Radial Leaded Ceramic Disc Capacitors

Safety Standard Recognized, C700, Encapsulated,

KJN Type, X1 440/760 VAC/Y1 250/400/500 VAC (Industrial Grade)
Overview
KEMET’s C700, encapsulated radial leaded ceramic disc capacitor fail, but could result in a risk of fire. The class Y
capacitors are specifically designed for interference- capacitor is primarily used in line-to-ground (line by-pass)
suppression AC line filtering applications. Having applications. In this application, failure of the capacitor could
internationally recognized safety certifications, these lead to danger of electric shock.
capacitors are well-suited for applications that require
keeping potentially disruptive or damaging line transients With a working voltage of 440/760 VAC in line-to-line
and EMI out of susceptible equipment. They are also an (Class X) and 250/400/500 VAC in line-to-ground (Class Y)
ideal solution when needing to suppress line disturbances applications, these safety capacitors meet the impulse test
at the source. criteria outlined in IEC Standard 60384. Meeting subclass X1
and Y1 requirements, these devices are certified to withstand
Safety Certified Capacitors are classified as either X and/or impulses up to 4 KV (X1) and 8 KV (Y1) respectively. These
Y capacitors. Class X capacitors are primarily used in line- encapsulated devices also meet the flame test requirements
to-line (across-the-line) applications. In this application, outlined in UL Standard 94 V-0.
there is no danger of electric shock to humans should the

Benefits
• Safety standard recognized (IEC 60384-14)
• Reliable operation up to 125°C
• Class X1 440/760 VAC/ Y1 250/400/500 VAC
• 10mm and 12.5 mm lead spacing
• Lead(Pb)-free and RoHS Compliant
• Halogen-free
• Capacitance offerings ranging from 8 pF – 4.7 nF
• Available capacitance tolerances of ±5%, ±10%, and ±20%
• High-reliability
• Preformed (crimped) or straight lead configurations
• Non-polar device, minimizing installation concerns
• 100% pure matte tin-plated lead finish, allowing for
excellent solderability
• Encapsulation meets flammability standard UL 94 V-0

Applications
Typical applications include:
• Line-to-line (Class X) filtering
• Line-to-ground (Class Y) filtering
• Antenna coupling
• Primary and secondary coupling (switching power supplies)
• Line disturbances suppression (motors and motor controls, relays, switching power supplies and invertors)
Built Into Tomorrow
© KEMET Electronics Corporation • One East Broward Boulevard C1104_KJN • 8/22/2023 1
Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com
Radial Leaded Ceramic Disc Capacitors
Safety Standard Recognized, C700, Encapsulated, KJN Type, X1 440/760 VAC/Y1 250/400/500 VAC (Industrial Grade)

Ordering Information

C7 7 1 U 472 M S W D A A 7301
Ceramic Body Lead Capacitance Capacitance Rated Dielectric/ Lead Failure Packaging
Spec. Design
Series Diameter Spacing 1,2 Code (pF) Tolerance Voltage Temp. Char. Configuration 2 Rate (C-Spec)
C7 = 2 = 9.0 mm 1 = 10.0 mm U= Two J = ±5% S = X1 S = SL D= A = Straight A= See
Ceramic 3 = 10.0 mm 2 = 12.5 mm Safety significant K = ±10% 440 Y = Y5P Disc B = Vertical N/A "Packaging
700 4 = 11.0 mm digits and M = ±20% VAC/ W = Y5U Kink C-Spec
5 = 12.0mm Number of Y1 400 V = Y5V C = Outside Ordering
6 = 13.0 mm zeroes VAC Kink Options
7 = 14.0 mm T = X1 D = Inside Table"
8 = 15.0 mm 440 Kink below
VAC/
Y1 250
VAC
W = X1
760
VAC/
Y1 500
VAC

1
Capacitor body diameter will limit available lead spacing and packaging options. See "Dimensions" and "Product Ordering Codes and Ratings" sections
of this document to determine availability.
2
Bulk packaging lead length availability is dependent upon "Lead Configuration" and "Lead Spacing." See "Dimensions" section of this document to
verify availability of a specific lead length option. For nonstandard lead length inquiries, please contact KEMET.

Packaging C-Spec Ordering Options Table

Lead Length Packaging

Packaging Type
(mm)2,3 Ordering Code (C-Spec)
Reel 7301
See Note 2
Ammo Pack 7317

3.5 ±1.0 WL35

Bulk Bag 5.0 ±1.0 WL50

25.0 mm Minimum WL25

1
For nonstandard lead length inquiries, please contact KEMET.
2
Lead length for ammo and reel pack packaging is defined by the H and H0 dimensions in Table 3.

© KEMET Electronics Corporation • One East Broward Boulevard C1104_KJN • 8/22/2023 2

Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com
Radial Leaded Ceramic Disc Capacitors
Safety Standard Recognized, C700, Encapsulated, KJN Type, X1 440/760 VAC/Y1 250/400/500 VAC (Industrial Grade)

Lead Configurations

Straight Vertical Kink Outside Kink Inside Kink1

D Maximum T Maximum D Maximum T Maximum D Maximum T Maximum D Maximum T Maximum

e
4.0 5.0 5.0
Maximum Maximum Maximum

L
Ød Ød L Ød L Ød L
F F F F

All lead configurations are available on devices with lead spacing of 10 mm and 12.5 mm.

Dimensions – Millimeters

F D T e Ød
Lead Lead
Lead
Configuration Lead Spacing Body Body Lead Lead
Configuration
Ordering Code1 Spacing2 Tolerance Diameter2 Thickness Meniscus Diameter

Straight A

Vertical Kink
B
(Preformed) See Table 1 - "Product Ordering 3.0
10, 12.5 ±1.0 0.60 ±0.1
Outside Kink Codes and Ratings" maximum
C
(Preformed)
Inside Kink
D
(Preformed)
1
Lead Configuration is identified in the 13th character of the ordering code. See "Lead Configuration" and "Ordering Information" sections of this
document for further details.
2
Body diameter of capacitor will limit available lead spacing and packaging options. See "Product Ordering Codes and Ratings" sections of this
document for further details.

