CARBON REMOVER

Wilhelmsen Ships Service AS

Part Number: 571604 (25L steel drums) Issue Date: 29/05/2024
Version No: 13.42 Print Date: 26/07/2024
Safety Data Sheet (Conforms to Annex II of REACH (1907/2006) - Regulation 2020/878) L.REACH.NOR.EN

SECTION 1 Identification of the substance / mixture and of the company / undertaking

1.1. Product Identifier

Product name CARBON REMOVER

Chemical Name Not Applicable

Synonyms Pr No: 2911 (Norwegian Product Register)
Proper shipping name TOXIC LIQUID, ORGANIC, N.O.S. (Xylenol, Dichlorotoluene mixture)
Chemical formula Not Applicable
Other means of
571604 (25L steel drums), 571604 | UFI:YS12-TNYQ-X10R-52FQ
identification

1.2. Relevant identified uses of the substance or mixture and uses advised against
Chemical Product
PC35 Washing and cleaning products
Category

Sectors of Use SU3 Industrial uses

Relevant identified uses Heavy duty solvent cleaner

Uses advised against No specific uses advised against are identified.

1.3. Details of the manufacturer or supplier of the safety data sheet

Outback (M)SDS portal:
Wilhelmsen Ships Service AS*
Registered company name Wilhelmsen Ships Service AS http://jr.chemwatch.net/outb/account/autologin?
Central Warehouse
login=wilhelmsen

--------Use our Outback portal to obtain our

(M)SDSs in other languages and/or format.---------
Strandveien 20 Lysaker 1366 Willem Barentszstraat 50
Address For questions relating to our SDSs please use
Norway Rotterdam Netherlands
Email: [email protected]
--------- Norway
Telephone +47 67 58 40 00 Not Available +31 10 4877 777

Fax Not Available Not Available Not Available

Website http://www.wilhelmsen.com/ http://www.wilhelmsen.com http://www.wilhelmsen.com

Email [email protected] [email protected] [email protected]

1.4. Emergency telephone number

Association / Organisation Giftinformasjonssentralen - 24 timer 24hrs - Chemwatch Dutch nat. poison centre

Emergency telephone
+47 22591300 +31-10-4877700 + 31 88 7558561
numbers

Other emergency
+31-10-4877700 +31-10-4877700 + 31 10 4877700
telephone numbers

Association / Organisation CHEMWATCH EMERGENCY RESPONSE (24/7)

Emergency telephone
+47 23 25 25 84
numbers

Page 1 continued...
Part Number: 571604 (25L steel drums) Page 2 of 16 Issue Date: 29/05/2024
Version No: 13.42 Print Date: 26/07/2024
CARBON REMOVER

Other emergency
+61 3 9573 3188
telephone numbers

Once connected and if the message is not in your preferred language then please dial 01

SECTION 2 Hazards identification

2.1. Classification of the substance or mixture

Classification according to H301 - Acute Toxicity (Oral) Category 3, H304 - Aspiration Hazard Category 1, H311 - Acute Toxicity (Dermal) Category 3, H314 -
regulation (EC) No Skin Corrosion/Irritation Category 1C, H317 - Sensitisation (Skin) Category 1, H336 - Specific Target Organ Toxicity - Single
1272/2008 [CLP] and Exposure (Narcotic Effects) Category 3, H372 - Specific Target Organ Toxicity - Repeated Exposure Category 1, H411 -
amendments [1] Hazardous to the Aquatic Environment Long-Term Hazard Category 2

Legend: 1. Classified by Chemwatch; 2. Classification drawn from Regulation (EU) No 1272/2008 - Annex VI

2.2. Label elements

Hazard pictogram(s)

Signal word Danger

Hazard statement(s)
H301 Toxic if swallowed.
H304 May be fatal if swallowed and enters airways.

H311 Toxic in contact with skin.

H314 Causes severe skin burns and eye damage.
H317 May cause an allergic skin reaction.

H336 May cause drowsiness or dizziness.

H372 Causes damage to organs through prolonged or repeated exposure.
H411 Toxic to aquatic life with long lasting effects.

Supplementary statement(s)
Not Applicable

Precautionary statement(s) General

P101 If medical advice is needed, have product container or label at hand.
P102 Keep out of reach of children.
P103 Read carefully and follow all instructions.

Precautionary statement(s) Prevention

P260 Do not breathe mist/vapours/spray.
P264 Wash all exposed external body areas thoroughly after handling.
P270 Do not eat, drink or smoke when using this product.

P271 Use only outdoors or in a well-ventilated area.

P280 Wear protective gloves, protective clothing, eye protection and face protection.
P273 Avoid release to the environment.

P272 Contaminated work clothing should not be allowed out of the workplace.

Precautionary statement(s) Response

P301+P310 IF SWALLOWED: Immediately call a POISON CENTER/doctor/physician/first aider.
P301+P330+P331 IF SWALLOWED: Rinse mouth. Do NOT induce vomiting. If more than 15 mins from Doctor, INDUCE VOMITING (if conscious).
P303+P361+P353 IF ON SKIN (or hair): Take off immediately all contaminated clothing. Rinse skin with water [or shower].

P305+P351+P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
P302+P352 IF ON SKIN: Wash with plenty of water and soap.

Continued...
Part Number: 571604 (25L steel drums) Page 3 of 16 Issue Date: 29/05/2024
Version No: 13.42 Print Date: 26/07/2024
CARBON REMOVER

P363 Wash contaminated clothing before reuse.

P333+P313 If skin irritation or rash occurs: Get medical advice/attention.

P361+P364 Take off immediately all contaminated clothing and wash it before reuse.
P391 Collect spillage.

P304+P340 IF INHALED: Remove person to fresh air and keep comfortable for breathing.

Precautionary statement(s) Storage

P405 Store locked up.

P403+P233 Store in a well-ventilated place. Keep container tightly closed.

Precautionary statement(s) Disposal

P501 Dispose of contents/container to authorised hazardous or special waste collection point in accordance with any local regulation.

Material contains Hydrocarbons, C10-C13, n-alkanes, isoalkanes, cyclics, aromatics (2-25%)-, Hydrocarbones, C10, aromatics, <1% naphtalene, tar acids, 3,5-
xylenol fraction.

