LTE Radio Access, Rel.

FDD-
LTE15A, Operating
Documentation, Issue 02

LTE OMS LDAP Parameters

DN0990203
Issue 07B
Approval Date 2016-04-06
The information in this document applies solely to the hardware/software product (“Product”) specified
herein, and only as specified herein.

This document is intended for use by Nokia Solutions and Networks' customers (“You”) only, and it may not
be used except for the purposes defined in the agreement between You and Nokia Solutions and Networks
(“Agreement”) under which this document is distributed. No part of this document may be used, copied,
reproduced, modified or transmitted in any form or means without the prior written permission of Nokia
Solutions and Networks. If you have not entered into an Agreement applicable to the Product, or if that
Agreement has expired or has been terminated, You may not use this document in any manner and You
are obliged to return it to Nokia Solutions and Networks and destroy or delete any copies thereof.

The document has been prepared to be used by professional and properly trained personnel, and You
assume full responsibility when using it. Nokia Solutions and Networks welcome Your comments as part of
the process of continuous development and improvement of the documentation.

This document and its contents are provided as a convenience to You. Any information or statements
concerning the suitability, capacity, fitness for purpose or performance of the Product are given solely on
an “as is” and “as available” basis in this document, and Nokia Solutions and Networks reserves the right
to change any such information and statements without notice. Nokia Solutions Networks has made all
reasonable efforts to ensure that the content of this document is adequate and free of material errors and
omissions, and Nokia Solutions and Networks will correct errors that You identify in this document. But,
Nokia Solutions and Networks' total liability for any errors in the document is strictly limited to the correction
of such error(s). Nokia Solutions and Networks does not warrant that the use of the software in the Product
will be uninterrupted or error-free.

NO WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO
ANY WARRANTY OF AVAILABILITY, ACCURACY, RELIABILITY, TITLE, NON-INFRINGEMENT,
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, IS MADE IN RELATION TO THE
CONTENT OF THIS DOCUMENT. IN NO EVENT WILL NOKIA SOLUTIONS AND NETWORKS BE
LIABLE FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO SPECIAL, DIRECT, INDIRECT,
INCIDENTAL OR CONSEQUENTIAL OR ANY LOSSES, SUCH AS BUT NOT LIMITED TO LOSS OF
PROFIT, REVENUE, BUSINESS INTERRUPTION, BUSINESS OPPORTUNITY OR DATA THAT MAY
ARISE FROM THE USE OF THIS DOCUMENT OR THE INFORMATION IN IT, EVEN IN THE CASE OF
ERRORS IN OR OMISSIONS FROM THIS DOCUMENT OR ITS CONTENT.

This document is Nokia Solutions and Networks’ proprietary and confidential information, which may not be
distributed or disclosed to any third parties without the prior written consent of Nokia Solutions and
Networks.

Nokia is a registered trademark of Nokia Corporation. Other product names mentioned in this document
may be trademarks of their respective owners, and they are mentioned for identification purposes only.

Copyright © 2014 Nokia Solutions and Networks. All rights reserved.

Important Notice on Product Safety

This product may present safety risks due to laser, electricity, heat, and other sources of
danger.

Only trained and qualified personnel may install, operate, maintain or otherwise handle this
distributed or disclosed to any third parties without the prior written consent of Nokia Solutions and
Networks.

Nokia is a registered trademark of Nokia Corporation. Other product names mentioned in this document
may be trademarks of their respective owners, and they are mentioned for identification purposes only.

Copyright © 2014 Nokia Solutions and Networks. All rights reserved.

Important Notice on Product Safety

This product may present safety risks due to laser, electricity, heat, and other sources of
danger.

Only trained and qualified personnel may install, operate, maintain or otherwise handle this
product and only after having carefully read the safety information applicable to this product.

The safety information is provided in the Safety Information section in the “Legal, Safety and
Environmental Information” part of this document or documentation set.

Nokia Solutions and Networks is continually striving to reduce the adverse environmental effects of its
products and services. We would like to encourage you as our customers and users to join us in working
towards a cleaner, safer environment. Please recycle product packaging and follow the recommendations
for power use and proper disposal of our products and their components.

If you should have questions regarding our Environmental Policy or any of the environmental services we
offer, please contact us at Nokia Solutions and Networks for any additional information.
 Product”) specified

ou”) only, and it may not

Solutions and Networks
may be used, copied,
permission of Nokia
he Product, or if that
any manner and You
copies thereof.

personnel, and You

our comments as part of

tion or statements
ct are given solely on
orks reserves the right
tworks has made all
of material errors and
this document. But,
y limited to the correction
software in the Product

UT NOT LIMITED TO
RINGEMENT,
RELATION TO THE
NETWORKS BE
ECT, INDIRECT,
TED TO LOSS OF
R DATA THAT MAY
EN IN THE CASE OF

mation, which may not be

a Solutions and

ned in this document

ation purposes only.

sources of

e handle this
 a Solutions and

ned in this document

ation purposes only.

sources of

e handle this
o this product.

al, Safety and

mental effects of its

s to join us in working
w the recommendations

ronmental services we
tion.
1. Introduction
The purpose of this document is to assist users in finding parameters, their meanings, specifications, and default values. Th
managed objects and parameters are listed in alphabetical order.

2. How to read this excel report

The excel report provides a full information on the parameter dictionary. It shows the full set of parameter attributes includin
the change information.

2.1 Parameter List

This section shows the full parameter information including the following:
- abbreviated names
- parent structure
- default values
- range and step
- field descriptions
- change information

2.2 Field descriptions

Field descriptions are provided in the second row of Parameter List section. Use fold (-) and unfold (+) buttons on the left
panel to respectively hide and show the field descriptions.

2.3 Change information

Change information is a part of Parameter List section and is available in the following ways:

1. Definition on whether the parameter is new, removed, changed, or has been moved to another location in the structure (f
example, to another managed object class). That definition is provided in the following columns:

- Changes between issues ... which shows the changes since the previous issue of the document.
- Changes between releases ... which shows the changes since the latest issue of the document in the previous product
release.

If the cell is empty, the parameter is not changed, nor new, nor removed, nor moved.
Note that removed parameters are listed in the very bottom and they are marked with red font.

Filters are enabled for convenient browsing of the change categories.

2. Detailed change information showing the current and previous values of parameter attributes. That information is provide
in the following columns:

- <parameter attribute> in issue ... which shows the value in the previous issue of the document.
- <parameter attribute> in release ... which shows value in the latest issue of the document in the previous product release.

The columns are grouped into attribute-specific sections for structured and convenient view. Use unfold (+) and fold (-) butt
in the top bar to browse the attribute-specific change details. Use unfold all (2) and fold all (1) buttons on the left hand side
the top bar to respectively show and hide the change details for the whole report.

Note that for all parameters except new and removed ones, the field values for previous issue and previous release are
always provided to show total history information. Additionally, the changed attributes of parameters are highlighted with gr
color. Highlights are enabled to specify whether there is a change between issues or releases.
 cations, and default values. The

of parameter attributes including

unfold (+) buttons on the left

other location in the structure (for

ns:

ment.
ment in the previous product

t.

es. That information is provided

ent.
the previous product release.

Use unfold (+) and fold (-) buttons

) buttons on the left hand side of

e and previous release are

ameters are highlighted with grey
s.
Note:
See the How to Read This Report tab
for instructions on the usage of Parameter List

Field description

Changes between issues Changes between releases Abbreviated Name

07A and 07B LTE OMS 15A and LTE
OMS 15A

ActiveN3CF

BTSFTPAlarmSetDelay

BackupEnabled

CANECloseCertUpdateTimerAdv

CANECloserCertUpdateTimerAdv

CRLPeriodicDownloadTimer
CmpKeyUpdtProtAgainstInstaServe
rFault

DB_Alarm

DB_CMPlan

DB_CosNaming

DB_Topology

DataStoringDelay

DeleteFilesAfterRead

DeleteTemporaryFiles

DeleteTemporaryFilesTimePeriod

DwAlarmForUploadCompleted

DwBTSLogObsolescenceTimeMins

DwBTSUploadEnabled
 DwFlags

DwLogSizeInKB

DwMaxConcurrentBTSUploads

DwMaxPercentageDiskUsage

DwNELogDaysSpan

FSNWI3N3CF

Fsnwi3N3CFId

Changed Changed InitialRegistrationPassword

InitialRegistrationUsername

LDAPConnectionType

PrimaryLDAPConfigurationRootDN

Changed Changed PrimaryLDAPPort

 PrimaryLDAPServer

PrimaryPeopleRootDN

RegistrationServiceIOR

SecondaryLDAPConfigurationRoot
DN

Changed Changed SecondaryLDAPPort

SecondaryLDAPServer

SecondaryPeopleRootDN

TakeIntoUseNext

FsHeartbeatInterval

MaxQuantityPassiveSWSets

MinimumFreeSpaceNeededForBac
kup

Changed Changed NEAccountPassword

NEAccountUsername

NEActivateRetryCount

NEBaseTimeout

NEDownloadRetryCount

NERetryCount

NERetryCountForEmergency

NERollbackRetryCount

NEUploadRetryCount

NetActNotifyEnabled

NorthboundIPAddress

NotifReceiptCheckStart

NotifReceiptCheckStep
OmsNicBandwidthAbsoluteLimit

OmsNicBandwidthLimitStatus

OmsNicBandwidthRelativeLimit

OverloadControlWindowFMTimeout

OverloadControlWindowLogViewer
Timeout

OverloadControlWindowSWViewer
Timeout

OverloadControlWindowTopoBrows
erTimeout

PMFileBufferAlarmCancelThreshold

PMFileBufferAlarmEnabled

PMFileBufferAlarmSetDelay

PMFileBufferAlarmSetThreshold

PMOverloadAlarmCancelThreshold
PMOverloadAlarmEnabled

PMOverloadAlarmSetThreshold

PMOverloadAlarmWindow

RUIMAutomaticActivation

SouthboundIPAddress

TLSModeFT

TLSModeOM

AutoConnHWID

AutoConnSiteID

BTSID

GPSTolerance

PREBTSID
 altitude

finalMediatorIPAddress

latitude

longitude

technologyInformation

version

Removed Removed DwControllerUploadEnabled

The Managed Object Class in Value in the previous issue of the Value in the previous product
which the parameter is document release
defined.