© KEMET Electronics Corporation • One East Broward Boulevard C1104_KJN • 8/22/2023 3

Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com
Radial Leaded Ceramic Disc Capacitors
Safety Standard Recognized, C700, Encapsulated, KJN Type, X1 440/760 VAC/Y1 250/400/500 VAC (Industrial Grade)

Approval Standard and Certification No.

Safety Standard Standard No. Subclass Working Voltage Certificate No.

X1 440 VAC
TUV IEC 60384-14 R50466900
Y1 250 VAC
X1 440 VAC
TUV IEC 60384-14 R50466900
Y1 400 VAC
X1 760 VAC
TUV IEC 60384-14 R50466900
Y1 500 VAC

UL UL 60384-14 and X1 440 VAC

E356389
CAN/CSA E60384-14 Y1 250 VAC

UL UL 60384-14 and X1 440 VAC

E356389
CAN/CSA E60384-14 Y1 400 VAC

UL UL 60384-14 and X1 760 VAC

E356389
CAN/CSA E60384-14 Y1 500 VAC
These devices are TUV and UL recognized for antenna coupling and AC line-to-line (Class X) and line-to-ground (Class Y) applications per IEC60384-14
and UL 60384-14.

Environmental Compliance
These devices are Halogen-free and RoHS Compliant. They meet all requirements set forth by both EU and China RoHS
directives.

© KEMET Electronics Corporation • One East Broward Boulevard C1104_KJN • 8/22/2023 4

Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com
Radial Leaded Ceramic Disc Capacitors
Safety Standard Recognized, C700, Encapsulated, KJN Type, X1 440/760 VAC/Y1 250/400/500 VAC (Industrial Grade)

Table 1A – Product Ordering Codes and Ratings - X1 440 Y1 400

Dimensions (mm)
Dielectric/ KEMET Capacitance
Capacitance Body Diameter Body Thickness Lead Spacing
Temp. Char. Part Number Tolerance Lead Diameter
(Maximum) (Maximum)
C72(1)U080JSSD(2)A(3) 8 pF
C72(1)U100JSSD(2)A(3) 10 pF
9.0
C72(1)U150JSSD(2)A(3) 15 pF
C72(1)U220JSSD(2)A(3) 22 pF
SL C73(1)U330JSSD(2)A(3) 33 pF ±5%
10.0
C73(1)U390JSSD(2)A(3) 39 pF
C74(1)U470JSSD(2)A(3) 47 pF
11.0
C74(1)U560JSSD(2)A(3) 56 pF
C75(1)U680JSSD(2)A(3) 68 pF 12.0
C72(1)U080KSSD(2)A(3) 8 pF
C72(1)U100KSSD(2)A(3) 10 pF
9.0
C72(1)U150KSSD(2)A(3) 15 pF
C72(1)U220KSSD(2)A(3) 22 pF
SL C73(1)U330KSSD(2)A(3) 33 pF ±10%
10.0
C73(1)U390KSSD(2)A(3) 39 pF
C74(1)U470KSSD(2)A(3) 47 pF
11.0
C74(1)U560KSSD(2)A(3) 56 pF
C75(1)U680KSSD(2)A(3) 68 pF 12.0
C72(1)U080KSYD(2)A(3) 8 pF
C72(1)U100KSYD(2)A(3) 10 pF
C72(1)U150KSYD(2)A(3) 15 pF
C72(1)U220KSYD(2)A(3) 22 pF
C72(1)U330KSYD(2)A(3) 33 pF
C72(1)U390KSYD(2)A(3) 39 pF
C72(1)U470KSYD(2)A(3) 47 pF
10.0 mm
C72(1)U560KSYD(2)A(3) 56 pF 6.0 0.60 ± 0.1
12.5 mm
C72(1)U680KSYD(2)A(3) 68 pF
9.0
C72(1)U101KSYD(2)A(3) 100 pF
Y5P C72(1)U151KSYD(2)A(3) 150 pF ±10%
C72(1)U181KSYD(2)A(3) 180 pF
C72(1)U221KSYD(2)A(3) 220 pF
C72(1)U331KSYD(2)A(3) 330 pF
C72(1)U361KSYD(2)A(3) 360 pF
C72(1)U391KSYD(2)A(3) 390 pF
C72(1)U421KSYD(2)A(3) 420 pF
C72(1)U471KSYD(2)A(3) 470 pF
C73(1)U561KSYD(2)A(3) 560 pF
10.0
C73(1)U681KSYD(2)A(3) 680 pF
C75(1)U102KSYD(2)A(3) 1000 pF 12.0
C72(1)U102MSWD(2)A(3) 1000 pF 9.0
C74(1)U152MSWD(2)A(3) 1500 pF 11.0
C75(1)U222MSWD(2)A(3) 2200 pF 12.0
Y5U ±20%
C77(1)U332MSWD(2)A(3) 3300 pF 14.0
C78(1)U392MSWD(2)A(3) 3900 pF 15.0
C78(1)U472MSWD(2)A(3) 4700 pF 15.0
C72(1)U102MSVD(2)A(3) 1000 pF 9.0
C72(1)U152MSVD(2)A(3) 1500 pF 9.0
C73(1)U222MSVD(2)A(3) 2200 pF 10.0
Y5V ±20%
C75(1)U332MSVD(2)A(3) 3300 pF 12.0
C76(1)U392MSVD(2)A(3) 3900 pF 13.0
C77(1)U472MSVD(2)A(3) 4700 pF 14.0
Dielectric/ KEMET Capacitance Body Diameter Body Thickness
Capacitance Lead Diameter Lead Spacing
Temp. Char. Part Number Tolerance (Maximum) (Maximum)

(1) To properly complete ordering code, insert the one-digit numeric code to reflect required lead spacing: (Note that select capacitance values and packaging
options may limit lead spacing availability. See table above to verify availability.)
1 = 10.0 mm
2 = 12.5 mm
(2) To properly complete ordering code, insert the one-digit character code to reflect the required lead configuration: (See "Lead Configuration" section of this
document, page 2, for further details.)
A = Straight
B = Vertical Kink
C = Outside Kink
D = Inside Kink
(3) To properly complete ordering code, enter the four-digit numeric or alphanumeric "Packaging C-Spec Ordering Code." See "Dimensions" section of this
document, page 2, for available options.

