0.5 V to + 10 V 5.5 V Twice Rated IOL

*Either input voltage limit or input current limit is sufficient to protect the inputs Circuits with 5.5 V maximum limits are listed below.

Device types having inputs limited to 5.5 V are as follows:

SN74LS245 SN74LS640/641/642/645 SN74LS299 SN74LS151/251 Inputs connected to outputs. Inputs connected to outputs. Certain Inputs. Multiplexer Inputs.

http://onsemi.com
20

DEFINITION OF SYMBOLS AND TERMS USED IN THIS DATA BOOK

CURRENTS Positive current is defined as conventional current flow into a device. Negative current is defined as conventional current flow out of a device. All current limits are specified as absolute values. ICC IIH IIL IOH Supply Current The current flowing into the VCC supply terminal of a circuit with the specified input conditions and the outputs open. When not specified, input conditions are chosen to guarantee worst case operation. Input HIGH current The current flowing into an input when a specified HIGH voltage is applied to that input. Input LOW current The current flowing out of an input when a specified LOW voltage is applied to that input. Output HIGH current. The leakage current flowing into a turned off open collector output with a specified HIGH output voltage applied. For devices with a pull-up circuit, the IOH is the current flowing out of an output which is in the HIGH state. Output LOW current The current flowing into an output which is in the LOW state. Output short-circuit current The current flowing out of an output which is in the HIGH state when that output is short circuit to ground (or other specified potential). Output off current HIGH The current flowing into a disabled 3-state output with a specified HIGH output voltage applied. Output off current LOW The current flowing out of a disabled 3-state output with a specified LOW output voltage applied.

IOL IOS IOZH IOZL

VOLTAGES All voltages are referenced to ground. Negative voltage limits are specified as absolute values (i.e., 10 V is greater than 1.0 V). VCC VIK(MAX) Supply voltage The range of power supply voltage over which the device is guaranteed to operate within the specified limits. Input clamp diode voltage The most negative voltage at an input when the specified current is forced out of that input terminal. This parameter guarantees the integrity of the input diode which is intended to clamp negative ringing at the input terminal. Input HIGH voltage The range of input voltages recognized by the device as a logic HIGH. Minimum input HIGH voltage The minimum allowed input HIGH in a logic system. This value represents the guaranteed input HIGH threshold for the device. Input LOW voltage The range of input voltages recognized by the device as a logic LOW. Maximum input LOW voltage The maximum allowed input LOW in a system. This value represents the guaranteed input LOW threshold for the device. Output HIGH voltage The minimum guaranteed voltage at an output terminal for the specified output current IOH and at the minimum value of VCC. Output LOW voltage The maximum guaranteed voltage at an output terminal sinking the maximum specified load current IOL. Positive-going threshold voltage The input voltage of a variable threshold device (ie., Schmitt Trigger) that is interpreted as a VIH as the input transition rises from below VT(MIN). Negative-going threshold voltage The input voltage of a variable threshold device (ie., Schmitt Trigger) that is interpreted as a VIL as the input transition falls from above VT+(MAX).

VIH VIH(MIN) VIL VIL(MAX) VOH(MIN) VOL(MAX) VT+ VT

http://onsemi.com
21

AC SWITCHING PARAMETERS AND WAVEFORMS tPLH LOW-TO-HIGH propagation delay time : The time delay between specified reference points, typically 1.3 V for LS, on the input and output voltage waveforms, with the output changing from the defined LOW level to the defined HIGH level. HIGH-TO-LOW propagation delay time: The time delay between specified reference points, typically 1.3 V for LS, on the input and output voltage waveforms, with the output changing from the defined HIGH level to the defined LOW level. For Inverting Function For Non-Inverting

tPHL

VIN Vout

tPHL tPLH

VIN

tPLH

tPHL

Vout

tr tf

Waveform Rise Time: LOW to HIGH logic transition time, measured from the 10% to 90% points of the waveform. Waveform Fall Time: HIGH to LOW logic transition time, measured the 90% to the 10% points of the waveform.
tr 90% 90% tf

10%

10%

tPHZ

Output disable time: HIGH to Z The time delay between the specified reference points on the input and output voltage waveforms, with the 3-state output changing from the defined HIGH level to a high impedance (OFF) state. Reference point on the output voltage waveform is VOH 0.5 V for LS and VOH 0.3 V for FAST. Output enable time: Z to HIGH The time delay between the specified reference points on the input and output voltage waveforms, with the 3-state output changing from a high impedance (OFF) state to a HIGH level.
Enable

tPZH

Enable tPZH

tPHZ VOH 3.5 V .5 for LS

Vout

http://onsemi.com
22

tPLZ

Output disable time: LOW to Z The time delay between the specified reference points on the input and output voltage waveforms, with the 3-state output changing from the defined LOW level to a high impedance (OFF) state. Reference point on the output voltage waveform is VOL + 0.5 V for LS. Output enable time: Z to LOW The time delay between the specified reference points on the input and output voltage waveforms with the 3-state output changing from a high impedance (OFF) state to a HIGH level.
Enable

tPZL

Enable Vout tPZL

tPLZ

VOZ = 1.5 V .5 for LS

trec

Recovery time Time required between an asynchronous signal (SET, RESET, CLEAR or PARALLEL load) and the active edge of a synchronous control signal, to insure that the device will properly respond to the synchronous signal.

Asynch

Asynch trec

Control

th

Hold Time The interval of time from the active edge of the control signal (usually the clock) to when the data to be recognized is no longer required to ensure proper interpretation of the data. A negative hold time indicates that the data may be removed at some time prior to the active edge of the control signal. Setup time The interval of time during which the data to be recognized is required to remain constant prior to the active edge of the control signal to ensure proper data recognition. A negative setup time indicates that data may be initiated sometime after the active transition of the timing pulse and still be recognized.

ts

VIN ts(L) CP th(L)

VIN ts(H) CP th(H)

http://onsemi.com
23

tw or tpw

Pulse width The time between the specified amplitude points (1.3 V for LS) on the leading and trailing edges of a pulse.
twL

twH

fMAX

Toggle frequency/operating frequency The maximum rate at which clock pulses meeting the clock requirements (ie., tWH, tWL, and tr, tf) may be applied to a sequential circuit. Above this frequency the device may cease to function. Guaranteed maximum clock frequency The lowest possible value for fMAX.

fMAXmin

TESTING DC TEST CIRCUITS

The following test circuits and forcing functions represent ON Semiconductors typical DC test procedures.
VOH AND VOL TESTS Force IOHMAX or IOLMAX Measure VOH or VOL IIHH, IIH AND IIL TESTS Force 7, 5.5, 2.7, or 0.4 V Measure IIHH, IIH, or IIL VIHMIN or VILMAX VIHMIN or VILMAX DUT Io DUT + Vo Vi IOS TEST Measure IOS DUT

VIK TEST Force Ii Measure VIK + Vik DUT Ii = 18 mA

IOH, IOZH, and IOZL TESTS Force 5.5, 2.4, or 0.4 V Measure IO DUT Io

ICC TEST Measure ICC VCC MAX

Vo

GND or 4.5 V*

DUT

Outputs Open

*Unless otherwise indicated, input conditions are selected to produce a worst case condition.

http://onsemi.com
24

AC TEST CIRCUITS

The following test circuits and conditions represent ON Semiconductors typical test procedures. AC waveforms and terminology can be found on pages 22 to 24.
FUNCTIONAL TESTING OF TTL IN A NOISY ENVIRONMENT/DYNAMIC THRESHOLD

Testing noise (noise generated by the test system itself and noise generated by TTL devices under test interacting with the test system) adds to, or subtracts from the threshold voltage applied to the TTL device under test. For this reason ON Semiconductor does not recommend functional testing of TTL devices using threshold levels of 0.8 V and 2.0 V.
VOUT Trigger Threshold

Instead, good TTL testing techniques call for hard levels of less than 0.5 V VIL and greater than 2.4 V VIH to be applied for functional testing. Input threshold voltages should be tested separately, and only (for noise reasons above) after setting the device state with a hard level.

VOH

VOL

VIN

Dynamic Threshold Region of output instability; Dynamic Noise contribution to apparent input threshold

The VIN versus VOUT plot shows the practical effect of testing noise on a logic IC device. The actual device Trigger threshold is represented by the initial low to high output transition. The device will oscillate if the input voltage does not exceed the trigger threshold plus the noise generated by the interaction of the test system or given application with the device. The Dynamic threshold (that creates Quiescent outputs), is the input logic level required to overcome the interactive DYNAMIC NOISE generated by a device switching states.

The amount of interactive DYNAMIC NOISE can be characterized by the difference between the Trigger threshold and the Dynamic threshold of the device under test. A simple number cannot be assigned to this parameter as it is heavily dependent on any given application or test environment. So although the Trigger threshold of any given device will correlate well between any test system, the correlation of Dynamic threshold cannot be made directly and will have meaning only in a relative sense.

http://onsemi.com
25

LS TEST CIRCUITS Test Circuit for Standard Output Devices

VCC

PULSE GENERATOR SETTINGS (UNLESS OTHERWISE SPECIFIED)

LS Frequency = 1 MHz Duty Cycle = 50% 1 TLH (tr) = 6 ns (15)* 1 THL (tf) = 6 ns (15)* Amplitude = 0 to 3 V

VIN PULSE GEN 51

DUT 15 pF*

VOUT

* The specified propagation delay limits can be guaranteed with a 15 ns input rise time on all parameters except those requiring narrow pulse widths. Any frequency measurement over 15 MHz or pulse width less than 30 ns must be performed with a 6 ns input rise time.

Test Circuit for Open Collector Output Devices

VCC VCC

RL VIN PULSE GEN 51 15 pF*

DUT

VOUT

*includes all probe and jig capacitance

Optional LS Load (GuaranteedNot Tested)

VCC

RL

CL

http://onsemi.com
26

APPLICATIONS ASSISTANCE FORM

In the event that you have any questions or concerns about the performance of any ON Semiconductor device listed in this catalog, please contact your local ON Semiconductor sales office or the ON Semiconductor Help line for assistance. If further information is required, you can request direct factory assistance. Please fill out as much of the form as is possible if you are contacting ON Semiconductor for assistance or are sending devices back to ON Semiconductor for analysis. Your information can greatly improve the accuracy of analysis and can dramatically improve the correlation response and resolution time. Items 4 thru 8 of the following form contains important questions that can be invaluable in analyzing application or device problems. It can be used as a self-help diagnostic guideline or for a baseline of information gathering to begin a dialog with ON Semiconductor representatives. ON Semiconductor Device Correlation/Component Analysis Request Form Please fill out entire form and return with devices to ON Semiconductor, R&QA Dept., 5005 E. McDowell, Phoenix, AZ 85008. 1) Name of Person Requesting Correlation: Phone No: 2) Alternate Contact: 3) Device Type (user part number): 4) Industry Generic Device Type: 5) # of devices tested/sampled: # of devices in question*: # returned for correlation: * In the event of 100% failure, does Customer have other date codes of ON Semiconductor devices that pass inspection? Yes No Please specify passing date code(s) if applicable If none, does customer have viable alternate vendor(s) for device type? Yes No Alternate vendors name 6) Date code(s) and Serial Number(s) of devices returned for correlation If possible, please provide one or two good units (ON Semiconductors and/or other vendor) for comparison: 7) Describe USER process that device(s) are questionable in: Incoming component inspection {test system = ?}: Design prototyping: Board test/burn-in: Other (please describe): 8) Please describe the device correlation operating parameters as completely as possible for device(s) in question: > Describe all pin conditions (e.g. floating, high, low, under test, stimulated but not under test, whatever ...), including any input or output loading conditions (resistors, caps, clamps, driving devices or devices being driven ...). Potentially critical information includes: Input waveform timing relationships Input edge rates Input Overshoot or Undershoot Magnitude and Duration Output Overshoot or Undershoot Magnitude and Duration > Photographs, plots or sketches of relevent inputs and outputs with voltages and time divisions clearly identified for all waveforms are greatly desirable. > VCC and Ground waveforms should be carefully described as these characteristics vary greatly between applications and test systems. Dynamic characteristics of Ground and VCC during device switching can dramatically effect input and internal operating levels. Ground & VCC measurements should be made as physically close to the device in question as possible. > Are there specific circumstances that seem to make the questionable unit(s) worse? Better? Temperature VCC Input rise/fall time Output loading (current/capacitance) Others > ATE functional data should include pattern with decoding key and critical parameters such as VCC, input voltages, Func step rate, voltage expected, time to measure. http://onsemi.com
27

Job Title: Phone/Position:

Company:

http://onsemi.com
28

CHAPTER 4 LS Data Sheets

http://onsemi.com
29

SN74LS00 Quad 2-Input NAND Gate

ESD > 3500 Volts
VCC 14 13 12 11 10 9 8

http://onsemi.com

LOW POWER SCHOTTKY

1 2 3 4 5 6 7 GND

GUARANTEED OPERATING RANGES

Symbol VCC TA IOH IOL Parameter Supply Voltage Operating Ambient Temperature Range Output Current High Output Current Low Min 4.75 0 Typ 5.0 25 Max 5.25 70 0.4 8.0 Unit V C mA mA
14 1

PLASTIC N SUFFIX CASE 646

14 1

SOIC D SUFFIX CASE 751A

ORDERING INFORMATION
Device SN74LS00N SN74LS00D Package 14 Pin DIP 14 Pin Shipping 2000 Units/Box 2500/Tape & Reel

Semiconductor Components Industries, LLC, 1999

30

December, 1999 Rev. 6

Publication Order Number: SN74LS00/D

SN74LS00
DC CHARACTERISTICS OVER OPERATING TEMPERATURE RANGE (unless otherwise specified)
Limits Symbol VIH VIL VIK VOH Parameter Input HIGH Voltage Input LOW Voltage Input Clamp Diode Voltage Output HIGH Voltage 2.7 0.65 3.5 0.25 VOL Out ut Output LOW Voltage 0.35 IIH IIL IOS In ut Input HIGH Current 0.1 Input LOW Current Short Circuit Current (Note 1) Power Supply Current ICC Total, Output HIGH Total, Output LOW 1.6 4.4 mA VCC = MAX 20 0.4 100 0.5 20 V A mA mA mA IOL = 8.0 mA 0.4 Min 2.0 0.8 1.5 Typ Max Unit V V V V V Test Conditions Guaranteed Input HIGH Voltage for All Inputs Guaranteed Input LOW Voltage for All Inputs VCC = MIN, IIN = 18 mA VCC = MIN, IOH = MAX, VIN = VIH or VIL per Truth Table IOL = 4.0 mA VCC = VCC MIN, VIN = VIL or VIH per Truth Table

VCC = MAX, VIN = 2.7 V VCC = MAX, VIN = 7.0 V VCC = MAX, VIN = 0.4 V VCC = MAX

Note 1: Not more than one output should be shorted at a time, nor for more than 1 second.

AC CHARACTERISTICS (TA = 25C)

Limits Symbol tPLH tPHL Parameter TurnOff Delay, Input to Output TurnOn Delay, Input to Output Min Typ 9.0 10 Max 15 15 Unit ns ns Test Conditions VCC = 5.0 V CL = 15 pF

http://onsemi.com
31

SN74LS04 Hex Inverter

VCC 14 13 12 11 10 9 8

http://onsemi.com

7 GND

LOW POWER SCHOTTKY

GUARANTEED OPERATING RANGES

Symbol VCC TA IOH IOL Parameter Supply Voltage Operating Ambient Temperature Range Output Current High Output Current Low Min 4.75 0 Typ 5.0 25 Max 5.25 70 0.4 8.0 Unit V C mA mA
14 1

PLASTIC N SUFFIX CASE 646

14 1

SOIC D SUFFIX CASE 751A

ORDERING INFORMATION
Device SN74LS04N SN74LS04D Package 14 Pin DIP 14 Pin Shipping 2000 Units/Box 2500/Tape & Reel

Semiconductor Components Industries, LLC, 1999

32

December, 1999 Rev. 6

Publication Order Number: SN74LS04/D

SN74LS04
DC CHARACTERISTICS OVER OPERATING TEMPERATURE RANGE (unless otherwise specified)
Limits Symbol VIH VIL VIK VOH Parameter Input HIGH Voltage Input LOW Voltage Input Clamp Diode Voltage Output HIGH Voltage 2.7 0.65 3.5 0.25 VOL Out ut Output LOW Voltage 0.35 IIH IIL IOS In ut Input HIGH Current 0.1 Input LOW Current Short Circuit Current (Note 1) Power Supply Current ICC Total, Output HIGH Total, Output LOW 2.4 6.6 mA VCC = MAX 20 0.4 100 0.5 20 V A mA mA mA IOL = 8.0 mA 0.4 Min 2.0 0.8 1.5 Typ Max Unit V V V V V Test Conditions Guaranteed Input HIGH Voltage for All Inputs Guaranteed Input LOW Voltage for All Inputs VCC = MIN, IIN = 18 mA VCC = MIN, IOH = MAX, VIN = VIH or VIL per Truth Table IOL = 4.0 mA VCC = VCC MIN, VIN = VIL or VIH per Truth Table

VCC = MAX, VIN = 2.7 V VCC = MAX, VIN = 7.0 V VCC = MAX, VIN = 0.4 V VCC = MAX

Note 1: Not more than one output should be shorted at a time, nor for more than 1 second.

AC CHARACTERISTICS (TA = 25C)

Limits Symbol tPLH tPHL Parameter TurnOff Delay, Input to Output TurnOn Delay, Input to Output Min Typ 9.0 10 Max 15 15 Unit ns ns Test Conditions VCC = 5.0 V CL = 15 pF

http://onsemi.com
33

SN74LS05 Hex Inverter

VCC 14 13 12 * 11 10 * 9 * 8

http://onsemi.com

* 1 2 3

* 4 5

* 6 7 GND

LOW POWER SCHOTTKY

* OPEN COLLECTOR OUTPUTS

GUARANTEED OPERATING RANGES

Symbol VCC TA VOH IOL Parameter Supply Voltage Operating Ambient Temperature Range Output Voltage High Output Current Low Min 4.75 0 Typ 5.0 25 Max 5.25 70 5.5 8.0 Unit V C V mA
1 14

PLASTIC N SUFFIX CASE 646

14 1

SOIC D SUFFIX CASE 751A

ORDERING INFORMATION
Device SN74LS05N SN74LS05D Package 14 Pin DIP 14 Pin Shipping 2000 Units/Box 2500/Tape & Reel

Semiconductor Components Industries, LLC, 1999

34

December, 1999 Rev. 6

Publication Order Number: SN74LS05/D

SN74LS05
DC CHARACTERISTICS OVER OPERATING TEMPERATURE RANGE (unless otherwise specified)
Limits Symbol VIH VIL VIK IOH VOL Parameter Input HIGH Voltage Input LOW Voltage Input Clamp Diode Voltage Output HIGH Current 0.25 Out ut Output LOW Voltage 0.35 IIH IIL In ut Input HIGH Current 0.1 Input LOW Current Power Supply Current ICC Total, Output HIGH Total, Output LOW 2.4 6.6 mA VCC = MAX 0.4 0.5 20 V A mA mA IOL = 8.0 mA 0.65 Min 2.0 0.8 1.5 100 0.4 Typ Max Unit V V V Test Conditions Guaranteed Input HIGH Voltage for All Inputs Guaranteed Input LOW Voltage for All Inputs VCC = MIN, IIN = 18 mA VCC = MIN, VOH = MAX IOL = 4.0 mA VCC = VCC MIN, VIN = VIL or VIH per Truth Table

mA
V

VCC = MAX, VIN = 2.7 V VCC = MAX, VIN = 7.0 V VCC = MAX, VIN = 0.4 V

AC CHARACTERISTICS (TA = 25C)

Limits Symbol tPLH tPHL Parameter TurnOff Delay, Input to Output TurnOn Delay, Input to Output Min Typ 17 15 Max 32 28 Unit ns ns Test Conditions VCC = 5.0 V CL = 15 pF, RL = 2.0 k

http://onsemi.com
35

SN74LS08 Quad 2-Input AND Gate

VCC 14 13 12 11 10 9 8

http://onsemi.com

7 GND

LOW POWER SCHOTTKY

GUARANTEED OPERATING RANGES

Symbol VCC TA IOH IOL Parameter Supply Voltage Operating Ambient Temperature Range Output Current High Output Current Low Min 4.75 0 Typ 5.0 25 Max 5.25 70 0.4 8.0 Unit V C mA mA
14 1

PLASTIC N SUFFIX CASE 646

14 1

SOIC D SUFFIX CASE 751A

ORDERING INFORMATION
Device SN74LS08N SN74LS08D Package 14 Pin DIP 14 Pin Shipping 2000 Units/Box 2500/Tape & Reel

Semiconductor Components Industries, LLC, 1999

36

December, 1999 Rev. 6

Publication Order Number: SN74LS08/D

SN74LS08
DC CHARACTERISTICS OVER OPERATING TEMPERATURE RANGE (unless otherwise specified)
Limits Symbol VIH VIL VIK VOH Parameter Input HIGH Voltage Input LOW Voltage Input Clamp Diode Voltage Output HIGH Voltage 2.7 0.65 3.5 0.25 VOL Out ut Output LOW Voltage 0.35 IIH IIL IOS In ut Input HIGH Current 0.1 Input LOW Current Short Circuit Current (Note 1) Power Supply Current ICC Total, Output HIGH Total, Output LOW 4.8 8.8 mA VCC = MAX 20 0.4 100 0.5 20 V A mA mA mA IOL = 8.0 mA 0.4 Min 2.0 0.8 1.5 Typ Max Unit V V V V V Test Conditions Guaranteed Input HIGH Voltage for All Inputs Guaranteed Input LOW Voltage for All Inputs VCC = MIN, IIN = 18 mA VCC = MIN, IOH = MAX, VIN = VIH or VIL per Truth Table IOL = 4.0 mA VCC = VCC MIN, VIN = VIL or VIH per Truth Table

VCC = MAX, VIN = 2.7 V VCC = MAX, VIN = 7.0 V VCC = MAX, VIN = 0.4 V VCC = MAX

Note 1: Not more than one output should be shorted at a time, nor for more than 1 second.

AC CHARACTERISTICS (TA = 25C)

Limits Symbol tPLH tPHL Parameter TurnOff Delay, Input to Output TurnOn Delay, Input to Output Min Typ 8.0 10 Max 15 20 Unit ns ns Test Conditions VCC = 5.0 V CL = 15 pF

http://onsemi.com
37

SN74LS14

Schmitt Triggers Dual Gate/Hex Inverter

The SN74LS14 contains logic gates / inverters which accept standard TTL input signals and provide standard TTL output levels. They are capable of transforming slowly changing input signals into sharply defined, jitter-free output signals. Additionally, they have greater noise margin than conventional inverters. Each circuit contains a Schmitt trigger followed by a Darlington level shifter and a phase splitter driving a TTL totem pole output. The Schmitt trigger uses positive feedback to effectively speed-up slow input transitions, and provide different input threshold voltages for positive and negative-going transitions. This hysteresis between the positive-going and negative-going input thresholds (typically 800 mV) is determined internally by resistor ratios and is essentially insensitive to temperature and supply voltage variations.

http://onsemi.com

LOW POWER SCHOTTKY

LOGIC AND CONNECTION DIAGRAMS

VCC 14 13 SN74LS14 12 11 10 9 8

14 1

PLASTIC N SUFFIX CASE 646

7 GND

14 1

GUARANTEED OPERATING RANGES

Symbol VCC TA IOH IOL Parameter Supply Voltage Operating Ambient Temperature Range Output Current High Output Current Low Min 4.75 0 Typ 5.0 25 Max 5.25 70 0.4 8.0 Unit V C

SOIC D SUFFIX CASE 751A

ORDERING INFORMATION
mA mA Device SN74LS14N SN74LS14D Package 14 Pin DIP 14 Pin Shipping 2000 Units/Box 2500/Tape & Reel

Semiconductor Components Industries, LLC, 1999

38

December, 1999 Rev. 0

Publication Order Number: SN74LS14/D

SN74LS14
DC CHARACTERISTICS OVER OPERATING TEMPERATURE RANGE (unless otherwise specified)
Limits Symbol VT+ VT VT+ VT VIK VOH VO OL IT+ IT IIH IIL IOS Parameter Positive-Going Threshold Voltage Negative-Going Threshold Voltage Hysteresis Input Clamp Diode Voltage Output HIGH Voltage Output LOW Voltage 0.35 Input Current at Positive-Going Threshold Input Current at Negative-Going Threshold Input HIGH Current 0.1 Input LOW Current Short Circuit Current (Note 1) Power Supply Current ICC Total, Output HIGH , 12 Total, Output LOW Note 1: Not more than one output should be shorted at a time, nor for more than 1 second. 21 20 8.6 0.4 100 16 mA VCC = MAX 0.14 0.18 1.0 20 0.5 V mA mA A mA mA mA 2.7 Min 1.5 0.6 0.4 0.8 0.65 3.4 0.25 0.4 1.5 Typ Max 2.0 1.1 Unit V V V V V V Test Conditions VCC = 5.0 V VCC = 5.0 V VCC = 5.0 V VCC = MIN, IIN = 18 mA VCC = MIN, IOH = 400 A, VIN = VIL VCC = MIN, IOL = 4.0 mA, VIN = 2.0 V VCC = MIN, IOL = 8.0 mA, VIN = 2.0 V VCC = 5.0 V, VIN = VT+ VCC = 5.0 V, VIN = VT VCC = MAX, VIN = 2.7 V VCC = MAX, VIN = 7.0 V VCC = MAX, VIN = 0.4 V VCC = MAX, VOUT = 0 V

AC CHARACTERISTICS (TA = 25C)

Symbol tPLH tPHL Parameter Propagation Delay, Input to Output Propagation Delay, Input to Output Max 22 22 Unit ns ns Test Conditions VCC = 5.0 V CL = 15 pF

3V VIN 0V tPHL tPLH 1.6 V 0.8 V

VOUT

1.3 V

1.3 V

Figure 1. AC Waveforms

http://onsemi.com
39

SN74LS14
5 V O , OUTPUT VOLTAGE (VOLTS) 4 2 V T , THRESHOLD VOLTAGE (VOLTS) V T, HYSTERESIS (VOLTS)

VCC = 5 V TA = 25C

TA = 25C VT+

1.6

1.2 VT 0.8

DVT

0.4

0.4

0.95 1.2 VIN, INPUT VOLTAGE (VOLTS)

1.8

0 4.5

4.75 5 5.25 VCC, POWER SUPPLY VOLTAGE (VOLTS)

5.5

Figure 2. VIN versus VOUT Transfer Function

1.9 V T , THRESHOLD VOLTAGE (VOLTS) V T, HYSTERESIS (VOLTS) 1.7 1.5 1.3 1.1 0.9 0.7 55 VT VT+

Figure 3. Threshold Voltage and Hysteresis versus Power Supply Voltage

VT 0 25 75 TA, AMBIENT TEMPERATURE (C)

125

Figure 4. Threshold Voltage Hysteresis versus Temperature

http://onsemi.com
40

SN74LS32 Quad 2-Input OR Gate

VCC 14 13 12 11 10 9 8

http://onsemi.com

7 GND

LOW POWER SCHOTTKY

GUARANTEED OPERATING RANGES

Symbol VCC TA IOH IOL Parameter Supply Voltage Operating Ambient Temperature Range Output Current High Output Current Low Min 4.75 0 Typ 5.0 25 Max 5.25 70 0.4 8.0 Unit V C mA mA
14 1

PLASTIC N SUFFIX CASE 646

14 1

SOIC D SUFFIX CASE 751A

ORDERING INFORMATION
Device SN74LS32N SN74LS32D Package 14 Pin DIP 14 Pin Shipping 2000 Units/Box 2500/Tape & Reel

Semiconductor Components Industries, LLC, 1999

41

December, 1999 Rev. 6

Publication Order Number: SN74LS32/D

SN74LS32
DC CHARACTERISTICS OVER OPERATING TEMPERATURE RANGE (unless otherwise specified)
Limits Symbol VIH VIL VIK VOH Parameter Input HIGH Voltage Input LOW Voltage Input Clamp Diode Voltage Output HIGH Voltage 2.7 0.65 3.5 0.25 VO OL Output LOW Voltage 0.35 IIH IIL IOS ICC Input HIGH Current 0.1 Input LOW Current Short Circuit Current (Note 1) Power Supply Current Total, Output HIGH Total, Output LOW 20 0.4 100 6.2 9.8 0.5 20 V A mA mA mA IOL = 8.0 mA 0.4 Min 2.0 0.8 1.5 Typ Max Unit V V V V V Test Conditions Guaranteed Input HIGH Voltage for All Inputs Guaranteed Input LOW Voltage for All Inputs VCC = MIN, IIN = 18 mA VCC = MIN, IOH = MAX, VIN = VIH or VIL per Truth Table IOL = 4.0 mA VCC = VCC MIN, VIN = VIL or VIH per Truth Table

VCC = MAX, VIN = 2.7 V VCC = MAX, VIN = 7.0 V VCC = MAX, VIN = 0.4 V VCC = MAX VCC = MAX

mA

Note 1: Not more than one output should be shorted at a time, nor for more than 1 second.

AC CHARACTERISTICS (TA = 25C)

Limits Symbol tPLH tPHL Parameter Turn-Off Delay, Input to Output Turn-On Delay, Input to Output Min Typ 14 14 Max 22 22 Unit ns ns Test Conditions VCC = 5.0 V CL = 15 pF

http://onsemi.com
42

SN74LS38 Quad 2-Input NAND Buffer

VCC 14 13 12 * 11 10 9 * 8

http://onsemi.com

* 1 2 3 4 5 6

* 7 GND

LOW POWER SCHOTTKY

* OPEN COLLECTOR OUTPUTS

GUARANTEED OPERATING RANGES

Symbol VCC TA VOH IOL Parameter Supply Voltage Operating Ambient Temperature Range Output Voltage High Output Current Low Min 4.75 0 Typ 5.0 25 Max 5.25 70 5.5 24 Unit V C V mA
14 1

PLASTIC N SUFFIX CASE 646

14 1

SOIC D SUFFIX CASE 751A

ORDERING INFORMATION
Device SN74LS38N SN74LS38D Package 14 Pin DIP 14 Pin Shipping 2000 Units/Box 2500/Tape & Reel

Semiconductor Components Industries, LLC, 1999

43

December, 1999 Rev. 6

Publication Order Number: SN74LS38/D

SN74LS38
DC CHARACTERISTICS OVER OPERATING TEMPERATURE RANGE (unless otherwise specified)
Limits Symbol VIH VIL VIK IOH VO OL Parameter Input HIGH Voltage Input LOW Voltage Input Clamp Diode Voltage Output HIGH Current 0.25 Output LOW Voltage 0.35 IIH IIL ICC Input HIGH Current 0.1 Input LOW Current Power Supply Current Total, Output HIGH Total, Output LOW 0.4 2.0 12 0.5 20 V A mA mA IOL = 24 mA 0.65 Min 2.0 0.8 1.5 250 0.4 Typ Max Unit V V V A V Test Conditions Guaranteed Input HIGH Voltage for All Inputs Guaranteed Input LOW Voltage for All Inputs VCC = MIN, IIN = 18 mA VCC = MIN, VOH = MAX IOL = 12 mA VCC = VCC MIN, VIN = VIL or VIH per Truth Table

VCC = MAX, VIN = 2.4 V VCC = MAX, VIN = 7.0 V VCC = MAX, VIN = 0.4 V VCC = MAX

mA

AC CHARACTERISTICS (TA = 25C)

Limits Symbol tPLH tPHL Parameter Turn-Off Delay, Input to Output Turn-On Delay, Input to Output Min Typ 20 18 Max 32 28 Unit ns ns Test Conditions VCC = 5.0 V, RL = 667 CL = 45 pF

http://onsemi.com
44

SN74LS42 One-of-Ten Decoder

The LSTTL / MSI SN74LS42 is a Multipurpose Decoder designed to accept four BCD inputs and provide ten mutually exclusive outputs. The LS42 is fabricated with the Schottky barrier diode process for high speed and is completely compatible with all ON Semiconductor TTL families. Multifunction Capability Mutually Exclusive Outputs Demultiplexing Capability Input Clamp Diodes Limit High Speed Termination Effects

http://onsemi.com

LOW POWER SCHOTTKY

GUARANTEED OPERATING RANGES

Symbol VCC TA IOH IOL Parameter Supply Voltage Operating Ambient Temperature Range Output Current High Output Current Low Min 4.75 0 Typ 5.0 25 Max 5.25 70 0.4 8.0 Unit V C mA mA
16 1

PLASTIC N SUFFIX CASE 648

16 1

SOIC D SUFFIX CASE 751B

ORDERING INFORMATION
Device SN74LS42N SN74LS42D Package 16 Pin DIP 16 Pin Shipping 2000 Units/Box 2500/Tape & Reel

Semiconductor Components Industries, LLC, 1999

45

December, 1999 Rev. 6

Publication Order Number: SN74LS42/D

SN74LS42
CONNECTION DIAGRAM DIP (TOP VIEW)
VCC 16 A0 15 A1 14 A2 13 A3 12 9 11 8 10 7 9 NOTE: The Flatpak version has the same pinouts (Connection Diagram) as the Dual In-Line Package. 1 0 2 1 3 2 4 3 5 4 6 5 7 6 8 GND

LOADING (Note a) PIN NAMES A0 A3 0 to 9 Address Inputs Outputs, Active LOW HIGH 0.5 U.L. 10 U.L. LOW 0.25 U.L. 5 U.L.

NOTES: a) 1 TTL Unit Load (U.L.) = 40 mA HIGH/1.6 mA LOW.

LOGIC SYMBOL
15 14 13 12

A0

A1

A2

A3

0 1 2 3 4 5 6 7 8 9

1 2 3 4 5 6 7 9 10 11 VCC = PIN 16 GND = PIN 8

LOGIC DIAGRAM
A0
15

A1
14

A2
13

A3
12

10

11

VCC = PIN 16 GND = PIN 8 = PIN NUMBERS

http://onsemi.com
46

SN74LS42
FUNCTIONAL DESCRIPTION The LS42 decoder accepts four active HIGH BCD inputs and provides ten mutually exclusive active LOW outputs, as shown by logic symbol or diagram. The active LOW outputs facilitate addressing other MSI units with LOW input enables. The logic design of the LS42 ensures that all outputs are HIGH when binary codes greater than nine are applied to the inputs. The most significant input A3 produces a useful inhibit function when the LS42 is used as a one-of-eight decoder. The A3 input can also be used as the Data input in an 8-output demultiplexer application.

TRUTH TABLE
A0 L H L H L H L H L H L H L H L H A1 L L H H L L H H L L H H L L H H A2 L L L L H H H H L L L L H H H H A3 L L L L L L L L H H H H H H H H 0 L H H H H H H H H H H H H H H H 1 H L H H H H H H H H H H H H H H 2 H H L H H H H H H H H H H H H H 3 H H H L H H H H H H H H H H H H 4 H H H H L H H H H H H H H H H H 5 H H H H H L H H H H H H H H H H 6 H H H H H H L H H H H H H H H H 7 H H H H H H H L H H H H H H H H 8 H H H H H H H H L H H H H H H H 9 H H H H H H H H H L H H H H H H

H = HIGH Voltage Level L = LOW Voltage Level

http://onsemi.com
47

SN74LS42
DC CHARACTERISTICS OVER OPERATING TEMPERATURE RANGE (unless otherwise specified)
Limits Symbol VIH VIL VIK VOH Parameter Input HIGH Voltage Input LOW Voltage Input Clamp Diode Voltage Output HIGH Voltage 2.7 0.65 3.5 0.25 VO OL Output LOW Voltage 0.35 IIH IIL IOS ICC Input HIGH Current 0.1 Input LOW Current Short Circuit Current (Note 1) Power Supply Current 20 0.4 100 13 0.5 20 V A mA mA mA mA IOL = 8.0 mA 0.4 Min 2.0 0.8 1.5 Typ Max Unit V V V V V Test Conditions Guaranteed Input HIGH Voltage for All Inputs Guaranteed Input LOW Voltage for All Inputs VCC = MIN, IIN = 18 mA VCC = MIN, IOH = MAX, VIN = VIH or VIL per Truth Table IOL = 4.0 mA VCC = VCC MIN, VIN = VIL or VIH per Truth Table

VCC = MAX, VIN = 2.7 V VCC = MAX, VIN = 7.0 V VCC = MAX, VIN = 0.4 V VCC = MAX VCC = MAX

Note 1: Not more than one output should be shorted at a time, nor for more than 1 second.

AC CHARACTERISTICS (TA = 25C)

Limits Symbol tPLH tPHL tPLH tPHL Parameter Propagation Delay (2 Levels) Propagation Delay (3 Levels) Min Typ 15 15 20 20 Max 25 25 30 30 Unit ns ns Test Conditions Figure 2 Figure 1 VCC = 5.0 V CL = 15 pF

AC WAVEFORMS

VIN

1.3 V tPHL

1.3 V tPLH 1.3 V 1.3 V

VIN

1.3 V tPHL

1.3 V tPLH 1.3 V

VOUT

VOUT

1.3 V

Figure 1.

Figure 2.

http://onsemi.com
48

SN74LS47 BCD to 7-Segment Decoder/Driver

The SN74LS47 are Low Power Schottky BCD to 7-Segment Decoder/ Drivers consisting of NAND gates, input buffers and seven AND-OR-INVERT gates. They offer active LOW, high sink current outputs for driving indicators directly. Seven NAND gates and one driver are connected in pairs to make BCD data and its complement available to the seven decoding AND-OR-INVERT gates. The remaining NAND gate and three input buffers provide lamp test, blanking input / ripple-blanking output and ripple-blanking input. The circuits accept 4-bit binary-coded-decimal (BCD) and, depending on the state of the auxiliary inputs, decodes this data to drive a 7-segment display indicator. The relative positive-logic output levels, as well as conditions required at the auxiliary inputs, are shown in the truth tables. Output configurations of the SN74LS47 are designed to withstand the relatively high voltages required for 7-segment indicators. These outputs will withstand 15 V with a maximum reverse current of 250 A. Indicator segments requiring up to 24 mA of current may be driven directly from the SN74LS47 high performance output transistors. Display patterns for BCD input counts above nine are unique symbols to authenticate input conditions. The SN74LS47 incorporates automatic leading and / or trailing-edge zero-blanking control (RBI and RBO). Lamp test (LT) may be performed at any time which the BI / RBO node is a HIGH level. This device also contains an overriding blanking input (BI) which can be used to control the lamp intensity by varying the frequency and duty cycle of the BI input signal or to inhibit the outputs. Lamp Intensity Modulation Capability (BI/RBO) Open Collector Outputs Lamp Test Provision Leading/ Trailing Zero Suppression Input Clamp Diodes Limit High-Speed Termination Effects
GUARANTEED OPERATING RANGES
Symbol VCC TA IOH IOL Parameter Supply Voltage Operating Ambient Temperature Range Output Current High BI/RBO Output Current Low BI/RBO BI/RBO OffState Output Voltage a to g OnState Output Current a to g Min 4.75 0 Typ 5.0 25 Max 5.25 70 50 3.2 Unit V C

http://onsemi.com

LOW POWER SCHOTTKY

16 1

PLASTIC N SUFFIX CASE 648

16 1

SOIC D SUFFIX CASE 751B

ORDERING INFORMATION
Device SN74LS47N SN74LS47D Package 16 Pin DIP 16 Pin Shipping 2000 Units/Box 2500/Tape & Reel

mA
mA

VO(off) IO(on)

15 24

V mA

Semiconductor Components Industries, LLC, 1999

49

December, 1999 Rev. 6

Publication Order Number: SN74LS47/D

SN74LS47
CONNECTION DIAGRAM DIP (TOP VIEW)
VCC 16 f 15 g 14 a 13 b 12 c 11 d 10 e 9

1 B

2 C

6 D

7 A

8 GND

LT BI / RBO RBI

LOADING (Note a) PIN NAMES A, B, C, D RBI LT BI/RBO a, to g BCD Inputs RippleBlanking Input LampTest Input Blanking Input or RippleBlanking Output Outputs HIGH 0.5 U.L. 0.5 U.L. 0.5 U.L. 0.5 U.L. 1.2 U.L. OpenCollector LOW 0.25 U.L. 0.25 U.L. 0.25 U.L. 0.75 U.L. 2.0 U.L. 15 U.L.

NOTES: a) 1 Unit Load (U.L.) = 40 mA HIGH, 1.6 mA LOW. b) Output current measured at VOUT = 0.5 V b) The Output LOW drive factor is 15 U.L. for Commercial (74) Temperature Ranges.

LOGIC SYMBOL
7 1 2 6 3 5

A B C D LT RBI BI/ f g RBO

b c d

13 12 11 10 9 15 14 4 VCC = PIN 16 GND = PIN 8

http://onsemi.com
50

SN74LS47

LOGIC DIAGRAM
a A b B INPUT C D d BLANKING INPUT OR RIPPLE-BLANKING OUTPUT d c c OUTPUT b a

f LAMP-TEST INPUT RIPPLE-BLANKING INPUT

10 11 12 13 14 15

NUMERICAL DESIGNATIONS RESULTANT DISPLAYS

TRUTH TABLE
INPUTS DECIMAL OR FUNCTION 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 BI RBI LT OUTPUTS

LT H H H H H H H H H H H H H H H H X H L

RBI H X X X X X X X X X X X X X X X X L X

D L L L L L L L L H H H H H H H H X L X

C L L L L H H H H L L L L H H H H X L X

B L L H H L L H H L L H H L L H H X L X

A L H L H L H L H L H L H L H L H X L X

BI/RBO H H H H H H H H H H H H H H H H L L H

a L H L L H L H L L L H H H L H H H H L

b L L L L L H H L L L H H L H H H H H L

c L L H L L L L L L L H L H H H H H H L

d L H L L H L L H L H L L H L L H H H L

e L H L H H H L H L H L H H H L H H H L

f L H H H L L L H L L H H L L L H H H L

g H H L L L L L H L L L L L L L H H H L

NOTE A A

B C D

H = HIGH Voltage Level L = LOW Voltage Level X = Immaterial NOTES: (A) BI/RBO is wire-AND logic serving as blanking Input (BI) and/or ripple-blanking output (RBO). The blanking out (BI) must be open or held at a HIGH level when output functions 0 through 15 are desired, and ripple-blanking input (RBI) must be open or at a HIGH level if blanking of a decimal 0 is not desired. X = input may be HIGH or LOW. (B) When a LOW level is applied to the blanking input (forced condition) all segment outputs go to a LOW level regardless of the state of any other input condition. (C) When ripple-blanking input (RBI) and inputs A, B, C, and D are at LOW level, with the lamp test input at HIGH level, all segment outputs go to a HIGH level and the ripple-blanking output (RBO) goes to a LOW level (response condition). (D) When the blanking input/ripple-blanking output (BI/RBO) is open or held at a HIGH level, and a LOW level is applied to lamp test input, all segment outputs go to a LOW level.

http://onsemi.com
51

SN74LS47
DC CHARACTERISTICS OVER OPERATING TEMPERATURE RANGE (unless otherwise specified)
Limits Symbol VIH VIL VIK VO OH VO OL IO (off) VO (on) ( ) IIH IIL IOS BI / RBO ICC Parameter Input HIGH Voltage Input LOW Voltage Input Clamp Diode Voltage Output HIGH Voltage BI / RBO Voltage, Output LOW Voltage g BI / RBO Off-State Output Current a thru g On-State Output Voltage g a thru g Input HIGH Current Input LOW Current BI / RBO Any Input except BI / RBO Output Short Circuit Current (Note 1) Power Supply Current 0.3 7.0 0.25 0.35 2.4 24 0.65 4.2 42 0.25 0.35 0.4 0.5 250 0.4 0.5 20 0.1 1.2 0.4 2.0 13 Min 2.0 0.8 1.5 Typ Max Unit V V V V V V A V V A mA mA mA mA Test Conditions Guaranteed Input HIGH Theshold Voltage for All Inputs Guaranteed Input LOW Threshold Voltage for All Inputs VCC = MIN, IIN = 18 mA VCC = MIN, IOH = 50 A, VIN = VIN or VIL per Truth Table IOL = 1.6 mA IOL = 3.2 mA VCC = MIN, VIN = VIN or VIL per Truth Table

VCC = MAX, VIN = VIN or VIL per Truth Table, VO (off) = 15 V IO (on) = 12 mA IO (on) = 24 mA VCC = MAX, VIN = VIH or VIL per Truth Table

VCC = MAX, VIN = 2.7 V VCC = MAX, VIN = 7.0 V VCC = MAX, VIN = 0.4 V VCC = MAX, VOUT = 0 V VCC = MAX

Note 1: Not more than one output should be shorted at a time, nor for more than 1 second.

AC CHARACTERISTICS (TA = 25C)

Limits Symbol tPHL tPLH tPHL tPLH Parameter Propagation Delay, Address Input to Segment Output Propagation Delay, RBI Input To Segment Output Min Typ Max 100 100 100 100 Unit ns ns ns ns Test Conditions VCC = 5.0 V CL = 15 pF

AC WAVEFORMS

VIN

1.3 V tPHL

1.3 V tPLH 1.3 V 1.3 V

VIN

1.3 V tPHL

1.3 V tPLH 1.3 V

VOUT

VOUT

1.3 V

Figure 1.

Figure 2.

http://onsemi.com
52

SN74LS74A Dual D-Type Positive Edge-Triggered Flip-Flop

The SN74LS74A dual edge-triggered flip-flop utilizes Schottky TTL circuitry to produce high speed D-type flip-flops. Each flip-flop has individual clear and set inputs, and also complementary Q and Q outputs. Information at input D is transferred to the Q output on the positive-going edge of the clock pulse. Clock triggering occurs at a voltage level of the clock pulse and is not directly related to the transition time of the positive-going pulse. When the clock input is at either the HIGH or the LOW level, the D input signal has no effect.
http://onsemi.com

LOW POWER SCHOTTKY

MODE SELECT TRUTH TABLE

INPUTS OPERATING MODE SD Set Reset (Clear) *Undetermined Load 1 (Set) Load 0 (Reset) * L H L H H SD H L L H H D X X X h l Q H L H H L Q L H H L H
14 1

OUTPUTS

PLASTIC N SUFFIX CASE 646

Both outputs will be HIGH while both SD and CD are LOW, but the output states are unpredictable if SD and CD go HIGH simultaneously. If the levels at the set and clear are near VIL maximum then we cannot guarantee to meet the minimum level for VOH.
14 1

H, h = HIGH Voltage Level L, I = LOW Voltage Level X = Dont Care l, h (q) = Lower case letters indicate the state of the referenced input i, h (q) = (or output) one set-up time prior to the HIGH to LOW clock transition.

