We are IntechOpen,

the world’s leading publisher of

Open Access books
Built by scientists, for scientists

6,200
Open access books available
169,000
International authors and editors
185M
Downloads

Our authors are among the

154
Countries delivered to
TOP 1%
most cited scientists
12.2%
Contributors from top 500 universities

Selection of our books indexed in the Book Citation Index

in Web of Science™ Core Collection (BKCI)

Interested in publishing with us?

Contact [email protected]
Numbers displayed above are based on latest data collected.
For more information visit www.intechopen.com
Chapter

Basic Principles of Colour

Measurement and Colour
Matching of Textiles and Apparels
Pubalina Samanta

Abstract

This book chapter covers basic principles of quantitative measurement and

analysis of surface colour parameters and surface appearance of undyed/dyed tex-
tile materials and finally matching of colours with standard samples of any textiles.
Surface colour parameters of textile materials change with different chemical
processing including bleaching, dyeing and finishing and need to measure it quan-
titatively for understanding the effect of different chemical processes/dyes and
auxiliaries and finishes. So, CIE-1976 equations for measurement of Tristimulus
values, surface colour strength, colour differences, Metamerism index, colour dif-
ference index as well as specific formulae for measuring Whiteness Index,
Yellowness Index, Brightness Index and the theory of colour match prediction are
discussed here. One Case study of colour match prediction for a specific case is also
shown. Finally, the importance of single constant measurement of surface color
parameters for coloured textiles and practical cares for database preparation and
colour measurement and match prediction for textile and apparel products are
deliberated. Apparel industry is very much dependent on colour psychology and
colour preferences of customers in different seasons and occasions and hence, it is
important to measure all surface colour parameters of textile materials to choose
perfectly matched coloured textiles for making any garment.

Keywords: surface colour strength, Tristimulus values, Total colour differences,

colour difference index, Metamerism, whiteness-yellowness and brightness indices.
Computer aided colour matching

1. Introduction

Colour and aesthetics are as important as its various physical properties for
textiles/garments, leather, moulded plastics,and products of various other fields.
The ability to integrally colour(dyeing and Printing) textiles, leather, plastic
moulded articles has an important edge over others non polymeric rigid hard
materials like metals etc.
Matching of colours and imitate texture, especially in specific textiles of differ-
ent fibres and blends is crucial in many of its apparel applications. The task becomes
more difficult when colours need to be exactly matched with standard colour yield
desired with endurable criteria for acceptable colour fastness to wash, rubbing, light

1
Colorimetry

and perspiration etc. for different textiles/plastics and polymer products. So,
understanding Theory of colour measurement, quantification, for well defined
applications of different dyes/pigments on different textiles materials has become a
must for the textile or leather dyers/printers and plastics injection moulder/wall
paints etc.
Day by day, more and more concern of consumers on colour matching for
consumers’ textiles and live-style products of apparels and furnishings, bed linen
and auto-mobile (car) Interiors, appliances and along with polymer/plastic
assemblies, are pushing the dyed/printed coloured textile product manufacturer to
develop their products with more precision colour matching with least
meta-merism.
In order to understand the colour we have to know, how the colour is perceived.
The perception of colours [1] involves the interaction of three elements. (i) source
of light, (ii) an object and (iii) human eye.

2. Colour theory

Colour can be broadly defined as the physio-psychometric effect on the brain of

an observer from reflected wavelength of an object, when that object is viewed in
presence of a definite light source.
Colour theory meant a Standardised scientific method with specific mathemati-
cal/empirical formula with arrangement of incidence of light/standard illuminant
for absorption and reflection of the colour on and from the object and then
detecting folowed by measurement of colour value specific reflactance or any other
quantified values to record and communicate colour information for reproducibility
and matching.

2.1 CIE definition 845-02-18 of perceived colour

As per CIE definition 845-02-18: (perceived) colour may be defined [2] or

perceived as “ Attribute of a visual perception consisting of any combination of
chromatic and achromatic content. This attribute can be described by chromatic
color names such as yellow, orange, brown, red, pink, green, blue, purple, etc., or
by achromatic color names such as white, gray, black, etc., and qualified by bright,
dim, light, dark etc., or by combinations of such names [Unquote].
Human Perception of colour usually appear to describe a colour in terms of
amount of RGB (Red, Green and Blue) sensation of human eye as an additive colour
mixing system (as shown in Figure 1) distinguish among qualitative and geometric
differences of colour perceptions by its predominating Hue (predominating
Reflected wavelength observed), Value (Light or Dark i.e. White or Black

Figure 1.
Schematic display of colour observed from RGB primary colour stimuli with standard illuminant by a standard
observer /detector.

2
Basic Principles of Colour Measurement and Colour Matching of Textiles and Apparels
DOI: http://dx.doi.org/10.5772/intechopen.101442

respectively) and chroma (Strength or Concentrations of Coloured mol.) [1]

with/without associated brightness/dullness and uv absorption.
Thus, Colour of any object can be considered as an physio-psychological illusion
of reflected radiation / visible light from a substance/object after incidence of light
on it, which is to be detected in exact quantitative terms by amount of RGB in it
(Figure 1), while, colorimetry is the measurement and evaluation technique of
colour value in any quantifiable terms by which this physio-psychological sensation
of our eyes can be converted to the actual physical measurement of colour values
either in solution or in solids in some sensory values of primary colours.
If any one want to buy a skirt or a pair of slacks to match a jacket, one cannot
match the colour by memory — he/she has to take the jacket with him/her to match
it visually by judging colour by eye measurement in the store itself. it may happen
that in some cases, the store light is insufficient and faulty matching by eyes results,
So, one has to match it also under standard and sufficient incandescent light in the
dressing room and and also in the outdoor sunlight too.
Three fundamental components of understanding or measuring or matching any
colour:

• light sources /standard illuminant

• objects / samples illuminated by standard light

• observers /detector to record colours reflected from it

Most Important and commercially useable Two of the major Colour

quantification systems are:

• Munsell Colour Theory -hue, value and chroma

• The CIE Theory of Colour -Tristimulus values (X, Y and Z) and CIE L*, a*and
b* values

The CIE Theory of Colour 1931 updated in 1976 [1.2] is in wide commercial use
for textile’s colour communication and hence it has significant importance in
apparel sector and is described below.

2.2 CIE 1931 standard theory of colour

The Commission Internationale de l’Éclairag e (CIE) has recommended x(l),

y(l), z(l) for lÎ [360 nm, 830 nm] in 1 nm steps for distinguishing colour based on
tristimulas values, which are well accepted/.
Over a wide range of conditions of observation, many colour stimuli can be
matched in colour completely by additive mixtures of three fixed primary colour
stimuli (RGB) combine linearly, symmetrically, and transitively and may be
expressed as X (stimuli of Red Primary), Y (stimuli of Green primary), and Z
(*Stimuli of Blue Primary) as three coordinates called Tristimulus values (X, Y
and Z) or stimuli of any colour observed under standard illuminant under standard
detector / observer, based on reflected contributions of R G B primaries from any
object (Figure 1) having spectral sensitivity of RGB primary stimuli (as shown in
Figure 2a) and actual Tristimulus values of any object (X, Y and Z values, as per
formulation shown in Figure 2b).
Thus, a monochromatic colour stimulus (Ql) of wavelength L, it can be
represented /expressed as

3
Colorimetry

Figure 2.
(a): Spectral sensitivity of human eyes of RGB primary Stimulli and (b): Resultant actual measurement of
reflectance values and corresponding Tristimulus values of any object.

