Leading Technology Partners.....

A SAIT GROUP COMPANY

Cathodic Protection, Anti Fouling, AC Mitigation, Corrosion Engineering, Gas Flow Measurement & Regulation,
Construction & Manufacturing, Pipeline Information Management System, Leak Detection, Coatings & Field Joints,
Insulation Joints,Wireless Remote Monitoring Systems, Well Head Monitoring System, Downhole Monitoring System,
Pumping Solutions, High Voltage Cables , Composite Repair Materials, Electric Heat Tracer.....
www.bsstechnologies.com
1119R11
 Your True Partner for Asset Integrity Management

A SAIT GROUP COMPANY

1119R11
SAIT GROUP OF COMPANIES www.bsstechnologies.com
SAIT GROUP, one of the world class group companies and pioneers in the middle east specialized in Cathodic Protection and Corrosion Engineering. Since
inception, it has become the leading solution providers in MENA and Asia Pacific. Over the last 20 years, the group has developed a highly resourced, responsive global
company with strategically positioned offices and facilities in Abu Dhabi, Dubai, Saudi Arabia, Kuwait, India, Malaysia, Nigeria, Canda. The group has its state of art manufacturing
units in Dubai, Malaysia & India. The Production facilitiy operates with state of the art technologies and equipment with the layout to address the quality, safety and environment
requirements. With over 300 employees worldwide, we are committed to customer satisfaction through continuous training, research & development and improvement of our qualified trained
technical and non-technical staff.

IN LAST TEN YEARS GROUP HAS FOCUSED IN DIVERSIFYING BY PARTNERING WITH LEADING INTERNATIONAL COMPANIES WHO HAS THE CAPABILITIES IN PROVIDING PRODUCTS AND
SERVICES IN RELATED INDUSTRIES SERVING ASSET MANAGEMENT AND ASSET INTEGRITY AND OTHER RELATED SERVICES TO STRENGTHEN THE SUPPLY CHAIN.

WE ARE “ONE STOP CONSULTING / ENGINEERING / MATERIAL / EQUIPMENT PROVIDERS AND CONTRACTORS FOR THE WIDE VARIETY OF REQUIREMENTS IN INTEGRITY MANAGEMENT IN THE
OIL, GAS, WATER, ENERGY, TRANSPORT AND INFRASTRUCTURE SECTOR.”

BSS Technologies, the backbone of SAIT Group is based out of Abu Dhabi with capabilities in Cathodic Protection and Corrosion Engineering, it has developed own subsidiaries in manufacturing and has
capabilities in surveys, engineering, R & D, installation, construction and maintenance.

Bin Sari Metal Casting, our manufacturing unit specialized in the manufacturing of Sacrificial Anodes, Transformer Rectifier Units, Remote Monitoring and Control systems, is located at National Industries Park,
Jebel Ali – Dubai. We do keep stock of all major materials required in the field of Cathodic Protection and Corrosion Engineering. Major supply includes Transformer Rectifiers, Solar Power Systems, Sacrificial
Anodes, Impressed Current Anodes, RMCS, Cables, Test Stations, Junction Boxes, Corrosion Coupons, Corrosion Monitoring probes, Backfill materials..etc

SSEC, Sait Specialized Engineering and Contracting is based in Abu Dhabi and serving the industry with their expertise in Electro Mechanical and Civil contracting. The primary objective which paved the birth of
this organization was to cater the inhouse business subcontract activities of Sait group of Companies. Gradually it became an independent organization encouraged by the opportunities outside the group business.
The diversity of our project experience enables us to match our services closely to the needs of each of our clients. This organization created inhouse capability in installation of CP system.

RACE Tech, is the RESEARCH & DEVELOPMENT division of BSS Technologies located at Mumbai - India. It is SAIT Group management’s special interest that a good percentage of our annual profit is wisely
invested in the areas of Researches in Electronics and Softwares in developing new products. These are spent either directly in our facilities or in close co-operation with our raw material supplier’s facilities. A wide
variety of designs are developed inhouse and selected to customer satisfaction, strictly inaccordance with the quality standards, environmental conditions and material standards. New technologies are selected
with thorough knowledge and fully understanding the properties and behavior of the products

KAZ , the Division of SAIT Group established in the Kingdom of Saudi Arabia to cater to specialized Engineering Services of Sait Group in the Saudi Region. It also has a manufacturing facilitiy in Jubail. Apart
from offering specialized Cathodic Protection and Corrosion Engineering services, it also act as a satellite office of all the subsidiaries of SAIT Group and promote all capabilities of the group in its region.

SSE Technologies, Sait Specialized Engineering Technologies Kuwait W.L.L is an independent arm of SAIT Group, to cater to the ever increasing corrosion control needs of the Oil & Gas, Electricity, Water, Marine
& Construction industry in Kuwait. Apart from offering specialized Cathodic Protection and Corrosion Engineering services, it also act as a satellite office of all the subsidiaries of SAIT Group and promote all
capabilities of the group in its region.

BSS Technologies CP (INTL) SDN. BHD, Malaysian Manufacturing and Services Hub for Malaysia, Indonesia, Singapore, Australia. Apart from offering specialized Cathodic Protection and Corrosion
Engineering services, it also act as a satellite office of all the subsidiaries of SAIT Group and promote all capabilities of the group in its region.

BSS Tech CP (I) PVT LTD will handle as a dedicated team, the increasing demand in India in the field of Cathodic Protection & Corrosion Engineering. Apart from offering specialized Cathodic Protection and Corrosion
Engineering services, it also act as a satellite office of all the subsidiaries of SAIT Group and promote all capabilities of the group in its region.

