Scribd
Upload
25 views1 page

SX20C

Uploaded by

youcef
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
25 views1 page

SX20C

Uploaded by

youcef
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

SX20C SX20C

General Specifications General Specifications


The SX20C Cross-Needle power meter combines two meters which indicate forward The SX20C Cross-Needle power meter combines two meters which indicate forward
and reflected power respectively. It provides the direct read out of the SWR value and reflected power respectively. It provides the direct read out of the SWR value
from the crossing of two pointers. from the crossing of two pointers.
Specifications Specifications
Frequency Range 3.5 - 150 MHz Frequency Range 3.5 - 150 MHz
Input Impedance 50 ohms Input Impedance 50 ohms
Power Range 30W or 300W switchable Power Range 30W or 300W switchable
Power Readings Direct read out Power Readings Direct read out
Power Accuracy 10% at full scale Power Accuracy 10% at full scale
Min. Power Requirement FOR MEASURING SWR 3W Min. Power Requirement FOR MEASURING SWR 3W
Input/Output Connector UHF Input/Output Connector UHF
Dimensions 85W x 87H x 95D m/m Dimensions 85W x 87H x 95D m/m
Setting Up Setting Up
Connect the TX output of the transceiver to the “TX” connector and the antenna to Connect the TX output of the transceiver to the “TX” connector and the antenna to
the “ANT” connector, both located on the rear panel of the unit. Use 50 ohms coaxial the “ANT” connector, both located on the rear panel of the unit. Use 50 ohms coaxial
cable for the connections. cable for the connections.
Precautions Precautions
1) No mechanical shock to be given to the unit as it employs precision meters. 1) No mechanical shock to be given to the unit as it employs precision meters.
2) Do not transmit with an antenna out of tune, or open condition, as it may burn out 2) Do not transmit with an antenna out of tune, or open condition, as it may burn out
the meter by high voltage. the meter by high voltage.
Operation Operation
Be sure the power output range of the Be sure the power output range of the
transceiver and set the LO / HIGH range transceiver and set the LO / HIGH range
accordingly. LO / HI switch is depressed for accordingly. LO / HI switch is depressed for
high (30W to 300W) range, and out for high (30W to 300W) range, and out for
lowest (3W to 30W) range. lowest (3W to 30W) range.
Keying the transceiver, measure the required Keying the transceiver, measure the required
parameters as follows. parameters as follows.
• Forward power ~ follow the forward scale • Forward power ~ follow the forward scale
and read. and read.
• Reflected power ~ follow the reflected • Reflected power ~ follow the reflected
scale and read. scale and read.
• Standing wave radio (SWR) ~ follow the • Standing wave radio (SWR) ~ follow the
SWR scale from the point of pointers SWR scale from the point of pointers
crossing and read. crossing and read.

DIAMOND ANTENNA Products are distributed by RF PARTS COMPANY DIAMOND ANTENNA Products are distributed by RF PARTS COMPANY
435 S. Pacific Street • San Marcos, CA 92078 • (760) 744-0900 • www.diamondantenna.net 435 S. Pacific Street • San Marcos, CA 92078 • (760) 744-0900 • www.diamondantenna.net

You might also like