Figure 3.
a: CIE 1931 chromaticity diagram showing b: CIE 1931 chromaticity diagram all predominating visible hues
at 380-700 nm (coloured) showing x and y coordinates.

Q l ¼ X l R þ Y l G þ Rl B,

where Rl, Gl, and Bl are the spectral tristimulus values of Ql.
Consequently, the CIE 1931 chromaticity diagram [1–3] is not a perceptually
uniform chromaticity space from which the perception of chromaticity can be
derived, where (Figure 3a and b)

x ¼ X=ðX þ Y þ Z Þ, (1)
y ¼ Y=ðX þ Y þ Z Þ, (2)
z ¼ Z=ðX þ Y þ ZÞ, (3)
and x þ y þ z ¼ 1 (4)

and also z ¼ 1‐x‐y .



4
Basic Principles of Colour Measurement and Colour Matching of Textiles and Apparels
DOI: http://dx.doi.org/10.5772/intechopen.101442

Hence there is no need to plot a three dimensial x,y and z diagram, rather the
2 dimensional chromaticity coordinate plot (Figure 3a or b) is sufficient to get x,y
& z values from x vs. y plot of 2 dimensional CIE chromaticity diagram [1–3].
As per 1976 CIE L*a*b* colour space, L*, a* and b* values for comparing colour
differences in betrween two samples of same or similar textile fabrics n be
represented by ∆L*, ∆a* and ∆b* values [1–3].
CIE 1976 lightness/darkness is represented by, L* (L = 0 black and L-100
white), more or less similar to lightness distribution to the Munsell Value scale and,
CIE 1976 scale of redness (a* ve) /greenness (a* ve) is represented by a* and CIE
1976 scale of yellowness (b*+ve) /blueness (b* ve) is represented by b*, and 1976
CIE L*a*b* colour space diagram represent total colour differences value by ∆E or
∆E * (as shown in Figures 4 and 5).

Where, L ∗ ¼ 116ðY=Yo Þ1=3 –16, ΔL ∗ ¼ L ∗ 1 –L ∗ 2 (5)

h i
a ∗ ¼ 500 ðX=Xo Þ1=3 –ðY=Yo Þ1=3 , Δa ∗ ¼ a ∗ 1 –a ∗ 2 (6)
h i
b ∗ ¼ 200 ðY=Yo Þ1=3 –ðZ=Zo Þ1=3 , Δb ∗ ¼ b ∗ 1 –b ∗ 2 (7)

Figure 4.
CIE-L* a* b* system of colour difference plot to determine ∆L*, ∆a* and ∆b* values of a pair.

Figure 5.
Example of metameric match under two different illuminant (day light and Fluoroscent light conditions.

5
Colorimetry

Chroma, (psychometric chroma) values in CIELAB colour space [1–3] was

calculated as follows:
1=2
CðabÞ ∗ ¼ a ∗ 2 þ b ∗ 2 , ΔC ∗ ¼ C ∗ 1ðabÞ –C ∗ 2ðabÞ (8)


Where, C*1(ab) and C*2(ab) are the chroma values for standard and produced
sample.
CIE 1976 metric Hue-Difference (∆H) for CIELAB system [1–3] was calculated
as follows:
h i1=2
ΔHab ¼ ðΔEab ∗ Þ2 ðΔL ∗ Þ2 ðCab ∗ Þ2 (9)

Total Colour Differences [1–3]:

i1
2 =2
h
ΔE ∗ ¼ ðΔL ∗ Þ2 þ ðΔa ∗ Þ2 þ ðΔb ∗ Þ (10)

As per Kubelka Munk Equation [1–3]. Surface colour Strength (K/S value) of
Coloured flat surface is:

Co‐efficient of absorption
K=S ¼
Co‐efficient of scattering
(11)
ð1 Rλ max Þ2
¼ ¼ αCD
2Rλ max

Where K is the coefficient of absorption; S, the coefficient of scattering;

and Rʎmax, is the Reflectance value at maximum absorbance wavelength (λmax) and
CD is the dye concentration and α is the constant.
For use mixture of colourants to obtain a compound shades on the surface of
textiles or similar substrate, as K/S is additive in nature, it can be represented as
follows:

ðK=SÞMAX ¼ ðK=SÞsubsþ ðK=SÞ1 þ ðK=SÞ2 þ ðK=SÞ3 þ … …

¼ ðK=SÞsubs þ λ1 C1 þ λ2 C2 þ λ3 C3 þ … … : (12)

Moreover, plot of dye concentration Vs K/S value is linear in relation and is

easier to predict for any unknown concentration of dyes, while plot of Reflectance
vs. dye concentration is non linear in relation and is difficult to predict and hence
K/S is an important surface colour measuring criteria of textiles, against application
of increase or decrease in dye concentration on same or similar fabrics.
For coloured textile materials, it may be presumed that dye molecules are not
contributing to change in scattering and therefore K integrated over visible wave-
length is the total sum of absorption of dyestuff and textile substrate (so, if sub-
strate is not changed, scattering is not changed). Therefore, surface colour strength
i.e. K/S value is directly proportional with concentration of dye molecules and the
scattering value of the dyed textile sample is not dependent on the concentration of
dye stuff (but that is not true for the case of pigments in paint or binded over textile
substrate with binder chemicald and fixed on the surface of the materials). So, for
textile substrate, it is single constant theory of Colour Matching applicable for all
textile materils.
Hence, for any textile surface, for the particular dyed/coloured textile sample
(Fibre, Yarn and Fabric construction and type and amount of surface deposited

6
Basic Principles of Colour Measurement and Colour Matching of Textiles and Apparels
DOI: http://dx.doi.org/10.5772/intechopen.101442

(coated or impregnated)finish remains un-altered), and scattering values remains

constant always, if textile fabric used is not changed.
Thus higher is the K/S value, meant higher is the absorption value, meant higher
absorption value signifying or indicating higher surface dye uptake, governed by
following formulae.

ðK=SÞmix ¼ C1 ðK=SÞ1 þ C2 ðK=SÞ2 þ C3 ðK=SÞ3 (13)

ðK=SÞdyed substrate ¼ C0 ðK=SÞun dyed substrate þ C1 ðK=SÞ d1 þ C2 ðK=SÞd2 þ C3 ðK=SÞd3
(14)

Finally, reflectance Vs. dye concentration is not linear & is difficult to

interpolate or curve fitting.
While K/S Vs. dye concentration is linear can be interpolated thus can be used in
computerised colour measurement and matching software.

