ULTRAPLAN

ECO
Self-levelling, ultra quick-hardening smoothing
compound for thicknesses from 1 to 10 mm

CLASSIFICATION ACCORDING TO EN 13813

Ultraplan Eco smoothing compound as described in this data sheet is classified as CT-C25-F7-A2 FL-s1
according to European Standard EN 13813.

WHERE TO USE
Ultraplan Eco, is used for levelling and smoothing differences in thicknesses from 1 to 10 mm on new or
existing substrates, preparing them to receive all kinds of flooring where excellent resistance to loads and
traffic is required.
Ultraplan Eco is especially suitable for areas subject to wheeled chairs.
Ultraplan Eco is for interior use only.
Some application examples
▪ Levelling concrete slabs or screeds based on cement, Mapecem, Mapecem Pronto, Topcem, Topcem
Pronto, anhydrite, and magnesite, including those with embedded underfloor heating systems.
▪ Levelling existing cement, terrazzo, ceramic, and natural stone floors.

TECHNICAL CHARACTERISTICS
Ultraplan Eco is a grey powder consisting of special cement with rapid setting and hydration, selected graded
silica sand, resins and special admixtures, prepared according to a formula developed in the MAPEI Research
Laboratories.
Mixed with water, Ultraplan Eco becomes a highly fluid and easily workable mortar, with perfect self-levelling
capacity, high adhesion to the substrate, and ultra-rapid drying.
Ultraplan Eco can be applied with an automatic pressure pump for distances over 100 m.
Ultraplan Eco can be spread in thicknesses up to 10 mm per coat without shrinkage, cracking or crazing, and
develops very high compressive and flexural strength, as well as resistance to indentation and abrasion.
Ultraplan Eco is ready to receive flooring after approximately after 3 hours in case of ceramic tiles and 12 hours
in case of resilient and wood flooring.
Ultraplan Eco has very low emissions of volatile organic compounds (EMICODE EC1 Plus).

RECOMMENDATIONS
▪ Do not add more water to the mix once it starts to set.
▪ Do not add lime, cement, or gypsum to the mix.
▪ Do not use Ultraplan Eco for exterior applications.
▪ Do not use Ultraplan Eco on substrates subject to continuous rising damp.
▪ If a coat of Ultraplan Contract needs to be applied once the preceding one is completely dry, first apply a
suitable
acrylic primer (such as Eco Prim T Plus or Primer G).
▪ Do not apply Ultraplan Eco at temperatures below +5°C.
▪ Do not apply Ultraplan Eco in thicknesses less than 3 mm when wooden flooring needs to be installed.

APPLICATION PROCEDURE
Preparation of the substrate
Substrates must comply with the specifications contained in the locally applicable standards.
Substrates must be sound and free of all traces of dust, loose or detached parts, varnish, wax, oil, rust, and
gypsum. Cement-based surfaces that are not sufficiently sound must be removed or, where possible,
consolidated with a suitable MAPEI system (such as Prosfas, Eco Prim PU 1K, or Primer MF).
Repair any cracks in the substrate with Eporip or Eporip SCR.
Treat dusty or particularly porous concrete surfaces with a suitable primer such as Primer G (diluted 1:1 with
water) or Eco Prim T Plus (diluted up to 1:4 with water) to hold the dust and even out the absorbency of the
substrate.
Anhydrite screeds may be levelled off with Ultraplan Eco only after having sanded the surface and having
applied a suitable primer (such as Primer G undiluted or Eco Prim T Plus diluted up to 1:2 with water).
Prime existing ceramic and natural stone surfaces with a coat of Eco Prim T Plus or Eco Prim Grip after
cleaning the surface with a suitable detergent and, if required, abrading the surface mechanically.
Preparation of the mix
While mixing with a low-speed mixer, pour in a container containing approximately 5.6 l of clean water a 23
kg-bag of Ultraplan Eco to obtain a homogeneous and lump-free mix. Larger quantities can be prepared in
suitable mixers.
After 2-3 minutes of rest, the mix should be re-stirred, and then it is ready for use.
It is recommended to add approximately 20-30% of quartz with a grain size of 0.4 or 0.8 mm when Ultraplan
Eco is used for thicknesses greater than 10 mm (max. 20 mm). For further information, consult MAPEI
Technical Services Department.
Make sure to prepare a quantity of Ultraplan Eco that can be applied within 20-30 minutes (at +23°C).
Spreading the mix
Apply Ultraplan Eco in a single coat from 1 to 10 mm with a large metal trowel or rake by keeping the trowel
slightly inclined to obtain the desired thickness.
Ultraplan Eco can also be applied with an automatic pressure pump for renders.
Due to its remarkable self-levelling properties, Ultraplan Eco immediately loses small imperfections (trowel
marks, etc.).
When the second coat of Ultraplan Eco is required, it is recommended to apply it as soon as the first one is set
to light foot traffic (approximately 3 hours at +23°C).
Ultraplan Eco is ready to receive ceramic coverings and natural stone coverings, as long as stable and not
sensitive to moisture, after approximately 3 hours. In the case of resilient and wood flooring, 12 hours are
needed (the time can vary, depending on the room temperature and humidity).