MO Class MO Class in issue 07A MO Class in release LTE 15A

OMS OMS OMS

OMS OMS OMS

OMS OMS OMS

OMS OMS OMS

OMS OMS OMS

OMS OMS OMS

OMS OMS OMS

OMS OMS OMS

OMS OMS OMS

OMS OMS OMS

OMS OMS OMS

OMS OMS OMS

OMS OMS OMS

OMS OMS OMS

OMS OMS OMS

OMS OMS OMS

OMS OMS OMS

OMS OMS OMS

OMS OMS OMS

OMS OMS OMS

OMS OMS OMS

OMS OMS OMS

OMS OMS OMS

OMS OMS OMS

OMS OMS OMS

OMS OMS OMS

OMS OMS OMS

OMS OMS OMS

OMS OMS OMS

OMS OMS OMS

OMS OMS OMS

OMS OMS OMS

OMS OMS OMS

OMS OMS OMS

OMS OMS OMS

OMS OMS OMS

OMS OMS OMS

OMS OMS OMS

OMS OMS OMS

OMS OMS OMS

OMS OMS OMS

OMS OMS OMS

OMS OMS OMS

OMS OMS OMS

OMS OMS OMS

OMS OMS OMS

OMS OMS OMS

OMS OMS OMS

OMS OMS OMS

OMS OMS OMS

OMS OMS OMS

OMS OMS OMS

OMS OMS OMS

OMS OMS OMS

OMS OMS OMS

OMS OMS OMS

OMS OMS OMS

OMS OMS OMS

OMS OMS OMS

OMS OMS OMS

OMS OMS OMS

OMS OMS OMS

OMS OMS OMS

OMS OMS OMS

OMS OMS OMS

OMS OMS OMS

OMS OMS OMS

OMS OMS OMS

OMS OMS OMS

OMS OMS OMS

OMS OMS OMS

OMS OMS OMS

OMS OMS OMS

PREBTS PREBTS PREBTS

PREBTS PREBTS PREBTS

PREBTS PREBTS PREBTS

PREBTS PREBTS PREBTS

PREBTS PREBTS PREBTS

PREBTS PREBTS PREBTS

PREBTS PREBTS PREBTS

PREBTS PREBTS PREBTS

PREBTS PREBTS PREBTS

PREBTS PREBTS PREBTS

PREBTS PREBTS PREBTS

OMS
For a parameter within a structure, this Value in the previous issue of the
field gives the abbreviated name of the document
structure. For standalone parameters,
this field is empty.

Parent Structure Parent Structure in issue 07A

FSNWI3N3CF FSNWI3N3CF

FSNWI3N3CF FSNWI3N3CF

FSNWI3N3CF FSNWI3N3CF

FSNWI3N3CF FSNWI3N3CF

FSNWI3N3CF FSNWI3N3CF

FSNWI3N3CF FSNWI3N3CF
FSNWI3N3CF FSNWI3N3CF

FSNWI3N3CF FSNWI3N3CF

FSNWI3N3CF FSNWI3N3CF

FSNWI3N3CF FSNWI3N3CF

FSNWI3N3CF FSNWI3N3CF

FSNWI3N3CF FSNWI3N3CF

FSNWI3N3CF FSNWI3N3CF

FSNWI3N3CF FSNWI3N3CF
Value in the previous product release For a structure, this field lists the
abbreviated names of all child
parameters. For standalone parameters,
this field is empty.

Parent Structure in release LTE 15A Child Parameters

 • Fsnwi3N3CFId
• InitialRegistrationPassword
• InitialRegistrationUsername
• LDAPConnectionType
• PrimaryLDAPConfigurationRootDN
FSNWI3N3CF

FSNWI3N3CF

FSNWI3N3CF

FSNWI3N3CF

FSNWI3N3CF

FSNWI3N3CF
FSNWI3N3CF

FSNWI3N3CF

FSNWI3N3CF

FSNWI3N3CF

FSNWI3N3CF

FSNWI3N3CF

FSNWI3N3CF

FSNWI3N3CF
The user interface name for the The parameter datatype. The functional group which the
parameter. parameter belongs to.

Full Name Data Type Parameter Group

Active N3CF String NWI3 and CUAA Management

BTS File transfer alarm set delay Number Performance Management

Backup enabled Enumeration Performance Management

CANE close certificate update timer Number OMS System

advance

CANE closer certificate update timer Number OMS System

advance

CRL periodic download timer Number OMS System

CMP Key Update protection against Enumeration OMS System
Insta server fault

DB_Alarm/fsdbBackup Enumeration Software Management

DB_CMPlan/fsdbBackup Enumeration Software Management

DB_CosNaming/fsdbBackup Enumeration Software Management

DB_Topology/fsdbBackup Enumeration Software Management

Data storing delay Number Performance Management

Delete files after read Enumeration Performance Management

Delete temporary files Enumeration Configuration Management

Delete temporary files time period Number Configuration Management

dw alarm for upload completed Enumeration OMS System

BTS Log Obsolescence Time Number OMS System

dw BTS upload enabled Enumeration OMS System

Process trace logging Enumeration OMS System

Trace log file size Number OMS System

Maximum number of concurrent Number OMS System

BTS uploads

Maximum Percentage Disk Usage Number OMS System

NE Log Days Span Number OMS System

FSNWI3N3CF Structure NWI3 and CUAA Management

fsnwi3N3CF Identifier Number NWI3 and CUAA Management

initial registration password String NWI3 and CUAA Management

initial registration username String NWI3 and CUAA Management

LDAP connection type Enumeration NWI3 and CUAA Management

Primary LDAP configuration root DN String NWI3 and CUAA Management

Primary LDAP port Number NWI3 and CUAA Management

Primary LDAP server String NWI3 and CUAA Management

Primary people root DN String NWI3 and CUAA Management

Registration service IOR String NWI3 and CUAA Management

Secondary LDAP configuration root String NWI3 and CUAA Management

DN

Secondary LDAP Port Number NWI3 and CUAA Management

Secondary LDAP server String NWI3 and CUAA Management

Secondary people root DN String NWI3 and CUAA Management

fsnwi3 take into use next Enumeration NWI3 and CUAA Management

fs Heartbeat Interval Number Configuration Management

Max quantity passive SW sets Number Software Management

Minimum free space needed for Number Software Management

backup

NE account password String NWI3 and CUAA Management

NE account username String NWI3 and CUAA Management

NE Activate Retry Count Number Configuration Management

NE Base Timeout Number Configuration Management

NE Download Retry Count Number Configuration Management

NE Retry Count Number Configuration Management

NE Retry Count for Emergency Number Configuration Management

NE Rollback Retry Count Number Configuration Management

NE Upload Retry Count Number Configuration Management

NetAct notify enabled Enumeration OMS System

OMS northbound IP address String OMS System

Notif receipt check start Number Performance Management

Notif receipt check step Number Performance Management

OMS NIC bandwidth absolute limit Number OMS System

OMS NIC bandwidth limit status Enumeration OMS System

OMS NIC bandwidth relative limit Number OMS System

Overload control window Fault Number OMS System

Management timeout

Overload control window Log Number OMS System

Viewer timeout

Overload control window SW Number OMS System

Version Viewer timeout

Overload control window Topology Number OMS System

Browser Timeout

PM file buffer alarm cancel Number Performance Management

threshold

PM file buffer alarm enabled Enumeration Performance Management

PM file buffer alarm set delay Number Performance Management

PM file buffer alarm set threshold Number Performance Management

PM overload alarm cancel threshold Number Performance Management

PM overload alarm enabled Enumeration Performance Management

PM overload alarm set threshold Number Performance Management

PM overload alarm window Number Performance Management

RUIM automatic activation Enumeration NWI3 and CUAA Management

OMS southbound IP Address String OMS System

TLS mode file transfer Enumeration OMS System

TLS mode OM Enumeration OMS System

Auto Connection Hardware ID String

Auto Connection site ID String

BTS Identifier Number

GPS Tolerance Number

PREBTS Identifier Number

GPS Antenna Altitude Number

Final Mediator IP Address String

GPS Antenna Latitude Number

GPS Antenna Longitude Number

Technology Information Enumeration

Version String

dw Controller upload enabled Enumeration OMS System

Describes in detail the purpose of the parameter and includes The value range for the
extra information on the parameter. parameter and the value by
which this parameter value
increases or decreases
within the range, including
the unit in which this
parameter is given or shown
in the user interface.