2.3. Other hazards

tar acids, 3,5-xylenol
Listed in the Europe Regulation (EC) No 1907/2006 - Annex XVII (Restrictions may apply)
fraction

SECTION 3 Composition / information on ingredients

3.1.Substances
See 'Composition on ingredients' in Section 3.2

3.2.Mixtures
1. CAS No
Nanoform
2.EC No % Classification according to regulation (EC) No SCL / M-
Name Particle
3.Index No [weight] 1272/2008 [CLP] and amendments Factor
Characteristics
4.REACH No

Not
Available

1. 29797-40-8* Acute M
Skin Corrosion/Irritation Category 2, Hazardous to
2.249-854-8 the Aquatic Environment Long-Term Hazard factor:
30-60 dichlorotoluene Not Available
3.Not Available 1000
4.Not Available Category 1; H315, H410 [1]
Chronic M
factor: Not
Available

0
Aspiration Hazard Category 1, Specific Target Acute M
1. Not Available Hydrocarbons, C10-
Organ Toxicity - Repeated Exposure Category 1, factor: Not
2.919-164-8 C13, n-alkanes,
10-30 Hazardous to the Aquatic Environment Long-Term Available Not Available
3.Not Available isoalkanes, cyclics,
Hazard Category 3; H304, H372, H412, EUH066
4.01-21194739 77-17-0004 aromatics (2-25%)- [1]
Chronic M
factor: Not
Available

0
Aspiration Hazard Category 1, Specific Target Acute M
1. Not Available
Hydrocarbones, C10, Organ Toxicity - Single Exposure (Narcotic Effects) factor: Not
2.918-811-1
10-30 aromatics, <1% Category 3, Hazardous to the Aquatic Environment Available Not Available
3.Not Available
naphtalene Long-Term Hazard Category 2; H304, H336, H411,
4.01-21194635 83-34-000 Chronic M
EUH066 [1] factor: Not
Available

Not
Acute Toxicity (Oral) Category 3, Acute Toxicity Available
(Dermal) Category 3, Skin Corrosion/Irritation
1. 84989-06-0* Category 1B, Sensitisation (Skin) Category 1, Acute M
2.284-896-0 tar acids, 3,5-xylenol factor: Not
20 Serious Eye Damage/Eye Irritation Category 1, Not Available
3.648-122-00-9 fraction Available
Hazardous to the Aquatic Environment Long-Term
4.Not Available
Hazard Category 2; H301, H311, H314, H317, Chronic M
H318, H411 [1] factor: Not
Available

Continued...
Part Number: 571604 (25L steel drums) Page 4 of 16 Issue Date: 29/05/2024
Version No: 13.42 Print Date: 26/07/2024
CARBON REMOVER

Legend: 1. Classified by Chemwatch; 2. Classification drawn from Regulation (EU) No 1272/2008 - Annex VI; 3. Classification drawn from
C&L; * EU IOELVs available; [e] Substance identified as having endocrine disrupting properties

SECTION 4 First aid measures

4.1. Description of first aid measures

If this product comes in contact with the eyes:
Wash out immediately with fresh running water.
Ensure complete irrigation of the eye by keeping eyelids apart and away from eye and moving the eyelids by occasionally
Eye Contact
lifting the upper and lower lids.
Seek medical attention without delay; if pain persists or recurs seek medical attention.
Removal of contact lenses after an eye injury should only be undertaken by skilled personnel.

If skin or hair contact occurs:

Skin Contact Flush skin and hair with running water (and soap if available).
Seek medical attention in event of irritation.
If fumes or combustion products are inhaled remove from contaminated area.
Lay patient down. Keep warm and rested.
Prostheses such as false teeth, which may block airway, should be removed, where possible, prior to initiating first aid
Inhalation procedures.
Apply artificial respiration if not breathing, preferably with a demand valve resuscitator, bag-valve mask device, or pocket
mask as trained. Perform CPR if necessary.
Transport to hospital, or doctor, without delay.
If swallowed do NOT induce vomiting.
If vomiting occurs, lean patient forward or place on left side (head-down position, if possible) to maintain open airway and
prevent aspiration.
Observe the patient carefully.
Ingestion Never give liquid to a person showing signs of being sleepy or with reduced awareness; i.e. becoming unconscious.
Give water to rinse out mouth, then provide liquid slowly and as much as casualty can comfortably drink.
Seek medical advice.
If spontaneous vomiting appears imminent or occurs, hold patient's head down, lower than their hips to help avoid possible
aspiration of vomitus.

4.2 Most important symptoms and effects, both acute and delayed
See Section 11

4.3. Indication of any immediate medical attention and special treatment needed
Any material aspirated during vomiting may produce lung injury. Therefore emesis should not be induced mechanically or pharmacologically. Mechanical means
should be used if it is considered necessary to evacuate the stomach contents; these include gastric lavage after endotracheal intubation. If spontaneous vomiting
has occurred after ingestion, the patient should be monitored for difficult breathing, as adverse effects of aspiration into the lungs may be delayed up to 48 hours.
As in all cases of suspected poisoning, follow the ABCDEs of emergency medicine (airway, breathing, circulation, disability, exposure), then the ABCDEs of
toxicology (antidotes, basics, change absorption, change distribution, change elimination).
For poisons (where specific treatment regime is absent):
--------------------------------------------------------------
BASIC TREATMENT
--------------------------------------------------------------
Establish a patent airway with suction where necessary.
Watch for signs of respiratory insufficiency and assist ventilation as necessary.
Administer oxygen by non-rebreather mask at 10 to 15 L/min.
Monitor and treat, where necessary, for pulmonary oedema.
Monitor and treat, where necessary, for shock.
Anticipate seizures.
DO NOT use emetics. Where ingestion is suspected rinse mouth and give up to 200 ml water (5 ml/kg recommended) for dilution where patient is able to
swallow, has a strong gag reflex and does not drool.
--------------------------------------------------------------
ADVANCED TREATMENT
--------------------------------------------------------------
Consider orotracheal or nasotracheal intubation for airway control in unconscious patient or where respiratory arrest has occurred.
Positive-pressure ventilation using a bag-valve mask might be of use.
Monitor and treat, where necessary, for arrhythmias.
Start an IV D5W TKO. If signs of hypovolaemia are present use lactated Ringers solution. Fluid overload might create complications.
Drug therapy should be considered for pulmonary oedema.
Hypotension with signs of hypovolaemia requires the cautious administration of fluids. Fluid overload might create complications.
Treat seizures with diazepam.
Proparacaine hydrochloride should be used to assist eye irrigation.
BRONSTEIN, A.C. and CURRANCE, P.L.
EMERGENCY CARE FOR HAZARDOUS MATERIALS EXPOSURE: 2nd Ed. 1994

SECTION 5 Firefighting measures

Continued...
Part Number: 571604 (25L steel drums) Page 5 of 16 Issue Date: 29/05/2024
Version No: 13.42 Print Date: 26/07/2024
CARBON REMOVER

5.1. Extinguishing media

Water spray or fog.
Foam.
Dry chemical powder.
BCF (where regulations permit).
Carbon dioxide.

