CURRENT ELECTRICITY

3.1 Introduction
In Chapter 1 , all charges whether free or bound, were considered to be at rest. Charges in
motion constitute an electric current. Such currents occur naturally in many situations.
Lightning is one such phenomenon in which charges flow from the clouds to the earth
through the atmosphere, sometimes with disastrous results. The flow of charges in lightning
is not steady, but in our everyday life we see many devices where charges flow in a steady
manner, like water flowing smoothly in a river. A torch and a cell-driven clock are examples
of such devices. In the present chapter, we shall study some of the basic laws concerning
steady electric currents.
3.2 Electric CurRent
Imagine a small area held normal to the direction of flow of charges. Both the positive and
the negative charges may flow forward and backward across the area. In a given time
interval t , let q +¿¿be the net amount (i.e., forward minus backward) of positive charge that
flows in the forward direction across the area. Similarly, let q_ be the net amount of negative
charge flowing across the area in the forward direction. The net amount of charge flowing
across the area in the forward direction in the time interval t , then, is q=q +¿−q ¿. This is
_

proportional to t for steady current and the quotient

q
I= (3.1)
t
is defined to be the current across the area in the forward direction. (If it turn out to be a
negative number, it implies a current in the backward direction.)
Currents are not always steady and hence more generally, we define the current as follows.
Let Δ Q be the net charge flowing across a crosssection of a conductor during the time
interval Δ t [i.e., between times t and (t + Δt)¿. Then, the current at time t across the cross-
section of the conductor is defined as the value of the ratio of Δ Q to Δ t in the limit of Δ t
tending to zero,
lim Δ Q
Δt→0
I (t ) ≡ (3.2)
Δt
In SI units, the unit of current is ampere. An ampere is defined through magnetic effects of
currents that we will study in the following chapter. An ampere is typically the order of
magnitude of currents in domestic appliances. An average lightning carries currents of the
order of tens of thousands of amperes and at the other extreme, currents in our nerves are
in microamperes.
3.3 Electric Currents in Conductors
An electric charge will experience a force if an electric field is applied. If it is free to move, it
will thus move contributing to a current. In nature, free charged particles do exist like in
upper strata of atmosphere called the ionosphere. However, in atoms and molecules, the
negatively charged electrons and the positively charged nuclei are bound to each other and
are thus not free to move. Bulk matter is made up of many molecules, a gram of water, for
example, contains approximately 1022 molecules. These molecules are so closely packed that
the electrons are no longer attached to individual nuclei. In some materials, the electrons
will still be bound, i.e., they will not accelerate even if an electric field is applied. In other
materials, notably metals, some of the electrons are practically free to move within the bulk
material. These materials, generally called conductors, develop electric currents in them
when an electric field is applied.
If we consider solid conductors, then of course the atoms are tightly bound to each other so
that the current is carried by the negatively charged electrons. There are, however, other
types of conductors like electrolytic solutions where positive and negative charges both can
move. In our discussions, we will focus only on solid conductors so that the current is
carried by the negatively charged electrons in the background of fixed positive ions.
Consider first the case when no electric field is present. The electrons will be moving due to
thermal motion during which they collide with the fixed ions. An electron colliding with an
ion emerges with the same speed as before the collision. However, the direction of its
velocity after the collision is completely random. At a given time, there is no preferential
direction for the velocities of the electrons. Thus on the average, the number of electrons
travelling in any direction will be equal to the number of electrons travelling in the opposite
direction. So, there will be no net electric current.

FIGURE 3.1 Charges +Q and −Q put at the ends of a metallic cylinder. The current
thus will stop after a while unless the charges +Q and −Q are continuously
replenished.
Let us now see what happens to such a piece of conductor if an electric field is applied. To
focus our thoughts, imagine the conductor in the shape of a cylinder of radius R (Fig. 3.1).
Suppose we now take two thin circular discs of a dielectric of the same radius and put
positive charge +Q distributed over one disc and similarly −Q at the other disc. We attach
the two discs on the two flat surfaces of the cylinder. An electric field will be created and is
directed from the positive towards the negative charge. The electrons will drift because of
the electric field created to neutralise the charges. The electrons will be accelerated due to
this field towards +Q . They will thus move to neutralise the charges. The electrons, as long
as they are moving, will constitute an electric current. Hence in the situation considered,
there will be a current for a very short while and no current thereafter.
We can also imagine a mechanism where the ends of the cylinder are supplied with fresh
charges to make up for any charges neutralised by electrons moving inside the conductor.
In that case, there will be a steady electric field in the body of the conductor. This will result
in a continuous current rather than a current for a short period of time. Mechanisms, which
maintain a steady electric field are cells or batteries that we shall study later in this chapter.
In the next sections, we shall study the steady current that results from a steady electric
field in conductors.
3.4 OHM's LAW

(a)
 (b)

(c)
Illustrating the relation R = rl/A for a rectangular slab of length l and area of cross-
section A.

A basic law regarding flow of currents was discovered by G.S. Ohm in 1828, long before the
physical mechanism responsible for flow of currents was discovered. Imagine a conductor
through which a current I is flowing and let V be the potential difference between the ends
of the conductor. Then Ohm’s law states that
VI
Or, V = RI (3.3)
where the constant of proportionality R is called the resistance of the conductor. The SI
units of resistance is ohm, and is denoted by the symbol Ω . The resistance R not only
depends on the material of the conductor but also on the dimensions of the conductor. The
dependence of R on the dimensions of the conductor can easily be determined as follows.