Description Range and step

This parameter defines the Distinguished Name (DN) of the 1...256 characters
currently active mediator configuration (N3CF) for NWI3
Registration and RUIM services, maintained by the
NWI3Adapter.
This parameter defines the minimum time between consecutive 0...1000 min, step 1 min
failed file transfer operations that trigger alarm.

default = 30
possible values = 0-1000 minutes
When this parameter is activated, the copies of measurement copying disabled (0),
files are stored into the /var/opt/OMSftproot/xmlfilesBU copying enabled (1)
directory.
Note that only the OMeS files produced by OMS are notified to
NetAct and stored in the backup directory.
This parameter defines how many days in advance to the 1...4999 day, step 1 day
CA/NE certificate expiry date, OMS triggers a CMP update
sequence or fetches CA certificates from the CR (if configured).

default = 90
This parameter defines how many days in advance to the 1...4999 day, step 1 day
CA/NE certificate expiry date, OMS sends the 71125
CERTIFICATE EXPIRING alarm and triggers a CMP update
sequence or fetches CA certificates from the CR (if configured).
This parameter defines in hours how often OMS downloads the 0...8760 hour, step 1 hour
CRL from CRL Distribution Point.

default = 24
possible values = 0-8760 hours
This parameter enables/disables control for CMP key update Disabled (0), Enabled (1)
operation to protect the system against excessively high value
of iterationCount parameter received in Key Update Response
(kup) message from Insta Certifier server (this incorrect value
results in high CPU usage for a certain period of time). The
This parameter activates the DB_Alarm database backup. S (0)

For the DB_Alarm backup the S value must be used to run

domain/subsystem specific scripts. The S value is set by
default. Changing or removing the S value for DB_Alarm can
This parameter activates the DB_CMPlan database backup. Y (0), N (1)
result in an unpredictable behavior of a network system and
default = N
possible values = Y, N
Y = enable database backup
This parameter activates the DB_CosNaming database Y (0), N (1)
backup.

default = N
possible values = Y, N
This parameter activates the DB_Topology database backup. S (0)

For the DB_Topology backup the S value must be used to run

domain/subsystem specific scripts. The S value is set by
default. Changing or removing the S value for DB_Topology
This parameter defines buffering delay for OMeS file writing. 1...30 min, step 1 min
can result in an unpredictable behavior of a network system
Note that changing the value of this parameter requires
MeaHandler restart with the following command: fshascli -rn
/MeaHandler. Modification of this parameter shall be done
carefully since measurement processing is a critical
This parameter stores the copies of measurement files received files are not deleted (0), files
from base stations into the are deleted permanently (1)
/var/opt/Nokia/OMS/OMSRNC/SS_RNCPM/btsfilesBU folder.

default = 1
This parameter indicates whether OMS should delete OMS does not delete
temporary plan files after the related operation has been temporary files (0), OMS
completed. Note that when the value is set to 0, OMS does not deletes temporary files (1)
clean downloaded or uploaded files after the related operation
has been completed. This can result in insufficient free disk
This parameter defines the period of time used for deletion of 1...6, step 1
temporary files from OMS disk.

This parameter enables or disables the 71106 alarm set disabled (0),
TROUBLESHOOTING DATA RECEIVED alarm setting for alarm set enabled (1)
troubleshooting data. By default, the OMS does not set an
alarm when new troubleshooting data is received.
Note that changing the value of this parameter requires
This parameter defines the time period after creation when log 1...120 min, step 1 min
NELogManager restart with the following command: fshascli -
may be deleted from OMS disk. No service restart required
r /NELogManager
after parameter change.

This parameter enables or disables the BTS Troubleshooting alarm set disabled (0),
file upload. Turning this parameter into the disabled does not alarm set enabled (1)
influence the already running uploads but it prevents new ones
from starting.
default = 1
This parameter defines whether process trace logging is active OFF (0), ERROR LEVEL
and what is the logging level. Modification of this parameter (1), WARNING LEVEL (2),
must be done carefully since incorrectly changing the value INFO LEVEL (3), DEBUG
may lead to turning off the logging functionality of OMS. LEVEL (4), TRACE LEVEL
(5)
This parameter defines the maximum size of trace log. Trace 0...65535, step 1
log file size in kilobytes
default = 15360 kB
maximum value: 65535 kB
This parameter defines the maximum number of concurrent 1...25, step 1
BTS uploads (number of processing threads). Increasing the
value has effect immediately. Decreasing may take some time
to have effect as running uploads are not stopped.
This parameter defines the maximum allowed disk usage 50...95 %, step 1 %
percentage threshold. No service restart required after
parameter change.

OMS deletes troubleshooting data files older than the period of 1...10, step 1
time defined by this parameter.

FSNWI3N3CF is a structure that stores NWI3 and CUAA Not defined

related parameters. This structure can have multiple instances
and ‘N3CF Identifier’ is ID parameter for each instance of
FSNWI3N3CF. Only one instance of ‘FSNWI3N3CF’ can be
active.
This is the fsnwi3N3CF Identifier. 1...24, step 1

This parameter defines a password corresponding to 6...512 characters

fsnwi3initialRegistrationUsername. Value shall be masked on
display in OMS Web UI.

This parameter defines a username which is used for NWI3 1...512 characters
registration.

This parameter defines LDAP connection type. It can only be TLS (0),
configured by NetAct. TLS_OR_PLAIN_TEXT (1)
default = TLS
possible values = TLS, TLS_OR_PLAIN_TEXT
This parameter defines the fragment in NetAct LDAP that 1...512 characters
contains further configuration attributes for primary NetAct
LDAP. It can only be configured by NetAct.

This parameter is not available by default.

This parameter defines the port number for the primary NetAct 0...65535, step 1
LDAP. It can only be configured by NetAct.

This parameter is not available by default.

This parameter defines the IP address of the primary NetAct 7...64 characters
LDAP. It can only be configured by NetAct.

This parameter is not available by default.

This parameter defines the root for searching user accounts in 1...512 characters
primary NetAct LDAP. It can only be configured by NetAct.

This parameter is not available by default.

IOR of the RegistrationService the mediator shall register to. 1...4096 characters

This parameter contains further configuration attributes for 1...512 characters

secondary NetAct LDAP. It can only be configured by NetAct.

This parameter is not available by default.

This parameter defines the port number for the secondary 0...65535, step 1
NetAct LDAP. It can only be configured by NetAct.

This parameter is not available by default.

This parameter defines the IP address of the secondary NetAct 7...64 characters
LDAP. It can only be configured by NetAct.

This parameter is not available by default.

This parameter defines the root for searching user accounts in 1...512 characters
secondary NetAct LDAP. It can only be configured by NetAct.

This parameter is not available by default.

This parameter is used by the NWI3Adapter and RUIM true (0), false (1)
Services to identify active configuration storing NWI3/CUAA
parameters (N3CF configuration). When the NWI3 Adapter or
RUIM is restarted, the necessary parameters are read from
active configuration. There should be only one N3CF with this
This parameter defines the time after which the alarm 70246 0...600 sec, step 1 sec
ALARM SYSTEM HEARTBEAT is raised or cancelled. The
alarm system is interchangeably raising and clearing this alarm
after the expiration of each heartbeat interval. If the refreshing
of the alarm does not occur, it signals that the alarm system is
This parameter defines the value of possible passive SW sets. 1...6, step 1
OMS limits the number of installed SW sets as passive
because of storage disk capacity limits.

This parameter specifies how much space (in GB) is reserved 1...86400 GB, step 1 GB
for a full backup. In a special case, for example, custom backup
of home directory, the size of a backup file can exceed 6 GB.
The operator has to estimate the assumed size of requested
item/data and modify the parameter’s value accordingly.
This parameter defines connection password to NetAct's 6...512 characters
remote LDAP. This parameter is read-only and can be
configured only using NetAct.
Value shall be masked when displayed on OMS Web UI.
This parameter is not available by default.
This parameter defines connection username to NetAct's 1...32 characters
remote LDAP. This parameter is read-only and can be
configured only using NetAct.

This parameter is not available by default.

This parameter a defines the maximum count of retries in plan 0...20, step 1
activation operations. NOTICE: It is advised that only advanced
users with a profound understanding of the retry mechanism
change the default value of this parameter. For more
information on retry mechanism, see LTE iOMS Unit
The value of base timeout in seconds. Used in resending 0...600 sec, step 1 sec
operation requests to NE.