SOIC D SUFFIX CASE 751A

GUARANTEED OPERATING RANGES

Symbol VCC TA IOH IOL Parameter Supply Voltage Operating Ambient Temperature Range Output Current High Output Current Low Min 4.75 0 Typ 5.0 25 Max 5.25 70 0.4 8.0 Unit V C mA mA

ORDERING INFORMATION
Device SN74LS74AN SN74LS74AD Package 14 Pin DIP 14 Pin Shipping 2000 Units/Box 2500/Tape & Reel

Semiconductor Components Industries, LLC, 1999

53

December, 1999 Rev. 6

Publication Order Number: SN74LS74A/D

SN74LS74A
LOGIC DIAGRAM (Each Flip-Flop)

SET (SD) 4 (10) Q 5 (9) CLEAR (CD) 1 (13) CLOCK 3 (11) D 2 (12)

Q 6 (8)

LOGIC SYMBOL
4 2 3 D SD Q CP CD Q 1 VCC = PIN 14 GND = PIN 7 6 5 12 11 10 D SD Q CP CD Q 13 8 9

http://onsemi.com
54

SN74LS74A
DC CHARACTERISTICS OVER OPERATING TEMPERATURE RANGE (unless otherwise specified)
Limits Symbol VIH VIL VIK VOH Parameter Input HIGH Voltage Input LOW Voltage Input Clamp Diode Voltage Output HIGH Voltage 2.7 0.65 3.5 0.25 VO OL Output LOW Voltage 0.35 Input High Current Data, Clock Set, Clear Data, Clock Set, Clear IIL IOS ICC Input LOW Current Data, Clock Set, Clear Output Short Circuit Current (Note 1) Power Supply Current 20 0.5 20 40 0.1 0.2 0.4 0.8 100 8.0 V A IOL = 8.0 mA 0.4 Min 2.0 0.8 1.5 Typ Max Unit V V V V V Test Conditions Guaranteed Input HIGH Voltage for All Inputs Guaranteed Input LOW Voltage for All Inputs VCC = MIN, IIN = 18 mA VCC = MIN, IOH = MAX, VIN = VIH or VIL per Truth Table IOL = 4.0 mA VCC = VCC MIN, VIN = VIL or VIH per Truth Table

VCC = MAX, VIN = 2.7 V

IIH

mA

VCC = MAX, VIN = 7.0 V

mA mA mA

VCC = MAX, VIN = 0.4 V VCC = MAX VCC = MAX

Note 1: Not more than one output should be shorted at a time, nor for more than 1 second.

AC CHARACTERISTICS (TA = 25C, VCC = 5.0 V)

Limits Symbol fMAX tPLH tPHL Parameter Maximum Clock Frequency Clock, Clear, Clock Clear Set to Output Min 25 Typ 33 13 25 25 40 Max Unit MHz ns ns Test Conditions Figure 1 Figure 1 VCC = 5.0 V 50 F CL = 15 pF

AC SETUP REQUIREMENTS (TA = 25C)

Limits Symbol tW (H) tW (L) ts th Clock Clear, Set Data Setup Time HIGH Data Setup Time LOW Hold Time Parameter Min 25 25 20 20 5.0 Typ Max Unit ns ns ns Figure 1 ns ns Figure 1 Test Conditions Figure 1 Figure 2 VCC = 5.0 V

http://onsemi.com
55

SN74LS74A
AC WAVEFORMS

D*

1.3 V th(L) ts(L) 1.3 V tW(H)

1.3 V th(H) ts(H) tW(L) 1.3 V 1 fMAX

CP tPHL Q 1.3 V tPHL

tPLH 1.3 V

tPLH 1.3 V Q

1.3 V

*The shaded areas indicate when the input is permitted to change for predictable output performance.

Figure 1. Clock to Output Delays, Data Set-Up and Hold Times, Clock Pulse Width

tW SET 1.3 V 1.3 V tW CLEAR tPLH 1.3 V tPHL Q

1.3 V tPHL 1.3 V tPLH

1.3 V

1.3 V

1.3 V

Figure 2. Set and Clear to Output Delays, Set and Clear Pulse Widths

http://onsemi.com
56

SN74LS76A Dual JK Flip-Flop with Set and Clear

The SN74LS76A offers individual J, K, Clock Pulse, Direct Set and Direct Clear inputs. These dual flip-flops are designed so that when the clock goes HIGH, the inputs are enabled and data will be accepted. The Logic Level of the J and K inputs will perform according to the Truth Table as long as minimum set-up times are observed. Input data is transferred to the outputs on the HIGH-to-LOW clock transitions.
http://onsemi.com

LOW POWER SCHOTTKY

MODE SELECT TRUTH TABLE

OPERATING MODE Set Reset (Clear) *Undetermined Toggle Load 0 (Reset) Load 1 (Set) Hold * INPUTS SD L H L H H H H CD H L L H H H H J X X X h l h l K X X X h h l l OUTPUTS Q H L H q L H q Q L H H q H L q

16 1

Both outputs will be HIGH while both SD and CD are LOW, but the output states are unpredictable if SD and CD go HIGH simultaneously.

PLASTIC N SUFFIX CASE 648

H, h = HIGH Voltage Level L, I = LOW Voltage Level X = Immaterial l, h (q) = Lower case letters indicate the state of the referenced input i, h (q) = (or output) one setup time prior to the HIGHtoLOW clock transition
16 1

SOIC D SUFFIX CASE 751B

GUARANTEED OPERATING RANGES

Symbol VCC TA IOH IOL Parameter Supply Voltage Operating Ambient Temperature Range Output Current High Output Current Low Min 4.75 0 Typ 5.0 25 Max 5.25 70 0.4 8.0 Unit V C mA mA

ORDERING INFORMATION
Device SN74LS76AN SN74LS76AD Package 16 Pin DIP 16 Pin Shipping 2000 Units/Box 2500/Tape & Reel

Semiconductor Components Industries, LLC, 1999

57

December, 1999 Rev. 6

Publication Order Number: SN74LS76A/D

SN74LS76A
LOGIC DIAGRAM
2 Q Q 16 1 4 CLEAR (CD) J SET (SD) K K CP J C Q D 3 VCC = PIN 5 GND = PIN 13 CLOCK (CP) 14 SD Q 15 12 6 9 K CP J C Q D 8 10

LOGIC SYMBOL
7 SD Q 11

DC CHARACTERISTICS OVER OPERATING TEMPERATURE RANGE (unless otherwise specified)

Limits Symbol VIH VIL VIK VOH Parameter Input HIGH Voltage Input LOW Voltage Input Clamp Diode Voltage Output HIGH Voltage 2.7 0.65 3.5 0.25 VO OL Output LOW Voltage 0.35 J, K Clear Clock IIH Input HIGH Current J, K Clear Clock Input LOW Current Short Circuit Current (Note 1) Power Supply Current J, K Clear, Clock 20 0.1 0.3 0.4 0.4 0.8 100 6.0 mA VCC = MAX, VIN = 7.0 V 0.5 20 60 80 V A IOL = 8.0 mA 0.4 Min 2.0 0.8 1.5 Typ Max Unit V V V V V Test Conditions Guaranteed Input HIGH Voltage for All Inputs Guaranteed Input LOW Voltage for All Inputs VCC = MIN, IIN = 18 mA VCC = MIN, IOH = MAX, VIN = VIH or VIL per Truth Table IOL = 4.0 mA VCC = VCC MIN, VIN = VIL or VIH per Truth Table

VCC = MAX, VIN = 2.7 V

IIL IOS ICC

mA mA mA

VCC = MAX, VIN = 0.4 V VCC = MAX VCC = MAX

Note 1: Not more than one output should be shorted at a time, nor for more than 1 second.

AC CHARACTERISTICS (TA = 25C, VCC = 5.0 V)

Limits Symbol fMAX tPLH tPHL Parameter Maximum Clock Frequency Clock, Clear, Clock Clear Set to Output 15 20 ns Min 30 Typ 45 15 20 Max Unit MHz ns VCC = 5.0 V 50 CL = 15 pF F Test Conditions

AC SETUP REQUIREMENTS (TA = 25C)

Limits Symbol tW tW ts th Parameter Clock Pulse Width High Clear Set Pulse Width Setup Time Hold Time Min 20 25 20 0 Typ Max Unit ns ns ns ns VCC = 5 0 V 5.0 Test Conditions

http://onsemi.com
58

SN74LS85 4-Bit Magnitude Comparator

The SN74LS85 is a 4-Bit Magnitude Camparator which compares two 4-bit words (A, B), each word having four Parallel Inputs (A0 A3, B0 B3); A3, B3 being the most significant inputs. Operation is not restricted to binary codes, the device will work with any monotonic code. Three Outputs are provided: A greater than B (OA > B), A less than B (OA < B), A equal to B (OA = B). Three Expander Inputs, IA > B, IA < B, IA = B, allow cascading without external gates. For proper compare operation, the Expander Inputs to the least significant position must be connected as follows: IA < B= IA > B = L, IA = B = H. For serial (ripple) expansion, the OA > B, OA < B and OA = B Outputs are connected respectively to the IA > B, IA < B, and IA = B Inputs of the next most significant comparator, as shown in Figure 1. Refer to Applications section of data sheet for high speed method of comparing large words. The Truth Table on the following page describes the operation of the SN74LS85 under all possible logic conditions. The upper 11 lines describe the normal operation under all conditions that will occur in a single device or in a series expansion scheme. The lower five lines describe the operation under abnormal conditions on the cascading inputs. These conditions occur when the parallel expansion technique is used. Easily Expandable Binary or BCD Comparison OA > B, OA < B, and OA = B Outputs Available
GUARANTEED OPERATING RANGES
Symbol VCC TA IOH IOL Parameter Supply Voltage Operating Ambient Temperature Range Output Current High Output Current Low Min 4.75 0 Typ 5.0 25 Max 5.25 70 0.4 8.0 Unit V C mA mA

http://onsemi.com

LOW POWER SCHOTTKY

16 1

PLASTIC N SUFFIX CASE 648

16 1

SOIC D SUFFIX CASE 751B

ORDERING INFORMATION
Device SN74LS85N SN74LS85D Package 16 Pin DIP 16 Pin Shipping 2000 Units/Box 2500/Tape & Reel

Semiconductor Components Industries, LLC, 1999

59

December, 1999 Rev. 6

Publication Order Number: SN74LS85/D

SN74LS85
CONNECTION DIAGRAM DIP (TOP VIEW)
VCC 16 A3 15 B2 14 A2 13 A1 12 B1 11 A0 10 B0 9 NOTE: The Flatpak version has the same pinouts (Connection Diagram) as the Dual In-Line Package. 1 B3 2 IA<B 3 IA=B 4 IA>B 5 6 8 7 OA<B GND LOADING (Note a) PIN NAMES A0 A3, B0 B3 IA = B IA < B, IA > B OA > B OA < B OA = B Parallel Inputs A = B Expander Inputs A < B, A > B, Expander Inputs A Greater than B Output B Greater than A Output A Equal to B Output HIGH 1.5 U.L. 1.5 U.L. 0.5 U.L. 10 U.L. 10 U.L. 10 U.L. LOW 0.75 U.L. 0.75 U.L. 0.25 U.L. 5 U.L. 5 U.L. 5 U.L.

OA>B OA=B

NOTES: a) 1 TTL Unit Load (U.L.) = 40 mA HIGH/1.6 mA LOW.

LOGIC SYMBOL
10 12 13 15 9 11 14 1 4 2 3 A0 A1 A2 A3 B0 B1 B2 B3 IA>B OA>B IA<B OA<B IA=B OA=B VCC = PIN 16 GND = PIN 8 5 7 6

http://onsemi.com
60

SN74LS85
LOGIC DIAGRAM
(15) (1)

A3 B3

(5) (13)

OA>B

(14) (2) A<B (3) A=B (4) A>B (12) (11)

A2 B2

(6)

OA=B

A1 B1

(7)

OA<B

A0 B0

(10) (9)

TRUTH TABLE
COMPARING INPUTS A3,B3 A3>B3 A3<B3 A3=B3 A3=B3 A3=B3 A3=B3 A3=B3 A3=B3 A3=B3 A3=B3 A3=B3 A3=B3 A3=B3 A2,B2 X X A2>B2 A2<B2 A2=B2 A2=B2 A2=B2 A2=B2 A2=B2 A2=B2 A2=B2 A2=B2 A2=B2 A1,B1 X X X X A1>B1 A1<B1 A1=B1 A1=B1 A1=B1 A1=B1 A1=B1 A1=B1 A1=B1 A0,B0 X X X X X X A0>B0 A0<B0 A0=B0 A0=B0 A0=B0 A0=B0 A0=B0 CASCADING INPUTS IA>B X X X X X X X X H L X H L IA<B X X X X X X X X L H X H L IA=B X X X X X X X X L L H L L OA>B H L H L H L H L H L L L H OUTPUTS OA<B L H L H L H L H L H L L H OA=B L L L L L L L L L L H L L

H = HIGH Level L = LOW Level X = IMMATERIAL

http://onsemi.com
61

SN74LS85
A n3 A n2 A n1 B n3 B n2 B n1 An A0 A1 A2 A3 B0 B1 B2 A0 A1 A2 A3 B0 B1 B2 B3 B3 OA > B OA < B OA = B Bn B3 OA > B OA < B OA = B

A0 A1 A2 A3 B0 B1 B2 IA > B IA < B IA = B

L L H

IA > B IA < B IA = B

SN74LS85

SN74LS85

A>B A<B A=B

L = LOW LEVEL H = HIGH LEVEL

Figure 1. Comparing Two n-Bit Words

APPLICATIONS Figure 2 shows a high speed method of comparing two 24-bit words with only two levels of device delay. With the technique shown in Figure 1, six levels of device delay result
Table 1
WORD LENGTH 1 4 Bits 5 24 Bits 25 120 Bits NUMBER OF PKGS. 1 26 8 31

when comparing two 24-bit words. The parallel technique can be expanded to any number of bits, see Table 1.

NOTE: The SN74LS85 can be used as a 5-bit comparator only when the outputs are used to drive the A0A3 and B0B3 inputs of another SN74LS85 as shown in Figure 2 in positions #1, 2, 3, and 4.

INPUTS (LSB) A0 A1 A2 A3 B0 B1 B2 B3 A0 A1 A2 A3 B0 B1 B2 B3 IA > B OA > B IA < B IA = B #5 OA < B OA = B (MSB) A20 A21 A22 A23 B20 B21 B22 B23 A0 A1 A2 A3 B0 B1 B2 B3 IA > B OA > B IA < B IA = B #1 OA < B OA = B NC

L L H

A19 B19 L

INPUTS

A5 A6 A7 A8 B5 B6 B7 B8 A0 A1 A2 A3 B0 B1 B2 B3 OA > B #4 IA < B OA < B IA > B IA = B OA = B NC

A10 A11 A12 A13 B10 B11 B12 B13 A0 A1 A2 A3 B0 B1 B2 B3 OA > B #3 OA < B IA < B IA > B IA = B OA = B NC

A15 A16 A17 A18 B15 B16 B17 B18 A0 A1 A2 A3 B0 B1 B2 B3 OA > B #2 OA < B IA < B IA > B IA = B OA = B NC

A4 B4 L

A9 B9 L

A14 B14 L

A0 A1 A2 A3 B0 B1 B2 B3 IA > B OA > B IA < B IA = B #6 OA < B OA = B OUTPUTS

MSB = MOST SIGNIFICANT BIT LSB = LEAST SIGNIFICANT BIT L = LOW LEVEL H = HIGH LEVEL NC = NO CONNECTION

Figure 2. Comparison of Two 24-Bit Words http://onsemi.com

62

SN74LS85
DC CHARACTERISTICS OVER OPERATING TEMPERATURE RANGE (unless otherwise specified)
Limits Symbol VIH VIL VIK VOH Parameter Input HIGH Voltage Input LOW Voltage Input Clamp Diode Voltage Output HIGH Voltage 2.7 0.65 3.5 0.25 VO OL Output LOW Voltage 0.35 Input HIGH Current A < B, A > B Other Inputs A < B, A > B Other Inputs IIL IOS ICC Input LOW Current A < B, A > B Other Inputs Output Short Circuit Current (Note 1) Power Supply Current 20 0.5 V A IOL = 8.0 mA 0.4 Min 2.0 0.8 1.5 Typ Max Unit V V V V V Test Conditions Guaranteed Input HIGH Voltage for All Inputs Guaranteed Input LOW Voltage for All Inputs VCC = MIN, IIN = 18 mA VCC = MIN, IOH = MAX, VIN = VIH or VIL per Truth Table IOL = 4.0 mA VCC = VCC MIN, VIN = VIL or VIH per Truth Table

IIH

20 60 0.1 0.3 0.4 1.2 100 20

VCC = MAX, VIN = 2.7 V

mA

VCC = MAX, VIN = 7.0 V

mA mA mA

VCC = MAX, VIN = 0.4 V VCC = MAX VCC = MAX

Note 1: Not more than one output should be shorted at a time, nor for more than 1 second.

AC CHARACTERISTICS (TA = 25C, VCC = 5.0 V)

Limits Symbol tPLH tPHL tPLH tPHL tPLH tPHL tPLH tPHL tPLH tPHL Parameter Any A or B to A < B, A > B Any A or B to A = B A < B or A = B to A > B A = B to A = B A > B or A = B to A < B Min Typ 24 20 27 23 14 11 13 13 14 11 Max 36 30 45 45 22 17 20 26 22 17 Unit ns ns ns ns ns VCC = 5.0 V CL = 15 pF Test Conditions

AC WAVEFORMS

VIN

1.3 V tPHL

1.3 V tPLH 1.3 V

VIN

1.3 V tPHL

1.3 V tPLH 1.3 V

VOUT

1.3 V

VOUT

1.3 V

Figure 3.

Figure 4.

http://onsemi.com
63

SN74LS86 Quad 2-Input Exclusive OR Gate

VCC 14 13 12 11 10 9 8

http://onsemi.com

LOW POWER SCHOTTKY

1 2 3 4 5 6 7 GND

TRUTH TABLE
IN A L L H H B L H L H OUT Z L H H L
14 1

PLASTIC N SUFFIX CASE 646

GUARANTEED OPERATING RANGES

Symbol VCC TA IOH IOL Parameter Supply Voltage Operating Ambient Temperature Range Output Current High Output Current Low Min 4.75 0 Typ 5.0 25 Max 5.25 70 0.4 8.0 Unit V C mA mA
14 1

SOIC D SUFFIX CASE 751A

ORDERING INFORMATION
Device SN74LS86N SN74LS86D Package 14 Pin DIP 14 Pin Shipping 2000 Units/Box 2500/Tape & Reel

Semiconductor Components Industries, LLC, 1999

64

December, 1999 Rev. 6

Publication Order Number: SN74LS86/D

SN74LS86
DC CHARACTERISTICS OVER OPERATING TEMPERATURE RANGE (unless otherwise specified)
Limits Symbol VIH VIL VIK VOH Parameter Input HIGH Voltage Input LOW Voltage Input Clamp Diode Voltage Output HIGH Voltage 2.7 0.65 3.5 0.25 VO OL Output LOW Voltage 0.35 IIH IIL IOS ICC Input HIGH Current 0.2 Input LOW Current Short Circuit Current (Note 1) Power Supply Current 20 0.8 100 10 0.5 40 V A mA mA mA mA IOL = 8.0 mA 0.4 Min 2.0 0.8 1.5 Typ Max Unit V V V V V Test Conditions Guaranteed Input HIGH Voltage for All Inputs Guaranteed Input LOW Voltage for All Inputs VCC = MIN, IIN = 18 mA VCC = MIN, IOH = MAX, VIN = VIH or VIL per Truth Table IOL = 4.0 mA VCC = VCC MIN, VIN = VIL or VIH per Truth Table

VCC = MAX, VIN = 2.7 V VCC = MAX, VIN = 7.0 V VCC = MAX, VIN = 0.4 V VCC = MAX VCC = MAX

Note 1: Not more than one output should be shorted at a time, nor for more than 1 second.

AC CHARACTERISTICS (TA = 25C)

Limits Symbol tPLH tPHL tPLH tPHL Parameter Propagation Delay, Other Input LOW Propagation Delay, Other Input HIGH Min Typ 12 10 20 13 Max 23 17 30 22 Unit ns ns VCC = 5.0 V CL = 15 pF Test Conditions

http://onsemi.com
65

SN74LS109A Dual JK Positive Edge-Triggered Flip-Flop

The SN74LS109A consists of two high speed completely independent transition clocked JK flip-flops. The clocking operation is independent of rise and fall times of the clock waveform. The JK design allows operation as a D flip-flop by simply connecting the J and K pins together.
http://onsemi.com

MODE SELECT TRUTH TABLE

INPUTS OPERATING MODE SD Set Reset (Clear) *Undetermined Load 1 (Set) Hold Toggle Load 0 (Reset) * L H L H H H H CD H L L H H H H J X X X h l h l K X X X h h l l Q H L H H q q L Q L H H L q q H OUTPUTS

LOW POWER SCHOTTKY

16 1

Both outputs will be HIGH while both SD and CD are LOW, but the output states are unpredictable if SD and CD go HIGH simultaneously.

H, h = HIGH Voltage Level L, I = LOW Voltage Level X = Dont Care l, h (q) = Lower case letters indicate the state of the referenced input i, h (q) = (or output) one set-up time prior to the LOW to HIGH clock transition.
16

PLASTIC N SUFFIX CASE 648

GUARANTEED OPERATING RANGES

Symbol VCC TA IOH IOL Parameter Supply Voltage Operating Ambient Temperature Range Output Current High Output Current Low Min 4.75 0 Typ 5.0 25 Max 5.25 70 0.4 8.0 Unit V C mA mA

SOIC D SUFFIX CASE 751B

ORDERING INFORMATION
Device SN74LS109AN SN74LS109AD Package 16 Pin DIP 16 Pin Shipping 2000 Units/Box 2500/Tape & Reel

Semiconductor Components Industries, LLC, 1999

66

December, 1999 Rev. 6

Publication Order Number: SN74LS109A/D

SN74LS109A
LOGIC DIAGRAM
SET (SD) 5(11) CLEAR (CD) 1(15) CLOCK 4(12)

Q 6(10)

Q 7(9) J 2(14) K 3(13)

LOGIC SYMBOL
5 2 4 3 J SD Q CP K C Q D 1 VCC = PIN 16 GND = PIN 8 7 6 14 12 13 11 J SD Q CP K C Q D 15 9 10

DC CHARACTERISTICS OVER OPERATING TEMPERATURE RANGE (unless otherwise specified)

Limits Symbol VIH VIL VIK VOH Parameter Input HIGH Voltage Input LOW Voltage Input Clamp Diode Voltage Output HIGH Voltage 2.7 0.65 3.5 0.25 VO OL Output LOW Voltage 0.35 Input HIGH Current J, K, Clock Set, Clear J, K, Clock Set, Clear IIL IOS ICC Input LOW Current J, K, Clock Set, Clear Output Short Circuit Current (Note 1) Power Supply Current 20 0.5 20 40 0.1 0.2 0.4 0.8 100 8.0 V A IOL = 8.0 mA 0.4 Min 2.0 0.8 1.5 Typ Max Unit V V V V V Test Conditions Guaranteed Input HIGH Voltage for All Inputs Guaranteed Input LOW Voltage for All Inputs VCC = MIN, IIN = 18 mA VCC = MIN, IOH = MAX, VIN = VIH or VIL per Truth Table IOL = 4.0 mA VCC = VCC MIN, VIN = VIL or VIH per Truth Table

VCC = MAX, VIN = 2.7 V

IIH

mA

VCC = MAX, VIN = 7.0 V

mA mA mA

VCC = MAX, VIN = 0.4 V VCC = MAX VCC = MAX

Note 1: Not more than one output should be shorted at a time, nor for more than 1 second.

http://onsemi.com
67

SN74LS109A
AC CHARACTERISTICS (TA = 25C, VCC = 5.0 V)
Limits Symbol fMAX tPLH tPHL Parameter Maximum Clock Frequency Clock Clear Set to Output Clock, Clear, Min 25 Typ 33 13 25 25 40 Max Unit MHz ns ns VCC = 5.0 V 50 CL = 15 pF F Test Conditions

AC SETUP REQUIREMENTS (TA = 25C, VCC = 5.0 V)

Limits Symbol tW ts th Parameter Clock High Clear, Set Pulse Width Data Setup Time HIGH Data Setup Time LOW Hold time Min 25 20 20 5.0 Typ Max Unit ns ns ns ns VCC = 5 0 V 5.0 Test Conditions

http://onsemi.com
68

SN74LS122 SN74LS123 Retriggerable Monostable Multivibrators

These dc triggered multivibrators feature pulse width control by three methods. The basic pulse width is programmed by selection of external resistance and capacitance values. The LS122 has an internal timing resistor that allows the circuits to be used with only an external capacitor. Once triggered, the basic pulse width may be extended by retriggering the gated low-level-active (A) or high-level-active (B) inputs, or be reduced by use of the overriding clear. Overriding Clear Terminates Output Pulse Compensated for VCC and Temperature Variations DC Triggered from Active-High or Active-Low Gated Logic Inputs Retriggerable for Very Long Output Pulses, up to 100% Duty Cycle Internal Timing Resistors on LS122
http://onsemi.com

LOW POWER SCHOTTKY

14 1

PLASTIC N SUFFIX CASE 646

GUARANTEED OPERATING RANGES

Symbol VCC TA IOH IOL Rext Cext Rext/Cext Parameter Supply Voltage Operating Ambient Temperature Range Output Current High Output Current Low External Timing Resistance External Capacitance Wiring Capacitance at Rext/Cext Terminal 5.0 Min 4.75 0 Typ 5.0 25 Max 5.25 70 0.4 8.0 260 No Restriction 50 pF Unit V C mA mA k
14 1

SOIC D SUFFIX CASE 751A

W
16 1

PLASTIC N SUFFIX CASE 648

16 1

SOIC D SUFFIX CASE 751B

ORDERING INFORMATION
Device SN74LS122N SN74LS122D SN74LS123N SN74LS123D Package 14 Pin DIP 14 Pin 16 Pin DIP 16 Pin Shipping 2000 Units/Box 2500/Tape & Reel 2000 Units/Box 2500/Tape & Reel

Semiconductor Components Industries, LLC, 1999

69

December, 1999 Rev. 6

Publication Order Number: SN74LS122/D

SN74LS122 SN74LS123
SN74LS123 (TOP VIEW) (SEE NOTES 1 THRU 4)
VCC 16 1 Rext/ 1 Cext Cext 15 14 1Q 13 2Q 12 2 CLR 11 2B 10 2A 9

Q CLR Q 1 1A 2 1B 3 1 CLR 4 1Q 5 2Q

Q Q

CLR

6 2 Cext

8 7 2 GND Rext/ Cext

SN74LS122 (TOP VIEW) (SEE NOTES 1 THRU 4)

VCC 14 Rext/ Cext 13 NC 12 Cext 11 NC 10 Rint Q CLR Q 1 A1 2 A2 3 B1 4 B2 5 CLR 6 Q 7 GND Rint 9 Q 8

NC NO INTERNAL CONNECTION.

NOTES: 1. An external timing capacitor may be connected between Cext and Rext/Cext (positive). 2. To use the internal timing resistor of the LS122, connect Rint to VCC. 3. For improved pulse width accuracy connect an external resistor between Rext/Cext and VCC with Rint open-circuited. 4. To obtain variable pulse widths, connect an external variable resistance between Rint/Cext and VCC.

http://onsemi.com
70

SN74LS122 SN74LS123
LS122 FUNCTIONAL TABLE
INPUTS CLEAR L X X X H H H H H H H A1 X H X X L L X X H L X A2 X H X X X X L L H X L B1 X X L X H H H H H H H B2 X X X L H H H H H H H OUTPUTS Q L L L L Q H H H H CLEAR L X X H H

LS123 FUNCTIONAL TABLE

INPUTS A X H X L L B X X L H H OUTPUTS Q L L L Q H H H

TYPICAL APPLICATION DATA The output pulse tW is a function of the external components, Cext and Rext or Cext and Rint on the LS122. For values of Cext 1000 pF, the output pulse at VCC = 5.0 V and VRC = 5.0 V (see Figures 1, 2, and 3) is given by tW = K Rext Cext where K is nominally 0.45 If Cext is on pF and Rext is in k then tW is in nanoseconds. The Cext terminal of the LS122 and LS123 is an internal connection to ground, however for the best system performance Cext should be hard-wired to ground. Care should be taken to keep Rext and Cext as close to the monostable as possible with a minimum amount of inductance between the Rext/Cext junction and the Rext/Cext pin. Good groundplane and adequate bypassing should be designed into the system for optimum performance to ensure that no false triggering occurs. It should be noted that the Cext pin is internally connected to ground on the LS122 and LS123, but not on the LS221. Therefore, if Cext is hard-wired externally to ground, substitution of a LS221 onto a LS123 socket will cause the LS221 to become non-functional. The switching diode is not needed for electrolytic capacitance application and should not be used on the LS122 and LS123. To find the value of K for Cext 1000 pF, refer to Figure 4. Variations on VCC or VRC can cause the value of K to change, as can the temperature of the LS123, LS122.

Figures 5 and 6 show the behavior of the circuit shown in Figures 1 and 2 if separate power supplies are used for VCC and VRC. If VCC is tied to VRC, Figure 7 shows how K will vary with VCC and temperature. Remember, the changes in Rext and Cext with temperature are not calculated and included in the graph. As long as Cext 1000 pF and 5K Rext 260K, the change in K with respect to Rext is negligible. If Cext 1000 pF the graph shown on Figure 8 can be used to determine the output pulse width. Figure 9 shows how K will change for Cext 1000 pF if VCC and VRC are connected to the same power supply. The pulse width tW in nanoseconds is approximated by tW = 6 + 0.05 Cext (pF) + 0.45 Rext (k) Cext + 11.6 Rext In order to trim the output pulse width, it is necessary to include a variable resistor between VCC and the Rext/Cext pin or between VCC and the Rext pin of the LS122. Figure 10, 11, and 12 show how this can be done. Rext remote should be kept as close to the monostable as possible. Retriggering of the part, as shown in Figure 3, must not occur before Cext is discharged or the retrigger pulse will not have any effect. The discharge time of Cext in nanoseconds is guaranteed to be less than 0.22 Cext (pF) and is typically 0.05 Cext (pF). For the smallest possible deviation in output pulse widths from various devices, it is suggested that Cext be kept 1000 pF.

http://onsemi.com
71

SN74LS122 SN74LS123

WAVEFORMS

RETRIGGER PULSE B INPUT

(See Application Data)

Q OUTPUT tW OUTPUT WITHOUT RETRIGGER

EXTENDING PULSE WIDTH

B INPUT

CLEAR INPUT

CLEAR PULSE

OUTPUT WITHOUT CLEAR PULSE Q OUTPUT

OVERRIDING THE OUTPUT PULSE

http://onsemi.com
72

SN74LS122 SN74LS123
DC CHARACTERISTICS OVER OPERATING TEMPERATURE RANGE (unless otherwise specified)
Limits Symbol VIH VIL VIK VOH Parameter Input HIGH Voltage Input LOW Voltage Input Clamp Diode Voltage Output HIGH Voltage 2.7 0.65 3.5 0.25 VO OL Output LOW Voltage 0.35 IIH IIL IOS ICC Input HIGH Current 0.1 Input LOW Current Short Circuit Current (Note 1) LS122 Power Supply Current LS123 20 20 0.4 100 11 mA VCC = MAX 0.5 20 V A mA mA mA IOL = 8.0 mA 0.4 Min 2.0 0.8 1.5 Typ Max Unit V V V V V Test Conditions Guaranteed Input HIGH Voltage for All Inputs Guaranteed Input LOW Voltage for All Inputs VCC = MIN, IIN = 18 mA VCC = MIN, IOH = MAX, VIN = VIH or VIL per Truth Table IOL = 4.0 mA VCC = VCC MIN, VIN = VIL or VIH per Truth Table

VCC = MAX, VIN = 2.7 V VCC = MAX, VIN = 7.0 V VCC = MAX, VIN = 0.4 V VCC = MAX

Note 1: Not more than one output should be shorted at a time, nor for more than 1 second.

AC CHARACTERISTICS (TA = 25C, VCC = 5.0 V)

Limits Symbol tPLH tPHL tPLH tPHL tPLH tPHL tW min tWQ Parameter Propagation Delay, A to Q g y Propagation Delay, A to Q Propagation Delay, B to Q g y Propagation Delay, B to Q Propagation Delay, Clear to Q g y Propagation Delay, Clear to Q A or B to Q A to B to Q 4.0 Min Typ 23 32 23 34 28 20 116 4.5 Max 33 ns 45 44 ns 56 45 ns 27 200 5.0 ns s Cext = 1000 pF, Rext = 10 k, CL = 15 pF, RL = 2.0 k Rext = 5.0 k RL = 2.0 k Cext = 0 CL = 15 pF Unit Test Conditions

AC SETUP REQUIREMENTS (TA = 25C, VCC = 5.0 V)

Limits Symbol tW Pulse Width Parameter Min 40 Typ Max Unit ns Test Conditions

http://onsemi.com
73

SN74LS122 SN74LS123
VCC VRC Rext Cext Cext Rext/ VCC Cext Q CLR 1/2 LS123 B Pin 51 A Q GND 0.1 F Pout VCC VCC VRC Rext Cext Cext Rext/ VCC CLR Cext Q B2 LS122 B1 A2 Q A1 GND 0.1 F VCC

Pout

Pin 51

Figure 1.

Figure 2.

Pin

Pout

tW

RETRIGGER

Figure 3.

10 5K Rext 260K EXTERNAL CAPACITANCE, Cext ( F) 1

0.1

0.01

0.001

0.3

0.35 0.4

0.45 0.5

0.55

Figure 4.

http://onsemi.com
74

SN74LS122 SN74LS123
0.55 VRC = 5 V Cext = 1000 pF 0.5 0.5 55C 0C 25C 70C 0.4 125C 0.4 125C 0.4 0C 0.55 VCC = 5 V Cext = 1000 pF 0.5 55C 0.55 Cext = 1000 pF

55C 25C

K
0.45

K
0.45 70C

K
0.45

0C 25C 70C 125C

0.35 4.5 5 VCC 5.5

0.35 4.5 5 VRC 5.5

0.35 4.5 5 VCC = VRC 5.5

Figure 5. K versus VCC

Figure 6. K versus VRC

Figure 7. K versus VCC and VRC

100000

10000 t W, OUTPUT PULSE WIDTH (ns)

Rext = 260 k Rext = 160 k

1000

100

Rext = 80 k Rext = 40 k Rext = 20 k Rext = 10 k Rext = 5 k 1 10 100 1000

10

Cext, EXTERNAL TIMING CAPACITANCE (pF)

Figure 8.

http://onsemi.com
75

SN74LS122 SN74LS123
0.65

Cext = 200 pF 55C 0.6 0C 25C

70C K 0.55

125C

0.5

4.5

4.75

5 VCC VOLTS

5.25

5.5

Figure 9.

VCC Rext REMOTE

PIN 7 OR 15 Cext PIN 6 OR 14

Rext

Figure 10. LS123 Remote Trimming Circuit

http://onsemi.com
76

SN74LS122 SN74LS123
VCC PIN 9 OPEN Rext PIN 13 Cext PIN 11 Rext REMOTE

Figure 11. LS122 Remote Trimming Circuit Without Rext

VCC Rext REMOTE

PIN 9 PIN 13

PIN 11

Figure 12. LS122 Remote Trimming Circuit with Rint

http://onsemi.com
77

SN74LS125A SN74LS126A Quad 3-State Buffers

VCC 14 E 13 D 12 O 11 E 10 D 9 O 8

http://onsemi.com

1 E

2 D

3 O

4 E

5 D

6 O

7 GND

LOW POWER SCHOTTKY

LS125A
VCC 14 E 13 D 12 O 11 E 10 D 9 O 8
14 1

PLASTIC N SUFFIX CASE 646 1 E 2 D 3 O 4 E 5 D 6 O 7 GND

LS126A TRUTH TABLES LS125A

INPUTS E L L H D L H X OUTPUT L H (Z) INPUTS E H H L D L H X OUTPUT L H (Z)
14

LS126A

SOIC D SUFFIX CASE 751A

L = LOW Voltage Level H = HIGH Voltage Level X = Dont Care (Z) = High Impedance (off)

ORDERING INFORMATION
Device Package 14 Pin DIP 14 Pin 14 Pin DIP 14 Pin Shipping 2000 Units/Box 2500/Tape & Reel 2000 Units/Box 2500/Tape & Reel

GUARANTEED OPERATING RANGES

Symbol VCC TA IOH IOL Parameter Supply Voltage Operating Ambient Temperature Range Output Current High Output Current Low Min 4.75 0 Typ 5.0 25 Max 5.25 70 2.6 24 Unit V C mA mA

SN74LS125AN SN74LS125AD SN74LS126AN SN74LS126AD

Semiconductor Components Industries, LLC, 1999

78

December, 1999 Rev. 6

Publication Order Number: SN74LS125A/D

SN74LS125A SN74LS126A
DC CHARACTERISTICS OVER OPERATING TEMPERATURE RANGE (unless otherwise specified)
Limits Symbol VIH VIL VIK VOH Parameter Input HIGH Voltage Input LOW Voltage Input Clamp Diode Voltage Output HIGH Voltage 2.4 0.25 VO OL IOZH IOZL IIH IIL IOS ICC Output LOW Voltage 0.35 Output Off Current HIGH Output Off Current LOW Input HIGH Current 0.1 Input LOW Current Short Circuit Current (Note 1) LS125A Power Supply Current LS126A 22 40 0.4 225 20 mA VCC = MAX 0.5 20 20 20 V A A A mA mA mA IOL = 24 mA 0.4 0.65 Min 2.0 0.8 1.5 Typ Max Unit V V V V V Test Conditions Guaranteed Input HIGH Voltage for All Inputs Guaranteed Input LOW Voltage for All Inputs VCC = MIN, IIN = 18 mA VCC = MIN, IOH = MAX, VIN = VIH or VIL per Truth Table IOL = 12 mA VCC = VCC MIN, VIN = VIL or VIH per Truth Table

VCC = MAX, VOUT = 2.4 V VCC = MAX, VOUT = 0.4 V VCC = MAX, VIN = 2.7 V VCC = MAX, VIN = 7.0 V VCC = MAX, VIN = 0.4 V VCC = MAX VIN = 0 V, VE = 4.5 V VIN = 0 V, VE = 0 V

Note 1: Not more than one output should be shorted at a time, nor for more than 1 second.

AC CHARACTERISTICS (TA = 25C)

Limits Symbol tPLH tPLH tPHL tPHL tPZH Output Enable Time to HIGH Level Output Enable Time to LOW Level Output Disable Time from HIGH Level Output Disable Time from LOW Level Propagation Delay, g y Data to Output Parameter LS125A LS126A LS125A LS126A LS125A LS126A LS125A LS126A LS125A LS126A LS125A LS126A Min Typ 9.0 9.0 7.0 8.0 12 16 15 21 Max 15 15 ns 18 18 20 ns 25 25 ns 35 20 ns 25 20 ns 25 FIgures 3, 5 3 Figures 4 5 4, VCC = 5.0 V CL = 5 0 pF 5.0 F RL = 667 Figures 3 5 3, Figures 4 5 4, VCC = 5.0 V CL = 45 pF F RL = 667 Figure 2 Unit Test Conditions

tPZL

tPHZ

tPLZ

http://onsemi.com
79

SN74LS125A SN74LS126A
VIN VIN

1.3 V tPLH 1.3 V

1.3 V tPHL 1.3 V

1.3 V tPHL

1.3 V tPLH 1.3 V

VOUT

1.3 V

VOUT

Figure 1.

Figure 2.

VE 1.3 V VE tPZL VOUT 1.3 V tPLZ 1.3 V VOL 0.5 V 1.3 V

VE 1.3 V tPZH 1.3 V tPHZ > VOH 1.3 V 0.5 V 1.3 V

VE

VOUT

Figure 3.

Figure 4.

VCC

RL

SW1

TO OUTPUT UNDER TEST

5 k SW2

CL

Figure 5.

SWITCH POSITIONS
SYMBOL tPZH tPZL tPLZ tPHZ SW1 Open Closed Closed Closed SW2 Closed Open Closed Closed

http://onsemi.com
80

SN74LS132 Quad 2-Input Schmitt Trigger NAND Gate

The SN74LS132 contains four 2-Input NAND Gates which accept standard TTL input signals and provide standard TTL output levels. They are capable of transforming slowly changing input signals into sharply defined, jitter-free output signals. Additionally, they have greater noise margin than conventional NAND Gates. Each circuit contains a 2-input Schmitt trigger followed by a Darlington level shifter and a phase splitter driving a TTL totem pole output. The Schmitt trigger uses positive feedback to effectively speed-up slow input transitions, and provide different input threshold voltages for positive and negative-going transitions. This hysteresis between the positive-going and negative-going input thresholds (typically 800 mV) is determined internally by resistor ratios and is essentially insensitive to temperature and supply voltage variations. As long as one input remains at a more positive voltage than VT+ (MAX), the gate will respond to the transitions of the other input as shown in Figure 1.
http://onsemi.com

LOW POWER SCHOTTKY

14 1

LOGIC AND CONNECTION DIAGRAM DIP (TOP VIEW)

VCC 14 13 12 11 10 9 8

PLASTIC N SUFFIX CASE 646

14 1

7 GND

SOIC D SUFFIX CASE 751A

GUARANTEED OPERATING RANGES

Symbol VCC TA IOH IOL Parameter Supply Voltage Operating Ambient Temperature Range Output Current High Output Current Low Min 4.75 0 Typ 5.0 25 Max 5.25 70 0.4 8.0 Unit V C mA mA

ORDERING INFORMATION
Device SN74LS132N SN74LS132D Package 14 Pin DIP 14 Pin Shipping 2000 Units/Box 2500/Tape & Reel

Semiconductor Components Industries, LLC, 1999

81

December, 1999 Rev. 6

Publication Order Number: SN74LS132/D

SN74LS132
5 VO, OUTPUT VOLTAGE (VOLTS) 4

VCC = 5 V TA = 25C

0.4

0.95 1.2 VIN, INPUT VOLTAGE (VOLTS)

1.8

Figure 1. VIN versus VOUT Transfer Function

DC CHARACTERISTICS OVER OPERATING TEMPERATURE RANGE (unless otherwise specified)

Limits Symbol VT+ VT VT + VT VIK VOH VO OL IT+ IT IIH IIL IOS ICC Parameter Positive-Going Threshold Voltage Negative-Going Threshold Voltage Hysteresis Input Clamp Diode Voltage Output HIGH Voltage Output LOW Voltage 0.35 Input Current at Positive-Going Threshold Input Current at Negative-Going Threshold Input HIGH Current 0.1 Input LOW Current Output Short Circuit Current Power Supply Current Total, Output HIGH Total, Output LOW
(1)

Min 1.5 0.6 0.4

Typ

Max 2.0 1.1

Unit V V V

Test Conditions VCC = 5.0 V VCC = 5.0 V VCC = 5.0 V VCC = MIN, IIN = 18 mA VCC = MIN, IOH = 400 A, VIN = VIL VCC = MIN, IOL = 4.0 mA, VIN = 2.0 V VCC = MIN, IOL = 8.0 mA, VIN = 2.0 V VCC = 5.0 V, VIN = VT+ VCC = 5.0 V, VIN = VT VCC = MAX, VIN = 2.7 V VCC = MAX, VIN = 7.0 V VCC = MAX, VIN = 0.4 V VCC = MAX, VOUT = 0 V VCC = MAX, VIN = 0 V VCC = MAX, VIN = 4.5 V

0.8 0.65 1.5

V V

2.7

3.4 0.25 0.4 0.5

V V mA mA

0.14 0.18 20

A mA mA mA mA mA

0.4 20 5.9 8.2 100 11 14

Note 1: Not more than one output should be shorted at a time, nor for more than 1 second.

AC CHARACTERISTICS (TA = 25C)

Limits Symbol tPLH tPHL Parameter Turn-Off Delay, Input to Output Turn-On Delay, Input to Output Min Typ Max 22 22 Unit ns ns Test Conditions VCC = 5.0 V CL = 15 pF

http://onsemi.com
82

SN74LS132
3V VIN 0V tPHL tPLH 1.6 V 0.8 V

VOUT

1.3 V

1.3 V

Figure 2. AC Waveforms

V T, THRESHOLD VOLTAGE (VOLTS) V T, HYSTERESIS (VOLTS)

TA = 25C VT+

1.6

1.2 VT 0.8 VT

0.4

4.5

4.75 5 5.25 VCC, POWER SUPPLY VOLTAGE (VOLTS)

5.5

Figure 3. Threshold Voltage and Hysteresis versus Power Supply Voltage

V T, THRESHOLD VOLTAGE (VOLTS) V T, HYSTERESIS (VOLTS)

1.9 1.7 1.5 1.3 1.1 0.9 0.7 55 VT VT 0 25 75 TA, AMBIENT TEMPERATURE (C) VT+

125

Figure 4. Threshold Voltage and Hysteresis versus Temperature

http://onsemi.com
83

SN74LS138 1-of-8 Decoder/ Demultiplexer

The LSTTL / MSI SN74LS138 is a high speed 1-of-8 Decoder / Demultiplexer. This device is ideally suited for high speed bipolar memory chip select address decoding. The multiple input enables allow parallel expansion to a 1-of-24 decoder using just three LS138 devices or to a 1-of-32 decoder using four LS138s and one inverter. The LS138 is fabricated with the Schottky barrier diode process for high speed and is completely compatible with all ON Semiconductor TTL families. Demultiplexing Capability Multiple Input Enable for Easy Expansion Typical Power Dissipation of 32 mW Active Low Mutually Exclusive Outputs Input Clamp Diodes Limit High Speed Termination Effects
GUARANTEED OPERATING RANGES
Symbol VCC TA IOH IOL Parameter Supply Voltage Operating Ambient Temperature Range Output Current High Output Current Low Min 4.75 0 Typ 5.0 25 Max 5.25 70 0.4 8.0 Unit V C mA mA
16 1

http://onsemi.com

LOW POWER SCHOTTKY

16 1

PLASTIC N SUFFIX CASE 648

SOIC D SUFFIX CASE 751B

ORDERING INFORMATION
Device SN74LS138N SN74LS138D Package 16 Pin DIP 16 Pin Shipping 2000 Units/Box 2500/Tape & Reel

Semiconductor Components Industries, LLC, 1999

84

December, 1999 Rev. 6

Publication Order Number: SN74LS138/D

SN74LS138
CONNECTION DIAGRAM DIP (TOP VIEW)
VCC 16 O0 15 O1 14 O2 13 O3 12 O4 11 O5 10 O6 9 NOTE: The Flatpak version has the same pinouts (Connection Diagram) as the Dual In-Line Package. 1 A0 2 A1 3 A2 4 E1 5 E2 6 E3 7 O7 8 GND

LOADING (Note a) PIN NAMES A0 A2 E1, E2 E3 O0 O7 Address Inputs Enable (Active LOW) Inputs Enable (Active HIGH) Input Active LOW Outputs HIGH 0.5 U.L. 0.5 U.L. 0.5 U.L. 10 U.L. LOW 0.25 U.L. 0.25 U.L. 0.25 U.L. 5 U.L.

NOTES: a) 1 TTL Unit Load (U.L.) = 40 mA HIGH/1.6 mA LOW.

LOGIC SYMBOL
1 2 3 456 1 23 A0 A1 A2 E

O0 O1 O2 O3 O4 O5 O6 O7

15 14 13 12 11 10 9 7 VCC = PIN 16 GND = PIN 8

http://onsemi.com
85

SN74LS138
LOGIC DIAGRAM
A2
3 2

A1
1

A0
4

E1 E2 E3
5 6

VCC = PIN 16 GND = PIN 8 = Pin Numbers

10

11

12

13

14

15

O7

O6

O5

O4

O3

O2

O1

O0

http://onsemi.com
86

SN74LS138
FUNCTIONAL DESCRIPTION

The LS138 is a high speed 1-of-8 Decoder/Demultiplexer fabricated with the low power Schottky barrier diode process. The decoder accepts three binary weighted inputs (A0, A1, A2) and when enabled provides eight mutually exclusive active LOW Outputs (O0 O7). The LS138 features three Enable inputs, two active LOW (E1, E2) and one active HIGH (E3). All outputs will be HIGH unless E1 and E2 are LOW and E3 is HIGH. This multiple enable

function allows easy parallel expansion of the device to a 1-of-32 (5 lines to 32 lines) decoder with just four LS138s and one inverter. (See Figure a.) The LS138 can be used as an 8-output demultiplexer by using one of the active LOW Enable inputs as the data input and the other Enable inputs as strobes. The Enable inputs which are not used must be permanently tied to their appropriate active HIGH or active LOW state.