2.3 Principles of colour matching of dyed textiles

A colour match between two sets of samples means:

Colour of produced sample = Colour of given standard sample i.e. (XSL,YSL,ZSL)
values of produced sample = (XSD,YSD,ZSD) values of given standard sample while
X,Y & Z are the tristimulus value of produced Sample (SL) and Standard (SD)
sample Also match may be predicted or judged [1–3] by (Reflectance)SL of pro-
duced sample integrated at 400 to700 nm = (Reflectance)SD of standard sample
integrated at 400 to 700 nm or (K/S) SL values of produced sample = (K/S) SD value
of standard sample, where K/S = α CD and K/S values (as per kubelka munk
Equation [1–3]) as stated above), is:

Co‐efficient of absorption
K=S ¼
Co‐efficient of scattering
(15)
ð1 Rλ max Þ2
¼ ¼ αCD
2Rλ max

For a ternary mixture of colourants/dyes to obtain any particular compound

shade on textiles, three equations are to be solved as a function of dye concentra-
tions of the colourants (1,2,3 or n) and have to determine tristimulus values or K/S
Values obtained through reflectance measurement of samples to match. More over
K/S value being additive and dye concentration vs. K/S being linear in nature, the
resultant K/S value of a dyed sample (dyed with mixture of three different dyes
(d1, d2 and d3) in respective concentrations (c1, c2 and c3) is represented by
following matrix equations:

f x ð c1 ; c2 ; c3 Þ ¼ X ðK=SÞmix ¼ c1 ðK=SÞd1 þ c2 ðK=SÞd2 þ c3 ðK=SÞd3

f y ð c1 ; c2 ; c3 Þ ¼ Y and ðK=SÞdyed substrate ¼ c0 ðK=SÞun dyed substrate þ c1 ðK=SÞd1
f z ð c1 ; c2 ; c3 Þ ¼ Z þc2 ðK=SÞd2 þ c3 ðK=SÞd3
(16)

Where, X, Y and Z are the tri-colorimetric tristimulus values of samples pro-

duced i.e. to be matched finally and c1,c2, c3 are the exact concentration of amount
of dyes/colourants required.
In practical ceases, the reflectance values of given standard sample at 400 to
700 nm are determined from given standard coloured solid textile fabric surface

7
Colorimetry

and the obtained results of reflectance values at different wave length in visible
region are processed in computer aided colour matching software for matching
X, Y and Z values of produced samples or simply by comaparing the total inte-
grated K/S values at 400–700 nm wavelength (visible range) for ultimate checking
of colour matching of textiles in terms of allowable limits (tolerences) of colour
difference values of ∆ L*, ∆a* and ∆b* values representing 1976 CIE L*a*b*
colour space diagram and in terms of allowable limit of total colour differences
value represented by ∆E / ∆E *.
A textile match however should be ideally be an isomeric match i.e. match under
all illuminant. But in actual practice, when two coloured sample show a match of
colour under one illuminant may not match under other illuminantand this differ-
ence of match under specific two conditions of different illuminant is termed as
illuminant based metameric match. Besides variation of illumainnat, there are other
different types of metamerism for change of conditions of colour measurement, as
follows, arised during colour matching under varying ambience of any one factor or
others [1–3]:
Types of metamerism:

• Illuminant metamerism: example: daylight and D65 simulation fluorescent lamp

• Object metamerism: example: metameric inks (see metamerism kit)

• Observer or Sensor metamerism: example: Instrumental scanner and human

visual perception

• Complex metamerism and Instrument metamerism: example:two inks/ dyed

clothes measured under two different instruments.

Colour matching is therefore based on to find a Least metameric match where,

General metamerism index [1–3] is as given below:

ðΔRxÞ2 ðΔRyÞ2 ðΔRzÞ2

P P P
General metamerism Index ¼ þ þ (17)
X2 Y2 Z2

Where ∆R = Difference in reflectance between pair of metamer samples;

x,y, z = CIE standard observer colour function X, Y, Z = CIE tristimulas value
normally taken for illuminant C.
The Metamerism-Index (MI) shows the probability that two samples will show
the same colour difference under two different illuminants (represented by the first
and second illuminant) or under two different instruments or under any two dif-
ferent conditions of colour measurements. CIE LAB i.e. LABD metamerism index
[1–3] is represented as:
h i1=2
2
MIðLABDÞ ¼ ðΔL1 ∗ ΔL2 ∗ Þ2 þ ðΔa1 ∗ ðΔa2 ∗ Þ2 þ ðΔb1 ∗ ðΔb2 ∗ Þ (18)

∆L1*, ∆a1*, and ∆b1*are the Delta CIELab* colour coordinates between
Standard and Sample for the first illuminant and ∆L2*, ∆a2*, and ∆b2*are the Delta
CIELab* colour coordinates between Standard and Sample for the second illuminant
Interpretation:
When, MI (metamerism index) is low, the colour difference between the sample
pair (standard vs. produced) is the more closer and similar, for different conditions
of measurement even under different illuminants.

8
Basic Principles of Colour Measurement and Colour Matching of Textiles and Apparels
DOI: http://dx.doi.org/10.5772/intechopen.101442

Reflectance Spectrophotometers are very effective instrument in measuring and

recording colours of any solid substrate / textiles from its substrate. All measurements
are done by CIE 1976 System [1–3], which is commonly used in textile and other
colour related industry.
The accuracy of colour matching of textiles depend on the set of tolerance limits
[1–3] for ∆ L*, ∆a*, ∆b* and ∆E / ∆E *. values under pre decided illuminant as
standard illuminant, which is another significant task. It is generally thumb rule
from practical observations that DE values below or within 1.0 are acceptable match
i.e. DE values above 1is not a good match at all. Moreover, during dyeing in
industry, all dyers and other relevant people likes to create more stringent tolerance
values for colour matching of textile substrate preferably DE value are to be within
0.7 only. Setting of colour matching tolerences in terms of Colour differences values
are discussed later in item 3.1 in details.
Thus these colour difference data has many benefits to the dyers entailing how
much it is darker or light, how much it is redder or greener or how much it is bluer
and yellower, when the shades of two nearly match samples are compared. Thus,
Human eye estimated perception of colour differences between two or more objects
against any standard shade, can be quantified to numerical values of colour differ-
ences in terms of total colour differences (DE values) and also in terms of DL(light
and dark), Da (redness and greenness) and Db (blueness and yellowness). This has
made easier to match/compare colours of textiles of a nearly matched two dyed
textile samples(Standard shades given vs. Produced shade) by determining what are
the colour differences between the two, leaving behind opportunity by batch cor-
rection either manually or instrumentally [1–3] to help different dyers to add or
substract particular colour to get better match.