Consider a conductor satisfying Eq. (3.3) to be in the form of a slab of length l and cross
sectional area A [Fig. 3.2(a)]. Imagine placing two such identical slabs side by side [Fig.
3.2(b)], so that the length of the combination is 2 l. The current flowing through the
combination is the same as that flowing through either of the slabs. If V is the potential
difference across the ends of the first slab, then V is also the potential difference across the
ends of the second slab since the second slab is identical to the first and the same current I
flows through both. The potential difference across the ends of the combination is clearly
sum of the potential difference across the two individual slabs and hence equals 2 V . The
current through the combination is I and the resistance of the combination RC is [from Eq.
(3.3)],
2V
RC = =2 R (3.4)
I
since V / I =R , the resistance of either of the slabs. Thus, doubling the length of a conductor
doubles the resistance. In general, then resistance is proportional to length,
R ∝l(3.5)
Next, imagine dividing the slab into two by cutting it lengthwise so that the slab can be
considered as a combination of two identical slabs of length l , but each having a cross
sectional area of A /2 [Fig. 3.2(c)].
For a given voltage V across the slab, if I is the current through the entire slab, then clearly
the current flowing through each of the two half-slabs is I /2. Since the potential difference
across the ends of the half-slabs is V , i.e., the same as across the full slab, the resistance of
each of the half-slabs R1 is
V V
R 1= =2 =2 R(3.6)
(I /2) I
Thus, halving the area of the cross-section of a conductor doubles the resistance. In general,
then the resistance R is inversely proportional to the cross-sectional area,
1
R∝ (3.7)
A
Combining Eqs. (3.5) and (3.7), we have
l
R∝ (3.8)
A
and hence for a given conductor
l
R=ρ (3.9)
A
where the constant of proportionality ρ depends on the material of the conductor but not
on its dimensions. ρ is called resistivity.
Using the last equation, Ohm's law reads
Id
V =I × R= (3.10)
A
Current per unit area (taken normal to the current), I / A , is called current density and is
denoted by j . The SI units of the current density are A /m2. Further, if E is the magnitude of
uniform electric field in the conductor whose length is l , then the potential difference V
across its
El= j ρ l or E = jp (3.11)
The above relation for magnitudes E and j can indeed be cast in a vector form. The current
density, (which we have defined as the current through unit area normal to the current) is
also directed along E , and is also a vector j ¿ ). Thus, the last equation can be written as,
E= j ρ(3.12)
or, j=σ E(3.13)
where σ ≡ 1/ ρ is called the conductivity. Ohm's law is often stated in an equivalent form, Eq.
(3.13) in addition to Eq.(3.3). In the next section, we will try to understand the origin of the
Ohm's law as arising from the characteristics of the drift of electrons.
3.5 Drift of Electrons and the Origin oF RESISTIVITY
As remarked before, an electron will suffer collisions with the heavy fixed ions, but after
collision, it will emerge with the same speed but in random directions. If we consider all the
electrons, their average velocity will be zero since their directions are random. Thus, if
there are N electrons and the velocity of the i th electron (i=1 , 2 ,3 , … N ) at a given time is
v i, then
N
1
N
∑ ❑v i =0(3.14)
i=1
Consider now the situation when an electric field is present. Electrons will be accelerated
due to this field by
−eE
a= (3.15)
m
where −e is the charge and m is the mass of an electron. Consider again the i th electron at a
given time t . This electron would have had its last collision some time before t , and let t i be
the time elapsed after its last collision. If v i was its velocity immediately after the last
collision, then its velocity V i at time t is
−eE
V i=v i + t (3.16)
m i

FIGURE 3.3 A schematic picture of an electron moving from a point A to another point
B through repeated collisions, and straight line travel between collisions (full lines).
If an electric field is applied as shown, the electron ends up at point B' (dotted lines).
A slight drift in a direction opposite the electric field is visible.

since starting with its last collision it was accelerated (Fig. 3.3) with an acceleration given
by Eq. (3.15) for a time interval t i. The average velocity of the electrons at time t is the
average of all the V i 's. The average of v i 's is zero [Eq. (3.14)] since immediately after any
collision, the direction of the velocity of an electron is completely random. The collisions of
the electrons do not occur at regular intervals but at random times. Let us denote by τ , the
average time between successive collisions. Then time more than τ and some less than τ . In
other words, the time t i in Eq. (3.16) will be less than τ for some and more than τ for others
as we go through the values of i=1 , 2 …. N . The average value of t i then is τ (known as
relaxation time). Thus, averaging Eq. (3.16) over the N -electrons at any given time t gives
us for the average velocity v d
eE
v d ≡ ( v i )average =( v i )average −
(t )
m i average
eE eE
=0- τ =- τ (3.17)
m m
This last result is surprising. It tells us that the electrons move with an average velocity
which is independent of time, although electrons are accelerated. This is the phenomenon of
drift and the velocity v d in Eq. (3.17) is called the drift velocity.
FIGURE 3.4 Current in a metallic conductor. The magnitude of current density in a
metal is the magnitude of charge contained in a cylinder of unit area and length v d.

