product data Structural Concrete Repairs

SEALBOND 215-B
CONCRETE EPOXY ADHESIVE
Product Description Technical / Performance Data

SEALBOND CONCRETE EPOXY ADHESIVE (215- Viscosity 4,900 cps

B) is a two component adhesive system specially Minimum shrinkage at
formulated for structural concrete application and Shrinkage
curing action
bonding of old to new concrete. It has a low to Compressive Strength Min 8,000 -10,000 at 7 days
medium viscosity. When compounded, the admixture ASTM C109-95/ D695 Max 12,000 -14,000 at 7 days
produces a strong bond with minimum shrinkage and Tensile Strength
4,000 – 7,000 psi at 7 days
flexibility properties. It contains a special polymeric (ASTM D638)
curing agent that provides the film with a high degree Flexural Strength
5,000 – 8,000 psi at 7 days
of toughness, adhesion and chemical corrosion (ASTM D790)
resistance. Highly resistant to most
Resistance to
acids, alkalis, salts,
Application Areas Chemicals
alcohol & solvents.
 Bonding new to old concrete Solid by volume 100%
 Repair of cracked concrete structure including
earthquake damages Procedure & Guidelines
 Sealing concrete pavement and structure
SURFACE PREPARATION
against intrusion of water
 Dowelling GENERAL
 Bonding non-slip aggregates on concrete All surfaces must be thoroughly cleaned to remove
surfaces dirt, grease, mill scale, loose rust, chalk, and any
 Securing overlays on concrete surfaces other contaminants that can reduce adhesion.
 General purpose adhesive
MIXING
Processing Data Mix 2 Parts by volume of Resin Base (Part A) to 1
Part by Volume Hardener (Part B). Use of a power
Mix Ratio mixer is recommended to attain complete
2 Part A: 1 Part B
(by volume) homogenizing of a compound. Mix only enough
Gel Time at 25 ºC 20-30 minutes quantities that can be used within the pot-life of the
Initial Cure at 25 ºC 60-120 minutes mixture.
24 hours, 72 hours before
Full Cured at 25 ºC
applying pressure APPLICATION
Pot Life at 25 ºC 30-40 minutes Apply SEALBOND EPOXY 215-B using roller or
Shelf Life
Min 2 years at room brush on the surface at the rate of 6 to 8 sq. meters
temperature per gallon depending on the thickness of deposit or
porosity of the substrate.
Pour fresh concrete while SEALBOND EPOXY 215-B
is still wet or tacky. Use brush with stiff bristles to fill
up concrete voids and concrete crevices with Epoxy
industrial Adhesive.

…………..………………………...…………………………………………… Structural Concrete Repairs

AUGUST 2020
This technical data contained herein is true and accurate to the best of our knowledge on the date of publication and is subject to change without prior notice. User must contact Sealbond Chemical Industries Inc. to
verify correctness before specifying or ordering. We assume no responsibility for coverage, performance or injuries resulting from use. Liability, if any, is limited replacement of products. Sealbond Hi-Perfomance is
registered trademark of Sealbond Chemical Industries Inc.
www.sealbondchemicals.com
 product data Structural Concrete Repairs

SEALBOND 215-B
Clean up. All tools and equipment must be cleaned Additional Information - Disclaimer
immediately after application. Use Sealbond Epoxy
The information and in particular, recommendations relating to the application and
Reducer to remove excess resin and hardener. end-use of Sealbond products, are given in good faith based on Sealbond’s best
knowledge and specialty on construction chemical formulations. Products are
properly stored and handled in accordance with Sealbond’s endorsements. Hence,
Theoretical Coverage subject to the care and method of application, deviations (from published values) in
performance may occur. In practice, to different materials used, as well as varying
SEALBOND 215-B covers approximately 6m2 to 8m2 working conditions and environments beyond our control Sealbond Chemical
Industries Inc. strictly recommend carrying out intensive trials to test the suitability
per gallon depending on the thickness of deposit or of the product with regards to the required processes and applications. Therefore,
porosity of the substrate any liability for such recommendations or any oral/verbal advice is expressly
excluded unless we have acted wilfully or by gross negligence. Sealbond
Chemicals Industries Inc. is not liable for installation or faulty installation. It is
Health & Safety always the responsibility of the installer/applicator/purchaser to guarantee and
certify the installation of materials.
Avoid contact with eyes and skin and avoid breathing All orders are accepted subject to our current terms of sale and delivery. Users
its vapor. This product may cause severe skin must always refer to the most recent issue of the Product Data Sheet for the
product awareness, copies of which will be supplied on request and is free of
irritation after prolonged or repeated exposure. Keep charge.
containers tightly closed and store in a cool dry place.
Product is for Professional use only.

Storage / Packaging

SEALBOND 215-B is available in 3.8kg per gallon kit.

This product must be stored dry, protected from sun

and rain.

Product Limitations
Product can withstand heavy load but cannot
withstand excessive abrasion.

A-2 Araneta St. Cor. Gen. Natividad St.

Bgy. Ibayo, Tipas Taguig City, Philippines

PH: (632) 881-8813 ● (632) 883-1477 ● (632) 845-0205

● (632) 843-4498 ● (632) 845-0137
www.sealbondchemicals.com

…………..………………………...…………………………………………… Structural Concrete Repairs

AUGUST 2020
This technical data contained herein is true and accurate to the best of our knowledge on the date of publication and is subject to change without prior notice. User must contact Sealbond Chemical Industries Inc. to
verify correctness before specifying or ordering. We assume no responsibility for coverage, performance or injuries resulting from use. Liability, if any, is limited replacement of products. Sealbond Hi-Perfomance is
registered trademark of Sealbond Chemical Industries Inc.
www.sealbondchemicals.com