TRUTH TABLE
INPUTS E1 H X X L L L L L L L L E2 X H X L L L L L L L L E3 X X L H H H H H H H H A0 X X X L H L H L H L H A1 X X X L L H H L L H H A2 X X X L L L L H H H H O0 H H H L H H H H H H H O1 H H H H L H H H H H H O2 H H H H H L H H H H H OUTPUTS O3 H H H H H H L H H H H O4 H H H H H H H L H H H O5 H H H H H H H H L H H O6 H H H H H H H H H L H O7 H H H H H H H H H H L

H = HIGH Voltage Level L = LOW Voltage Level X = Dont Care

A0 A1 A2 LS04 A3 A4 H 123 A0 A1 A2 LS138 O0 O1 O2 O3 O4 O5 O6 O7 E A0 A1 A2 LS138 O0 O1 O2 O3 O4 O5 O6 O7 123 E A0 A1 A2 LS138 O0 O1 O2 O3 O4 O5 O6 O7 123 E A0 A1 A2 LS138 O0 O1 O2 O3 O4 O5 O6 O7 123 E

O0

O31

Figure a

http://onsemi.com
87

SN74LS138
DC CHARACTERISTICS OVER OPERATING TEMPERATURE RANGE (unless otherwise specified)
Limits Symbol VIH VIL VIK VOH Parameter Input HIGH Voltage Input LOW Voltage Input Clamp Diode Voltage Output HIGH Voltage 2.7 0.65 3.5 0.25 VO OL Output LOW Voltage 0.35 IIH IIL IOS ICC Input HIGH Current 0.1 Input LOW Current Short Circuit Current (Note 1) Power Supply Current 20 0.4 100 10 0.5 20 V A mA mA mA mA IOL = 8.0 mA 0.4 Min 2.0 0.8 1.5 Typ Max Unit V V V V V Test Conditions Guaranteed Input HIGH Voltage for All Inputs Guaranteed Input LOW Voltage for All Inputs VCC = MIN, IIN = 18 mA VCC = MIN, IOH = MAX, VIN = VIH or VIL per Truth Table IOL = 4.0 mA VCC = VCC MIN, VIN = VIL or VIH per Truth Table

VCC = MAX, VIN = 2.7 V VCC = MAX, VIN = 7.0 V VCC = MAX, VIN = 0.4 V VCC = MAX VCC = MAX

Note 1: Not more than one output should be shorted at a time, nor for more than 1 second.

AC CHARACTERISTICS (TA = 25C)

Symbol tPLH tPHL tPLH tPHL tPLH tPHL tPLH tPHL Parameter Propagation Delay Address to Output Propagation Delay Address to Output Propagation Delay E1 or E2 Enable to Output Propagation Delay E3 Enable to Output Levels of Delay 2 2 3 3 2 2 3 3 Limits Min Typ 13 27 18 26 12 21 17 25 Max 20 41 27 39 18 32 26 38 Unit ns ns ns ns Test Conditions

VCC = 5.0 V CL = 15 pF

AC WAVEFORMS
VIN tPLH 1.3 V VOUT

VIN

1.3 V tPHL

1.3 V

1.3 V tPHL 1.3 V tPLH

1.3 V

VOUT

1.3 V

1.3 V

Figure 1.

Figure 2.

http://onsemi.com
88

SN74LS139 Dual 1-of-4 Decoder/ Demultiplexer

The LSTTL/MSI SN74LS139 is a high speed Dual 1-of-4 Decoder/Demultiplexer. The device has two independent decoders, each accepting two inputs and providing four mutually exclusive active LOW Outputs. Each decoder has an active LOW Enable input which can be used as a data input for a 4-output demultiplexer. Each half of the LS139 can be used as a function generator providing all four minterms of two variables. The LS139 is fabricated with the Schottky barrier diode process for high speed and is completely compatible with all ON Semiconductor TTL families.
http://onsemi.com

LOW POWER SCHOTTKY

Schottky Process for High Speed Multifunction Capability Two Completely Independent 1-of-4 Decoders Active Low Mutually Exclusive Outputs Input Clamp Diodes Limit High Speed Termination Effects ESD > 3500 Volts

16 1

GUARANTEED OPERATING RANGES

Symbol VCC TA IOH IOL Parameter Supply Voltage Operating Ambient Temperature Range Output Current High Output Current Low Min 4.75 0 Typ 5.0 25 Max 5.25 70 0.4 8.0 Unit V C mA mA
16

PLASTIC N SUFFIX CASE 648

SOIC D SUFFIX CASE 751B

ORDERING INFORMATION
Device SN74LS139N SN74LS139D Package 16 Pin DIP 16 Pin Shipping 2000 Units/Box 2500/Tape & Reel

Semiconductor Components Industries, LLC, 1999

89

December, 1999 Rev. 6

Publication Order Number: SN74LS139/D

SN74LS139
CONNECTION DIAGRAM DIP (TOP VIEW)
VCC 16 Eb 15 A0b 14 A1b 13 O0b 12 O1b 11 O2b 10 O3b 9 NOTE: The Flatpak version has the same pinouts (Connection Diagram) as the Dual In-Line Package. 1 Ea 2 A0a 3 A1a 4 O0a 5 O1a 6 O2a 7 O3a 8 GND

LOADING (Note a) PIN NAMES A0, A1 E O0 O3 Address Inputs Enable (Active LOW) Input Active LOW Outputs HIGH 0.5 U.L. 0.5 U.L. 10 U.L. LOW 0.25 U.L. 0.25 U.L. 5 U.L.

NOTES: a) 1 TTL Unit Load (U.L.) = 40 mA HIGH/1.6 mA LOW.

LOGIC SYMBOL
1 2 3 15 14 13

A0 A1

A0 A1

DECODER a O0 O1 O2 O3

DECODER b O0 O1 O2 O3

4 5 6 7

12 11 10 9

VCC = PIN 16 GND = PIN 8

http://onsemi.com
90

SN74LS139
LOGIC DIAGRAM
Ea
1 2

A0a A1a
3 15

Eb

A0b A1b
14 13

VCC = PIN 16 GND = PIN 8 = PIN NUMBERS

12

11

10

O0a

O1a

O2a

O3a

O0b

O1b

O2b

O3b

FUNCTIONAL DESCRIPTION

The LS139 is a high speed dual 1-of-4 decoder/ demultiplexer fabricated with the Schottky barrier diode process. The device has two independent decoders, each of which accept two binary weighted inputs (A0, A1) and provide four mutually exclusive active LOW outputs (O0 O3). Each decoder has an active LOW Enable (E). When E is HIGH all outputs are forced HIGH. The enable

can be used as the data input for a 4-output demultiplexer application. Each half of the LS139 generates all four minterms of two variables. These four minterms are useful in some applications, replacing multiple gate functions as shown in Fig. a, and thereby reducing the number of packages required in a logic network.

TRUTH TABLE
INPUTS E H L L L L A0 X L H L H A1 X L L H H O0 H L H H H OUTPUTS O1 H H L H H O2 H H H L H O3 H H H H L E A0 A1 E A0 A1 E A0 A1 E A0 A1 O0 E A0 A1 E A0 A1 E A0 A1 E A0 A1 O0

O1

O1

O2

O2

H = HIGH Voltage Level L = LOW Voltage Level X = Dont Care

O3

O3

Figure a

http://onsemi.com
91

SN74LS139
DC CHARACTERISTICS OVER OPERATING TEMPERATURE RANGE (unless otherwise specified)
Limits Symbol VIH VIL VIK VOH Parameter Input HIGH Voltage Input LOW Voltage Input Clamp Diode Voltage Output HIGH Voltage 2.7 0.65 3.5 0.25 VO OL Output LOW Voltage 0.35 IIH IIL IOS ICC Input HIGH Current Input LOW Current Short Circuit Current (Note 1) Power Supply Current 20 0.5 20 0.1 0.4 100 11 V A mA mA mA mA IOL = 8.0 mA 0.4 Min 2.0 0.8 1.5 Typ Max Unit V V V V V Test Conditions Guaranteed Input HIGH Voltage for All Inputs Guaranteed Input LOW Voltage for All Inputs VCC = MIN, IIN = 18 mA VCC = MIN, IOH = MAX, VIN = VIH or VIL per Truth Table IOL = 4.0 mA VCC = VCC MIN, VIN = VIL or VIH per Truth Table

VCC = MAX, VIN = 2.7 V VCC = MAX, VIN = 7.0 V VCC = MAX, VIN = 0.4 V VCC = MAX VCC = MAX

Note 1: Not more than one output should be shorted at a time, nor for more than 1 second.

AC CHARACTERISTICS (TA = 25C)

Symbol tPLH tPHL tPLH tPHL tPLH tPHL Parameter Propagation Delay Address to Output Propagation Delay Address to Output Propagation Delay Enable to Output Levels of Delay 2 2 3 3 2 2 Limits Min Typ 13 22 18 25 16 21 Max 20 33 29 38 24 32 Unit ns ns ns VCC = 5.0 V CL = 15 pF Test Conditions

AC WAVEFORMS
VIN tPLH 1.3 V VOUT

VIN

1.3 V tPHL

1.3 V

1.3 V tPHL 1.3 V tPLH

1.3 V

VOUT

1.3 V

1.3 V

Figure 1.

Figure 2.

http://onsemi.com
92

SN74LS145 1-of-10 Decoder/Driver Open-Collector

The SN74LS145, 1-of-10 Decoder/Driver, is designed to accept BCD inputs and provide appropriate outputs to drive 10-digit incandescent displays. All outputs remain off for all invalid binary input conditions. It is designed for use as indicator/relay drivers or as an open-collector logic circuit driver. Each of the high breakdown output transistors will sink up to 80 mA of current. Typical power dissipation is 35 mW. This device is fully compatible with all TTL families.
http://onsemi.com

Low Power Version of 74145 Input Clamp Diodes Limit High Speed Termination Effects
GUARANTEED OPERATING RANGES
Symbol VCC TA VOH IOL Parameter Supply Voltage Operating Ambient Temperature Range Output Voltage High Output Current Low Min 4.75 0 Typ 5.0 25 Max 5.25 70 15 24 Unit V C V mA
16

LOW POWER SCHOTTKY

PLASTIC N SUFFIX CASE 648

16 1

SOIC D SUFFIX CASE 751B

ORDERING INFORMATION
Device SN74LS145N SN74LS145D Package 16 Pin DIP 16 Pin Shipping 2000 Units/Box 2500/Tape & Reel

Semiconductor Components Industries, LLC, 1999

93

December, 1999 Rev. 6

Publication Order Number: SN74LS145/D

SN74LS145
CONNECTION DIAGRAM DIP (TOP VIEW)
VCC 16 P0 15 P1 14 P2 13 P3 12 Q9 11 Q8 10 Q7 9

1 Q0

2 Q1

3 Q2

4 Q3

5 Q4

6 Q5

Q6 GND LOADING (Note a)

PIN NAMES P0, P1, P2, P3 Q0 Q9 BCD Inputs Outputs

HIGH 0.5 U.L. Open Collector

LOW 0.25 U.L. 15 U.L.

NOTES: a) 1 TTL Unit Load (U.L.) = 40 mA HIGH/1.6 mA LOW.

LOGIC SYMBOL

15 14 13 12 P0 P1 P2 P3

Q0 Q1 Q2 Q3 Q4 Q5 Q6 Q7 Q8 Q9

1 2 3 4 5

6 7 9 10 11

VCC = PIN 16 GND = PIN 8

http://onsemi.com
94

SN74LS145
LOGIC DIAGRAM
INPUTS P0 P1 P2 P3

INPUT INVERTERS 0 0 1 1 2 2 3 3

DECODE/DRIVER GATES Q0 Q1 Q2 Q3 Q4 Q5 Q6 Q7 Q8 Q9

OUTPUTS

TRUTH TABLE
INPUTS P3 L L L L L L L L H H H H H H H H P2 L L L L H H H H L L L L H H H H P1 L L H H L L H H L L H H L L H H P0 L H L H L H L H L H L H L H L H Q0 L H H H H H H H H H H H H H H H Q1 H L H H H H H H H H H H H H H H Q2 H H L H H H H H H H H H H H H H Q3 H H H L H H H H H H H H H H H H OUTPUTS Q4 H H H H L H H H H H H H H H H H Q5 H H H H H L H H H H H H H H H H Q6 H H H H H H L H H H H H H H H H Q7 H H H H H H H L H H H H H H H H Q8 H H H H H H H H L H H H H H H H Q9 H H H H H H H H H L H H H H H H

H = HIGH Voltage Level L = LOW Voltage Level

http://onsemi.com
95

SN74LS145
DC CHARACTERISTICS OVER OPERATING TEMPERATURE RANGE (unless otherwise specified)
Limits Symbol VIH VIL VIK IOH VOL Parameter Input HIGH Voltage Input LOW Voltage Input Clamp Diode Voltage Output HIGH Current 0.25 Output LOW Voltage 0.35 2.3 IIH IIL ICC Input HIGH Current Input LOW Current Power Supply Current 0.65 Min 2.0 0.8 1.5 250 0.4 0.5 3.0 20 0.1 0.4 13 Typ Max Unit V V V A V V V A mA mA mA Test Conditions Guaranteed Input HIGH Voltage for All Inputs Guaranteed Input LOW Voltage for All Inputs VCC = MIN, IIN = 18 mA VCC = MIN, VOH = MAX IOL = 12 mA IOL = 24 mA IOL = 80 mA VCC = VCC MIN, VIN = VIL or VIH per Truth T bl T h Table

VCC = MAX, VIN = 2.7 V VCC = MAX, VIN = 7.0 V VCC = MAX, VIN = 0.4 V VCC = MAX, VIN = GND

AC CHARACTERISTICS (TA = 25C)

Limits Symbol tPHL tPLH Propagation Delay Pn Input to Qn Output Parameter Min Typ Max 50 50 Unit ns Test Conditions VCC = 5.0 V CL = 45 pF

AC WAVEFORMS

VIN

1.3 V tPHL

1.3 V tPLH 1.3 V

VIN

1.3 V tPHL

1.3 V tPLH 1.3 V

VOUT

1.3 V

VOUT

1.3 V

Figure 1.

Figure 2.

http://onsemi.com
96

SN74LS147 SN74LS148 10-Line-to-4-Line and 8-Line-to-3-Line Priority Encoders

The SN74LS147 and the SN74LS148 are Priority Encoders. They provide priority decoding of the inputs to ensure that only the highest order data line is encoded. Both devices have data inputs and outputs which are active at the low logic level. The LS147 encodes nine data lines to four-line (8-4-2-1) BCD. The implied decimal zero condition does not require an input condition because zero is encoded when all nine data lines are at a high logic level. The LS148 encodes eight data lines to three-line (4-2-1) binary (octal). By providing cascading circuitry (Enable Input EI and Enable Output EO) octal expansion is allowed without needing external circuitry.
GUARANTEED OPERATING RANGES
Symbol VCC TA IOH IOL Parameter Supply Voltage Operating Ambient Temperature Range Output Current High Output Current Low Min 4.75 0 Typ 5.0 25 Max 5.25 70 0.4 8.0 Unit V C mA mA

http://onsemi.com

LOW POWER SCHOTTKY

16 1

PLASTIC N SUFFIX CASE 648

16 1

SOIC D SUFFIX CASE 751B

ORDERING INFORMATION
Device SN74LS147N SN74LS147D SN74LS148N SN74LS148D Package 16 Pin DIP 16 Pin 16 Pin DIP 16 Pin Shipping 2000 Units/Box 2500/Tape & Reel 2000 Units/Box 2500/Tape & Reel

Semiconductor Components Industries, LLC, 1999

97

December, 1999 Rev. 6

Publication Order Number: SN74LS147/D

SN74LS147 SN74LS148
SN74LS147 (TOP VIEW)
OUTPUT VCC 16 NC 15 D 14 D 4 5 1 4 2 5 6 3 6 INPUTS 7 4 7 8 5 8 C 6 C B 7 B 8 GND 3 13 3 INPUTS 2 12 2 1 11 1 9 10 9 A OUTPUT A 9

OUTPUTS

SN74LS148 (TOP VIEW)

OUTPUTS VCC 16 EO 15 EO 4 5 1 4 2 5 6 3 6 INPUTS 7 4 7 EI 5 E1 A2 6 A2 GS 14 GS 3 13 3 INPUTS 2 12 2 1 11 1 0 10 0 A0 A1 7 A1 8 GND OUTPUT A0 9

OUTPUTS

http://onsemi.com
98

SN74LS147 SN74LS148
SN74LS147 FUNCTION TABLE
INPUTS 1 H X X X X X X X X L 2 H X X X X X X X L H 3 H X X X X X X L H H 4 H X X X X X L H H H 5 H X X X X L H H H H 6 H X X X L H H H H H 7 H X X L H H H H H H 8 H X L H H H H H H H 9 H L H H H H H H H H D H L L H H H H H H H OUTPUTS C H H H L L L L H H H B H H H L L H H L L H A H L H L H L H L H L EI H L L L L L L L L L 0 X H X X X X X X X L 1 X H X X X X X X L H 2 X H X X X X X L H H 3 X H X X X X L H H H

SN74LS148 FUNCTION TABLE

INPUTS 4 X H X X X L H H H H 5 X H X X L H H H H H 6 X H X L H H H H H H 7 X H L H H H H H H H A2 H H L L L L H H H H OUTPUTS A1 H H L L H H L L H H A0 H H L H L H L H L H GS H H L L L L L L L L EO H L H H H H H H H H

H = HIGH Logic Level, L = LOW Logic Level, X = Irrelevant

FUNCTIONAL BLOCK DIAGRAMS

(11) 0 (12) (9) (13) 2 (1) 3 (2) (7) B 4 (3) 5 (4) (6) A 1

(10) (15) (11) (14) EO GS

(12) (8) (13) (1) (7) A0

4 5

6 7

(2)

A1

(3) C 6 (4) 7 (6)

8 9

(5) (10) (14)

A2

(5) EI

SN74LS147

SN74LS148

http://onsemi.com
99

SN74LS147 SN74LS148
DC CHARACTERISTICS OVER OPERATING TEMPERATURE RANGE (unless otherwise specified)
Limits Symbol VIH VIL VIK VOH Parameter Input HIGH Voltage Input LOW Voltage Input Clamp Diode Voltage Output HIGH Voltage 2.7 0.65 3.5 0.25 VO OL Output LOW Voltage 0.35 Input HIGH Current All Others Inputs 1 7 (LS148) All Others Inputs 1 7 (LS148) IIL IOS ICCH ICCL Input LOW Current All Others Inputs 1 7 (LS148) Short Circuit Current (Note 1) Power Supply Current Output HIGH Output LOW 20 0.5 20 40 0.1 0.2 0.4 0.8 100 17 20 V A IOL = 8.0 mA 0.4 Min 2.0 0.8 1.5 Typ Max Unit V V V V V Test Conditions Guaranteed Input HIGH Voltage for All Inputs Guaranteed Input LOW Voltage for All Inputs VCC = MIN, IIN = 18 mA VCC = MIN, IOH = MAX, VIN = VIH or VIL per Truth Table IOL = 4.0 mA VCC = VCC MIN, VIN = VIL or VIH per Truth Table

VCC = MAX, VIN = 2.7 V

IIH

mA

VCC = MAX, VIN = 7.0 V

mA mA mA mA

VCC = MAX, VIN = 0.4 V VCC = MAX VCC = MAX, All Inputs = 4.5 V VCC = MAX, Inputs 7 & E1 = GND All Other Inputs = 4.5 V

Note 1: Not more than one output should be shorted at a time, nor for more than 1 second.

http://onsemi.com
100

SN74LS147 SN74LS148
AC CHARACTERISTICS (VCC = 5.0 V, TA = 25C) SN74LS147
Symbol tPLH tPHL tPLH tPHL Any Any From (Input) Any To (Output) Any Limits Waveform In-phase output Out-of-phase output Min Typ 12 12 21 15 Max 18 ns 18 33 ns 23 CL = 15 pF, RL = 2.0 k Unit Test Conditions

SN74LS148
Symbol tPLH tPHL tPLH tPHL tPLH tPHL tPLH tPHL tPLH tPHL tPLH tPHL tPLH tPHL EI EO EI GS EI A0, A1, A0 A1 or A2 0 thru 7 GS 0 thru 7 EO 1 thru 7 A0, A1, A0 A1 or A2 From (Input) 1 thru 7 To (Output) A0, A1, A0 A1 or A2 Limits Waveform In-phase output Out-of-phase output Out-of-phase output In-phase output In-phase output In-phase output In- hase In-phase output Min Typ 14 15 20 16 7.0 25 35 9.0 16 12 12 14 12 28 30 Max 18 ns 25 36 ns 29 18 ns 40 55 ns 21 25 ns 25 17 ns 36 21 40 45 ns (LS148) CL = 15 pF, F RL = 2.0 k Unit Test Conditions

http://onsemi.com
101

SN74LS151 8-Input Multiplexer

The TTL / MSI SN74LS151 is a high speed 8-input Digital Multiplexer. It provides, in one package, the ability to select one bit of data from up to eight sources. The LS151 can be used as a universal function generator to generate any logic function of four variables. Both assertion and negation outputs are provided.

http://onsemi.com

Schottky Process for High Speed Multifunction Capability On-Chip Select Logic Decoding Fully Buffered Complementary Outputs Input Clamp Diodes Limit High Speed Termination Effects

LOW POWER SCHOTTKY

GUARANTEED OPERATING RANGES

Symbol VCC TA IOH IOL Parameter Supply Voltage Operating Ambient Temperature Range Output Current High Output Current Low Min 4.75 0 Typ 5.0 25 Max 5.25 70 0.4 8.0 Unit V C mA mA
16 1

PLASTIC N SUFFIX CASE 648

16 1

SOIC D SUFFIX CASE 751B

ORDERING INFORMATION
Device SN74LS151N SN74LS151D Package 16 Pin DIP 16 Pin Shipping 2000 Units/Box 2500/Tape & Reel

Semiconductor Components Industries, LLC, 1999

102

December, 1999 Rev. 6

Publication Order Number: SN74LS151/D

SN74LS151
CONNECTION DIAGRAM DIP (TOP VIEW)
VCC 16 I4 15 I5 14 I6 13 I7 12 S0 11 S1 10 S2 9

1 I3

2 I2

3 I1

4 I0

5 Z

6 Z

7 E

8 GND

LOADING (Note a) PIN NAMES S0 S2 E I0 I7 Z Z Select Inputs Enable (Active LOW) Input Multiplexer Inputs Multiplexer Output Complementary Multiplexer Output HIGH 0.5 U.L. 0.5 U.L. 0.5 U.L. 10 U.L. 10 U.L. LOW 0.25 U.L. 0.25 U.L. 0.25 U.L. 5 U.L. 5 U.L.

NOTES: a) 1 TTL Unit Load (U.L.) = 40 mA HIGH/1.6 mA LOW. b) The Output LOW drive factor is 5 U.L. for Commercial (74) Temperature Ranges.

LOGIC SYMBOL

7 4 3 2 1 15 14 13 12 E I0 I1 I2 I3 I4 I5 I6 I7 S0 S1 S2 Z Z 6 5

11 10 9

VCC = PIN 16 GND = PIN 8

http://onsemi.com
103

SN74LS151
LOGIC DIAGRAM
I0 S2 S1
11 9 10 4

I1
3

I2
2

I3
1

I4
15

I5
14

I6
13

I7
12

S0
7

VCC = PIN 16 GND = PIN 8 = PIN NUMBERS

FUNCTIONAL DESCRIPTION

The LS151 is a logical implementation of a single pole, 8-position switch with the switch position controlled by the state of three Select inputs, S0, S1, S2. Both assertion and negation outputs are provided. The Enable input (E) is active LOW. When it is not activated, the negation output is HIGH and the assertion output is LOW regardless of all other inputs. The logic function provided at the output is:

Z = E (I0 S0 S1 S2 + I1 S0 S1 S2 + I2 S0 S1 S2 + I3 S0 S1 S2 + I4 S0 S1 S2 + I5 S0 S1 S2 + I6 S0 S1 S2 + I7 S0 S1 S2).

The LS151 provides the ability, in one package, to select from eight sources of data or control information. By proper manipulation of the inputs, the LS151 can provide any logic function of four variables and its negation.

TRUTH TABLE
E H L L L L L L L L L L L L L L L L S2 X L L L L L L L L H H H H H H H H S1 X L L L L H H H H L L L L H H H H S0 X L L H H L L H H L L H H L L H H I0 X L H X X X X X X X X X X X X X X I1 X X X L H X X X X X X X X X X X X I2 X X X X X L H X X X X X X X X X X I3 X X X X X X X L H X X X X X X X X I4 X X X X X X X X X L H X X X X X X I5 X X X X X X X X X X X L H X X X X I6 X X X X X X X X X X X X X L H X X I7 X X X X X X X X X X X X X X X L H Z H H L H L H L H L H L H L H L H L Z L L H L H L H L H L H L H L H L H

H = HIGH Voltage Level L = LOW Voltage Level X = Dont Care

http://onsemi.com
104

SN74LS151
DC CHARACTERISTICS OVER OPERATING TEMPERATURE RANGE (unless otherwise specified)
Limits Symbol VIH VIL VIK VOH Parameter Input HIGH Voltage Input LOW Voltage Input Clamp Diode Voltage Output HIGH Voltage 2.7 0.65 3.5 0.25 VO OL Output LOW Voltage 0.35 IIH IIL IOS ICC Input HIGH Current Input LOW Current Short Circuit Current (Note 1) Power Supply Current 20 0.5 20 0.1 0.4 100 10 V A mA mA mA mA 0.4 Min 2.0 0.8 1.5 Typ Max Unit V V V V V Test Conditions Guaranteed Input HIGH Voltage for All Inputs Guaranteed Input LOW Voltage for All Inputs VCC = MIN, IIN = 18 mA VCC = MIN, IOH = MAX, VIN = VIH or VIL per Truth Table IOL = 4.0 mA IOL = 8.0 mA VCC = VCC MIN, VIN = VIL or VIH per Truth Table

VCC = MAX, VIN = 2.7 V VCC = MAX, VIN = 7.0 V VCC = MAX, VIN = 0.4 V VCC = MAX VCC = MAX

Note 1: Not more than one output should be shorted at a time, nor for more than 1 second.

AC CHARACTERISTICS (TA = 25C)

Limits Symbol tPLH tPHL tPLH tPHL tPLH tPHL tPLH tPHL tPLH tPHL tPLH tPHL Parameter Propagation Delay Select to Output Z Propagation Delay Select to Output Z Propagation Delay Enable to Output Z Propagation Delay Enable to Output Z Propagation Delay Data to Output Z Propagation Delay Data to Output Z Min Typ 27 18 14 20 26 20 15 18 20 16 13 12 Max 43 30 23 32 42 32 24 30 32 26 21 20 Unit ns ns ns ns ns ns Test Conditions

VCC = 5.0 V CL = 15 pF

AC WAVEFORMS

VIN

1.3 V tPHL

1.3 V tPLH 1.3 V

VIN

1.3 V tPHL tPLH

1.3 V

VOUT

1.3 V

VOUT

1.3 V

1.3 V

Figure 1.

Figure 2.

http://onsemi.com
105

SN74LS153 Dual 4-Input Multiplexer

The LSTTL / MSI SN74LS153 is a very high speed Dual 4-Input Multiplexer with common select inputs and individual enable inputs for each section. It can select two bits of data from four sources. The two buffered outputs present data in the true (non-inverted) form. In addition to multiplexer operation, the LS153 can generate any two functions of three variables. The LS153 is fabricated with the Schottky barrier diode process for high speed and is completely compatible with all ON Semiconductor TTL families.

http://onsemi.com

Multifunction Capability Non-Inverting Outputs Separate Enable for Each Multiplexer Input Clamp Diodes Limit High Speed Termination Effects

LOW POWER SCHOTTKY

GUARANTEED OPERATING RANGES

Symbol VCC TA IOH IOL Parameter Supply Voltage Operating Ambient Temperature Range Output Current High Output Current Low Min 4.75 0 Typ 5.0 25 Max 5.25 70 0.4 8.0 Unit V C mA mA
16 1

PLASTIC N SUFFIX CASE 648

16 1

SOIC D SUFFIX CASE 751B

ORDERING INFORMATION
Device SN74LS153N SN74LS153D Package 16 Pin DIP 16 Pin Shipping 2000 Units/Box 2500/Tape & Reel

Semiconductor Components Industries, LLC, 1999

106

December, 1999 Rev. 6

Publication Order Number: SN74LS153/D

SN74LS153
CONNECTION DIAGRAM DIP (TOP VIEW)
VCC 16 Eb 15 S0 14 I3b 13 I2b 12 I1b 11 I0b 10 Zb 9 NOTE: The Flatpak version has the same pinouts (Connection Diagram) as the Dual In-Line Package. 1 Ea 2 S1 3 I3a 4 I2a 5 I1a 6 I0a 7 Za 8 GND

LOADING (Note a) PIN NAMES S0 E I0, I1 Z Common Select Input Enable (Active LOW) Input Multiplexer Inputs Multiplexer Output HIGH 0.5 U.L. 0.5 U.L. 0.5 U.L. 10 U.L. LOW 0.25 U.L. 0.25 U.L. 0.25 U.L. 5 U.L.

NOTES: a) 1 TTL Unit Load (U.L.) = 40 mA HIGH/1.6 mA LOW.

LOGIC SYMBOL

6 5 4 3

10 11 12 13 15 I0b I1b I2b I3b Eb

14 2

Ea I0a I1a I2a I3a S0 Sa Za 7

Zb 9

VCC = PIN 16 GND = PIN 8

http://onsemi.com
107

SN74LS153
LOGIC DIAGRAM
Ea I0a
1 6 5

I1a
4

I2a
3

I3a
2

S1
14

S0
10

I0b
11

I1b
12

I2b
13

I3b Eb
15

Za

VCC = PIN 16 GND = PIN 8 = PIN NUMBERS

Zb

FUNCTIONAL DESCRIPTION

The LS153 is a Dual 4-input Multiplexer fabricated with Low Power, Schottky barrier diode process for high speed. It can select two bits of data from up to four sources under the control of the common Select Inputs (S0, S1). The two 4-input multiplexer circuits have individual active LOW Enables (Ea, Eb) which can be used to strobe the outputs independently. When the Enables (Ea, Eb) are HIGH, the corresponding outputs (Za, Zb) are forced LOW. The LS153 is the logic implementation of a 2-pole, 4-position switch, where the position of the switch is determined by the logic levels supplied to the two Select Inputs. The logic equations for the outputs are shown below.

Za = Ea (I0a S1 S0 + I1a S1 S0 + I2a S1 S0 + I3a S1 S0) Zb = Eb (I0b S1 S0 + I1b S1 S0 + I2b S1 S0 + I3b S1 S0)

The LS153 can be used to move data from a group of registers to a common output bus. The particular register from which the data came would be determined by the state of the Select Inputs. A less obvious application is a function generator. The LS153 can generate two functions of three variables. This is useful for implementing highly irregular random logic.

TRUTH TABLE
SELECT INPUTS S0 X L L H H L L H H S1 X L L L L H H H H E H L L L L L L L L INPUTS (a or b) I0 X L H X X X X X X I1 X X X L H X X X X I2 X X X X X L H X X I3 X X X X X X X L H OUTPUT Z L L H L H L H L H

H = HIGH Voltage Level L = LOW Voltage Level X = Dont Care

http://onsemi.com
108

SN74LS153
DC CHARACTERISTICS OVER OPERATING TEMPERATURE RANGE (unless otherwise specified)
Limits Symbol VIH VIL VIK VOH Parameter Input HIGH Voltage Input LOW Voltage Input Clamp Diode Voltage Output HIGH Voltage 2.7 0.65 3.5 0.25 VO OL Output LOW Voltage 0.35 IIH IIL IOS ICC Input HIGH Current 0.1 Input LOW Current Short Circuit Current (Note 1) Power Supply Current 20 0.4 100 10 0.5 20 V A mA mA mA mA IOL = 8.0 mA 0.4 Min 2.0 0.8 1.5 Typ Max Unit V V V V V Test Conditions Guaranteed Input HIGH Voltage for All Inputs Guaranteed Input LOW Voltage for All Inputs VCC = MIN, IIN = 18 mA VCC = MIN, IOH = MAX, VIN = VIH or VIL per Truth Table IOL = 4.0 mA VCC = VCC MIN, VIN = VIL or VIH per Truth Table

VCC = MAX, VIN = 2.7 V VCC = MAX, VIN = 7.0 V VCC = MAX, VIN = 0.4 V VCC = MAX VCC = MAX

Note 1: Not more than one output should be shorted at a time, nor for more than 1 second.

AC CHARACTERISTICS (TA = 25C)

Limits Symbol tPLH tPHL tPLH tPHL tPLH tPHL Parameter Propagation Delay Data to Output Propagation Delay Select to Output Propagation Delay Enable to Output Min Typ 10 17 19 25 16 21 Max 15 26 29 38 24 32 Unit ns ns ns Figure 2 Figure 1 Figure 2 VCC = 5.0 V CL = 15 pF Test Conditions

AC WAVEFORMS

VIN

1.3 V tPHL

1.3 V tPLH 1.3 V

VIN

1.3 V tPHL

1.3 V tPLH 1.3 V

VOUT

1.3 V

VOUT

1.3 V

Figure 1.

Figure 2.

http://onsemi.com
109

SN74LS156 Dual 1-of-4 Decoder/ Demultiplexer

The SN74LS156 is a high speed Dual 1-of-4 Decoder/ Demultiplexer. This device has two decoders with common 2-bit Address inputs and separate gated Enable inputs. Decoder a has an Enable gate with one active HIGH and one active LOW input. Decoder b has two active LOW Enable inputs. If the Enable functions are satisfied, one output of each decoder will be LOW as selected by the address inputs. The LS156 has open collector outputs for wired-OR (DOT-AND) decoding and function generator applications. The LS156 is fabricated with the Schottky barrier diode process for high speed and are completely compatible with all ON Semiconductor TTL families.
http://onsemi.com

LS156OPENCOLLECTOR LOW POWER SCHOTTKY

Schottky Process for High Speed Multifunction Capability Common Address Inputs True or Complement Data Demultiplexing Input Clamp Diodes Limit High Speed Termination Effects ESD > 3500 Volts

16 1

PLASTIC N SUFFIX CASE 648

GUARANTEED OPERATING RANGES

Symbol VCC TA VOH IOL Parameter Supply Voltage Operating Ambient Temperature Range Output Voltage High Output Current Low Min 4.75 0 Typ 5.0 25 Max 5.25 70 5.5 8.0 Unit V C V mA
16 1

SOIC D SUFFIX CASE 751B

ORDERING INFORMATION
Device SN74LS156N SN74LS156D Package 16 Pin DIP 16 Pin Shipping 2000 Units/Box 2500/Tape & Reel

Semiconductor Components Industries, LLC, 1999

110

December, 1999 Rev. 0

Publication Order Number: SN74LS156/D

SN74LS156
CONNECTION DIAGRAM DIP (TOP VIEW)
VCC 16 Eb 15 Eb 14 A0 13 O3b 12 O2b 11 O1b 10 O0b 9 NOTE: The Flatpak version has the same pinouts (Connection Diagram) as the Dual In-Line Package. 1 Ea 2 Ea 3 A1 4 O3a 5 O2a 6 O1a 7 O0a 8 GND

LOADING (Note a) PIN NAMES A0, A1 Ea, Eb Ea O0 O3 Address Inputs Enable (Active LOW) Inputs Enable (Active HIGH) Input Active LOW Outputs HIGH 0.5 U.L. 0.5 U.L. 0.5 U.L. 10 U.L. LOW 0.25 U.L. 0.25 U.L. 0.25 U.L. 5 U.L.

NOTES: a) 1 TTL Unit Load (U.L.) = 40 mA HIGH/1.6 mA LOW.

LOGIC SYMBOL
1 2 13 3 14 15

E DECODER a 0 1 2 3

A0 A1

A0 A1 0 1

E DECODER b 2 3

10 11 12

VCC = PIN 16 GND = PIN 8

http://onsemi.com
111

SN74LS156
LOGIC DIAGRAM
Ea Ea
1 2 13

A0

A1
3 14

Eb Eb
15

10

11

12

O0a

O1a

O2a

O3a

O0b

O1b

O2b

O3b

VCC = PIN 16 GND = PIN 8 = PIN NUMBERS

FUNCTIONAL DESCRIPTION

The LS156 is a Dual 1-of-4 Decoder/Demultiplexer with common Address inputs and separate gated Enable inputs. When enabled, each decoder section accepts the binary weighted Address inputs (A0, A1) and provides four mutually exclusive active LOW outputs (O0 O3). If the Enable requirements of each decoder are not met, all outputs of that decoder are HIGH. Each decoder section has a 2-input enable gate. The enable gate for Decoder a requires one active HIGH input and one active LOW input (EaEa). In demultiplexing applications, Decoder a can accept either true or complemented data by using the Ea or Ea inputs respectively. The enable gate for Decoder b requires two active LOW inputs (EbEb). The LS155 or LS156 can be used as a 1-of-8 Decoder/Demultiplexer by tying Ea to Eb and relabeling the common connection as (A2). The other Eb and Ea are connected together to form the common enable. The LS156 can be used to generate all four minterms of two variables. These four minterms are useful in some applications replacing multiple gate functions as shown in

Fig. a. The LS156 has the further advantage of being able to AND the minterm functions by tying outputs together. Any number of terms can be wired-AND as shown below.
f = (E + A0 + A1) (E + A0 + A1) (E + A0 + A1) (E + A0 + A1) where E = Ea + Ea; E = Eb + Eb
E A0 A1 E A0 A1 E A0 A1 E A0 A1 E O0 A0 A1 E O1 A0 A1 E O2 A0 A1 E O3 A0 A1

O0

O1

O2

O3

Figure a

TRUTH TABLE
ADDRESS A0 X X L H L H A1 X X L L H H ENABLE a Ea L X H H H H Ea X H L L L L O0 H H L H H H OUTPUT a O1 H H H L H H O2 H H H H L H O3 H H H H H L ENABLE b Eb H X L L L L Eb X H L L L L O0 H H L H H H OUTPUT b O1 H H H L H H O2 H H H H L H O3 H H H H H L

H = HIGH Voltage Level L = LOW Voltage Level X = Dont Care

http://onsemi.com
112

SN74LS156
DC CHARACTERISTICS OVER OPERATING TEMPERATURE RANGE (unless otherwise specified)
Limits Symbol VIH VIL VIK IOH VO OL Parameter Input HIGH Voltage Input LOW Voltage Input Clamp Diode Voltage Output HIGH Current 0.25 Output LOW Voltage 0.35 IIH IIL ICC Input HIGH Current 0.1 Input LOW Current Power Supply Current 0.4 10 0.5 20 V A mA mA mA IOL = 8.0 mA 0.65 Min 2.0 0.8 1.5 100 0.4 Typ Max Unit V V V A V Test Conditions Guaranteed Input HIGH Voltage for All Inputs Guaranteed Input LOW Voltage for All Inputs VCC = MIN, IIN = 18 mA VCC = MIN, VOH = MAX IOL = 4.0 mA VCC = VCC MIN, VIN = VIL or VIH per Truth Table

VCC = MAX, VIN = 2.7 V VCC = MAX, VIN = 7.0 V VCC = MAX, VIN = 0.4 V VCC = MAX

AC CHARACTERISTICS (TA = 25C)

Limits Symbol tPLH tPHL tPLH tPHL tPLH tPHL Parameter Propagation Delay Address, Ea or Eb to Output Propagation Delay Address to Output Propagation Delay Ea to Output Min Typ 25 34 31 34 32 32 Max 40 51 46 51 48 48 Unit ns ns ns Figure 1 Figure 2 Figure 1 VCC = 5.0 V CL = 15 pF RL = 2.0 k Test Conditions

AC WAVEFORMS

VIN

1.3 V tPHL

1.3 V tPLH 1.3 V

VIN

1.3 V tPHL

1.3 V tPLH 1.3 V

VOUT

1.3 V

VOUT

1.3 V

Figure 1.

Figure 2.

http://onsemi.com
113

SN74LS157 Quad 2-Input Multiplexer

The LSTTL / MSI SN74LS157 is a high speed Quad 2-Input Multiplexer. Four bits of data from two sources can be selected using the common Select and Enable inputs. The four buffered outputs present the selected data in the true (non-inverted) form. The LS157 can also be used to generate any four of the 16 different functions of two variables. The LS157 is fabricated with the Schottky barrier diode process for high speed and is completely compatible with all ON Semiconductor TTL families.

http://onsemi.com

Schottky Process for High Speed Multifunction Capability Non-Inverting Outputs Input Clamp Diodes Limit High Speed Termination Effects Special Circuitry Ensures Glitch Free Multiplexing ESD > 3500 Volts
16

LOW POWER SCHOTTKY

GUARANTEED OPERATING RANGES

Symbol VCC TA IOH IOL Parameter Supply Voltage Operating Ambient Temperature Range Output Current High Output Current Low Min 4.75 0 Typ 5.0 25 Max 5.25 70 0.4 8.0 Unit V C mA mA

PLASTIC N SUFFIX CASE 648

16 1

SOIC D SUFFIX CASE 751B

ORDERING INFORMATION
Device SN74LS157N SN74LS157D Package 16 Pin DIP 16 Pin Shipping 2000 Units/Box 2500/Tape & Reel

Semiconductor Components Industries, LLC, 1999

114

December, 1999 Rev. 6

Publication Order Number: SN74LS157/D

SN74LS157
CONNECTION DIAGRAM DIP (TOP VIEW)
VCC 16 E 15 I0c 14 I1c 13 Zc 12 I0d 11 I1d 10 Zd 9 NOTE: The Flatpak version has the same pinouts (Connection Diagram) as the Dual In-Line Package. 1 S 2 I0a 3 I1d 4 Za 5 I0b 6 I1b 7 Zb 8 GND

LOADING (Note a) PIN NAMES S E I0a I0d I1a I1d Za Zd Common Select Input Enable (Active LOW) Input Data Inputs from Source 0 Data Inputs from Source 1 Multiplexer Outputs HIGH 1.0 U.L. 1.0 U.L. 0.5 U.L. 0.5 U.L. 10 U.L. LOW 0.5 U.L. 0.5 U.L. 0.25 U.L. 0.25 U.L. 5 U.L.

NOTES: a) 1 TTL Unit Load (U.L.) = 40 mA HIGH/1.6 mA LOW.

LOGIC SYMBOL
15 2 3 5 6 14 13 11 10

E I0a I1a I0b I1b I0c I1c I0d I1d 1 S Za Zb Zc Zd

12

VCC = PIN 16 GND = PIN 8

http://onsemi.com
115

SN74LS157
LOGIC DIAGRAM
I0a
2 3

I1a
5

I0b
6

I1b
14

I0c
13

I1c
11

I0d
10

I1d E S
15 1

12

VCC = PIN 16 GND = PIN 8 = PIN NUMBERS Zd

Za

Zb

Zc

FUNCTIONAL DESCRIPTION

The LS157 is a Quad 2-Input Multiplexer fabricated with the Schottky barrier diode process for high speed. It selects four bits of data from two sources under the control of a common Select Input (S). The Enable Input (E) is active LOW. When E is HIGH, all of the outputs (Z) are forced LOW regardless of all other inputs. The LS157 is the logic implementation of a 4-pole, 2-position switch where the position of the switch is determined by the logic levels supplied to the Select Input. The logic equations for the outputs are:

Za = E (I1a S + I0a S) Zc = E (I1c S + I0c S)

Zb = E (I1b S + I0b S) Zd = E (I1d S + I0d S)

A common use of the LS157 is the moving of data from two groups of registers to four common output busses. The particular register from which the data comes is determined by the state of the Select Input. A less obvious use is as a function generator. The LS157 can generate any four of the 16 different functions of two variables with one variable common. This is useful for implementing highly irregular logic.

TRUTH TABLE
ENABLE E H L L L L
H = HIGH Voltage Level L = LOW Voltage Level X = Dont Care

SELECT INPUT S X H H L L I0 X X X L H

INPUTS I1 X L H X X

OUTPUT Z L L H L H

http://onsemi.com
116

SN74LS157
DC CHARACTERISTICS OVER OPERATING TEMPERATURE RANGE (unless otherwise specified)
Limits Symbol VIH VIL VIK VOH Parameter Input HIGH Voltage Input LOW Voltage Input Clamp Diode Voltage Output HIGH Voltage 2.7 0.65 3.5 0.25 VO OL Output LOW Voltage 0.35 Input HIGH Current I0, I1 E, S I0, I1 E, S IIL IOS ICC Input LOW Current I0, I1 E, S Short Circuit Current (Note 1) Power Supply Current 20 0.5 20 40 0.1 0.2 0.4 0.8 100 16 V A IOL = 8.0 mA 0.4 Min 2.0 0.8 1.5 Typ Max Unit V V V V V Test Conditions Guaranteed Input HIGH Voltage for All Inputs Guaranteed Input LOW Voltage for All Inputs VCC = MIN, IIN = 18 mA VCC = MIN, IOH = MAX, VIN = VIH or VIL per Truth Table IOL = 4.0 mA VCC = VCC MIN, VIN = VIL or VIH per Truth Table

VCC = MAX, VIN = 2.7 V

IIH

mA

VCC = MAX, VIN = 7.0 V

mA mA mA

VCC = MAX, VIN = 0.4 V VCC = MAX VCC = MAX

Note 1: Not more than one output should be shorted at a time, nor for more than 1 second.

AC CHARACTERISTICS (TA = 25C)

Limits Symbol tPLH tPHL tPLH tPHL tPLH tPHL Parameter Propagation Delay Data to Output Propagation Delay Enable to Output Propagation Delay Select to Output Min Typ 9.0 9.0 13 14 15 18 Max 14 14 20 21 23 27 Unit ns ns ns Figure 2 Figure 1 Figure 2 VCC = 5.0 V CL = 15 pF Test Conditions

AC WAVEFORMS

VIN

1.3 V tPHL

1.3 V tPLH 1.3 V

VIN

1.3 V tPHL

1.3 V tPLH 1.3 V

VOUT

1.3 V

VOUT

1.3 V

Figure 1.