This parameter a defines the maximum count of retries in plan 0...20, step 1
download operations. NOTICE: It is advised that only advanced
users with a profound understanding of the retry mechanism
change the default value of this parameter. For more
information on retry mechanism, see LTE iOMS Unit
This parameter defines the number of retry attempts for one 0...20, step 1
NE.

This parameter defines the number of retries for emergency 0...20, step 1
plan download and activation to NEs.

This parameter defines the value of the retry count for NE 0...5, step 1
rollback.

NOTICE: It is advised that only advanced users with a profound

understanding of the retry mechanism change the default value
This parameter defines the maximum count of retries in upload 0...20, step 1
of this parameter.
operations.

NOTICE: It is advised that only advanced users with a profound

understanding of the retry mechanism change the default value
This parameter disables/enables the FileReadyEvent_V1 upload disabled (0), upload
of this parameter.
notification to NetAct when a troubleshooting data file is enabled (1)
received. If the parameter is disabled, OMS does not send
FileReadyEvent_V1 to NetAct and the troubleshooting data file
remains in OMS.
OMS IP address for the upper level management systems (e.g. 7...64 characters
NetAct).The value is updated only by the
zmodifyNetworkSettings script.

This parameter defines the duration in seconds on when OMS 1...1800, step 1
shall start taking not of FileLoadPrepare message from eNB.
Modification of this parameter shall be done carefully as
measurement processing is critical functionality in OMS.
This parameter defines the duration in seconds OMS shall 1...1200, step 1
continuously check if FileLoadPrepare message was received
from eNB(s). Modification of this parameter shall be done
carefully as measurement processing is critical functionality in
OMS.
This parameter sets the maximum absolute OMS NIC 1...1000 mbps, step 1 mbps
bandwidth for the outgoing file transfer related traffic. It means
that the bandwidth used by all clients downloading files from
OMS simultaneously cannot exceed connection capacity
indicated by the current parameter value.
This parameter enables OMS NIC bandwidth limitation to avoid OMS NIC bandwidth
overload caused by file transfer traffic. limitation turned off (0),
OMS NIC bandwidth
default = 1 limitation turned on (1)
possible values = 0, 1
This parameter sets the maximum relative OMS network 1...99 %, step 1 %
interface bandwidth for the outgoing file transfer related traffic.
It defines the bandwidth limit as a percentage (%) of the actual
OMS NIC link speed. If there is only one IP address configured
on OMS NIC, change the parameter value to 90 %.
This parameter specifies the time-out (in seconds) of inactivity 60...86400 sec, step 1 sec
in Fault Management after which OMS attempts to terminate
the idle window session.

default = 3600 s
This parameter specifies the time-out (in seconds) of inactivity 60...86400 sec, step 1 sec
in Log Viewer after which OMS attempts to terminate the idle
window session.

default = 3600 s
This parameter specifies the time-out (in seconds) of inactivity 60...86400 sec, step 1 sec
in SW Version Viewer after which OMS attempts to terminate
the idle window session.

default = 3600 s
This parameter specifies the time-out (in seconds) of inactivity 60...86400 sec, step 1 sec
in Topology Browser after which OMS attempts to terminate the
idle window session.

default = 3600 s
This parameter cancels alarm threshold for buffer build-up 0...4294967295 files, step 1
alarms. If the alarm is active and the number of files decreases files
to this limit or below, the alarm is cancelled.
default = 10
possible values = 0-N files
This parameter disables/enables XML-file buffer build-up alarm. alarm disabled (0), alarm
default = 1 enabled (1)
possible values = 0, 1
0 = alarm disabled
1 = alarm enabled
This parameter sets delay for buffer buildup alarms, that is, the 0...86400 sec, step 1 sec
duration in seconds that the number of unacknowledged OMeS
files must be over the threshold.
default = 180
possible values = 0-N seconds
This parameter sets threshold for buffer build-up alarms. If the 0...4294967295 files, step 1
number of unacknowledged OMeS files reaches this limit, an files
alarm is triggered.

This parameter cancels alarm threshold for measurement data 1...100 %, step 1 %
processing overload alarm. If overload alarm is active and the
processing time in percentage of total time goes below this
threshold calculated over PMOverloadAlarmWindow duration,
the alarm is cancelled.
This parameter disables/enables measurement processing alarm disabled (0), alarm
overload alarm. enabled (1)

default = 1
possible values = 0, 1
This parameter sets alarm threshold for measurement data 1...100 %, step 1 %
processing overload alarms. If the processing time percentage
of total time exceeds the threshold calculated over
PMOverloadAlarmWindow duration, an alarm is set.
This parameter averages window for measurement processing 30...240 min, step 1 min
overload alarm. OMSMeaHandler
measures data processing time over this time window and if the
processing time exceeds
PMOverloadAlarmSetThreshold percentage of total time, an
When this parameter is activated, Centralized User RUIMAutomaticActivation
alarm is triggered. The same window is used for cancelling the
Authentication and authorization automated activation is disabled (0),
alarm based on PMOverloadAlarmCancelLimit
enabled. RUIMAutomaticActivation
enabled (1)
default = 0
OMS southbound server IP address. The value is updated only 7...64 characters
by the zmodifyNetworkSettings script.

This parameter defines security mode for file transfer. Forced (0), Probing (1), Off
(2)
possible values = Forced, Probing,Off

This parameter defines security mode for BTS O&M I/F. Forced (0), Probing (1), Off
(2)
possible values = Forced, Probing, Off

This identifies Hardware ID of NE, which the NE uses during 0...255 characters
autoconnection procedure to identify itself when the logical BTS
Id is not yet known to the NE.

Allowed characters are ASCII characters.

This is the unique identifier for the BTS site, which the NE uses 0...255 characters
during autoconnection procedure to identify itself,when the
logical BTS Id is not yet known to the NE.

Allowed characters are ASCII characters.

This defines unique identifier by which the BTS identifies itself 0...1048575, step 1
to the Network.

Note: Range in WCDMA 1..65534.

This parameter specifies allowed deviation (meters) of GPS -1...5000 m, step 1 m
location from expected value.

This parameter identifies PREBTS. 0...1048575, step 1

Altitude of GPS antenna of site -250...10000 m, step 1 m

IP Address for the Final Mediator 0...255 characters

Supported formats: IPv4 IP address and an IPv6IP address

Examples:
IPv4 IP-address 192.0.2.235
Latitude of GPS antenna of site -900000000...900000000,
step 1

Longitude of GPS antenna of site -1800000000...1800000000,

step 1

This parameter specifies technology of BTS. WCDMA (0), LTE (1),

LiteBTS (2), FlexiZoneMicro
(3)

This parameter specifies the version information that BTS 0...255 characters
should use as swVersion until it has been commissioned.

This parameter is used to switch on/off automatic data transfers upload disabled (0), upload
to OMS triggered by NE. enabled (1)

Note that changing the value of this parameter requires

NELogManager restart with the following command: fshascli –
r /NELogManager
The formula for calculating the system internal The parameter value Describes whether the
value (for example, ASN.1 value) which is the system will use if parameter can be
used between the system components, for there is no other value modified in the network
example, in provisioned or uploaded files. given. element and what impact
the modification has or
conditions to fulfil.

Formula for Getting Internal Value Default Value Modification

internal_value = gui_value Not modifiable

internal_value = gui_value 30 min On-line

gui ==> internal copying disabled (0) On-line

copying disabled ==> 0
copying enabled ==> 1

internal_value = gui_value 90 day On-line

internal_value = gui_value 30 day On-line

internal_value = gui_value 24 hour On-line

gui ==> internal Disabled (0) On-line
Disabled ==> 0
Enabled ==> 1

gui ==> internal S (0) On-line

S ==> 0

gui ==> internal N (1) On-line

Y ==> 0
N ==> 1

gui ==> internal N (1) On-line

Y ==> 0
N ==> 1

gui ==> internal S (0) On-line

S ==> 0

internal_value = gui_value 6 min On-line

gui ==> internal files are deleted On-line

files are not deleted ==> 0 permanently (1)
files are deleted permanently ==> 1

gui ==> internal OMS deletes temporary On-line

OMS does not delete temporary files ==> 0 files (1)
OMS deletes temporary files ==> 1

internal_value = gui_value 3 On-line

gui ==> internal alarm set enabled (1) On-line

alarm set disabled ==> 0
alarm set enabled ==> 1

internal_value = gui_value 120 min On-line

gui ==> internal alarm set enabled (1) On-line

alarm set disabled ==> 0
alarm set enabled ==> 1
gui ==> internal INFO LEVEL (3) On-line
OFF ==> 0
ERROR LEVEL ==> 1
WARNING LEVEL ==> 2
INFO LEVEL ==> 3
internal_value = gui_value 15360 On-line