Because of the drift, there will be net transport of charges across any area perpendicular to
E. Consider a planar area A , located inside the conductor such that the normal to the area is
parallel to E (Fig. 3.4). Then because of the drift, in an infinitesimal amount of time Δ t , all
electrons to the left of the area at distances upto |v d| Δ t would have crossed the area. If n is
the number of free electrons per unit volume in the metal, then there are n Δ t |v d| A such
electrons. Since each electron carries a charge −e , the total charge transported across this
area A to the right in time Δ t is −neA |v d| Δ t . E is directed towards the left and hence the
total charge transported along E across the area is negative of this. The amount of charge
crossing the area A in time Δ t is by definition [Eq. (3.2)] I Δ t , where I is the magnitude of
the current. Hence,
I Δt=+neA|v d| Δt(3.18)
Substituting the value of |v d| from Eq. (3.17)
2
e A
I Δ t= τ n Δ t |E|(3.19)
m
By definition I is related to the magnitude ¿ j∨¿ of the current density by
I =| j| A (3.20)
Hence, from Eqs.(3.19) and (3.20),
2
| j|= n e τ |E|(3.21)
m
The vector j is parallel to E and hence we can write Eq. (3.21) in the vector form
2
ne
j= τ E (3.22)
m
Comparison with Eq. (3.13) shows that Eq. (3.22) is exactly the Ohm's law, if we identify the
conductivity σ as
2
ne
σ= τ (3.23)
m
We thus see that a very simple picture of electrical conduction reproduces Ohm's law. We
have, of course, made assumptions that τ and n are constants, independent of E . We shall, in
the next section, discuss the limitations of Ohm's law.
Example 3.1 (a) Estimate the average drift speed of conduction electrons in a copper wire
of cross-sectional area 1.0 ×10−7 m2 carrying a current of 1.5 A . Assume that each copper
atom contributes roughly one conduction electron. The density of copper is
3 3
9 .0 ×10 kg/m , and its atomic mass is 63.5 u . (b) Compare the drift speed obtained above
with, (i) thermal speeds of copper atoms at ordinary temperatures, (ii) speed of
propagation of electric field along the conductor which causes the drift motion.
Solution
(a) The direction of drift velocity of conduction electrons is opposite to the electric field
direction, i.e., electrons drift in the direction of increasing potential. The drift speed v d is
given by Eq. (3.18) v d=(I /neA)
Now, e=1.6 × 10−19 C , A=1.0 ×10−7 m 2 , I =1.5 A . The density of conduction electrons, n
is equal to the number of atoms per cubic metre (assuming one conduction electron per Cu
atom as is reasonable from its valence electron count of one). A cubic metre of copper has a
mass of 9 .0 ×103 kg. Since 6.0 ×10 23 copper atoms have a mass of 63.5 g ,
23
6.0 × 10 6
n ¿ ×9.0 × 10
63.5
¿ ¿
which gives,
1.5
vd ¿ 28 −19 −7
8.5 ×10 ×1.6 ×10 × 1.0× 10
¿ ¿
(b) (i) At a temperature T , the thermal speed* of a copper atom of mass M is obtained from
[ ¿ (1/2) M v 2> ¿(3 /2)k B T ] and is thus typically of the order of √ k B T / M , where k B is the
Boltzmann constant. For copper at 300 K , this is about 2 ×102 m/ s. This figure indicates
the random vibrational speeds of copper atoms in a conductor. Note that the drift speed of
electrons is much smaller, about 10−5 times the typical thermal speed at ordinary
temperatures.
(ii) An electric field travelling along the conductor has a speed of an electromagnetic wave,
namely equal to 3.0 ×10 8 m s−1 (You will learn about this in Chapter 8). The drift speed is,
in comparison, extremely small; smaller by a factor of 10−11.
Example 3.2
(a) In Example 3.1, the electron drift speed is estimated to be only a few mm s−1 for currents
in the range of a few amperes? How then is current established almost the instant a circuit
is closed?
(b) The electron drift arises due to the force experienced by electrons in the electric field
inside the conductor. But force should cause acceleration. Why then do the electrons
acquire a steady average drift speed?
(c) If the electron drift speed is so small, and the electron's charge is small, how can we still
obtain large amounts of current in a conductor?
(d) When electrons drift in a metal from lower to higher potential, does it mean that all the
'free' electrons of the metal are moving in the same direction?
(e) Are the paths of electrons straight lines between successive collisions (with the positive
ions of the metal) in the (i) absence of electric field, (ii) presence of electric field?
Solution
(a) Electric field is established throughout the circuit, almost instantly (with the speed of
light) causing at every point a local electron drift. Establishment of a current does not have
to wait for electrons from one end of the conductor travelling to the other end. However, it
does take a little while for the current to reach its steady value.
(b) Each 'free' electron does accelerate, increasing its drift speed until it collides with a
positive ion of the metal. It loses its drift speed after collision but starts to accelerate and
increases its drift speed again only to suffer a collision again and so on. On the average,
therefore, electrons acquire only a drift speed.
(c) Simple, because the electron number density is enormous, ∼ 1029 m−3.
(d) By no means. The drift velocity is superposed over the large random velocities of
electrons.
(e) In the absence of electric field, the paths are straight lines; in the presence of electric
field, the paths are, in general, curved.
3.5.1 Mobility
As we have seen, conductivity arises from mobile charge carriers. In metals, these mobile
charge carriers are electrons; in an ionised gas, they are electrons and positive charged
ions; in an electrolyte, these can be both positive and negative ions.
An important quantity is the mobility μ defined as the magnitude of the drift velocity per
unit electric field:
|v d|
μ= (3.24)
E
The SI unit of mobility is m 2 /Vs and is 104 of the mobility in practical units ( cm2 /Vs ).
Mobility is positive. From Eq. (3.17), we have
eτE
v d=
m
Current
Electricity
Hence,
v d eτ
μ= = (3.25)
E m
where τ is the average collision time for electrons.
3.6 Limitations of Ohm's Law
Although Ohm's law has been found valid over a large class of materials, there do exist
materials and devices used in electric circuits where the proportionality of V and I does not
hold. The deviations broadly are one or more of the following types:
FIGURE 3.5 The dashed line represents the linear Ohm's law. The solid line is the
voltage V versus current I for a good conductor.

(a) V ceases to be proportional to I (Fig. 3.5).

(b) The relation between V and I depends on the sign of V . In other words, if I is the
current for a certain V , then reversing the direction of V keeping its magnitude fixed, does
not produce a current of the same magnitude as I in the opposite direction (Fig. 3.6). This
happens, for example, in a diode which we will study in Chapter 14 .

FIGURE 3.6 Characteristic curve of a diode. Note the different scales for negative and
positive values of the voltage and current.

FIGURE 3.7 Variation of current versus voltage for GaAs.

(c) The relation between V and I is not unique, i.e., there is more than one value of V for
the same current I (Fig. 3.7). A material exhibiting such behaviour is GaAs.
Materials and devices not obeying Ohm's law in the form of Eq. (3.3) are actually widely
used in electronic circuits. In this and a few subsequent chapters, however, we will study
the electrical currents in materials that obey Ohm's law.
3.7 Resistivity of Various Materials
The materials are classified as conductors, semiconductors and insulators depending on
their resistivities, in an increasing order of their values.
Metals have low resistivities in the range of 10−8 Ωm to 10−6 Ωm. At the other end are
insulators like ceramic, rubber and plastics having resistivities 1018 times greater than
metals or more. In between the two are the semiconductors. These, however, have
resistivities characteristically decreasing with a rise in temperature. The resistivities of
semiconductors can be decreased by adding small amount of suitable impurities. This last
feature is exploited in use of semiconductors for electronic devices.
3.8 Temperature Dependence of Resistivity
The resistivity of a material is found to be dependent on the temperature. Different
materials do not exhibit the same dependence on temperatures. Over a limited range of
temperatures, that is not too large, the resistivity of a metallic conductor is approximately
given by,
ρT =ρ0 [ 1+α ( T −T 0 ) ] (3.26)
where ρT is the resistivity at a temperature T and ρ0 is the same at a reference temperature
T 0. α is called the temperature co-efficient of resistivity, and from Eq. (3.26), the dimension
of α is (Temperature) −1. For metals, α is positive.
The relation of Eq. (3.26) implies that a graph of ρT plotted against T would be a straight
line. At temperatures much lower than 0∘ C , the graph, however, deviates considerably from
a straight line (Fig. 3.8).
Equation (3.26) thus, can be used approximately over a limited range of T around any
reference temperature T 0, where the graph can be approximated as a straight line.

