FMC130 Data acquisition settings - Wiki Knowledge Base | Teltonika GPS https://wiki.teltonika-gps.

com/view/FMC130_Data_acquisition_settings

Namespaces

▪ PagePage

Variants

Views

▪ Read
▪ View source
▪ View history
▪ PDF Export

More

▪ Read
▪ View source
▪ View history
▪ PDF Export
▪ Page
▪ Discussion

Search

Search Wiki Knowledge BaseSearch

FMC130 Data acquisition settings

Contents

1 de 10 08-11-2024, 16:38
FMC130 Data acquisition settings - Wiki Knowledge Base | Teltonika GPS https://wiki.teltonika-gps.com/view/FMC130_Data_acquisition_settings

▪ 1 Data Acquisition
▪ 2 Record Saving settings
▪ 3 On Demand Tracking

Data Acquisition
Data Acquisition modes are an essential part of FMC130 device, they are also highly con�gurable.
Through con�guration user de�nes how records will be saved and sent. There are three di�erent modes: Home, Roaming, and
Unknown. All these modes with con�gured data acquisition and report frequencies depend on the current GSM Operator de�ned in the
Operator list (see section GSM Operators settings) and are switched when GSM operator changes (e.g. vehicle passes through a country
border).
If current GSM operator is de�ned as Home Operator, the device will work in Home Data Acquisition mode, if the current operator is
de�ned as Roaming Operator, the device will work in Roaming Data Acquisition mode, and if the current operator code is not written in
the Roaming Operator list, the device will work in Unknown mode.
This functionality allows having di�erent AVL records to acquire and send parameter values when the object is moving or standing still.
Vehicle moving or stop state is de�ned by the Stop Detection Source parameter. There are 4 ways for FMC130 to switch between
Vehicle on Stop and Vehicle Moving modes, please refer to the �rst table in System settings.
FMC130 has 6 di�erent modes. Operational logic is shown in the �gure below.

If home operator is written to roaming operator list, it will still be detected as home operator.

2 de 10 08-11-2024, 16:38
FMC130 Data acquisition settings - Wiki Knowledge Base | Teltonika GPS https://wiki.teltonika-gps.com/view/FMC130_Data_acquisition_settings

The operator search is performed every 15 minutes. Depending on the current GSM operator Home, Roaming or Unknown mode can
be changed faster than every 15 minutes. This process is separate from the operator search. Movement criteria are checked every
second.

3 de 10 08-11-2024, 16:38
FMC130 Data acquisition settings - Wiki Knowledge Base | Teltonika GPS https://wiki.teltonika-gps.com/view/FMC130_Data_acquisition_settings

Record Saving settings

4 de 10 08-11-2024, 16:38
FMC130 Data acquisition settings - Wiki Knowledge Base | Teltonika GPS https://wiki.teltonika-gps.com/view/FMC130_Data_acquisition_settings

Min Saved Records de�nes the minimum number of coordinates and I/O data that should be transferred within a single connection to
the server. If FMC130 does not have enough coordinates to send to the server, it will check again after a time interval de�ned in Send
Period �eld.
Send period controls the frequency of data being sent to the server over GPRS. The module makes attempts to send collected data to
the server every de�ned period of time. If it does not have enough records (depends on the parameter Min. Saved Records described
above), it tries again after the de�ned time interval.

Keep in mind that FMC130 operates in GMT:0 time zone, without daylight saving.

FMC130 is able to collect records using four methods at the same time: time, distance, angle, and speed-based data acquisition:

▪ Time based data acquisition (Min Period) – records are acquired every time when a de�ned interval of time passes. Entering zero
disables data acquisition based on time.
▪ Distance-based data acquisition (Min Distance) – records are acquired when the distance between the previous coordinate and
current position is greater than a de�ned parameter value. Entering zero disables data acquisition based on distance.
▪ Angle based data acquisition (Min Angle) – records are acquired when the angle di�erence between the last recorded coordinate
and current position is greater than a de�ned value. Entering zero disables data acquisition based on the angle.
▪ Speed based data acquisition (Min Speed Delta) – records are acquired when the speed di�erence between the last recorded
coordinate and current position is greater than a de�ned value. Entering zero disables data acquisition based on speed.