internal_value = gui_value 25 On-line

internal_value = gui_value 90 % On-line

internal_value = gui_value 10 On-line

Not defined On-line

internal_value = gui_value 1 Not modifiable

internal_value = gui_value On-line

internal_value = gui_value On-line

gui ==> internal TLS (0) Not modifiable

TLS ==> 0
TLS_OR_PLAIN_TEXT ==> 1

internal_value = gui_value Not modifiable

internal_value = gui_value 0 Not modifiable

internal_value = gui_value 0.0.0.0 Not modifiable

internal_value = gui_value Not modifiable

internal_value = gui_value On-line

internal_value = gui_value Not modifiable

internal_value = gui_value 0 Not modifiable

internal_value = gui_value 0.0.0.0 Not modifiable

internal_value = gui_value Not modifiable

gui ==> internal false (1) On-line

true ==> 0
false ==> 1

internal_value = gui_value 300 sec On-line

internal_value = gui_value 6 On-line

internal_value = gui_value 6 GB On-line

internal_value = gui_value Not modifiable

internal_value = gui_value Not modifiable

internal_value = gui_value 6 On-line

internal_value = gui_value 300 sec On-line

internal_value = gui_value 6 On-line

internal_value = gui_value 5 On-line

internal_value = gui_value 2 On-line

internal_value = gui_value 5 On-line

internal_value = gui_value 6 On-line

gui ==> internal upload enabled (1) On-line

upload disabled ==> 0
upload enabled ==> 1

internal_value = gui_value 0.0.0.0 Not modifiable

internal_value = gui_value 90 On-line

internal_value = gui_value 30 On-line

internal_value = gui_value 200 mbps On-line

gui ==> internal OMS NIC bandwidth On-line

OMS NIC bandwidth limitation turned off ==> limitation turned on (1)
0
OMS NIC bandwidth limitation turned on ==>
1
internal_value = gui_value 70 % On-line

internal_value = gui_value 3600 sec On-line

internal_value = gui_value 3600 sec On-line

internal_value = gui_value 3600 sec On-line

internal_value = gui_value 3600 sec On-line

internal_value = gui_value 10 files On-line

gui ==> internal alarm enabled (1) On-line

alarm disabled ==> 0
alarm enabled ==> 1

internal_value = gui_value 180 sec On-line

internal_value = gui_value 100 files On-line

internal_value = gui_value 50 % On-line

gui ==> internal alarm enabled (1) On-line
alarm disabled ==> 0
alarm enabled ==> 1

internal_value = gui_value 60 % On-line

internal_value = gui_value 120 min On-line

gui ==> internal RUIMAutomaticActivatio On-line

RUIMAutomaticActivation disabled ==> 0 n disabled (0)
RUIMAutomaticActivation enabled ==> 1

internal_value = gui_value 0.0.0.0 Not modifiable

gui ==> internal Probing (1) On-line

Forced ==> 0
Probing ==> 1
Off ==> 2
gui ==> internal Probing (1) On-line
Forced ==> 0
Probing ==> 1
Off ==> 2
internal_value = gui_value On-line

internal_value = gui_value On-line

internal_value = gui_value On-line

internal_value = gui_value On-line

internal_value = gui_value Not modifiable

internal_value = gui_value On-line

internal_value = gui_value On-line

internal_value = gui_value On-line

internal_value = gui_value On-line

gui ==> internal LTE (1) On-line

WCDMA ==> 0
LTE ==> 1
LiteBTS ==> 2
FlexiZoneMicro ==> 3
internal_value = gui_value On-line

gui ==> internal upload enabled (1) On-line

upload disabled ==> 0
upload enabled ==> 1
Describes whether the parameter is Feature or license required to modify and take
mandatory or not. advantage of this parameter. If the system does not
have the necessary licenses, it ignores that
Note: Mandatory parameters with no parameter.
default value defined must be filled in.

Required on Creation Related Features

Mandatory • LTE666 LTE User Account Managament (optional)

• LTE1481 OMS LDAP web GUI (optional)

Mandatory • LTE657 LTE Performance Management (optional)

• LTE1481 OMS LDAP web GUI (optional)

Mandatory • LTE657 LTE Performance Management (optional)

• LTE1481 OMS LDAP web GUI (optional)

Mandatory • LTE524_RAN2267 Certificate Management for OMS

Products (optional)
• LTE1481 OMS LDAP web GUI (optional)

Mandatory • LTE524_RAN2267 Certificate Management for OMS

Products (optional)
• LTE1481 OMS LDAP web GUI (optional)

Mandatory • LTE1260 Certificate update and revocation support

(optional)
• LTE1481 OMS LDAP web GUI (optional)
Optional • LTE1260 Certificate update and revocation support
(optional)

Mandatory • LTE1481 OMS LDAP web GUI (optional)

• LTE1405 Remote SW-management and data
Backup Restore support for iOMS (optional)

Mandatory • LTE1481 OMS LDAP web GUI (optional)

• LTE1405 Remote SW-management and data
Backup Restore support for iOMS (optional)

Mandatory • LTE1481 OMS LDAP web GUI (optional)

• LTE1405 Remote SW-management and data
Backup Restore support for iOMS (optional)

Mandatory • LTE1481 OMS LDAP web GUI (optional)

• LTE1405 Remote SW-management and data
Backup Restore support for iOMS (optional)

Mandatory • LTE657 LTE Performance Management (optional)

• LTE1481 OMS LDAP web GUI (optional)

Mandatory • LTE657 LTE Performance Management (optional)

• LTE1481 OMS LDAP web GUI (optional)

Mandatory • LTE654 Configuration Management (optional)

• LTE1481 OMS LDAP web GUI (optional)

Mandatory • LTE654 Configuration Management (optional)

• LTE1481 OMS LDAP web GUI (optional)

Mandatory • LTE1099 Event-triggered symptom data collection

and provisioning (optional)
• LTE1481 OMS LDAP web GUI (optional)

Optional • LTE1099 Event-triggered symptom data collection

and provisioning (optional)
• LTE1481 OMS LDAP web GUI (optional)

Mandatory • LTE1099 Event-triggered symptom data collection

and provisioning (optional)
• LTE1481 OMS LDAP web GUI (optional)
Mandatory • LTE740 Integrated Operation Mediation Subsystem
(optional)
• LTE1481 OMS LDAP web GUI (optional)

Mandatory • LTE740 Integrated Operation Mediation Subsystem

(optional)
• LTE1481 OMS LDAP web GUI (optional)

Optional • LTE1099 Event-triggered symptom data collection

and provisioning (optional)
• LTE1481 OMS LDAP web GUI (optional)

Optional • LTE1099 Event-triggered symptom data collection

and provisioning (optional)
• LTE1481 OMS LDAP web GUI (optional)

Optional • LTE1099 Event-triggered symptom data collection

and provisioning (optional)
• LTE1481 OMS LDAP web GUI (optional)

Mandatory • LTE1481 OMS LDAP web GUI (optional)

Mandatory • LTE666 LTE User Account Managament (optional)

• LTE1481 OMS LDAP web GUI (optional)

Mandatory • LTE666 LTE User Account Managament (optional)

• LTE1481 OMS LDAP web GUI (optional)

Mandatory • LTE666 LTE User Account Managament (optional)

• LTE1481 OMS LDAP web GUI (optional)

Optional • LTE150 OMS Transport Layer Security Support

(optional)
• LTE1481 OMS LDAP web GUI (optional)

Optional • LTE666 LTE User Account Managament (optional)

• LTE1481 OMS LDAP web GUI (optional)

Optional • LTE666 LTE User Account Managament (optional)

• LTE1481 OMS LDAP web GUI (optional)
Optional • LTE666 LTE User Account Managament (optional)
• LTE1481 OMS LDAP web GUI (optional)

Optional • LTE666 LTE User Account Managament (optional)

• LTE1481 OMS LDAP web GUI (optional)

Mandatory • LTE666 LTE User Account Managament (optional)

• LTE1481 OMS LDAP web GUI (optional)

Optional • LTE666 LTE User Account Managament (optional)

• LTE1481 OMS LDAP web GUI (optional)

Optional • LTE666 LTE User Account Managament (optional)

• LTE1481 OMS LDAP web GUI (optional)

Optional • LTE666 LTE User Account Managament (optional)

• LTE1481 OMS LDAP web GUI (optional)

Optional • LTE666 LTE User Account Managament (optional)

• LTE1481 OMS LDAP web GUI (optional)

Mandatory • LTE666 LTE User Account Managament (optional)

• LTE1481 OMS LDAP web GUI (optional)

Mandatory • LTE654 Configuration Management (optional)

• LTE1481 OMS LDAP web GUI (optional)

Mandatory • LTE655 SW Management (optional)

• LTE1481 OMS LDAP web GUI (optional)

Mandatory • LTE1405 Remote SW-management and data

Backup Restore support for iOMS (optional)
• LTE1481 OMS LDAP web GUI (optional)

Optional • LTE666 LTE User Account Managament (optional)

• LTE1481 OMS LDAP web GUI (optional)
Optional • LTE666 LTE User Account Managament (optional)
• LTE1481 OMS LDAP web GUI (optional)

Mandatory • LTE654 Configuration Management (optional)

• LTE1481 OMS LDAP web GUI (optional)