Some

materials like Nichrome (which is an alloy of nickel, iron and chromium) exhibit a very
weak dependence of resistivity with temperature (Fig. 3.9). Manganin and constantan have
similar properties. These materials are thus widely used in wire bound standard resistors
since their resistance values would change very little with temperatures.

Unlike metals, the resistivities of semiconductors decrease with increasing temperatures. A

typical dependence is shown in Fig. 3.10.
We can qualitatively understand the temperature dependence of resistivity, in the light of
our derivation of Eq. (3.23). From this equation, resistivity of a material is given by
1 m
ρ= = 2 (3.27)
σ ne τ
ρ thus depends inversely both on the number n of free electrons per unit volume and on the
average time τ between collisions. As we increase temperature, average speed of the
electrons, which act as the carriers of current, increases resulting in more frequent
collisions. The average time of collisions τ , thus decreases with temperature.
In a metal, n is not dependent on temperature to any appreciable extent and thus the
decrease in the value of τ with rise in temperature causes ρ to increase as we have
observed.
For insulators and semiconductors, however, n increases with temperature. This increase
more than compensates any decrease in τ in Eq.(3.23) so that for such materials, ρ
decreases with temperature.
Example 3.3 An electric toaster uses nichrome for its heating element. When a negligibly
small current passes through it, its resistance at room temperature ( 27.0∘ C ) is found to be
75.3 Ω . When the toaster is connected to a 230 V supply, the current settles, after a few
seconds, to a steady value of 2.68 A. What is the steady temperature of the nichrome
element? The temperature coefficient of resistance of nichrome averaged over the
temperature range involved, is 1.70 ×10−4 ∘ C−1.
Solution When the current through the element is very small, heating effects can be ignored
and the temperature T 1 of the element is the same as room temperature. When the toaster
is connected to the supply, its initial current will be slightly higher than its steady value of
2.68 A . But due to heating effect of the current, the temperature will rise. This will cause an
increase in resistance and a slight decrease in current. In a few seconds, a steady state will
be reached when temperature will rise no further, and both the resistance of the element
and the current drawn will achieve steady values. The resistance R2 at the steady
temperature T 2 is
230 V
R 2= =85.8 Ω
2.68 A
Using the relation
R2=R 1 [ 1+α ( T 2 −T 1 ) ]
−4 ∘ −1
with α =1.70 ×10 C , we get
(85.8−75.3)
T 2−T 1 = −4
=820∘ C
(75.3)×1.70 × 10
that is, T 2=¿
Thus, the steady temperature of the heating element (when heating effect due to the current
equals heat loss to the surroundings) is 847 ∘ C .
Example 3.4 The resistance of the platinum wire of a platinum resistance thermometer at
the ice point is 5 Ω and at steam point is 5.23 Ω . When the thermometer is inserted in a hot
bath, the resistance of the platinum wire is 5.795 Ω . Calculate the temperature of the bath.
Solution R0 =5 Ω , R100 =5.23 Ω and Rt =5.795 Ω
Rt −R0
Now, t= ×100 , Rt =R0 (1+ αt)
R 100 −R0
 5.795−5
¿ ×100
5.23−5
0.795 ∘
¿ × 100=345.65 C
0.23
3.9 Electrical Energy, Power
Consider a conductor with end points A and B , in which a current I is flowing from A to B .
The electric potential at A and B are denoted by V ( A ) and V ( B) respectively. Since
current is flowing from A to B, V ( A )> V ( B) and the potential difference across AB is
V =V ( A)−V ( B)> 0.
In a time interval Δt , an amount of charge ΔQ=IΔt travels from A to B . The potential
energy of the charge at A , by definition, was QV ( A) and similarly at B, it is ΩV (B). Thus,
change in its potential energy Δ U pot is
Δ U pot =¿ Final potential energy - Initial potential energy
¿ ΔQ ¿
¿−IVΔt< 0(3.28)
If charges moved without collisions through the conductor, their kinetic energy would also
change so that the total energy is unchanged. Conservation of total energy would then imply
that,
ΔK =− Δ U pot (3.29)
that is,
ΔK =IVΔt >0 (3.30)
Thus, in case charges were moving freely through the conductor under the action of electric
field, their kinetic energy would increase as they move. We have, however, seen earlier that
on the average, charge carriers do not move with acceleration but with a steady drift
velocity. This is because of the collisions with ions and atoms during transit. During
collisions, the energy gained by the charges thus is shared with the atoms. The atoms
vibrate more vigorously, i.e., the conductor heats up. Thus, in an actual conductor, an
amount of energy dissipated as heat in the conductor during the time interval Δt is,
ΔW =IVΔt
The energy dissipated per unit time is the power dissipated P= ΔW / Δt and we have,
P=IV (3.32)
Using Ohm's law V =IR , we get
2
2 V
P=I R= (3.33)
R
as the power loss ("ohmic loss") in a conductor of resistance R carrying a current I . It is this
power which heats up, for example, the coil of an electric bulb to incandescence, radiating
out heat and light.
Where does the power come from? As we have reasoned before, we need an external source
to keep a steady current through the conductor. It is clearly this source which must supply
this power. In the simple circuit shown with a cell (Fig.3.11), it is the chemical energy of the
cell which supplies this power for as long as it can.
The expressions for power, Eqs. (3.32) and (3.33), show the dependence of the power
dissipated in a resistor R on the current through it and the voltage across it.
FIGURE 3.11 Heat is produced in the resistor R which is connected across the
terminals of a cell. The energy dissipated in the resistor R comes from the chemical
energy of the electrolyte.
Equation (3.33) has an important application to power transmission. Electrical power is
transmitted from power stations to homes and factories, which may be hundreds of miles
away, via transmission cables. One obviously wants to minimise the power loss in the
transmission cables connecting the power stations to homes and factories. We shall see now
how this can be achieved. Consider a device R , to which a power P is to be delivered via
transmission cables having a resistance Rc to be dissipated by it finally. If V is the voltage
across R and I the current through it, then
P=VI (3.34)
The connecting wires from the power station to the device has a finite resistance Rc . The
power dissipated in the connecting wires, which is wasted is Pc with
2
2 P Rc
Pc ¿ I R c = 2
(3.35)
V
from Eq. (3.32). Thus, to drive a device of power P , the power wasted in the connecting
wires is inversely proportional to V 2. The transmission cables from power stations are
hundreds of miles long and their resistance Rc is considerable. To reduce Pc , these wires
carry current at enormous values of V and this is the reason for the high voltage danger
signs on transmission lines - a common sight as we move away from populated areas. Using
electricity at such voltages is not safe and hence at the other end, a device called a
transformer lowers the voltage to a value suitable for use.
3.10 Cells, emf, Internal Resistance
 (a) (b)
FIGURE 3.12 (a) Sketch of an electrolyte cell with positive terminal P and negative
terminal N . The gap between the electrodes is exaggerated for clarity. A and B are
points in the electrolyte typically close to P and N . (b) the symbol for a cell, +
referring to P and - referring to the N electrode. Electrical connections to the cell are
made at P and N .