© KEMET Electronics Corporation • One East Broward Boulevard C1104_KJN • 8/22/2023 5

Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com
Radial Leaded Ceramic Disc Capacitors
Safety Standard Recognized, C700, Encapsulated, KJN Type, X1 440/760 VAC/Y1 250/400/500 VAC (Industrial Grade)

Table 1B – Product Ordering Codes and Ratings - X1 440 Y1 250

Dimensions (mm)
Dielectric/ KEMET Capacitance
Capacitance Body Diameter Body Thickness Lead Spacing
Temp. Char. Part Number Tolerance Lead Diameter
(Maximum) (Maximum)
C72(1)U080JTSD(2)A(3) 8 pF
C72(1)U100JTSD(2)A(3) 10 pF
9.0
C72(1)U150JTSD(2)A(3) 15 pF
C72(1)U220JTSD(2)A(3) 22 pF
SL C73(1)U330JTSD(2)A(3) 33 pF ±5%
10.0
C73(1)U390JTSD(2)A(3) 39 pF
C74(1)U470JTSD(2)A(3) 47 pF
11.0
C74(1)U560JTSD(2)A(3) 56 pF
C75(1)U680JTSD(2)A(3) 68 pF 12.0
C72(1)U080KTSD(2)A(3) 8 pF
C72(1)U100KTSD(2)A(3) 10 pF
9.0
C72(1)U150KTSD(2)A(3) 15 pF
C72(1)U220KTSD(2)A(3) 22 pF
SL C73(1)U330KTSD(2)A(3) 33 pF ±10%
10.0
C73(1)U390KTSD(2)A(3) 39 pF
C74(1)U470KTSD(2)A(3) 47 pF
11.0
C74(1)U560KTSD(2)A(3) 56 pF
C75(1)U680KTSD(2)A(3) 68 pF 12.0
C72(1)U080KTYD(2)A(3) 8 pF
C72(1)U100KTYD(2)A(3) 10 pF
C72(1)U150KTYD(2)A(3) 15 pF
C72(1)U220KTYD(2)A(3) 22 pF
C72(1)U330KTYD(2)A(3) 33 pF
C72(1)U390KTYD(2)A(3) 39 pF
C72(1)U470KTYD(2)A(3) 47 pF
10.0 mm
C72(1)U560KTYD(2)A(3) 56 pF 6.0 0.60 ± 0.1
12.5 mm
C72(1)U680KTYD(2)A(3) 68 pF
9.0
C72(1)U101KTYD(2)A(3) 100 pF
Y5P C72(1)U151KTYD(2)A(3) 150 pF ±10%
C72(1)U181KTYD(2)A(3) 180 pF
C72(1)U221KTYD(2)A(3) 220 pF
C72(1)U331KTYD(2)A(3) 330 pF
C72(1)U361KTYD(2)A(3) 360 pF
C72(1)U391KTYD(2)A(3) 390 pF
C72(1)U421KTYD(2)A(3) 420 pF
C72(1)U471KTYD(2)A(3) 470 pF
C73(1)U561KTYD(2)A(3) 560 pF
10.0
C73(1)U681KTYD(2)A(3) 680 pF
C75(1)U102KTYD(2)A(3) 1000 pF 12.0
C72(1)U102MTWD(2)A(3) 1000 pF 9.0
C74(1)U152MTWD(2)A(3) 1500 pF 11.0
C75(1)U222MTWD(2)A(3) 2200 pF 12.0
Y5U ±20%
C77(1)U332MTWD(2)A(3) 3300 pF 14.0
C78(1)U392MTWD(2)A(3) 3900 pF 15.0
C78(1)U472MTWD(2)A(3) 4700 pF 15.0
C72(1)U102MTVD(2)A(3) 1000 pF 9.0
C72(1)U152MTVD(2)A(3) 1500 pF 9.0
C73(1)U222MTVD(2)A(3) 2200 pF 10.0
Y5V ±20%
C75(1)U332MTVD(2)A(3) 3300 pF 12.0
C76(1)U392MTVD(2)A(3) 3900 pF 13.0
C77(1)U472MTVD(2)A(3) 4700 pF 14.0
Dielectric/ KEMET Capacitance Body Diameter Body Thickness
Capacitance Lead Diameter Lead Spacing
Temp. Char. Part Number Tolerance (Maximum) (Maximum)

(1) To properly complete ordering code, insert the one-digit numeric code to reflect required lead spacing: (Note that select capacitance values and packaging
options may limit lead spacing availability. See table above to verify availability.)
1 = 10.0 mm
2 = 12.5 mm
(2) To properly complete ordering code, insert the one-digit character code to reflect the required lead configuration: (See "Lead Configuration" section of this
document, page 2, for further details.)
A = Straight
B = Vertical Kink
C = Outside Kink
D = Inside Kink
(3) To properly complete ordering code, enter the four-digit numeric or alphanumeric "Packaging C-Spec Ordering Code." See "Dimensions" section of this
document, page 2, for available options.

