Chapter 20 DLPs D300 to D399 D330 Install 120-Ohm E-1 Cables with Molex 96-Pin LFH Connectors

DLP-D330 Install 120-Ohm E-1 Cables with Molex 96-Pin LFH Connectors
Purpose This task installs the 120-ohm E-1 cables on FMEC E1-120NP, FMEC E1-120PROA, and FMEC E1-120PROB cards. Also use this task to install the 120-ohm E-1 cables on the E1-75/120 conversion panel. Twisted-pair cables with Molex 96-pin LFH connectors As needed Onsite None

Tools/Equipment Required/As Needed Onsite/Remote Security Level

Prerequisite Procedures NTP-D220 Install the Power and Signal FMECs, page 1-7

Using the cables with Molex 96-pin LFH connectors available from Cisco, connect the male connector to the female connector on the FMEC card that you want to connect to. Use Table 20-4 to make the connection from the E-1 96-pin connector for Ports 1 to 21 to the external balanced 120-ohm E-1 interfaces.

Table 20-4

Pinout for E-1 Interfaces on Ports 1 to 21

Pin Signal No. Name 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18

Wire Color

Pin Signal No. Name 25 26 RX 11 N RX 11 P RX 10 N RX 10 P RX 9 N RX 9 P RX 8 N RX 8 P RX 7 N RX 7 P RX 6 N RX 6 P RX 5 N RX 5 P RX 4 N RX 4 P RX 3 N RX 3 P

Wire Color white-blue blue-white

Pin Signal No. Name 49 50

Wire Color

Pin Signal No. Name 73 74 75 76 77 78 79 80 81 82 RX 21 P RX 20 P RX 19 P RX 18 P RX 17 P

Wire Color orange-black green-black brown-black slate-black blue-yellow

TX 11 N white-blue TX 11 P blue-white

TX 21 N black-orange TX 21 P orange-black TX 20 N black-green TX 20 P green-black TX 19 N black-brown TX 19 P brown-black TX 18 N black-slate TX 18 P slate-black TX 17 N yellow-blue TX 17 P blue-yellow

RX 21 N black-orange RX 20 N black-green RX 19 N black-brown RX 18 N black-slate RX 17 N yellow-blue RX 16 N yellow-orang e RX 16 P orange-yello w green-yellow

TX 10 N white-orange 27 TX 10 P orange-white 28 TX 9 N TX 9 P TX 8 N TX 8 P TX 7 N TX 7 P TX 6 N TX 6 P TX 5 N TX 5 P TX 4 N TX 4 P TX 3 N TX 3 P white-green green-white white-brown brown-white white-slate slate-white red-blue blue-red red-orange orange-red red-green green-red red-brown brown-red 29 30 31 32 33 34 35 36 37 38 39 40 41 42

white-orange 51 orange-white 52 white-green green-white white-brown brown-white white-slate slate-white red-blue blue-red red-orange orange-red red-green green-red red-brown brown-red 53 54 55 56 57 58 59 60 61 62 63 64 65 66

TX 16 N yellow-orange 83 TX 16 P orange-yellow 84 TX 15 N yellow-green TX 15 P green-yellow 85 86

RX 15 N yellow-green RX 15 P RX 14 N yellow-brow n RX 14 P brown-yello w slate-yellow

TX 14 N yellow-brown 87 TX 14 P brown-yellow 88 TX 13 N yellow-slate TX 13 P slate-yellow 89 90

RX 13 N yellow-slate RX 13 P

Cisco ONS 15454 SDH Procedure Guide, R9.0 78-18384-01

20-21

Chapter 20 DLPs D300 to D399 D330 Install 120-Ohm E-1 Cables with Molex 96-Pin LFH Connectors

Table 20-4

Pinout for E-1 Interfaces on Ports 1 to 21 (continued)

Pin Signal No. Name 19 20 21 22 23 24 TX 2 N TX 2 P TX 1 N TX 1 P

Wire Color red-slate slate-red black-blue blue-black

Pin Signal No. Name 43 44 45 46 47 48 RX 2 N RX 2 P RX 1 N RX 1 P

Wire Color red-slate slate-red black-blue blue-black

Pin Signal No. Name 67 68 69 70 71 72

Wire Color

Pin Signal No. Name 91 92 93 94 95 96 RX 12 P

Wire Color blue-violet

TX 12 N violet-blue TX 12 P blue-violet

RX 12 N violet-blue

Use Table 20-5 to make the connection from the E-1 96-pin connector for Ports 22 to 42 to the external balanced 120-ohm E-1 interfaces.
Table 20-5 Pinout for E-1 Interfaces on Ports 22 to 42

Pin Signal No. Name 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 TX 32 P

Wire Color blue-white

Pin No. 25 26

Signal Name

Wire Color

Pin No. 49 50

Signal Name

Wire Color

Pin No.