We have already mentioned that a simple device to maintain a steady current in an electric
circuit is the electrolytic cell. Basically a cell has two electrodes, called the positive (P) and
the negative (N ), as shown in Fig. 3.12. They are immersed in an electrolytic solution.
Dipped in the solution, the electrodes exchange charges with the electrolyte. The positive
electrode has a potential difference V +¿ ¿¿ between itself and the electrolyte solution
immediately adjacent to it marked A in the figure. Similarly, the negative electrode develops
a negative potential −¿ relative to the electrolyte adjacent to it, marked as B in the figure.
When there is no current, the electrolyte has the same potential throughout, so that the
potential difference between P and N is V +¿−(−V )=V ¿. This difference is called the
+ ¿+ V −¿ ¿ ¿

electromotive force (emf) of the cell and is denoted by ε . Thus

ε =V +¿+V −¿> 0( 3.36) ¿
¿
Note that ε is, actually, a potential difference and not a force. The name emf, however, is
used because of historical reasons, and was given at a time when the phenomenon was not
understood properly.
To understand the significance of ε , consider a resistor R connected across the cell (Fig.
3.12). A current I flows across R from C to D. As explained before, a steady current is
maintained because current flows from N to P through the electrolyte. Clearly, across the
electrolyte the same current flows through the electrolyte but from N to P , whereas
through R , it flows from P to N .
The electrolyte through which a current flows has a finite resistance r , called the internal
resistance. Consider first the situation when R is infinite so that I =V / R=0, where V is the
potential difference between P and N . Now,
V =¿ Potential difference between P and A
 Potential difference between A and B
 Potential difference between B and N
¿ε (3.37)
Thus, emf ε is the potential difference between the positive and negative electrodes in an
open circuit, i.e., when no current is flowing through the cell.
If however R is finite, I is not zero. In that case the potential difference between P and N is
V ¿
= ε −Ir (3.38)
Note the negative sign in the expression (Ir) for the potential difference between A and B.
This is because the current I flows from B to A in the electrolyte.
In practical calculations, internal resistances of cells in the circuit may be neglected when
the current I is such that ε > Ir . The actual values of the internal resistances of cells vary
from cell to cell. The internal resistance of dry cells, however, is much higher than the
common electrolytic cells.
We also observe that since V is the potential difference across R , we have from Ohm's law
V =IR (3.39)
IR=ε −Ir
ε
Or, I = (3.40)
R +r
The maximum current that can be drawn from a cell is for R=0 and it is I max=ε /r .
However, in most cells the maximum allowed current is much lower than this to prevent
permanent damage to the cell.
3.11 Cells in Series and in Parallel
Like resistors, cells can be combined together in an electric circuit. And like resistors, one
can, for calculating currents and voltages in a circuit, replace a combination of cells by an
equivalent cell.

FIGURE 3.13 Two cells of emf's ε 1 and ε 2 in the series. r 1 , r 2 are their internal
resistances. For connections across A and C , the combination can be considered as
∘
one cell of emf ε eq and an internal resistance r eq
Consider first two cells in series (Fig. 3.13), where one terminal of the two cells is joined
together leaving the other terminal in either cell free. ε 1 , ε 2 are the emf's of the two cells and
r 1 , r 2 their internal resistances, respectively.
Let V ( A ), V ( B) , V (C) be the potentials at points A , B and C shown in Fig. 3.13. Then
V ( A )−V ( B) is the potential difference between the positive and negative terminals of
the first cell. We have already calculated it in Eq. (3.38) and hence,
V AB ≡V ( A ) V ( B )=ε 1 I r 1 (3.41)
Similarly,
V BC ≡V ( B ) V ( C ) =ε 2 I r 2 (3.42)
Hence, the potential difference between the terminals A and C of the combination is
V AC ≡ V ( A)−V (C)=V ( A)−V ( B)+V ( B)−V (C)
If we wish to replace the combination by a single cell between A and C of emf ε eq and
internal resistance r eq , we would have
V AC =ε eq −I r eq (3.44)
Comparing the last two equations, we get
ε eq=ε 1 +ε 2 (3.45)
and r eq =r 1 +r 2 (3. 46)
In Fig.3.13, we had connected the negative electrode of the first to the positive electrode of
the second. If instead we connect the two negatives, Eq. (3.42) would change to
V BC =−ε 2−I r 2 and we will get
ε eq=ε 1−ε 2 ( ε 1> ε 2 ) (3.47)
The rule for series combination clearly can be extended to any number of cells:
(i) The equivalent emf of a series combination of n cells is just the sum of their individual
emf's, and
(ii) The equivalent internal resistance of a series combination of n cells is just the sum of
their internal resistances.
This is so, when the current leaves each cell from the positive electrode. If in the
combination, the current leaves any cell from the negative electrode, the emf of the cell
enters the expression for ε eq with a negative sign, as in Eq. (3.47).

FIGURE 3.14 Two cells in parallel. For connections across A and C , the combination
can be replaced by one cell of emf ε eq and internal resistances r eq whose values are
given in Eqs. (3.54) and (3.55).

