LISI AEROSPACE – Please refer to Central Documentation Website to check validity

S
HI-SHEAR Corporation, USA Design Holder CAGE No. 73197
AEROSPACE
a LISI AEROSPACE Company
For the current list of licensed manufacturers, please visit the
hi-shear corporation
LISI AEROSPACE website at:
2600 SKYPARK DRIVE, TORRANCE, CALIFORNIA 90509 U.S.A. 24 HTTP://WWW.LISI-AEROSPACE.COM/LICENSES

INDENTED HEAD MARKING .010 MAX DEPTH. (MAX GRIP + B)± .010
"hs" INDICATES HI-SHEAR TRADEMARK. THE REMAINING PORTION OF HI-LITE™
NUMBER(S) FOLLOWING THE TRADEMARK 32 COLLAR AFTER ASSEMBLY
INDICATES FIRST DASH NUMBER. MAX GRIP ± .005 T1 S CHAMFER
ARRANGEMENT OPTIONAL. TYPICAL COLLARS:
H W HST1087
R RAD T

45°

756
HST

A Y 100°
DIA DIA 90°
8

h
s

D TD
DIA DIA
G
THREAD ROLLED PER AS8879 COLLAR WRENCHING
SEE VIEW A (MODIFIED). MAJOR DIA SHALL DEVICE AUTOMATICALLY
BE PER "TD" SHEARS OFF
HI-LITE™ PIN
HI-LITE™ PIN AND COLLAR AFTER ASSEMBLY

SEE COLLAR STANDARDS

FOR COLLAR STRENGTHS.
LOWER STRENGTH (PIN OR
COLLAR) DETERMINES
SYSTEM STRENGTH.
24

D DIA SOCKET DOUBLE TENSION-

FIRST PIN A B TD G R S SHEAR TENSION TENSION
DASH NOM
WITHOUT WITH
CHAMFER THREAD T T1 POUNDS
DIA REF COATING COATING
DIA REF H RAD W Y POUNDS FATIGUE
NO. DIA OR SOLID OR SOLID REF MODIFIED
HEX DEPTH DEPTH DIA MINIMUM
FILM FILM MIN MAX MINIMUM LBS. MAX.
.322 .1635 .1635 .1595 .065 .025 .1640-32 .0806
5 5/32
.306
.280
.1630 .1625 .1570
.030
.055 .015
1/32 x 37° UNJC-3A .0791
.080 .135 5 4,010 2,180 715 THIS AREA OF SPECIAL CONFIGURATION
AND COLD WORKING TO MEET PHYSICAL
.377 .1895 .1895 .1840 .074 .025 .1900-32 .0806 .119 REQUIREMENTS
6 3/16 .290 .035 1/32 x 37° UNJF-3A .080 .135 5,380 3,180 1,050
.357 .1890 .1885 .1810 .064 .015 .0791 .104
.410 .2182 .2182 .2100 .081 .025 .2160-28 .0806 .119
7 7/32 .305 .040 1/32 x 37° UNJF-3A .080 .145 7,194 4,000 1,360
.390 .2177 .2172 .2070 .071 .015 .0791 .104
.440 .2495 .2495 .2440 .090 .025 .2500-28 .0967 .142
8 1/4 .320 .045 1/32 x 37° UNJF-3A .090 .160 9,300 5,820 1,950
.415 .2490 .2485 .2410 .080 .015 .0947 .122
.505 .3120 .3120 .3060 .112 .030 .3125-24 .1295 .180
10 5/16 .380 .055 3/64 x 37° UNJF-3A .110 .200 14,600 9,200 3,140
.475 .3115 .3110 .3020 .102 .020 .1270 .160
.600 .3745 .3745 .3680 .140 .030 .3750-24 .1617 .217
12 3/8 .420 .075 3/64 x 37° UNJF-3A .140 .235 21,000 14,000 4,850
.565 .3740 .3735 .3640 .130 .020 .1582 .197
.676 .4370 .4370 .4310 .160 .030 .4375-20 .1930 .253 VIEW A
14 7/16 .485 .095 3/64 x 37° UNJF-3A .170 .275 28,600 17,670 6,120
.641 .4365 .4360 .4260 .150 .020 .1895 .233 HI-LITE™ THREAD TRANSITION AREA
.770 .4995 .4995 .4930 .188 .030 .5000-20 .2242 .289 SEE SPECIFICATION FOR INSPECTION
16 1/2 .525 .095 3/64 x 37° UNJF-3A .200 .315 37,300 23,940 8,340
.735 .4990 .4985 .4880 .178 .020 .2207 .269
.877 .5615 .5615 .5550 .210 .040 .5625-18 .2555 .326
18 9/16 .600 .125 1/16 x 37° UNJF-3A .240 .365 47,200 28,350 9,900
.842 .5610 .5605 .5500 .200 .025 .2520 .306
.953 .6240 .6240 .6180 .238 .040 .6250-18 .2555 .326
20 5/8 .640 .140 1/16 x 37° UNJF-3A .240 .365 58,300 38,360 13,470
.918 .6235 .6230 .6120 .228 .025 .2520 .306