CLEANING
While still wet, Ultraplan Eco can be removed from tools with water.

CONSUMPTION
1.6 kg/m² per mm of thickness.
 PACKAGING
Ultraplan Eco is available in 23 kg bags.

STORAGE
Ultraplan Eco stored in a dry place is stable for at least 12 months. A long storage period may extend the
setting time of Ultraplan Eco, but it does not affect its final performance.

SAFETY INSTRUCTIONS FOR PREPARATION AND APPLICATION

Keep out of the reach of children.
Keep children away from fresh adhesive or installation material.
Ensure good ventilation during and after use and drying.
Do not eat, drink or smoke when using this product.
In case of contact with skin or eyes, rinse immediately with plenty of water.
Do not allow product to reach sewage system, water course or soil.
Clean tools with soap and water immediately after use.
Give only empty containers to recycling.
Dried product residues may be disposed of as domestic waste if allowed by local regulation.
Product preservative-free.
For information for allergic people or the technical data sheet, please call:
+39/02/37673.1
Always wear safety glasses.
If product gets into contact with your eyes rinse immediately with plenty of water and see an ophthalmologist.
Always wear heavy-duty waterproof gloves to protect your hands.
Always wear long trousers.
Avoid prolonged skin contact with the product.
Rinse affected areas immediately with plenty of water.
The longer fresh product remains on your skin the greater the risk of severe skin damage.
The product contains:
Binders, Mineral fillers, pigment, additive (Vdl-RL 01/May 2019).
Instructions for the safe use of our products can be found on the latest version of the SDS available on our
website www.mapei.com.
PRODUCT FOR PROFESSIONAL USE.

TECHNICAL DATA (typical values)

In compliance with the following standards: – European EN 13813 CT-C25-F7-A2FL-S1

PRODUCT IDENTITY

Consistency: fine powder

Colour: grey

Bulk density: 1300 kg/m³

EMICODE: EC1 Plus – very low emission

Blauer Engel: DE-UZ 113

 APPLICATION DATA (at +23°C - 50% R.H.)

Mixing ratio: 24-25 parts of water per 100 parts by weight of

Ultraplan Eco
Thickness per coat: from 1 to 10 mm

Self-levelling: yes

Density of mix: 2000 kg/m³

pH of mix: approx. 12

Application temperature: from +5°C to +35°C

Pot life: 20-30 min

Setting time: 45-60 min

Set to light foot traffic: min. 3 h

Waiting time before bonding:
- ceramics: min. 3 h
- resilients and wood flooring: min. 12 h

FINAL PERFORMANCE
Compressive strength:
after 1 day: 12 N/mm²
after 3 days: 17 N/mm²
after 7 days: 20 N/mm²
after 28 days: 26 N/mm²
Flexural strength:
after 1 day: 3 N/mm²
after 3 days: 4 N/mm²
after 7 days: 5 N/mm²
after 28 days: 7 N/mm²
Abrasion resistance - Taber abrader (H 22 disk -
500 g - 200 revs), expressed as loss of weight:
after 7 days:
after 28 days: 2.8 g
2.3 g
Brinell hardness:
after 1 day: 55 N/mm²
after 3 days: 70 N/mm²
after 7 days: 80 N/mm²
after 28 days: 100 N/mm²

WARNING
Although the technical details and recommendations contained in this product data sheet correspond to the
best of our knowledge and experience, all the above information must, in every case, be taken as merely
indicative and subject to confirmation after long-term practical application; for this reason, anyone who
intends to use the product must ensure beforehand that it is suitable for the envisaged application.
Please refer to the current version of the Technical Data Sheet, available from our website
www.mapei.com
 LEGAL NOTICE
The contents of this Technical Data Sheet ("TDS") may be copied into another project-related document,
but the resulting document shall not supplement or replace requirements per the TDS in force at the
time of the MAPEI product installation. The most up-to-date TDS can be downloaded from our website
www.mapei.com.
ANY ALTERATION TO THE WORDING OR REQUIREMENTS CONTAINED OR DERIVED FROM THIS TDS
EXCLUDES THE RESPONSIBILITY OF MAPEI.

513-6-2023 en (IT)

. Any reproduction of texts, photos and illustrations published here is prohibited and subject to .
prosecution