Next, consider a parallel combination of the cells (Fig. 3.14). I 1 and I 2 are the currents
leaving the positive electrodes of the cells. At the point B1 , I 1 and I 2 flow in whereas the
current I flows out. Since as much charge flows in as out, we have
I =I 1+ I 2 (3.48)
Let V ( B1 ) and V ( B2 ) be the potentials at B1 and B2, respectively. Then, considering the first
cell, the potential difference across its terminals is V ( B1 )−V ( B2 ). Hence, from Eq. (3.38)
V ≡V ( B1 )−V ( B2 )=ε 1−I 1 r 1 (3.49)
Points B1 and B2 are connected exactly similarly to the second cell. Hence considering the
second cell, we also have
V ≡V ( B1 )−V ( B2 )=ε 2−I 2 r 2 (3.50)
Combining the last three equations
I ¿ I 1+ I 2
 ε 1−V ε 2−V
= +
r1 r2

= (
ε1 ε2
+ −V
r1 r2 ) (
1 1
+
r1 r2 ) (3.51)

Hence, V is given by,

ε1 r2 + ε2 r1 r1 r 2
V= −I (3.52)
r 1 +r 2 r 1 +r 2
If we want to replace the combination by a single cell, between B1 and B2, of emf ε eq and
internal resistance r eq , we would have
V =ε eq −I r eq (3.53)
The last two equations should be the same and hence
ε 1 r 2 +ε 2 r 1
ε eq= (3.54)
r 1 +r 2
r1 r 2
r eq= (3.55)
r 1 +r 2
We can put these equations in a simpler way,
1 1 1
= + (3.56)
r eq r 1 r 2
ε eq ε 1 ε 2
= + (3.57)
r eq r 1 r 2
In Fig. (3.14), we had joined the positive terminals together and similarly the two negative
ones, so that the currents I 1 , I 2 flow out of positive terminals. If the negative terminal of the
second is connected to positive terminal of the first, Eqs. (3.56) and (3.57) would still be
valid with ε 2 →−ε 2
Equations (3.56) and (3.57) can be extended easily. If there are n cells of emf ε 1 , … ε n and of
internal resistances r 1 , … r n respectively, connected in parallel, the combination is
equivalent to a single cell of emf ε eq and internal resistance r eq , such that
1 1 1
= +…+ (3.58)
r eq r 1 rn
ε eq ε 1 εn
= +…+ (3.59)
r eq r 1 rn

3.12 KIRCHHOFF's Rules

Electric circuits generally consist of a number of resistors and cells interconnected
sometimes in a complicated way. The formulae we have derived earlier for series and
parallel combinations of resistors are not always sufficient to determine all the currents and
potential differences in the circuit. Two rules, called Kirchhoff's rules, are very useful for
analysis of electric circuits.
Given a circuit, we start by labelling currents in each resistor by a symbol, say I , and a
directed arrow to indicate that a current I flows along the resistor in the direction
indicated. If ultimately I is determined to be positive, the actual current in the resistor is in
the direction of the arrow. If I turns out to be negative, the current actually flows in a
direction opposite to the arrow. Similarly, for each source (i.e., cell or some other source of
electrical power) the positive and negative electrodes are labelled, as well as, a directed
arrow with a symbol for the current flowing through the cell. This will tell us the potential
difference, V =V (P)−V ( N )=ε−Ir [Eq. (3.38) between the positive terminal P and the
negative terminal N ; I here is the current flowing from N to P through the cell]. If, while
labelling the current I through the cell one goes from P to N , then of course
V =ε + Ir (3.60)

FIGURE 3.15 At junction a the current leaving is I 1+ I 2 and current entering is I 3. The
junction rule says I 3=I 1+ I 2. At point h current entering is I 1. There is only one
current leaving h and by junction rule that will also be I 1. For the loops 'ahdcba' and
'ahdefga', the loop rules give −30 I 1−¿ 41 I 3+ 45=0 and −30 I 1+21 I 2−80=0.

Having clarified labelling, we now state the rules and the proof:

(a) Junction rule: At any junction, the sum of the currents entering the junction is equal to
the sum of currents leaving the junction (Fig. 3.15).
This applies equally well if instead of a junction of several lines, we consider a point in a
line.
The proof of this rule follows from the fact that when currents are steady, there is no
accumulation of charges at any junction or at any point in a line. Thus, the total current
flowing in, (which is the rate at which charge flows into the junction), must equal the total
current flowing out.
(b) Loop rule: The algebraic sum of changes in potential around any closed loop involving
resistors and cells in the loop is zero (Fig. 3.15).
This rule is also obvious, since electric potential is dependent on the location of the point.
Thus starting with any point if we come back to the same point, the total change must be
zero. In a closed loop, we do come back to the starting point and hence the rule.
Example 3.5 A battery of 10 V and negligible internal resistance is connected across the
diagonally opposite corners of a cubical network consisting of 12 resistors each of
resistance 1 Ω (Fig. 3.16). Determine the equivalent resistance of the network and the
current along each edge of the cube.
 FIGURE 3.16
Solution The network is not reducible to a simple series and parallel combinations of
resistors. There is, however, a clear symmetry in the problem which we can exploit to
obtain the equivalent resistance of the network.
The paths AA' , AD and AB are obviously symmetrically placed in the network. Thus, the
current in each must be the same, say, I. Further, at the corners A' , B and D , the incoming
current I must split equally into the two outgoing branches. In this manner, the current in
all the 12 edges of the cube are easily written down in terms of I , using Kirchhoffs first rule
and the symmetry in the problem.
Next take a closed loop, say, ABCC'EA, and apply Kirchhoffs second rule:
−IR−(1 /2)IR−IR +ε =0
where R is the resistance of each edge and ε the emf of battery. Thus,
5
ε = IR
2
The equivalent resistance Req of the network is
ε 5
Req = = R
3I 6
For R=1 Ω, Req =(5 /6)Ω and for ε =10 V , the total current ¿ ) in the network is
3 I =10 V /(5/6)Ω=12 A, i.e., I =4 A
The current flowing in each edge can now be read off from the Fig. 3.16.
It should be noted that because of the symmetry of the network, the great power of
Kirchhoff's rules has not been very apparent in Example 3.5. In a general network, there will
be no such simplification due to symmetry, and only by application of Kirchhoff's rules to
junctions and closed loops (as many as necessary to solve the unknowns in the network)
can we handle the problem. This will be illustrated in Example 3.6.
Example 3.6 Determine the current in each branch of the network shown in Fig. 3.17.