"HI-LITE", "HST", AND "HI-KOTE",

ARE TRADEMARKS OF HI-SHEAR CORPORATION
HST756

DRAWN BY DATE TITLE

D.P.S. 1983-02-04 HI-LITE™ PIN

PROTRUDING TENSION HEAD
APPROVED DATE
TITANIUM
R.TING 1983-02-22
1/16 GRIP VARIATION
REVISION DATE DRAWING NUMBER
M.BEARD
24 2017-04-27
HST756 1 OF 2

C 2017 Hi-Shear Corporation

 LISI AEROSPACE – Please refer to Central Documentation Website to check validity

S
AEROSPACE

hi-shear corporation
2600 SKYPARK DRIVE, TORRANCE, CALIFORNIA 90509 U.S.A.

GENERAL NOTES: 1. Concentricity: "A" to "D" diameter within .010 FIM. SPECIFICATION: HI-LITE™ Product Specification 380, except fatigue loads as tabulated .
24 2. Dimensions are in inches and to be met after finish.
24 3. Surface texture per ASME B46.1. CODE: First dash number indicates nominal diameter in 1/32nds.
4. Hole preparation per NAS618. Second dash number indicates maximum grip in 1/16ths.
See Finish note for explanation of code letters.
5 Evidence of broken edge across points.
6. Use HST856 for oversize replacement.
HOW TO ORDER
24 7 After February, 21st of 2015, HI-KOTE™ 1 aluminum pigmented coating per 24 EXAMPLE: Pin Part Number
Hi-Shear Spec. 294 will be replaced by REACH compliant HI-KOTE™ 1 NC HST756AP8-8
aluminum pigmented coating per Hi-Shear Spec. 294 on fasteners coated in
European Union.
8/16 or 1/2 Maximum Grip Length
MATERIAL: 6AL-4V titanium alloy per AMS4928 or AMS4967. 8/32 or 1/4 Nominal Diameter Pin
Finish Code
Pin Basic Part Number
HEAT TREAT: 95,000 psi shear minimum.

FINISH: HST756-( )-( ) = Surface coating per Hi-Shear Spec. 306, Type I, color blue, with color black
on thread end, and cetyl alcohol lube per Hi-Shear Spec. 305.
24 7 HST756AP( )-( ) = HI-KOTE™ 1 aluminum coating per Hi-Shear Spec. 294, and cetyl alcohol
lube per Hi-Shear Spec. 305.
24 7 HST756AT( )-( ) = HI-KOTE™ 1 aluminum coating per Hi-Shear Spec. 294.
HST756CE( )-( ) = I.V.D. aluminum coating per MIL-DTL-83488, Type II (.00015-.00045 thick), with
color black on thread end, and cetyl alcohol lube per Hi-Shear Spec. 305.
HST756CF( )-( ) = I.V.D. aluminum coating per MIL-DTL-83488, Type II (.00015-.00045 thick), with
color black on thread end.
HST756JB( )-( ) = I.V.D. aluminum coating per MIL-DTL-83488, Type II, (.00015-.00045 thick) or EN6118,
and cetyl alcohol lube per Hi-Shear Spec. 305 or EN6117.
24 7 HST756KM( )-( ) = HI-KOTE™ 1 aluminum coating per Hi-Shear Spec. 294, with color white on thread
end, and cetyl alcohol lube per Hi-Shear Spec. 305.
24 7 HST756KN( )-( ) = HI-KOTE™ 1 aluminum coating per Hi-Shear Spec. 294, with color white on thread
end.
HST756RP( )-( ) = Phosphate fluoride treat with color code orange on thread end, and cetyl
alcohol lube per Hi-Shear Spec. 305.
HST756UV( )-( ) = Surface coating per Hi-Shear Spec. 306, Type II, HI-KOTE™ 2 solid film lube per
Hi-Shear Spec. 292, and cetyl alcohol lube per Hi-Shear Spec. 305.
HST756VF( )-( ) = Surface coating per Hi-Shear Spec. 306, Type I, color blue, and cetyl alcohol
lube per Hi-Shear Spec. 305.
HST756NKJ( )-( ) = HI-KOTE™ 1 NC aluminum pigmented coating per Hi-Shear Spec. 294
with color silver on thread end and cetyl alcohol lube per Hi-Shear Spec. 305.
HST756NKK( )-( ) = Sulfuric acid anodizing per ISO8080 and HI-KOTE™ 1 NC aluminum
pigmented coating per Hi-Shear Spec. 294 on threads only with color silver on
thread end and cetyl alcohol lube per Hi-Shear Spec. 305.
HST756NKL( )-( ) = HI-KOTE™ 1 NC aluminum pigmented coating per Hi-Shear Spec. 294
on threads only with color silver on thread end and cetyl alcohol lube
per Hi-Shear Spec. 305.
HST756

DRAWING NUMBER

HST756 2 OF 2
C 2017 Hi-Shear Corporation