5.2. Special hazards arising from the substrate or mixture

Avoid contamination with oxidising agents i.e. nitrates, oxidising acids, chlorine bleaches, pool chlorine etc. as ignition may
Fire Incompatibility
result

5.3. Advice for firefighters

Alert Fire Brigade and tell them location and nature of hazard.
Wear full body protective clothing with breathing apparatus.
Prevent, by any means available, spillage from entering drains or water course.
Fire Fighting Use fire fighting procedures suitable for surrounding area.
Do not approach containers suspected to be hot.
Cool fire exposed containers with water spray from a protected location.
If safe to do so, remove containers from path of fire.

carbon dioxide (CO2)

,
Fire/Explosion Hazard
other pyrolysis products typical of burning organic material.
May emit poisonous fumes.

SECTION 6 Accidental release measures

6.1. Personal precautions, protective equipment and emergency procedures

See section 8

6.2. Environmental precautions

See section 12

6.3. Methods and material for containment and cleaning up

Clean up all spills immediately.
Avoid breathing vapours and contact with skin and eyes.
Control personal contact with the substance, by using protective equipment.
Minor Spills
Contain and absorb spill with sand, earth, inert material or vermiculite.
Wipe up.
Place in a suitable, labelled container for waste disposal.
Clear area of personnel and move upwind.
Alert Fire Brigade and tell them location and nature of hazard.
Wear full body protective clothing with breathing apparatus.
Major Spills Prevent, by any means available, spillage from entering drains or water course.
Stop leak if safe to do so.
Contain spill with sand, earth or vermiculite.
Collect recoverable product into labelled containers for recycling.

6.4. Reference to other sections

Personal Protective Equipment advice is contained in Section 8 of the SDS.

SECTION 7 Handling and storage

7.1. Precautions for safe handling

Avoid all personal contact, including inhalation.
Wear protective clothing when risk of exposure occurs.
Use in a well-ventilated area.
Safe handling Prevent concentration in hollows and sumps.
DO NOT enter confined spaces until atmosphere has been checked.
DO NOT allow material to contact humans, exposed food or food utensils.
Avoid contact with incompatible materials.
Fire and explosion
See section 5
protection
Other information Store in original containers.
Keep containers securely sealed.
Store in a cool, dry, well-ventilated area.
Store away from incompatible materials and foodstuff containers.

Continued...
Part Number: 571604 (25L steel drums) Page 6 of 16 Issue Date: 29/05/2024
Version No: 13.42 Print Date: 26/07/2024
CARBON REMOVER

Protect containers against physical damage and check regularly for leaks.
Observe manufacturer's storage and handling recommendations contained within this SDS.

7.2. Conditions for safe storage, including any incompatibilities

Lined metal can, lined metal pail/ can.
Plastic pail.
Polyliner drum.
Packing as recommended by manufacturer.
Check all containers are clearly labelled and free from leaks.
For low viscosity materials
Drums and jerricans must be of the non-removable head type.
Where a can is to be used as an inner package, the can must have a screwed enclosure.
For materials with a viscosity of at least 2680 cSt. (23 deg. C) and solids (between 15 C deg. and 40 deg C.):
Removable head packaging;
Suitable container Cans with friction closures and
low pressure tubes and cartridges
may be used.
-
Where combination packages are used, and the inner packages are of glass, there must be sufficient inert cushioning material in
contact with inner and outer packages *.
-
In addition, where inner packagings are glass and contain liquids of packing group I and II there must be sufficient inert
absorbent to absorb any spillage *.
-
* unless the outer packaging is a close fitting moulded plastic box and the substances are not incompatible with the plastic.
Storage incompatibility Avoid reaction with oxidising agents

Hazard categories in
accordance with
E2: Hazardous to the Aquatic Environment in Category Chronic 2
Regulation (EC) No
2012/18/EU (Seveso III)
Qualifying quantity
(tonnes) of dangerous
substances as referred to E2 Lower- / Upper-tier requirements: 200 / 500
in Article 3(10) for the
application of

+ x o x + + o

X — Must not be stored together

0 — May be stored together with specific preventions
+ — May be stored together

Note: Depending on other risk factors, compatibility assessment based on the table above may not be relevant to storage situations, particularly where large volumes
of dangerous goods are stored and handled. Reference should be made to the Safety Data Sheets for each substance or article and risks assessed accordingly.

7.3. Specific end use(s)

See section 1.2

SECTION 8 Exposure controls / personal protection

8.1. Control parameters

DNELs PNECs
Ingredient
Exposure Pattern Worker Compartment
7.8 µg/L (Water (Fresh))
Dermal 4.2 mg/kg bw/day (Systemic, Chronic)
12.6 µg/L (Water - Intermittent release)
Inhalation 14.8 mg/m³ (Systemic, Chronic)
0.78 µg/L (Water (Marine))
Inhalation 29.6 mg/m³ (Systemic, Acute)
1.04 mg/kg sediment dw (Sediment (Fresh Water))
dichlorotoluene Dermal 1.5 mg/kg bw/day (Systemic, Chronic) *
0.104 mg/kg sediment dw (Sediment (Marine))
Inhalation 2.6 mg/m³ (Systemic, Chronic) *
66.2 mg/kg soil dw (Soil)
Oral 1.5 mg/kg bw/day (Systemic, Chronic) *
1.37 mg/L (STP)
Inhalation 5.2 mg/m³ (Systemic, Acute) *
44.44 mg/kg food (Oral)
100 µg/L (Water (Fresh))
24 µg/L (Water - Intermittent release)
Inhalation 4.9 mg/m³ (Systemic, Chronic)
10 µg/L (Water (Marine))
Inhalation 0.87 mg/m³ (Systemic, Chronic) *
tar acids, 3,5-xylenol fraction 1.84 mg/kg sediment dw (Sediment (Fresh Water))
Oral 0.25 mg/kg bw/day (Systemic, Chronic) *
0.184 mg/kg sediment dw (Sediment (Marine))
Oral 17.5 mg/kg bw/day (Systemic, Acute) *
0.096 mg/kg soil dw (Soil)
1.14 mg/L (STP)