© KEMET Electronics Corporation • One East Broward Boulevard C1104_KJN • 8/22/2023 6

Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com
Radial Leaded Ceramic Disc Capacitors
Safety Standard Recognized, C700, Encapsulated, KJN Type, X1 440/760 VAC/Y1 250/400/500 VAC (Industrial Grade)

Table 1C – Product Ordering Codes and Ratings - X1 760 Y1 500

Dimensions (mm)
Dielectric/ KEMET Capacitance
Capacitance Body Diameter Body Thickness Lead Spacing
Temp. Char. Part Number Tolerance Lead Diameter
(Maximum) (Maximum)
C72(1)U100JWSD(2)A(3) 10 pF
C72(1)U150JWSD(2)A(3) 15 pF 9.0
C72(1)U220JWSD(2)A(3) 22 pF
C73(1)U330JWSD(2)A(3) 33 pF
±5% 10.0
C73(1)U390JWSD(2)A(3) 39 pF
C74(1)U470JWSD(2)A(3) 47 pF
11.0
C74(1)U560JWSD(2)A(3) 56 pF
C75(1)U680JWSD(2)A(3) 68 pF 12.0
SL
C72(1)U100KWSD(2)A(3) 10 pF
C72(1)U150KWSD(2)A(3) 15 pF 9.0
C72(1)U220KWSD(2)A(3) 22 pF
C73(1)U330KWSD(2)A(3) 33 pF
±10% 10.0
C73(1)U390KWSD(2)A(3) 39 pF
C74(1)U470KWSD(2)A(3) 47 pF
11.0
C74(1)U560KWSD(2)A(3) 56 pF
C75(1)U680KWSD(2)A(3) 68 pF 12.0
C72(1)U100KWYD(2)A(3) 10 pF
10.0 mm
C72(1)U150KWYD(2)A(3) 15 pF 6.0 0.60 ± 0.1
12.5 mm
C72(1)U220KWYD(2)A(3) 22 pF
C72(1)U330KWYD(2)A(3) 33 pF
C72(1)U390KWYD(2)A(3) 39 pF
C72(1)U470KWYD(2)A(3) 47 pF
C72(1)U560KWYD(2)A(3) 56 pF
C72(1)U680KWYD(2)A(3) 68 pF
9.0
C72(1)U101KWYD(2)A(3) 100 pF
Y5P C72(1)U151KWYD(2)A(3) 150 pF ±10%
C72(1)U181KWYD(2)A(3) 180 pF
C72(1)U221KWYD(2)A(3) 220 pF
C72(1)U331KWYD(2)A(3) 330 pF
C72(1)U361KWYD(2)A(3) 360 pF
C72(1)U391KWYD(2)A(3) 390 pF
C72(1)U471KWYD(2)A(3) 470 pF
C73(1)U561KWYD(2)A(3) 560 pF
10.0
C73(1)U681KWYD(2)A(3) 680 pF
C75(1)U102KWYD(2)A(3) 1000 pF 12.0
Dielectric/ KEMET Capacitance Body Diameter Body Thickness
Capacitance Lead Diameter Lead Spacing
Temp. Char. Part Number Tolerance (Maximum) (Maximum)

(1) To properly complete ordering code, insert the one-digit numeric code to reflect required lead spacing: (Note that select capacitance values and packaging
options may limit lead spacing availability. See table above to verify availability.)
1 = 10.0 mm
2 = 12.5 mm
(2) To properly complete ordering code, insert the one-digit character code to reflect the required lead configuration: (See "Lead Configuration" section of this
document, page 2, for further details.)
A = Straight
B = Vertical Kink
C = Outside Kink
D = Inside Kink
(3) To properly complete ordering code, enter the four-digit numeric or alphanumeric "Packaging C-Spec Ordering Code." See "Dimensions" section of this
document, page 2, for available options.

© KEMET Electronics Corporation • One East Broward Boulevard C1104_KJN • 8/22/2023 7

Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com
Radial Leaded Ceramic Disc Capacitors
Safety Standard Recognized, C700, Encapsulated, KJN Type, X1 440/760 VAC/Y1 250/400/500 VAC (Industrial Grade)

Table 1C – Product Ordering Codes and Ratings - X1 760 Y1 500 cont.

Dimensions (mm)
Dielectric/ KEMET Capacitance
Capacitance Body Diameter Body Thickness Lead Spacing
Temp. Char. Part Number Tolerance Lead Diameter
(Maximum) (Maximum)
C72(1)U221KWWD(2)A(3) 220 pF
C72(1)U331KWWD(2)A(3) 330 pF
C72(1)U471KWWD(2)A(3) 470 pF 9.0
C72(1)U681KWWD(2)A(3) 680 pF
C72(1)U102KWWD(2)A(3) 1000 pF
Y5U C74(1)U152KWWD(2)A(3) 1500 pF ±10% 11.0
C75(1)U222KWWD(2)A(3) 2200 pF
12.0
C75(1)U272KWWD(2)A(3) 2700 pF
C77(1)U332KWWD(2)A(3) 3300 pF 14.0
C78(1)U392KWWD(2)A(3) 3900 pF
15.0
C78(1)U472KWWD(2)A(3) 4700 pF 10.0 mm
6.0 0.60 ± 0.1
C72(1)U221MWWD(2)A(3) 220 pF 12.5 mm
C72(1)U331MWWD(2)A(3) 330 pF
C72(1)U471MWWD(2)A(3) 470 pF 9.0
C72(1)U681MWWD(2)A(3) 680 pF
C72(1)U102MWWD(2)A(3) 1000 pF
Y5U C74(1)U152MWWD(2)A(3) 1500 pF ±20% 11.0
C75(1)U222MWWD(2)A(3) 2200 pF
12.0
C75(1)U272MWWD(2)A(3) 2700 pF
C77(1)U332MWWD(2)A(3) 3300 pF 14.0
C78(1)U392MWWD(2)A(3) 3900 pF
15.0
C78(1)U472MWWD(2)A(3) 4700 pF
Dielectric/ KEMET Capacitance Body Diameter Body Thickness
Capacitance Lead Diameter Lead Spacing
Temp. Char. Part Number Tolerance (Maximum) (Maximum)

(1) To properly complete ordering code, insert the one-digit numeric code to reflect required lead spacing: (Note that select capacitance values and packaging
options may limit lead spacing availability. See table above to verify availability.)
1 = 10.0 mm
2 = 12.5 mm
(2) To properly complete ordering code, insert the one-digit character code to reflect the required lead configuration: (See "Lead Configuration" section of this
document, page 2, for further details.)
A = Straight
B = Vertical Kink
C = Outside Kink
D = Inside Kink
(3) To properly complete ordering code, enter the four-digit numeric or alphanumeric "Packaging C-Spec Ordering Code." See "Dimensions" section of this
document, page 2, for available options.