2.3.1 Batch Correction in subsequent iteration to improve match precision

The reformulation of batch correction issue for computing the incremental value
of concentration of dyes by each iteration at each stage may be represented by the
following matrix as follows [4]:

∂C1 ∂C1 ∂C1

ΔC1 ¼ ΔX þ ΔY þ ΔZ (19)
∂X ∂Y ∂Z
∂C2 ∂C2 ∂C2
ΔC2 ¼ ΔX þ ΔY þ ΔZ (20)
∂X ∂Y ∂Z
∂C3 ∂C3 ∂C3
ΔC3 ¼ ΔX þ ΔY þ ΔZ (21)
∂X ∂Y ∂Z

2.4 Colour measuring instruments

Photometry is the most common analytical technique used in measurement of

colour in solution/solid in the laboratory. It is designed to measure the intensity of
transmitted /reflected beam of light through the coloured solution/solid. Different types
of instruments with Photometric principles are applied to the different ways of analysis
of coloured materials /substrate/solution by different techniques [5] as listed below:

a. Where absorbed or transmitted light is measured:

• Colorimeter

• UV–VIS Absorbance Spectrophotometer

9
Colorimetry

• Atomic absorption spectrophotometer, and

• Turbidometer

b. Where emitted light is measured: Flame photometry

c. Where reflected light is measured: UV VIS Reflectance Spectrophotometer

In analytical chemistry or in textile analytical chemistry laboratory, colorimetry

based on UV VIS Spectrophotometer technique is used to determine the concentra-
tion of coloured compounds (analytes) in sample of a coloured solution or in solid
coloured sample of textiles or leather or plastics or polymer film or any other
chemical compounds” at visible spectrum of light (400–700 nm as VIBGYOR as
described in Figure 6), is observed in the visible spectrum of electromagnetic
radiation, emitted in the form of dominating wave lengths emitting VIBGYOR
wavelengths ranging from 400 nm to 700 nm. Similarly UV Light /sunlight radia-
tion usually is observed to have UV radiation of 180 to 380 /400 nm wave length, as
UV-A, UB-B, and UV-C type.

Figure 6.
Major wavelength from incident white light dominating at visible range.

10
Basic Principles of Colour Measurement and Colour Matching of Textiles and Apparels
DOI: http://dx.doi.org/10.5772/intechopen.101442

UV VIS Spectrophotometer technique of colour measurement are done by

following two principles:

a. UV VIS Absorbance Spectrophotometry: (for determining UV–VIS

wavelength scan pattern of a particular coloured compounds/dyes and to
determine concentration of pure coloured compounds/dyes (analytes) in
sample solution(dilute solution)

b. UV VIS Reflectance Spectrophotometry: (for determining UV or VIS

wavelength scan results of a solid materials surface (dyed/printed
coloured textiles, leather /paper, cosmetics etc) of any particular
coloured materials /dyes etc and to determine concentration of surface
colour strength of any of the said coloured materials’ surface for a solid
sample(non- destructive) [6].

This chapter mainly covers the basic principles of analysis of surface colour
parameters vis a vis other appearance properties of the surface of solid textile
materials and associated colour difference parameters by using Reflectance Spec-
trophotometer in terms of specific 1931 CIE and 1976 CIE formulae [1–3] for
determination of all specific Surface colour parameters of textile materials, changes
with or without different chemical processing and computer aided colour match
prediction theories and practices [7, 8].

2.5 Reflectance spectrophotometer

Reflectance Spectrophotometer is an human eye simulated UV–VIS double beam

spectrophotometer instrument for measuring colour of solid textile surface under
standard illuminant and standard observer with or without Uv Absorption included
and Excluded to measure reflectance, surface colour strength and to compare the
colour differences of two sets of samples nearly to match or unmatched/matched
coloured samples and also for storing and analysis of database of colour values of
different textile dyes applicable to different textile substrate and its use for com-
puter aided colour match prediction at finger tips with specific allowable limits of
∆L*, ∆a* and ∆b* and ∆E * values of colour differences as well as Studies on quality
checking of Dyes, effect of dyebath additives, dyeing process variables and UV
absorbance criteria of dyes / additives and effect of UV-absorbers/Optical bright-
eners on textile fabric under given treatment conditions and after care treatment/
washability etc.

2.6 Diagram of Relecatance spectrophotometer and its working principles

In UV–VIS reflectance spectrophotometer based on measuring reflectance of the

solid sample for measuring different colour parameters for quality control and
colour matching purpose, there is tungsten light source, which acts as source of
monochromatic incidence light and it falls on the opaque surface of the solid sample
at a particular incident angle to reflect at the same angle for specular reflectance
component and also reflects the incident light all around in diffused form at all
angles for non-specular reflectance inside the integrating spehere. THere are spec-
ular component in and out arrangement with UV component in and out arrange-
ment for specific requirement of setting ofv the instrument. Led detector situated in
the inside circumference of the integrating sphere detects the total reflectance
values at all diffused angles as well as at specific specular reflectance angle and the
amount of reflected light intensity is measured and shown as the reflectance values

11
Colorimetry

Figure 7.
Schematic diagram of working of UV–Vis spectrophotometer.

of sample at different wave length. Finally from reflectnace values obtianed for any
sample, it calculates other colour parameters as per CIE 1976 formulae [1–3] and
other formulae as per software inserted/installed for it for the data processing in a
suitable computer system for computer aided colour measuring and also for textile
match prediction system using pre-fed data base of textile dyes.
Usually a double beam UV VIS reflectance spectrophotometer, the incident light
beam is first split into two parts by a half mirror as two light beam called double
beam. One light beam falls /passes on the sample mounted and the other light beam
falls (for reflectance mode) /passes (for transmission mode) through a control
sample panel. This system of double beam eliminates the problems of interference
from control sample and normalises the variations in reflected /transmitted light
intensity readings uncreasing accuracy of the instrument reading, as the final
reflectance/ transmittabce/absorbance values are taken as the differences between
the readings of two reflected/transmitted beams of light intensity recorded.
The semicircular LED Detector inside the integrating sphere measures both the
two reflected/transmitted light intensity alternately and gets its processed in
computerised processor to give final reading. However, in some UV–VIS spectro-
photometer, a second detector is separately installed to measure the intensity of the
two beams separately. Thus, the major instrumental parts of an UV–VIS Double
Beam Reflectance Spectrophotometer are shown in Figure 7 indicating the position
of light source, diffraction grating, monochromator, sample cell/ integrating sphere,
detector and integrator and computerised recorder. The instrument changes the
light source from visible to UV light at about 350 nm by a mechanically moving
mirror, as shown in Figure 7.
The diffused reflection shows total effect of incident light including specular
reflection in integrating sphere diffraction, which may be excluded by opening a
port at particular angle without detecting the specular reflections in UV–Vis reflec-
tance spectrophotometer and different types of solid samples with varying surface
and texture show variation in reflectance values, effecting surface colour strength,
as shown in Figure 8.
Sphere Geometries of illumination and viewing in reflectance spectrophotome-
ter [7, 8] is very important here. It is based on mesaurement of Reflectance of dyed
samples of textiles. On a glossy surface there are mirror-like (specular) reflections
and there are more reflections in the case of diffuse light sources. Figure 9 shows
the effect of transmission mode and total reflection mode of integrating sphere of in

12
Basic Principles of Colour Measurement and Colour Matching of Textiles and Apparels
DOI: http://dx.doi.org/10.5772/intechopen.101442

Figure 8.
Schematic diagram of optical system of UV–Vis reflectance spectrophotometer.

Figure 9.
Schematic diagram of working of integrating shere type optical system in UV–Vis reflectance spectrophotometer.