Signal Name RX 42 P

Wire Color orange-black

TX 32 N white-blue

RX 32 N white-blue RX 32 P blue-white

TX 42 N black-orange 73 TX 42 P orange-black 74 TX 41 N black-green TX 41 P green-black TX 40 N black-brown TX 40 P brown-black TX 39 N black-slate TX 39 P slate-black TX 38 N yellow-blue TX 38 P blue-yellow 75 76 77 78 79 80 81 82

RX 42 N black-orange RX 41 N black-green RX 41 P green-black

TX 31 N white-orang 27 e TX 31 P orange-whit 28 e 29 30 green-white

RX 31 N white-orang 51 e RX 31 P orange-whit 52 e RX 30 N white-green RX 29 N white-brow n RX 29 P brown-whit e RX 28 N white-slate RX 28 P slate-white RX 27 N red-blue RX 27 P blue-red RX 26 N red-orange RX 26 P orange-red RX 25 N red-green RX 25 P green-red RX 24 N red-brown 53 55 56 57 58 59 60 61 62 63 64 65 RX 30 P green-white 54

TX 30 N white-green TX 30 P

RX 40 N black-brown RX 40 P brown-black RX 39 N black-slate RX 39 P slate-black

TX 29 N white-brown 31 TX 29 P brown-white 32 33 34 35 36 37 38 39 40 41

TX 28 N white-slate TX 28 P slate-white TX 27 N red-blue TX 27 P blue-red

RX 38 N yellow-blue RX 38 P blue-yellow RX 37 N yellow-orang e RX 37 P orange-yello w green-yellow

TX 37 N yellow-orang 83 e TX 37 P orange-yello w 84

TX 26 N red-orange TX 26 P orange-red TX 25 N red-green TX 25 P green-red

TX 36 N yellow-green 85 TX 36 P green-yellow 86 TX 35 N yellow-brow n TX 35 P brown-yello w TX 34 N yellow-slate 87 88 89

RX 36 N yellow-green RX 36 P RX 35 N yellow-brow n RX 35 P brown-yello w

TX 24 N red-brown

RX 34 N yellow-slate

Cisco ONS 15454 SDH Procedure Guide, R9.0

20-22

78-18384-01

Chapter 20 DLPs D300 to D399 D332 Install the TCC2/TCC2P Cards

Table 20-5

Pinout for E-1 Interfaces on Ports 22 to 42 (continued)

Pin Signal No. Name 18 19 20 21 22 23 24 TX 24 P TX 23 P TX 22 P

Wire Color brown-red slate-red blue-black

Pin No. 42 43 44 45 46 47 48

Signal Name

Wire Color

Pin No. 66 67 68 69 70 71 72

Signal Name

Wire Color

Pin No. 90 91 92 93 94 95 96

Signal Name RX 34 P RX 33 P

Wire Color slate-yellow blue-violet

RX 24 P brown-red RX 23 N red-slate RX 23 P slate-red RX 22 N black-blue RX 22 P blue-black

TX 34 P slate-yellow TX 33 N violet-blue TX 33 P blue-violet

TX 23 N red-slate TX 22 N black-blue

RX 33 N violet-blue

Tighten the screws of the cable connector to the FMEC connector. Label all cables at each end of the connection to avoid confusion with cables that are similar in appearance. Return to your originating procedure (NTP).

DLP-D332 Install the TCC2/TCC2P Cards

Tools/Equipment Required/As Needed Onsite/Remote Security Level

Prerequisite Procedures None

When installing cards, allow each card to boot completely before installing the next card.

Step 1 Step 2 Step 3

Open the latches/ejectors of the TCC2/TCC2P card that you will install. Use the latches/ejectors to firmly slide the card along the guide rails until the card plugs into the receptacle at the back of the slot (Slot 7 or 11). Verify that the card is inserted correctly and close the latches/ejectors on the card.

Note

It is possible to close the latches/ejectors when the card is not completely plugged into the backplane. Ensure that you cannot insert the card any further.

If you insert a card into a slot provisioned for a different card, all LEDs turn off.

Cisco ONS 15454 SDH Procedure Guide, R9.0 78-18384-01

20-23