© KEMET Electronics Corporation • One East Broward Boulevard C1104_KJN • 8/22/2023 8

Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com
Radial Leaded Ceramic Disc Capacitors
Safety Standard Recognized, C700, Encapsulated, KJN Type, X1 440/760 VAC/Y1 250/400/500 VAC (Industrial Grade)

Table 2 – Performance & Reliability: Test Methods and Conditions

Item Specification Test Method
Operating Temperature Range −40°C to +125°C
Between lead The capacitor shall not be damaged when 4,000 VAC (rms) is
No failures
wires applied between the lead wires for 60 seconds.
The terminals (leads) of the capacitor shall
be connected together. A metal foil is tightly
wrapped around the body of the capacitor
Dielectric at a distance of about 3 to 4 mm from each
Strength terminal. The capacitor is then inserted
Body Insulation No failures Metal
about
into a container filled with metal balls Foil
3 to 4 mm
approximately 1 mm in diameter. 4,000 VAC
(rms) is applied for 60 seconds between the Metal
Balls
capacitor lead wires and metal balls.
(charge/discharge current ≤ 50 mA)
The insulation resistance shall be measured with 500 ±50 VDC
Insulation Resistance (IR) 10,000 MΩ minimum applied after 60 ±5 seconds of charging.
Capacitance Within specified tolerance

Temperature Characteristic Frequency Voltage

Specification
Characteristics
SL 1 MHz ±20%
Dissipation Factor (DF) or Q Y5P DF ≤ 2.5% 5.0 Vrms Maximum
Y5P /Y5U/Y5V 1 MHz ±20%
Y5U/Y5V DF ≤ 5.0%
The measurement at reference temperature 25°C
SL Q ≥ 300
A capacitance measurement is made at each step specified:
Step Temperature
Temperature Capacitance 1 +25 ±2°C
Characteristics Change
2 Minimum operating temperature
Temperature Characteristics Y5P Within ±10% 3 +25 ±2°C
Y5U Within +22%/−56% 4 Maximum operating temperature
Y5V Within +22%/−82% 5 +25 ±2°C
SL +350~1,000% Pretreatment:
Capacitor is stored at 85 ±2°C for 1 hour and then placed at room
condition1 for 24 ±2 hours before measurement.
With the termination in its normal position, the specimen is held
Lead wire or capacitor body shall by its body in such a manner that the axis of the termination is
Tensile vertical. A tensile force of 10 N is applied to the termination in the
not break. direction of its axis and acting in a direction away from the body
of the specimen.
With the termination in its normal position, the specimen is held
Terminal by its body in such a manner that the axis of the termination is
Strength vertical; a mass force of 5 N is then suspended from the end of
Lead wire or capacitor body shall the termination. The body of the specimen is then inclined within
Bending a period of 2 to 3 seconds, through an angle of approximately 90°
not break. in the vertical plane and then resumed to its initial position over
the same period of time; this operation constitutes one bend.
One bend immediately followed by a second bend in the opposite
direction.
1
“Room Condition” is defined as follows: Temperature: 20 ~ 35°C/Humidity: 45 ~ 75%/Atmospheric Pressure: 86 ~ 106 kPa.

© KEMET Electronics Corporation • One East Broward Boulevard C1104_KJN • 8/22/2023 9

Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com
Radial Leaded Ceramic Disc Capacitors
Safety Standard Recognized, C700, Encapsulated, KJN Type, X1 440/760 VAC/Y1 250/400/500 VAC (Industrial Grade)

Table 2 – Performance & Reliability: Test Methods and Conditions cont.

Item Specification Test Method
Appearance No visual defect As shown in the figure below, the lead wires are immersed in
molten solder up to 1.5 mm (+5/−0 mm) from the end of the
epoxy meniscus (root of lead wire).
IR 1,000 MΩ Minimum Duration/Solder Temperature: 3.5 ±0.5 seconds/350°C ±10°C
or 10 ±1 seconds/260°C ±5°C
Dielectric
Per item 1 Thermal
Strength Capacitor
Screen
Soldering Effect 1.5 to
(Non-Preheat) Within ±10% 2.0 mm
Molten
Y5P, Y5U and Y5V: within ±10% Solder
Capacitance
Pretreatment: Capacitor is stored at 85°C ±2°C for 1 hour and
SL: within ±2.5% or ±0.25 pF, then placed at room condition1 for 24 ±2 hours before initial
whichever is larger measurements.
Post-treatment: Capacitor is stored for 1 to 2 hours at room
condition1.
Appearance No visual defect Steady State Humidity: Load Humidity:

Temperature Capacitance
Characteristics Change
Y5P Within ±10%
Capacitance
Y5U Within ±15% 90 to 95% humidity at 40°C
90 to 95% humidity at 40°C
Biased Y5V Within ±30% ±2°C for 500 ±12 hours with
±2°C for 500 ±12 hours. full rated voltage applied.
Humidity SL Within ±5%
Post-treatment: Post-treatment:
Capacitor is stored for 1 to 2 Capacitor is stored for 1 to 2
Y5V and Y5U: 7.5% maximum hours at room condition1.
DF hours at room condition1.
Y5P: 5% maximum
Q Q ≥ 135

IR 3,000 MΩ minimum
Dielectric
No failures
Strength
No visual defect Impulse Voltage: Each individual capacitor is subjected to three
Appearance 8 kv impulse prior to life testing.
Vp U PR Cx tr td
0.9Vp
(uF) (uS) (uS)
Voltage

U PP 0.01 1.2 46
Capacitance SL, Y5P, Y5U within ±20% 0.1 1.5 47
Change Y5V within ±30% 0.5Vp
High
Temperature
Life IR 3,000 MΩ minimum
Time
tr
td

Capacitors are placed in a circulating air oven for a period of

1,000 hours. The air in the oven is maintained at a temperature
Dielectric of 125°C ±2 throughout the test. The capacitors are subjected to
No failures
Strength 170% of Rated Voltage. Each hour the voltage is increased to AC
1,000 Vrms for 0.1 seconds.

