Scribd
Upload
92 views4 pages

X-64m2 Add JUN Rev101

Uploaded by

chassisd
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
92 views4 pages

X-64m2 Add JUN Rev101

Uploaded by

chassisd
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

Product Data Sheet

Addendum

X-64m2 Series
SATA III - 6 Gbit/s
MLC Flash

B U: Fl a sh Pr od u ct s
Date : Janu ar y 4 , 2 0 17
Re vi si o n: 1 .0 1
Fi le : X - 6 4m 2_A dd _J U N_Re v 1 0 1. doc x
X-64m Series - Commercial M.2 Solid State Drive
32 GBytes, 50 GBytes, and 100 GBytes
1 Ordering Information
The following table lists the part number associated with the changes identified in this document.

Table 1: Available Part Number


Density Form Factor Part Number
32 GBytes 2242 SFSA032GM3AA1TO-C-LB-21A-JUN
50 GBytes 2242 SFSA050GM3AA2TO-C-LB-21A-JUN
100 GBytes 2280 SFSA100GM3AA4TO-C-LB-62A-JUN
100 GBytes 2280 SFSA100GM3AA4TO-C-LB-62C-JUN*
*The "C" in "62C" indicates PFAIL support.

2 Product Changes
The Juniper M.2 2242 and 2280 Solid State Drives (SSDs) are identical to the Swissbit® standard X-60m2 devices
with the exceptions identified in the following sections.

2.1 Hardware Changes


The Juniper SSDs are built with the generation 3 printed circuit board (PCB) and 4-plane NAND.

2.2 Performance Specifications


The X-64m2 read/write sequential and random I/O performance benchmarks are detailed below in Table 2.

Table 2: Read/Write Performance1


Sequential Read Sequential Write Random Read Random Write
Drive Capacity
(MBPS) (MBPS) (IOPs) (IOPs)
32 GBytes 315 85 26,500 20,500
50 GBytes 520 170 51,000 41,500
100 GBytes 520 315 69,500 61,500

2.3 Drive Geometry Changes


The drives are set to report industry standard LBA setting per the IDEMA standard (LBA1-03) as shown below.

Table 3: Drive Geometry


Total LBA User Addressable Bytes
Drive Capacity User Capacity2
Decimal (Unformatted)
32 GBytes 32 GBytes 62,533,296 32,017,047,552
64 GBytes 50 GBytes 97,696,368 50,020,540,416
128 GBytes 100 GBytes 195,371,568 100,030,242,816

1
The values are measured using CDM across the full drive density. Performance depends on flash type and number, file/cluster size, and
burst speed.
2
1 GByte = 109 bytes
Swissbit AG Revision: 1.01
Industriestrasse 4
CH-9552 Bronschhofen www.swissbit.com X-64m2_Add_JUN_Rev101.docx
Switzerland [email protected] Page 2 of 4
2.4 Endurance
Because the over-provisioning affects the write amplification factor, the endurance numbers are different for
these devices. See the following table for the endurance represented as both TeraBytes Written (TBW) and full
Drive Writes Per Day (DWPD) for three different application scenarios.

Table 4: Endurance3
Drive Client Enterprise Embedded
Capacity TBW DWPD TBW DWPD TBW DWPD
32 GBytes 49.08 1.43 10.22 0.30 14.42 0.42
50 GBytes 96.37 48.83 83.71
1.80 0.91 1.57
100 GBytes 192.74 97.66 167.41

2.5 Identify Device


Words 100-103 of the Identify Device return the user-addressable sectors listed in Table 3.

2.6 S.M.A.R.T. Data


Self-Monitoring, Analysis, and Reporting (S.M.A.R.T.) data for the Total Flash LBAs Written attributes (EBh and
EDh) report values in increments of 64 KBytes instead of 32 KBytes.

2.7 PFAIL Support


Model number SFSA100GM3AA4TO-C-LB-62C-JUN offers additional power loss protection (PFAIL). These drives contain
an array of holdup capacitors designed to supply voltage to the controller long enough for data hardening to
complete. If the voltage drops below a specified threshold, the PFAIL signal is asserted, notifying the controller
of the voltage loss. The controller then begins the process of hardening data and switches the power supply to
the power manager from the host to the capacitor array. This allows the controller to complete any writes that
were in progress at the time of power loss.

3
Client and Enterprise workloads follow the JEDEC JESD219 standard; the Embedded workload creates a 4 KByte file and appends it.
Enterprise workload values are measured based on 168 hours of runtime.

Swissbit AG Revision: 1.01


Industriestrasse 4
CH-9552 Bronschhofen www.swissbit.com X-64m2_Add_JUN_Rev101.docx
Switzerland [email protected] Page 3 of 4
3 Revision History
Table 5: Document Revision History
Date Revision Type Revision Details
23-Sep-2016 0.01 Initial draft.
26-Sep-2016 1.00 Initial release.
4-Jan-2017 1.01 Added 100 GByte offering.

Disclaimer:
No part of this document may be copied or reproduced in any form or by any means, or transferred to any third
party, without the prior written consent of an authorized representative of Swissbit AG (“SWISSBIT”). The
information in this document is subject to change without notice. SWISSBIT assumes no responsibility for any
errors or omissions that may appear in this document, and disclaims responsibility for any consequences
resulting from the use of the information set forth herein. SWISSBIT makes no commitments to update or to keep
current information contained in this document. The products listed in this document are not suitable for use in
applications such as, but not limited to, aircraft control systems, aerospace equipment, submarine cables,
nuclear reactor control systems and life support systems. Moreover, SWISSBIT does not recommend or approve
the use of any of its products in life support devices or systems or in any application where failure could result
in injury or death. If a customer wishes to use SWISSBIT products in applications not intended by SWISSBIT, said
customer must contact an authorized SWISSBIT representative to determine SWISSBIT willingness to support a
given application. The information set forth in this document does not convey any license under the copyrights,
patent rights, trademarks or other intellectual property rights claimed and owned by SWISSBIT. The information
set forth in this document is considered to be “Proprietary” and “Confidential” property owned by SWISSBIT.

ALL PRODUCTS SOLD BY SWISSBIT ARE COVERED BY THE PROVISIONS APPEARING IN SWISSBIT’S TERMS AND CONDITIONS OF
SALE ONLY, INCLUDING THE LIMITATIONS OF LIABILITY, WARRANTY AND INFRINGEMENT PROVISIONS. SWISSBIT MAKES NO
WARRANTIES OF ANY KIND, EXPRESS, STATUTORY, IMPLIED OR OTHERWISE, REGARDING INFORMATION SET FORTH HEREIN
OR REGARDING THE FREEDOM OF THE DESCRIBED PRODUCTS FROM INTELLECTUAL PROPERTY INFRINGEMENT, AND
EXPRESSLY DISCLAIMS ANY SUCH WARRANTIES INCLUDING WITHOUT LIMITATION ANY EXPRESS, STATUTORY OR IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

©2017 SWISSBIT AG All rights reserved.

Swissbit AG Revision: 1.01


Industriestrasse 4
CH-9552 Bronschhofen www.swissbit.com X-64m2_Add_JUN_Rev101.docx
Switzerland [email protected] Page 4 of 4

You might also like