TILE BOND ANTI-SLIP

SCIENTIFIC WATERPROOFING SOLUTIONS

High-performance, highly polymer-modified, flexible cementitious tile adhesive with

extended open time for vitrified, ceramic, natural stone, and marble glass mosaics It
is classified as C2TE according to EN 12004 and Type 3T according to IS 15477:2019.
Product Description
This is a ready-made polymer modified adhesive with a high-performance cement
base (C), improved slip resistance (T), and extended open time (E). It is suitable for
fixing vitrified tiles, glass mosaics, and natural stone.
Application Area:
Product USP Materials to be fixed: all types of ceramic tiles, vitrified tiles, terracotta, bricks, large
format tiles, ceramic and glass mosaics, marble, and natural
Highly stones.
polymer-modified Substrates: cement-based screeds, cement-based plasters, concrete
adhesive surfaces and brick walls and screeds, cement-based
waterproofing products, cement-based self-leveling products,
existing tiles and stones, water-retaining bodies, etc.
Area of use: Interior and exterior walls and floors, domestic applications,
Good chemical commercial applications, facades, dry and wet areas like water
adhesion strength tanks, swimming pools, saunas and spas, fountains,
balconies, terraces and podium decks.
Product Attributes
For balconies Pot Life @ 30°C: Approx. 75 MIN
and terraces Coverage: 50-55 sqft (with 6mm x 6mm notch trowel)
25-27 sqft (with 12mm x 12mm notch trowel)
Adhesive Thickness: Up to 12 mm
Sustains Slip Resistance: ≤ 0.5 mm
heat aging
Technical Data
PROPERTIES SPECIFICATION
Base Especially active additives mixed in
No vertical slip cement and silica/ quartz sand mortar.
Aspect Grey Adhesive: Grey Powder
White Adhesive: White powder
Bulk Density (gm/cc) 1.25 – 1.4 kg/lt
Extended
Open time Mixed Density (w/p=0.24) 1.5 – 1.75 kg/lt.

Open time @ 30°C ≥ 30 min

Application up to Adjustment time @ 30°C ≥ 20 min
12 mm thickness
Temperature of Substrate,
Air & Materials during From +5° C to +35° C
Application
Comes with Dry condition: ≥1.5 N/mm²
Grey and Tensile adhesion strength
White Colour (After 28 Days) After water immersion: ≥1.0 N/mm²
Dry condition: ≥1.5N/mm²
Shear adhesion strength Heat ageing condition: ≥1.0 N/mm²
No shrinkage and
water resistance Wet condition: ≥1.0 N/mm²
Applied product ready for use:
Curing Time Floor grouting - light foot Traffic after 24- 36hour,
Wall grouting after 24 hours
Very low VOC Light Traffic: after 48 hours
Ready to use
Heavy traffic: after 72 hours
 TILE BOND ANTI-SLIP
SCIENTIFIC WATERPROOFING SOLUTIONS

DIRECTION FOR USE

Surface preparation
Prior to application, make sure the substrate is cement laitance-free, clean,
and free from dirt, oil, grease, or other contaminants and loose or friable
particles that may affect the adhesion strength. All surfaces must be
dimensionally stable, level, cured, undamaged, compact, rigid, and dry.
Dampening shall be done with water over dry and dusty surfaces. For more
absorbent surfaces, apply a coat of HS Latex Shield 2K, and for wet areas, apply two coats of
Wall Shield 2K before two days. The substrate must be perfectly flat, sound, free from parts
that are easily removed, non-deformable, and correctly aged or cured. Undulation can be
leveled or filled with a layer of HS Tile Bond Anti-Slip in a maximum thickness of 5 mm,
applied at least 24 hours before.
Packs Areas of weak or honey-combed base surfaces should be sufficiently flat to permit the
specified thickness. During application, there should not be any standing water.
Supplied in 20 kg
& 40 kg bags.

Mixing
HS TILE BOND ANTI-SLIP is thoroughly mixed with potable water (always
pour water into powder and not the reverse) until a lump-free mortar mix
is obtained (at least 3 minutes of mixing is necessary).
A 20-kg bag of powder requires 4.6 to 5.6 liters of water. The adhesive is
immediately ready for use. Always mix the required quantity, which can
be consumed within the pot life.
Shelf Life Let the mixture air dry for 5 minutes before use. No further water should
12 months from the date be added.
of manufacturing in
unopened condition
Application Method
• To obtain a 3mm thickness, use a 6mm x 6mm notch trowel. The amount of product
should be enough to ensure complete wetting of the tile. Tiling has to be carried out on
fresh adhesive.
• applying an optimum pressure to ensure contact with the adhesive with the tile to form a
perfect bond.
• Avoid wetting the adhesive already applied with water.
Storage
• To lay tiles sized larger than 300mm x 300mm, use the double-spreading (back buttering)
Store in cool and dry place, free thin-bed consistency or single-spreading flow-bed consistency technique.
from direct sunlight and frost.
Approx. temp range (+) 5 °C to Of adhesive application is always recommended.
40°C. In tropical climate the • If the substrate is very porous and the temperature is high and/or the relative humidity is
product must be stored in an air low, it is advisable to dampen the surface.
conditioned environment.
• Do not leave any standing water.

Health & Safety precaution

Wear hand gloves, safety shoes and safety goggles while using and handling the product. In
case eyes or mouth are affected wash with plenty of clean water and seek medical treatment
immediately. Before use, refer to the Material Safety Data Sheet (MSDS).

Version No: BPP1/04/2024. Please note that this data sheet supersedes all previous versions.

BERGER PAINTS INDIA LIMITED

Berger House, 129 Park Street, Kolkata 700 017 | CONSUMER RELATIONS MANAGER Ph: 1800-103-6030
Fax: 91-33-2249-9729/9009 | SMS BERGER to 56767 | Email: [email protected] | www.bergerpaints.com