5 de 10 08-11-2024, 16:38
FMC130 Data acquisition settings - Wiki Knowledge Base | Teltonika GPS https://wiki.teltonika-gps.com/view/FMC130_Data_acquisition_settings

On Demand Tracking
This functionality was made global (for all FMB devices) from 03.25.06.Rev.00. Tracking on Demand can be activated using commands.
After device receives SMS/GPRS command " on_demand_trackingX" where X is a number from 0 to 2.

Possible X values are:

▪ X = 0 – Stops Tracking on Demand functionality.

6 de 10 08-11-2024, 16:38
FMC130 Data acquisition settings - Wiki Knowledge Base | Teltonika GPS https://wiki.teltonika-gps.com/view/FMC130_Data_acquisition_settings

▪ X = 2 – Generates one high priority record and initiates data sending to the server.

After that, the device starts to generate high priority records and initiate data sending to the server. This feature is con�gurable via
SMS/GPRS commands only.

From version 03.25.11.Rev.00 tracking on demand can be triggered by multiple IO Events. To enable functionality at least one activation
source must be selected and an appropriate IO Event (in I/O tab) should be enabled (Low/High/Panic priority, the operand must NOT be
“Monitoring”). When IO Event is generated and if the event is enabled in activation sources, tracking on demand will be started. THE new
IO event will not interrupt or restart tracking on-demand until the Duration period has expired. If tracking on demand is already
running, SMS/GPRS command will restart tracking on demand. If tracking the on-demand period is lower than the normal record
acquisition period, only high priority records will be created. If tracking the on-demand period is larger than the normal record
acquisition period, low priority records will be created according to data acquisition con�guration and high priority records will be
created after con�gured tracking on-demand period. Some new Tracking on Demand parameters are introduced in devices.

7 de 10 08-11-2024, 16:38
FMC130 Data acquisition settings - Wiki Knowledge Base | Teltonika GPS https://wiki.teltonika-gps.com/view/FMC130_Data_acquisition_settings

8 de 10 08-11-2024, 16:38
FMC130 Data acquisition settings - Wiki Knowledge Base | Teltonika GPS https://wiki.teltonika-gps.com/view/FMC130_Data_acquisition_settings

There are three available options for the activation source of tracking on demand - DIN/AIN or both (devices that support multiple DINs/
AINs allow choosing which DINs/AINs to use). Note that, these inputs will work as buttons, rather than switches, and are used to trigger
the functionality, the duration of tracking on demand will not be extended if the activation source status is high for a period of time.

Retrieved from "https://wiki.teltonika-gps.com/index.php?title=FMC130_Data_acquisition_settings&oldid=35647"

▪ This page was last edited on 16 May 2019, at 13:26.

▪ Use Cases
▪ All use cases
▪ Fleet telematics
▪ Logistics & delivery services
▪ Car sharing, rental & leasing
▪ E-Mobility management
▪ Utility & emergency transport
▪ Agriculture, construction & mining
▪ Assets & workforce
▪ Driver safety

▪ Products
▪ Trackers
▪ Accessories
▪ Solutions

▪ Support
▪ Product support
▪ Crowd Support Forum
▪ Warranty & repair
▪ EOL products

▪ About us
▪ Mission, vision & values
▪ Career

9 de 10 08-11-2024, 16:38
FMC130 Data acquisition settings - Wiki Knowledge Base | Teltonika GPS https://wiki.teltonika-gps.com/view/FMC130_Data_acquisition_settings

▪ Contacts

▪ ▪ Privacy
▪ Cookies
▪ All Policies
Copyright © 2024, Teltonika
Subscribe to newsletter

Connect

We use cookies to ensure that we give you the best experience on our website. If you continue to use this site we will assume that you
are happy with it.OkRead more

10 de 10 08-11-2024, 16:38