Figure 2.

http://onsemi.com
117

SN74LS161A SN74LS163A BCD Decade Counters/ 4-Bit Binary Counters

The LS161A / 163A are high-speed 4-bit synchronous counters. They are edge-triggered, synchronously presettable, and cascadable MSI building blocks for counting, memory addressing, frequency division and other applications. The LS161A and LS163A count modulo 16 (binary). The LS161A has an asynchronous Master Reset (Clear) input that overrides, and is independent of, the clock and all other control inputs. The LS163A has a Synchronous Reset (Clear) input that overrides all other control inputs, but is active only during the rising clock edge.
Binary (Modulo 16) Asynchronous Reset Synchronous Reset LS161A LS163A

http://onsemi.com

LOW POWER SCHOTTKY

Synchronous Counting and Loading Two Count Enable Inputs for High Speed Synchronous Expansion Terminal Count Fully Decoded Edge-Triggered Operation Typical Count Rate of 35 MHz ESD > 3500 Volts

16 1

PLASTIC N SUFFIX CASE 648

GUARANTEED OPERATING RANGES

Symbol VCC TA IOH IOL Parameter Supply Voltage Operating Ambient Temperature Range Output Current High Output Current Low Min 4.75 0 Typ 5.0 25 Max 5.25 70 0.4 8.0 Unit V C mA mA
16 1

SOIC D SUFFIX CASE 751B

ORDERING INFORMATION
Device SN74LS161AN SN74LS161AD SN74LS163AN SN74LS163AD Package 16 Pin DIP 16 Pin 16 Pin DIP 16 Pin Shipping 2000 Units/Box 2500/Tape & Reel 2000 Units/Box 2500/Tape & Reel

Semiconductor Components Industries, LLC, 1999

118

December, 1999 Rev. 0

Publication Order Number: SN74LS161A/D

SN74LS161A SN74LS163A
CONNECTION DIAGRAM DIP (TOP VIEW)
VCC 16 TC 15 Q0 14 Q1 13 Q2 12 Q3 11 CET 10 PE 9 NOTE: The Flatpak version has the same pinouts (Connection Diagram) as the Dual In-Line Package. *MR for LS161A *SR for LS163A 1 *R 2 CP 3 P0 4 P1 5 P2 6 P3 8 7 CEP GND

LOADING (Note a) PIN NAMES PE P0 P3 CEP CET CP MR SR Q0 Q3 TC Parallel Enable (Active LOW) Input Parallel Inputs Count Enable Parallel Input Count Enable Trickle Input Clock (Active HIGH Going Edge) Input Master Reset (Active LOW) Input Synchronous Reset (Active LOW) Input Parallel Outputs Terminal Count Output HIGH 1.0 U.L. 0.5 U.L. 0.5 U.L. 1.0 U.L. 0.5 U.L. 0.5 U.L. 1.0 U.L. 10 U.L. 10 U.L. LOW 0.5 U.L. 0.25 U.L. 0.25 U.L. 0.5 U.L. 0.25 U.L. 0.25 U.L. 0.5 U.L. 5 U.L. 5 U.L.

NOTES: a) 1 TTL Unit Load (U.L.) = 40 mA HIGH/1.6 mA LOW.

LOGIC SYMBOL
9 3 4 5 6

7 10 2

PE P0 P1 P2 P3 CEP CET CP TC 15

*R Q0 Q1 Q2 Q3

1 14 13 12 11 VCC = PIN 16 GND = PIN 8 *MR for LS161A *SR for LS163A

http://onsemi.com
119

SN74LS161A SN74LS163A
STATE DIAGRAM
LS161A LS163A 0 1 2 3 LOGIC EQUATIONS 4 Count Enable = CEP CET PE TC for LS161A & LS163A = CET Q0 Q1 Q2 Q3 Preset = PE CP + (rising clock edge) Reset = MR (LS161A) Reset = SR CP + (rising clock edge) Reset = (LS163A)

15

14

13

12

11

10

FUNCTIONAL DESCRIPTION

The LS161A / 163A are 4-bit synchronous counters with a synchronous Parallel Enable (Load) feature. The counters consist of four edge-triggered D flip-flops with the appropriate data routing networks feeding the D inputs. All changes of the Q outputs (except due to the asynchronous Master Reset in the LS161A) occur as a result of, and synchronous with, the LOW to HIGH transition of the Clock input (CP). As long as the set-up time requirements are met, there are no special timing or activity constraints on any of the mode control or data inputs. Three control inputs Parallel Enable (PE), Count Enable Parallel (CEP) and Count Enable Trickle (CET) select the mode of operation as shown in the tables below. The Count Mode is enabled when the CEP, CET, and PE inputs are HIGH. When the PE is LOW, the counters will synchronously load the data from the parallel inputs into the flip-flops on the LOW to HIGH transition of the clock. Either the CEP or CET can be used to inhibit the count sequence. With the PE held HIGH, a LOW on either the CEP or CET inputs at least one set-up time prior to the LOW to HIGH clock transition will cause the existing output states to be retained. The AND feature of the two Count Enable inputs (CET CEP) allows synchronous cascading without external gating and without delay accumulation over any practical number of bits or digits.

The Terminal Count (TC) output is HIGH when the Count Enable Trickle (CET) input is HIGH while the counter is in its maximum count state (HLLH for the BCD counters, HHHH for the Binary counters). Note that TC is fully decoded and will, therefore, be HIGH only for one count state. The LS161A and LS163A count modulo 16 following a binary sequence. They generate a TC when the CET input is HIGH while the counter is in state 15 (HHHH). From this state they increment to state 0 (LLLL). The Master Reset (MR) of the LS161A is asynchronous. When the MR is LOW, it overrides all other input conditions and sets the outputs LOW. The MR pin should never be left open. If not used, the MR pin should be tied through a resistor to VCC, or to a gate output which is permanently set to a HIGH logic level. The active LOW Synchronous Reset (SR) input of the LS163A acts as an edge-triggered control input, overriding CET, CEP and PE, and resetting the four counter flip-flops on the LOW to HIGH transition of the clock. This simplifies the design from race-free logic controlled reset circuits, e.g., to reset the counter synchronously after reaching a predetermined value.

MODE SELECT TABLE

*SR L H H H H PE X L H H H CET X X H L X CEP X X H X L Action on the Rising Clock Edge ( RESET (Clear) LOAD (Pn Qn ) COUNT (Increment) NO CHANGE (Hold) NO CHANGE (Hold) )

*For the LS163A only. H = HIGH Voltage Level L = LOW Voltage Level X = Dont Care

http://onsemi.com
120

SN74LS161A SN74LS163A
LS161A DC CHARACTERISTICS OVER OPERATING TEMPERATURE RANGE (unless otherwise specified)
Limits Symbol VIH VIL VIK VOH Parameter Input HIGH Voltage Input LOW Voltage Input Clamp Diode Voltage Output HIGH Voltage 2.7 0.65 3.5 0.25 VO OL Output LOW Voltage 0.35 Input HIGH Current MR, Data, CEP, Clock PE, CET MR, Data, CEP, Clock PE, CET IIL IOS ICC Input LOW Current MR, Data, CEP, Clock PE, CET Short Circuit Current (Note 1) Power Supply Current Total, Output HIGH Total, Output LOW 20 0.5 20 40 0.1 0.2 0.4 0.8 100 31 32 V A mA IOL = 8.0 mA 0.4 Min 2.0 0.8 1.5 Typ Max Unit V V V V V Test Conditions Guaranteed Input HIGH Voltage for All Inputs Guaranteed Input LOW Voltage for All Inputs VCC = MIN, IIN = 18 mA VCC = MIN, IOH = MAX, VIN = VIH or VIL per Truth Table IOL = 4.0 mA VCC = VCC MIN, VIN = VIL or VIH per Truth Table

VCC = MAX, VIN = 2.7 V VCC = MAX, VIN = 7.0 V

IIH

mA mA mA

VCC = MAX, VIN = 0.4 V VCC = MAX VCC = MAX

Note 1: Not more than one output should be shorted at a time, nor for more than 1 second.

LS163A DC CHARACTERISTICS OVER OPERATING TEMPERATURE RANGE (unless otherwise specified)

Limits Symbol VIH VIL VIK VOH Parameter Input HIGH Voltage Input LOW Voltage Input Clamp Diode Voltage Output HIGH Voltage 2.7 0.65 3.5 0.25 VO OL Output LOW Voltage 0.35 Input HIGH Current Data, CEP, Clock PE, CET, SR Data, CEP, Clock PE, CET, SR IIL IOS ICC Input LOW Current Data, CEP, Clock, PE, SR CET Short Circuit Current (Note 1) Power Supply Current Total, Output HIGH Total, Output LOW 20 0.5 20 40 0.1 0.2 0.4 0.8 100 31 32 V A mA IOL = 8.0 mA 0.4 Min 2.0 0.8 1.5 Typ Max Unit V V V V V Test Conditions Guaranteed Input HIGH Voltage for All Inputs Guaranteed Input LOW Voltage for All Inputs VCC = MIN, IIN = 18 mA VCC = MIN, IOH = MAX, VIN = VIH or VIL per Truth Table IOL = 4.0 mA VCC = VCC MIN, VIN = VIL or VIH per Truth Table

VCC = MAX, VIN = 2.7 V VCC = MAX, VIN = 7.0 V

IIH

mA mA mA

VCC = MAX, VIN = 0.4 V VCC = MAX VCC = MAX

Note 1: Not more than one output should be shorted at a time, nor for more than 1 second.

http://onsemi.com
121

SN74LS161A SN74LS163A
AC CHARACTERISTICS (TA = 25C)
Limits Symbol fMAX tPLH tPHL tPLH tPHL tPLH tPHL tPHL Parameter Maximum Clock Frequency Propagation Delay Clock to TC Propagation Delay Clock to Q Propagation Delay CET to TC MR or SR to Q Min 25 Typ 32 20 18 13 18 9.0 9.0 20 35 35 24 27 14 14 28 Max Unit MHz ns ns ns ns VCC = 5.0 V CL = 15 pF Test Conditions

AC SETUP REQUIREMENTS (TA = 25C)

Limits Symbol tWCP tW ts ts th th trec Parameter Clock Pulse Width Low MR or SR Pulse Width Setup Time, other* Setup Time PE or SR Hold Time, data Hold Time, other Recovery Time MR to CP Min 25 20 20 25 3 0 15 Typ Max Unit ns ns ns ns ns ns ns VCC = 5.0 V Test Conditions

*CEP, CET, or DATA

DEFINITION OF TERMS

SETUP TIME (ts) is defined as the minimum time required for the correct logic level to be present at the logic input prior to the clock transition from LOW to HIGH in order to be recognized and transferred to the outputs. HOLD TIME (th) is defined as the minimum time following the clock transition from LOW to HIGH that the logic level must be maintained at the input in order to ensure

continued recognition. A negative HOLD TIME indicates that the correct logic level may be released prior to the clock transition from LOW to HIGH and still be recognized. RECOVERY TIME (trec) is defined as the minimum time required between the end of the reset pulse and the clock transition from LOW to HIGH in order to recognize and transfer HIGH Data to the Q outputs.

AC WAVEFORMS

tW(H) CP 1.3 V tPHL Q 1.3 V

tW(L) 1.3 V tPLH 1.3 V OTHER CONDITIONS: PE = MR (SR) = H CEP = CET = H

MR

1.3 V

tW trec 1.3 V OTHER CONDITIONS: PE = L P0 = P1 = P2 = P3 = H

CP Q0 Q1 Q2 Q3

tPHL 1.3 V

Figure 1. Clock to Output Delays, Count Frequency, and Clock Pulse Width

Figure 2. Master Reset to Output Delay, Master Reset Pulse Width, and Master Reset Recovery Time

http://onsemi.com
122

SN74LS161A SN74LS163A
AC WAVEFORMS (continued) COUNT ENABLE TRICKLE INPUT TO TERMINAL COUNT OUTPUT DELAYS
The positive TC pulse occurs when the outputs are in the (Q0 Q1 Q2 Q3) state for the LS161 and LS163. TC

CET

1.3 V tPLH 1.3 V

1.3 V tPHL 1.3 V

Figure 3.

OTHER CONDITIONS: CP = PE = CEP = MR = H

CLOCK TO TERMINAL COUNT DELAYS

CP The positive TC pulse is coincident with the output state (Q0 Q1 Q2 Q3) for the LS161 and LS163. TC

1.3 V tPLH 1.3 V

1.3 V

1.3 V tPHL 1.3 V

Figure 4.

OTHER CONDITIONS: PE = CEP = CET = MR = H

CP

1.3 V th(H) = 0 1.3 V ts(L) 1.3 V

1.3 V th(L) = 0 1.3 V

SETUP TIME (ts) AND HOLD TIME (th) FOR PARALLEL DATA INPUTS
The shaded areas indicate when the input is permitted to change for predictable output performance. P0 P1 P2 P3

ts(H)

Q0 Q1 Q2 Q3

Figure 5.

OTHER CONDITIONS: PE = L, MR = H

SETUP TIME (ts) AND HOLD TIME (th) FOR COUNT ENABLE (CEP) AND (CET) AND PARALLEL ENABLE (PE) INPUTS
The shaded areas indicate when the input is permitted to change for predictable output performance. 1.3 V th (L) = 0 1.3 V PARALLEL LOAD (See Fig. 5) Q RESPONSE TO PE RESET Q RESPONSE TO SR COUNT OR LOAD Q OTHER CONDITIONS: PE = H, MR = H ts(H) 1.3 V CP th(H) = 0 1.3 V COUNT MODE (See Fig. 7) CEP ts(H) CET 1.3 V ts(H)

CP ts(L) SR or PE

1.3 V th(H) = 0 1.3 V th(H) = 0 1.3 V COUNT ts(L)

1.3 V th(L) = 0 1.3 V ts(L) 1.3 V HOLD

1.3 V

th(L) = 0 1.3 V HOLD

Figure 6.

Figure 7.

http://onsemi.com
123

SN74LS164 Serial-In Parallel-Out Shift Register

The SN74LS164 is a high speed 8-Bit Serial-In Parallel-Out Shift Register. Serial data is entered through a 2-Input AND gate synchronous with the LOW to HIGH transition of the clock. The device features an asynchronous Master Reset which clears the register setting all outputs LOW independent of the clock. It utilizes the Schottky diode clamped process to achieve high speeds and is fully compatible with all ON Semiconductor TTL products.
http://onsemi.com

Typical Shift Frequency of 35 MHz Asynchronous Master Reset Gated Serial Data Input Fully Synchronous Data Transfers Input Clamp Diodes Limit High Speed Termination Effects ESD > 3500 Volts
14

LOW POWER SCHOTTKY

GUARANTEED OPERATING RANGES

Symbol VCC TA IOH IOL Parameter Supply Voltage Operating Ambient Temperature Range Output Current High Output Current Low Min 4.75 0 Typ 5.0 25 Max 5.25 70 0.4 8.0 Unit V C mA mA

PLASTIC N SUFFIX CASE 646

14 1

SOIC D SUFFIX CASE 751A

ORDERING INFORMATION
Device SN74LS164N SN74LS164D Package 14 Pin DIP 14 Pin Shipping 2000 Units/Box 2500/Tape & Reel

Semiconductor Components Industries, LLC, 1999

124

December, 1999 Rev. 6

Publication Order Number: SN74LS164/D

SN74LS164
CONNECTION DIAGRAM DIP (TOP VIEW)
VCC 14 Q7 13 Q6 12 Q5 11 Q4 10 MR 9 CP 8 NOTE: The Flatpak version has the same pinouts (Connection Diagram) as the Dual In-Line Package. 1 A 2 B 3 Q0 4 Q1 5 Q2 6 Q3 7 GND

LOADING (Note a) PIN NAMES A, B CP MR Q0 Q7 Data Inputs Clock (Active HIGH Going Edge) Input Master Reset (Active LOW) Input Outputs HIGH 0.5 U.L. 0.5 U.L. 0.5 U.L. 10 U.L. LOW 0.25 U.L. 0.25 U.L. 0.25 U.L. 5 U.L.

NOTES: a) 1 TTL Unit Load (U.L.) = 40 mA HIGH/1.6 mA LOW.

LOGIC SYMBOL

1 2 8

A LS164 B 8-BIT SHIFT REGISTER CP MR Q0 Q1 Q2 Q3 Q4 Q5 Q6 Q7 9 3 4 5 6 10 11 12 13

VCC = PIN 14 GND = PIN 7

http://onsemi.com
125

SN74LS164
LOGIC DIAGRAM
1 2

A D B CD CD CD CD CD CD CD CD CP MR VCC = PIN 14 GND = PIN 7 = PIN NUMBERS Q0

3

Q1
4

Q2
5

Q3
6

Q4
10

Q5
11

Q6
12

Q7
13

FUNCTIONAL DESCRIPTION

The LS164 is an edge-triggered 8-bit shift register with serial data entry and an output from each of the eight stages. Data is entered serially through one of two inputs (A or B); either of these inputs can be used as an active HIGH Enable for data entry through the other input. An unused input must be tied HIGH, or both inputs connected together.

Each LOW-to-HIGH transition on the Clock (CP) input shifts data one place to the right and enters into Q0 the logical AND of the two data inputs (AB) that existed before the rising clock edge. A LOW level on the Master Reset (MR) input overrides all other inputs and clears the register asynchronously, forcing all Q outputs LOW.

MODE SELECT TRUTH TABLE

OPERATING MODE Reset (Clear) Shift INPUTS MR L H H H H A X I I h h B X I h I h OUTPUTS Q0 L L L L H Q1Q7 LL q0 q6 q0 q6 q0 q6 q0 q6

L (l) = LOW Voltage Levels H (h) = HIGH Voltage Levels X = Dont Care qn = Lower case letters indicate the state of the referenced input or output one qn = set-up time prior to the LOW to HIGH clock transition.

http://onsemi.com
126

SN74LS164
DC CHARACTERISTICS OVER OPERATING TEMPERATURE RANGE (unless otherwise specified)
Limits Symbol VIH VIL VIK VOH Parameter Input HIGH Voltage Input LOW Voltage Input Clamp Diode Voltage Output HIGH Voltage 2.7 0.65 3.5 0.25 VO OL Output LOW Voltage 0.35 IIH IIL IOS ICC Input HIGH Current 0.1 Input LOW Current Short Circuit Current (Note 1) Power Supply Current 20 0.4 100 27 0.5 20 V A mA mA mA mA IOL = 8.0 mA 0.4 Min 2.0 0.8 1.5 Typ Max Unit V V V V V Test Conditions Guaranteed Input HIGH Voltage for All Inputs Guaranteed Input LOW Voltage for All Inputs VCC = MIN, IIN = 18 mA VCC = MIN, IOH = MAX, VIN = VIH or VIL per Truth Table IOL = 4.0 mA VCC = VCC MIN, VIN = VIH or VIL per Truth Table

VCC = MAX, VIN = 2.7 V VCC = MAX, VIN = 7.0 V VCC = MAX, VIN = 0.4 V VCC = MAX VCC = MAX

Note 1: Not more than one output should be shorted at a time, nor for more than 1 second.

AC CHARACTERISTICS (TA = 25C)

Limits Symbol fMAX tPHL tPLH tPHL Parameter Maximum Clock Frequency Propagation Delay MR to Output Q Propagation Delay Clock to Output Q Min 25 Typ 36 24 17 21 36 27 32 Max Unit MHz ns ns VCC = 5.0 V CL = 15 pF F Test Conditions

AC SETUP REQUIREMENTS (TA = 25C)

Limits Symbol tW ts th trec Parameter CP, MR Pulse Width Data Setup Time Data Hold Time MR to Clock Recovery Time Min 20 15 5.0 20 Typ Max Unit ns ns ns ns VCC = 5 0 V 5.0 Test Conditions

http://onsemi.com
127

SN74LS164
AC WAVEFORMS
*The shaded areas indicate when the input is permitted to change for predictable output performance.

I/f max

MR 1.3 V

1.3 V CP

tW 1.3 V tPHL

1.3 V tW

1.3 V trec 1.3 V

tPLH 1.3 V CP tPHL

1.3 V CONDITIONS: MR = H

1.3 V

Figure 1. Clock to Output Delays and Clock Pulse Width

Figure 2. Master Reset Pulse Width, Master Reset to Output Delay and Master Reset to Clock Recovery Time

1/fmax tW CP 1.3 V ts(H) D * 1.3 V 1.3 V 1.3 V ts(L) 1.3 V 1.3 V

th(H) 1.3 V

th(L) 1.3 V

1.3 V

1.3 V

Figure 3. Data Setup and Hold Times

http://onsemi.com
128

SN74LS165 8-Bit Parallel-to-Serial Shift Register

The SN74LS165 is an 8-bit parallel load or serial-in register with complementary outputs available from the last stage. Parallel inputing occurs asynchronously when the Parallel Load (PL) input is LOW. With PL HIGH, serial shifting occurs on the rising edge of the clock; new data enters via the Serial Data (DS) input. The 2-input OR clock can be used to combine two independent clock sources, or one input can act as an active LOW clock enable.
GUARANTEED OPERATING RANGES
Symbol VCC TA IOH IOL Parameter Supply Voltage Operating Ambient Temperature Range Output Current High Output Current Low Min 4.75 0 Typ 5.0 25 Max 5.25 70 0.4 8.0 Unit V C mA mA
16 1

http://onsemi.com

LOW POWER SCHOTTKY

PLASTIC N SUFFIX CASE 648

16 1

SOIC D SUFFIX CASE 751B

ORDERING INFORMATION
Device SN74LS165N SN74LS165D Package 16 Pin DIP 16 Pin Shipping 2000 Units/Box 2500/Tape & Reel

Semiconductor Components Industries, LLC, 1999

129

December, 1999 Rev. 6

Publication Order Number: SN74LS165/D

SN74LS165
CONNECTION DIAGRAM DIP (TOP VIEW)
VCC 16 CP2 15 P3 14 P2 13 P1 12 P0 11 DS 10 Q7 9 NOTE: The Flatpak version has the same pinouts (Connection Diagram) as the Dual In-Line Package. 1 PL 2 CP1 3 P4 4 P5 5 P6 6 P7 7 Q7 8 GND

LOADING (Note a) PIN NAMES CP1, CP2 DS PL P0 P7 Q7 Q7 Clock (LOWtoHIGH Going Edge) Inputs Serial Data Input Asynchronous Parallel Load (Active LOW) Input Parallel Data Inputs Serial Output from Last State Complementary Output HIGH 0.5 U.L. 0.5 U.L. 1.5 U.L. 0.5 U.L. 10 U.L. 10 U.L. LOW 0.25 U.L. 0.25 U.L. 0.75 U.L. 0.25 U.L. 5 U.L. 5 U.L.

NOTES: a) 1 TTL Unit Load (U.L.) = 40 mA HIGH/1.6 mA LOW.

LOGIC SYMBOL

1 11 12 13 14 3 4 5 6 PL P0 P1 P2 P3 P4 P5 P6 P7 DS Q7 CP Q7

10 2 15

9 7

VCC = PIN 16 GND = PIN 8

http://onsemi.com
130

SN74LS165
LOGIC DIAGRAM
11 12 13 14 3 4 5 6

P0

P1

P2

P3

P4

P5

P6

P7

10 DS 2 CP1 15 CP2 1 PL

PRESET Q0 S CP R CLQ0

PRESET Q1 S CP R CL Q1

PRESET S Q2 CP R CLQ2

PRESET S Q3 CP R CLQ3

PRESET Q4 S CP R CLQ4

PRESET S Q5 CP R CLQ5

PRESET S Q6 CP R CLQ6

PRESET Q7 S CP R CL Q7

VCC = PIN 16 GND = PIN 8 = PIN NUMBERS

FUNCTIONAL DESCRIPTION

The SN74LS165 contains eight clocked master/slave RS flip-flops connected as a shift register, with auxiliary gating to provide overriding asynchronous parallel entry. Parallel data enters when the PL signal is LOW. The parallel data can change while PL is LOW, provided that the recommended setup and hold times are observed. For clock operation, PL must be HIGH. The two clock inputs perform identically; one can be used as a clock inhibit

by applying a HIGH signal. To avoid double clocking, however, the inhibit signal should only go HIGH while the clock is HIGH. Otherwise, the rising inhibit signal will cause the same response as a rising clock edge. The flip-flops are edge-triggered for serial operations. The serial input data can change at any time, provided only that the recommended setup and hold times are observed, with respect to the rising edge of the clock.

TRUTH TABLE
CP PL 1 L H H H H X L H 2 X Q0 P0 DS Q0 DS Q0 Q1 P1 Q0 Q1 Q0 Q1 Q2 P2 Q1 Q2 Q1 Q2 Q3 P3 Q2 Q3 Q2 Q3 Q4 P4 Q3 Q4 Q3 Q4 Q5 P5 Q4 Q5 Q4 Q5 Q6 P6 Q5 Q6 Q5 Q6 Q7 P7 Q6 Q7 Q6 Q7 Parallel Entry Right Shift No Change Right Shift No Change CONTENTS RESPONSE

L H

H = HIGH Voltage Level L = LOW Voltage Level X = Immaterial

http://onsemi.com
131

SN74LS165
DC CHARACTERISTICS OVER OPERATING TEMPERATURE RANGE (unless otherwise specified)
Limits Symbol VIH VIL VIK VOH Parameter Input HIGH Voltage Input LOW Voltage Input Clamp Diode Voltage Output HIGH Voltage 2.7 0.65 3.5 0.25 VO OL Output LOW Voltage 0.35 Input HIGH Current Other Inputs PL Input Other Inputs PL Input IIL IOS ICC Input LOW Current Other Inputs PL Input Short Circuit Current (Note 1) Power Supply Current 20 0.5 20 60 0.1 0.3 0.4 1.2 100 36 V A IOL = 8.0 mA 0.4 Min 2.0 0.8 1.5 Typ Max Unit V V V V V Test Conditions Guaranteed Input HIGH Voltage for All Inputs Guaranteed Input LOW Voltage for All Inputs VCC = MIN, IIN = 18 mA VCC = MIN, IOH = MAX, VIN = VIH or VIL per Truth Table IOL = 4.0 mA VCC = VCC MIN, VIN = VIL or VIH per Truth Table

VCC = MAX, VIN = 2.7 V

IIH

mA

VCC = MAX, VIN = 7.0 V

mA mA mA

VCC = MAX, VIN = 0.4 V VCC = MAX VCC = MAX

Note 1: Not more than one output should be shorted at a time, nor for more than 1 second.

AC CHARACTERISTICS (TA = 25C)

Limits Symbol fMAX tPLH tPHL tPLH tPHL tPLH tPHL tPLH tPHL Parameter Maximum Input Clock Frequency Propagation Delay PL to Output Propagation Delay Clock to Output Propagation Delay P7 to Q7 Propagation Delay P7 to Q7 Min 25 Typ 35 22 22 27 28 14 21 21 16 35 35 40 40 25 30 30 25 Max Unit MHz ns ns ns ns VCC = 5.0 V CL = 15 pF F Test Conditions

AC SETUP REQUIREMENTS (TA = 25C)

Limits Symbol tW tW ts ts ts th trec 1 The Parameter CP Clock Pulse Width PL Pulse Width Parallel Data Setup Time Serial Data Setup Time CP1 to CP2 Setup Time1 Hold Time Recovery Time, PL to CP Min 25 15 10 20 30 0 45 Typ Max Unit ns ns ns ns ns ns ns VCC = 5.0 V Test Conditions

role of CP1 and CP2 in an application may be interchanged.

http://onsemi.com
132

SN74LS165
DEFINITION OF TERMS:

SETUP TIME (ts) is defined as the minimum time required for the correct logic level to be present at the logic input prior to the clock transition from LOW-to-HIGH in order to be recognized and transferred to the outputs. HOLD TIME (th) is defined as the minimum time following the clock transition from LOW-to-HIGH that the logic level must be maintained at the input in order to ensure

continued recognition. A negative hold time indicates that the correct logic level may be released prior to the clock transition from LOW-to-HIGH and still be recognized. RECOVERY TIME (trec) is defined as the minimum time required between the end of the PL pulse and the clock transition from LOW-to-HIGH in order to recognize and transfer loaded Data to the Q outputs.

AC WAVEFORMS

CP1 tW ts CP2 1.3 V tPHL Q7 OR Q7 1.3 V 1/fmax tW tPLH 1.3 V 1.3 V Q7 OR Q7 PL 1.3 V tPLH 1.3 V 1.3 V 1.3 V tPHL 1.3 V

Figure 1.

Figure 2.

Pn ts(H) PL OR CP

1.3 V th(H) 1.3 V ts(L)

1.3 V th(L) 1.3 V

PL

1.3 V tW

1.3 V trec 1.3 V

CP

Figure 3.

Figure 4.

http://onsemi.com
133

SN74LS166 8-Bit Shift Registers

The SN74LS166 is an 8-Bit Shift Register. Designed with all inputs buffered, the drive requirements are lowered to one 74LS standard load. By utilizing input clamping diodes, switching transients are minimized and system design simplified. The LS166 is a parallel-in or serial-in, serial-out shift register and has a complexity of 77 equivalent gates with gated clock inputs and an overriding clear input. The shift/load input establishes the parallel-in or serial-in mode. When high, this input enables the serial data input and couples the eight flip-flops for serial shifting with each clock pulse. Synchronous loading occurs on the next clock pulse when this is low and the parallel data inputs are enabled. Serial data flow is inhibited during parallel loading. Clocking is done on the low-to-high level edge of the clock pulse via a two input positive NOR gate, which permits one input to be used as a clock enable or clock inhibit function. Clocking is inhibited when either of the clock inputs are held high, holding either input low enables the other clock input. This will allow the system clock to be free running and the register stopped on command with the other clock input. A change from low-to-high on the clock inhibit input should only be done when the clock input is high. A buffered direct clear input overrides all other inputs, including the clock, and sets all flip-flops to zero.

http://onsemi.com

LOW POWER SCHOTTKY

16 1

Synchronous Load Direct Overriding Clear Parallel to Serial Conversion

GUARANTEED OPERATING RANGES
Symbol VCC TA IOH IOL Parameter Supply Voltage Operating Ambient Temperature Range Output Current High Output Current Low Min 4.75 0 Typ 5.0 25 Max 5.25 70 0.4 8.0 Unit V C mA mA
16

PLASTIC N SUFFIX CASE 648

SOIC D SUFFIX CASE 751B

ORDERING INFORMATION
Device SN74LS166N SN74LS166D Package 16 Pin DIP 16 Pin Shipping 2000 Units/Box 2500/Tape & Reel

Semiconductor Components Industries, LLC, 1999

134

December, 1999 Rev. 6

Publication Order Number: SN74LS166/D

SN74LS166
PARALLEL PARALLEL INPUTS F 11 F E 10 E CLEAR 9

SHIFT/ INPUT OUTPUT G H QH VCC LOAD 16 15 SHIFT/ LOAD 14 H 13 QH 12 G

SERIAL INPUT A 1 SERIAL INPUT 2 A B 3 B C 4 C D 5 D

CLEAR CLOCK INHIBIT CK 8 6 7 CLOCK CLOCK GND INHIBIT

PARALLEL INPUTS

FUNCTION TABLE
INPUTS CLEAR L H H H H H SHIFT/ LOAD X X L H H X CLOCK INHIBIT X L L L L H PARALLEL CLOCK X L SERIAL A...H X X X H L X X X a...h X X X QA L QA0 a H L QA0 QB L QB0 b QAn QAn QB0 L QH0 h QGn QGn QH0 INTERNAL OUTPUTS OUTPUT QH

http://onsemi.com
135

SN74LS166
Typical Clear, Shift, Load, Inhibit, and Shift Sequences
CLOCK CLOCK INIHIBIT CLEAR SERIAL INPUT SHIFT/LOAD A B C PARALLEL INPUTS D E F G H OUTPUT QH SERIAL SHIFT CLEAR (9) CLEAR (1) SERIAL INPUT (15) SHIFT/LOAD (2) A
R CK S

H L H L H L H H INHIBIT LOAD H H L H L H L SERIAL SHIFT H

QA B (3)
R S

CK

QB C (4)
R S

CK

QC D (5)
R S

CK

QD E (10)
R S

CK

(11)
R

QE

CK

QF (12) G
R CK S

QG H CLOCK CLOCK INHIBIT (14) (7) (6)

R S

CK

(13) Q H

http://onsemi.com
136

SN74LS166
DC CHARACTERISTICS OVER OPERATING TEMPERATURE RANGE (unless otherwise specified)
Limits Symbol VIH VIL VIK VOH Parameter Input HIGH Voltage Input LOW Voltage Input Clamp Diode Voltage Output HIGH Voltage 2.7 0.65 3.5 0.25 VO OL Output LOW Voltage 0.35 IIH IIL IOS ICC Input HIGH Current 0.1 Input LOW Current Short Circuit Current (Note 1) Power Supply Current 20 0.4 100 38 0.5 20 V A mA mA mA mA IOL = 8.0 mA 0.4 Min 2.0 0.8 1.5 Typ Max Unit V V V V V Test Conditions Guaranteed Input HIGH Voltage for All Inputs Guaranteed Input LOW Voltage for All Inputs VCC = MIN, IIN = 18 mA VCC = MIN, IOH = MAX, VIN = VIH or VIL per Truth Table IOL = 4.0 mA VCC = VCC MIN, VIN = VIL or VIH per Truth Table

VCC = MAX, VIN = 2.7 V VCC = MAX, VIN = 7.0 V VCC = MAX, VIN = 0.4 V VCC = MAX VCC = MAX

Note 1: Not more than one output should be shorted at a time, nor for more than 1 second.

http://onsemi.com
137

SN74LS166
TEST TABLE FOR SYNCHRONOUS INPUTS
DATA INPUT FOR TEST H Serial Input SHIFT/LOAD 0V 4.5 V OUTPUT TESTED QH at tn+1 QH at tn+8

AC WAVEFORMS
tw(clear) CLEAR INPUT Vref Vref 0V tn CLOCK INPUT Vref tw(clock) DATA INPUT (SEE TEST TABLE) Vref Vref tsu tn + 1 (SEE NOTE 1) tn tn + 1 3V Vref th Vref tsu Vref th Vref 0V tPHL (clear-Q) Vref tPHL (CLK-Q) VOH Vref
NOTE 1. tn = bit time before clocking transition NOTE 1. tn+1 = bit time after one clocking transition NOTE 1. tn+8 = bit time after eight clocking transition NOTE 1. LS166 Vref = 1.3 V.

3V

0V 3V

tPLH (CLK-Q)

OUTPUT Q

Vref VOL

AC CHARACTERISTICS (TA = 25C)

Limits Symbol fMAX tPHL tPLH tPHL Parameter Maximum Clock Frequency Clear to Output Clock to Output Min 25 Typ 35 19 23 24 30 35 35 Max Unit MHz ns ns VCC = 5.0 V CL = 15 pF F Test Conditions

AC SETUP REQUIREMENTS (TA = 25C)

Limits Symbol tW ts ts th Parameter Clock Clear Pulse Width Mode Control Setup Time Data Setup Time Hold Time, Any Input Min 30 30 20 15 Typ Max Unit ns ns ns ns VCC = 5 0 V 5.0 Test Conditions

http://onsemi.com
138

SN74LS174 Hex D Flip-Flop

The LSTTL / MSI SN74LS174 is a high speed Hex D Flip-Flop. The device is used primarily as a 6-bit edge-triggered storage register. The information on the D inputs is transferred to storage during the LOW to HIGH clock transition. The device has a Master Reset to simultaneously clear all flip-flops. The LS174 is fabricated with the Schottky barrier diode process for high speed and is completely compatible with all ON Semiconductor TTL families.

http://onsemi.com

Edge-Triggered D-Type Inputs Buffered-Positive Edge-Triggered Clock Asynchronous Common Reset Input Clamp Diodes Limit High Speed Termination Effects

LOW POWER SCHOTTKY

GUARANTEED OPERATING RANGES

Symbol VCC TA IOH IOL Parameter Supply Voltage Operating Ambient Temperature Range Output Current High Output Current Low Min 4.75 0 Typ 5.0 25 Max 5.25 70 0.4 8.0 Unit V C mA mA
16 1

PLASTIC N SUFFIX CASE 648

16 1

SOIC D SUFFIX CASE 751B

ORDERING INFORMATION
Device SN74LS174N SN74LS174D Package 16 Pin DIP 16 Pin Shipping 2000 Units/Box 2500/Tape & Reel

Semiconductor Components Industries, LLC, 1999

139

December, 1999 Rev. 6

Publication Order Number: SN74LS174/D

SN74LS174
CONNECTION DIAGRAM DIP (TOP VIEW)
VCC 16 Q5 15 D5 14 D4 13 Q4 12 D3 11 Q3 10 CP 9 NOTE: The Flatpak version has the same pinouts (Connection Diagram) as the Dual In-Line Package. 1 MR 2 Q0 3 D0 4 D1 5 Q1 6 D2 7 Q2 8 GND

LOADING (Note a) PIN NAMES D0 D5 CP MR Q0 Q5 Data Inputs Clock (Active HIGH Going Edge) Input Master Reset (Active LOW) Input Outputs HIGH 0.5 U.L. 0.5 U.L. 0.5 U.L. 10 U.L. LOW 0.25 U.L. 0.25 U.L. 0.25 U.L. 5 U.L.

NOTES: a) 1 TTL Unit Load (U.L.) = 40 mA HIGH/1.6 mA LOW.

LOGIC SYMBOL
3 4 6 11 13 14

9 1

D0 D1 D2 D3 D4 D5 CP MR Q0 Q1 Q2 Q3 Q4 Q5

2 5 7 10 12 15 VCC = PIN 16 GND = PIN 8

LOGIC DIAGRAM
MR CP D5
1 9 14

D4
13

D3
11

D2
6

D1
4

D0
3

D Q CP CD
15

D Q CP CD
12

D Q CP CD
10

D Q CP CD
7

D Q CP CD
5

D Q CP CD
2

Q5

Q4 VCC = PIN 16 GND = PIN 8

Q3

Q2

Q1

Q0

= PIN NUMBERS

http://onsemi.com
140

SN74LS174
FUNCTIONAL DESCRIPTION

The LS174 consists of six edge-triggered D flip-flops with individual D inputs and Q outputs. The Clock (CP) and Master Reset (MR) are common to all flip-flops. Each D inputs state is transferred to the corresponding flip-flops output following the LOW to HIGH Clock (CP) transition.

A LOW input to the Master Reset (MR) will force all outputs LOW independent of Clock or Data inputs. The LS174 is useful for applications where the true output only is required and the Clock and Master Reset are common to all storage elements.

TRUTH TABLE
Inputs (t = n, MR = H) D H L
Note 1: t = n + 1 indicates conditions after next clock.

Outputs (t = n+1) Note 1 Q H L

DC CHARACTERISTICS OVER OPERATING TEMPERATURE RANGE (unless otherwise specified)

Limits Symbol VIH VIL VIK VOH Parameter Input HIGH Voltage Input LOW Voltage Input Clamp Diode Voltage Output HIGH Voltage 2.7 0.65 3.5 0.25 VO OL Output LOW Voltage 0.35 IIH IIL IOS ICC Input HIGH Current 0.1 Input LOW Current Short Circuit Current (Note 1) Power Supply Current 20 0.4 100 26 0.5 20 V A mA mA mA mA IOL = 8.0 mA 0.4 Min 2.0 0.8 1.5 Typ Max Unit V V V V V Test Conditions Guaranteed Input HIGH Voltage for All Inputs Guaranteed Input LOW Voltage for All Inputs VCC = MIN, IIN = 18 mA VCC = MIN, IOH = MAX, VIN = VIH or VIL per Truth Table IOL = 4.0 mA VCC = VCC MIN, VIN = VIL or VIH per Truth Table

VCC = MAX, VIN = 2.7 V VCC = MAX, VIN = 7.0 V VCC = MAX, VIN = 0.4 V VCC = MAX VCC = MAX

Note 1: Not more than one output should be shorted at a time, nor for more than 1 second.

http://onsemi.com
141

SN74LS174
AC CHARACTERISTICS (TA = 25C)
Limits Symbol fMAX tPHL tPLH tPHL Parameter Maximum Input Clock Frequency Propagation Delay, MR to Output Propagation Delay, Clock to Output Min 30 Typ 40 23 20 21 35 30 30 Max Unit MHz ns ns VCC = 5.0 V CL = 15 pF F Test Conditions

AC SETUP REQUIREMENTS (TA = 25C)

Limits Symbol tW ts th trec Parameter Clock or MR Pulse Width Data Setup Time Data Hold Time Recovery Time Min 20 20 5.0 25 Typ Max Unit ns ns ns ns VCC = 5 0 V 5.0 Test Conditions

AC WAVEFORMS
1/fmax tw CP 1.3 V ts(H) D * 1.3 V th(H) ts(L) 1.3 V th(L) 1.3 V tPHL 1.3 V CP Q tPHL 1.3 V 1.3 V MR 1.3 V tW 1.3 V trec 1.3 V

1.3 V tPLH 1.3 V

*The shaded areas indicate when the input is permitted to *change for predictable output performance.

Figure 1. Clock to Output Delays, Clock Pulse Width, Frequency, Setup and Hold Times Data to Clock

Figure 2. Master Reset to Output Delay, Master Reset Pulse Width, and Master Reset Recovery Time

DEFINITIONS OF TERMS

SETUP TIME (ts) is defined as the minimum time required for the correct logic level to be present at the logic input prior to the clock transition from LOW to HIGH in order to be recognized and transferred to the outputs. HOLD TIME (th) is defined as the minimum time following the clock transition from LOW to HIGH that the logic level must be maintained at the input in order to ensure

continued recognition. A negative HOLD TIME indicates that the correct logic level may be released prior to the clock transition from LOW to HIGH and still be recognized. RECOVERY TIME (trec) is defined as the minimum time required between the end of the reset pulse and the clock transition from LOW to HIGH in order to recognize and transfer HIGH Data to the Q outputs.

http://onsemi.com
142

SN74LS175 Quad D Flip-Flop

The LSTTL / MSI SN74LS175 is a high speed Quad D Flip-Flop. The device is useful for general flip-flop requirements where clock and clear inputs are common. The information on the D inputs is stored during the LOW to HIGH clock transition. Both true and complemented outputs of each flip-flop are provided. A Master Reset input resets all flip-flops, independent of the Clock or D inputs, when LOW. The LS175 is fabricated with the Schottky barrier diode process for high speed and is completely compatible with all ON Semiconductor TTL families.

http://onsemi.com

LOW POWER SCHOTTKY

Edge-Triggered D-Type Inputs Buffered-Positive Edge-Triggered Clock Clock to Output Delays of 30 ns Asynchronous Common Reset True and Complement Output Input Clamp Diodes Limit High Speed Termination Effects
16 1

GUARANTEED OPERATING RANGES

Symbol VCC TA IOH IOL Parameter Supply Voltage Operating Ambient Temperature Range Output Current High Output Current Low Min 4.75 0 Typ 5.0 25 Max 5.25 70 0.4 8.0 Unit V C mA mA

PLASTIC N SUFFIX CASE 648

16 1

SOIC D SUFFIX CASE 751B

ORDERING INFORMATION
Device SN74LS175N SN74LS175D Package 16 Pin DIP 16 Pin Shipping 2000 Units/Box 2500/Tape & Reel

Semiconductor Components Industries, LLC, 1999

143

December, 1999 Rev. 6

Publication Order Number: SN74LS175/D

SN74LS175
CONNECTION DIAGRAM DIP (TOP VIEW)
VCC 16 Q3 15 Q3 14 D3 13 D2 12 Q2 11 Q2 10 CP 9 NOTE: The Flatpak version has the same pinouts (Connection Diagram) as the Dual In-Line Package. 1 MR 2 Q0 3 Q0 4 D0 5 D1 6 Q1 7 Q1 8 GND

LOADING (Note a) PIN NAMES D0 D3 CP MR Q0 Q3 Q0 Q3 Data Inputs Clock (Active HIGH Going Edge) Input Master Reset (Active LOW) Input True Outputs Complemented Outputs HIGH 0.5 U.L. 0.5 U.L. 0.5 U.L. 10 U.L. 10 U.L. LOW 0.25 U.L. 0.25 U.L. 0.25 U.L. 5 U.L. 5 U.L.

NOTES: a) 1 TTL Unit Load (U.L.) = 40 mA HIGH/1.6 mA LOW.

LOGIC SYMBOL
4 5 12 13

CP

D0

D1

D2

D3

MR Q0 Q0 Q1 Q1 Q2 Q2 Q3 Q3

11

10 14 15

VCC = PIN 16 GND = PIN 8

LOGIC DIAGRAM
MR CP D3
1 9 13

D2
12

D1
5

D0
4

D Q CP Q CD
14 15

D Q CP Q CD
11 10

D Q CP Q CD
6 7

D Q CP Q CD
3 2

Q3 Q3

Q2 Q2
VCC = PIN 16 GND = PIN 8 = PIN NUMBERS

Q1 Q1

Q0 Q0

http://onsemi.com
144

SN74LS175
FUNCTIONAL DESCRIPTION

The LS175 consists of four edge-triggered D flip-flops with individual D inputs and Q and Q outputs. The Clock and Master Reset are common. The four flip-flops will store the state of their individual D inputs on the LOW to HIGH Clock (CP) transition, causing individual Q and Q outputs to

follow. A LOW input on the Master Reset (MR) will force all Q outputs LOW and Q outputs HIGH independent of Clock or Data inputs. The LS175 is useful for general logic applications where a common Master Reset and Clock are acceptable.

TRUTH TABLE
Inputs (t = n, MR = H) D L H Outputs (t = n+1) Note 1 Q L H Q H L

Note 1: t = n + 1 indicates conditions after next clock.

DC CHARACTERISTICS OVER OPERATING TEMPERATURE RANGE (unless otherwise specified)

Limits Symbol VIH VIL VIK VOH Parameter Input HIGH Voltage Input LOW Voltage Input Clamp Diode Voltage Output HIGH Voltage 2.7 0.65 3.5 0.25 VO OL Output LOW Voltage 0.35 IIH IIL IOS ICC Input HIGH Current 0.1 Input LOW Current Short Circuit Current (Note 1) Power Supply Current 20 0.4 100 18 0.5 20 V A mA mA mA mA IOL = 8.0 mA 0.4 Min 2.0 0.8 1.5 Typ Max Unit V V V V V Test Conditions Guaranteed Input HIGH Voltage for All Inputs Guaranteed Input LOW Voltage for All Inputs VCC = MIN, IIN = 18 mA VCC = MIN, IOH = MAX, VIN = VIH or VIL per Truth Table IOL = 4.0 mA VCC = VCC MIN, VIN = VIL or VIH per Truth Table

VCC = MAX, VIN = 2.7 V VCC = MAX, VIN = 7.0 V VCC = MAX, VIN = 0.4 V VCC = MAX VCC = MAX

Note 1: Not more than one output should be shorted at a time, nor for more than 1 second.

http://onsemi.com
145

SN74LS175
AC CHARACTERISTICS (TA = 25C)
Limits Symbol fMAX tPLH tPHL tPLH tPHL Parameter Maximum Input Clock Frequency Propagation Delay, MR to Output Propagation Delay, Clock to Output Min 30 Typ 40 20 20 13 16 30 30 25 25 Max Unit MHz ns ns VCC = 5.0 V CL = 15 pF F Test Conditions

AC SETUP REQUIREMENTS (TA = 25C)

Limits Symbol tW ts th trec Parameter Clock or MR Pulse Width Data Setup Time Data Hold Time Recovery Time Min 20 20 5.0 25 Typ Max Unit ns ns ns ns VCC = 5 0 V 5.0 Test Conditions

AC WAVEFORMS
1/fmax CP 1.3 V ts(H) D * 1.3 V th(H) ts(L) tw 1.3 V th(L) 1.3 V tPHL 1.3 V tPLH 1.3 V Q CP Q tPLH 1.3 V 1.3 V tPHL 1.3 V 1.3 V MR 1.3 V tW 1.3 V trec 1.3 V

1.3 V tPLH 1.3 V tPHL 1.3 V

Q Q

*The shaded areas indicate when the input is permitted to *change for predictable output performance.