Continued...
Part Number: 571604 (25L steel drums) Page 7 of 16 Issue Date: 29/05/2024
Version No: 13.42 Print Date: 26/07/2024
CARBON REMOVER

* Values for General Population

Occupational Exposure Limits (OEL)

INGREDIENT DATA

Source Ingredient Material name TWA STEL Peak Notes

Not Available Not Available Not Available Not Available Not Available Not Available Not Available

Not Applicable

Emergency Limits

Ingredient TEEL-1 TEEL-2 TEEL-3

CARBON REMOVER Not Available Not Available Not Available

Ingredient Original IDLH Revised IDLH

dichlorotoluene Not Available Not Available
Hydrocarbons, C10-C13, n-
alkanes, isoalkanes, cyclics, Not Available Not Available
aromatics (2-25%)-
Hydrocarbones, C10,
Not Available Not Available
aromatics, <1% naphtalene
tar acids, 3,5-xylenol fraction Not Available Not Available

Occupational Exposure Banding

Ingredient Occupational Exposure Band Rating Occupational Exposure Band Limit

dichlorotoluene E ≤ 0.1 ppm
tar acids, 3,5-xylenol fraction E ≤ 0.01 mg/m³

Notes: Occupational exposure banding is a process of assigning chemicals into specific categories or bands based on a chemical's
potency and the adverse health outcomes associated with exposure. The output of this process is an occupational exposure
band (OEB), which corresponds to a range of exposure concentrations that are expected to protect worker health.

MATERIAL DATA
Sensory irritants are chemicals that produce temporary and undesirable side-effects on the eyes, nose or throat. Historically occupational exposure standards for
these irritants have been based on observation of workers' responses to various airborne concentrations. Present day expectations require that nearly every
individual should be protected against even minor sensory irritation and exposure standards are established using uncertainty factors or safety factors of 5 to 10 or
more. On occasion animal no-observable-effect-levels (NOEL) are used to determine these limits where human results are unavailable. An additional approach,
typically used by the TLV committee (USA) in determining respiratory standards for this group of chemicals, has been to assign ceiling values (TLV C) to rapidly
acting irritants and to assign short-term exposure limits (TLV STELs) when the weight of evidence from irritation, bioaccumulation and other endpoints combine to
warrant such a limit. In contrast the MAK Commission (Germany) uses a five-category system based on intensive odour, local irritation, and elimination half-life.
However this system is being replaced to be consistent with the European Union (EU) Scientific Committee for Occupational Exposure Limits (SCOEL); this is
more closely allied to that of the USA.
NOTE J: The classification as a carcinogen need not apply if it can be shown that the substance contains less than 0.1%w/w benzene (EINECS No 200-753-7). -
European Union (EU) List of harmonised classification and labelling hazardous substances, Table 3.1, Annex VI, Regulation (EC) No 1272/2008 (CLP) - up to the
latest ATP
NOTE M: The classification as a carcinogen need not apply if it can be shown that the substance contains less than 0.005% w/w benzo[a]pyrene (EINECS No
200-028-5). This note applies only to certain complex oil-derived substances in Annex IV.
European Union (EU) List of harmonised classification and labelling hazardous substances, Table 3.1, Annex VI, Regulation (EC) No 1272/2008 (CLP) - up to the
latest ATP

8.2. Exposure controls

Engineering controls are used to remove a hazard or place a barrier between the worker and the hazard. Well-designed
engineering controls can be highly effective in protecting workers and will typically be independent of worker interactions to
provide this high level of protection.
The basic types of engineering controls are:
8.2.1. Appropriate
Process controls which involve changing the way a job activity or process is done to reduce the risk.
engineering controls
Enclosure and/or isolation of emission source which keeps a selected hazard "physically" away from the worker and ventilation
that strategically "adds" and "removes" air in the work environment. Ventilation can remove or dilute an air contaminant if
designed properly. The design of a ventilation system must match the particular process and chemical or contaminant in use.
Employers may need to use multiple types of controls to prevent employee overexposure.

8.2.2. Individual protection

measures, such as
personal protective
equipment

Eye and face protection Safety glasses with side shields.

Chemical goggles. [AS/NZS 1337.1, EN166 or national equivalent]
Contact lenses may pose a special hazard; soft contact lenses may absorb and concentrate irritants. A written policy
document, describing the wearing of lenses or restrictions on use, should be created for each workplace or task. This should

Continued...
Part Number: 571604 (25L steel drums) Page 8 of 16 Issue Date: 29/05/2024
Version No: 13.42 Print Date: 26/07/2024
CARBON REMOVER

include a review of lens absorption and adsorption for the class of chemicals in use and an account of injury experience.
Medical and first-aid personnel should be trained in their removal and suitable equipment should be readily available. In the
event of chemical exposure, begin eye irrigation immediately and remove contact lens as soon as practicable.
Skin protection See Hand protection below
The selection of suitable gloves does not only depend on the material, but also on further marks of quality which vary from
manufacturer to manufacturer. Where the chemical is a preparation of several substances, the resistance of the glove material
can not be calculated in advance and has therefore to be checked prior to the application.
The exact break through time for substances has to be obtained from the manufacturer of the protective gloves and has to be
Hands/feet protection observed when making a final choice.
Personal hygiene is a key element of effective hand care. Gloves must only be worn on clean hands. After using gloves, hands
should be washed and dried thoroughly. Application of a non-perfumed moisturiser is recommended.
Wear chemical protective gloves, e.g. PVC.
Wear safety footwear or safety gumboots, e.g. Rubber
Body protection See Other protection below
Overalls.
Eyewash unit.
Other protection
Barrier cream.
Skin cleansing cream.

Respiratory protection
Type A Filter of sufficient capacity. (AS/NZS 1716 & 1715, EN 143:2000 & 149:2001, ANSI Z88 or national equivalent)

Selection of the Class and Type of respirator will depend upon the level of breathing zone contaminant and the chemical nature of the contaminant. Protection
Factors (defined as the ratio of contaminant outside and inside the mask) may also be important.