Mandatory • RAN2698 Operability and Performance Monitoring

Agreed Corrections and Additons RU50 (optional)
• LTE1379 Operability and Performance Monitoring
Agreed Corrections and Additons RL50 (optional)
• LTE1068 S1 X2 Satellite Connection (optional)
Mandatory • LTE654 Configuration Management (optional)
• LTE1481 OMS LDAP web GUI (optional)

Mandatory • LTE654 Configuration Management (optional)

• LTE1481 OMS LDAP web GUI (optional)

Mandatory • LTE654 Configuration Management (optional)

• LTE1481 OMS LDAP web GUI (optional)

Mandatory • LTE654 Configuration Management (optional)

• LTE1481 OMS LDAP web GUI (optional)

Mandatory • LTE654 Configuration Management (optional)

• LTE1481 OMS LDAP web GUI (optional)

Mandatory • LTE740 Integrated Operation Mediation Subsystem

(optional)
• LTE1481 OMS LDAP web GUI (optional)

Mandatory • LTE740 Integrated Operation Mediation Subsystem

(optional)
• LTE1481 OMS LDAP web GUI (optional)

Mandatory • LTE657 LTE Performance Management (optional)

• LTE1481 OMS LDAP web GUI (optional)

Mandatory • LTE657 LTE Performance Management (optional)

• LTE1481 OMS LDAP web GUI (optional)
Mandatory • LTE740 Integrated Operation Mediation Subsystem
(optional)
• LTE1481 OMS LDAP web GUI (optional)

Mandatory • LTE740 Integrated Operation Mediation Subsystem

(optional)
• LTE1481 OMS LDAP web GUI (optional)

Mandatory • LTE740 Integrated Operation Mediation Subsystem

(optional)
• LTE1481 OMS LDAP web GUI (optional)

Mandatory • RAN1903 OMS Overload Control (optional)

• LTE1481 OMS LDAP web GUI (optional)

Mandatory • RAN1903 OMS Overload Control (optional)

• LTE1481 OMS LDAP web GUI (optional)

Mandatory • RAN1903 OMS Overload Control (optional)

• LTE1481 OMS LDAP web GUI (optional)

Mandatory • RAN1903 OMS Overload Control (optional)

• LTE1481 OMS LDAP web GUI (optional)

Mandatory • LTE657 LTE Performance Management (optional)

• LTE1481 OMS LDAP web GUI (optional)

Mandatory • LTE657 LTE Performance Management (optional)

• LTE1481 OMS LDAP web GUI (optional)

Mandatory • LTE657 LTE Performance Management (optional)

• LTE1481 OMS LDAP web GUI (optional)

Mandatory • LTE657 LTE Performance Management (optional)

• LTE1481 OMS LDAP web GUI (optional)

Mandatory • LTE657 LTE Performance Management (optional)

• LTE1481 OMS LDAP web GUI (optional)
Mandatory • LTE657 LTE Performance Management (optional)
• LTE1481 OMS LDAP web GUI (optional)

Mandatory • LTE657 LTE Performance Management (optional)

• LTE1481 OMS LDAP web GUI (optional)

Mandatory • LTE657 LTE Performance Management (optional)

• LTE1481 OMS LDAP web GUI (optional)

Mandatory • LTE666 LTE User Account Managament (optional)

• LTE1481 OMS LDAP web GUI (optional)

Mandatory • LTE740 Integrated Operation Mediation Subsystem

(optional)
• LTE1481 OMS LDAP web GUI (optional)

Mandatory • LTE150 OMS Transport Layer Security Support

(optional)
• LTE1481 OMS LDAP web GUI (optional)

Mandatory • LTE150 OMS Transport Layer Security Support

(optional)
• LTE1481 OMS LDAP web GUI (optional)

Optional • LTE1144 Operability and Performance Monitoring

AgreedCorrections and additions (optional)

Optional • LTE1144 Operability and Performance Monitoring

AgreedCorrections and additions (optional)

Mandatory • LTE1144 Operability and Performance Monitoring

AgreedCorrections and additions (optional)

Optional • LTE1144 Operability and Performance Monitoring

AgreedCorrections and additions (optional)

Mandatory • LTE1144 Operability and Performance Monitoring

AgreedCorrections and additions (optional)
Optional • LTE1144 Operability and Performance Monitoring
AgreedCorrections and additions (optional)

Optional • LTE1144 Operability and Performance Monitoring

AgreedCorrections and additions (optional)

Optional • LTE1144 Operability and Performance Monitoring

AgreedCorrections and additions (optional)

Optional • LTE1144 Operability and Performance Monitoring

AgreedCorrections and additions (optional)

Mandatory • SON LTE BTS Auto Connectivity (optional)

Mandatory • LTE1144 Operability and Performance Monitoring

AgreedCorrections and additions (optional)

Mandatory • LTE1099 Event-triggered symptom data collection

and provisioning (optional)
• LTE1481 OMS LDAP web GUI (optional)
The management interfaces over which this parameter
is transferred.

Interfaces

• OMS -> EM

• OMS <-> EM

• OMS <-> EM

• OMS <-> EM

• OMS <-> EM

• OMS <-> EM
• OMS <-> EM

• OMS <-> EM

• OMS <-> EM

• OMS <-> EM

• OMS <-> EM

• OMS <-> EM

• OMS <-> EM

• OMS <-> EM

• OMS <-> EM

• OMS <-> EM

• OMS <-> EM

• OMS <-> EM
• OMS <-> EM

• OMS <-> EM

• OMS <-> EM

• OMS <-> EM

• OMS <-> EM

• OMS <-> EM

• OMS -> EM

• OMS <-> EM

• OMS <-> EM

• OMS -> EM

• OMS -> EM

• OMS -> EM
• OMS -> EM

• OMS -> EM

• OMS <-> EM

• OMS -> EM

• OMS -> EM

• OMS -> EM

• OMS -> EM

• OMS <-> EM

• OMS <-> EM

• OMS <-> EM

• OMS <-> EM

• OMS -> EM
• OMS -> EM

• OMS <-> EM

• OMS <-> EM

• OMS <-> EM

• OMS <-> EM

• OMS <-> EM

• OMS <-> EM

• OMS <-> EM

• OMS <-> EM

• OMS -> EM

• OMS <-> EM

• OMS <-> EM
• OMS <-> EM

• OMS <-> EM

• OMS <-> EM

• OMS <-> EM

• OMS <-> EM

• OMS <-> EM

• OMS <-> EM

• OMS <-> EM

• OMS <-> EM

• OMS <-> EM

• OMS <-> EM

• OMS <-> EM
• OMS <-> EM

• OMS <-> EM

• OMS <-> EM

• OMS <-> EM

• OMS -> EM

• OMS <-> EM

• OMS <-> EM

• NE <-> OMS
• OMS <-> RAC
• RAC <-> RACApp

• NE <-> OMS
• OMS <-> RAC
• RAC <-> RACApp

• NE <-> OMS
• OMS <-> RAC
• RAC <-> RACApp

• NE <-> OMS
• OMS <-> RAC
• RAC <-> RACApp

• NE <-> OMS
• OMS <-> RAC
• RAC <-> RACApp
• NE <-> OMS
• OMS <-> RAC
• RAC <-> RACApp

• NE <-> OMS
• OMS <-> RAC
• RAC <-> RACApp

• NE <-> OMS
• OMS <-> RAC
• RAC <-> RACApp

• NE <-> OMS
• OMS <-> RAC
• RAC <-> RACApp

• NE <-> OMS
• OMS <-> RAC
• RAC <-> RACApp

• NE <-> OMS
• OMS <-> RAC
• RAC <-> RACApp

• OMS <-> EM
References (if any) to 3GPP specifications.

References
Actions required to take the parameter value changes
into use in OMS.