Figure 3.17
Solution Each branch of the network is assigned an unknown current to be determined by
the application of Kirchhoff's rules. To reduce the number of unknowns at the outset, the
first rule of Kirchhoff is used at every junction to assign the unknown current in each
branch. We then have three unknowns I 1 , I 2 and I 3 which can be found by applying the
second rule of Kirchhoff to three different closed loops. Kirchhoff's second rule for the
closed loop ADCA gives,
10−4 ( I 1−I 2 ) +2 ( I 2 + I 3−I 1 )−I 1=0 [3.61(a)]
that is, 7 I 1−6 I 2−2 I 3=10
For the closed loop ABCA, we get
10−4 I 2−2 ( I 2+ I 3 )−I 1=0 [3.61(b)]
that is, I 1+ 6 I 2 +2 I 3 =10
For the closed loop BCDEB, we get
5−2 ( I 2 + I 3) −2 ( I 2+ I 3−I 1 )=0
that is, 2 I 1−4 I 2−4 I 3 =−5 [3.61(c)]
Equations ( 3.61 a , b , c ) are three simultaneous equations in three unknowns. These can be
solved by the usual method to give
5 7
I 1=2.5 A , I 2= A , I 3=1 A
8 8
The currents in the various branches of the network are
5 1 7
AB: A , CA :2 A , DEB :1 A
8 2 8
7 1
AD :1 A ,CD :0 A , BC :2 A
8 2
It is easily verified that Kirchhoff's second rule applied to the remaining closed loops does
not provide any additional independent equation, that is, the above values of currents
satisfy the second rule for every closed loop of the network. For example, the total voltage
drop over the closed loop BADEB
5 15
5 V + ×4 V− ×4 V
8 8
equal to zero, as required by Kirchhoff's second rule.

3.13 Wheatstone Bridge

As an application of Kirchhoff's rules consider the circuit shown in Fig. 3.18, which is called
the Wheatstone bridge. The bridge has four resistors R1 , R 2 , R3 and R4 . Across one pair of
diagonally opposite points (A and C in the figure) a source is connected. This (i.e., AC) is
called the battery arm. Between the other two vertices, B and D, a galvanometer G (which is
a device to detect currents) is connected. This line, shown as BD in the figure, is called the
galvanometer arm.
For simplicity, we assume that the cell has no internal resistance. In general there will be
currents flowing across all the resistors as well as a current I g through G. Of special interest,
is the case of a balanced bridge where the resistors are such that I g=0. We can easily get
the balance condition, such that there is no current through G. In this case, the Kirchhoff's
junction rule applied to junctions D and B (see the figure) immediately gives us the relations
I 1=I 3 and I 2=I 4. Next, we apply Kirchhoff's loop rule to closed loops ADBA and CBDC. The
first loop gives
−I 1 R1 +0+ I 2 R 2=0 ( I g=0 ) (3.62)
and the second loop gives, upon using I 3=I 1 , I 4=I 2
I 2 R 4 +0−I 1 R 3=0 (3.63)
From Eq. (3.62), we obtain,
I 1 R2
=
I 2 R1
whereas from Eq. (3.63), we obtain,
I 1 R4
=
I 2 R3
Hence, we obtain the condition
R2 R4
= (3.64(a))
R1 R3
This last equation relating the four resistors is called the balance condition for the
galvanometer to give zero or null deflection.
The Wheatstone bridge and its balance condition provide a practical method for
determination of an unknown resistance. Let us suppose we have an unknown resistance,
which we insert in the fourth arm; R4 is thus not known. Keeping known resistances R1 and
R2 in the first and second arm of the bridge, we go on varying R3 till the galvanometer
shows a null deflection. The bridge then is balanced, and from the balance condition the
value of the unknown resistance R4 is given by,
R2
R4 =R3 (3.65 ( b ))
R1
A practical device using this principle is called the meter bridge.
Example 3.7 The four arms of a Wheatstone bridge (Fig. 3.19) have the following
resistances:
AB=100 Ω , BC =10 Ω , CD=5 Ω , and DA=60 Ω

