Scribd
Upload
48 views7 pages

Archive Revision 6 Technical Bulletin en USpdf

Uploaded by

Nafis Tyagi
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
48 views7 pages

Archive Revision 6 Technical Bulletin en USpdf

Uploaded by

Nafis Tyagi
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 7

Global Fire Detection Products Technical Support

May 22, 2020

TSW Revision 6.01


Functional Changes SOFTWARE LICENSE IS REQUIRED FOR PHASE 6 TSW
and Enhancements: SOFTWARE.

• TSW now uses Software Licenses instead of dongles


and feature codes
• Added new report type for TrueAlert Self-Test Results
• Increased maximum user point capacity to 250K
• TSW now supports running with UAC ON or OFF
(Admin/Elevated privileges are still required)

Enhancement • 996404 TSW Uninstall should add prompt to optionally


Request remove ES Net Diag service.

Repaired Defects: Fixed Defects


• Before installing on Windows 7 64 bit systems,
Microsoft Windows Update KB3033929 must be
installed in order for the Simplex 4120 Network Card
to install/function properly.

• 988659 Foreign/Alternate Labels on a TSW doesn't stay


• 988781 TSW Unexpected Crash on 4.02.04
• 989443 2-Stage CANPUL Stage 2 does not show in History
Log if the Stage 1 was not acked first
• 989088 Job is not tagged for save after updating
UseAltLabels setting from TSWConfigurator.exe.config
• 989534 TSW Remote Client 3.01.02 will not Open on a
Customer Supplied Machine
• 989474 Remote client does not show ES Net network
topology
• 1009122 TSW terminates when DynDB.enc is corrupted
• 1013202 Skip midnight dongle/license refresh to avoid crash
• 1008928 TSW server does not raise trouble with supervised
client tries to connect
• 1013474 New Windows updates causes trouble on TSW
systems with RAID
• 1013591 Configurator: ESNET Type network build error on
4120 Network. #Error P10020
Other Changes: TSW now comes bundled with the TSW File Transfer application
that can be used to update the ES Net NIC Card firmware.
Reserved Pseudo ES Net card’s pseudos are created dynamically in the User Pseudos
Points: range when the card is added. They are populated at the next
available location in the User Pseudos range large enough to
contain contiguously these pseudos.