1
“Room Condition” is defined as follows: Temperature: 20 ~ 35°C/Humidity: 45 ~ 75%/Atmospheric Pressure: 86 ~ 106 kPa.

© KEMET Electronics Corporation • One East Broward Boulevard C1104_KJN • 8/22/2023 10

Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com
Radial Leaded Ceramic Disc Capacitors
Safety Standard Recognized, C700, Encapsulated, KJN Type, X1 440/760 VAC/Y1 250/400/500 VAC (Industrial Grade)

Table 2 – Performance & Reliability: Test Methods and Conditions cont.

Item Specification Test Method

The capacitor is exposed to a flame for 15 seconds and then
The capacitor flame extinguishes as removed for 15 seconds. This test is repeated for 5 cycles.
follows:
Capacitor

Flame
Cycle Time 76
Flame Test 30 seconds 38
1~4 127
maximum
60 seconds Gas Burner
5
maximum
20º (Unit:mm)

The capacitors are individually wrapped in at least one, but not

more than two, complete layers of cheesecloth. They are then
subjected to 20 discharges. The interval between successive
discharges is 5 seconds. The VAC is maintained for 2 minutes
after the last discharge.
F L1 L2 R
S1
C1 C2 C3 CX Ct Vt
S2 Vac L3 L4
Tr

Oscilloscope
C1, 2 1 μF ±10% C3 0.033 μF ±5% 10 kV
Active Flammability The cheesecloth should not ignite.
L1-10 1.5 mH ±20% 16 A Rod core choke Cx Test capacitor
R 100 ±2% Ω VAC V R ±5%
Ct 3 μF ±5% 10 kV VR Rated Working Voltage

F Fuse, Rated 10A Vt Voltage applied to C t

Vx
5kV

time
The capacitor under test is held into a flame and in a position
which best promotes burning. Each specimen is exposed to the
flame once.
Test Specimen
About 8mm

200
45º ±5mm Tissue
The burning time should not exceed
Passive Flammability 30 seconds.
About 10mm
The tissue paper should not ignite. Thick Board

Time of Exposure to Flame: 30 seconds

Length of Flame: 12 ±1 mm
Gas Burner Length: 35 mm minimum
Inside Diameter: 0.5 ±0.1 mm
Outside Diameter: 0.9 mm maximum
Gas Butane Gas Purity: 95% minimum
1
“Room Condition” is defined as follows: Temperature: 20 ~ 35°C/Humidity: 45 ~ 75%/Atmospheric Pressure: 86 ~ 106 kPa.

© KEMET Electronics Corporation • One East Broward Boulevard C1104_KJN • 8/22/2023 11

Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com
Radial Leaded Ceramic Disc Capacitors
Safety Standard Recognized, C700, Encapsulated, KJN Type, X1 440/760 VAC/Y1 250/400/500 VAC (Industrial Grade)

Soldering and Mounting Information

Soldering:
When soldering this product to a PCB/PWB, do not exceed the solder heat resistance specification of the capacitor.
Subjecting this product to excessive heating could reflow the solder joint between the lead and ceramic element and/or may
result in thermal shocks that can crack the ceramic element.

When soldering these capacitors with a soldering iron, it should be performed under the following conditions:
• Temperature of iron-tip: 400°C maximum
• Soldering iron wattage: 50 W maximum
• Soldering time: 3.5 seconds maximum

Cleaning (ultrasonic cleaning):

To perform ultrasonic cleaning, observe the following conditions:
• Rinse bath capacity: output of 20 watts per liter or less
• Rinsing time: 5 minute maximum
• Do not vibrate the PCB/PWB directly
• Excessive ultrasonic cleaning may lead to fatigue destruction of the lead wires

Construction

Epoxy Encapsulation Detailed Cross Section

(0.2 mm Minimum Thickness,
Pigment = Blue/UL 94 V-0)

Lead Attach Solder

(Sn97/Ag3/Sn99.3/Cu0.7)

Dielectric
material
(BaTiO3)

Electrode Electrode
(Ag/Cu) (Ag/Cu)

Lead Attach Solder Lead wire

(Sn97/Ag3/Sn99.3/Cu0.7) Core Metal Steel
Dielectric
Barrier Layer Cu
material
100% Sn (BaTiO3)
Finish Layer (3-7 µm)

© KEMET Electronics Corporation • One East Broward Boulevard C1104_KJN • 8/22/2023 12

Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com
Radial Leaded Ceramic Disc Capacitors
Safety Standard Recognized, C700, Encapsulated, KJN Type, X1 440/760 VAC/Y1 250/400/500 VAC (Industrial Grade)

Marking
These capacitors shall be laser marked with KEMET's trademark, type designation, capacitor class, rated voltage, rated
capacitance, and capacitance tolerance codes. In addition, all devices are marked with the recognized approval mark and a
date/lot code for traceability. Marking will be supplied on one side of the encapsulated capacitor body. All marking shall be
legible to allow for clear identification of the component. Marking appears in legible contrast. Illustrated below is an example
of the marking format and content.