Required minimum protection Maximum gas/vapour concentration present in air p.p.m. (by Half-face Full-Face
factor volume) Respirator Respirator
up to 10 1000 A-AUS / Class1 -
up to 50 1000 - A-AUS / Class 1
up to 50 5000 Airline * -
up to 100 5000 - A-2

up to 100 10000 - A-3

100+ Airline**

* - Continuous Flow ** - Continuous-flow or positive pressure demand

A(All classes) = Organic vapours, B AUS or B1 = Acid gasses, B2 = Acid gas or hydrogen cyanide(HCN), B3 = Acid gas or hydrogen cyanide(HCN), E = Sulfur
dioxide(SO2), G = Agricultural chemicals, K = Ammonia(NH3), Hg = Mercury, NO = Oxides of nitrogen, MB = Methyl bromide, AX = Low boiling point organic
compounds(below 65 degC)

Cartridge respirators should never be used for emergency ingress or in areas of unknown vapour concentrations or oxygen content.
The wearer must be warned to leave the contaminated area immediately on detecting any odours through the respirator. The odour may indicate that the mask
is not functioning properly, that the vapour concentration is too high, or that the mask is not properly fitted. Because of these limitations, only restricted use of
cartridge respirators is considered appropriate.
Cartridge performance is affected by humidity. Cartridges should be changed after 2 hr of continuous use unless it is determined that the humidity is less than
75%, in which case, cartridges can be used for 4 hr. Used cartridges should be discarded daily, regardless of the length of time used

8.2.3. Environmental exposure controls

See section 12

SECTION 9 Physical and chemical properties

9.1. Information on basic physical and chemical properties

Appearance Brown

Relative density (Water =

Physical state Liquid 0.990 - 1.005
1)

Partition coefficient n-
Odour Not Available Not Available
octanol / water
Auto-ignition temperature
Odour threshold Not Available >200
(°C)
Decomposition
pH (as supplied) Infinity Not Available
temperature (°C)
Melting point / freezing
Not Available Viscosity (cSt) Not Applicable
point (°C)
Initial boiling point and
150-230 Molecular weight (g/mol) Not Applicable
boiling range (°C)

Flash point (°C) Not Applicable Taste Not Available

Continued...
Part Number: 571604 (25L steel drums) Page 9 of 16 Issue Date: 29/05/2024
Version No: 13.42 Print Date: 26/07/2024
CARBON REMOVER

Evaporation rate Not Available BuAC = 1 Explosive properties Not Available

Flammability Not Applicable Oxidising properties Not Available
Surface Tension (dyn/cm
Upper Explosive Limit (%) Not Available Not Available
or mN/m)
Lower Explosive Limit (%) Not Applicable Volatile Component (%vol) Not Available
Vapour pressure (kPa) Not Applicable Gas group Not Available
Solubility in water Immiscible pH as a solution (5%) 10-11
Vapour density (Air = 1) Not Applicable VOC g/L Not Applicable
Nanoform Particle
Nanoform Solubility Not Available Not Available
Characteristics
Particle Size Not Available

9.2. Other information

Not Available

SECTION 10 Stability and reactivity

10.1.Reactivity See section 7.2

Unstable in the presence of incompatible materials.
10.2. Chemical stability Product is considered stable.
Hazardous polymerisation will not occur.
10.3. Possibility of
See section 7.2
hazardous reactions
10.4. Conditions to avoid See section 7.2
10.5. Incompatible
See section 7.2
materials
10.6. Hazardous
See section 5.3
decomposition products

SECTION 11 Toxicological information

11.1. Information on hazard classes as defined in Regulation (EC) No 1272/2008

Evidence shows, or practical experience predicts, that the material produces irritation of the respiratory system, in a substantial
number of individuals, following inhalation. In contrast to most organs, the lung is able to respond to a chemical insult by first
removing or neutralising the irritant and then repairing the damage. The repair process, which initially evolved to protect
mammalian lungs from foreign matter and antigens, may however, produce further lung damage resulting in the impairment of
Inhaled gas exchange, the primary function of the lungs. Respiratory tract irritation often results in an inflammatory response involving
the recruitment and activation of many cell types, mainly derived from the vascular system.

Inhalation of aerosols (mists, fumes), generated by the material during the course of normal handling, may be damaging to the
health of the individual.
Swallowing of the liquid may cause aspiration of vomit into the lungs with the risk of haemorrhaging, pulmonary oedema,
progressing to chemical pneumonitis; serious consequences may result.
Ingestion Signs and symptoms of chemical (aspiration) pneumonitis may include coughing, gasping, choking, burning of the mouth, difficult
breathing, and bluish coloured skin (cyanosis).
Accidental ingestion of the material may be damaging to the health of the individual.
The material is not thought to produce adverse health effects or skin irritation following contact (as classified by EC Directives
using animal models). Nevertheless, good hygiene practice requires that exposure be kept to a minimum and that suitable gloves
be used in an occupational setting.
Skin Contact
Open cuts, abraded or irritated skin should not be exposed to this material
Entry into the blood-stream through, for example, cuts, abrasions, puncture wounds or lesions, may produce systemic injury with
harmful effects. Examine the skin prior to the use of the material and ensure that any external damage is suitably protected.

Eye Although the liquid is not thought to be an irritant (as classified by EC Directives), direct contact with the eye may produce
transient discomfort characterised by tearing or conjunctival redness (as with windburn).
Long-term exposure to respiratory irritants may result in disease of the airways involving difficult breathing and related systemic
problems.
Chronic Limited evidence suggests that repeated or long-term occupational exposure may produce cumulative health effects involving
organs or biochemical systems.
Prolonged or repeated skin contact may cause drying with cracking, irritation and possible dermatitis following.

TOXICITY IRRITATION
CARBON REMOVER
Oral (Human)LC50: 150 mg/kg[2] Not Available

Continued...
Part Number: 571604 (25L steel drums) Page 10 of 16 Issue Date: 29/05/2024
Version No: 13.42 Print Date: 26/07/2024
CARBON REMOVER

TOXICITY IRRITATION

Oral (Rat) LD50: 4600 mg/kg[2] Eye : Mild

dichlorotoluene Eye: no adverse effect observed (not irritating)[1]

Skin : Moderate

Skin: adverse effect observed (irritating)[1]

TOXICITY IRRITATION

Hydrocarbons, C10-C13, n- Dermal (Other) LD50: >3400 mg/kg[2] Not Available

alkanes, isoalkanes,
cyclics, aromatics (2-25%)- Inhalation (Rat) LC50: 13,1 mg/kg[2]

Oral (Rat) LD50: >15000 mg/kg[2]

Hydrocarbones, C10, TOXICITY IRRITATION

aromatics, <1% naphtalene Not Available Not Available

TOXICITY IRRITATION

Oral (Rat) LD50: 608 mg/kg[2] Eye (rabbit): 726 ug - SEVERE

tar acids, 3,5-xylenol
fraction Eye: adverse effect observed (irreversible damage)[1]

Skin: adverse effect observed (corrosive)[1]