Figure 1. Clock to Output Delays, Clock Pulse Width, Frequency, Setup and Hold Times Data to Clock

Figure 2. Master Reset to Output Delay, Master Reset Pulse Width, and Master Reset Recovery Time

DEFINITIONS OF TERMS

SETUP TIME (ts) is defined as the minimum time required for the correct logic level to be present at the logic input prior to the clock transition from LOW to HIGH in order to be recognized and transferred to the outputs. HOLD TIME (th) is defined as the minimum time following the clock transition from LOW to HIGH that the logic level must be maintained at the input in order to ensure

continued recognition. A negative HOLD TIME indicates that the correct logic level may be released prior to the clock transition from LOW to HIGH and still be recognized. RECOVERY TIME (trec) is defined as the minimum time required between the end of the reset pulse and the clock transition from LOW to HIGH in order to recognize and transfer HIGH Data to the Q outputs.

http://onsemi.com
146

SN74LS193 Presettable 4-Bit Binary Up/Down Counter

The SN74LS193 is an UP/DOWN MODULO-16 Binary Counter. Separate Count Up and Count Down Clocks are used and the circuits can operate synchronously. The outputs change state synchronous with the LOW-to-HIGH transitions on the clock inputs. Separate Terminal Count Up and Terminal Count Down outputs are provided which are used as the clocks for a subsequent stages without extra logic, thus simplifying multistage counter designs. Individual preset inputs allow the circuits to be used as programmable counters. Both the Parallel Load (PL) and the Master Reset (MR) inputs asynchronously override the clocks.
http://onsemi.com

LOW POWER SCHOTTKY

Low Power . . . 95 mW Typical Dissipation High Speed . . . 40 MHz Typical Count Frequency Synchronous Counting Asynchronous Master Reset and Parallel Load Individual Preset Inputs Cascading Circuitry Internally Provided Input Clamp Diodes Limit High Speed Termination Effects

16 1

GUARANTEED OPERATING RANGES

Symbol VCC TA IOH IOL Parameter Supply Voltage Operating Ambient Temperature Range Output Current High Output Current Low Min 4.75 0 Typ 5.0 25 Max 5.25 70 0.4 8.0 Unit V C
16

PLASTIC N SUFFIX CASE 648

mA mA

SOIC D SUFFIX CASE 751B

ORDERING INFORMATION
Device SN74LS193N SN74LS193D Package 16 Pin DIP 16 Pin Shipping 2000 Units/Box 2500/Tape & Reel

Semiconductor Components Industries, LLC, 1999

147

December, 1999 Rev. 0

Publication Order Number: SN74LS193/D

SN74LS193
CONNECTION DIAGRAM DIP (TOP VIEW)
VCC 16 P0 15 MR 14 TCD 13 TCU 12 PL 11 P2 10 P3 9 NOTE: The Flatpak version has the same pinouts (Connection Diagram) as the Dual In-Line Package. 1 P1 2 Q1 3 Q0 4 CPD 5 CPU 6 Q2 7 Q3 8 GND

LOADING (Note a) PIN NAMES CPU CPD MR PL Pn Qn TCD TCU Count Up Clock Pulse Input Count Down Clock Pulse Input Asynchronous Master Reset (Clear) Input Asynchronous Parallel Load (Active LOW) Input Parallel Data Inputs FlipFlop Outputs Terminal Count Down (Borrow) Output Terminal Count Up (Carry) Output HIGH 0.5 U.L. 0.5 U.L. 0.5 U.L. 0.5 U.L. 0.5 U.L. 10 U.L. 10 U.L. 10 U.L. LOW 0.25 U.L. 0.25 U.L. 0.25 U.L. 0.25 U.L. 0.25 U.L. 5 U.L. 5 U.L. 5 U.L.

NOTES: a) 1 TTL Unit Load (U.L.) = 40 mA HIGH/1.6 mA LOW.

LOGIC SYMBOL
11 15 1 10 9

PL 5 4 CPU CPD

P0 P1 P2

P3

TCU

12

MR Q0 Q1 Q2 Q3 14 3 2 6 7

TCD

13

VCC = PIN 16 GND = PIN 8

http://onsemi.com
148

SN74LS193
STATE DIAGRAM

15

LOGIC EQUATIONS FOR TERMINAL COUNT

TCU = Q0 Q1 Q2 Q3 CPU TCD = Q0 Q1 Q2 Q3 CPD

14

6 COUNT UP COUNT DOWN

13

12

11

10

LOGIC DIAGRAM
P0 PL (LOAD) CPU (UP COUNT)
11 5 12 15 1

P1
10

P2
9

P3

TCU (CARRY OUTPUT)

SD T

Q T

SD

Q T

SD

Q T

SD

CD Q

CD Q

CD Q

CD Q

13

CPD (DOWN COUNT) MR (CLEAR)

4 14 3 2 6 7

TCD (BORROW OUTPUT)

Q0 VCC = PIN 16 GND = PIN 8 = PIN NUMBERS

Q1

Q2

Q3

http://onsemi.com
149

SN74LS193
FUNCTIONAL DESCRIPTION

The LS193 is a 4-Bit Binary Synchronous UP / DOWN (Reversable) Counter. Each circuit contains four master/slave flip-flops, with internal gating and steering logic to provide master reset, individual preset, count up and count down operations. Each flip-flop contains JK feedback from slave to master such that a LOW-to-HIGH transition on its T input causes the slave, and thus the Q output to change state. Synchronous switching, as opposed to ripple counting, is achieved by driving the steering gates of all stages from a common Count Up line and a common Count Down line, thereby causing all state changes to be initiated simultaneously. A LOW-to-HIGH transition on the Count Up input will advance the count by one; a similar transition on the Count Down input will decrease the count by one. While counting with one clock input, the other should be held HIGH. Otherwise, the circuit will either count by twos or not at all, depending on the state of the first flip-flop, which cannot toggle as long as either Clock input is LOW. The Terminal Count Up (TCU) and Terminal Count Down (TCD) outputs are normally HIGH. When a circuit has

reached the maximum count state of 15, the next HIGH-to-LOW transition of the Count Up Clock will cause TCU to go LOW. TCU will stay LOW until CPU goes HIGH again, thus effectively repeating the Count Up Clock, but delayed by two gate delays. Similarly, the TCD output will go LOW when the circuit is in the zero state and the Count Down Clock goes LOW. Since the TC outputs repeat the clock waveforms, they can be used as the clock input signals to the next higher order circuit in a multistage counter. Each circuit has an asynchronous parallel load capability permitting the counter to be preset. When the Parallel Load (PL) and the Master Reset (MR) inputs are LOW, information present on the Parallel Data inputs (P0, P3) is loaded into the counter and appears on the outputs regardless of the conditions of the clock inputs. A HIGH signal on the Master Reset input will disable the preset gates, override both Clock inputs, and latch each Q output in the LOW state. If one of the Clock inputs is LOW during and after a reset or load operation, the next LOW-to-HIGH transition of that Clock will be interpreted as a legitimate signal and will be counted.

MODE SELECT TABLE

MR H L L L L PL X L H H H CPU X X H H CPD X X H H MODE Reset (Asyn.) Preset (Asyn.) No Change Count Up Count Down

L = LOW Voltage Level H = HIGH Voltage Level X = Dont Care = LOW-to-HIGH Clock Transition

http://onsemi.com
150

SN74LS193
DC CHARACTERISTICS OVER OPERATING TEMPERATURE RANGE (unless otherwise specified)
Limits Symbol VIH VIL VIK VOH Parameter Input HIGH Voltage Input LOW Voltage Input Clamp Diode Voltage Output HIGH Voltage 2.7 0.65 3.5 0.25 VO OL Output LOW Voltage 0.35 IIH IIL IOS ICC Input HIGH Current 0.1 Input LOW Current Short Circuit Current (Note 1) Power Supply Current 20 0.4 100 34 0.5 20 V A mA mA mA mA IOL = 8.0 mA 0.4 Min 2.0 0.8 1.5 Typ Max Unit V V V V V Test Conditions Guaranteed Input HIGH Voltage for All Inputs Guaranteed Input LOW Voltage for All Inputs VCC = MIN, IIN = 18 mA VCC = MIN, IOH = MAX, VIN = VIH or VIL per Truth Table IOL = 4.0 mA VCC = VCC MIN, VIN = VIL or VIH per Truth Table

VCC = MAX, VIN = 2.7 V VCC = MAX, VIN = 7.0 V VCC = MAX, VIN = 0.4 V VCC = MAX VCC = MAX

Note 1: Not more than one output should be shorted at a time, nor for more than 1 second.

AC CHARACTERISTICS (TA = 25C)

Limits Symbol fMAX tPLH tPHL tPLH tPHL tPLH tPHL tPLH tPHL tPHL Parameter Maximum Clock Frequency CPU Input to TCU Output CPD Input to TCD Output Clock to Q PL to Q MR Input to Any Output Min 25 Typ 32 17 18 16 15 27 30 24 25 23 26 24 24 24 38 47 40 40 35 Max Unit MHz ns ns ns ns ns VCC = 5.0 V CL = 15 pF Test Conditions

AC SETUP REQUIREMENTS (TA = 25C)

Limits Symbol tW ts th trec Parameter Any Pulse Width Data Setup Time Data Hold Time Recovery Time Min 20 20 5.0 40 Typ Max Unit ns ns ns ns VCC = 5 0 V 5.0 Test Conditions

DEFINITIONS OF TERMS

SETUP TIME (ts) is defined as the minimum time required for the correct logic level to be present at the logic input prior to the PL transition from LOW-to-HIGH in order to be recognized and transferred to the outputs. HOLD TIME (th) is defined as the minimum time following the PL transition from LOW-to-HIGH that the logic level must be maintained at the input in order to ensure continued

recognition. A negative HOLD TIME indicates that the correct logic level may be released prior to the PL transition from LOW-to-HIGH and still be recognized. RECOVERY TIME (trec) is defined as the minimum time required between the end of the reset pulse and the clock transition from LOW-to-HIGH in order to recognize and transfer HIGH data to the Q outputs.

http://onsemi.com
151

SN74LS193
AC WAVEFORMS

CPU or CPD

1.3 V tPHL

tW tPLH

1.3 V

1.3 V

1.3 V

Figure 1.

CPU or CPD tPHL TCU or TCD

1.3 V tPLH 1.3 V

Pn

1.3 V tPHL tPLH

Qn

1.3 V

NOTE: PL = LOW

Figure 2.

Figure 3.

Pn tw PL 1.3 V tPLH Qn

1.3 V PL tW tPHL 1.3 V Q CPU or CPD tPHL 1.3 V 1.3 V 1.3 V trec

Figure 4.

Figure 5.

Pn ts(H) PL

1.3 V th(H) ts(L) 1.3 V

1.3 V th(L) MR tW CPU or CPD Q=P Q 1.3 V trec 1.3 V tPHL 1.3 V

Qn

Q=P

* The shaded areas indicate when the input is permitted * to change for predictable output performance

Figure 6.

Figure 7.

http://onsemi.com
152

SN74LS194A 4-Bit Bidirectional Universal Shift Register

The SN74LS194A is a High Speed 4-Bit Bidirectional Universal Shift Register. As a high speed multifunctional sequential building block, it is useful in a wide variety of applications. It may be used in serial-serial, shift left, shift right, serial-parallel, parallel-serial, and parallel-parallel data register transfers. The LS194A is similar in operation to the LS195A Universal Shift Register, with added features of shift left without external connections and hold (do nothing) modes of operation. It utilizes the Schottky diode clamped process to achieve high speeds and is fully compatible with all ON Semiconductor TTL families.
http://onsemi.com

LOW POWER SCHOTTKY

Typical Shift Frequency of 36 MHz Asynchronous Master Reset Hold (Do Nothing) Mode Fully Synchronous Serial or Parallel Data Transfers Input Clamp Diodes Limit High Speed Termination Effects

16 1

GUARANTEED OPERATING RANGES

Symbol VCC TA IOH IOL Parameter Supply Voltage Operating Ambient Temperature Range Output Current High Output Current Low Min 4.75 0 Typ 5.0 25 Max 5.25 70 0.4 8.0 Unit V C mA mA
16

PLASTIC N SUFFIX CASE 648

SOIC D SUFFIX CASE 751B

ORDERING INFORMATION
Device SN74LS194AN SN74LS194AD Package 16 Pin DIP 16 Pin Shipping 2000 Units/Box 2500/Tape & Reel

Semiconductor Components Industries, LLC, 1999

153

December, 1999 Rev. 6

Publication Order Number: SN74LS194A/D

SN74LS194A
CONNECTION DIAGRAM DIP (TOP VIEW)
VCC 16 Q0 15 Q1 14 Q2 13 Q3 12 CP 11 S1 10 S0 9

1 MR

2 DSR

3 P0

4 P1

5 P2

6 P3

7 DSL

8 GND

LOADING (Note a) PIN NAMES S0, S1 P0 P3 DSR DSL CP MR Q0 Q3 Mode Control Inputs Parallel Data Inputs Serial (Shift Right) Data Input Serial (Shift Left) Data Input Clock (Active HIGH Going Edge) Input Master Reset (Active LOW) Input Parallel Outputs HIGH 0.5 U.L. 0.5 U.L. 0.5 U.L. 0.5 U.L. 0.5 U.L. 0.5 U.L. 10 U.L. LOW 0.25 U.L. 0.25 U.L. 0.25 U.L. 0.25 U.L. 0.25 U.L. 0.25 U.L. 5 U.L.

NOTES: a) 1 TTL Unit Load (U.L.) = 40 mA HIGH/1.6 mA LOW.

http://onsemi.com
154

SN74LS194A
LOGIC DIAGRAM
P0
10

P1
3 4

P2

P3
6

S1
9

S0
2

DSR

DSL

VCC = PIN 16 GND = PIN 8 = PIN NUMBERS

S CP

Q0

S CP

Q1

S CP

Q2

S CP

Q3

R CLEAR

R CLEAR

R CLEAR

R CLEAR

CP MR

11 1 15 14 13 12

Q0

Q1

Q2

Q3

FUNCTIONAL DESCRIPTION

The Logic Diagram and Truth Table indicate the functional characteristics of the LS194A 4-Bit Bidirectional Shift Register. The LS194A is similar in operation to the ON Semiconductor LS195A Universal Shift Register when used in serial or parallel data register transfers. Some of the common features of the two devices are described below: All data and mode control inputs are edge-triggered, responding only to the LOW to HIGH transition of the Clock (CP). The only timing restriction, therefore, is that the mode control and selected data inputs must be stable one set-up time prior to the positive transition of the clock pulse. The register is fully synchronous, with all operations taking place in less than 15 ns (typical) making the device especially useful for implementing very high speed CPUs, or the memory buffer registers. The four parallel data inputs (P0, P1, P2, P3) are D-type inputs. When both S0 and S1 are HIGH, the data appearing on P0, P1, P2, and P3 inputs is transferred to the Q0, Q1, Q2, and Q3 outputs respectively following the next LOW to HIGH transition of the clock.

The asynchronous Master Reset (MR), when LOW, overrides all other input conditions and forces the Q outputs LOW. Special logic features of the LS194A design which increase the range of application are described below: Two mode control inputs (S0, S1) determine the synchronous operation of the device. As shown in the Mode Selection Table, data can be entered and shifted from left to right (shift right, Q0 Q1, etc.) or right to left (shift left, Q3 Q2, etc.), or parallel data can be entered loading all four bits of the register simultaneously. When both S0 and S1,are LOW, the existing data is retained in a do nothing mode without restricting the HIGH to LOW clock transition. D-type serial data inputs (DSR, DSL) are provided on both the first and last stages to allow multistage shift right or shift left data transfers without interfering with parallel load operation.

http://onsemi.com
155

SN74LS194A
MODE SELECT TRUTH TABLE
OPERATING MODE Reset Hold Shift Left Shift Right Parallel Load INPUTS MR L H H H H H H S1 X I h h I I h S0 X I I I h h h DSR X X X X I h X DSL X X I h X X X Pn X X X X X X Pn Q0 L q0 q1 q1 L H P0 Q1 L q1 q2 q2 q0 q0 P1 OUTPUTS Q2 L q2 q3 q3 q1 q1 P2 Q3 L q3 L H q2 q2 P3

L = LOW Voltage Level H = HIGH Voltage Level X = Dont Care I = LOW voltage level one set-up time prior to the LOW to HIGH clock transition h = HIGH voltage level one set-up time prior to the LOW to HIGH clock transition pn (qn) = Lower case letters indicate the state of the referenced input (or output) one set-up time prior to the LOW to HIGH clock transition.

DC CHARACTERISTICS OVER OPERATING TEMPERATURE RANGE (unless otherwise specified)

Limits Symbol VIH VIL VIK VOH Parameter Input HIGH Voltage Input LOW Voltage Input Clamp Diode Voltage Output HIGH Voltage 2.7 0.65 3.5 0.25 VO OL Output LOW Voltage 0.35 IIH IIL IOS ICC Input HIGH Current 0.1 Input LOW Current Short Circuit Current (Note 1) Power Supply Current 20 0.4 100 23 0.5 20 V A mA mA mA mA IOL = 8.0 mA 0.4 Min 2.0 0.8 1.5 Typ Max Unit V V V V V Test Conditions Guaranteed Input HIGH Voltage for All Inputs Guaranteed Input LOW Voltage for All Inputs VCC = MIN, IIN = 18 mA VCC = MIN, IOH = MAX, VIN = VIH or VIL per Truth Table IOL = 4.0 mA VCC = VCC MIN, VIN = VIL or VIH per Truth Table

VCC = MAX, VIN = 2.7 V VCC = MAX, VIN = 7.0 V VCC = MAX, VIN = 0.4 V VCC = MAX VCC = MAX

Note 1: Not more than one output should be shorted at a time, nor for more than 1 second.

AC CHARACTERISTICS (TA = 25C)

Limits Symbol fMAX tPLH tPHL tPHL Parameter Maximum Clock Frequency Propagation Delay, Clock to Output Propagation Delay, MR to Output Min 25 Typ 36 14 17 19 22 26 30 Max Unit MHz ns ns VCC = 5.0 V CL = 15 pF F Test Conditions

http://onsemi.com
156

SN74LS194A
AC SETUP REQUIREMENTS (TA = 25C)
Limits Symbol tW ts ts th trec Parameter Clock or MR Pulse Width Mode Control Setup Time Data Setup Time Hold time, Any Input Recovery Time Min 20 30 20 0 25 Typ Max Unit ns ns ns ns ns VCC = 5.0 V Test Conditions

DEFINITIONS OF TERMS

SETUP TIME(ts) is defined as the minimum time required for the correct logic level to be present at the logic input prior to the clock transition from LOW to HIGH in order to be recognized and transferred to the outputs. HOLD TIME (th) is defined as the minimum time following the clock transition from LOW to HIGH that the logic level must be maintained at the input in order to ensure

continued recognition. A negative HOLD TIME indicates that the correct logic level may be released prior to the clock transition from LOW to HIGH and still be recognized. RECOVERY TIME (trec) is defined as the minimum time required between the end of the reset pulse and the clock transition from LOW to HIGH in order to recognize and transfer HIGH Data to the Q outputs.

AC WAVEFORMS
The shaded areas indicate when the input is permitted to change for predictable output performance. S0 1/fmax 1.3 V CLOCK tPHL OUTPUT 1.3 V tW tPLH 1.3 V P0 P1 P2 P3 ts(L) th(L) = 0 CLOCK OUTPUT* 1.3 V ts(H) th(H) = 0 1.3 V 1.3 V S1 1.3 V ts(L) th(L) = 0 ts(H) th(H) = 0

( IS SHIFT LEFT)

DSR DSL

OTHER CONDITIONS: S1 = L, MR = H, S0 = H

Figure 1. Clock to Output Delays Clock Pulse Width and fmax

MR

1.3 V tW trec 1.3 V

OTHER CONDITIONS: MR = H OTHER CONDITIONS: *DSR SET-UP TIME AFFECTS Q0 ONLY OTHER CONDITIONS: DSL SET-UP TIME AFFECTS Q3 ONLY

CLOCK tPHL OUTPUT

Figure 3. Setup (ts) and Hold (th) Time for Serial Data (DSR, DSL) and Parallel Data (P0, P1, P2, P3)

(STABLE TIME) 1.3 V S0 S1 1.3 V ts th = 0 CLOCK 1.3 V OTHER CONDITIONS: MR = H ts th = 0 1.3 V

OTHER CONDITIONS: S0, S1 = H OTHER CONDITIONS: PO = P1 = P2 = P3 = H

Figure 2. Master Reset Pulse Width, Master Reset to Output Delay and Master Reset to Clock Recovery Time

Figure 4. Setup (ts) and Hold (th) Time for S Input

http://onsemi.com
157

SN74LS195A Universal 4-Bit Shift Register

The SN74LS195A is a high speed 4-Bit Shift Register offering typical shift frequencies of 39 MHz. It is useful for a wide variety of register and counting applications. It utilizes the Schottky diode clamped process to achieve high speeds and is fully compatible with all ON Semiconductor TTL products.
http://onsemi.com

Typical Shift Right Frequency of 39 MHz Asynchronous Master Reset J, K Inputs to First Stage Fully Synchronous Serial or Parallel Data Transfers Input Clamp Diodes Limit High Speed Termination Effects

LOW POWER SCHOTTKY

GUARANTEED OPERATING RANGES

Symbol VCC TA IOH IOL Parameter Supply Voltage Operating Ambient Temperature Range Output Current High Output Current Low Min 4.75 0 Typ 5.0 25 Max 5.25 70 0.4 8.0 Unit V C mA mA
16 1

PLASTIC N SUFFIX CASE 648

16 1

SOIC D SUFFIX CASE 751B

ORDERING INFORMATION
Device SN74LS195AN SN74LS195AD Package 16 Pin DIP 16 Pin Shipping 2000 Units/Box 2500/Tape & Reel

Semiconductor Components Industries, LLC, 1999

158

December, 1999 Rev. 6

Publication Order Number: SN74LS195A/D

SN74LS195A
CONNECTION DIAGRAM DIP (TOP VIEW)
VCC 16 Q0 15 Q1 14 Q2 13 Q3 12 Q3 11 CP 10 PE 9 NOTE: The Flatpak version has the same pinouts (Connection Diagram) as the Dual In-Line Package.

1 MR

2 J

3 K

4 P0

5 P1

6 P2

7 P3

8 GND

LOADING (Note a) PIN NAMES PE P0 P3 J K CP MR Q0 Q3 Q3 Parallel Enable (Active LOW) Input Parallel Data Inputs First Stage J (Active HIGH) Input First Stage K (Active LOW) Input Clock (Active HIGH Going Edge) Input Master Reset (Active LOW) Input Parallel Outputs Complementary Last Stage Output HIGH 0.5 U.L. 0.5 U.L. 0.5 U.L. 0.5 U.L. 0.5 U.L. 0.5 U.L. 10 U.L. 10 U.L. LOW 0.25 U.L. 0.25 U.L. 0.25 U.L. 0.25 U.L. 0.25 U.L. 0.25 U.L. 5 U.L. 5 U.L.

NOTES: a) 1 TTL Unit Load (U.L.) = 40 mA HIGH/1.6 mA LOW.

LOGIC SYMBOL
9 4 5 6 7

2 10 3

J K

PE P0 P1 P2 P3 Q3 11

CP MR Q0 Q1 Q2 Q3 1 15 14 13 12 VCC = PIN 16 GND = PIN 8

http://onsemi.com
159

SN74LS195A
LOGIC DIAGRAM
PE J
9 2 3

K
4

P0
5

P1
6

P2
7

P3
1

MR
10

CP

R CD Q0 CP S VCC = PIN 16 GND = PIN 8 = PIN NUMBERS Q0

15

R CD CP S Q0
14

R CD CP S Q2
13

R CD Q3 CP S Q3
12 11

Q0

Q1

Q2

Q3 Q3

FUNCTIONAL DESCRIPTION

The Logic Diagram and Truth Table indicate the functional characteristics of the LS195A 4-Bit Shift Register. The device is useful in a wide variety of shifting, counting and storage applications. It performs serial, parallel, serial to parallel, or parallel to serial data transfers at very high speeds. The LS195A has two primary modes of operation, shift right (Q0 Q1) and parallel load which are controlled by the state of the Parallel Enable (PE) input. When the PE input is HIGH, serial data enters the first flip-flop Q0 via the J and K inputs and is shifted one bit in the direction Q0 Q1 Q2 Q3 following each LOW to HIGH clock transition. The JK inputs provide the flexibility of the JK type input for special applications, and the simple D type input for general applications by tying the two pins together. When the PE

input is LOW, the LS195A appears as four common clocked D flip-flops. The data on the parallel inputs P0, P1, P2, P3 is transferred to the respective Q0, Q1, Q2, Q3 outputs following the LOW to HIGH clock transition. Shift left operations (Q3 Q2) can be achieved by tying the Qn Outputs to the Pn1 inputs and holding the PE input LOW. All serial and parallel data transfers are synchronous, occurring after each LOW to HIGH clock transition. Since the LS195A utilizes edge-triggering, there is no restriction on the activity of the J, K, Pn and PE inputs for logic operation except for the set-up and release time requirements. A LOW on the asynchronous Master Reset (MR) input sets all Q outputs LOW, independent of any other input condition.

MODE SELECT TRUTH TABLE

INPUTS OPERATING MODES MR Asynchronous Reset Shift, Set First Stage Shift, Reset First Shift, Toggle First Stage Shift, Retain First Stage Parallel Load L H H H H H PE X h h h h I J X h I h I X K X h I I h X Pn X X X X X pn Q0 L H L q0 q0 p0 Q1 L q0 q0 q0 q0 p1 Q2 L q1 q1 q1 q1 p2 Q3 L q2 q2 q2 q2 p3 Q3 H q2 q2 q2 q2 p3 OUTPUTS

L = LOW voltage levels H = HIGH voltage levels X = Dont Care I = LOW voltage level one set-up time prior to the LOW to HIGH clock transition. h = HIGH voltage level one set-up time prior to the LOW to HIGH clock transition. pn (qn) = Lower case letters indicate the state of the referenced input (or output) one set-up time prior to the LOW to HIGH clock transition.

http://onsemi.com
160

SN74LS195A
DC CHARACTERISTICS OVER OPERATING TEMPERATURE RANGE (unless otherwise specified)
Limits Symbol VIH VIL VIK VOH Parameter Input HIGH Voltage Input LOW Voltage Input Clamp Diode Voltage Output HIGH Voltage 2.7 0.65 3.5 0.25 VO OL Output LOW Voltage 0.35 IIH IIL IOS ICC Input HIGH Current 0.1 Input LOW Current Short Circuit Current (Note 1) Power Supply Current 20 0.4 100 21 0.5 20 V A mA mA mA mA IOL = 8.0 mA 0.4 Min 2.0 0.8 1.5 Typ Max Unit V V V V V Test Conditions Guaranteed Input HIGH Voltage for All Inputs Guaranteed Input LOW Voltage for All Inputs VCC = MIN, IIN = 18 mA VCC = MIN, IOH = MAX, VIN = VIH or VIL per Truth Table IOL = 4.0 mA VCC = VCC MIN, VIN = VIL or VIH per Truth Table

VCC = MAX, VIN = 2.7 V VCC = MAX, VIN = 7.0 V VCC = MAX, VIN = 0.4 V VCC = MAX VCC = MAX

Note 1: Not more than one output should be shorted at a time, nor for more than 1 second.

AC CHARACTERISTICS (TA = 25C)

Limits Symbol fMAX tPLH tPHL tPHL Parameter Maximum Clock Frequency Propagation Delay, Clock to Output Propagation Delay, MR to Output Min 30 Typ 39 14 17 19 22 26 30 Max Unit MHz ns ns VCC = 5.0 V CL = 15 pF F Test Conditions

AC SETUP REQUIREMENTS (TA = 25C)

Limits Symbol tW tW ts ts trec trel th Parameter CP Clock Pulse Width MR Pulse Width PE Setup Time Data Setup Time Recovery Time PE Release Time Data Hold Time 0 Min 16 12 25 15 25 10 Typ Max Unit ns ns ns ns ns ns ns VCC = 5.0 V Test Conditions

http://onsemi.com
161

SN74LS195A
DEFINITIONS OF TERMS

SETUP TIME(ts) is defined as the minimum time required for the correct logic level to be present at the logic input prior to the clock transition from LOW to HIGH in order to be recognized and transferred to the outputs. HOLD TIME (th) is defined as the minimum time following the clock transition from LOW to HIGH that the logic level must be maintained at the input in order to ensure

continued recognition. A negative HOLD TIME indicates that the correct logic level may be released prior to the clock transition from LOW to HIGH and still be recognized. RECOVERY TIME (trec) is defined as the minimum time required between the end of the reset pulse and the clock transition from LOW to HIGH in order to recognize and transfer HIGH Data to the Q outputs.

AC WAVEFORMS
The shaded areas indicate when the input is permitted to change for predictable output performance.

PE 1.3 V ts(L) th(L) = 0 P0 P1 P2 P3 1.3 V CLOCK tPHL OUTPUT 1.3 V CONDITIONS: J = PE = MR = H K=L 1.3 V tPLH 1.3 V th(L) = 0 CLOCK OUTPUT* ts(L) ts(H) th(H) = 0 1.3 V 1.3 V ts(H) th(H) = 0

J&K tW

CONDITIONS: MR = H *J AND K SETUP TIME AFFECTS Q0 ONLY

Figure 1. Clock to Output Delays and Clock Pulse Width

Figure 3. Setup (ts) and Hold (th) Time for Serial Data (J & K) and Parallel Data (P0, P1, P2, P3)

MR

tW 1.3 V 1.3 V trec PE ts(L) CLOCK 1.3 V OUTPUT Qn = Pn Qn* = Qn1 trel 1.3 V LOAD PARALLEL DATA 1.3 V 1.3 V ts(H) trel 1.3 V LOAD SERIAL DATA SHIFT RIGHT

CLOCK tPHL OUTPUT

1.3 V

CONDITIONS: PE = L PO = P1 = P2 = P3 = H

Figure 2. Master Reset Pulse Width, Master Reset to Output Delay and Master Reset to Clock Recovery Time

CONDITIONS: MR = H *Q0 STATE WILL BE DETERMINED BY J AND K INPUTS.

Figure 4. Setup (ts) and Hold (th) Time for PE Input

http://onsemi.com
162

SN74LS221 Dual Monostable Multivibrators with Schmitt-Trigger Inputs

Each multivibrator of the LS221 features a negative-transitiontriggered input and a positive-transition-triggered input either of which can be used as an inhibit input. Pulse triggering occurs at a voltage level and is not related to the transition time of the input pulse. Schmitt-trigger input circuitry for B input allows jitter-free triggering for inputs as slow as 1 volt / second, providing the circuit with excellent noise immunity. A high immunity to VCC noise is also provided by internal latching circuitry. Once triggered, the outputs are independent of further transitions of the inputs and are a function of the timing components. The output pulses can be terminated by the overriding clear. Input pulse width may be of any duration relative to the output pulse width. Output pulse width may be varied from 35 nanoseconds to a maximum of 70 s by choosing appropriate timing components. With Rext = 2.0 k and Cext = 0, a typical output pulse of 30 nanoseconds is achieved. Output rise and fall times are independent of pulse length. Pulse width stability is achieved through internal compensation and is virtually independent of VCC and temperature. In most applications, pulse stability will only be limited by the accuracy of external timing components. Jitter-free operation is maintained over the full temperature and VCC ranges for greater than six decades of timing capacitance (10 pF to 10 F), and greater than one decade of timing resistance (2.0 to 100 k for the SN74LS221). Pulse width is defined by the relationship: tw(out) = CextRext ln 2.0 0.7 Cext Rext; where tW is in ns if Cext is in pF and Rext is in k. If pulse cutoff is not critical, capacitance up to 1000 F and resistance as low as 1.4 k may be used. The range of jitter-free pulse widths is extended if VCC is 5.0 V and 25C temperature.
http://onsemi.com

LOW POWER SCHOTTKY

16 1

PLASTIC N SUFFIX CASE 648

16 1

SOIC D SUFFIX CASE 751B

SN74LS221 is a Dual Highly Stable One-Shot Overriding Clear Terminates Output Pulse Pin Out is Identical to SN74LS123
ORDERING INFORMATION GUARANTEED OPERATING RANGES
Symbol VCC TA IOH IOL Parameter Supply Voltage Operating Ambient Temperature Range Output Current High Output Current Low Min 4.75 0 Typ 5.0 25 Max 5.25 70 0.4 8.0 Unit V C mA mA SN74LS221D 16 Pin 2500/Tape & Reel Device SN74LS221N Package 16 Pin DIP Shipping 2000 Units/Box

Semiconductor Components Industries, LLC, 1999

163

December, 1999 Rev. 6

Publication Order Number: SN74LS221/D

SN74LS221
(TOP VIEW)
VCC 16 1 Rext/ 1 Cext Cext 15 14 Q Q CLR 1Q 13 2Q 12 2 CLR 11 2B 10 2A 9

CLR Q Q 4 1Q 5 2Q 6 2 Cext 8 7 2 Rext/ GND Cext

1 1A

2 1B

3 1 CLR

Positive logic: Low input to clear resets Q low and Positive logic: Q high regardless of dc levels at A Positive logic: or B inputs.

VCC Rext + Cext R/C

FUNCTION TABLE (EACH MONOSTABLE)

INPUTS CLEAR L X X H H
*

OUTPUTS B X X L H H Q L L L Q H H H

A X H X L L

*See operational notes Pulse Trigger Modes

TYPE SN74LS221

TYPICAL POWER DISSIPATION 23 mW

MAXIMUM OUTPUT PULSE LENGTH 70 s

http://onsemi.com
164

SN74LS221
OPERATIONAL NOTES

Once in the pulse trigger mode, the output pulse width is determined by tW = RextCextIn2, as long as Rext and Cext are within their minimum and maximum valves and the duty cycle is less than 50%. This pulse width is essentially independent of VCC and temperature variations. Output pulse widths varies typically no more than 0.5% from device to device. t If the duty cycle, defined as being 100 @ W where T is the T period of the input pulse, rises above 50%, the output pulse width will become shorter. If the duty cycle varies between low and high valves, this causes the output pulse width to vary in length, or jitter. To reduce jitter to a minimum, Rext should be as large as possible. (Jitter is independent of Cext). With Rext = 100K, jitter is not appreciable until the duty cycle approaches 90%. Although the LS221 is pin-for-pin compatible with the LS123, it should be remembered that they are not functionally identical. The LS123 is retriggerable so that the output is dependent upon the input transitions once it is high. This is not the case for the LS221. Also note that it is recommended to externally ground the LS123 Cext pin. However, this cannot be done on the LS221. The SN74LS221 is a dual, monolithic, non-retriggerable, high-stability one shot. The output pulse width, tW can be varied over 9 decades of timing by proper selection of the external timing components, Rext and Cext. Pulse triggering occurs at a voltage level and is, therefore, independent of the input slew rate. Although all three inputs have this Schmitt-trigger effect, only the B input should be used for very long transition triggers (1.0 V/s). High immunity to VCC noise (typically 1.5 V) is achieved by internal latching circuitry. However, standard VCC bypassing is strongly recommended. The LS221 has four basic modes of operation.

Clear Mode:

If the clear input is held low, irregardless of the previous output state and other input states, the Q output is low. If either the A input is high or the B input is low, once the Q output goes low, it cannot be retriggered by other inputs.

Inhibit Mode:

Pulse Trigger Mode: A transition of the A or B inputs as indicated in the functional truth table will trigger the Q output to go high for a duration determined by the tW equation described above; Q will go low for a corresponding length of time. The Clear input may also be used to trigger an output pulse, but special logic preconditioning on the A or B inputs must be done as follows: Following any output triggering action using the A or B inputs, the A input must be set high OR the B input must be set low to allow Clear to be used as a trigger. Inputs should then be set up per the truth table (without triggering the output) to allow Clear to be used a trigger for the output pulse. If the Clear pin is routinely being used to trigger the output pulse, the A or B inputs must be toggled as described above before and between each Clear trigger event. Once triggered, as long as the output remains high, all input transitions (except overriding Clear) are ignored. Overriding Clear Mode: If the Q output is high, it may be forced low by bringing the clear input low.

http://onsemi.com
165

SN74LS221
DC CHARACTERISTICS OVER OPERATING TEMPERATURE RANGE (unless otherwise specified)
Limits Symbol VT+ VT Parameter Positive-Going Threshold Voltage at C Input Negative-Going Threshold Voltage at C Input Positive-Going Threshold Voltage at B Input Negative-Going Threshold Voltage at B Input Input HIGH Voltage Input LOW Voltage Input Clamp Voltage Output HIGH Voltage Output LOW Voltage Input HIGH Current 0.1 Input LOW Current Input A Input B Clear Short Circuit Current (Note 1) Power Supply Current Quiescent Triggered 20 4.7 19 0.4 0.8 0.8 100 11 27 2.7 3.4 0.35 0.5 20 IIH 0.8 0.7 Min Typ 1.0 0.8 Max 2.0 Unit V V VCC = MIN VCC = MIN VCC = MIN VCC = MIN Guaranteed Input HIGH Voltage for A Input Guaranteed Input LOW Voltage for A Input VCC = MIN, IIN = 18 mA VCC = MIN, IOH = MAX IOL = 8.0 mA VCC = MIN Test Conditions

VT+ VT

1.0 0.9

2.0

V V

VIH VIL VIK VOH VOL

2.0 0.8 1.5

V V V V V A mA

VCC = MAX, VIN = 2.7 V VCC = MAX, VIN = 7.0 V

IIL

mA

VCC = MAX, VIN = 0.4 V

IOS ICC

mA

VCC = MAX VCC = MAX

mA

Note 1: Not more than one output should be shorted at a time, nor for more than 1 second.

http://onsemi.com
166

SN74LS221
AC CHARACTERISTICS (VCC = 5.0 V, TA = 25C)
Symbol tPLH From (Input) A B A tPHL tPHL tPLH B Clear Clear To (Output) Q Q Q Q Q Q 70 20 tW(out) ( ) A or B Q or Q 600 6.0 670 6.9 750 7.5 ms Limits Min Typ 45 35 50 40 35 44 120 47 Max 70 ns 55 80 ns 65 55 65 150 70 ns ns ns CL = 15 pF, See Figure 1 Cext = 80 pF, Rext = 2.0 Cext = 0, Rext = 2.0 k Cext = 100 pF, Rext = 10 k Cext = 1.0 F, Rext = 10 k Cext = 80 pF Rext = 2.0 pF, 20 Unit Test Conditions

AC SETUP REQUIREMENTS (VCC = 5.0 V, TA = 25C)

Limits Symbol Parameter Rate of Rise or Fall of Input Pulse dv/dt Schmitt, B Logic Input, A Input Pulse Width tW ts Rext Cext Clear-Inactive-State Setup Time External Timing Resistance External Timing Capacitance Output Duty Cycle RT = 2.0 k RT = MAX Rext 50 90 % A or B, tW(in) Clear, tW (clear) 40 40 15 1.4 0 100 1000 ns k F ns 1.0 1.0 V/s V/s Min Typ Max Unit

http://onsemi.com
167

SN74LS221
AC WAVEFORMS

tW(in) B INPUT 60 ns CLEAR tPLH Q OUTPUT tPHL Q OUTPUT A INPUT IS LOW.

TRIGGER FROM B, THEN CLEAR CONDITION 1

3V 1.3 V 0V 3V tPHL 0V VOH VOL VOH VOL

tPLH

3V B INPUT 60 ns CLEAR Q OUTPUT A INPUT IS LOW.

TRIGGER FROM B, THEN CLEAR CONDITION 2

0V 1.3 V 3V 0V VOH VOL

B INPUT 50 ns CLEAR TRIGGERED Q OUTPUT NOT TRIGGERED A INPUT IS LOW. tW(out) 0 ts

3V 0V 3V 0V VOH VOL

CLEAR OVERRIDING B, THEN TRIGGER FROM B

B INPUT 50 ns CLEAR 50 ns 1.3 V

3V 0V 3V 0V

Q OUTPUT A INPUT IS LOW.

TRIGGERING FROM POSITIVE TRANSITION OF CLEAR

VOH VOL

Figure 1.

http://onsemi.com
168

SN74LS240 SN74LS244 Octal Buffer/Line Driver with 3-State Outputs

The SN74LS240 and SN74LS244 are Octal Buffers and Line Drivers designed to be employed as memory address drivers, clock drivers and bus-oriented transmitters/receivers which provide improved PC board density.
http://onsemi.com

Hysteresis at Inputs to Improve Noise Margins 3-State Outputs Drive Bus Lines or Buffer Memory Address Input Clamp Diodes Limit High-Speed Termination Effects
GUARANTEED OPERATING RANGES
Symbol VCC TA IOH Parameter Supply Voltage Operating Ambient Temperature Range Output Current High Min 4.75 0 Typ 5.0 25 Max 5.25 70 3.0 15 IOL Output Current Low 24 Unit V C
20

Registers

LOW POWER SCHOTTKY

mA mA mA

PLASTIC N SUFFIX CASE 738

20 1

SOIC DW SUFFIX CASE 751D

ORDERING INFORMATION
Device SN74LS240N SN74LS240DW SN74LS244N SN74LS244DW Package 16 Pin DIP 16 Pin 16 Pin DIP 16 Pin Shipping 1440 Units/Box 2500/Tape & Reel 1440 Units/Box 2500/Tape & Reel

Semiconductor Components Industries, LLC, 1999

169

December, 1999 Rev. 6

Publication Order Number: SN74LS240/D

SN74LS240 SN74LS244
LOGIC AND CONNECTION DIAGRAMS DIP (TOP VIEW) SN74LS240
VCC 20 2G 19 1Y1 18 2A4 1Y2 2A3 1Y3 2A2 1Y4 2A1 17 16 15 14 13 12 11

1 1G

2 1A1

3 4 5 2Y4 1A2 2Y3

6 8 9 10 7 1A3 2Y2 1A4 2Y1 GND

SN74LS244
VCC 20 2G 19 1Y1 18 2A4 1Y2 2A3 1Y3 2A2 1Y4 2A1 17 16 15 14 13 12 11

1 1G

2 1A1

3 4 5 2Y4 1A2 2Y3

6 8 9 10 7 1A3 2Y2 1A4 2Y1 GND

TRUTH TABLES SN74LS240

INPUTS OUTPUT 1G, 2G L L H D L H X H L (Z)
H = HIGH Voltage Level L = LOW Voltage Level X = Immaterial Z = HIGH Impedance

SN74LS244
INPUTS OUTPUT 1G, 2G L L H D L H X L H (Z)

http://onsemi.com
170

SN74LS240 SN74LS244
DC CHARACTERISTICS OVER OPERATING TEMPERATURE RANGE (unless otherwise specified)
Limits Symbol VIH VIL VT+VT VIK VO OH Parameter Input HIGH Voltage Input LOW Voltage Hysteresis Input Clamp Diode Voltage 2.4 Output HIGH Voltage 2.0 0.25 VO OL IOZH IOZL IIH IIL IOS Output LOW Voltage 0.35 Output Off Current HIGH Output Off Current LOW Input HIGH Current 0.1 Input LOW Current Output Short Circuit Current (Note 1) Power Supply Current Total, Output HIGH Total, Output LOW ICC Total at HIGH Z LS240 LS244 LS240 LS244 40 0.2 225 27 44 46 50 54 mA A VCC = MAX 0.5 20 20 20 V A A A mA mA mA IOL = 24 mA 0.4 V V 0.2 0.4 0.65 3.4 1.5 Min 2.0 0.8 Typ Max Unit V V V V V Test Conditions Guaranteed Input HIGH Voltage for All Inputs Guaranteed Input LOW Voltage for All Inputs VCC = MIN VCC = MIN, IIN = 18 mA VCC = MIN, IOH = 3.0 mA VCC = MIN, IOH = MAX IOL = 12 mA VCC = VCC MIN, VIN = VIL or VIH per Truth Table

VCC = MAX, VOUT = 2.7 V VCC = MAX, VOUT = 0.4 V VCC = MAX, VIN = 2.7 V VCC = MAX, VIN = 7.0 V VCC = MAX, VIN = 0.4 V VCC = MAX

Note 1: Not more than one output should be shorted at a time, nor for more than 1 second.

AC CHARACTERISTICS (TA = 25C, VCC = 5.0 V)

Limits Symbol tPLH tPHL tPLH tPHL tPZH tPZL tPLZ tPHZ Parameter Propagation Delay, Data to Output LS240 Propagation Delay, Data to Output LS244 Output Enable Time to HIGH Level Output Enable Time to LOW Level Output Disable Time from LOW Level Output Disable Time from HIGH Level Min Typ 9.0 12 12 12 15 20 15 10 Max 14 18 18 18 23 30 25 18 Unit ns ns ns ns ns ns CL = 5.0 pF, RL = 667 CL = 45 pF, RL = 667 Test Conditions

http://onsemi.com
171

SN74LS240 SN74LS244
AC WAVEFORMS

VIN

1.3 V tPLH

1.3 V tPHL 1.3 V

VCC RL

VOUT

1.3 V

Figure 1.

SW1

TO OUTPUT UNDER TEST VIN 1.3 V tPHL VOUT 1.3 V 1.3 V tPLH 1.3 V CL* 5 k SW2

Figure 2.

VE VE VOUT

1.3 V tPZL 1.3 V

1.3 V tPLZ 1.3 V VOL 0.5 V

SWITCH POSITIONS
SYMBOL tPZH tPZL tPLZ tPHZ SW1 Open Closed Closed Closed SW2 Closed Open Closed Closed

Figure 3.

Figure 5.
VE 1.3 V VE VOUT tPZH 1.3 V 1.3 V tPHZ VOH 1.3 V 0.5 V

Figure 4.

http://onsemi.com
172

SN74LS245 Octal Bus Transceiver

The SN74LS245 is an Octal Bus Transmitter/Receiver designed for 8-line asynchronous 2-way data communication between data buses. Direction Input (DR) controls transmission of Data from bus A to bus B or bus B to bus A depending upon its logic level. The Enable input (E) can be used to isolate the buses.
http://onsemi.com

Hysteresis Inputs to Improve Noise Immunity 2-Way Asynchronous Data Bus Communication Input Diodes Limit High-Speed Termination Effects ESD > 3500 Volts
LOGIC AND CONNECTION DIAGRAMS DIP (TOP VIEW)
VCC 20 E 19 B1 18 B2 17 B3 16 B4 15 B5 14 B6 13 B7 12 B8 11

LOW POWER SCHOTTKY

20 1

1 DIR

2 A1

3 A2

4 A3

5 A4

6 A5

7 A6

8 A7

9 A8

10 GND

PLASTIC N SUFFIX CASE 738

TRUTH TABLE
INPUTS OUTPUT E L L H DIR L H X Bus B Data to Bus A Bus A Data to Bus B Isolation
20 1

H = HIGH Voltage Level L = LOW Voltage Level X = Immaterial

SOIC DW SUFFIX CASE 751D

GUARANTEED OPERATING RANGES

Symbol VCC TA IOH Parameter Supply Voltage Operating Ambient Temperature Range Output Current High Min 4.75 0 Typ 5.0 25 Max 5.25 70 3.0 15 IOL Output Current Low 24 Unit V C mA mA mA Device SN74LS245N SN74LS245DW Package 16 Pin DIP 16 Pin Shipping 1440 Units/Box 2500/Tape & Reel

ORDERING INFORMATION

Semiconductor Components Industries, LLC, 1999

173

December, 1999 Rev. 6

Publication Order Number: SN74LS245/D

SN74LS245
DC CHARACTERISTICS OVER OPERATING TEMPERATURE RANGE (unless otherwise specified)
Limits Symbol VIH VIL VT+VT VIK VO OH Parameter Input HIGH Voltage Input LOW Voltage Hysteresis Input Clamp Diode Voltage 2.4 Output HIGH Voltage 2.0 0.25 VO OL IOZH IOZL Output LOW Voltage 0.35 Output Off Current HIGH Output Off Current LOW A or B, DR or E IIH Input HIGH C I t Current t DR or E A or B IIL IOS Input LOW Current Output Short Circuit Current (Note 1) Power Supply Current Total, Output HIGH ICC Total, Output LOW Total at HIGH Z 40 0.5 20 200 20 0.1 0.1 0.2 225 70 90 95 mA A VCC = MAX V A A A mA mA mA mA IOL = 24 mA 0.4 V V 0.2 0.4 0.65 3.4 1.5 Min 2.0 0.8 Typ Max Unit V V V V V Test Conditions Guaranteed Input HIGH Voltage for All Inputs Guaranteed Input LOW Voltage for All Inputs VCC = MIN VCC = MIN, IIN = 18 mA VCC = MIN, IOH = 3.0 mA VCC = MIN, IOH = MAX IOL = 12 mA VCC = VCC MIN, VIN = VIL or VIH per Truth Table

VCC = MAX, VOUT = 2.7 V VCC = MAX, VOUT = 0.4 V VCC = MAX, VIN = 2.7 V VCC = MAX, VIN = 7.0 V VCC = MAX, VIN = 5.5 V VCC = MAX, VIN = 0.4 V VCC = MAX

Note 1: Not more than one output should be shorted at a time, nor for more than 1 second.