X1 440 VAC / Y1 250 VAC

KEMET
Trademark Rated Capacitance
(3 Numeric Characters)

Type Designation Capacitance Tolerance Code

(3 Characters) (1 Character)
Approval Mark UL approval mark

Date/Lot Code
(See Table Below)
Capacitor Class
and Rated Voltage

X1 440 VAC / Y1 400 VAC

KEMET
Trademark Rated Capacitance
(3 Numeric Characters)

Type Designation Capacitance Tolerance Code

(3 Characters) (1 Character)
Approval Mark UL approval mark

Date/Lot Code
(See Table Below)
Capacitor Class
and Rated Voltage

Date/Lot Code e.g., 9D (December 2019, Taiwan)

9 D -
Manufacturing
Month: Manufacturing
Last digit of year,
Location Code
e.g.,
1-9 = Jan - Sept
O = October (blank): Taiwan
3 = 2013
N = November C: Dongguan
D = December

© KEMET Electronics Corporation • One East Broward Boulevard C1104_KJN • 8/22/2023 13

Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com
Radial Leaded Ceramic Disc Capacitors
Safety Standard Recognized, C700, Encapsulated, KJN Type, X1 440/760 VAC/Y1 250/400/500 VAC (Industrial Grade)

Marking cont.
X1 760 VAC / Y1 500 VAC
KEMET
Trademark Rated Capacitance
(3 Numeric Characters)

Type Designation Capacitance Tolerance Code

(3 Characters) (1 Character)
Approval UL approval mark
Mark
Date/Lot Code
(See Table Below)
Capacitor Class
and Rated Voltage

Date/Lot Code e.g., 9D (December 2019, Taiwan)

9 D -
Manufacturing
Month: Manufacturing
Last digit of year,
Location Code
e.g.,
1-9 = Jan - Sept
O = October (blank): Taiwan
3 = 2013
N = November C: Dongguan
D = December

© KEMET Electronics Corporation • One East Broward Boulevard C1104_KJN • 8/22/2023 14

Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com
Radial Leaded Ceramic Disc Capacitors
Safety Standard Recognized, C700, Encapsulated, KJN Type, X1 440/760 VAC/Y1 250/400/500 VAC (Industrial Grade)

Packaging Quantities

Capacitor Bulk Bag (Loose)

Body Diameter
Body Diameter Lead Length Cut Lead Length
Code1
(mm) (WL25) (WL35, WL50, WL10)
7.0 0
8.0 1
9.0 2
10.0 3
11.0 4 200 pieces/bag 500 pieces/bag
12.0 5
13.0 6
14.0 7
15.0 8
16.0 9
1
The "Body Diameter Code" is located in the third character position of the ordering code. This code identifies the maximum diameter of the capacitor
body in millimeters. For more information regarding the ordering code, see "Ordering Information" section of this document.

Lead Body Pitch Body Reel Ammo

Spacing Diameter (mm) (Carrier Tape) Diameter Code (7301) Pack (7317)
≤ 12.0 12.7 0-5 2,000 pieces/reel 1,000 pieces/box
5
12.0 < D ≤ 16.0 25.4 6-9 1,000 pieces/reel 750 pieces/box
≤ 12.0 12.7 0-5 2,000 pieces/reel 1,000 pieces/box
7.5 12.0 < D ≤ 15.0 6-8 1,000 pieces/reel 750 pieces/box
25.4
≥ 16.0 9 750 pieces/reel 750 pieces/box
≤ 10 0-3 1,000 pieces/reel 1,000 pieces/box
10 25.4
≥ 11 4-9 750 pieces/reel 750 pieces/box
≤9 0-2 1,000 pieces/reel 500 pieces/box
12.5 25.4
≥ 10 3-9 500 pieces/reel 500 pieces/box

© KEMET Electronics Corporation • One East Broward Boulevard C1104_KJN • 8/22/2023 15

Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com
Radial Leaded Ceramic Disc Capacitors
Safety Standard Recognized, C700, Encapsulated, KJN Type, X1 440/760 VAC/Y1 250/400/500 VAC (Industrial Grade)

Figure 1 - Ammo/Reel Pack Taping Format

5 mm and 7.5 mm Lead Spacing: For All Lead Spacing:

P2 P D ∆S
∆h1 0 ∆h2
e
T maximum
P1 Ød W2 Marking Side
F
L W1
W0 W

P0 ℓ ØD0 t2 t1

5 mm, 7.5 mm, 10 mm and 12.5 mm Lead Spacing:

P2 P ∆S
D
e
P1
F Ød W2
H H0
L W1
W0 W

P0 ℓ ØD0

Table 3 – Ammo/Reel Pack Taping Specifications

Lead Spacing 5 mm 7.5 mm 10 mm 12.5 mm

Lead Style Straight Preformed1 Straight Preformed1 Straight Preformed1 Straight Preformed1

Item Symbol Dimensions (mm)

Lead Spacing F 5.0 ±1.0 7.5 ±1.0 10.0 ±1.0 12.5 ±1.0

Component Pitch P 12.7 ±1.0 25.4 ±2.0 12.7 ±1.0 25.4 ±2.0 12.7 ±1.0 25.4 ±2.0 12.7 ±1.0 25.4 ±2.0 25.4 ±2.0 25.4 ±2.0

Sprocket Hole Pitch P0 12.7 ±0.3 12.7 ±0.3 12.7 ±0.3 12.7 ±0.3

Sprocket Hole Center to

P2 6.35 ±1.5 12.7 ±1.5 6.35 ±1.5 12.7 ±1.5 6.35 ±1.5 12.7 ±1.5 6.35 ±1.5 12.7 ±1.5 12.7 ±1.5 12.7 ±1.5
Component Center

Sprocket Hole Center to

P1 3.85 ±0.7 10.2 ±1.5 3.85 ±0.7 10.2 ±1.5 2.6 ±0.7 8.95 ±1.5 2.6 ±0.7 8.95 ±1.5 7.7 ±1.5 6.45 ±1.5
Lead Center

Body Diameter D See "Product Ordering Codes and Ratings" section of this document.

Component Alignment
∆S 0 ±2.0
(side/side)

Carrier Tape Width W 18.0 +1.0/−0.5

Sprocket Hole Position W1 9.0 ±0.5

1
Preformed (crimped) lead configurations include vertical kink, outside kink, and inside kink. See "Lead Configurations" and "Ordering Information"
sections of this document for further details.
2
Also referred to as "lead length" in this document.

