SPC56XXMB

SPC56xx microcontroller family evaluation motherboard

Data brief − production data

Features
■ SPC56xx modular evaluation system
■ On/off power switch with LED indicators
■ Board power supply: 12 VDC external supply
voltage
■ Onboard STMicroelectronics® L9758 voltage
regulator with three simultaneous output at
1.2 V, 3.3 V and 5 V
■ Possibility to configure onboard peripherals to
operate at 5 V or 3.3 V logic levels, depending
on target ■ Specifications:
■ Two CAN channels with jumper enable – Board size 5.5” x 9.0”
– One CAN channel with High-Speed – 12 VDC Center Positive power supply with
transceiver and DB9 male connector 2.5/5.5 mm barrel connector
– One CAN channel with Low-Speed Fault
Tolerant and High-Speed transceiver Description
(selectable with jumpers) and DB9 male
connector The SPC56XXMB motherboard is an evaluation
system supporting STMicroelectronics'
■ Two LIN channels with jumper enable
SPC560xx microprocessors.
– One channel with transceiver and pin
header connector populated The complete system consists of an
– One channel with footprints only SPC56XXMB motherboard and an
SPC56xxxADPT mini module (not included)
■ One SCI channel with jumper enables, which plugs into the motherboard.
transceiver and DB9 female connector
Different mini modules are available for
■ Two FlexRay channels with jumper enables
evaluating the different devices in the SPC560xx
– One channel with transceiver and DB9 family of microprocessors.
male connector
– One channel with footprint only The evaluation system (motherboard and mini
module) allows full access to the CPU, all of the
■ Four user push buttons with jumper enable and CPU's I/O signals, and the motherboard
polarity selection peripherals (such as CAN, SCI, LIN).
■ Four user LED’s with jumper enables
■ One potentiometer for analog voltage input
■ Pin array for accessing all I/O signals
■ Expansion connectors for accessing all I/O
signals
■ Prototyping area with 0.1” spacing and SOIC
footprint

September 2012 Doc ID 023625 Rev 2 1/4

This is information on a product in full production. For further information contact your local STMicroelectronics sales www.st.com 1
office.
Order codes SPC56XXMB

1 Order codes

Table 1. Device summary

Part numbers Device supported

SPC56XXMB Mother board for SPC56xx family of devices

2/4 Doc ID 023625 Rev 2

SPC56XXMB Revision history

2 Revision history

Table 2. Document revision history

Date Revision Changes

Initial release.
11-Sep-2012 1 SPC560XXMB was previously in document DM00044221
(DocID 022591) revision 1.
18-Sep-2013 2 Updated disclaimer.

Doc ID 023625 Rev 2 3/4

 SPC56XXMB

Please Read Carefully:

Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.

UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
ST PRODUCTS ARE NOT DESIGNED OR AUTHORIZED FOR USE IN: (A) SAFETY CRITICAL APPLICATIONS SUCH AS LIFE
SUPPORTING, ACTIVE IMPLANTED DEVICES OR SYSTEMS WITH PRODUCT FUNCTIONAL SAFETY REQUIREMENTS; (B)
AERONAUTIC APPLICATIONS; (C) AUTOMOTIVE APPLICATIONS OR ENVIRONMENTS, AND/OR (D) AEROSPACE APPLICATIONS
OR ENVIRONMENTS. WHERE ST PRODUCTS ARE NOT DESIGNED FOR SUCH USE, THE PURCHASER SHALL USE PRODUCTS AT
PURCHASER’S SOLE RISK, EVEN IF ST HAS BEEN INFORMED IN WRITING OF SUCH USAGE, UNLESS A PRODUCT IS
EXPRESSLY DESIGNATED BY ST AS BEING INTENDED FOR “AUTOMOTIVE, AUTOMOTIVE SAFETY OR MEDICAL” INDUSTRY
DOMAINS ACCORDING TO ST PRODUCT DESIGN SPECIFICATIONS. PRODUCTS FORMALLY ESCC, QML OR JAN QUALIFIED ARE
DEEMED SUITABLE FOR USE IN AEROSPACE BY THE CORRESPONDING GOVERNMENTAL AGENCY.

Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.

© 2013 STMicroelectronics - All rights reserved

STMicroelectronics group of companies

Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan -
Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com

4/4 Doc ID 023625 Rev 2