OMS - Additional Action Required

Restart NWI3Adapter service. fshascli –rn

/NWI3Adapter

Restart PMGeneric service. fshascli –rn /PMGeneric

Restart NWI3Certificate service. fshascli –rn

/NWI3Certificate

Restart NWI3Certificate service. fshascli –rn

/NWI3Certificate

Restart NWI3Certificate service. fshascli –rn

/NWI3Certificate
Restart NWI3Certificate service. fshascli –rn
/NWI3Certificate

Restart MeaHandler service. fshascli –rn /MeaHandler

Restart NWI3CM service. fshascli –rn /NWI3CM

Restart NWI3CM service. fshascli –rn /NWI3CM

Restart NWI3Adapter service. fshascli –rn
/NWI3Adapter

Restart NWI3Adapter service. fshascli –rn

/NWI3Adapter

Restart NWI3Adapter service. fshascli –rn

/NWI3Adapter

Restart the CUAA related recovery groups with the

following commands: fshascli -r /PAP fshascli -r
/RuimReplicator

Restart the CUAA related recovery groups with the

following commands: fshascli -r /PAP fshascli -r
/RuimReplicator

Restart the CUAA related recovery groups with the

following commands: fshascli -r /PAP fshascli -r
/RuimReplicator
Restart the CUAA related recovery groups with the
following commands: fshascli -r /PAP fshascli -r
/RuimReplicator

Restart the CUAA related recovery groups with the

following commands: fshascli -r /PAP fshascli -r
/RuimReplicator

Restart NWI3Adapter service. fshascli –rn

/NWI3Adapter

Restart the CUAA related recovery groups with the

following commands: fshascli -r /PAP fshascli -r
/RuimReplicator

Restart the CUAA related recovery groups with the

following commands: fshascli -r /PAP fshascli -r
/RuimReplicator

Restart the CUAA related recovery groups with the

following commands: fshascli -r /PAP fshascli -r
/RuimReplicator

Restart the CUAA related recovery groups with the

following commands: fshascli -r /PAP fshascli -r
/RuimReplicator

Restart NWI3Adapter service. fshascli –rn

/NWI3Adapter Restart the CUAA related recovery
groups with the following commands: fshascli -r /PAP
fshascli -r /RuimReplicator
Restart AlarmSystem service. fshascli –rn /AlarmSystem

Restart NWI3Adapter service. fshascli –rn

/NWI3Adapter
Restart NWI3Adapter service. fshascli –rn
/NWI3Adapter

Restart NWI3CM service. fshascli –rn /NWI3CM

Restart NWI3CM service. fshascli –rn /NWI3CM

Restart NWI3CM service. fshascli –rn /NWI3CM

Restart NWI3CM service. fshascli –rn /NWI3CM

Restart NWI3CM service. fshascli –rn /NWI3CM

Restart NWI3CM service. fshascli –rn /NWI3CM

Please do system restart.

Restart MeaHandler service. fshascli –rn /MeaHandler

Restart MeaHandler service. fshascli –rn /MeaHandler

Restart OMSAppControl service. fshascli –rn
/OMSAppControl

Restart OMSAppControl service. fshascli –rn

/OMSAppControl

Restart OMSAppControl service. fshascli –rn

/OMSAppControl

Restart OMSAppControl service. fshascli –rn

/OMSAppControl

Restart PMGeneric service. fshascli –rn /PMGeneric

Restart PMGeneric service. fshascli –rn /PMGeneric

Restart PMGeneric service. fshascli –rn /PMGeneric

Restart PMGeneric service. fshascli –rn /PMGeneric

Please do system restart.

Restart NWI3Adapter service. fshascli –rn

/NWI3Adapter
 V
a
l
u
e

i
n

t
h
e

p
r
e
v
i
o
OMS - LDAP Parameter Path

fsFragmentId=security, fsFragmentId=NWI3,
fsClusterId=ClusterRoot

omsParameterId=BTSFTPAlarmSetDelay,
omsFragmentId=OMSMeaHandler,
omsFragmentId=SS_RNCPM,
omsFragmentId=OMSRNC, fsFragmentId=OMS,
fsClusterId=ClusterRoot
omsParameterId=BackupEnabled,
omsFragmentId=OMSNMSFWriter,
omsFragmentId=SS_GenericPM,
omsFragmentId=OMSPlatform, fsFragmentId=OMS,
fsClusterId=ClusterRoot
omsParameterId=CANECloseCertUpdateTimerAdv,
omsFragmentId=Nwi3Certificate,
omsFragmentId=SS_Nwi3Certificate,
omsFragmentId=SW, fsFragmentId=OMS,
fsClusterId=ClusterRoot
omsParameterId=CANECloserCertUpdateTimerAdv,
omsFragmentId=Nwi3Certificate,
omsFragmentId=SS_Nwi3Certificate,
omsFragmentId=SW, fsFragmentId=OMS,
fsClusterId=ClusterRoot
omsParameterId=CRLPeriodicDownloadTimer,
omsFragmentId=Nwi3Certificate,
omsFragmentId=SS_Nwi3Certificate,
omsFragmentId=SW, fsFragmentId=OMS,
fsClusterId=ClusterRoot
fsCertManConfig=default, fsFragmentId=CertMan,
fsClusterId=ClusterRoot

fsdbName=DB_Alarm, fsFragmentId=DB,
fsClusterId=ClusterRoot

fsdbName=DB_CMPlan, fsFragmentId=DB,
fsClusterId=ClusterRoot

fsdbName=DB_CosNaming, fsFragmentId=DB,
fsClusterId=ClusterRoot

fsdbName=DB_Topology, fsFragmentId=DB,
fsClusterId=ClusterRoot

omsParameterId=DataStoringDelay,
omsFragmentId=OMSMeaHandler,
omsFragmentId=SS_RNCPM,
omsFragmentId=OMSRNC, fsFragmentId=OMS,
fsClusterId=ClusterRoot
omsParameterId=DeleteFilesAfterRead,
omsFragmentId=OMSBTSFileReader,
omsFragmentId=SS_MeasurementHandling,
omsFragmentId=OMSPlatform, fsFragmentId=OMS,
fsClusterId=ClusterRoot
omsParameterId=DeleteTemporaryFiles,
omsFragmentId=CMPlanManager,
omsFragmentId=SS_Planwagen,
omsFragmentId=OMSPlatform, fsFragmentId=OMS,
fsClusterId=ClusterRoot
omsParameterId=DeleteTemporaryFilesTimePeriod,
omsFragmentId=CMPlanManager,
omsFragmentId=SS_Planwagen,
omsFragmentId=OMSPlatform, fsFragmentId=OMS,
fsClusterId=ClusterRoot
omsParameterId=dwAlarmForUploadCompleted,
omsFragmentId=NELogManager,
omsFragmentId=SS_NELogManager,
omsFragmentId=OMSPlatform, fsFragmentId=OMS,
fsClusterId=ClusterRoot
omsParameterId=dwBTSLogObsolescenceTimeMins,
omsFragmentId=NELogManager,
omsFragmentId=SS_NELogManager,
omsFragmentId=OMSPlatform, fsFragmentId=OMS,
fsClusterId=ClusterRoot
omsParameterId=dwBTSUploadEnabled,
omsFragmentId=NELogManager,
omsFragmentId=SS_NELogManager,
omsFragmentId=OMSPlatform, fsFragmentId=OMS,
fsClusterId=ClusterRoot
omsParameterId=dwFlags, omsFragmentId=Any,
omsFragmentId=TraceConfig, omsFragmentId=System,
fsFragmentId=OMS, fsClusterId=ClusterRoot

omsParameterId=dwLogSizeInKB,
omsFragmentId=Any, omsFragmentId=TraceConfig,
omsFragmentId=System,
fsFragmentId=OMS,fsClusterId=ClusterRoot
omsParameterId=dwMaxConcurrentBTSUploads,
omsFragmentId=NELogManager,
omsFragmentId=SS_NELogManager,
omsFragmentId=OMSPlatform, fsFragmentId=OMS,
fsClusterId=ClusterRoot
omsParameterId=dwMaxPercentageDiskUsage,
omsFragmentId=NELogManager,
omsFragmentId=SS_NELogManager,
omsFragmentId=OMSPlatform, fsFragmentId=OMS,
fsClusterId=ClusterRoot
omsParameterId=dwNELogDaysSpan,
omsFragmentId=NELogManager,
omsFragmentId=SS_NELogManager,
omsFragmentId=OMSPlatform, fsFragmentId=OMS,
fsClusterId=ClusterRoot
fsnwi3N3CFId=LIST_ITEM_ID, fsFragmentId=mediator,
fsFragmentId=NWI3, fsClusterId=ClusterRoot

fsnwi3N3CFId=LIST_ITEM_ID, fsFragmentId=mediator,
fsFragmentId=NWI3, fsClusterId=ClusterRoot

fsnwi3N3CFId=LIST_ITEM_ID, fsFragmentId=mediator,
fsFragmentId=NWI3, fsClusterId=ClusterRoot

fsnwi3N3CFId=LIST_ITEM_ID, fsFragmentId=mediator,
fsFragmentId=NWI3, fsClusterId=ClusterRoot

fsnwi3N3CFId=LIST_ITEM_ID, fsFragmentId=mediator,
fsFragmentId=NWI3, fsClusterId=ClusterRoot

fsnwi3N3CFId=LIST_ITEM_ID, fsFragmentId=mediator,
fsFragmentId=NWI3, fsClusterId=ClusterRoot

fsnwi3N3CFId=LIST_ITEM_ID, fsFragmentId=mediator,
fsFragmentId=NWI3, fsClusterId=ClusterRoot
fsnwi3N3CFId=LIST_ITEM_ID, fsFragmentId=mediator,
fsFragmentId=NWI3, fsClusterId=ClusterRoot

fsnwi3N3CFId=LIST_ITEM_ID, fsFragmentId=mediator,
fsFragmentId=NWI3, fsClusterId=ClusterRoot

fsnwi3N3CFId=LIST_ITEM_ID, fsFragmentId=mediator,
fsFragmentId=NWI3, fsClusterId=ClusterRoot

fsnwi3N3CFId=LIST_ITEM_ID, fsFragmentId=mediator,
fsFragmentId=NWI3, fsClusterId=ClusterRoot