AC CHARACTERISTICS (TA = 25C, VCC = 5.0 V, TRISE / TFALL 6.0 ns)

Limits Symbol tPLH tPHL tPZH tPZL tPLZ tPHZ Parameter Propagation Delay, Data to Output Output Enable Time to HIGH Level Output Enable Time to LOW Level Output Disable Time from LOW Level Output Disable Time from HIGH Level Min Typ 8.0 8.0 25 27 15 15 Max 12 12 40 40 25 25 Unit ns ns ns ns ns CL = 5.0 pF, RL = 667 CL = 45 pF, F, RL = 667 Test Conditions

http://onsemi.com
174

SN74LS247 BCD-to-Seven-Segment Decoders/Drivers

The SN74LS247 is a BCD-to-Seven-Segment Decoder/Drivers. The LS247 composes the and with the tails. The LS247 has active-low outputs for direct drive of indicators. The LS247 features a lamp test input and have full ripple-blanking input/output controls. An automatic leading and/or trailing-edge zero-blanking control (RBI and RBO) is incorporated and an overriding blanking input (BI) is contained which may be used to control the lamp intensity by pulsing or to inhibit the outputs lamp test may be performed at any time when the BI/RBO node is at high level. Segment identification and resultant displays are shown below. Display pattern for BCD input counts above 9 are unique symbols to authenticate input conditions.
http://onsemi.com

LOW POWER SCHOTTKY

Open-Collector Outputs Drive Indicators Directly Lamp-Test Provision Leading/ Trailing Zero Suppression
GUARANTEED OPERATING RANGES
Symbol VCC TA IOH IOL VO(off) IO(on) Parameter Supply Voltage Operating Ambient Temperature Range Output Current High BI/RBO Output Current Low BI/RBO OffState Output Voltage ag OnState Output Current ag Min 4.75 0 Typ 5.0 25 Max 5.25 70 50 3.2 15 24 Unit V C

16 1

PLASTIC N SUFFIX CASE 648

mA
16

mA V mA

SOIC D SUFFIX CASE 751B

ORDERING INFORMATION
Device SN74LS247N SN74LS247D Package 16 Pin DIP 16 Pin Shipping 2000 Units/Box 2500/Tape & Reel

Semiconductor Components Industries, LLC, 1999

175

December, 1999 Rev. 6

Publication Order Number: SN74LS247/D

SN74LS247

10

11

12

13

14

15

NUMERICAL DESIGNATIONS AND RESULTANT DISPLAYS

a f e d g b c

SEGMENT IDENTIFICATION

SN74LS247 (TOP VIEW)

OUTPUTS VCC 16 f 15 g 14 f g a 13 b 12 c 11 d 10 e 9

a b c d e

BI/ B C LT RBORBI D A

1 B

2 C

INPUTS

3 4 LAMP RB TEST OUT PUT

5 RB IN PUT

6 D

7 A

8 GND

INPUTS

CIRCUIT FEATURES LAMP INTENSITY MODULATION CAPABILITY

DRIVER OUTPUTS TYPE SN74LS247 ACTIVE LEVEL low OUTPUT CONFIGURATION open-collector SINK CURRENT 24 mA MAX VOLTAGE 15 V TYPICAL POWER DISSIPATION 35 mW

http://onsemi.com
176

SN74LS247
LOGIC DIAGRAM LS247
(13) INPUT (7) A INPUT (1) B INPUT (2) C INPUT (6) D BI/RBO BLANKING (4) INPUT OR RIPPLE-BLANKING OUTPUT (3) (14) (12) OUTPUT a

OUTPUT b OUTPUT c OUTPUT d OUTPUT e OUTPUT f OUTPUT g

(11)

(10)

(9)

(15)

LAMP TEST INPUT RBI (5) RIPPLE-BLANKING INPUT

http://onsemi.com
177

SN74LS247
LS247 FUNCTION TABLE
DECIMAL OR FUNCTION 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 BI RBI LT INPUTS LT H H H H H H H H H H H H H H H H X H L RBI H X X X X X X X X X X X X X X X X L X D L L L L L L L L H H H H H H H H X L X C L L L L H H H H L L L L H H H H X L X B L L H H L L H H L L H H L L H H X L X A L H L H L H L H L H L H L H L H X L X H H H H H H H H H H H H H H H H L L H BI/RBO a ON OFF ON ON OFF ON ON ON ON ON OFF OFF OFF ON OFF OFF OFF OFF ON b ON ON ON ON ON OFF OFF ON ON ON OFF OFF ON OFF OFF OFF OFF OFF ON c ON ON OFF ON ON ON ON ON ON ON OFF ON OFF OFF OFF OFF OFF OFF ON OUTPUTS d ON OFF ON ON OFF ON ON OFF ON ON ON ON OFF ON ON OFF OFF OFF ON e ON OFF ON OFF OFF OFF ON OFF ON OFF ON OFF OFF OFF ON OFF OFF OFF ON f ON OFF OFF OFF ON ON ON OFF ON ON OFF OFF ON ON ON OFF OFF OFF ON g OFF OFF ON ON ON ON ON OFF ON ON ON ON ON ON ON OFF OFF OFF ON 2 3 4 NOTE

H = HIGH Level, L = LOW Level, X = Irrelevant NOTES: 1. The blanking input (BI) must be open or held at a high logic level when output functions 0 through 15 are desired. The ripple-blanking input (RBI) must be open or high if blanking of a decimal zero is not desired. 2. When a low logic level is applied directly to the blanking input (BI), all segment outputs are off regardless of the level of any other input. 3. When ripple-blanking input (RBI) and inputs A, B, C, and D are at a low level with the lamp test input high, all segment outputs go off and the ripple-blanking output (RBO) goes to a low level (response condition). 4. When the blanking input/ripple blanking output (BI/RBO) is open or held high and a low is applied to the lamp-test input, all segment outputs are on. BI/RBO is wire-AND logic serving as blanking input (BI) and/or ripple-blanking output (RBO).

http://onsemi.com
178

SN74LS247
DC CHARACTERISTICS OVER OPERATING TEMPERATURE RANGE (unless otherwise specified)
Limits Symbol VIH VIL VIK VOH Parameter Input HIGH Voltage Input LOW Voltage Input Clamp Diode Voltage Output HIGH Voltage BI / RBO Output LOW Voltage g BI / RBO Off-State Output Current ag On-State Output Voltage g ag Input HIGH Current 0.1 Input LOW Current Any Input, except BI / RBO BI / RBO IOS ICC Short Circuit Current BI / RBO (Note 1) Power Supply Current 0.3 7.0 0.4 1.2 2.0 13 mA mA VCC = MAX VCC = MAX 0.25 0.35 2.4 0.65 4.2 0.25 0.35 0.4 0.5 250 0.4 0.5 20 IIH Min 2.0 0.8 1.5 Typ Max Unit V V V V V V A V V A mA Test Conditions Guaranteed Input HIGH Voltage for All Inputs Guaranteed Input LOW Voltage for All Inputs VCC = MIN, IIN = 18 mA VCC = MIN, IOH = MAX, VIN = VIH or VIL per Truth Table IOL = 1.6 mA IOL = 3.2 mA VCC = VCC MIN, VIN = VIL or VIH per Truth Table

VO OL

IO(off) VO( ) O(on)

VCC = MAX, VIH = 2.0 V, VO(off) = 15 V, VIL = MAX IO(on) = 12 mA IO(on) = 24 mA VCC = MIN, VIH = 2.0 V, VIL per Truth Table

VCC = MAX, VIN = 2.7 V VCC = MAX, VIN = 7.0 V VCC = MAX, VIN = 0.4 V

IIL

mA

Note 1: Not more than one output should be shorted at a time, nor for more than 1 second.

AC CHARACTERISTICS (VCC = 5.0 V, TA = 25C)

Limits Symbol tPLH tPHL tPHL tPLH Parameter Turn-Off Time from A Input Turn-On Time from A Input Turn-Off Time from RBI Input Turn-On Time from RBI Input Min Typ Max 100 100 100 100 Unit ns ns CL = 15 pF, RL = 665 Test Conditions

http://onsemi.com
179

SN74LS251 8-Input Multiplexer with 3-State Outputs

The TTL/MSI SN74LS251 is a high speed 8-Input Digital Multiplexer. It provides, in one package, the ability to select one bit of data from up to eight sources. The LS251 can be used as a universal function generator to generate any logic function of four variables. Both assertion and negation outputs are provided.
http://onsemi.com

Schottky Process for High Speed Multifunction Capability On-Chip Select Logic Decoding Inverting and Non-Inverting 3-State Outputs Input Clamp Diodes Limit High Speed Termination Effects

LOW POWER SCHOTTKY

GUARANTEED OPERATING RANGES

Symbol VCC TA IOH IOL Parameter Supply Voltage Operating Ambient Temperature Range Output Current High Output Current Low Min 4.75 0 Typ 5.0 25 Max 5.25 70 2.6 24 Unit V C mA mA
16 1

PLASTIC N SUFFIX CASE 648

16 1

SOIC D SUFFIX CASE 751B

ORDERING INFORMATION
Device SN74LS251N SN74LS251D Package 16 Pin DIP 16 Pin Shipping 2000 Units/Box 2500/Tape & Reel

Semiconductor Components Industries, LLC, 1999

180

December, 1999 Rev. 6

Publication Order Number: SN74LS251/D

SN74LS251
CONNECTION DIAGRAM DIP (TOP VIEW)
VCC 16 I4 15 I5 14 I6 13 I7 12 S0 11 S1 10 S2 9

1 I3

2 I2

3 I1

4 I0

5 Z

6 Z

7 E0

8 GND

LOADING (Note a) PIN NAMES S0 S2 E0 I0 I7 Z Z Select Inputs Output Enable (Active LOW) Inputs Multiplexer Inputs Multiplexer Output Complementary Multiplexer Output HIGH 0.5 U.L. 0.5 U.L. 0.5 U.L. 65 U.L. 65 U.L. LOW 0.25 U.L. 0.25 U.L. 0.25 U.L. 15 U.L. 15 U.L.

NOTES: a) 1 TTL Unit Load (U.L.) = 40 mA HIGH/1.6 mA LOW.

LOGIC DIAGRAM
I0 S2 S1 S0 E1
9 10 11 7 4

I1
3

I2
2

I3
1

I4
15

I5
14

I6
13

I7
12

VCC = PIN 16 GND = PIN 8 = PIN NUMBERS Z

http://onsemi.com
181

SN74LS251
FUNCTIONAL DESCRIPTION

The LS251 is a logical implementation of a single pole, 8-position switch with the switch position controlled by the state of three Select inputs, S0, S1, S2. Both assertion and negation outputs are provided. The Output Enable input (EO) is active LOW. When it is activated, the logic function provided at the output is:
Z = EO (I0 S0 S1 S2 + I1 S0 S1 S2 + I2 S0 S1 Z = E O S 2 + I 3 S 0 S 1 S 2 + I4 S 0 S 1 S 2 + I5 S 0 Z = EO S1 S2 + I6 S0 S1 S2 + I7 S0 S1 S2).

When the Output Enable is HIGH, both outputs are in the high impedance (high Z) state. This feature allows multiplexer expansion by tying the outputs of up to 128 devices together. When the outputs of the 3-state devices are tied together, all but one device must be in the high impedance state to avoid high currents that would exceed the maximum ratings. The Output Enable signals should be designed to ensure there is no overlap in the active LOW portion of the enable voltage.

TRUTH TABLE
E0 H L L L L L L L L L L L L L L L L S2 X L L L L L L L L H H H H H H H H S1 X L L L L H H H H L L L L H H H H S0 X L L H H L L H H L L H H L L H H I0 X L H X X X X X X X X X X X X X X I1 X X X L H X X X X X X X X X X X X I2 X X X X X L H X X X X X X X X X X I3 X X X X X X X L H X X X X X X X X I4 X X X X X X X X X L H X X X X X X I5 X X X X X X X X X X X L H X X X X I6 X X X X X X X X X X X X X L H X X I7 X X X X X X X X X X X X X X X L H Z (Z) H L H L H L H L H L H L H L H L Z (Z) L H L H L H L H L H L H L H L H

H = HIGH Voltage Level L = LOW Voltage Level X = Dont Care (Z) = High impedance (Off)

http://onsemi.com
182

SN74LS251
DC CHARACTERISTICS OVER OPERATING TEMPERATURE RANGE (unless otherwise specified)
Limits Symbol VIH VIL VIK VOH Parameter Input HIGH Voltage Input LOW Voltage Input Clamp Diode Voltage Output HIGH Voltage 2.4 0.65 3.1 0.25 VO OL IOZH IOZL IIH IIL IOS ICC Output LOW Voltage 0.35 Output Off Current HIGH Output Off Current LOW Input HIGH Current 0.1 Input LOW Current Short Circuit Current (Note 1) Power Supply Current 12 mA 30 0.4 130 10 0.5 20 20 20 V A A A mA mA mA mA IOL = 24 mA 0.4 Min 2.0 0.8 1.5 Typ Max Unit V V V V V Test Conditions Guaranteed Input HIGH Voltage for All Inputs Guaranteed Input LOW Voltage for All Inputs VCC = MIN, IIN = 18 mA VCC = MIN, IOH = MAX, VIN = VIH or VIL per Truth Table IOL = 12 mA VCC = VCC MIN, VIN = VIL or VIH per Truth Table

VCC = MAX, VOUT = 2.7 V VCC = MAX, VOUT = 0.4 V VCC = MAX, VIN = 2.7 V VCC = MAX, VIN = 7.0 V VCC = MAX, VIN = 0.4 V VCC = MAX VCC = MAX, VE = 0 V VCC = MAX, VE = 4.5 V

Note 1: Not more than one output should be shorted at a time, nor for more than 1 second.

AC CHARACTERISTICS (TA = 25C, VCC = 5.0 V)

Limits Symbol tPLH tPHL tPLH tPHL tPLH tPHL tPLH tPHL tPZH tPZL tPZH tPZL tPHZ tPLZ tPHZ tPLZ Parameter Propagation Delay, Select to Z Output Propagation Delay, Select to Z Output Propagation Delay, Data to Z Output Propagation Delay, Data to Z Output Output Enable Time to Z Output Output Enable Time to Z Output Output Disable Time to Z Output Output Disable Time to Z Output Min Typ 20 21 29 28 10 9.0 17 18 17 24 30 26 37 15 30 15 Max 33 33 45 45 15 15 28 28 27 40 45 40 55 25 45 25 Unit ns ns ns ns ns ns ns ns Figure 1 Figure 2 Figure 1 Figures 2 Figures 4, 5 Figures 3, 5 Figures 3, 5 Figures 4, 5 CL = 5.0 pF, RL = 667 k CL = 15 pF, RL = 2.0 k Test Conditions

http://onsemi.com
183

SN74LS251
3-STATE AC WAVEFORMS

VIN

1.3 V tPLH

1.3 V tPHL 1.3 V

VIN

1.3 V tPHL

1.3 V tPLH 1.3 V

VOUT

1.3 V

VOUT

1.3 V

Figure 1.

Figure 2.

VE tPZL VOUT

1.3 V

1.3 V tPLZ

VE tPZH 1.3 V VOL VOUT

1.3 V tPHZ 1.3 V

1.3 V VOH 1.3 V 0.5 V

1.3 V 0.5 V

Figure 3.
0.5 V

Figure 4.

AC LOAD CIRCUIT
VCC

SWITCH POSITIONS
RL SYMBOL tPZH tPZL tPLZ tPHZ SW1 Open Closed Closed Closed SW2 Closed Open Closed Closed

SW1

TO OUTPUT UNDER TEST

5 k CL* SW2

* Includes Jig and Probe Capacitance.

Figure 5.

http://onsemi.com
184

SN74LS253 Dual 4-Input Multiplexer with 3-State Outputs

The LSTTL / MSI SN74LS253 is a Dual 4-Input Multiplexer with 3-state outputs. It can select two bits of data from four sources using common select inputs. The outputs may be individually switched to a high impedance state with a HIGH on the respective Output Enable (E0) inputs, allowing the outputs to interface directly with bus oriented systems. It is fabricated with the Schottky barrier diode process for high speed and is completely compatible with all ON Semiconductor TTL families.
http://onsemi.com

Schottky Process for High Speed Multifunction Capability Non-Inverting 3-State Outputs Input Clamp Diodes Limit High Speed Termination Effects

LOW POWER SCHOTTKY

GUARANTEED OPERATING RANGES

Symbol VCC TA IOH IOL Parameter Supply Voltage Operating Ambient Temperature Range Output Current High Output Current Low Min 4.75 0 Typ 5.0 25 Max 5.25 70 2.6 24 Unit V C mA mA
16 1

PLASTIC N SUFFIX CASE 648

16 1

SOIC D SUFFIX CASE 751B

ORDERING INFORMATION
Device SN74LS253N SN74LS253D Package 16 Pin DIP 16 Pin Shipping 2000 Units/Box 2500/Tape & Reel

Semiconductor Components Industries, LLC, 1999

185

December, 1999 Rev. 6

Publication Order Number: SN74LS253/D

SN74LS253
CONNECTION DIAGRAM DIP (TOP VIEW)
VCC 16 E0b 15 S0 14 I3b 13 I2b 12 I1b 11 I0b 10 Zb 9 NOTE: The Flatpak version has the same pinouts (Connection Diagram) as the Dual In-Line Package. 1 E0a 2 S1 3 I3a 4 I2a 5 I1a 6 I0a 7 Za 8 GND

LOADING (Note a) PIN NAMES S0, S1 Multiplexer A E0a I0a I3a Za Multiplexer B E0b I0b I3b Zb Common Select Inputs Output Enable (Active LOW) Input Multiplexer Inputs Multiplexer Output Output Enable (Active LOW) Input Multiplexer Inputs Multiplexer Output HIGH 0.5 U.L. 0.5 U.L. 0.5 U.L. 65 U.L. 0.5 U.L. 0.5 U.L. 65 U.L. LOW 0.25 U.L. 0.25 U.L. 0.25 U.L. 15 U.L. 0.25 U.L. 0.25 U.L. 15 U.L.

NOTES: a) 1 TTL Unit Load (U.L.) = 40 mA HIGH/1.6 mA LOW.

LOGIC SYMBOL
1 6 5 4 3 10 11 12 13 15

14 2

E I I I I I I I I E S0 0a 0a 1a 2a 3a 0b 1b 2b 3b 0b S1 Za Zb

7 VCC = PIN 16 GND = PIN 8

http://onsemi.com
186

SN74LS253
LOGIC DIAGRAM
E0b
15

I3b
13

I2b
12

I1b
11

I0b
10

S0
14

S1
2

I3a
3

I2a
4

I1a
5

I0a
6

E0a
1

Zb

VCC = PIN 16 GND = PIN 8 = PIN NUMBERS

Za

FUNCTIONAL DESCRIPTION

The LS253 contains two identical 4-Input Multiplexers with 3-state outputs. They select two bits from four sources selected by common select inputs (S0, S1). The 4-input multiplexers have individual Output Enable (E0a, E0b) inputs which when HIGH, forces the outputs to a high impedance (high Z) state. The LS253 is the logic implementation of a 2-pole, 4-position switch, where the position of the switch is determined by the logic levels supplied to the two select inputs. The logic equations for the outputs are shown below:
Za = E0a (I0a S1 S0 + I1a S1 S0 I2a S1 S0 + I3a S1 S0) Zb = E0b (I0b S1 S0 + I1b S1 S0 I2b S1 S0 + I3b S1 S0)

If the outputs of 3-state devices are tied together, all but one device must be in the high impedance state to avoid high currents that would exceed the maximum ratings. Designers should ensure that Output Enable signals to 3-state devices whose outputs are tied together are designed so that there is no overlap.

TRUTH TABLE
SELECT INPUTS S0 X L L H H L L H H S1 X L L L L H H H H I0 X L H X X X X X X DATA INPUTS I1 X X X L H X X X X I2 X X X X X L H X X I3 X X X X X X X L H OUTPUT ENABLE E0 H L L L L L L L L OUTPUT Z (Z) L H L H L H L H

H = HIGH Level L = LOW Level X = Irrelevant (Z) = High Impedance (off) Address inputs S0 and S1 are common to both sections.

http://onsemi.com
187

SN74LS253
DC CHARACTERISTICS OVER OPERATING TEMPERATURE RANGE (unless otherwise specified)
Limits Symbol VIH VIL VIK VOH Parameter Input HIGH Voltage Input LOW Voltage Input Clamp Diode Voltage Output HIGH Voltage 2.4 0.65 3.1 0.25 VO OL IOZH IOZL IIH IIL IOS ICC Output LOW Voltage 0.35 Output Off Current HIGH Output Off Current LOW Input HIGH Current 0.1 Input LOW Current Short Circuit Current (Note 1) Power Supply Current 14 mA 30 0.4 130 12 0.5 20 20 20 V A A A mA mA mA mA IOL = 24 mA 0.4 Min 2.0 0.8 1.5 Typ Max Unit V V V V V Test Conditions Guaranteed Input HIGH Voltage for All Inputs Guaranteed Input LOW Voltage for All Inputs VCC = MIN, IIN = 18 mA VCC = MIN, IOH = MAX, VIN = VIH or VIL per Truth Table IOL = 12 mA VCC = VCC MIN, VIN = VIL or VIH per Truth Table

VCC = MAX, VOUT = 2.7 V VCC = MAX, VOUT = 0.4 V VCC = MAX, VIN = 2.7 V VCC = MAX, VIN = 7.0 V VCC = MAX, VIN = 0.4 V VCC = MAX VCC = MAX, VE = 0 V VCC = MAX, VE = 4.5 V

Note 1: Not more than one output should be shorted at a time, nor for more than 1 second.

AC CHARACTERISTICS (TA = 25C, VCC = 5.0 V) See SN74LS251 for Waveforms

Limits Symbol tPLH tPHL tPLH tPHL tPZH tPZL tPHZ tPLZ Parameter Propagation Delay, Data to Output Propagation Delay, Select to Output Output Enable Time Output Disable Time Min Typ 17 13 30 21 15 15 27 18 Max 25 20 45 32 28 23 41 27 Unit ns ns ns ns Figure 1 Figure 1 Figures 4, 5 Figures 3, 5 CL = 5.0 pF, RL = 667 CL = 45 pF, RL = 667 Test Conditions

http://onsemi.com
188

SN74LS257B SN74LS258B Quad 2-Input Multiplexer with 3-State Outputs

The LSTTL / MSI SN74LS257B and the SN74LS258B are Quad 2-Input Multiplexers with 3-state outputs. Four bits of data from two sources can be selected using a Common Data Select input. The four outputs present the selected data in true (non-inverted) form. The outputs may be switched to a high impedance state with a HIGH on the common Output Enable (EO) Input, allowing the outputs to interface directly with bus oriented systems. It is fabricated with the Schottky barrier diode process for high speed and is completely compatible with all ON Semiconductor TTL families.
http://onsemi.com

LOW POWER SCHOTTKY

Schottky Process For High Speed Multiplexer Expansion By Tying Outputs Together Non-Inverting 3-State Outputs Input Clamp Diodes Limit High Speed Termination Effects Special Circuitry Ensures Glitch Free Multiplexing ESD > 3500 Volts

16 1

GUARANTEED OPERATING RANGES

Symbol VCC TA IOH IOL Parameter Supply Voltage Operating Ambient Temperature Range Output Current High Output Current Low Min 4.75 0 Typ 5.0 25 Max 5.25 70 2.6 24 Unit V C mA mA
16

PLASTIC N SUFFIX CASE 648

SOIC D SUFFIX CASE 751B

ORDERING INFORMATION
Device SN74LS257BN SN74LS257BD SN74LS258BN SN74LS258BD Package 16 Pin DIP 16 Pin 16 Pin DIP 16 Pin Shipping 2000 Units/Box 2500/Tape & Reel 2000 Units/Box 2500/Tape & Reel

Semiconductor Components Industries, LLC, 1999

189

December, 1999 Rev. 6

Publication Order Number: SN74LS257B/D

SN74LS257B SN74LS258B
CONNECTION DIAGRAM DIP (TOP VIEW)
VCC 16 E0 15 I0c 14 I1c 13 Zc 12 I0d 11 I1d 10 Zd 9

SN74LS257B

VCC = PIN 16 GND = PIN 8

1 S VCC 16

2 I0a E0 15

3 I1a I0c 14

4 Za I1c 13

5 I0b Zc 12

6 I1b I0d 11

7 Zb I1d 10

8 GND Zd 9 NOTE: The Flatpak version has the same pinouts (Connection Diagram) as the Dual In-Line Package.

SN74LS258B

1 S

2 I0a

3 I1a

4 Za

5 I0b

6 I1b

7 Zb

8 GND

http://onsemi.com
190

SN74LS257B SN74LS258B
LOGIC DIAGRAMS SN74LS257B
E0
15

I0a
2

I1a
3

I0b
5

I1b
6

I0c
14

I1c
13

I0d
11

I1d
10

S
1

12

Za

Zb

Zc

Zd

SN74LS258B
E0
15

I0a
2

I1a
3

I0b
5

I1b
6

I0c
14

I1c
13

I0d
11

I1d
10

S
1

VCC = PIN 16 GND = PIN 8 = PIN NUMBERS

12

Za

Zb

Zc

Zd

http://onsemi.com
191

SN74LS257B SN74LS258B
FUNCTIONAL DESCRIPTION

The LS257B and LS258B are Quad 2-Input Multiplexers with 3-state outputs. They select four bits of data from two sources each under control of a Common Data Select Input. When the Select Input is LOW, the I0 inputs are selected and when Select is HIGH, the I1 inputs are selected. The data on the selected inputs appears at the outputs in true (non-inverted) form for the LS257B and in the inverted form for the LS258B. The LS257B and LS258B are the logic implementation of a 4-pole, 2-position switch where the position of the switch is determined by the logic levels supplied to the Select Input. The logic equations for the outputs are shown below:
LS257B Za = E 0 Zc = E0 (I1a S + I0a S) Zb = E0 (I1b S + I0b S) (I1c S + I0c S) Zd = E0 (I1d S + I0d S)

When the Output Enable Input (E0) is HIGH, the outputs are forced to a high impedance off state. If the outputs are tied together, all but one device must be in the high impedance state to avoid high currents that would exceed the maximum ratings. Designers should ensure that Output Enable signals to 3-state devices whose outputs are tied together are designed so there is no overlap.

LS258B Za = E 0 Zc = E0

(I1a S + I0a S) Zb = E0 (I1c S + I0c S) Zd = E0

(I1b S + I0b S) (I1d S + I0d S)

TRUTH TABLE
OUTPUT ENABLE EO H L L L L SELECT INPUT S X H H L L DATA INPUTS I0 X X X L H I1 X L H X X OUTPUTS LS257B Z (Z) L H L H OUTPUTS LS258B Z (Z) H L H L

H = HIGH Voltage Level L = LOW Voltage Level X = Dont Care (Z) = High Impedance (off)

http://onsemi.com
192

SN74LS257B SN74LS258B
DC CHARACTERISTICS OVER OPERATING TEMPERATURE RANGE (unless otherwise specified)
Limits Symbol VIH VIL VIK VOH Parameter Input HIGH Voltage Input LOW Voltage Input Clamp Diode Voltage Output HIGH Voltage 2.4 0.65 3.1 0.25 VO OL IOZH IOZL Output LOW Voltage 0.35 Output Off Current HIGH Output Off Current LOW Input HIGH Current Other Inputs S Inputs Other Inputs S Inputs IIL IOS Input LOW Current All Inputs Short Circuit Current (Note 1) Power Supply Current Total, Output HIGH ICC Total, Output LOW Total, Output 3-State LS257B LS258B LS257B LS258B LS257B LS258B 10 9.0 16 14 19 16 mA VCC = MAX 30 0.5 20 20 20 40 0.1 0.2 0.4 130 V A A A IOL = 24 mA 0.4 Min 2.0 0.8 1.5 Typ Max Unit V V V V V Test Conditions Guaranteed Input HIGH Voltage for All Inputs Guaranteed Input LOW Voltage for All Inputs VCC = MIN, IIN = 18 mA VCC = MIN, IOH = MAX, VIN = VIH or VIL per Truth Table IOL = 12 mA VCC = VCC MIN, VIN = VIL or VIH per Truth Table

VCC = MAX, VOUT = 2.7 V VCC = MAX, VOUT = 0.4 V VCC = MAX, VIN = 2.7 V

IIH

mA mA mA

VCC = MAX, VIN = 7.0 V VCC = MAX, VIN = 0.4 V VCC = MAX

mA mA

Note 1: Not more than one output should be shorted at a time, nor for more than 1 second.

AC CHARACTERISTICS (TA = 25C, VCC = 5.0 V) See SN74LS251 for Waveforms

Limits Symbol tPLH tPHL tPLH tPHL tPZH tPZL tPLZ tPHZ Parameter Propagation Delay, Data to Output Propagation Delay, Select to Output Output Enable Time to HIGH Level Output Enable Time to LOW Level Output Disable Time to LOW Level Output Disable Time from HIGH Level Min Typ 10 12 14 14 20 20 16 18 Max 13 15 21 21 25 25 25 25 Unit ns ns ns ns ns ns Test Conditions Figures 1 & 2 CL = 45 pF Figures 1 & 2 Figures 4 & 5 Figures 3 & 5 Figures 3 & 5 Figures 4 & 5 CL = 45 pF RL = 667 CL = 5.0 pF RL = 667

http://onsemi.com
193

SN74LS259 8-Bit Addressable Latch

The SN74LS259 is a high-speed 8-Bit Addressable Latch designed for general purpose storage applications in digital systems. It is a multifunctional device capable of storing single line data in eight addressable latches, and also a 1-of-8 decoder and demultiplexer with active HIGH outputs. The device also incorporates an active LOW common Clear for resetting all latches, as well as, an active LOW Enable.

http://onsemi.com

Serial-to-Parallel Conversion Eight Bits of Storage With Output of Each Bit Available Random (Addressable) Data Entry Active High Demultiplexing or Decoding Capability Easily Expandable Common Clear

LOW POWER SCHOTTKY

GUARANTEED OPERATING RANGES

Symbol VCC TA IOH IOL Parameter Supply Voltage Operating Ambient Temperature Range Output Current High Output Current Low Min 4.75 0 Typ 5.0 25 Max 5.25 70 0.4 8.0 Unit V C mA mA
16 1

PLASTIC N SUFFIX CASE 648

16 1

SOIC D SUFFIX CASE 751B

ORDERING INFORMATION
Device SN74LS259N SN74LS259D Package 16 Pin DIP 16 Pin Shipping 2000 Units/Box 2500/Tape & Reel

Semiconductor Components Industries, LLC, 1999

194

December, 1999 Rev. 6

Publication Order Number: SN74LS259/D

SN74LS259
CONNECTION DIAGRAM DIP (TOP VIEW)
VCC 16 C 15 E 14 D 13 Q7 12 Q6 11 Q5 10 Q4 9

1 Ao

2 A1

3 A2

4 Q0

5 Q1

6 Q2

7 Q3

8 GND

LOADING (Note a) PIN NAMES A0, A1, A2 D E C Q0 Q7 Address Inputs Data Input Enable (Active LOW) Input Clear (Active LOW) Input Parallel Latch Outputs HIGH 0.5 U.L. 0.5 U.L. 1.0 U.L. 0.5 U.L. 10 U.L. LOW 0.25 U.L. 0.25 U.L. 0.5 U.L. 0.25 U.L. 5 U.L.

NOTES: a) 1 TTL Unit Load (U.L.) = 40 mA HIGH/1.6 mA LOW.

http://onsemi.com
195

SN74LS259
LOGIC DIAGRAM
E
14

D
13 1

A0
2

A1

A2
3 15

C VCC = PIN 16 GND = PIN 8 = PIN NUMBERS

10

11

12

Q0

Q1

Q2

Q3

Q4

Q5

Q6

Q7

FUNCTIONAL DESCRIPTION

The SN74LS259 has four modes of operation as shown in the mode selection table. In the addressable latch mode, data on the Data line (D) is written into the addressed latch.The addressed latch will follow the data input with all non-addressed latches remaining in their previous states. In the memory mode, all latches remain in their previous state and are unaffected by the Data or Address inputs. In the one-of-eight decoding or demultiplexing mode, the addressed output will follow the state of the D input with all
MODE SELECTION
E L H L H C H H L L MODE Addressable Latch Memory Active HIGH Eight-Channel Demultiplexer Clear C E D A0 L L L L L L H L L L L L X L H L H H X L L H H A1 X L L L L H X L L L L H H A2 X L L L L Q0 L L H L L

other inputs in the LOW state. In the clear mode all outputs are LOW and unaffected by the address and data inputs. When operating the SN74LS259 as an addressable latch, changing more then one bit of the address could impose a transient wrong address. Therefore, this should only be done while in the memory mode. The truth table below summarizes the operations.

TRUTH TABLE PRESENT OUTPUT STATES

Q1 L L L L H Q2 L L L L L Q3 L L L L L L Q4 L L L L L Q5 L L L L L Q6 L L L L L Q7 L L L L L MODE Clear Demultiplex

H X L L H H

H X L L L L

L QN1 L H QN1 QN1

H Memory

H H X H H H H H H I L L L L L I H L H L H

QN1 QN1 L H

QN1 QN1 QN1 QN1

QN1

Addressable Latch

X = Dont Care Condition L = LOW Voltage Level H = HIGH Voltage Level QN1 = Previous Output State

QN1 QN1 L H

H H

H H

QN1 QN1

http://onsemi.com
196

SN74LS259
DC CHARACTERISTICS OVER OPERATING TEMPERATURE RANGE (unless otherwise specified)
Limits Symbol VIH VIL VIK VOH Parameter Input HIGH Voltage Input LOW Voltage Input Clamp Diode Voltage Output HIGH Voltage 2.7 0.65 3.5 0.25 VO OL Output LOW Voltage 0.35 IIH IIL IOS ICC Input HIGH Current 0.1 Input LOW Current Short Circuit Current (Note 1) Power Supply Current 20 0.4 100 36 0.5 20 V A mA mA mA mA IOL = 8.0 mA 0.4 Min 2.0 0.8 1.5 Typ Max Unit V V V V V Test Conditions Guaranteed Input HIGH Voltage for All Inputs Guaranteed Input LOW Voltage for All Inputs VCC = MIN, IIN = 18 mA VCC = MIN, IOH = MAX, VIN = VIH or VIL per Truth Table IOL = 4.0 mA VCC = VCC MIN, VIN = VIL or VIH per Truth Table

VCC = MAX, VIN = 2.7 V VCC = MAX, VIN = 7.0 V VCC = MAX, VIN = 0.4 V VCC = MAX VCC = MAX

Note 1: Not more than one output should be shorted at a time, nor for more than 1 second.

AC CHARACTERISTICS (TA = 25C, VCC = 5.0 V)

Limits Symbol tPLH tPHL tPLH tPHL tPLH tPHL tPHL Parameter Turn-Off Delay, Enable to Output Turn-On Delay, Enable to Output Turn-Off Delay, Data to Output Turn-On Delay, Data to Output Turn-Off Delay, Address to Output Turn-On Delay, Address to Output Turn-On Delay, Clear to Output Min Typ 22 15 20 13 24 18 17 Max 35 24 32 21 38 29 27 Unit ns ns ns ns ns ns ns Test Conditions

CL = 15 pF

AC SET-UP REQUIREMENTS (TA = 25C, VCC = 5.0 V)

Limits Symbol ts tW th th Input Setup Time Pulse Width, Clear or Enable Hold Time, Data Hold Time, Address Parameter Min 20 15 5.0 20 Typ Max Unit ns ns ns ns

http://onsemi.com
197

SN74LS259
AC WAVEFORMS
D D tw E tPHL Q OTHER CONDITIONS: C = H, A = STABLE tPLH 1.3 V OTHER CONDITIONS: E = L, C = H, A = STABLE tw 1.3 V Q 1.3 V tPHL 1.3 V 1.3 V tPLH 1.3 V

Figure 2. Turn-on and Turn-off Delays, Data to Output

Figure 1. Turn-on and Turn-off Delays, Enable To Output and Enable Pulse Width

A1

1.3 V

1.3 V

D ts(H) th(H) ts(L) th(L) 1.3 V

A1 Q1

1.3 V tPHL 1.3 V

1.3 V tPLH 1.3 V

Q=D

Q=D

OTHER CONDITIONS: E = L, C = L, D = H

OTHER CONDITIONS: C = H, A = STABLE

Figure 3. Turn-on and Turn-off Delays, Address to Output

Figure 4. Setup and Hold Time, Data to Enable

1.3 V tPHL

A ts E

STABLE ADDRESS

Q OTHER CONDITIONS: E = H

1.3 V

Figure 5. Turn-on Delay, Clear to Output

OTHER CONDITIONS: C = H

Figure 6. Setup Time, Address to Enable (See Notes 1 and 2)

NOTES: 1. The Address to Enable Setup Time is the time before the HIGH-to-LOW Enable transition that the Address must be stable so that the correct latch is addressed and the other latches are not affected. 2. The shaded areas indicate when the inputs are permitted to change for predictable output performance.

http://onsemi.com
198

SN74LS260 Dual 5-Input NOR Gate

VCC 14 13 12 11 10 9 8

http://onsemi.com

7 GND

LOW POWER SCHOTTKY

GUARANTEED OPERATING RANGES

Symbol VCC TA IOH IOL Parameter Supply Voltage Operating Ambient Temperature Range Output Current High Output Current Low Min 4.75 0 Typ 5.0 25 Max 5.25 70 0.4 8.0 Unit V C mA mA
14 1

PLASTIC N SUFFIX CASE 646

14 1

SOIC D SUFFIX CASE 751A

ORDERING INFORMATION
Device SN74LS260N SN74LS260D Package 14 Pin DIP 14 Pin Shipping 2000 Units/Box 2500/Tape & Reel

Semiconductor Components Industries, LLC, 1999

199

December, 1999 Rev. 6

Publication Order Number: SN74LS260/D

SN74LS260
DC CHARACTERISTICS OVER OPERATING TEMPERATURE RANGE (unless otherwise specified)
Limits Symbol VIH VIL VIK VOH Parameter Input HIGH Voltage Input LOW Voltage Input Clamp Diode Voltage Output HIGH Voltage 2.7 0.65 3.5 0.25 VO OL Output LOW Voltage 0.35 IIH IIL IOS ICC Input HIGH Current 0.1 Input LOW Current Short Circuit Current (Note 1) Power Supply Current Total, Output HIGH Total, Output LOW 20 0.4 100 4.0 5.5 0.5 20 V A mA mA mA IOL = 8.0 mA 0.4 Min 2.0 0.8 1.5 Typ Max Unit V V V V V Test Conditions Guaranteed Input HIGH Voltage for All Inputs Guaranteed Input LOW Voltage for All Inputs VCC = MIN, IIN = 18 mA VCC = MIN, IOH = MAX, VIN = VIH or VIL per Truth Table IOL = 4.0 mA VCC = VCC MIN, VIN = VIL or VIH per Truth Table

VCC = MAX, VIN = 2.7 V VCC = MAX, VIN = 7.0 V VCC = MAX, VIN = 0.4 V VCC = MAX VCC = MAX

mA

Note 1: Not more than one output should be shorted at a time, nor for more than 1 second.

AC CHARACTERISTICS (TA = 25C)

Limits Symbol tPLH tPHL Parameter Turn-Off Delay, Input to Output Turn-On Delay, Input to Output Min Typ 5.0 6.0 Max 15 15 Unit ns ns Test Conditions VCC = 5.0 V CL = 15 pF

http://onsemi.com
200

SN74LS273 Octal D Flip-Flop with Clear

The SN74LS273 is a high-speed 8-Bit Register. The register consists of eight D-Type Flip-Flops with a Common Clock and an asynchronous active LOW Master Reset. This device is supplied in a 20-pin package featuring 0.3 inch lead spacing.
http://onsemi.com

8-Bit High Speed Register Parallel Register Common Clock and Master Reset Input Clamp Diodes Limit High-Speed Termination Effects

LOW POWER SCHOTTKY

GUARANTEED OPERATING RANGES

Symbol VCC TA IOH IOL Parameter Supply Voltage Operating Ambient Temperature Range Output Current High Output Current Low Min 4.75 0 Typ 5.0 25 Max 5.25 70 0.4 8.0 Unit V C
20

mA mA

PLASTIC N SUFFIX CASE 738

20 1

SOIC DW SUFFIX CASE 751D

ORDERING INFORMATION
Device SN74LS273N SN74LS273DW Package 16 Pin DIP 16 Pin Shipping 1440 Units/Box 2500/Tape & Reel

Semiconductor Components Industries, LLC, 1999

201

December, 1999 Rev. 6

Publication Order Number: SN74LS273/D

SN74LS273
CONNECTION DIAGRAM DIP (TOP VIEW)
VCC 20 Q7 19 D7 18 D6 17 Q6 16 Q5 15 D5 14 D4 13 Q4 12 CP 11

1 MR

2 Q0

3 D0

4 D1

5 Q1

6 Q2

7 D2

8 D3

9 Q3

10 GND

LOADING (Note a) PIN NAMES CP D0 D7 MR Q0 Q7 Clock (Active HIGH Going Edge) Input Data Inputs Master Reset (Active LOW) Input Register Outputs HIGH 0.5 U.L. 0.5 U.L. 0.5 U.L. 10 U.L. LOW 0.25 U.L. 0.25 U.L. 0.25 U.L. 5 U.L.

NOTES: a) 1 TTL Unit Load (U.L.) = 40 mA HIGH/1.6 mA LOW.

TRUTH TABLE
MR L H H CP X Dx X H L Qx L H L

H = HIGH Logic Level L = LOW Logic Level X = Immaterial

LOGIC DIAGRAM
3 11 4 7 8 13 14 17 18

D0

D1

D2

D3

D4

D5

D6

D7

CP CP D CD Q CP D CD Q CP D CD Q CP D CD Q CP D CD Q CP D CD Q CP D CD Q CP D CD Q

MR

VCC = PIN 20 GND = PIN 10 = PIN NUMBERS

Q0
2

Q1
5

Q2
6

Q3
9

Q4
12

Q5
15

Q6
16

Q7
19

http://onsemi.com
202

SN74LS273
FUNCTIONAL DESCRIPTION

The SN74LS273 is an 8-Bit Parallel Register with a common Clock and common Master Reset. When the MR input is LOW, the Q outputs are LOW, independent of the other inputs. Information meeting the

setup and hold time requirements of the D inputs is transferred to the Q outputs on the LOW-to-HIGH transition of the clock input.

DC CHARACTERISTICS OVER OPERATING TEMPERATURE RANGE (unless otherwise specified)

Limits Symbol VIH VIL VIK VOH Parameter Input HIGH Voltage Input LOW Voltage Input Clamp Diode Voltage Output HIGH Voltage 2.7 0.65 3.5 0.25 VO OL Output LOW Voltage 0.35 IIH IIL IOS ICC Input HIGH Current 0.1 Input LOW Current Short Circuit Current (Note 1) Power Supply Current 20 0.4 100 27 0.5 20 V A mA mA mA mA IOL = 8.0 mA 0.4 Min 2.0 0.8 1.5 Typ Max Unit V V V V V Test Conditions Guaranteed Input HIGH Voltage for All Inputs Guaranteed Input LOW Voltage for All Inputs VCC = MIN, IIN = 18 mA VCC = MIN, IOH = MAX, VIN = VIH or VIL per Truth Table IOL = 4.0 mA VCC = VCC MIN, VIN = VIL or VIH per Truth Table

VCC = MAX, VIN = 2.7 V VCC = MAX, VIN = 7.0 V VCC = MAX, VIN = 0.4 V VCC = MAX VCC = MAX

Note 1: Not more than one output should be shorted at a time, nor for more than 1 second.

AC CHARACTERISTICS (TA = 25C, VCC = 5.0 V)

Limits Symbol fMAX tPHL tPLH tPHL Parameter Maximum Input Clock Frequency Propagation Delay, MR to Q Output Propagation Delay, Clock to Output Min 30 Typ 40 18 17 18 27 27 27 Max Unit MHz ns ns Test Conditions Figure 1 Figure 2 Figure 1

AC SETUP REQUIREMENTS (TA = 25C, VCC = 5.0 V)

Limits Symbol tw ts th trec Parameter Pulse Width, Clock or Clear Data Setup Time Hold Time Recovery Time Min 20 20 5.0 25 Typ Max Unit ns ns ns ns Test Conditions Figure 1 Figure 1 Figure 1 Figure 2

http://onsemi.com
203

SN74LS273
AC WAVEFORMS
1/f max tW CP 1.3 V ts(H) D * 1.3 V tPLH Qn 1.3 V tPHL
*The shaded areas indicate when the input is permitted to *change for predictable output performance.

MR 1.3 V th(L) 1.3 V 1.3 V tPHL 1.3 V tPLH Qn CP

tW 1.3 V trec 1.3 V tPHL 1.3 V tPLH 1.3 V 1.3 V 1.3 V

1.3 V th(H)

1.3 V ts(L)

Qn

Figure 1. Clock to Output Delays, Clock Pulse Width, Frequency, Setup and Hold Times Data to Clock DEFINITION OF TERMS

Figure 2. Master Reset to Output Delay, Master Reset Pulse Width, and Master Reset Recovery Time

SETUP TIME (ts) is defined as the minimum time required for the correct logic level to be present at the logic input prior to the clock transition from LOW-to-HIGH in order to be recognized and transferred to the outputs. HOLD TIME (th) is defined as the minimum time following the clock transition from LOW-to-HIGH that the logic level must be maintained at the input in order to ensure

continued recognition. A negative HOLD TIME indicates that the correct logic level may be released prior to the clock transition from LOW-to-HIGH and still be recognized. RECOVERY TIME (trec) is defined as the minimum time required between the end of the reset pulse and the clock transition from LOW-to-HIGH in order to recognize and transfer HIGH data to the Q outputs.

http://onsemi.com
204

SN74LS280 9-Bit Odd/Even Parity Generators/Checkers

The SN74LS280 is a Universal 9-Bit Parity Generator / Checker. It features odd / even outputs to facilitate either odd or even parity. By cascading, the word length is easily expanded. The LS280 is designed without the expander input implementation, but the corresponding function is provided by an input at Pin 4 and the absence of any connection at Pin 3. This design permits the LS280 to be substituted for the LS180 which results in improved performance. The LS280 has buffered inputs to lower the drive requirements to one LS unit load.
http://onsemi.com

LOW POWER SCHOTTKY

Generates Either Odd or Even Parity for Nine Data Lines Typical Data-to-Output Delay of only 33 ns Cascadable for n-Bits Can Be Used To Upgrade Systems Using MSI Parity Circuits Typical Power Dissipation = 80 mW
14 1

INPUTS VCC 14 F 13 F G H 1 G 2 H 3 NC I E 12 E D 11 D C 10 C B 9 B A 8

PLASTIC N SUFFIX CASE 646

A EVEN ODD

14 1

4 5 6 7 I GND INPUT EVEN ODD OUTPUTS

INPUTS

SOIC D SUFFIX CASE 751A

FUNCTION TABLE
NUMBER OF INPUTS A THRU 1 THAT ARE HIGH 0, 2, 4, 6, 8 1, 3, 5, 7, 9
H = HIGH Level, L = LOW Level

OUTPUTS EVEN H L ODD L H

ORDERING INFORMATION
Device SN74LS280N Package 14 Pin DIP 14 Pin Shipping 2000 Units/Box 2500/Tape & Reel

GUARANTEED OPERATING RANGES

Symbol VCC TA IOH IOL Parameter Supply Voltage Operating Ambient Temperature Range Output Current High Output Current Low Min 4.75 0 Typ 5.0 25 Max 5.25 70 0.4 8.0 Unit V C mA mA

SN74LS280D

Semiconductor Components Industries, LLC, 1999

205

December, 1999 Rev. 6

Publication Order Number: SN74LS280/D

SN74LS280
FUNCTIONAL BLOCK DIAGRAM
A (8) B (9) (5) EVEN

C (10)

D E F

(11) (12) (13) (6) ODD

G H

(1) (2)

I (4)

DC CHARACTERISTICS OVER OPERATING TEMPERATURE RANGE (unless otherwise specified)

Limits Symbol VIH VIL VIK VOH Parameter Input HIGH Voltage Input LOW Voltage Input Clamp Diode Voltage Output HIGH Voltage 2.7 0.65 3.5 0.25 VO OL Output LOW Voltage 0.35 IIH IIL IOS ICC Input HIGH Current 0.1 Input LOW Current Short Circuit Current (Note 1) Power Supply Current 20 0.4 100 27 0.5 20 V A mA mA mA mA IOL = 8.0 mA 0.4 Min 2.0 0.8 1.5 Typ Max Unit V V V V V Test Conditions Guaranteed Input HIGH Voltage for All Inputs Guaranteed Input LOW Voltage for All Inputs VCC = MIN, IIN = 18 mA VCC = MIN, IOH = MAX, VIN = VIH or VIL per Truth Table IOL = 4.0 mA VCC = VCC MIN, VIN = VIL or VIH per Truth Table

VCC = MAX, VIN = 2.7 V VCC = MAX, VIN = 7.0 V VCC = MAX, VIN = 0.4 V VCC = MAX VCC = MAX

Note 1: Not more than one output should be shorted at a time, nor for more than 1 second.