UV–Vis reflectance spectrophotometer, showing provision of specular component

inclusion and exclusion by keeping specular port off and on (close or open).
Since the colour of the illuminant is white, specular reflections add white, with
the effect of de-saturating the colour. Textiles or any non-metallic glossy surfaces
look more saturated in directional than in diffuse illumination, while matte surfaces
scatter the light diffusely — matte surfaces usually look less saturated than glossy
surfaces.
Most of the textile surfaces are between glossy and matte and hence in reflec-
tance spectrophotometer, diffuse illumination is provided by integrating spheres
with provision of gloss traps /lid at regular reflection points to include or exclude
specular/regular reflectance in instrumental set up. REflactance spectrophotometer
Instruments with 45/0 and 0/45 geometry are less critical and give better results and
accuracy. ASTM recommends [1–4] use the geometry that minimises surface effects
(usually the one that gives lowest Y and highest excitation purity) for partly glossy
samples. 45/0 geometry gives rise to polarisation problems [9].

13
Colorimetry

2.6.1 Calibration and certification of the instrument ‘s accuracy

White calibration: Before Use always this instrument should be callibrated with
standard white tiles equivalent to white surface of saturated dry layer of Magnesium
sulphate, which adjusts computational parameters for any setting disturbances,
so the calculated reflectance values match with calibrated value of white tiles being
100 and the accuracy of reflactance curve is the same as the absolute reflectance
curve do it often.
Absolute certification: The instrument need better to be certified by NABL,
which verifies that the measured colour of the standard white tile is 100 or specified
values by manufacturer, within the tolerance (e.g. within 0.6 ∆E * units) from the
absolute colour of the standard white tile, in perfect agreement between instrument
and laboratories, when checked for certifiocation.
Relative certification: verifies if the measured colour of the standard white
callibrated tile is within the tolerance (e.g. 0.3 ∆E * units) from the initial colour of
the standard white tile in the same instrument, which is very very important for
reproducibility and reliability of colour data produced.

2.6.2 Measurement of overall colour difference index

Colour Difference Index (CDI) [10] indicates the combined effects of different
known individual colour difference parameters between any two samples when
dyed with varying conditions of dyeing, indicating dispersion of colour value, to
understand the combined effects of different dyeing variables by a single parame-
ter. For application of same concentration of dye between two sets of dyeing
under any varying conditions of dyeing like pH, taking only the magnitudes of
the respective ΔE, ΔC, ΔH and MI values (irrespective of their sign and
direction) may be considered to calculate CDI values using the following empirical
relationship [10].

ΔE  ΔH
Colour Difference Index ðCDIÞ ¼ (22)
ΔC  MI

Higher the CDI value dispersion of Colour values are more widely dispersed and
that variable become critical for reproducibility for such dyeing. So, Lower CDI
value below 5.0, is considered as good.

2.6.3 Use of Standrad Illuminats in reflectance spectrophotometer

The followings are the Standrad Illuminats [1–3] used in Reflectance

Spectrophotometer, providing UV -Tungsten lamp for different illuminant with
swift arrangement of Illuminnat -A to Illuminnat -D65.

• Standrad Illuminant A (CIE): CIE standard illuminant -A is defined as

equivalent light source from a tungsten filament (as radiator) when heated at
2854°K(as correlated colour temperature)

• Standard Illuminant D65 (CIE): CIE standard illuminant -D65 is defined as a

representation of natural daylight considering as equivalent light source from
a tungsten filament (as radiator) when heated at 65040 K (as correlated colour
temperature)

14
Basic Principles of Colour Measurement and Colour Matching of Textiles and Apparels
DOI: http://dx.doi.org/10.5772/intechopen.101442

Figure 10.
20 standard observer (small area of view) and 100 standard observer (large area of view).

• Standard illuminants B and C: CIE Standard illuminant -B and C are defined to

represent as simulated direct sunlight, as equivalent light source from a tungsten
filament (as radiator) when heated at 4874°K and 6774°K respectively (as
respective correlated colour temperature). But, Standard illuminants B and C are
not so much used and are being dropped because they are seriously too much
deficient in the UV region (important for fluorescent materials)

• Standard Observer: There are two angular view areas considered as standard
viewing areas called 20 standard observer (small area of view) and 100
standard observer (large area of view) as shown in Figure 10 [1–3]. As
recommended by CIE, in 1964, the larger area of view of solid samples
mounted for colour measurement on sample port of UV VIs reflectance
spectrophotometer is most widely used for evaluating colour values and for
colour matching of various types of solid samples including textiles. Ordinary
Colorimeters, on the other hand, typically use a 20 Standard Observer (as per
CIE, 1931), which has a smaller area of view and is common for general colour
measurement and colour quality control and evaluation purposes for
comparative purposes and also for printed textiles.

2.7 Computer aided colour match prediction system

Computer aided Colour Match prediction system (CACMPS) [4, 9] is the com-
bination of specific hardware and software for scientific use for measuring colour of
solid textile surface for given sample as standard for predicting the dyeing recipe or
formulation for the exact shade reproduction in a textile fabric sample to produce.
Hence, this technique is known by names e.g-computer colourant formulation,
computer recipe prediction, Instrumental colour matching system or Computer
aided Colour Match prediction system (CACMPS) using reflectance spectropho-
tometer and associated computerised sytem for storing and analysis of data with
specific software to predict colour matching of textile substrate. A colour matching
computer system consists of the following three basic modules,:

1. Colour measuring instrument: A Reflectance Spectrophotometer with specific

geometry of colour measurement, which expresses the colour in numerical
form in terms of X,Y, Z or R or K/S values with L*, a* and b*, ∆L*, ∆a* and ∆b*
and ∆E * values.

15
Colorimetry

2. Computer hardware: Usually latest PC or Laptop based Computing and data

analysis and storing system for data storing, analysing and processing for
converting and comparing etc.

3. Specific Computer aided colour match prediction software with desirable

Logic system for computer aided colour measuring /storing and analysis of
colour data to convert into relevant information in terms of calculating X,Y, Z,
R, K/S values and L*, a* and b* values or, ∆L*, ∆a* and ∆b* and ∆E * values for
textile surface colour measuring and colour match prediction by the said /
compatible specific Software to obtain desirable output required.

So, Suitable Software is crucial in recording, analysing for colour measurement

and matching and for comparing a pair of nearly matched textile dyed/coloured
samples. Samples should have the same type of fabric, same surface finish and same
shape as far as possible, for accurate measurements.
The Reflectance Spectrophotometer has small view and large view sample mount-
ing holders with small hole area or large area hole respectively to place sample to scan
its surface for colour measuring and recording in the diode type detector to use for
storing and analysis for comparison to obtain X,Y, Z or R or K/S values with L*, a* and
b*, ∆L*, ∆a* and ∆b* and ∆E * values for further use and processing for computer
aided colour match prediction from stored colour data of dyes known as database
(Fabric type wise, Dye class wise or Dye Company wise etc) as per requirement.