FIGURE 3.19

A galvanometer of 15 Ω resistance is connected across BD. Calculate the current through the
galvanometer when a potential difference of 10 V is maintained across AC.
Solution Considering the mesh BADB, we have
100 I 1+15 I g −60 I 2=0
Or 20 I1 + 3Ig −¿ 12I2 = 0 [3.65(a)]
Considering the mesh BCDB, we have
10 ( I 1−I g )−15 I g −5 ( I 2 + I g ) =0
10 I 1−30 I g−5 I 2=0
2 I 1 −6 I g −I 2 = 0 [3.65(b)]
Considering the mesh ADCEA,
60 I 2+5 ( I 2 + I g )=10
65 I 2+5 I g =10
13I2 + Ig = 2 [3.65(c)]
Multiplying Eq. (3.65b) by 10
20 I 1−60 I g−10 I 2=0 [ 3.65 ( d ) ]
From Eqs. (3.65d) and (3.65a) we have
63 I g−2 I 2=0
I2 = 31.5 Ig [3.65e]
Substituting the value of I 2 into Eq. [3.65(c)], we get
13 ( 31.5 I g ) + I g=2
 410.5 I g =2
I g=4.87 mA.
 SUMMARY
1. Current through a given area of a conductor is the net charge passing per unit time
through the area.
2. To maintain a steady current, we must have a closed circuit in which an external
agency moves electric charge from lower to higher potential energy. The work done
per unit charge by the source in taking the charge from lower to higher potential
energy (i.e., from one terminal of the source to the other) is called the electromotive
force, or emf, of the source. Note that the emf is not a force; it is the voltage
difference between the two terminals of a source in open circuit.
3. Ohm's law: The electric current I flowing through a substance is proportional to the
voltage V across its ends, i.e., V ∝ I or V =RI , where R is called the resistance of the
substance. The unit of resistance is ohm: 1 Ω=1 V A−1.
4. The resistance R of a conductor depends on its length l and cross-sectional area A
ρl
through the relation, R= where ρ , called resistivity is a property of the material
A
and depends on temperature and pressure.
5. Electrical resistivity of substances varies over a very wide range. Metals have low
resistivity, in the range of 10−8 Ωm to 10−6 Ωm. Insulators like glass and rubber have
22 24
10 to 10 times greater resistivity. Semiconductors like Si and Ge lie roughly in the
middle range of resistivity on a logarithmic scale.
6. In most substances, the carriers of current are electrons; in some cases, for example,
ionic crystals and electrolytic liquids, positive and negative ions carry the electric
current
7. Current density j gives the amount of charge flowing per second per unit area
normal to the flow j=nq v d
where n is the number density (number per unit volume) of charge carriers each of
charge q , and v d is the drift velocity of the charge carriers. For electrons q=−e . If j
is normal to a cross-sectional area A and is constant over the area, the magnitude of
the current I through the area is ne v d A
2
eE ne
8. Using E=V /l, I =ne v d A , and Ohm's law, one obtains =ρ vd
m m
The proportionality between the force eE on the electrons in a metal due to the
external field E and the drift velocity v d (not acceleration) can be understood, if we
assume that the electrons suffer collisions with ions in the metal, which deflect them
randomly. If such collisions occur on an average at a time interval τ , v d=aτ=eEτ /m
m
where a is the acceleration of the electron. This gives ρ= 2
ne τ
9. In the temperature range in which resistivity increases linearly with temperature,
the temperature coefficient of resistivity α is defined as the fractional increase in
resistivity per unit increase in temperature
10. Ohm's law is obeyed by many substances, but it is not a fundamental law of nature.
It fails if
(a) V depends on I non-linearly.
(b) the relation between V and I depends on the sign of V for the same absolute
value of V
(c) The relation between V and I is non-unique.
 An example of (a) is when ρ increases with I (even if temperature is kept fixed). A
rectifier combines features (a) and (b). GaAs shows the feature (c).
11. When a source of emf ε is connected to an external resistance R , the voltage V ext
ε
across R is given by V ext =IR= R
R+r
where r is the internal resistance of the source.
12. Kirchhoff's Rules-
(a) Junction Rule: At any junction of circuit elements, the sum of currents entering
the junction must equal the sum of currents leaving it.
(b) Loop Rule: The algebraic sum of changes in potential around any closed loop
must be zero.
13. The Wheatstone bridge is an arrangement of four resistances −R1 , R 2, R3 , R 4 as
R1 R3
shown in the text. The null-point condition is given by = using which the value
R2 R4
of one resistance can be determined, knowing the other three resistances.
Physical Quantity Symbo Dimensions Unit Remark
l
Electric current I [A] A SI base unit
Charge Q,q [T A] C
Voltage, Electric V [ M L2 T −3 A−1 ] V Work/charge
potential difference
Electromotive force o [ M L2 ] V Work/charge
Resistance R [ M L2 T −3 A−2 ] Ω R=V /I
Resistivity [ ML3 T −3 A−2 ] Ωm R=ρl / A
Electrical [ M −1 L−3 T 3 A 2 ] S σ =1/ ρ
conductivity
Electric field E [ ML T −3 A−1 ] Vm
−1
Electric force
charge
Drift speed vd [ L T −1 ] −1
ms v d=
eEτ
m
Relaxation time τ [T ] s
Current density j [L −2
A] Am
−2
current/area
Mobility μ [ M L3 T −4 A−1 ]
2 −1
m V s
−1
vd/ E
 POINTS TO PONDER
1. Current is a scalar although we represent current with an arrow. Currents do not obey
the law of vector addition. That current is a scalar also follows from it's definition. The
current I through an area of cross-section is given by the scalar product of two vectors:
I = j⋅ Δ S where j and Δ S are vectors.
2. Refer to V −I curves of a resistor and a diode as drawn in the text. A resistor obeys
Ohm's law while a diode does not. The assertion that V =IR is a statement of Ohm's law
is not true. This equation defines resistance and it may be applied to all conducting
devices whether they obey Ohm's law or not. The Ohm's law asserts that the plot of I
versus V is linear i.e., R is independent of V .
Equation E=ρ j leads to another statement of Ohm's law, i.e., a conducting material
obeys Ohm's law when the resistivity of the material does not depend on the magnitude
and direction of applied electric field.
3. Homogeneous conductors like silver or semiconductors like pure germanium or
germanium containing impurities obey Ohm's law within some range of electric field
values. If the field becomes too strong, there are departures from Ohm's law in all cases.
4. Motion of conduction electrons in electric field E is the sum of (i) motion due to random
collisions and (ii) that due to E . The motion due to random collisions averages to zero
and does not contribute to v d (Chapter 10, Textbook of Class XI). v d, thus is only due to
applied electric field on the electron.
5. The relation j=ρ v should be applied to each type of charge carriers separately. In a
conducting wire, the total current and charge density arises from both positive and
negative charges:
j=ρ+¿ v + ¿+ ρ −¿ v ¿ ¿
−¿ ¿¿

ρ=ρ+¿+ρ −¿¿ ¿
Now in a neutral wire carrying electric current,
ρ+¿=− ρ
−¿¿ ¿
Further, v+ ¿∼ 0 ¿ which gives
ρ=0
j=ρ−¿ v ¿
Thus, the relation j=ρ v does not apply to the total current charge density.
6. Kirchhoff's junction rule is based on conservation of charge and the outgoing currents
add up and are equal to incoming current at a junction. Bending or reorienting the wire
does not change the validity of Kirchhoffs junction rule.
 EXERCISES
1. The storage battery of a car has an emf of 12 V . If the internal resistance of the battery
is 0.4 Ω, what is the maximum current that can be drawn from the battery?
2. A battery of emf 10 V and internal resistance 3 Ω is connected to a resistor. If the
current in the circuit is 0.5 A , what is the resistance of the resistor? What is the terminal
voltage of the battery when the circuit is closed?
3. At room temperature ( 27.0∘ C ) the resistance of a heating element is 100 Ω . What is the
temperature of the element if the resistance is found to be 117 Ω, given that the
temperature coefficient of the material of the resistor is 1.70 ×10−4 ∘ C−1.
4. A negligibly small current is passed through a wire of length 15 m and uniform cross-
section 6 .0 ×10−7 m 2, and its resistance is measured to be 5.0 Ω . What is the resistivity
of the material at the temperature of the experiment?
5. A silver wire has a resistance of 2.1 Ω at 27.5∘ C , and a resistance of 2.7 Ω at 100 ∘ C .
Determine the temperature coefficient of resistivity of silver.
6. A heating element using nichrome connected to a 230 V supply draws an initial current
of 3.2 A which settles after a few seconds to a steady value of 2.8 A . What is the steady
temperature of the heating element if the room temperature is 27.0∘ C ? Temperature
coefficient of resistance of nichrome averaged over the temperature range involved is
−4 ∘ −1
1.70 ×10 C .
7. Determine the current in each branch of the network shown in Fig. 3.20:

FIGURE 3.20

8. A storage battery of emf 8.0 V and internal resistance 0.5 Ω is being charged by a 120 V
dc supply using a series resistor of 15.5 Ω . What is the terminal voltage of the battery
during charging? What is the purpose of having a series resistor in the charging circuit?
9. The number density of free electrons in a copper conductor estimated in Example 3.1 is
28 −3
8 .5 ×10 m . How long does an electron take to drift from one end of a wire 3.0 m
long to its other end? The area of cross-section of the wire is 2.0 ×10−6 m2 and it is
carrying a current of 3.0 A.