AC CHARACTERISTICS (TA = 25C, VCC = 5.0 V)

Limits Symbol tPLH tPHL tPLH tPHL Parameter Propagation Delay, Data to Output EVEN Propagation Delay, Data to Output ODD Min Typ 33 29 23 31 Max 50 45 35 50 Unit ns CL = 15 pF ns Test Conditions

http://onsemi.com
206

SN74LS283 4-Bit Binary Full Adder with Fast Carry

The SN74LS283 is a high-speed 4-Bit Binary Full Adder with internal carry lookahead. It accepts two 4-bit binary words (A1 A4, B1 B4) and a Carry Input (C0). It generates the binary Sum outputs (1 4) and the Carry Output (C4) from the most significant bit. The LS283 operates with either active HIGH or active LOW operands (positive or negative logic).
GUARANTEED OPERATING RANGES
Symbol VCC TA IOH IOL Parameter Supply Voltage Operating Ambient Temperature Range Output Current High Output Current Low Min 4.75 0 Typ 5.0 25 Max 5.25 70 0.4 8.0 Unit V C mA mA
16 1

http://onsemi.com

LOW POWER SCHOTTKY

PLASTIC N SUFFIX CASE 648

16 1

SOIC D SUFFIX CASE 751B

ORDERING INFORMATION
Device SN74LS283N SN74LS283D Package 16 Pin DIP 16 Pin Shipping 2000 Units/Box 2500/Tape & Reel

Semiconductor Components Industries, LLC, 1999

207

December, 1999 Rev. 6

Publication Order Number: SN74LS283/D

SN74LS283
CONNECTION DIAGRAM DIP (TOP VIEW)
VCC 16 B3 15 A3 14 3 13 A4 12 B4 11 4 10 C4 9 NOTE: The Flatpak version has the same pinouts (Connection Diagram) as the Dual In-Line Package. 1 2 2 B2 3 A2 4 1 5 A1 6 B1 7 C0 8 GND

LOADING (Note a) PIN NAMES A1 A4 B1 B4 C0 S1 S4 C4 Operand A Inputs Operand B Inputs Carry Input Sum Outputs Carry Output HIGH 1.0 U.L. 1.0 U.L. 0.5 U.L. 10 U.L. 10 U.L. LOW 0.5 U.L. 0.5 U.L. 0.25 U.L. 5 U.L. 5 U.L.

NOTES: a) 1 TTL Unit Load (U.L.) = 40 mA HIGH/1.6 mA LOW.

LOGIC SYMBOL
5 3 14 12 6 2 15 11

A1 A2 A3 A4 B1 B2 B3 B4 7 C0 1 2 3 4 4 1 13 10 C4 9

VCC = PIN 16 GND = PIN 8

http://onsemi.com
208

SN74LS283
LOGIC DIAGRAM
C0
7

A1
5

B1
6

A2
3

B2
2

A3
14

B3
15

A4
12

B4
11

C1

C2

C3

4 1 VCC = PIN 16 GND = PIN 8 = PIN NUMBERS 2

1 3

13 4

10

C4

FUNCTIONAL DESCRIPTION

The LS283 adds two 4-bit binary words (A plus B) plus the incoming carry. The binary sum appears on the sum outputs (1 4) and outgoing carry (C4) outputs.
C0 + (A1 + B1) + 2(A2 + B2) + 4(A3 + B3) + 8(A4 + B4) = 1 + 2 2 + 4 3 + 8 4 + 16C4

Where: (+) = plus

Example:
C0 logic levels Active HIGH Active LOW L 0 1 A1 L 0 1 A2 H 1 0 A3 L 0 1 A4 H 1 0 B1 H 1 0

Due to the symmetry of the binary add function the LS283 can be used with either all inputs and outputs active HIGH (positive logic) or with all inputs and outputs active LOW (negative logic). Note that with active HIGH inputs, Carry Input can not be left open, but must be held LOW when no carry in is intended.

B2 L 0 1

B3 L 0 1

B4 H 1 0

1 H 1 0

2 H 1 0

3 L 0 1

4 L 0 1

C4 H 1 0 (10+9=19) (carry+5+6=12)

Interchanging inputs of equal weight does not affect the operation, thus C0, A1, B1, can be arbitrarily assigned to pins 7, 5 or 3.

http://onsemi.com
209

SN74LS283
FUNCTIONAL TRUTH TABLE
C (n 1) L L L L H H H H An L L H H L L H H Bn L H L H L H L H n L H H L H L L H Cn L L L H L H H H

C1 C3 are generated internally C0 is an external input C4 is an output generated internally

DC CHARACTERISTICS OVER OPERATING TEMPERATURE RANGE (unless otherwise specified)

Limits Symbol VIH VIL VIK VOH Parameter Input HIGH Voltage Input LOW Voltage Input Clamp Diode Voltage Output HIGH Voltage 2.7 0.65 3.5 0.25 VO OL Output LOW Voltage 0.35 C0 Any A or B IIH Input HIGH Current C0 Any A or B IIL IOS ICC Input LOW Current C0 Any A or B Short Circuit Current (Note 1) Power Supply Current Total, Output HIGH Total, Output LOW 20 0.1 0.2 0.4 0.8 100 34 39 0.5 20 40 V A A mA mA mA mA mA VCC = MAX, VIN = 0 4 V MAX 0.4 VCC = MAX VCC = MAX VCC = MAX, VIN = 7 0 V MAX 7.0 IOL = 8.0 mA 0.4 Min 2.0 0.8 1.5 Typ Max Unit V V V V V Test Conditions Guaranteed Input HIGH Voltage for All Inputs Guaranteed Input LOW Voltage for All Inputs VCC = MIN, IIN = 18 mA VCC = MIN, IOH = MAX, VIN = VIH or VIL per Truth Table IOL = 4.0 mA VCC = VCC MIN, VIN = VIL or VIH per Truth Table

VCC = MAX, VIN = 2 7 V MAX 2.7

mA

Note 1: Not more than one output should be shorted at a time, nor for more than 1 second.

http://onsemi.com
210

SN74LS283
AC CHARACTERISTICS (TA = 25C, VCC = 5.0 V)
Limits Symbol tPLH tPHL tPLH tPHL tPLH tPHL tPLH tPHL Parameter Propagation Delay, C0 Input to Any Output Propagation Delay, Any A or B Input to Outputs Propagation Delay, C0 Input to C4 Output Propagation Delay, Any A or B Input to C4 Output Min Typ 16 15 15 15 11 11 11 12 Max 24 24 24 24 17 22 17 17 Unit ns ns CL = 15 pF Figures 1 & 2 ns ns Test Conditions

AC WAVEFORMS
1.3 V tPLH 1.3 V VOUT tPHL

VIN VOUT

1.3 V tPHL 1.3 V tPLH

VIN

Figure 1.

Figure 2.

http://onsemi.com
211

SN74LS298 Quad 2-Input Multiplexer with Storage

The SN74LS298 is a Quad 2-Port Register. It is the logical equivalent of a quad 2-input multiplexer followed by a quad 4-bit edge-triggered register. A Common Select input selects between two 4-bit input ports (data sources.) The selected data is transferred to the output register synchronous with the HIGH to LOW transition of the Clock input. The LS298 is fabricated with the Schottky barrier process for high speed and is completely compatible with all ON Semiconductor TTL families.
http://onsemi.com

LOW POWER SCHOTTKY

Select From Two Data Sources Fully Edge-Triggered Operation Typical Power Dissipation of 65 mW Input Clamp Diodes Limit High Speed Termination Effects
16

GUARANTEED OPERATING RANGES

Symbol VCC TA IOH IOL Parameter Supply Voltage Operating Ambient Temperature Range Output Current High Output Current Low Min 4.75 0 Typ 5.0 25 Max 5.25 70 0.4 8.0 Unit V C mA mA

PLASTIC N SUFFIX CASE 648

16 1

SOIC D SUFFIX CASE 751B

ORDERING INFORMATION
Device SN74LS298N SN74LS298D Package 16 Pin DIP 16 Pin Shipping 2000 Units/Box 2500/Tape & Reel

Semiconductor Components Industries, LLC, 1999

212

December, 1999 Rev. 6

Publication Order Number: SN74LS298/D

SN74LS298
CONNECTION DIAGRAM DIP (TOP VIEW)
VCC 16 Qa 15 Qb 14 Qc 13 Qd 12 CP 11 S 10 I0c 9 NOTE: The Flatpak version has the same pinouts (Connection Diagram) as the Dual In-Line Package. 1 I1b 2 I1a 3 I0a 4 I0b 5 I1c 6 I1d 7 I0d 8 GND

LOADING (Note a) PIN NAMES S CP I0a I0d I1a I1d Qa Qd Common Select Input Clock (Active LOW Going Edge) Input Data Inputs from Source 0 Data Inputs from Source 1 Register Outputs HIGH 0.5 U.L. 0.5 U.L. 0.5 U.L. 0.5 U.L. 10 U.L. LOW 0.25 U.L. 0.25 U.L. 0.25 U.L. 0.25 U.L. 5 U.L.

NOTES: a) 1 TTL Unit Load (U.L.) = 40 mA HIGH/1.6 mA LOW.

LOGIC SYMBOL
3 2 4 1 9 5 7 6

I0a I1a I0b I1b I0c I1c I0d I1d 10 11 S CP Qa 15

Qb 14

Qc 13

Qd 12

VCC = PIN 16 GND = PIN 8

http://onsemi.com
213

SN74LS298
LOGIC OR BLOCK DIAGRAM
I1a
2

I0a
3

I1b
1

I0b
4

I1c
5

I0c
9

I1d
6

I0d
7

S
10

CP

11

R CP S Qa
15

R CP S Qb
14

R CP S Qc
13

R CP S Qd
12

VCC = PIN 16 GND = PIN 8 = PIN NUMBERS

Qa

Qb

Qc

Qd

FUNCTIONAL DESCRIPTION

The LS298 is a high speed Quad 2-Port Register. It selects four bits of data from two sources (ports)under the control of a Common Select Input (S). The selected data is transferred to the 4-bit output register synchronous with the HIGH to LOW transition of the Clock input (CP). The 4-bit

output register is fully edge-triggered. The Data inputs (I) and Select input (S) must be stable only one setup time prior to the HIGH to LOW transition of the clock for predictable operation.

TRUTH TABLE
INPUTS S I I h h I0 I h X X I1 X X I h OUTPUT Q L H L H

L = LOW Voltage Level H = HIGH Voltage Level X = Dont Care I = LOW Voltage Level one setup time prior to the HIGH to LOW clock transition. h = HIGH Voltage Level one setup time prior to the HIGH to LOW clock transition.

http://onsemi.com
214

SN74LS298
DC CHARACTERISTICS OVER OPERATING TEMPERATURE RANGE (unless otherwise specified)
Limits Symbol VIH VIL VIK VOH Parameter Input HIGH Voltage Input LOW Voltage Input Clamp Diode Voltage Output HIGH Voltage 2.7 0.65 3.5 0.25 VO OL Output LOW Voltage 0.35 IIH IIL IOS ICC Input HIGH Current 0.1 Input LOW Current Short Circuit Current (Note 1) Power Supply Current 20 0.4 100 21 0.5 20 V A mA mA mA mA IOL = 8.0 mA 0.4 Min 2.0 0.8 1.5 Typ Max Unit V V V V V Test Conditions Guaranteed Input HIGH Voltage for All Inputs Guaranteed Input LOW Voltage for All Inputs VCC = MIN, IIN = 18 mA VCC = MIN, IOH = MAX, VIN = VIH or VIL per Truth Table IOL = 4.0 mA VCC = VCC MIN, VIN = VIL or VIH per Truth Table

VCC = MAX, VIN = 2.7 V VCC = MAX, VIN = 7.0 V VCC = MAX, VIN = 0.4 V VCC = MAX VCC = MAX

Note 1: Not more than one output should be shorted at a time, nor for more than 1 second.

AC CHARACTERISTICS (TA = 25C, VCC = 5.0 V)

Limits Symbol tPLH tPHL Parameter Propagation Delay, g y Clock to Output Min Typ 18 21 Max 27 32 Unit ns ns Test Conditions VCC = 5.0 V, CL = 15 pF

AC SET-UP REQUIREMENTS (TA = 25C, VCC = 5.0 V)

Limits Symbol tW ts ts th th Parameter Clock Pulse Width Data Setup Time Select Setup Time Data Hold Time Select Hold Time Min 20 15 25 5.0 0 Typ Max Unit ns ns ns ns VCC = 5.0 V Test Conditions

DEFINITIONS OF TERMS

SETUP TIME (ts) is defined as the minimum time required for the correct logic level to be present at the logic input prior to the clock transition from LOW to HIGH in order to be recognized and transferred to the outputs. HOLD TIME (th) is defined as the minimum time following the clock transition from LOW to HIGH that the

logic level must be maintained at the input in order to ensure continued recognition. A negative HOLD TIME indicates that the correct logic level may be released prior to the clock transition from LOW to HIGH and still be recognized.

http://onsemi.com
215

SN74LS298
AC WAVEFORMS
I0 I1* ts(L) CP 1.3 V tPHL Q 1.3 V tW(H) tPLH 1.3 V Q Q = I0 Q = I1 1.3 V th(L) tW(L) ts(H) 1.3 V 1.3 V th(H) ts(L) CP 1.3 V S* 1.3 V th(L) = 0 1.3 V th(H) = 0 ts(H) 1.3 V

*The shaded areas indicate when the input is permitted to *change for predictable output performance.

Figure 1.

Figure 2.

http://onsemi.com
216

SN74LS299 8-Bit Shift/Storage Register with 3-State Outputs

The SN74LS299 is an 8-Bit Universal Shift / Storage Register with 3-state outputs. Four modes of operation are possible: hold (store), shift left, shift right and load data. The parallel load inputs and flip-flop outputs are multiplexed to reduce the total number of package pins. Separate outputs are provided for flip-flops Q0 and Q7 to allow easy cascading. A separate active LOW Master Reset is used to reset the register.
http://onsemi.com

Common I/O for Reduced Pin Count Four Operation Modes: Shift Left, Shift Right, Load and Store Separate Shift Right Serial Input and Shift Left Serial Input for Easy
Cascading 3-State Outputs for Bus Oriented Applications Input Clamp Diodes Limit High-Speed Termination Effects ESD > 3500 Volts
20

LOW POWER SCHOTTKY

GUARANTEED OPERATING RANGES

Symbol VCC TA IOH IOL IOH IOL Parameter Supply Voltage Operating Ambient Temperature Range Output Current High Q 0 , Q7 Output Current Low Q 0 , Q7 Output Current High I/O0 1/O7 Output Current Low I/O0 1/O7 Min 4.75 0 Typ 5.0 25 Max 5.25 70 0.4 8.0 2.6 24 Unit V C mA mA mA mA

PLASTIC N SUFFIX CASE 738

20 1

SOIC DW SUFFIX CASE 751D

ORDERING INFORMATION
Device SN74LS299N SN74LS299DW Package 16 Pin DIP 16 Pin Shipping 1440 Units/Box 2500/Tape & Reel

Semiconductor Components Industries, LLC, 1999

217

December, 1999 Rev. 6

Publication Order Number: SN74LS299/D

SN74LS299
CONNECTION DIAGRAM DIP (TOP VIEW)
VCC 20 S1 19 Ds7 18 Q7 17 I/O7 I/O5 I/O3 I/O1 16 15 14 13 CP 12 DS0 11 NOTE: The Flatpak version has the same pinouts (Connection Diagram) as the Dual In-Line Package.

1 S0

2 3 4 OE1 OE2 I/O6

8 5 6 7 I/O4 I/O2 I/O0 Q0

9 10 MR GND

LOADING (Note a) PIN NAMES CP DS0 DS7 I/On OE1, OE2 Q0, Q7 MR S0, S1 Clock Pulse (Active PositiveGoing Edge) Input Serial Data Input for Right Shift Serial Data Input for Left Shift Parallel Data Input or Parallel Output (3State) 3State Output Enable (Active LOW) Inputs Serial Outputs Asynchronous Master Reset (Active LOW) Input Mode Select Inputs HIGH 0.5 U.L. 0.5 U.L. 0.5 U.L. 0.5 U.L. 65 U.L. 0.5 U.L. 10 U.L. 0.5 U.L. 1 U.L. LOW 0.25 U.L. 0.25 U.L. 0.25 U.L. 0.25 U.L. 15 U.L. 0.25 U.L. 5 U.L. 0.25 U.L. 0.5 U.L.

NOTES: a) 1 TTL Unit Load (U.L.) = 40 mA HIGH/1.6 mA LOW.

S1 19 S0

LOGIC DIAGRAM

18

DS7 DS0
11

12

CLOCK Q0 MR OE1 OE2

8 9 2 3

D CK CLR Q

D CK CLR Q

D CK CLR Q

D CK CLR Q

D CK CLR Q

D CK CLR Q

D CK CLR Q

D CK CLR Q

17

Q7 VCC = PIN 20 GND = PIN 10 = PIN NUMBERS

13

14

15

16

I/O0

I/O1

I/O2

I/O3

I/O4

I/O5

I/O6

I/O7

http://onsemi.com
218

SN74LS299
FUNCTION TABLE
INPUTS MR L L L L L H H H H H H H H S1 X X H L X L L H H H L L L S0 X X H X L H H L L H L L L OE1 H X X L L X L X L X H X L OE2 X H X L L X L X L X X H L X X X CP X X X X X DS0 X X X X X D D X X X X X X DS7 X X X X X X X D D X X X X Asynchronous Reset; Q0 = Q7 = LOW Reset I/O Voltage Undetermined Asynchronous Reset; Q0 = Q7 = LOW I/O Voltage LOW RESPONSE

Shift Left; DQ7; Q7Q6; etc. Shift Left; DQ7 & I/O7; Q7Q6 & I/O6; etc. Parallel Load; I/OnQn
Hold: I/O Voltage undetermined Hold: I/On = Qn

Shift Right; D Q0; Q0 Q1; etc. Shift Right; D Q0 & I/O0; Q0 O1 & I/O1; etc.

H = HIGH Voltage Level L = LOW Voltage Level X = Immaterial

http://onsemi.com
219

SN74LS299
DC CHARACTERISTICS OVER OPERATING TEMPERATURE RANGE (unless otherwise specified)
Limits Symbol VIH VIL VIK VOH VOH Parameter Input HIGH Voltage Input LOW Voltage Input Clamp Diode Voltage Output HIGH Voltage I/O0 I/O7 Output HIGH Voltage Q 0 , Q7 Output LOW Voltage g I/O0 I/O7 Output LOW Voltage g I/O0 I/O7 Output Off Current HIGH I/O0 I/O7 Output Off Current LOW I/O0 I/O7 Others S0, S1, I/O0 I/O7 IIH Input HIGH C I t Current t Others S0, S1 I/O0 I/O7 Others IIL IOS Input LOW Current S0, S1 Short Circuit Current (Note 1) Power Supply Current Q 0 , Q7 I/O0 I/O7 20 30 0.8 100 130 53 mA mA mA mA 2.4 2.7 0.65 3.1 3.4 0.25 0.35 0.4 0.5 0.4 0.5 40 400 20 40 0.1 0.2 0.1 0.4 Min 2.0 0.8 1.5 Typ Max Unit V V V V V V V V V A A A A mA mA mA mA VCC = MAX, VIN = 0 4 V MAX 0.4 VCC = MAX VCC = MAX VCC = MAX VCC = MAX, VIN = 7 0 V MAX 7.0 VCC = MAX, VIN = 5.5 V VCC = MAX, VIN = 2.7 V Test Conditions Guaranteed Input HIGH Voltage for All Inputs Guaranteed Input LOW Voltage for All Inputs VCC = MIN, IIN = 18 mA VCC = MIN, IOH = MAX VCC = MIN, IOH = MAX IOL = 12 mA IOL = 24 mA IOL = 4.0 mA IOL = 8.0 mA VCC = VCC MIN, VIN = VIL or VIH per Truth Table VCC = VCC MIN, VIN = VIL or VIH per Truth Table

VO OL

VO OL IOZH IOZL

VCC = MAX, VOUT = 2.7 V VCC = MAX, VOUT = 0.4 V

ICC

Note 1: Not more than one output should be shorted at a time, nor for more than 1 second.

http://onsemi.com
220

SN74LS299
AC CHARACTERISTICS (TA = 25C, VCC = 5.0 V)
Limits Symbol fMAX tPHL tPLH tPHL tPHL tPLH tPHL tPZH tPZL tPHZ tPLZ Parameter Maximum Clock Frequency Propagation Delay, Clock to Q0 or Q7 Propagation Delay, Clear to Q0 or Q7 Propagation Delay, Clock to I/O0 I/O7 Propagation Delay, Clear to I/O0 I/O7 Output Enable Time Output Disable Time Min 25 Typ 35 26 22 27 26 17 26 13 19 10 10 39 33 40 39 25 40 21 30 15 15 Max Unit MHz ns ns ns ns ns ns CL = 5.0 pF CL = 45 pF, RL = 667 CL = 15 pF Test Conditions

AC SETUP REQUIREMENTS (TA = 25C, VCC = 5.0 V)

Limits Symbol tW tW tW ts ts th th trec Parameter Clock Pulse Width HIGH Clock Pulse Width LOW Clear Pulse Width LOW Data Setup Time Select Setup Time Data Hold Time Select Hold Time Recovery Time Min 25 13 20 20 35 0 10 20 Typ Max Unit ns ns ns ns ns ns ns ns VCC = 5 0 V 5.0 Test Conditions

http://onsemi.com
221

SN74LS299
3-STATE WAVEFORMS

VIN

1.3 V tPLH

1.3 V tPHL 1.3 V

VIN

1.3 V tPLH

1.3 V tPHL 1.3 V

VOUT

1.3 V

VOUT

1.3 V

Figure 1.

Figure 2.

VE 1.5 V VE VOUT tPZL 1.5 V 0.5 V 1.5 V tPLZ 1.5 V VOL

VE 1.5 V VE tPZH 1.5 V VOUT tPHZ 1.5 V VOH 1.5 V 0.5 V

Figure 3.

Figure 4.

AC LOAD CIRCUIT SWITCH POSITIONS

VCC RL SYMBOL tPZH tPZL tPLZ tPHZ SW1 Open Closed Closed Closed SW2 Closed Open Closed Closed

SW1

TO OUTPUT UNDER TEST

5 k CL* SW2

* Includes Jig and Probe Capacitance.

Figure 5.

http://onsemi.com
222

SN74LS365A SN74LS367A SN74LS368A 3-State Hex Buffers

These devices are high speed hex buffers with 3-state outputs. They are organized as single 6-bit or 2-bit / 4-bit, with inverting or non-inverting data (D) paths. The outputs are designed to drive 15 TTL Unit Loads or 60 Low Power Schottky loads when the Enable (E) is LOW. When the Output Enable (E) is HIGH, the outputs are forced to a high impedance off state. If the outputs of the 3-state devices are tied together, all but one device must be in the high impedance state to avoid high currents that would exceed the maximum ratings. Designers should ensure that Output Enable signals to 3-state devices whose outputs are tied together are designed so there is no overlap.
GUARANTEED OPERATING RANGES
Symbol VCC TA IOH IOL Parameter Supply Voltage Operating Ambient Temperature Range Output Current High Output Current Low Min 4.75 0 Typ 5.0 25 Max 5.25 70 2.6 24 Unit V C mA mA
16 1

http://onsemi.com

LOW POWER SCHOTTKY

PLASTIC N SUFFIX CASE 648

16 1

SOIC D SUFFIX CASE 751B

ORDERING INFORMATION
Device SN74LS365AN SN74LS365AD SN74LS367AN SN74LS367AD SN74LS368AN SN74LS368AD Package 16 Pin DIP 16 Pin 16 Pin DIP 16 Pin 16 Pin DIP 16 Pin Shipping 2000 Units/Box 2500/Tape & Reel 2000 Units/Box 2500/Tape & Reel 2000 Units/Box 2500/Tape & Reel

Semiconductor Components Industries, LLC, 1999

223

December, 1999 Rev. 6

Publication Order Number: SN74LS365A/D

SN74LS365A SN74LS367A SN74LS368A

SN74LS365A HEX 3-STATE BUFFER WITH COMMON 2-INPUT NOR ENABLE
VCC 16 E2 15 14 13 12 11 10 9

1 E1

8 GND

TRUTH TABLE
INPUTS E1 L L H X E2 L L X H D L H X X L H (Z) (Z) OUTPUT

SN74LS367A HEX 3-STATE BUFFER SEPARATE 2-BIT AND 4-BIT SECTIONS

VCC 16 E 15 14 13 12 11 10 9

SN74LS368A HEX 3-STATE INVERTER BUFFER SEPARATE 2-BIT AND 4-BIT SECTIONS
VCC 16 E 15 14 13 12 11 10 9

1 E

8 GND

1 E

8 GND

TRUTH TABLE
INPUTS E L L H D L H X L H (Z) OUTPUT

TRUTH TABLE
INPUTS E L L H D L H X H L (Z) OUTPUT

http://onsemi.com
224

SN74LS365A SN74LS367A SN74LS368A

DC CHARACTERISTICS OVER OPERATING TEMPERATURE RANGE (unless otherwise specified)
Limits Symbol VIH VIL VIK VOH Parameter Input HIGH Voltage Input LOW Voltage Input Clamp Diode Voltage Output HIGH Voltage 2.4 0.65 3.1 0.25 VO OL IOZH IOZL IIH Output LOW Voltage 0.35 Output Off Current HIGH Output Off Current LOW Input HIGH Current 0.1 Input LOW Current E Inputs IIL D Inputs 0.4 20 0.4 IOS ICC Short Circuit Current (Note 1) Power Supply Current LS365A, 367A LS368A 40 225 24 21 0.5 20 20 20 V A A A mA mA A mA mA IOL = 24 mA 0.4 Min 2.0 0.8 1.5 Typ Max Unit V V V V V Test Conditions Guaranteed Input HIGH Voltage for All Inputs Guaranteed Input LOW Voltage for All Inputs VCC = MIN, IIN = 18 mA VCC = MIN, IOH = MAX, VIN = VIH or VIL per Truth Table IOL = 12 mA VCC = VCC MIN, VIN = VIL or VIH per Truth Table

VCC = MAX, VOUT = 2.7 V VCC = MAX, VOUT = 0.4 V VCC = MAX, VIN = 2.7 V VCC = MAX, VIN = 7.0 V VCC = MAX, VIN = 0.4 V VCC = MAX, VIN = 0.5 V Either E Input at 2.0 V VCC = MAX, VIN = 0.4 V Both E Inputs at 0.4 V VCC = MAX VCC = MAX

mA

Note 1: Not more than one output should be shorted at a time, nor for more than 1 second.

AC CHARACTERISTICS (TA = 25C, VCC = 5.0 V)

Limits LS365A / LS367A Symbol tPLH tPHL tPZH tPZL tPHZ tPLZ Parameter Propagation Delay Output Enable Time Output Disable Time Min Typ 10 9.0 19 24 Max 16 22 35 40 30 35 LS366A / LS368A Min Typ 7.0 12 18 28 Max 15 18 35 45 32 35 Unit ns ns ns CL = 45 pF, RL = 667 Test Conditions

CL = 5.0 pF

http://onsemi.com
225

SN74LS373 SN74LS374 Octal Transparent Latch with 3-State Outputs; Octal D-Type Flip-Flop with 3-State Output
The SN74LS373 consists of eight latches with 3-state outputs for bus organized system applications. The flip-flops appear transparent to the data (data changes asynchronously) when Latch Enable (LE) is HIGH. When LE is LOW, the data that meets the setup times is latched. Data appears on the bus when the Output Enable (OE) is LOW. When OE is HIGH the bus output is in the high impedance state. The SN74LS374 is a high-speed, low-power Octal D-type Flip-Flop featuring separate D-type inputs for each flip-flop and 3-state outputs for bus oriented applications. A buffered Clock (CP) and Output Enable (OE) is common to all flip-flops. The SN74LS374 is manufactured using advanced Low Power Schottky technology and is compatible with all ON Semiconductor TTL families.
http://onsemi.com

LOW POWER SCHOTTKY

Eight Latches in a Single Package 3-State Outputs for Bus Interfacing Hysteresis on Latch Enable Edge-Triggered D-Type Inputs Buffered Positive Edge-Triggered Clock Hysteresis on Clock Input to Improve Noise Margin Input Clamp Diodes Limit High Speed Termination Effects

20 1

PLASTIC N SUFFIX CASE 738

GUARANTEED OPERATING RANGES

Symbol VCC TA IOH IOL Parameter Supply Voltage Operating Ambient Temperature Range Output Current High Output Current Low Min 4.75 0 Typ 5.0 25 Max 5.25 70 2.6 24 Unit V C mA mA

20 1

SOIC DW SUFFIX CASE 751D

ORDERING INFORMATION
Device SN74LS373N SN74LS373DW SN74LS374N SN74LS374DW Package 16 Pin DIP 16 Pin 16 Pin DIP 16 Pin Shipping 1440 Units/Box 2500/Tape & Reel 1440 Units/Box 2500/Tape & Reel

Semiconductor Components Industries, LLC, 1999

226

December, 1999 Rev. 6

Publication Order Number: SN74LS373/D

SN74LS373 SN74LS374
CONNECTION DIAGRAM DIP (TOP VIEW) SN74LS373
VCC 20 O7 19 D7 18 D6 17 O6 16 O5 15 D5 14 D4 13 O4 12 LE 11 VCC 20 O7 19 D7 18 D6 17

SN74LS374
O6 16 O5 15 D5 14 D4 13 O4 12 CP 11

1 OE

2 O0

3 D0

4 D1

5 O1

6 O2

7 D2

8 D3

9 O3

10 GND

NOTE: The Flatpak version has the same pinouts (Connection Diagram) as the Dual In-Line Package.

1 OE

2 O0

3 D0

4 D1

5 O1

6 O2

7 D2

8 D3

9 O3

10 GND

LOADING (Note a) PIN NAMES D0 D7 LE CP OE O0 O7 Data Inputs Latch Enable (Active HIGH) Input Clock (Active HIGH Going Edge) Input Output Enable (Active LOW) Input Outputs HIGH 0.5 U.L. 0.5 U.L. 0.5 U.L. 0.5 U.L. 65 U.L. LOW 0.25 U.L. 0.25 U.L. 0.25 U.L. 0.25 U.L. 15 U.L.

NOTES: a) 1 TTL Unit Load (U.L.) = 40 mA HIGH/1.6 mA LOW.

TRUTH TABLE LS373

Dn H L X X LE H H L X OE L L L H On H L Q0 Z* Dn H L X X

LS374
LE OE L L H On H L Z*

H = HIGH Voltage Level L = LOW Voltage Level X = Immaterial Z = High Impedance * Note: Contents of flip-flops unaffected by the state of the Output Enable input (OE).

http://onsemi.com
227

SN74LS373 SN74LS374
LOGIC DIAGRAMS SN74LS373
3 4 7 8 13 14 17 18

D0 D LATCH ENABLE LE 11 OE Q G

D1 D Q G

D2 D Q G

D3 D Q G

D4 D Q G

D5 D Q G

D6 D Q G

D7 D Q G

VCC = PIN 20 GND = PIN 10 = PIN NUMBERS

O0
2 5

O1
6

O2
9

O3
12

O4
15

O5
16

O6
19

O7

SN74LS374
3 11 4 7 8 13 14 17 18

D0 CP D Q Q CP D Q Q

D1 CP D Q Q

D2 CP D Q Q

D3 CP D Q Q

D4 CP D Q Q

D5 CP D Q Q

D6 CP D Q Q

D7

CP

OE
1 2

O0
5

O1
6

O2
9

O3
12

O4
15

O5
16

O6
19

O7

DC CHARACTERISTICS OVER OPERATING TEMPERATURE RANGE (unless otherwise specified)

Limits Symbol VIH VIL VIK VOH Parameter Input HIGH Voltage Input LOW Voltage Input Clamp Diode Voltage Output HIGH Voltage 2.4 0.65 3.1 0.25 VO OL IOZH IOZL IIH IIL IOS ICC Output LOW Voltage 0.35 Output Off Current HIGH Output Off Current LOW Input HIGH Current Input LOW Current Short Circuit Current (Note 1) Power Supply Current 30 0.5 20 20 20 0.1 0.4 130 40 V A A A mA mA mA mA IOL = 24 mA 0.4 Min 2.0 0.8 1.5 Typ Max Unit V V V V V Test Conditions Guaranteed Input HIGH Voltage for All Inputs Guaranteed Input LOW Voltage for All Inputs VCC = MIN, IIN = 18 mA VCC = MIN, IOH = MAX, VIN = VIH or VIL per Truth Table IOL = 12 mA VCC = VCC MIN, VIN = VIL or VIH per Truth Table

VCC = MAX, VOUT = 2.7 V VCC = MAX, VOUT = 0.4 V VCC = MAX, VIN = 2.7 V VCC = MAX, VIN = 7.0 V VCC = MAX, VIN = 0.4 V VCC = MAX VCC = MAX

Note 1: Not more than one output should be shorted at a time, nor for more than 1 second.

http://onsemi.com
228

SN74LS373 SN74LS374
AC CHARACTERISTICS (TA = 25C, VCC = 5.0 V)
Limits LS373 Symbol fMAX tPLH tPHL tPLH tPHL tPZH tPZL tPHZ tPLZ Parameter Maximum Clock Frequency Propagation Delay, Data to Output Clock or Enable to Output Output Enable Time Output Disable Time 12 12 20 18 15 25 12 15 18 18 30 30 28 36 20 25 15 19 20 21 12 15 28 28 28 28 20 25 Min Typ Max Min 35 LS374 Typ 50 Max Unit MHz ns ns ns ns CL = 5.0 pF CL = 45 pF pF, RL = 667 Test Conditions

AC SETUP REQUIREMENTS (TA = 25C, VCC = 5.0 V)

Limits LS373 Symbol tW ts th Clock Pulse Width Setup Time Hold Time Parameter Min 15 5.0 20 Max Min 15 20 0 LS374 Max Unit ns ns ns

DEFINITION OF TERMS

SETUP TIME (ts) is defined as the minimum time required for the correct logic level to be present at the logic input prior to LE transition from HIGH-to-LOW in order to be recognized and transferred to the outputs.

HOLD TIME (th) is defined as the minimum time following the LE transition from HIGH-to-LOW that the logic level must be maintained at the input in order to ensure continued recognition.

http://onsemi.com
229

SN74LS373 SN74LS374
SN74LS373 AC WAVEFORMS
tW LE 1.3 V ts Dn tPLH OUTPUT tPHL th tW

Figure 1.
OE tPZL VOUT 1.3 V 0.5 V 1.3 V 1.3 V tPLZ 1.3 V VOL OE tPZH VOUT 1.3 V 1.3 V tPHZ 1.3 V VOH 1.3 V 0.5 V

Figure 2.

Figure 3.

AC LOAD CIRCUIT
VCC

SWITCH POSITIONS
RL SYMBOL SW1 tPZH tPZL TO OUTPUT UNDER TEST tPLZ tPHZ SW1 Open Closed Closed Closed SW2 Closed Open Closed Closed

5.0 k CL* SW2

* Includes Jig and Probe Capacitance.

Figure 4.

http://onsemi.com
230

SN74LS373 SN74LS374
SN74LS374 AC WAVEFORMS
tWH CP 1.3 V ts Dn tPLH OUTPUT 1.3 V 1.3 V tPHL 1.3 V tWL 1.3 V 1.3 V th OE tPZL VOUT 1.3 V 0.5 V 1.3 V 1.3 V tPLZ 1.3 V VOL

Figure 6.

Figure 5.

OE tPZH VOUT

1.3 V tPHZ 1.3 V

1.3 V VOH 1.3 V 0.5 V

Figure 7.

AC LOAD CIRCUIT
VCC RL

SWITCH POSITIONS
SYMBOL tPZH SW1 Open Closed Closed Closed SW2 Closed Open Closed Closed

SW1

tPZL tPLZ

TO OUTPUT UNDER TEST

tPHZ

5.0 k CL* SW2

* Includes Jig and Probe Capacitance.

Figure 8.

http://onsemi.com
231

SN74LS377 Octal D Flip-Flop with Enable

The SN74LS377 is an 8-bit register built using advanced Low Power Schottky technology. This register consists of eight D-type flip-flops with a buffered common clock and a buffered common clock enable.
http://onsemi.com

8-Bit High Speed Parallel Registers Positive Edge-Triggered D-Type Flip Flops Fully Buffered Common Clock and Enable Inputs True and Complement Outputs Input Clamp Diodes Limit High Speed Termination Effects

LOW POWER SCHOTTKY

GUARANTEED OPERATING RANGES

Symbol VCC TA IOH IOL Parameter Supply Voltage Operating Ambient Temperature Range Output Current High Output Current Low Min 4.75 0 Typ 5.0 25 Max 5.25 70 0.4 8.0 Unit V C mA mA
20 1

PLASTIC N SUFFIX CASE 738

20 1

SOIC DW SUFFIX CASE 751D

ORDERING INFORMATION
Device SN74LS377N SN74LS377DW Package 16 Pin DIP 16 Pin Shipping 1440 Units/Box 2500/Tape & Reel

Semiconductor Components Industries, LLC, 1999

232

December, 1999 Rev. 6

Publication Order Number: SN74LS377/D

SN74LS377
CONNECTION DIAGRAM DIP (TOP VIEW)

VCC 20

Q7 19

D7 18

D6 17

Q6 16

Q5 15

D5 14

D4 13

Q4 12

CP 11 NOTE: The Flatpak version has the same pinouts (Connection Diagram) as the Dual In-Line Package.

1 E

2 Q0

3 D0

4 D1

5 Q1

6 Q2

7 D2

8 D3

9 Q3

10 GND

LOADING (Note a) PIN NAMES E D0 D3 CP Q0 Q3 Q0 Q3 Enable (Active LOW) Input Data Inputs Clock (Active HIGH Going Edge) Input True Outputs Complemented Outputs HIGH 0.5 U.L. 0.5 U.L. 0.5 U.L. 10 U.L. 10 U.L. LOW 0.25 U.L. 0.25 U.L. 0.25 U.L. 5 U.L. 5 U.L.

NOTES: a) 1 TTL Unit Load (U.L.) = 40 mA HIGH/1.6 mA LOW.

LOGIC DIAGRAM
3 4 7 8 13 14 17 18

D0 E ENABLE
1

D1

D2

D3

D4

D5

D6

D7

CP CLOCK
11

CP D Q

CP D Q

CP D Q

CP D Q

CP D Q

CP D Q

CP D Q

CP D Q

Q0
2

Q1
5

Q2
6

Q3
9

Q4
12

Q5
15

Q6
16

Q7
19

http://onsemi.com
233

SN74LS377
DC CHARACTERISTICS OVER OPERATING TEMPERATURE RANGE (unless otherwise specified)
Limits Symbol VIH VIL VIK VOH Parameter Input HIGH Voltage Input LOW Voltage Input Clamp Diode Voltage Output HIGH Voltage 2.7 0.65 3.5 0.25 VO OL Output LOW Voltage 0.35 Input HIGH Current Input LOW Current Short Circuit Current (Note 1) Power Supply Current 20 0.5 20 0.1 0.4 100 28 V A mA mA mA mA 0.4 Min 2.0 0.8 1.5 Typ Max Unit V V V V V Test Conditions Guaranteed Input HIGH Voltage for All Inputs Guaranteed Input LOW Voltage for All Inputs VCC = MIN, IIN = 18 mA VCC = MIN, IOH = MAX, VIN = VIH or VIL per Truth Table IOL = 4.0 mA IOL = 8.0 mA VCC = VCC MIN, VIN = VIL or VIH per Truth Table

IIH IIL IOS ICC

VCC = MAX, VIN = 2.7 V VCC = MAX, VIN = 7.0 V VCC = MAX, VIN = 0.4 V VCC = MAX VCC = MAX, NOTE 1

NOTE: With all inputs open and GND applied to all data and enable inputs, ICC is measured after a momentary GND, then 4.5 V is applied to clock. Note 1: Not more than one output should be shorted at a time, nor for more than 1 second.

AC CHARACTERISTICS (TA = 25C, VCC = 5.0 V)

Limits Symbol fMAX tPLH tPHL Parameter Maximum Clock Frequency Propagation Delay, Clock to Output Min 30 Typ 40 17 18 27 27 Max Unit MHz ns Test Conditions VCC = 5 0 V 5.0 CL = 15 pF

AC SETUP REQUIREMENTS (TA = 25C, VCC = 5.0 V)

Limits Symbol tW ts ts th Parameter Any Pulse Width Data Setup Time Enable Setup Time Any Hold Time Inactive State Active State Min 20 20 10 25 5.0 Typ Max Unit ns ns ns ns ns VCC = 5.0 V Test Conditions

DEFINITION OF TERMS

SETUP TIME (ts) is defined as the minimum time required for the correct logic level to be present at the logic input prior to the clock transition from LOW-to-HIGH in order to be recognized and transferred to the outputs. HOLD TIME (th) is defined as the minimum time following the clock transition from LOW-to-HIGH that the

logic level must be maintained at the input in order to ensure continued recognition. A negative HOLD TIME indicates that the correct logic level may be released prior to the clock transition from LOW-to-HIGH and still be recognized.

http://onsemi.com
234

SN74LS377
TRUTH TABLE
E H L L
L = LOW Voltage Level H = HIGH Voltage Level X = Immaterial

CP

Dn X H L

Qn No Change H L

Qn No Change L H

AC WAVEFORM
1/fmax CP 1.3 V ts(H) D OR E * 1.3 V tPLH Q 1.3 V th(H) ts(L) tW 1.3 V th(L) 1.3 V tPHL 1.3 V

*The shaded areas indicate when the input is permitted to change for predictable output performance.

http://onsemi.com
235

SN74LS393 Dual 4-Stage Binary Counter

The SN74LS393 contains a pair of high-speed 4-stage ripple counters. Each half of the LS393 operates as a Modulo-16 binary divider, with the last three stages triggered in a ripple fashion. In the LS393, the flip-flops are triggered by a HIGH-to-LOW transition of their CP inputs. Each half of each circuit type has a Master Reset input which responds to a HIGH signal by forcing all four outputs to the LOW state. Dual Versions Individual Asynchronous Clear for Each Counter Typical Max Count Frequency of 50 MHz Input Clamp Diodes Minimize High Speed Termination Effects
GUARANTEED OPERATING RANGES
Symbol VCC TA IOH IOL Parameter Supply Voltage Operating Ambient Temperature Range Output Current High Output Current Low Min 4.75 0 Typ 5.0 25 Max 5.25 70 0.4 8.0 Unit V C mA mA
14 1

http://onsemi.com

LOW POWER SCHOTTKY

PLASTIC N SUFFIX CASE 646

14 1

SOIC D SUFFIX CASE 751A

ORDERING INFORMATION
Device SN74LS393N SN74LS393D Package 14 Pin DIP 14 Pin Shipping 2000 Units/Box 2500/Tape & Reel

Semiconductor Components Industries, LLC, 1999

236

December, 1999 Rev. 0

Publication Order Number: SN74LS393/D

SN74LS393
CONNECTION DIAGRAM DIP (TOP VIEW)
VCC 14 CP 13 MR 12 Q0 11 Q1 10 Q2 9 Q3 8 NOTE: The Flatpak version has the same pinouts (Connection Diagram) as the Dual In-Line Package. 1 CP 2 MR 3 Q0 4 Q1 5 Q2 6 Q3 7 GND

LOADING (Note a) PIN NAMES CP CP0 CP1 MR Q0 Q3 Clock (Active LOW Going Edge) Input to +16 (LS393) Clock (Active LOW Going Edge) Input to 2 (LS390) Clock (Active LOW Going Edge) Input to 5 (LS390) Master Reset (Active HIGH) Input FlipFlop Outputs HIGH 0.5 U.L. 0.5 U.L. 0.5 U.L. 0.5 U.L. 10 U.L. LOW 1.0 U.L. 1.0 U.L. 1.5 U.L. 0.25 U.L. 5 U.L.

NOTES: a) 1 TTL Unit Load (U.L.) = 40 mA HIGH/1.6 mA LOW.

http://onsemi.com
237

SN74LS393
FUNCTIONAL DESCRIPTION

Each half of the SN74LS393 operates in the Modulo 16 binary sequence, as indicated in the 16 Truth Table. The first flip-flop is triggered by HIGH-to-LOW transitions of the CP input signal. Each of the other flip-flops is triggered by a HIGH-to-LOW transition of the Q output of the preceding flip-flop. Thus state changes of the Q outputs do

not occur simultaneously. This means that logic signals derived from combinations of these outputs will be subject to decoding spikes and, therefore, should not be used as clocks for other counters, registers or flip-flops. A HIGH signal on MR forces all outputs to the LOW state and prevents counting.

SN74LS393 LOGIC DIAGRAM (one half shown)

CP

K CP CD MR

J Q CD

K CP

J Q CD

K CP

J Q CD

K CP

J Q

Q0

Q1

Q2

Q3

TRUTH TABLE
OUTPUTS COUNT 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Q3 L L L L L L L L H H H H H H H H Q2 L L L L H H H H L L L L H H H H Q1 L L H H L L H H L L H H L L H H Q0 L H L H L H L H L H L H L H L H

H = HIGH Voltage Level L = LOW Voltage Level

http://onsemi.com
238

SN74LS393
DC CHARACTERISTICS OVER OPERATING TEMPERATURE RANGE (unless otherwise specified)
Limits Symbol VIH VIL VIK VOH Parameter Input HIGH Voltage Input LOW Voltage Input Clamp Diode Voltage Output HIGH Voltage 2.7 0.65 3.5 0.25 VO OL Output LOW Voltage 0.35 IIH Input HIGH Current 0.1 MR IIL Input LOW Current CP, CP0 CP1 IOS ICC Short Circuit Current (Note 1) Power Supply Current 20 0.4 1.6 2.4 100 26 0.5 20 V A mA mA mA mA mA mA VCC = MAX VCC = MAX VCC = MAX, VIN = 0.4 V IOL = 8.0 mA 0.4 Min 2.0 0.8 1.5 Typ Max Unit V V V V V Test Conditions Guaranteed Input HIGH Voltage for All Inputs Guaranteed Input LOW Voltage for All Inputs VCC = MIN, IIN = 18 mA VCC = MIN, IOH = MAX, VIN = VIH or VIL per Truth Table IOL = 4.0 mA VCC = VCC MIN, VIN = VIL or VIH per Truth Table

VCC = MAX, VIN = 2.7 V VCC = MAX, VIN = 7.0 V

Note 1: Not more than one output should be shorted at a time, nor for more than 1 second.