In the following list, “Pxxx” represents a number that gets


dynamically assigned as cards are added to the job

Pseudo Label Extra information


PXXX EXTRA SLAVE CARD
PXXX+1 LOOP n NETWORK Reserved for future
DOWNLOAD ENABLE use.
PXXX+2 ES NET Card n
MISSING/FAILED
PXXX+3 ES NET Card n WRONG
CARD
PXXX+4 ES NET Card n DUPLICATE
CARD
PXXX+5 ES NET Card n
INCOMPATIBLE SLAVE REV
PXXX+6 ES NET Card n CARD
CONFIG IN PROGRESS
PXXX+7 ES NET Card n MEDIA
MODULE 1 MISMATCH
PXXX+8 ES NET Card n MEDIA
MODULE 2 MISMATCH
PXXX+9 ES NET Card n MEDIA
MODULE 1 FAILURE
PXXX+10 ES NET Card n MEDIA
MODULE 2 FAILURE
PXXX+11 ES NET Card n VERSION
MISMATCH
PXXX+12 ES NET Card n FIRE
NETWORK LINK DOWN
PXXX+13 ES NET Card n MIS-WIRING
PXXX+14 ES NET Card n DEGRADED
STYLE 7
PXXX+15 ES NET Card n DUPLICATE
NODE
PXXX+16 ES NET Card n NON_SYNC Reserved for future
NODE IN NETWORK use.
PXXX+17 ES NET Card n FIRE
NETWORK COMMS
PXXX+18 ES NET Card n EXTRA NODE
PXXX+19 ES NET Card n PORT A LINK
DOWN
PXXX+20 ES NET Card n PORT B LINK
DOWN
PXXX+21 ES NET Card n PORT C LINK
DOWN
PXXX+22 ES NET Card n PORT D LINK
DOWN
PXXX+23 ES NET Card n PORT E LINK
DOWN
PXXX+24 ES NET Card n PORT F LINK
DOWN
PXXX+25 ES NET Card n PORT G LINK
DOWN
PXXX+26 ES NET Card n PORT H LINK
DOWN
PXXX+27 ES NET Card n PORT A
GROUND FAULT
PXXX+28 ES NET Card n PORT C
GROUND FAULT
PXXX+29 ES NET Card n PORT E
GROUND FAULT
PXXX+30 ES NET Card n PORT G
GROUND FAULT
Installation IMPORTANT!
Procedure for • Use “Customer PC” download
TSW PC: • Click Start, Settings, Control Panel, Add/Remove Programs to
remove existing TSW programmer THEN REBOOT THE
COMPUTER before installing new TSW software.
• Run the install and follow the instructions carefully, being sure to
reboot the PC when prompted.
o if necessary, install will prompt you to install Microsoft
.NET Framework 4.
• Requires New Network Programmer version 2.04 or newer
• Requires a Software License to work. Security Service
software version 2.01 is needed to use the Software License
for pre-6.01 TSW, no dongle necessary.
• TSW Runtime (Client and Server) and configurator now
supported for Windows 7 and Windows 10 only.
• PCI network card requires PCI Driver version 4.01.01.00 or
newer to run on Windows 7 platform. This version is
installed by the TSW software install beginning with version
1.01.04.F1 TSW.
Installation • A complete TSW software installation of version 6.01 or newer
Procedure for must have been done before using this utility.
Service Laptop PC • TSW version 5 and up requires .NET Framework version 4.6.1. If
GCCREV utility: using a pre-Windows 7 pc you WILL need to do the full install of
the version 6 TSW software, which installs the .NET Framework
automatically, or get the software from Microsoft to install.
• Use “Quick-Change Utility” download
• Download the desired version of the TSWREV software to the
PC, then double click on the file to install the new version
software to the GCCREV’s folder.
• To install as the active programmer version click Start,
Programs, Simplex, TrueSite, TSW, GCC Revs, Change to 6.01.
• Note: All existing versions of TSWREV’s for TSW have been
redone to accommodate major differences between phase 1 and
phase 2 TSW. Redownload existing TSWREV versions before
changing between phase 1 and phase 2 versions for the first
time.
FEATURE CHART

Revision 6.01 and later, all Features purchased through the


Software License.

Individually Protected Features activated by


Purchased ordering 4190-5065
Feature 3. 3. 4. 4. 5.
version 0 0 0 0 0
2 4 1 2 4

DACR (ALL X
versions)
Remote Client X
Up to 20 for
4120 Network
Up to 60 for
ES Net (Rev
5.04 and no
4120 network
configured)
Control X
Functions
(Version
3.01.02)(only if
using 741-834
dongle)
3rd Party X
Remote Client
(Version 3.02)
TSW Mobile X
Client App
(version 3.03)
ES Net X
Supplemental
Traffic
(Version 5.04)
Save/Restore X
Test Mode
Group
Export to XML X
Multiple X
Banners
(screen:x
command line
argument)
Jump to X
Terminal
Mode from
Common
Trouble
TSW Mobile X
Client App
(version 3.03)
Point Capacity X
increase to
100,000 points
Modernize X
TSW Banner
Buttons
Command X
Link
execution
Prompt
Automatic X
Backup of
Historical Log
Automatic X
Refresh of
Historical Log
Point Status & X
Control show
relays
separate from
signals
View/Enter X
Operator
Notes from
Active List
Windows 10 X
support
Custom Test X
Mode Groups
Auto— X
Restoral of
runtime grid
column sizes
Enable/Disabl X
e of Individual
Email Ports
Ability to turn X
off Sound at
unsupervised
clients and
clients
without
control
capability
Graphics X
option for
Travel to
Coverage
Zone or
Primary
screen for a
point
Configurator X
option to
control point
indexes for
public TSW
points.
Multi-Loop for X
ES Net
Secondary X
Server Option
for Clients

You might also like