Standard Name = C51555ton Mode = Spectro %

cotton RFL

3.28 3.50 3.83 4.77 5.94 8.27 9.61 11.71

12.19 ‘13.08 10.72 9.42 8.67 7.68 6.53 5.36

File name = Dir cot — 3 dye combination

ID# selected = 2, 3, 4, ,5, 6, 9, 11,

Subst ID# = 1 bleach cotton

DED65’. 1.00 DEA. = 1.00, Amount t = 100

Exhaustion factors are included, Operator

ID# Colourant Amount Per cent da* db* dL* dE* Rs

ClE

Recipe Generated

Formula#1

3 OrangeSE 0.0408 0.0408 D 0.0 0.0 0.0 0.0 18.51

5 Cry SE 0.4238 0.4238 A 0.6 0.2 0.0 0.2 187.73

9 Turquoise Blue 1.6111 1.6111 F 0.5 0.3 0.3 0.7 285.44

2.0747 2.0747 491.68

Formula # 2

4 Scarlet 0.0362 0.0362 DS 0.0 0.0 0.0 0;00 16.12

5 Cry SE 0.5466 0.5466 A 0.5 0.3 0.0 0.6 194.77

9 Turquoise Blue 1.4834 1.4834 F 0.4 0.2 0.1 0.5 224.04

2.0662 2.0662 434.93

Table 1.
A case study of colour match prediction from the database of direct dye for cotton.

16
Basic Principles of Colour Measurement and Colour Matching of Textiles and Apparels
DOI: http://dx.doi.org/10.5772/intechopen.101442

After that, the associated Computer aided colour match prediction software
takes over the rest part of the work of calculations and comparison of colour data to
show the measured values and calculated colour values using stored colour database
of specific dyes for specific type of textile substrate. Table 1 shows Computer aided
colour match prediction system (CACMPS) generated dyeing recipe and its dye cost
and estimated approxmiation of Colour difference values with least metameric ratio
for cotton fabric sample to be dyed to match against given standard samples using
direct dye data base stored.
The above shown formulae of colour match prediction generated against standard
shade C5, has generated two possible recipes, and is difficult to decide which one we
should accept and proceed for bulk dyeing. From the Point of least metamerism,
formulation-1 and from the point of least cost Formula 2 are respectively found
better after 4 trial run in Computer aided colour match prediction system (CACMPS)
within DE limit to 1.00. Thus, computer predicted formulation 2 is least cost and
formulation 1 is least metameric in nature, as shown in output result generated here.

3. Some practical consideration during measurement on CCMP system

The practical aspects of data base generating match generation using a data base,
setting up proper DE or multiple colour tolerance & above all accurate spectropho-
tometer measurement depends on following factors.

3.1 Colour matching tolerance set-up and pass/fail system

It is also essential to develop mutually agreeable pass/fail system between buyer

or seller or by company itself for their shade control to match produced samples lot
with the colour values of standard shade given, which should be specified by set up
specific tolerance values of these colour difference criteria for any par of near
matched textiles. These may be more important while considering batch to batch
variation during production of shades as per match of standard samples given. As all
textile dyers and dyeing units or composite textile mills have procured this com-
puter aided colour match prediction system, this become a regular job to check
match accuracy from shift to shift or lot to lot variation always, to understand the
colour differences from standard shade given. So that the colour differences from
batch to batch variation at factory /dye house in company production department,
the shade may be corrected by revised addition of dyes, to obtain more precision
match, so that chance of rejection in export level on this ground may be eliminated
and for this, specific sets of colour tolerances values are decided and pre -set.
In practice in textile industry/ dye houses, for dyed /coloured cotton textiles, if
not otherwise mentioned/specified, the thumb rule for setting a symmetric colour
tolerances values in terms of dL*, da*, db* and dE* for effective colour matching of
cotton textiles are as follows:
Standard set of colour tolerence values: dL* = 0.7 to 1.2; da* = 0.6 to 1.0 db* = 0.6
to 1.0; dE* = 1.0 to 1.5 applicable for selected common shades and common dyes for
cotton. However, these colour tolerence limits for colour matching of dyed textiles
could be somewhat narrower in case of requirement of precission matching.
The main dependant factors responsible for lot to lot or batch to batch dyeing
production with variation of shade are: i) weighing / solubilisation/dilution error,
ii) substrate and pre treatment variation, iii) pretreatment or heat setting variation,
and iv) Variation in dyeing conditions by change of dyeing process variables or
variation in additive concentrations and 5) dye selected and its purity.

17
Colorimetry

3.2 Calibration dyeing for preparation of data base

The calibration dyeing for preparation of dyestuff data base for dyeing specific
textile fabrics with selected type and class of dyes is an essential pre requisite. After
selection of substrate and class of dyes and dye manufacturer/suppliers), to run a
computer aided colour measuring and matching system, preparation of dyestuff
data base ton store using selective class and type of dyes, the control bleached
cotton/ otherwise textile fabric sample are to be dyed with each selected dye at 5-8
different concentration levels of dyes (say, within 0.1 / 0.5 to 4%) and those
samples dyed are to be subjected to measure their reflectance values at
different wavelength and their individual values or their integrated sum of these
REflectance / tristimulus colour values are to be stored for futurev uses to form a Dye
class wise/company wise data bank or data base of all different type of dyes for
specific substrate / substance following a particular standard process of dyeing in a
separate file of the computerised processor or computer to use at every re-call.
Samanta et al. [9, 10] mentioned the cares necessary for accuracy in colour measure-
ment of textiles including nos. of folding etc. and orientation of samples and measure
of colour difference index values etc. Randall and Stutts [11] specifies how to prepare
reliable samples of calibration dyeing for creating dyestuff data base in computer
aided colour matching system as a most important step. For optimum efficacy in
computer aided colour matching system, the laboratory dyeing machine and process
must be highly controlled in terms of dyeing process variables and all these must be
standardised before callibration dyeing be carried out accurately, which is to be
assured by the lab dyers /colourist to store precision colour data/ dyestuff database
separately for company wise /substrate wise for separate class of dyes.

3.3 Checking of linearity / non-linearity for plots of K/S vs. dye conetrations in
dyestaff data base

The accuracy of computer aided colour matching system depends on the correct
dyestuff data base preparation as discussed in calibration dyeing in item 3.1 above.
The accuracy of dyestuff data base can be checked by checking linearity of K/S vs.
Dye Concentrations curve pattern for each individual dye applied on same substrate
under standardised control dyeing conditions. Sometimes, this linear relation does
not exist and then the deviation from linearity is to be eliminated, before such
dyestuff data base are stored for future use of colour matching functions. The
deviation from linearity of plot between K/S vs. dye concentration are due to
(i) inherent variation in dye uptake rate or variation in exhaustion rate of the
dye for higher percentage of dyes (ii) unknown interference of dyes with given
dye bath auxialaries (iii) variation in dyeing conditions /stirring rate (iv)
weighing/solubilisation/dilution error (v) impurities/agglomeration of few
dyestuff itself, where these said reasons causes a variation of dyeing with increase in
dye concentration [9] showing non linearity/deviation from linearity in observed.
Dye uptake.
Therefore, this linearization is to be ultimately done by statistical best fit
linearization process or elimination of one or two concentrations of dyes(where /
from which point the said linearization is originated/deviated) for particular dye or
by empirical modifications of the equation of K-M functions (K/S value). before
storing dyestuff database to be used for colour match prediction of coloured textiles
easily. For this type of special cases, the dye absorption co-efficient/difussion coef-
ficient of the dye is to be determibned and to be checked at about five to eight level
of dye concentrations to check the dyeing absorption/diffusion rate and then line-
arization can be made either eliminating few dye concentrations where dyeing rate