AC CHARACTERISTICS (TA = 25C, VCC = 5.0 V)

Limits Symbol fMAX fMAX tPLH tPHL tPLH tPHL tPHL Parameter Maximum Clock Frequency CP0 to Q0 Maximum Clock Frequency CP1 to Q1 Propagation Delay, CP to Q0 CP to Q3 MR to Any Output Min 25 20 12 13 40 40 24 20 20 60 60 39 Typ 35 Max Unit MHz MHz ns ns ns CL = 15 pF Test Conditions

AC SETUP REQUIREMENTS (TA = 25C, VCC = 5.0 V)

Limits Symbol tW tW trec Parameter Clock Pulse Width MR Pulse Width Recovery Time Min 20 20 25 Typ Max Unit ns ns ns VCC = 5.0 V Test Conditions

http://onsemi.com
239

SN74LS393
AC WAVEFORMS

*CP

1.3 V tW tPHL

1.3 V tPLH 1.3 V 1.3 V

Figure 1.

MR & MS 1.3 V tW CP 1.3 V tPHL Q 1.3 V 1.3 V trec

Figure 2.

*The number of Clock Pulses required between tPHL and tPLH measurements can be determined from the appropriate Truth Table.

http://onsemi.com
240

SN74LS541 Octal Buffer/Line Driver with 3-State Outputs

The SN74LS541 is an octal buffer and line driver with the same functions as the LS241, but with pinouts on the opposite side of the package. This device type is designed to be used as a memory address driver, clock driver and bus-oriented transmitter / receiver. This device is especially useful as output ports for the microprocessors, allowing ease of layout and greater PC board density.
http://onsemi.com

Hysteresis at Inputs to Improve Noise Margin PNP Inputs Reduce Loading 3-State Outputs Drive Bus Lines Inputs and Outputs Opposite Side of Package, Allowing Easier Interface to Microprocessors Input Clamp Diodes Limit High-Speed Termination Effects
LOGIC AND CONNECTION DIAGRAM DIP (TOP VIEW)
VCC 20 19 18 17 16 15 14 13 12 11
20

LOW POWER SCHOTTKY

PLASTIC N SUFFIX CASE 738

10 GND
20 1

GUARANTEED OPERATING RANGES

Symbol VCC TA IOH IOL Parameter Supply Voltage Operating Ambient Temperature Range Output Current High Output Current Low Min 4.75 0 Typ 5.0 25 Max 5.25 70 15 24 Unit V C mA mA

SOIC DW SUFFIX CASE 751D

ORDERING INFORMATION
Device SN74LS541N SN74LS541DW Package 16 Pin DIP 16 Pin Shipping 1440 Units/Box 2500/Tape & Reel

Semiconductor Components Industries, LLC, 1999

241

December, 1999 Rev. 0

Publication Order Number: SN74LS541/D

SN74LS541
BLOCK DIAGRAM
E1 E2 (2) (18) (1) (19)

INPUTS E1 Y1 L H X L E2 L X H L D H X X L

OUTPUTS LS540 L Z Z H LS541 H Z Z L

D1

D2 D3 D4 D5 D6 D7 D8

(3) (4) (5) (6) (7) (8) (9)

(17) (16) (15) (14) (13)

Y2 Y3 Y4 Y5 Y6

L = LOW Voltage Level H = HIGH Voltage Level X = Immaterial Z = High Impedance

(12) Y7 (11) Y8

DC CHARACTERISTICS OVER OPERATING TEMPERATURE RANGE (unless otherwise specified)

Limits Symbol VIH VIL VIK VO OH Parameter Input HIGH Voltage Input LOW Voltage Input Clamp Diode Voltage 2.4 Output HIGH Voltage 2.0 0.25 VO OL VT+VT IOZH IOZL IIH IIL IOS Output LOW Voltage 0.35 Hysteresis Output Off Current HIGH Output Off Current LOW Input HIGH Current 0.1 Input LOW Current Short Circuit Current (Note 1) Power Supply Current Total, Output HIGH ICC Total, Output LOW Total Output 3-State 40 0.2 225 32 52 55 0.2 0.4 20 20 20 0.5 V V A A A mA mA mA mA mA mA VCC = MAX IOL = 24 mA VCC = MIN VCC = MAX, VOUT = 2.7 V VCC = MAX, VOUT = 0.4 V VCC = MAX, VIN = 2.7 V VCC = MAX, VIN = 7.0 V VCC = MAX, VIN = 0.4 V VCC = MAX 0.4 V V 0.65 3.4 Min 2.0 0.8 1.5 Typ Max Unit V V V V Test Conditions Guaranteed Input HIGH Voltage for All Inputs Guaranteed Input LOW Voltage for All Inputs VCC = MIN, IIN = 18 mA VCC = MIN, IOH = 3.0 mA VCC = MIN, IOH = MAX, VIL = 0.5 V IOL = 12 mA VCC = VCC MIN, VIN = VIL or VIH per Truth Table

Note 1: Not more than one output should be shorted at a time, nor for more than 1 second.

http://onsemi.com
242

SN74LS541
AC CHARACTERISTICS (TA = 25C)
Limits Symbol tPLH tPHL tPZH tPZL tPHZ tPLZ Parameter Propagation Delay, g y Data to Output Output Enable Time to HIGH Level Output Enable Time to LOW Level Output Disable Time to HIGH Level Output Disable Time to LOW Level Min Typ 12 12 15 20 10 15 Max 15 ns 18 32 38 18 29 ns ns ns CL = 5 0 pF 5.0 ns VCC = 5 0 V 5.0 CL = 45 pF RL = 667 Unit Test Conditions

AC WAVEFORMS
VCC VIN 1.3 V tPLH VOUT 1.3 V 1.3 V tPHL 1.3 V SW1 RL

Figure 1.
TO OUTPUT UNDER TEST VIN 1.3 V tPLH VOUT 1.3 V 1.3 V tPHL 1.3 V CL* 5 k SW2

Figure 2.
VE VE VOUT

1.5 V tPZL 1.5 V

1.5 V tPLZ 1.5 V VOL 0.5 V

SWITCH POSITIONS
SYMBOL tPZH tPZL tPLZ SW1 Open Closed Closed Closed SW2 Closed Open Closed Closed

Figure 3.
VE 1.5 V VE VOUT tPZH 1.5 V 1.5 V tPHZ VOH 1.5 V 0.5 V

tPHZ

Figure 4.

Figure 5.

http://onsemi.com
243

SN74LS640 SN74LS641 SN74LS642 SN74LS645 Octal Bus Transceivers

These octal bus transceivers are designed for asynchronous two-way communication between data buses. Control function implementation minimizes external timing requirements. These circuits allow data transmission from the A bus to B or from the B bus to A bus depending upon the logic level of the direction control (DIR) input. Enable input (G) can disable the device so that the buses are effectively isolated.
DEVICE LS640 LS641 LS642 LS645 OUTPUT 3-State Open-Collector Open-Collector 3-State LOGIC Inverting True Inverting True

http://onsemi.com

LOW POWER SCHOTTKY

FUNCTION TABLE
CONTROL INPUTS G L L H DIR L H X LS640 LS642 B data to A bus A data to B bus Isolation OPERATION LS641 LS645 B data to A bus A data to B bus Isolation

20 1

PLASTIC N SUFFIX CASE 738

H = HIGH Level, L = LOW Level, X = Irrelevant 20

GUARANTEED OPERATING RANGES (SN74LS640, SN74LS645)

Symbol VCC TA IOH Parameter Supply Voltage Operating Ambient Temperature Range Output Current High Min 4.75 0 Typ 5.0 25 Max 5.25 70 3.0 15 IOL Output Current Low 24 Unit V C mA mA mA
1

SOIC DW SUFFIX CASE 751D

ORDERING INFORMATION
Device SN74LS640N SN74LS640DW SN74LS641N Package 16 Pin DIP 16 Pin 16 Pin DIP 16 Pin 16 Pin DIP 16 Pin 16 Pin DIP 16 Pin Shipping 1440 Units/Box 2500/Tape & Reel 1440 Units/Box 2500/Tape & Reel 1440 Units/Box 2500/Tape & Reel 1440 Units/Box 2500/Tape & Reel

GUARANTEED OPERATING RANGES (SN74LS641, SN74LS642)

Symbol VCC TA VOH IOL Parameter Supply Voltage Operating Ambient Temperature Range Output Voltage High Output Current Low Min 4.75 0 Typ 5.0 25 Max 5.25 70 5.5 24 Unit V C V mA

SN74LS641DW SN74LS642N SN74LS642DW SN74LS645N SN74LS645DW

Semiconductor Components Industries, LLC, 1999

244

December, 1999 Rev. 6

Publication Order Number: SN74LS640/D

SN74LS640 SN74LS641 SN74LS642 SN74LS645

CONNECTION DIAGRAMS DIP (TOP VIEW)
ENABLE B1 VCC G 20 19 18 B2 17 B3 16 B4 15 B5 14 B6 13 B7 12 B8 11 VCC 20 ENABLE B1 G 19 18 B2 17 B3 16 B4 15 B5 14 B6 13 B7 12 B8 11

1 DIR

2 A1

3 A2

4 A3

5 A4

6 A5

7 A6

8 A7

9 A8

10 GND

1 DIR

2 A1

3 A2

4 A3

5 A4

6 A5

7 A6

8 A7

9 A8

10 GND

SN74LS640 SN74LS642

SN74LS641 SN74LS645

http://onsemi.com
245

SN74LS640 SN74LS641 SN74LS642 SN74LS645 SN74LS640 SN74LS645

DC CHARACTERISTICS OVER OPERATING TEMPERATURE RANGE (unless otherwise specified)
Limits Symbol VIH VIL VIK VO OH Parameter Input HIGH Voltage Input LOW Voltage Input Clamp Diode Voltage Output HIGH Voltage 2.4 2.0 0.25 VO OL IOZH IOZL IIH IIL IOS Output LOW Voltage 0.35 Output Off Current HIGH Output Off Current LOW A or B, DIR or G Input HIGH Current Input LOW Current Output Short Circuit Current (Note 1) Power Supply Current Total Output HIGH ICC Total, Output LOW Total at HIGH Z 40 DIR or G A or B 0.5 20 400 20 0.1 0.1 0.4 225 70 90 95 mA VCC = MAX V A A A mA mA mA mA 0.4 0.65 3.4 Min 2.0 0.6 1.5 Typ Max Unit V V V V V V Test Conditions Guaranteed Input HIGH Voltage for All Inputs Guaranteed Input LOW Voltage for All Inputs VCC = MIN, IIN = 18 mA VCC = MIN, IOH = 3.0 mA VCC = MIN, IOH = MAX IOL = 12 mA IOL = 24 mA VCC = VCC MIN, VIN = VIL or VIH per Truth Table

VCC = MAX, VOUT = 2.7 V VCC = MAX, VOUT = 0.4 V VCC = MAX, VIN = 2.7 V VCC = MAX, VIN = 7.0 V VCC = MAX, VIN = 5.5 V VCC = MAX, VIN = 0.4 V VCC = MAX

Note 1: Not more than one output should be shorted at a time, nor for more than 1 second.

AC CHARACTERISTICS (TA = 25C, VCC = 5.0 V)

Limits LS640 Symbol tPLH tPHL tPLH tPHL tPZL tPZH tPZL tPZH tPLZ tPHZ tPLZ tPHZ Parameter Propagation Delay A to B Propagation Delay B to A Output Enable Time G, DIR to A Output Enable Time G, DIR to B Output Disable Time G, DIR to A Output Disable Time G, DIR to B Min Typ 6.0 8.0 6.0 8.0 31 23 31 23 15 15 15 15 Max 10 15 10 15 40 40 40 40 25 25 25 25 Min LS645 Typ 8.0 11 8.0 11 31 26 31 26 15 15 15 15 Max 15 15 15 15 40 40 40 40 25 25 25 25 Unit ns ns ns ns ns CL = 5 0 pF 5.0 ns Test Conditions

CL = 45 pF, RL = 667

http://onsemi.com
246

SN74LS640 SN74LS641 SN74LS642 SN74LS645 SN74LS641 SN74LS642

DC CHARACTERISTICS OVER OPERATING TEMPERATURE RANGE (unless otherwise specified)
Limits Symbol VIH VIL VIK IOH VO OL Parameter Input HIGH Voltage Input LOW Voltage Input Clamp Diode Voltage Output HIGH Current 0.25 Output LOW Voltage 0.35 IIH IIL Input HIGH Current 0.1 Input LOW Current Power Supply Current Total, Output HIGH ICC Total, Output LOW Total at HIGH Z 0.4 70 90 95 mA A VCC = MAX 0.5 20 V A mA mA IOL = 24 mA 0.65 Min 2.0 0.6 1.5 100 0.4 Typ Max Unit V V V A V Test Conditions Guaranteed Input HIGH Voltage for All Inputs Guaranteed Input LOW Voltage for All Inputs VCC = MIN, IIN = 18 mA VCC = MIN, VOH = MAX IOL = 12 mA VCC = VCC MIN, VIN = VIL or VIH per Truth Table

VCC = MAX, VIN = 2.7 V VCC = MAX, VIN = 7.0 V VCC = MAX, VIN = 0.4 V

AC CHARACTERISTICS (TA = 25C, VCC = 5.0 V)

Limits LS641 Symbol tPLH tPHL tPLH tPHL tPLH tPHL tPLH tPHL Parameter Propagation Delay, A to B Propagation Delay, B to A Propagation Delay, G, DIR to A Propagation Delay, G, DIR to B Min Typ 17 16 17 16 23 34 25 37 Max 25 25 25 25 40 50 40 50 Min LS642 Typ 19 14 19 14 26 43 28 39 Max 25 25 25 25 40 60 40 60 Unit ns ns ns ns CL = 45 pF, RL = 667 Test Conditions

http://onsemi.com
247

SN74LS670 4 x 4 Register File with 3-State Outputs

The TTL / MSI SN74LS670 is a high-speed, low-power 4 x 4 Register File organized as four words by four bits. Separate read and write inputs, both address and enable, allow simultaneous read and write operation. The 3-state outputs make it possible to connect up to 128 outputs to increase the word capacity up to 512 words. Any number of these devices can be operated in parallel to generate an n-bit length.
http://onsemi.com

Simultaneous Read / Write Operation Expandable to 512 Words by n-Bits Typical Access Time to 20 ns 3-State Outputs for Expansion Typical Power Dissipation of 125 mW

LOW POWER SCHOTTKY

GUARANTEED OPERATING RANGES

Symbol VCC TA IOH IOL Parameter Supply Voltage Operating Ambient Temperature Range Output Current High Output Current Low Min 4.75 0 Typ 5.0 25 Max 5.25 70 2.6 24 Unit V C mA mA
16 1

PLASTIC N SUFFIX CASE 648

16 1

SOIC D SUFFIX CASE 751B

ORDERING INFORMATION
Device SN74LS670N SN74LS670D Package 16 Pin DIP 16 Pin Shipping 2000 Units/Box 2500/Tape & Reel

Semiconductor Components Industries, LLC, 1999

248

December, 1999 Rev. 6

Publication Order Number: SN74LS670/D

SN74LS670
CONNECTION DIAGRAM DIP (TOP VIEW)
VCC 16 D1 15 WA 14 WB 13 EW 12 ER 11 Q1 10 Q2 9 NOTE: The Flatpak version has the same pinouts (Connection Diagram) as the Dual In-Line Package. 1 D2 2 D3 3 D4 4 RB 5 RA 6 Q4 7 Q3 8 GND

LOADING (Note a) PIN NAMES D1 D4 WA, WB EW RA, RB ER Q1 Q4 Data Inputs Write Address Inputs Write Enable (Active LOW) Input Read Address Inputs Read Enable (Active LOW) Input Outputs HIGH 0.5 U.L. 0.5 U.L. 1.0 U.L. 0.5 U.L. 1.5 U.L. 65 U.L. LOW 0.25 U.L. 0.25 U.L. 0.5 U.L. 0.25 U.L. 0.75 U.L. 15 U.L.

NOTES: a) 1 TTL Unit Load (U.L.) = 40 mA HIGH/1.6 mA LOW.

LOGIC SYMBOL
12 14 13 5 4 WA EW WB RA RB ER 11 15 1 2 3 D1 D2 D3 D4

Q1 Q2 Q3 Q4 10 9 7 6

VCC = PIN 16 GND = PIN 8

http://onsemi.com
249

SN74LS670
LOGIC DIAGRAM
D4
12 3

D3
2

D2
1

D1
15

EW
13

WB
14

WA WORD 0 G Q D G Q D G Q D G Q D

G Q

G Q

G Q

G Q

WORD 1

WORD 2 G Q D G Q D G Q D G Q D

WORD 3 G Q
4

G Q

G Q

G Q

RB

11

ER

RA

10

Q4

Q3 VCC = PIN 16 GND = PIN 8 = PIN NUMBERS

Q2

Q1

http://onsemi.com
250

SN74LS670
DC CHARACTERISTICS OVER OPERATING TEMPERATURE RANGE (unless otherwise specified)
Limits Symbol VIH VIL VIK VOH Parameter Input HIGH Voltage Input LOW Voltage Input Clamp Diode Voltage Output HIGH Voltage 2.4 0.65 3.1 0.25 VO OL IOZH IOZL Output LOW Voltage 0.35 Output Off Current HIGH Output Off Current LOW Input HIGH Current D, R, W EW ER D, R, W EW ER Input LOW Current D, R, W EW ER Short Circuit Current (Note 1) Power Supply Current 30 0.5 20 20 20 40 60 0.1 0.2 0.3 0.4 0.8 1.2 130 50 V A A A IOL = 24 mA 0.4 Min 2.0 0.8 1.5 Typ Max Unit V V V V V Test Conditions Guaranteed Input HIGH Voltage for All Inputs Guaranteed Input LOW Voltage for All Inputs VCC = MIN, IIN = 18 mA VCC = MIN, IOH = MAX, VIN = VIH or VIL per Truth Table IOL = 12 mA VCC = VCC MIN, VIN = VIL or VIH per Truth Table

VCC = MAX, VO = 2.7 V VCC = MAX, VO = 0.4 V

VCC = MAX, VIN = 2.7 V

IIH

mA

VCC = MAX, VIN = 7.0 V

IIL

mA

VCC = MAX, VIN = 0.4 V

IOS ICC

mA mA

VCC = MAX VCC = MAX

Note 1: Not more than one output should be shorted at a time, nor for more than 1 second.

http://onsemi.com
251

SN74LS670
AC CHARACTERISTICS (TA = 25C)
Limits Symbol tPLH tPHL tPLH tPHL tPLH tPHL tPZH tPZL tPLZ tPHZ Parameter Propagation Delay, RA or RB to Output Propagation Delay, EW to Output Propagation Delay, Data to Output Output Enable Time Output Disable Time Min Typ 23 25 26 28 25 23 15 22 16 30 Max 40 45 45 50 45 40 35 40 35 50 Unit ns ns ns ns ns CL = 5.0 pF VCC = 5.0 V, CL = 45 pF Test Conditions

AC SETUP REQUIREMENTS (TA = 25C)

Limits Symbol tW ts ts th th trec Parameter Pulse Width Setup Time, (D) Setup Time, (W) Hold Time, (D) Hold Time, (W) Recovery Time Min 25 10 15 15 5.0 25 Typ Max Unit ns ns ns ns ns ns VCC = 5 0 V 5.0 Test Conditions

AC WAVEFORMS

D, EW

1.3 V tPHL

1.3 V tPLH 1.3 V 1.3 V

RA, RB

1.3 V tPHL

1.3 V tPLH 1.3 V 1.3 V

Figure 1.

Figure 2.

WA, WB

1.3 V ts

1.3 V th 1.3 V 1.3 V ts th 1.3 V

D tW EW 1.3 V

Figure 3.

http://onsemi.com
252

SN74LS682 SN74LS684 SN74LS688 8-Bit Magnitude Comparators

The SN74LS682, 684, 688 are 8-bit magnitude comparators. These device types are designed to perform comparisons between two eight-bit binary or BCD words. All device types provide P = Q outputs and the LS682 and LS684 have P >Q outputs also. The LS682, LS684 and LS688 are totem pole devices. The LS682 has a 20 k pullup resistor on the Q inputs for analog or switch data.
OUTPUT ENABLE no no yes OUTPUT CONFIGURATION totem-pole totem-pole totem-pole

http://onsemi.com

LOW POWER SCHOTTKY

TYPE LS682 LS684 LS688

P=Q yes yes yes

P>Q yes yes no

PULLUP yes no no
20

GUARANTEED OPERATING RANGES

Symbol VCC TA IOH IOL Parameter Supply Voltage Operating Ambient Temperature Range Output Current High Output Current Low Min 4.75 0 Typ 5.0 25 Max 5.25 70 0.4 24 Unit V C mA mA

PLASTIC N SUFFIX CASE 738

20 1

SOIC DW SUFFIX CASE 751D

ORDERING INFORMATION
Device SN74LS682N SN74LS682DW SN74LS684N SN74LS684DW SN74LS688N SN74LS688DW Package 16 Pin DIP 16 Pin 16 Pin DIP 16 Pin 16 Pin DIP 16 Pin Shipping 1440 Units/Box 2500/Tape & Reel 1440 Units/Box 2500/Tape & Reel 1440 Units/Box 2500/Tape & Reel

Semiconductor Components Industries, LLC, 1999

253

December, 1999 Rev. 6

Publication Order Number: SN74LS682/D

SN74LS682 SN74LS684 SN74LS688

CONNECTION DIAGRAMS (TOP VIEW)
VCC P=Q 20 19 Q7 18 P7 17 Q6 16 P6 15 Q5 14 P5 13 Q4 12 P4 11

SN74LS682/684

1 P>Q

2 P0

3 Q0

4 P1

5 Q1

6 P2

7 Q2

8 P3

9 Q3

10 GND

VCC P=Q 20 19

Q7 18

P7 17

Q6 16

P6 15

Q5 14

P5 13

Q4 12

P4 11

SN74LS688

1 G

2 P0

3 Q0

4 P1

5 Q1

6 P2

7 Q2

8 P3

9 Q3

10 GND

FUNCTION TABLE
INPUTS DATA P, Q P=Q P>Q P<Q X ENABLES G, GT L L L H G2 L L L H P=Q L H H H P>Q H L H H OUTPUTS

H = HIGH Level, L = LOW Level, X = Irrelevant

http://onsemi.com
254

SN74LS682 SN74LS684 SN74LS688

DC CHARACTERISTICS OVER OPERATING TEMPERATURE RANGE (unless otherwise specified)
Limits Symbol VIH VIL VIK VOH Parameter Input HIGH Voltage Input LOW Voltage Input Clamp Diode Voltage Output HIGH Voltage 2.7 0.65 3.5 0.25 VO OL Output LOW Voltage 0.35 0.5 20 IIH Input HIGH Current LS682-Q Inputs Others LS682-Q Inputs IIL IOS Input LOW Current Others Short Circuit Current (Note 1) LS682 ICC Power S P Supply l Current LS684 LS688 30 0.2 130 70 65 65 mA mA mA mA mA VCC = MAX 0.1 0.1 0.4 V A mA mA mA VCC = MAX, VIN = 0 4 V MAX 0.4 VCC = MAX IOL = 24 mA 0.4 Min 2.0 0.8 1.5 Typ Max Unit V V V V V Test Conditions Guaranteed Input HIGH Voltage for All Inputs Guaranteed Input LOW Voltage for All Inputs VCC = MIN, IIN = 18 mA VCC = MIN, IOH = MAX, VIN = VIH or VIL per Truth Table IOL = 12 mA VCC = VCC MIN, VIN = VIL or VIH per Truth Table

VCC = MAX, VIN = 2.7 V VCC = MAX, VIN = 5.5 V VCC = MAX, VIN = 7.0 V

Note 1: Not more than one output should be shorted at a time, nor for more than 1 second.

http://onsemi.com
255

SN74LS682 SN74LS684 SN74LS688

LOGIC DIAGRAMS

P7 Q7 P6 Q6 P5 Q5 P4 Q4 P3 Q3 P2 Q2 P1 Q1 P0 Q0

(17) (18) (15) (16) (13) (14) (11) (12) (8) (9) (6) (7) (4) (5) (2) (3) (19)

P7 Q7 P6 Q6 P5 Q5 P4 Q4 P3 Q3 P2 Q2 P1
(1)

(17) (18) (15) (16) (13) (14) (11) (12) (8) (9) (6) (7) (4) (5) (2) (3)
(19)

P=Q

P=Q

Q1 P0 Q0

P>Q

(1)

SN74LS682 and LS684

SN74LS688

http://onsemi.com
256

SN74LS682 SN74LS684 SN74LS688

AC CHARACTERISTICS (TA = 25C) SN74LS682
Limits Symbol tPLH tPHL tPLH tPHL tPLH tPHL tPLH tPHL Parameter Propagation Delay, P to P = Q Propagation Delay, Q to P = Q Propagation Delay, P to P > Q Propagation Delay, Q to P > Q Min Typ 13 15 14 15 20 15 21 19 Max 25 25 25 25 30 30 30 30 Unit ns ns ns ns Test Conditions

VCC = 5.0 V F CL = 45 pF RL = 667

SN74LS684
Limits Symbol tPLH tPHL tPLH tPHL tPLH tPHL tPLH tPHL Parameter Propagation Delay, P to P = Q Propagation Delay, Q to P = Q Propagation Delay, P to P > Q Propagation Delay, Q to P > Q Min Typ 15 17 16 15 22 17 24 20 Max 25 25 25 25 30 30 30 30 Unit ns ns ns ns Test Conditions

VCC = 5.0 V F CL = 45 pF RL = 667

SN74LS688
Limits Symbol tPLH tPHL tPLH tPHL tPLH tPHL Parameter Propagation Delay, P to P = Q Propagation Delay, Q to P = Q Propagation Delay, G , G1 to P = Q Min Typ 12 17 12 17 12
13

Max 18 23 18 23 18 20

Unit ns ns ns

Test Conditions

VCC = 5.0 V CL = 45 pF RL = 667

http://onsemi.com
257

http://onsemi.com
258

CHAPTER 5 Reliability Data

http://onsemi.com
259

http://onsemi.com
260

RAP Reliability Audit Program for Logic Integrated Circuits

1.0 INTRODUCTION

The Reliability Audit Program developed in March 1977 is the ON Semiconductor internal reliability audit which is designed to assess outgoing product performance under accelerated stress conditions. Logic Reliability Engineering has overall responsibility for RAP, including updating its requirements, interpreting its results, administration at offshore locations, and monthly reporting of results. These reports are available at all sales offices.

RAP is a system of environmental and electrical tests performed periodically on randomly selected samples of standard products. Each sample receives the tests specified in section 2.0. Frequency of testing is specified per internal document 12MRM15301A.

http://onsemi.com
261

2.0 RAP TEST FLOW

Pull 500* piece sample from lot following Group A acceptance. 45* 340 Initial Seal** PTHB 48 hrs PTH*** 48 hrs 100

Op Life 40 hours

Temp Cycle 40 cycles interim test interim electrical

Interim Electrical

Add 460 cycles interim test Add 500 cycles final interim* test Temp Cycle# 1000 cycles (Additional)

Op Life 210 hrs (Additional) Final Interim# Electrical

PTH 48 hrs (Additional)

Op Life# 750 hrs (Additional)

Final Electrical (48 hrs)

Final Electrical (96 hrs)

Final Electrical & Seal** (2000 cycles) scrap

Final# Electrical (1000 hrs)

scrap # One sample per month for LS, 10H, 10K, MG CMOS, and HSL CMOS.

scrap

* PTHB or PTH not required for hermetic products: reduce total sample size to 450 pcs. Additional sample reductions for high pin-count devices per TABLE II notes. ** Seal (Fine & Gross Leak) required for hermetic products. *** PTH to be used when sockets for PTHB are not available.

3.0 TEST CONDITIONS AND COMMENTS PTHB 15 psig/121C/100% RH at rated VCC or VEE PTHB to be performed on plastic encapsulated devices PTHB only. TEMP CYCLING MIL-STD-883, Method 1010, Condition TEMP CYCLING C, 65C/+150C. OP LIFE MIL-STD-883, Method 1005, Condition C OP LIFE (Power plus Reverse Bias), TA = 145C.

NOTES:

1. All standard 25C dc and functional parameters will be measured Go/No/Go at each readout. 2. Any indicated failure is first verified and then submitted to the Product Analysis Lab for detailed analysis. 3. Sampling to include all package types routinely. 4. Device types sampled will be by generic type within each logic I/C product family (MECL, TTL, etc.) and will include all assembly locations. 5. 16 hrs. PTHB is equivalent to approximately 800 hours of 85C/85% RH THB for VCC 15 V. 6. Only moisture related failures (like corrosion) are criteria for failure on PTHB test. 7. Special device specifications (48As) for logic products will reference 12MRM15301A as source of generic data for any customer required monthly audit reports.

http://onsemi.com
262

CHAPTER 6 Package Information Including Surface Mount

http://onsemi.com
263

http://onsemi.com
264

BIPOLAR LOGIC SURFACE MOUNT WHY SURFACE MOUNT?

Surface Mount Technology is now being utilized to offer answers to many problems that have been created in the use of insertion technology. Limitations have been reached with insertion packages and PC board technology. Surface Mount Technology offers the opportunity to continue to advance the State-of-the-Art designs that cannot be accomplished with Insertion Technology. Surface Mount Packages allow more optimum device performance with the smaller Surface Mount configuration. Internal lead lengths, parasitic capacitance and inductance that placed limitations on chip performance have been reduced. The lower profile of Surface Mount Packages allows more boards to be utilized in a given amount of space. They are stacked closer together and utilize less total volume than insertion populated PC boards. Printed circuit costs are lowered with the reduction of the number of board layers required. The elimination or reduction of the number of plated through holes in the board, contribute significantly to lower PC board prices. Surface Mount assembly does not require the preparation of components that are common on insertion technology lines. Surface Mount components are sent directly to the assembly line, eliminating an intermediate step.

Automatic placement equipment is available that can place Surface Mount components at the rate of a few thousand per hour to hundreds of thousands of components per hour. Surface Mount Technology is cost effective, allowing the manufacturer the opportunity to produce smaller units and/or offer increased functions with the same size product.
SURFACE MOUNT AVAILABILITY

Bipolar Logic is currently offering LS-TTL in production quantities in SOIC packages. Refer to the following Selector Guide (SG366/D) which indicate availability and package type for these families. These families may be ordered in rails or on Tape and Reel. Refer to Tape and Reel information for ordering details.
THERMAL DATA

The power dissipation of surface mount packages is dependent on many factors that must be taken into consideration in the initial board design. The board material, the board surface metal thickness, pad area and the proximity to other heat generating components all have a bearing on the device dissipation capability.

200

180

C/W JA

160

MIN DIE SIZE 2K MILS2

140

120 SEE FIG. 2 FOR HEAT SINK DETAIL SO-8 (.090 x .110) LEADFRAME METAL = COPPER

MAX DIE SIZE 8K MILS2

100

SO-14 (.090 x .170)

SO-16 (.090 x .170) NARROW

PACKAGE STYLE DATA TAKEN USING PHILIPS SO TEST BOARD # 7322-078, 80873

Figure 1. Thermal Resistance, Junction-To-Ambient (C/W)

Measurement specimens are solder mounted on printed circuit card 19 mm 28 mm 1.5 mm in still air. No auxiliary thermal condition aids are used.

This data was collected using thermal test die in 20-pin PLCC packages on PLCC test boards (2.24 x 2.24 x .062 glass epoxy, type FR-4, with solder coated 1 oz./sq. ft. copper).

http://onsemi.com
265

TAPE AND REEL STANDARD BIPOLAR LOGIC INTEGRATED CIRCUITS

ON Semiconductor has now added the convenience of Tape and Reel packaging for our growing family of standard Integrated Circuit products. The packaging fully conforms

to the latest EIA RS-481A specification. The antistatic embossed tape provides a secure cavity sealed with a peel-back cover tape.

MECHANICAL POLARIZATION SOIC DEVICES

Typical

View is from tape side Linear direction of travel

GENERAL INFORMATION

Reel Size 13 inch (330 mm) Suffix R2 Tape Width 12 mm to 24 mm (see table) Units/Reel (see table) No Partial Reel Counts Available and Minimum Lot Size is Per Table
ORDERING INFORMATION

To order devices which are to be delivered in Tape and Reel, add the suffix R2 to the device number being ordered.
Table 1 Tape and Reel Data
Device Type SO-8 SO-14 SO-16 SO-16 Wide SO-20 Wide Tape Width (mm) 12 16 16 16 24 Device/Reel 2,500 2,500 2,500 1,000 1,000 Reel Size (inch) 13 13 13 13 13 Min Lot Size Per Part No. Tape and Reel 5,000 5,000 5,000 5,000 5,000

http://onsemi.com
266

PACKAGE OUTLINES
SOIC
Case 751A-02 D Suffix 14-Pin Plastic SO-14
NOTES: 1. DIMENSIONS A AND B ARE DATUMS AND T IS A DATUM SURFACE. 2. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 3. CONTROLLING DIMENSION: MILLIMETER. 4. DIMENSION A AND B DO NOT INCLUDE MOLD PROTRUSION. 5. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE. 6. 751A-01 IS OBSOLETE, NEW STANDARD 751A-02. DIM A B C D F G J K M P R MILLIMETERS MIN MAX 8.55 8.75 3.80 4.00 1.35 1.75 0.35 0.49 0.40 1.25 1.27 BSC 0.25 0.19 0.10 0.25 0 7 6.20 5.80 0.25 0.50 INCHES MIN MAX 0.337 0.344 0.150 0.157 0.054 0.068 0.014 0.019 0.016 0.049 0.050 BSC 0.008 0.009 0.004 0.009 0 7 0.229 0.244 0.010 0.019

-A14 8

-B1 7

P
7 PL

0.25 (0.010)

C
SEATING PLANE

R X 45

D 14 PL 0.25 (0.010)
M

K T B
S

-A-

Case 751B-03 D Suffix 16-Pin Plastic SO-16

9

16

-B1 8

P
8 PL

0.25 (0.010)

NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE. 5. 751B-01 IS OBSOLETE, NEW STANDARD 751B-03. MILLIMETERS MIN MAX 9.80 10.00 3.80 4.00 1.35 1.75 0.35 0.49 0.40 1.25 1.27 BSC 0.19 0.25 0.10 0.25 0 7 5.80 6.20 0.25 0.50 INCHES MIN MAX 0.386 0.393 0.150 0.157 0.054 0.068 0.014 0.019 0.016 0.049 0.050 BSC 0.008 0.009 0.004 0.009 0 7 0.229 0.244 0.010 0.019

R X 45 G -TD 16 PL 0.25 (0.010)

M

C
SEATING PLANE

K T B
S

DIM A B C D F G J K M P R

-A20 11

Case 751D-03 DW Suffix 20-Pin Plastic SO-20 (WIDE)

-B1 10

0.25 (0.010)
10 PL

NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE. 5. 751D-01, AND -02 OBSOLETE, NEW STANDARD 751D-03. DIM A B C D F G J K M P R MILLIMETERS MIN MAX 12.65 12.95 7.60 7.40 2.65 2.35 0.49 0.35 0.90 0.50 1.27 BSC 0.32 0.25 0.25 0.10 7 0 10.05 10.55 0.75 0.25 INCHES MIN MAX 0.499 0.510 0.292 0.299 0.093 0.104 0.014 0.019 0.020 0.035 0.050 BSC 0.010 0.012 0.004 0.009 7 0 0.395 0.415 0.010 0.029

G R X 45 -TC K
M SEATING PLANE

M D 20 PL 0.25 (0.010) T B
S

http://onsemi.com
267

PACKAGE OUTLINES
PLASTIC
Case 646-06 N Suffix 14-Pin Plastic
14 8

B
1 7

NOTES: 1. LEADS WITHIN 0.13 mm (0.005) RADIUS OF TRUE POSITION AT SEATING PLANE AT MAXIMUM MATERIAL CONDITION. 2. DIMENSION L TO CENTER OF LEADS WHEN FORMED PARALLEL. 3. DIMENSION B DOES NOT INCLUDE MOLD FLASH. 4. ROUNDED CORNERS OPTIONAL. 5. 646-05 OBSOLETE, NEW STANDARD 646-06. DIM A B C D F G H J K L M N MILLIMETERS MIN MAX 18.16 19.56 6.10 6.60 3.69 4.69 0.38 0.53 1.02 1.78 2.54 BSC 1.32 2.41 0.20 0.38 2.92 3.43 7.62 BSC 0 10 0.39 1.01 INCHES MIN MAX 0.715 0.770 0.240 0.260 0.145 0.185 0.015 0.021 0.040 0.070 0.100 BSC 0.052 0.095 0.008 0.015 0.115 0.135 0.300 BSC 0 10 0.015 0.039

A F C N H G D
SEATING PLANE

NOTE 4

J K M

-A16 9

Case 648-08 N Suffix 16-Pin Plastic

B
1 8

NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION L TO CENTER OF LEADS WHEN FORMED PARALLEL. 4. DIMENSION B DOES NOT INCLUDE MOLD FLASH. 5. ROUNDED CORNERS OPTIONAL. 6. 648-01 THRU -07 OBSOLETE, NEW STANDARD 648-08. DIM A B C D F G H J K L M S MILLIMETERS MIN MAX 18.80 19.55 6.35 6.85 3.69 4.44 0.39 0.53 1.02 1.77 2.54 BSC 1.27 BSC 0.21 0.38 2.80 3.30 7.50 7.74 0 10 0.51 1.01 INCHES MIN MAX 0.740 0.770 0.250 0.270 0.145 0.175 0.015 0.021 0.040 0.070 0.100 BSC 0.050 BSC 0.008 0.015 0.110 0.130 0.295 0.305 0 10 0.020 0.040

F S

C -TK
SEATING PLANE

H G D 16 PL 0.25 (0.010)
M

Case 738-03 N Suffix 20-Pin Plastic -A20 1 11 10

B C L

NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION L TO CENTER OF LEAD WHEN FORMED PARALLEL. 4. DIMENSION B DOES NOT INCLUDE MOLD FLASH. 5. 738-02 OBSOLETE, NEW STANDARD 738-03. DIM A B C D E F G J K L M N MILLIMETERS MIN MAX 25.66 27.17 6.60 6.10 4.57 3.81 0.55 0.39 1.27 BSC 1.77 1.27 2.54 BSC 0.38 0.21 3.55 2.80 7.62 BSC 15 0 1.01 0.51 INCHES MIN MAX 1.010 1.070 0.240 0.260 0.150 0.180 0.015 0.022 0.050 BSC 0.050 0.070 0.100 BSC 0.008 0.015 0.110 0.140 0.300 BSC 15 0 0.020 0.040

-TSEATING PLANE

K E G F D 20 PL 0.25 (0.010)
M

M J 20 PL 0.25 (0.010) T A
M M

T B

http://onsemi.com
268

ON SEMICONDUCTOR WORLDWIDE SALES OFFICES

UNITED STATES ALABAMA
Huntsville . . . . . . . . . . . . . . . . . . (256)4646800

CANADA ONTARIO
Ottawa . . . . . . . . . . . . . . . . . . . . (613)2263491

INTERNATIONAL (continued) KOREA

Seoul . . . . . . . . . . . . . . . . . . . . 82234407200

CALIFORNIA
Irvine . . . . . . . . . . . . . . . . . . . . . . (949)7537360 San Jose . . . . . . . . . . . . . . . . . . (408)7490510

QUEBEC
Montreal . . . . . . . . . . . . . . . . . . . (514)3333300

MALAYSIA
Penang . . . . . . . . . . . . . . . . . . . . 60(4)2282514

MEXICO INTERNATIONAL BRAZIL

Sao Paulo . . . . . . . . . . . . . 55(011)30305244 Guadalajara . . . . . . . . . . . . . . . . 52(36)780750

COLORADO
Denver . . . . . . . . . . . . . . . . . . . . (303)3373434

PHILIPPINES
Manila . . . . . . . . . . . . . . . . . . . . (63)2 8078455

FLORIDA
St. Petersberg . . . . . . . . . . . . . . (813)5244177

GEORGIA
Atlanta . . . . . . . . . . . . . . . . . . . . (770)3383810

CHINA
Beijing . . . . . . . . . . . . . . . . . . . 861065642288 Guangzhou . . . . . . . . . . . . . . 862087537888 Shanghai . . . . . . . . . . . . . . . . 862163747668

PUERTO RICO
San Juan . . . . . . . . . . . . . . . . . . (787)6414100

SINGAPORE
Singapore . . . . . . . . . . . . . . . . . . . . (65)4818188

ILLINOIS
Chicago . . . . . . . . . . . . . . . . . . . (847)4132500

MASSACHUSETTS
Boston . . . . . . . . . . . . . . . . . . . . (781)9329700

FRANCE
Paris . . . . . . . . . . . . . . . . . . . . . . 33134 635900

SPAIN
Madrid . . . . . . . . . . . . . . . . . . . . . 34(1)4578204 or . . . . . . . . . . . . . . . . . . . . . . . . . 34(1)4578254

MICHIGAN
Detroit . . . . . . . . . . . . . . . . . . . . . (248)3476800

GERMANY
Munich . . . . . . . . . . . . . . . . . . . . 49 89 921030

SWEDEN
Stockholm . . . . . . . . . . . . . . . . . 46(8)7348800

MINNESOTA
Plymouth . . . . . . . . . . . . . . . . . . (612)2492360

HONG KONG
Hong Kong . . . . . . . . . . . . . . . 85226106888

TAIWAN
Taipei . . . . . . . . . . . . . . . . . . . 886(2)27058000

NORTH CAROLINA
Raleigh . . . . . . . . . . . . . . . . . . . . (919)8704355

INDIA
Bangalore . . . . . . . . . . . . . . . . . 91805598615

THAILAND
Bangkok . . . . . . . . . . . . . . . . . . . 66(2)2544910

PENNSYLVANIA
Philadelphia/Horsham . . . . . . . (215)9574100

ISRAEL
Tel Aviv . . . . . . . . . . . . . . . . . . . 97299522333

UNITED KINGDOM
Aylesbury . . . . . . . . . . . . . . . 44 1 (296)395252

TEXAS
Dallas . . . . . . . . . . . . . . . . . . . . . (972)5165100

ITALY
Milan . . . . . . . . . . . . . . . . . . . . . . . . 39(02)82201

JAPAN
Tokyo . . . . . . . . . . . . . . . . . . . 81354878345

http://onsemi.com
269

ON SEMICONDUCTOR STANDARD DOCUMENT TYPE DEFINITIONS

REFERENCE MANUAL A Reference Manual is a publication that contains a comprehensive system or devicespecific description of the structure and function (operation) of a particular part/system; used overwhelmingly to describe the functionality of a microprocessor, microcontroller, or some other submicron sized device. Procedural information in a Reference Manual is limited to less than 40 percent (usually much less). USERS GUIDE A Users Guide contains procedural, taskoriented instructions for using or running a device or product. A Users Guide differs from a Reference Manual in the following respects: * Majority of information (> 60%) is procedural, not functional, in nature * Volume of information is typically less than for Reference Manuals * Usually written more in active voice, using secondperson singular (you) than is found in Reference Manuals * May contain photographs and detailed line drawings rather than simple illustrations that are often found in Reference Manuals POCKET GUIDE A Pocket Guide is a pocketsized document that contains technical reference information. Types of information commonly found in pocket guides include block diagrams, pinouts, alphabetized instruction set, alphabetized registers, alphabetized thirdparty vendors and their products, etc. ADDENDUM A documentation Addendum is a supplemental publication that contains missing information or replaces preliminary information in the primary publication it supports. Individual addendum items are published cumulatively. Addendums end with the next revision of the primary document. APPLICATION NOTE An Application Note is a document that contains realworld application information about how a specific ON Semiconductor device/product is used with other ON Semiconductor or vendor parts/software to address a particular technical issue. Parts and/or software must already exist and be available. A document called ApplicationSpecific Information is not the same as an Application Note. SELECTOR GUIDE A Selector Guide is a trifold (or larger) document published on a regular basis (usually quarterly) by many, if not all, divisions, that contains key lineitem, devicespecific information for particular product families. Some Selector Guides are published in book format and contain previously published information. PRODUCT PREVIEW A Product Preview is a summary document for a product/device under consideration or in the early stages of development. The Product Preview exists only until an Advance Information document is published that replaces it. The Product Preview is often used as the first section or chapter in a corresponding reference manual. The Product Preview displays the following disclaimer at the bottom of the first page: ON Semiconductor reserves the right to change or discontinue this product without notice. ADVANCE INFORMATION The Advance Information document is for a device that is NOT fully MCqualified. The Advance Information document is replaced with the Technical Data document once the device/part becomes fully MCqualified. The Advance Information document displays the following disclaimer at the bottom of the first page: This document contains information on a new product. Specifications and information herein are subject to change without notice. TECHNICAL DATA The Technical Data document is for a product/device that is in full production (i.e., fully released). It replaces the Advance Information document and represents a part that is M, X, XC, or MC qualified. The Technical Data document is virtually the same document as the Product Preview and the Advance Information document with the exception that it provides information that is unavailable for a product in the early phases of development (such as complete parametric characterization data). The Technical Data document is also a more comprehensive document that either of its earlier incarnations. This document displays no disclaimer, and while it may be informally referred to as a data sheet, it is not labeled as such. ENGINEERING BULLETIN An Engineering Bulletin is a writeup that typically focuses on a single specific solution for a particular engineering or programming issue involving one or several devices.

http://onsemi.com
270

Notes

http://onsemi.com
271

Notes

http://onsemi.com
272

ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Typical parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including Typicals must be validated for each customer application by customers technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer.

PUBLICATION ORDERING INFORMATION

NORTH AMERICA Literature Fulfillment: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: [email protected] N. American Technical Support: 800-282-9855 Toll Free USA/Canada EUROPE: LDC for ON Semiconductor - European Support German Phone: (+1) 303-308-7140 (M-F 2:30pm to 5:00pm Munich Time) Email: [email protected] French Phone: (+1) 303-308-7141 (M-F 2:30pm to 5:00pm Toulouse Time) Email: [email protected] English Phone: (+1) 303-308-7142 (M-F 1:30pm to 5:00pm UK Time) Email: [email protected] ASIA/PACIFIC: LDC for ON Semiconductor - Asia Support Phone: 303-675-2121 (Tue-Fri 9:00am to 1:00pm Hong Kong Time) Toll Free from Hong Kong 800-4422-3781 Email: [email protected] JAPAN: ON Semiconductor, Japan Customer Focus Center 4-32-1 Nishi-Gotanda, Shinagawa-ku, Tokyo, Japan 141-8549 Phone: 81-3-5740-2745 Email: [email protected] Fax Response Line: 303-675-2167 800-344-3810 Toll Free USA/Canada ON Semiconductor Website: http://onsemi.com For additional information, please contact your local Sales Representative

DL121/D