© KEMET Electronics Corporation • One East Broward Boulevard C1104_KJN • 8/22/2023 16

Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com
Radial Leaded Ceramic Disc Capacitors
Safety Standard Recognized, C700, Encapsulated, KJN Type, X1 440/760 VAC/Y1 250/400/500 VAC (Industrial Grade)

Table 3 – Ammo Pack Taping Specifications cont.

Lead Spacing 5 mm 7.5 mm 10 mm 12.5 mm

Lead Style Straight Preformed1 Straight Preformed1 Straight Preformed1 Straight Preformed1

Item Symbol Dimensions (mm)

Height to Seating Plane 2
H0 N/A 16.0 +2.0/-0 N/A 16.0 +2.0/-0 N/A 16.0 +2.0/-0 N/A 16.0 +2.0/-0
(preformed leads1)

Height to SeatingPlane 2
H 20.0 +1.5/-1.0 N/A 20.0 +1.5/-1.0 N/A 20.0 +1.5/-1.0 N/A 20.0 +1.5/-1.0 N/A
(straight leads)

Lead Protrusion ℓ 2.0 maximum

Diameter of Sprocket
D0 4.0 ±0.2
Hole

Lead Diameter φd 0.6 ±0.1

Carrier Tape Thickness t1 0.6 ±0.3

Total Thickness
(Carrier Tape, Hold- t2 1.5 maximum
Down Tape and Lead)

∆h1
Component Alignment
2.0 maximum
(front/back )
∆h2

Cut Out Length L 11.0 maximum

Hold-Down Tape Width W0 10.0 minimum

Hold-Down Tape Position W2 3.0 maximum

Coating Extension on
e 3.0 maximum for straight lead; not to exceed the bend for preformed1 lead configurations.
Leads (meniscus)

Body Thickness T 8.0 maximum

1
Preformed (crimped) lead configurations include vertical kink, outside kink, and inside kink. See "Lead Configurations" and "Ordering Information"
sections of this document for further details.
2
Also referred to as "lead length" in this document.

Application Notes:
Storage and Operating Conditions:
The Insulating coating of these devices does not form an air and moisture tight seal. Avoid exposure to moisture and do not
use or store these devices in a corrosive atmosphere, especially where chloride gas, sulfide gas, acid, alkali, salt or the like
are present. Before cleaning, bonding or molding these devices, it is important to verify that your process does not affect
product quality and performance. KEMET recommends testing and evaluating the performance of a cleaned, bonded or
molded product prior to implementing and/or qualifying any of these processes. Store the capacitors where the temperature
and relative humidity do not exceed 40 degrees centigrade and 70% respectively. For optimum solderability, capacitor stock
should be used promptly, preferably within 6 months of receipt.

Working Voltage:
Application voltage (Vp-p or Vo-p) must not exceed the voltage rating of the capacitor. Irregular voltages can be generated
for a transient period of time when voltage is initially applied and/or removed from a circuit. It is important to choose a
capacitor with a voltage rating greater than or equal to these irregular voltages.

© KEMET Electronics Corporation • One East Broward Boulevard C1104_KJN • 8/22/2023 17

Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com
Radial Leaded Ceramic Disc Capacitors
Safety Standard Recognized, C700, Encapsulated, KJN Type, X1 440/760 VAC/Y1 250/400/500 VAC (Industrial Grade)

Application Notes (cont.):

Operating Temperature and Self-Generating Heat:

The surface temperature of a capacitor should be kept below the upper limit of its rated operating temperature range. Be
sure to take into account the heat generated by the capacitor itself. When the capacitor is used in a high-frequency current,
pulse current or similar current, it may self-generate heat due to dielectric loss. Temperature rise due to self-generated
heating should not exceed 20°C (while operated at an atmosphere temperature of 25°C).

Handling - Vibration and Impact:

Do not expose these devices or their leads to excessive shock or vibration during use.

FAILURE TO FOLLOW THE ABOVE CAUTIONS MAY RESULT, WORST CASE, IN A SHORT CIRCUIT AND CAUSE FUMING OR
PARTIAL DISPERSION WHEN THE PRODUCT IS USED.

© KEMET Electronics Corporation • One East Broward Boulevard C1104_KJN • 8/22/2023 18

Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com
Radial Leaded Ceramic Disc Capacitors
Safety Standard Recognized, C700, Encapsulated, KJN Type, X1 440/760 VAC/Y1 250/400/500 VAC (Industrial Grade)

KEMET Electronics Corporation Sales Offices

For a complete list of our global sales offices, please visit www.kemet.com/sales.

Disclaimer
All product specifications, statements, information and data (collectively, the “Information”) in this datasheet are subject to change. The customer is responsible for
checking and verifying the extent to which the Information contained in this publication is applicable to an order at the time the order is placed. All Information given
herein is believed to be accurate and reliable, but it is presented without guarantee, warranty, or responsibility of any kind, expressed or implied.

Statements of suitability for certain applications are based on KEMET Electronics Corporation’s (“KEMET”) knowledge of typical operating conditions for such
applications, but are not intended to constitute – and KEMET specifically disclaims – any warranty concerning suitability for a specific customer application or use.
The Information is intended for use only by customers who have the requisite experience and capability to determine the correct products for their application. Any
technical advice inferred from this Information or otherwise provided by KEMET with reference to the use of KEMET’s products is given gratis, and KEMET assumes
no obligation or liability for the advice given or results obtained.

Although KEMET designs and manufactures its products to the most stringent quality and safety standards, given the current state of the art, isolated component
failures may still occur. Accordingly, customer applications which require a high degree of reliability or safety should employ suitable designs or other safeguards
(such as installation of protective circuitry or redundancies) in order to ensure that the failure of an electrical component does not result in a risk of personal injury
or property damage.

Although all product–related warnings, cautions and notes must be observed, the customer should not assume that all safety measures are indicated or that other
measures may not be required.

KEMET is a registered trademark of KEMET Electronics Corporation.

© KEMET Electronics Corporation • One East Broward Boulevard C1104_KJN • 8/22/2023 19

Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com