18
Basic Principles of Colour Measurement and Colour Matching of Textiles and Apparels
DOI: http://dx.doi.org/10.5772/intechopen.101442

is much varying. Repeat colouration is to be done to avoid variation in dyeing

process variables to get correct data. Only after linearization of plots of K/S vs.
Dye concentrations, the individual dyestuff data base may be stored in the
computerised storing and saving file as ready made database for use in
predicting recipe for colour matching formulations for specific substrate for
specific dye class within user choiced/ standard tolerances of colour differences in
terms of DE, DL, Da, Db values under standard illuminants of D65 or otherwise. If
dyestuff cost are entered and uploaded and updated regularly, the dye cost of
predicted colour matching formulations are also available along with predicted
metamerism values.

3.4 Effect of variability in measurement of colour value of textiles

Colour Matching of textiles is very much dependant on the Pigment /dye Data-
base created –dye class based and type of fibre/fabric based and dye company based
to be pre-up-loaded in spectro. To match full strength of colour, Light and dark i.e.
white and black reduction are very important.
Pigments /dyes should be thoroughly dispersed and uniformly dyed, which is
Very difficult with powder pigments, but much easier with Master batch mass
pigmentation to produce coloured textiles.
There are so many variations in measuring surface colour of textiles. A mea-
surement is never perfect. The effect of variability of colour measurement is
reduced by using multiple measurements and taking avrages at 10 points atlesat.
How many measurements should I make for averaging is a good question and Rule
of thumb is 10 times atleast for each variability parameter of dyeing for
standardising dyeing process variables. For any variable instrumental factors also,
measure each spot of colour value for 10 times to take average of it. But for sample
uniformity for data base storing data, one should repeat colour measurements at
several locations — more than 10 to 100, depending CV % of K/S values or reflec-
tance values of coloured textile surface. One can follow ASTM standard E 1345-
90 to determine how many measurements are necessary in each case.
Some more Practical Aspects of variability in colour mesurement of textile
surface [9] are:

a. Level / Un level dyeing (Usually Less than 5% CV of K/S Value is taken as

level dyeing for textiles).

b. Back ground opaqueness of the sample (No. of Folds are to be kept Constant
say usually 4 fold).

c. Variation in warp wise or weft wise sample’s vertical/horizantal orientation

may differ K/S value)

d. Variation in texture or surface roughness may vary K/S values for change in
scattering (Any chemical/ physical intervention/Treatment before dyeing
may change surface texture)

e. Variation of colour and texture in two sides of the fabric sample (K/S -surface
colour strength in one face of fabric may sometimes differ from other face
due to the said effect).

f. Any Fabric or Dyeing Defects/Stains in the fabric sample (Any defect of the
fabric may cause colour variation).

19
Colorimetry

g. Dull shade / Fluorescent colour & bright shade etc. some times behave differently.

h. Blended fabric may pose problem with change of Blend % of each component
of fibres.

The reasons of variation of colours produced in textiles during data base

preparations - are

• Improper weighing and mixing of colourants.

• Improper Cleanliness of dyeing machinery parts, like steam pipes and dye bath

• In-compatable colour mixing and variation of dyeing time and other process
variables

• Interference from regrind/ slubilization of dyes having some chnaces of

contamination.

• Shedding of fibres / Degradation of fibres or chemicals used during processing.

• Machine stoppages and inadequate steam purging in dye bath having in

adequate temperature

• Improper selection of Colourant/ Master-batch.

• Interference with processing additives - chrome pigments containing lead will

discolour if Tin stabilisers are present.

Moreover, different other cares are necessary, without which in-accurate

measurement occur for measuring of colour values of textiles –e. g.

• Accent on cleanliness: Poor housekeeping results colour contamination and

stain,

• Selecting correct Colourant and clear understanding of colour type and

properties to specific textile fibre / polymer involved. Master-batch of colour
supplier plays crucial role in this case.

• Use of pre-coloured standard materials and best checking by

replicating same colour on a same or different textiles. Cost of instrument is
usually more

• Inventory and logistics issues are there also for variation of colour and its
measurement.

Use of Pigment colouring for small quantities where Master-batch development

is easier.

3.5 Areas of application of computer colour measuring and matching system

1. Measurement of tristimulus values, reflectant at maximum absorbance wave

length or K/S measurement of transmitants.

20
Basic Principles of Colour Measurement and Colour Matching of Textiles and Apparels
DOI: http://dx.doi.org/10.5772/intechopen.101442

2. Calculation of colour difference by CIELAB equation of total colour difference

i.e. ∆E* = [(∆L*) 2 + (∆a*) 2 + (∆b*) 2]½ with plot of CIE colour difference
space diagram. The shade sorting i.e. pass/fail mechanism of quality control of
dyed shades from batch to batch or lot to lot represents colour difference
values in terms of Darkness and lightness (∆L*) Redness & Greenness (∆a and
Yellowness and Blueness (∆b*).

3. Finger Tips solution of predicting newer computer aided d colour matching

recipe /formulation with lowset cost & lowest metameric match recipe using
pre- set stored speicific dyestuff data base.

4. Batch correction or auto correction of shades by manual or computerised

corrections.

5. Extension of match Prediction by batch corrections and utilisation of dyeing

waste liquor.

6. Purity/ Quality test of incoming newer batch of dyes with the help of this
computer aided colour measuring system.

7. Determination of whiteness, yellowness and brightness indices of bleached

textile substrate using different standard scales like CIE scale, Hunter Lab
scale, ASTM-E-313 scale, Stansby scale etc.

8. Prediction of efficiency of OBA (optical brightening agents) utilising this

system by change of with or without UV light setting.

9. More accurate and Quantitative understanding and grading of colour

fastness grade for colour fading behaviour to wsah, crocking/rubbing.
Exposure to UV light etc. replacing conventional grey scale rating.

4. Surface appearence measurement in terms of whiteness, yellowness

and brightness indices

Whiteness is assesment of freedom from any colour and contamination/stain /

soil and as such it is taken as an indicator of quality for a bleached textile fabric
prepared for dyeing. Objective measurement and meaningful numerical expression
whiteness index as per CIE and Hunter lab scale are widely used. It represents
whiteness index (WI) in terms of colorimetric values for the specimen and the
chromaticity coordinates of the illuminant:

WIðCIE scaleÞ ¼ Y þ 800ðxn xÞ ¼ 1700 yn y (23)

 
pffiffiffiffi pffiffiffiffi
WIðHunter Lab‐ScaleÞ ¼ L ∗ 3b ∗ ¼ 10 Y ½21ðY Z%ފ= Y (24)

where x, y and Y are the colorimetric values for the sample under illuminant
D65, and xn and yn are the chromaticity coordinates of the light source/illuminant
used. A value for WI of 100 represents a perfect reflecting white diffuser,
equivalent to surface of saturated paste of Magnesium sulphate.
X, Y and Z are the CIE tri-stimulus values of the sample and L* is the lightness/
darkness indicator, b* is the blueness/yellowness indicator.