fsnwi3N3CFId=LIST_ITEM_ID, fsFragmentId=mediator,
fsFragmentId=NWI3, fsClusterId=ClusterRoot

fsnwi3N3CFId=LIST_ITEM_ID, fsFragmentId=mediator,
fsFragmentId=NWI3, fsClusterId=ClusterRoot

fsnwi3N3CFId=LIST_ITEM_ID, fsFragmentId=mediator,
fsFragmentId=NWI3, fsClusterId=ClusterRoot

fsnwi3N3CFId=LIST_ITEM_ID, fsFragmentId=mediator,
fsFragmentId=NWI3, fsClusterId=ClusterRoot

fsAlarmProcessorConfigurationId=Default,
fsAlarmProcessorId=AlarmProcessor1,
fsFragmentId=AlarmProcessors,
fsFragmentId=AlarmMgmt, fsClusterId=ClusterRoot
omsParameterId=maxQuantityPassiveSWSets,
omsFragmentId=RemoteSW, omsFragmentId=System,
fsFragmentId=OMS, fsClusterId=ClusterRoot

omsParameterId=MinimumFreeSpaceNeededForBacku
p, omsFragmentId=OMSBackup,
omsFragmentId=System, fsFragmentId=OMS,
fsClusterId=ClusterRoot
fsFragmentId=security, fsFragmentId=NWI3,
fsClusterId=ClusterRoot
fsFragmentId=security, fsFragmentId=NWI3,
fsClusterId=ClusterRoot

omsParameterId=NELTEActivateRetryCount,
omsFragmentId=CMPlanManager,
omsFragmentId=SS_Planwagen,
omsFragmentId=OMSPlatform, fsFragmentId=OMS,
fsClusterId=ClusterRoot
omsParameterId=NEBaseTimeout,
omsFragmentId=CMPlanManager,
omsFragmentId=SS_Planwagen,
omsFragmentId=OMSPlatform, fsFragmentId=OMS,
fsClusterId=ClusterRoot
omsParameterId=NELTEDownloadRetryCount,
omsFragmentId=CMPlanManager,
omsFragmentId=SS_Planwagen,
omsFragmentId=OMSPlatform, fsFragmentId=OMS,
fsClusterId=ClusterRoot
omsParameterId=NERetryCount,
omsFragmentId=CMPlanManager,
omsFragmentId=SS_Planwagen,
omsFragmentId=OMSPlatform, fsFragmentId=OMS,
fsClusterId=ClusterRoot
omsParameterId=NERetryCountForEmergency,
omsFragmentId=CMPlanManager,
omsFragmentId=SS_Planwagen,
omsFragmentId=OMSPlatform, fsFragmentId=OMS,
fsClusterId=ClusterRoot
omsParameterId=NERollbackRetryCount,
omsFragmentId=CMPlanManager,
omsFragmentId=SS_Planwagen,
omsFragmentId=OMSPlatform, fsFragmentId=OMS,
fsClusterId=ClusterRoot
omsParameterId=NELTEUploadRetryCount,
omsFragmentId=CMPlanManager,
omsFragmentId=SS_Planwagen,
omsFragmentId=OMSPlatform, fsFragmentId=OMS,
fsClusterId=ClusterRoot
omsParameterId=NetActNotifyEnabled,
omsFragmentId=NELogManager,
omsFragmentId=SS_NELogManager,
omsFragmentId=OMSPlatform, fsFragmentId=OMS,
fsClusterId=ClusterRoot
omsParameterId=szIPAddress, omsFragmentId=OMS,
omsFragmentId=CUAccess, omsFragmentId=Network,
omsFragmentId=System, fsFragmentId=OMS,
fsClusterId=ClusterRoot
omsParameterId= NotifReceiptCheckStart ,
omsFragmentId=OMSMeaHandler,
omsFragmentId=SS_RNCPM,
omsFragmentId=OMSRNC, fsFragmentId=OMS,
fsClusterId=ClusterRoot
omsParameterId= NotifReceiptCheckStep ,
omsFragmentId=OMSMeaHandler,
omsFragmentId=SS_RNCPM,
omsFragmentId=OMSRNC, fsFragmentId=OMS,
fsClusterId=ClusterRoot
omsParameterId=OmsNicBandwidthAbsoluteLimit,
omsFragmentId=TrafficControl,
omsFragmentId=Network, omsFragmentId=System,
fsFragmentId=OMS, fsClusterId=ClusterRoot
omsParameterId=OmsNicBandwidthLimitStatus,
omsFragmentId=TrafficControl,
omsFragmentId=Network, omsFragmentId=System,
fsFragmentId=OMS, fsClusterId=ClusterRoot
omsParameterId=OmsNicBandwidthRelativeLimit,
omsFragmentId=TrafficControl,
omsFragmentId=Network, omsFragmentId=System,
fsFragmentId=OMS, fsClusterId=ClusterRoot
omsParameterId=OverloadControlWindowFaultManage
mentTimeout, omsFragmentId=OMSAppControl,
omsFragmentId=SS_OMSAppControl,
omsFragmentId=OMSPlatform, fsFragmentId=OMS,
fsClusterId=ClusterRoot
omsParameterId=OverloadControlWindowLogViewerTi
meout, omsFragmentId=OMSAppControl,
omsFragmentId=SS_OMSAppControl,
omsFragmentId=OMSPlatform, fsFragmentId=OMS,
fsClusterId=ClusterRoot
omsParameterId=OverloadControlWindowSWVersionVi
ewerTimeout, omsFragmentId=OMSAppControl,
omsFragmentId=SS_OMSAppControl,
omsFragmentId=OMSPlatform, fsFragmentId=OMS,
fsClusterId=ClusterRoot
omsParameterId=OverloadControlWindowTopologyBro
wserTimeout, omsFragmentId=OMSAppControl,
omsFragmentId=SS_OMSAppControl,
omsFragmentId=OMSPlatform, fsFragmentId=OMS,
fsClusterId=ClusterRoot
omsParameterId=PMFileBufferAlarmCancelThreshold,
omsFragmentId=GenericPMCtrl,
omsFragmentId=SS_GenericPM,
omsFragmentId=OMSPlatform, fsFragmentId=OMS,
fsClusterId=ClusterRoot
omsParameterId=PMFileBufferAlarmEnabled,
omsFragmentId=GenericPMCtrl,
omsFragmentId=SS_GenericPM,
omsFragmentId=OMSPlatform, fsFragmentId=OMS,
fsClusterId=ClusterRoot
omsParameterId=PMFileBufferAlarmSetDelay,
omsFragmentId=GenericPMCtrl,
omsFragmentId=SS_GenericPM,
omsFragmentId=OMSPlatform, fsFragmentId=OMS,
fsClusterId=ClusterRoot
omsParameterId=PMFileBufferAlarmSetThreshold,
omsFragmentId=GenericPMCtrl,
omsFragmentId=SS_GenericPM,
omsFragmentId=OMSPlatform, fsFragmentId=OMS,
fsClusterId=ClusterRoot
omsParameterId=PMOverloadAlarmCancelThreshold,
omsFragmentId=OMSMeaHandler,
omsFragmentId=SS_RNCPM,
omsFragmentId=OMSRNC, fsFragmentId=OMS,
fsClusterId=ClusterRoot
omsParameterId=PMOverloadAlarmEnabled,
omsFragmentId=OMSMeaHandler,
omsFragmentId=SS_RNCPM,
omsFragmentId=OMSRNC, fsFragmentId=OMS,
fsClusterId=ClusterRoot
omsParameterId=PMOverloadAlarmSetThreshold,
omsFragmentId=OMSMeaHandler,
omsFragmentId=SS_RNCPM,
omsFragmentId=OMSRNC, fsFragmentId=OMS,
fsClusterId=ClusterRoot
omsParameterId=PMOverloadAlarmWindow,
omsFragmentId=OMSMeaHandler,
omsFragmentId=SS_RNCPM,
omsFragmentId=OMSRNC, fsFragmentId=OMS,
fsClusterId=ClusterRoot
omsParameterId=RUIMAutomaticActivation,
omsFragmentId=RUIM, omsFragmentId=System,
fsFragmentId=OMS, fsClusterId=ClusterRoot

omsParameterId=szIPAddress, omsFragmentId=OMSS,
omsFragmentId=CUAccess, omsFragmentId=Network,
omsFragmentId=System, fsFragmentId=OMS,
fsClusterId=ClusterRoot
omsParameterId=TLSModeFT, omsFragmentId=TLS,
omsFragmentId=Network, omsFragmentId=System,
fsFragmentId=OMS,fsClusterId=ClusterRoot

omsParameterId=TLSModeOM, omsFragmentId=TLS,
omsFragmentId=Network, omsFragmentId=System,
fsFragmentId=OMS, fsClusterId=ClusterRoot
omsParameterId=dwControllerUploadEnabled,
omsFragmentId=NELogManager,
omsFragmentId=SS_NELogManager,
omsFragmentId=OMSPlatform, fsFragmentId=OMS,
fsClusterId=ClusterRoot