Legend: 1. Value obtained from Europe ECHA Registered Substances - Acute toxicity 2. Value obtained from manufacturer's SDS.
Unless otherwise specified data extracted from RTECS - Register of Toxic Effect of chemical Substances

For dichlorotoluenes:
2,6-Dichlorotoluene is moderately toxic in a repeated dose study (i.e. liver, kidney, thymus) and reproductive/ developmental
toxicity study (maternal toxicity).
Repeat dose toxicity: In a combined repeat dose and reproductive/developmental toxicity screening test, using 2,6-
dichlorotoluene both male and female rats showed histopathological changes in liver, kidney and thymus, and maternal toxicity
was observed. The no observed effect levels (NOEL) were obtained as 30 mg/kg/day for repeated dose toxicity and 100
mg/kg/day for reproductive toxicity.
dichlorotoluene In a combined repeat dose and reproductive/developmental toxicity screening test, using 2,4-dichlorotoluene, dose dependent
salivation was found in all treated groups. Toxicological significant changes in haematological and blood chemical examinations
were found at the highest dose (e.g. decrease of platelet count). Increased liver and kidney weights were also found at the same
level with pathological remarks (e.g. centrilobular swelling of hepatocytes). For reproductive/developmental end-points, a
decrease of fertility was found in conjunction with normal copulation but with low pregnancy at the highest dose. However, no
histopathological change related to infertility was seen in the paternal organs. Decreases of pup body weights were noted in the
highest dose group during the lactation period. No sensitising effects in guinea pig (OECD 406) GPMT according to Magnusson-
Kligman

tar acids, 3,5-xylenol The material may produce severe irritation to the eye causing pronounced inflammation. Repeated or prolonged exposure to
fraction irritants may produce conjunctivitis.
Tumorigenic by RTECS criteria
Asthma-like symptoms may continue for months or even years after exposure to the material ends. This may be due to a non-
allergic condition known as reactive airways dysfunction syndrome (RADS) which can occur after exposure to high levels of
highly irritating compound. Main criteria for diagnosing RADS include the absence of previous airways disease in a non-atopic
individual, with sudden onset of persistent asthma-like symptoms within minutes to hours of a documented exposure to the
CARBON REMOVER &
irritant. Other criteria for diagnosis of RADS include a reversible airflow pattern on lung function tests, moderate to severe
dichlorotoluene & tar
bronchial hyperreactivity on methacholine challenge testing, and the lack of minimal lymphocytic inflammation, without
acids, 3,5-xylenol fraction
eosinophilia. RADS (or asthma) following an irritating inhalation is an infrequent disorder with rates related to the concentration of
and duration of exposure to the irritating substance. On the other hand, industrial bronchitis is a disorder that occurs as a result
of exposure due to high concentrations of irritating substance (often particles) and is completely reversible after exposure
ceases. The disorder is characterized by difficulty breathing, cough and mucus production.

Acute Toxicity Carcinogenicity

Skin Irritation/Corrosion Reproductivity
Serious Eye
STOT - Single Exposure
Damage/Irritation
Respiratory or Skin
STOT - Repeated Exposure
sensitisation
Mutagenicity Aspiration Hazard

Legend: – Data either not available or does not fill the criteria for classification
– Data available to make classification

11.2 Information on other hazards

Continued...
Part Number: 571604 (25L steel drums) Page 11 of 16 Issue Date: 29/05/2024
Version No: 13.42 Print Date: 26/07/2024
CARBON REMOVER

11.2.1. Endocrine disrupting properties

No evidence of endocrine disrupting properties were found in the current literature.

11.2.2. Other information

See Section 11.1

SECTION 12 Ecological information

12.1. Toxicity

Endpoint Test Duration (hr) Species Value Source

CARBON REMOVER Not Not Not
Not Available Not Available
Available Available Available

Endpoint Test Duration (hr) Species Value Source

EC50 72h Algae or other aquatic plants 1.4mg/l 2

dichlorotoluene EC50 48h Crustacea 1mg/l 2

LC50 96h Fish 2mg/l 1
EC50(ECx) 24h Algae or other aquatic plants <0.001mg/L 2

Endpoint Test Duration (hr) Species Value Source

Hydrocarbons, C10-C13, n-
EC50 48 Crustacea Daphnia magna 100mg/L 8
alkanes, isoalkanes,
cyclics, aromatics (2-25%)- Fish Oncorhynchus mykiss (Rainbow 10-
LC50 96 8
trout) 100mg/L

Endpoint Test Duration (hr) Species Value Source

Hydrocarbones, C10,
Not Not Not
aromatics, <1% naphtalene Not Available Not Available
Available Available Available

Endpoint Test Duration (hr) Species Value Source

EC50 72h Algae or other aquatic plants 14mg/l 2

tar acids, 3,5-xylenol EC50 48h Crustacea 2.37mg/l 2

fraction EC50 96h Algae or other aquatic plants 100mg/l 2
NOEC(ECx) 96h Fish 0.3mg/l 2

LC50 96h Fish 4.4mg/l 2

Legend: Extracted from 1. IUCLID Toxicity Data 2. Europe ECHA Registered Substances - Ecotoxicological Information - Aquatic Toxicity
4. US EPA, Ecotox database - Aquatic Toxicity Data 5. ECETOC Aquatic Hazard Assessment Data 6. NITE (Japan) -
Bioconcentration Data 7. METI (Japan) - Bioconcentration Data 8. Vendor Data

Toxic to aquatic organisms, may cause long-term adverse effects in the aquatic environment.
Do NOT allow product to come in contact with surface waters or to intertidal areas below the mean high water mark. Do not contaminate water when cleaning
equipment or disposing of equipment wash-waters.
Wastes resulting from use of the product must be disposed of on site or at approved waste sites.
DO NOT discharge into sewer or waterways.

12.2. Persistence and degradability

Ingredient Persistence: Water/Soil Persistence: Air
No Data available for all ingredients No Data available for all ingredients

12.3. Bioaccumulative potential

Ingredient Bioaccumulation
No Data available for all ingredients

12.4. Mobility in soil

Ingredient Mobility
No Data available for all ingredients

12.5. Results of PBT and vPvB assessment

P B T
Relevant available data Not Available Not Available Not Available

Continued...
Part Number: 571604 (25L steel drums) Page 12 of 16 Issue Date: 29/05/2024
Version No: 13.42 Print Date: 26/07/2024
CARBON REMOVER

P B T

PBT
vPvB

PBT Criteria fulfilled? No

vPvB No

12.6. Endocrine disrupting properties

No evidence of endocrine disrupting properties were found in the current literature.