21
Colorimetry

Similrly, yellowness indices [12] as per ASTM-E313/1973 can be expressed as

follows:

0:8477

Yellowness Index ðYIÞðASTM‐E313=1973Þ ¼ 100 ½1–ðB=Gފ ¼ 100 1
Y
(25)

Where, X, Y and Z are the CIE tri-stimulus values of the sample, L* is the
lightness/darkness indicator, b* is the blueness/yellowness indicator and
B = Z/1.181 = 0.847 Z, G = Y = L2 /100.
Brightness Index (BI) as per ISO-2469/2470-1977method [13] can be calculated
by following formula:

Brightness index ¼

Reflectance Value of the Sample at 457 nm

 100
Reflectance value of Standard white diffuser ðwhite tilesÞat 457 nm
(26)

Treatment with fluorescent brightening agents can lead to reflectance values of

up to 150. Although the pattern appears to become whiter, the change in appear-
ance is due to a change in chroma towards blue, and this fact is expressed in
quantitative form as the ‘tint factor’. Allied to the appearance of the uncoloured
fabric is the yellowness, which suggests yellowing by chemical treatment or by heat
scorching or degradation by light or by gases. Thus along with colour parameter the
said other surface appearance properties are also very very important too in defin-
ing the quality of the surface appearance of any textiles.

5. Importance of colour measurements and matching in

garment industry

Colour is one of the important element of a design. Colour with aesthetics /

texture of anty textile fabrics / garments are as important as its physical and
functional property criteria. Matching of colours, especially in specific textiles made
from specific or different fibres and their blends is very very crucial in many
applications. The task of communicating and measuring and matching of colour
becomes more difficult when colours need to be exactly matched with a given
standard supplied for different textiles. More and more precision colour matching is
required in specialised textile products like defence dress materials, school uniform
etc. and also for matching suits for consumer textiles and livestyle products for
matched furnishings, bed linen and auto Interiors etc.
This Computer aided reflactance spectrophotometer is an impoartant tools/
intrument for quality up grdation of textiles and garments by maesuring surface
colour strength and colour dierences values as per CIE equations/ formulae. Some
Other Application of computer aided colour measuring cum matching System used
in textiles or apparel industry’s Dye House:

1. For quality control of dyed textiles including pass/fail decision of batch to

batch checking.

2. For Evaluation of Quality of dyes supplied.

22
Basic Principles of Colour Measurement and Colour Matching of Textiles and Apparels
DOI: http://dx.doi.org/10.5772/intechopen.101442

3. Effect of dyeing additives by measuring colour yield.

4. Efficiency of optical brighteners by UV analysis.

5. Soil removal efficiency of surfactants by measuring Reflectance value.

6. Measurement of whiteness / yellowness / brightness index etc. of undyed and

bleached samples besides dyed samples.

6. Concluding remarks

Computer Aided Colour Measuring and Match Prediction System (CACMPS),

now a days, become an essential tools for each textile dye houses to match colours
or shade as per panton shade nos. or as per given samples, to reduce export rejection
for colours. Moreover, to judge colour fastness grading more accurately from mea-
surement of colour difference values after corresponding fading by wash or light or
rubbing etc., than subjective/comparative judging by grey scale rating purpose is
more scientific and advantegios. Quality control activity and batch to batch pass /
fail checking of shades developed from shift to shift needs to be implemented in all
dye houses for quality assurance on colour matching which is an integral demand of
today’s apparel and fashion industry. Hence learning of colorimetric principles of
UV VIS reflectance spectrophotometer and proper utilisation of this instrument
carefully for deriving all round benefits out of it, for surface colour measuring and
matching of textiles for customer satisfaction is also helps in brand building by
quality assurance on colour matching of textiles.

Acknowledgements

The author is thankful to the Principal RBGC, Kolkata for her encouragement
and support.

Author details

Pubalina Samanta
Department of Fashion and Apparel Design, Rani Birla Girls’ College, Kolkata,
West Bengal, India

*Address all correspondence to: [email protected]

© 2022 The Author(s). Licensee IntechOpen. This chapter is distributed under the terms
of the Creative Commons Attribution License (http://creativecommons.org/licenses/
by/3.0), which permits unrestricted use, distribution, and reproduction in any medium,
provided the original work is properly cited.

23
Colorimetry

References

[1] Shah HS, Gandhi RS. Instrumental [10] Samanta AK, Agarwal P, Singhee D,
Colour Measurements & Dutta S. Application of single and
ComputerAided Colour Matching mixtures of red sandalwood and other
for Textiles. Amhedabad, India: natural dyes for dyeing of jute fabric:
Mahajan Book Distributers; 1990. Studies on colour parameters / colour
pp. 76–116 fastness and compatibility. Journal of
the Textile Institute. 2009;100(7):
[2] Gangakhedkar NS. Part II : Colour 565-587
measurement and its applications. In:
Gularajani ML, editor. Colour [11] Randall D, Stutts T. Optimizing
Measurement: Principles, Advances and calibration dyeings for computer color
Industrial Applications. Manchester, matching. American Dyestuff Reporter.
UK: Woodhead Publishing, India and 1988;28:44-46
Textile Institute, Series in Textiles;
2010. pp. 219–252 [12] ASTM-E-313-67/E-313-73 (Re-
approved-1979). Determination of
[3] McLaren K. The Colour Science of yellowness. In: Annual Book of ASTM
Dyes and Pigments. 2nd ed. Bristol: Standards E 12.02. Philadelphia,
Adam Hilger; 1986. pp. 50–87 Pennsylvania, PA: American Society for
Testing Materials; 1974. p. 1
[4] Pubalina S. Fundementals and
applications of of Computer aided [13] ISO-2470-1977 (E) and ISO-2469.
Colour Match Prediction (CCMP) Determination of Brightness.
System. Latest Trends in Textile and Switzerland: International Organization
Fashion Design Journal. 2018;2(5):1-10 for Standardization (ISO); 1977. pp. 1–3

[5] Ingamells W. Colour for Textiles-

A user’s handbook. Bradford, UK:
Society of Dyers and Colourists; 1993.
pp. 138–157

[6] Samanta AK. On-line colour control

(for textile dyeing). Indian Textile
Journal. 1992;105:70

[7] Samanta AK. Review on Colour

Control and Matching. Indian Textile
Journal. 1995;108:50

[8] Samanta AK. A review and case

study of computer application in jute
or textile mills’ dye house and
computerized colour matching. Textile
Trend. 1993;36:37

[9] Samanta AK, Das D. Studies on

Quantitative colour measurement of
direct dyed Jute Fabric in relation to
computerized colour matching. Journal
of Institution of Engineers-Textile
Engineering. 1992;73:53

24