12.7. Other adverse effects

No evidence of ozone depleting properties were found in the current literature.

SECTION 13 Disposal considerations

13.1. Waste treatment methods

Legislation addressing waste disposal requirements may differ by country, state and/ or territory. Each user must refer to laws
operating in their area. In some areas, certain wastes must be tracked.
A Hierarchy of Controls seems to be common - the user should investigate:
Reduction
Reuse
Recycling
Disposal (if all else fails)
This material may be recycled if unused, or if it has not been contaminated so as to make it unsuitable for its intended use. If it
has been contaminated, it may be possible to reclaim the product by filtration, distillation or some other means. Shelf life
Product / Packaging
considerations should also be applied in making decisions of this type. Note that properties of a material may change in use, and
disposal
recycling or reuse may not always be appropriate.
DO NOT allow wash water from cleaning or process equipment to enter drains.
It may be necessary to collect all wash water for treatment before disposal.
In all cases disposal to sewer may be subject to local laws and regulations and these should be considered first.
Where in doubt contact the responsible authority.
Recycle wherever possible or consult manufacturer for recycling options.
Consult State Land Waste Authority for disposal.
Bury or incinerate residue at an approved site.
Recycle containers if possible, or dispose of in an authorised landfill.

Waste treatment options Not Available

Sewage disposal options Not Available

SECTION 14 Transport information

Labels Required

Marine Pollutant

Land transport (ADR-RID)

14.1. UN number or ID
2810
number
14.2. UN proper shipping
TOXIC LIQUID, ORGANIC, N.O.S. (Xylenol, Dichlorotoluene mixture)
name

14.3. Transport hazard Class 6.1

class(es) Subsidiary Hazard Not Applicable

14.4. Packing group III

14.5. Environmental
Environmentally hazardous
hazard

14.6. Special precautions

Hazard identification (Kemler) 60
for user

Continued...
Part Number: 571604 (25L steel drums) Page 13 of 16 Issue Date: 29/05/2024
Version No: 13.42 Print Date: 26/07/2024
CARBON REMOVER

Classification code T1

Hazard Label 6.1

Special provisions 274 614

Limited quantity 5L
Tunnel Restriction Code E

Air transport (ICAO-IATA / DGR)

14.1. UN number 2810

14.2. UN proper shipping

Toxic liquid, organic, n.o.s. * (Xylenol, Dichlorotoluene mixture)
name

ICAO/IATA Class 6.1

14.3. Transport hazard
ICAO / IATA Subsidiary Hazard Not Applicable
class(es)
ERG Code 6L

14.4. Packing group III

14.5. Environmental
Environmentally hazardous
hazard

Special provisions A3 A4 A137

Cargo Only Packing Instructions 663

Cargo Only Maximum Qty / Pack 220 L
14.6. Special precautions
Passenger and Cargo Packing Instructions 655
for user
Passenger and Cargo Maximum Qty / Pack 60 L

Passenger and Cargo Limited Quantity Packing Instructions Y642

Passenger and Cargo Limited Maximum Qty / Pack 2L

Sea transport (IMDG-Code / GGVSee)

14.1. UN number 2810
14.2. UN proper shipping
TOXIC LIQUID, ORGANIC, N.O.S. (Xylenol, Dichlorotoluene mixture)
name

14.3. Transport hazard IMDG Class 6.1

class(es) IMDG Subsidiary Hazard Not Applicable

14.4. Packing group III

14.5 Environmental hazard Marine Pollutant

EMS Number F-A , S-A

14.6. Special precautions
Special provisions 223 274
for user
Limited Quantities 5L

Inland waterways transport (ADN)

14.1. UN number 2810

14.2. UN proper shipping

TOXIC LIQUID, ORGANIC, N.O.S. (Xylenol, Dichlorotoluene mixture)
name
14.3. Transport hazard
6.1 Not Applicable
class(es)

14.4. Packing group III

14.5. Environmental
Environmentally hazardous
hazard

Classification code T1
Special provisions 274; 614; 802
14.6. Special precautions
Limited quantity 5L
for user
Equipment required PP, EP, TOX, A

Fire cones number 0

14.7. Maritime transport in bulk according to IMO instruments

Continued...
Part Number: 571604 (25L steel drums) Page 14 of 16 Issue Date: 29/05/2024
Version No: 13.42 Print Date: 26/07/2024
CARBON REMOVER

14.7.1. Transport in bulk according to Annex II of MARPOL and the IBC code
Not Applicable

14.7.2. Transport in bulk in accordance with MARPOL Annex V and the IMSBC Code
Product name Group

dichlorotoluene Not Available

Hydrocarbons, C10-C13, n-
alkanes, isoalkanes, cyclics, Not Available
aromatics (2-25%)-
Hydrocarbones, C10,
Not Available
aromatics, <1% naphtalene

tar acids, 3,5-xylenol fraction Not Available

14.7.3. Transport in bulk in accordance with the IGC Code

Product name Ship Type

dichlorotoluene Not Available

Hydrocarbons, C10-C13, n-
alkanes, isoalkanes, cyclics, Not Available
aromatics (2-25%)-
Hydrocarbones, C10,
Not Available
aromatics, <1% naphtalene

tar acids, 3,5-xylenol fraction Not Available

SECTION 15 Regulatory information

15.1. Safety, health and environmental regulations / legislation specific for the substance or mixture

dichlorotoluene is found on the following regulatory lists

Europe EC Inventory
European Union - European Inventory of Existing Commercial Chemical Substances (EINECS)

Hydrocarbons, C10-C13, n-alkanes, isoalkanes, cyclics, aromatics (2-25%)- is found on the following regulatory lists

Not Applicable

Hydrocarbones, C10, aromatics, <1% naphtalene is found on the following regulatory lists

Not Applicable

tar acids, 3,5-xylenol fraction is found on the following regulatory lists

Chemical Footprint Project - Chemicals of High Concern List

EU REACH Regulation (EC) No 1907/2006 - Annex XVII - Restrictions on the manufacture, placing on the market and use of certain dangerous substances,
mixtures and articles
EU REACH Regulation (EC) No 1907/2006 - Annex XVII (Appendix 2) Carcinogens: Category 1 B
EU REACH Regulation (EC) No 1907/2006 - Annex XVII (Appendix 4) Germ cell mutagens: Category 1 B
Europe EC Inventory
European Union - European Inventory of Existing Commercial Chemical Substances (EINECS)
European Union (EU) Regulation (EC) No 1272/2008 on Classification, Labelling and Packaging of Substances and Mixtures - Annex VI

Additional Regulatory Information

Not Applicable

This safety data sheet is in compliance with the following EU legislation and its adaptations - as far as applicable - : Directives 98/24/EC, - 92/85/EEC, - 94/33/EC,
- 2008/98/EC, - 2010/75/EU; Commission Regulation (EU) 2020/878; Regulation (EC) No 1272/2008 as updated through ATPs.

Information according to 2012/18/EU (Seveso III):

Seveso Category E2

15.2. Chemical safety assessment

No Chemical Safety Assessment has been carried out for this substance/mixture by the supplier.

National Inventory Status

Continued...
Part Number: 571604 (25L steel drums) Page 15 of 16 Issue Date: 29/05/2024
Version No: 13.42 Print Date: 26/07/2024
CARBON REMOVER

National Inventory Status

Australia - AIIC / Australia

No (tar acids, 3,5-xylenol fraction)
Non-Industrial Use

Canada - DSL No (dichlorotoluene; tar acids, 3,5-xylenol fraction)

Canada - NDSL No (tar acids, 3,5-xylenol fraction)

China - IECSC Yes

Europe - EINEC / ELINCS /

Yes
NLP

Japan - ENCS No (tar acids, 3,5-xylenol fraction)

Korea - KECI No (dichlorotoluene; tar acids, 3,5-xylenol fraction)

New Zealand - NZIoC No (tar acids, 3,5-xylenol fraction)

Philippines - PICCS No (tar acids, 3,5-xylenol fraction)

USA - TSCA No (tar acids, 3,5-xylenol fraction)

Taiwan - TCSI No (tar acids, 3,5-xylenol fraction)

Mexico - INSQ No (tar acids, 3,5-xylenol fraction)

Vietnam - NCI No (tar acids, 3,5-xylenol fraction)

Russia - FBEPH Yes

Yes = All CAS declared ingredients are on the inventory

Legend: No = One or more of the CAS listed ingredients are not on the inventory. These ingredients may be exempt or will require
registration.

SECTION 16 Other information

Revision Date 29/05/2024

Initial Date 09/04/2018

CONTACT POINT
- For quotations contact your local Customer Services - http://wssdirectory.wilhelmsen.com/#/customerservices - - Responsible for safety data sheet Wilhelmsen
Ships Service AS - Prepared by: Compliance Manager, - Email: Email: [email protected] - Telephone: Tel.: +47 67584000

Full text Risk and Hazard codes

H315 Causes skin irritation.
H318 Causes serious eye damage.

H410 Very toxic to aquatic life with long lasting effects.

H412 Harmful to aquatic life with long lasting effects.

SDS Version Summary

Date of
Version Sections Updated
Update
Hazards identification - Classification, Firefighting measures - Fire Fighter (fire/explosion hazard), Composition
12.42 29/05/2024
/ information on ingredients - Ingredients

Other information
Classification of the preparation and its individual components has drawn on official and authoritative sources as well as independent review by the Chemwatch
Classification committee using available literature references.

The SDS is a Hazard Communication tool and should be used to assist in the Risk Assessment. Many factors determine whether the reported Hazards are Risks
in the workplace or other settings. Risks may be determined by reference to Exposures Scenarios. Scale of use, frequency of use and current or available
engineering controls must be considered.

For detailed advice on Personal Protective Equipment, refer to the following EU CEN Standards:
EN 166 Personal eye-protection
EN 340 Protective clothing
EN 374 Protective gloves against chemicals and micro-organisms
EN 13832 Footwear protecting against chemicals
EN 133 Respiratory protective devices

Definitions and abbreviations

PC－TWA: Permissible Concentration-Time Weighted Average
PC－STEL: Permissible Concentration-Short Term Exposure Limit
IARC: International Agency for Research on Cancer
ACGIH: American Conference of Governmental Industrial Hygienists

Continued...
Part Number: 571604 (25L steel drums) Page 16 of 16 Issue Date: 29/05/2024
Version No: 13.42 Print Date: 26/07/2024
CARBON REMOVER

STEL: Short Term Exposure Limit

TEEL: Temporary Emergency Exposure Limit。
IDLH: Immediately Dangerous to Life or Health Concentrations
ES: Exposure Standard
OSF: Odour Safety Factor
NOAEL: No Observed Adverse Effect Level
LOAEL: Lowest Observed Adverse Effect Level
TLV: Threshold Limit Value
LOD: Limit Of Detection
OTV: Odour Threshold Value
BCF: BioConcentration Factors
BEI: Biological Exposure Index
DNEL: Derived No-Effect Level
PNEC: Predicted no-effect concentration

AIIC: Australian Inventory of Industrial Chemicals

DSL: Domestic Substances List
NDSL: Non-Domestic Substances List
IECSC: Inventory of Existing Chemical Substance in China
EINECS: European INventory of Existing Commercial chemical Substances
ELINCS: European List of Notified Chemical Substances
NLP: No-Longer Polymers
ENCS: Existing and New Chemical Substances Inventory
KECI: Korea Existing Chemicals Inventory
NZIoC: New Zealand Inventory of Chemicals
PICCS: Philippine Inventory of Chemicals and Chemical Substances
TSCA: Toxic Substances Control Act
TCSI: Taiwan Chemical Substance Inventory
INSQ: Inventario Nacional de Sustancias Químicas
NCI: National Chemical Inventory
FBEPH: Russian Register of Potentially Hazardous Chemical and Biological Substances

Classification and procedure used to derive the classification for mixtures according to Regulation (EC) 1272/2008 [CLP]
Classification according to
regulation (EC) No
Classification Procedure
1272/2008 [CLP] and
amendments

Acute Toxicity (Oral)

Expert judgement
Category 3, H301
Aspiration Hazard Category
Calculation method
1, H304

Acute Toxicity (Dermal)

Expert judgement
Category 3, H311

Skin Corrosion/Irritation
Expert judgement
Category 1C, H314
Sensitisation (Skin) Category
Expert judgement
1, H317

Specific Target Organ

Toxicity - Single Exposure
Expert judgement
(Narcotic Effects) Category
3, H336
Specific Target Organ
Toxicity - Repeated Expert judgement
Exposure Category 1, H372
Hazardous to the Aquatic
Environment Long-Term Calculation method
Hazard Category 2, H411

Powered by AuthorITe, from Chemwatch.

end of SDS