Sait Group of Companies

CP (I) PVT LTD CP (INTL) SDN. BHD NIGERIA

Malaysian Manufacturing
and Services Hub for
Malaysia, Indonesia,
Singapore, Australia..
1119R11
 INTRODUCTION TO BSS TECHNOLOGIES

BSS Technologies core competency is in the field of Corrosion Engineering and Cathodic Protection. Since
Message From the Management inception, we have consistently followed a growth path owing to our philosophy of High-Tech Engineering

BSS Technologies is privileged to be the pioneers Technologies with constant product innovation and upgradation.
in the corrosion engineering and cathodic protec-
Our primary focus has been on Customer Delight - brought about, by a rich task force of qualified, committed and
tion industry in the Middle East with our skilled
personnel and Research & Development Depart- experienced professionals to cater to the changing needs of the industry.
ment.
To meet our Customer requirements - we have placed our Corporate Office in Abu Dhabi- UAE. In order to provide reliable
products expediently to our customers, we hold our Head Office, Engineering and Manufacturing Facilities in National Industries
Park, Jebel Ali, Dubai, UAE. This facility has Transformer Rectifier production, RMCS manufacturing, Anode casting and all
customisation capabilities. These Production Facilities operate with state of the art Technologies & Equipment and have the layout
to address the Quality, Safety and Environmental Requirements.

Our ISO -9001:2015 certification affirms our highest commitment to our motto that “The key to Customer Delight is quality”

As years passed by, we diversified our business in to other fields of Asset Integrity & Value Engineering including Leak Detection
Systems, Coatings and Tapes, Pipeline Information Management Solutions (PIMS) maintaining our consistent and reliable
expertise for services in Cathodic Protection and Corrosion Engineering. We are now a “ One Stop destination for Consulting /
Engineering / Material / Equipment Providers and Contractors for the wide variety of requirements in Integrity Management in
the Oil, Gas, Water, Energy, Transport and Infrastructure Sector.”

PROFILE

BSS Tech - as a pioneer company specialized in the areas of Cathodic Protection & Corrosion Control - is a technology driven, customer
oriented company. We maintain a team of qualified Engineers and Technicians with ample site experience in different countries and
environments - headed by NACE CP Specialists. BSS Tech offers full range of Engineering Services, Instruments and Products related
to Corrosion Engineering, Cathodic Protection, AC mitigation, Anti Fouling, apart from the core corrosion protection we also provide PIMS,
Leak Detection System, Pipeline Coating & Steel Joint Coatings, Wireless Remote Monitoring Systems to the Industry in accordance with
international standards. BSS Tech is a 100% self reliant organization with complete Engineering, Material and Execution capabilities with
a separate Team for Surveys and Studies.

QUALITY POLICY

BSS Tech’s Management Team is committed to establish, document, implement and practice a scalable Quality Management System to
effectively manage Global Business Operations. Quality Performance is a commitment to excellence by BSS Tech employee and
achieves it by teamwork and process of continuous improvement. We are dedicated to become the leaders in delivering quality
products and services which meets or exceeds the expectations of our valued Customers. The Quality Management System gives the
Organization a focal point for promoting best practices and continuous improvement in accordance with BSS Tech’s Quality Policy.

www.bsstechnologies.com
1119R11
 TRANSFORMER RECTIFIER

Application
TRANSFORMER RECTIFIER
The Key to any impressed Current Cathodic Protection System is an efficient and reliable Power Unit that can provide
an uninterrupted Direct Power Supply for the Anode Energization. BSS Tech offers a fully comprehensive range of
Transformer Rectifiers including ATEX certified units.
We manufacture all types, all sized, standard, customized Transformer Rectifiers. We also manufacture explosion proof units
with ATEX certification.
Our Cathodic Protection Engineers are available to advice the most efficient & economical Transformer Rectifier units for any
specific application.
How to Order
To help our clients to pick the best features in a Transformer Rectifier unit, BSS Tech had developed an easy procedure. Pick the
features from the following. A sample order can be explained as below:

BSTR-48-100-A-1-A-A-O-S-BIS The Order Code is supplied with the below reference:

SAMPLE CODE BS TR 48 100 A 1 A A O S BIS

REFERENCE 1 2 3 4 5 6 7 8 9 10 11
Reference Detail:
1) BS 6) Input Power Frequency : 10) Enclosure Type:
2) TR 1) 50 Hz H - Hazardous Area Use

3) DC volt* 2) 60 Hz I - Safe Area Indoor

S - Safe Area Outdoor
4) DC amp* 7) Mode of Operation:
X - ATEX certified Air Cooled
5) AC Input: A - Auto
11) Special Features: Oil Immersed
A - 415V, 3Ph B - Manual
T - Timer
Explosion Proof
B - 400V, 3Ph 8) Type of Control: F - DC Fuse Alarm
Special Purpose
C - 115/240V, 1Ph V - Variac Control O - 115V Outle
Custom Design
D - 240/460, 1Ph T - Tyristor Control B - Breather
D - Dual Inlet ATEX certified
E - 240/260, 3Ph A - Tap Changer
I - Current Interrrupter
F - 240V, 1Ph 9) Cooling:
S - Surge Arrester Standard Rating TR units
G - 115/480, 1Ph O - Oil Cooled
R - Remote Control
H - 120 V ,1Ph A - Air Cooled 10V, 10A 20V, 15A 20V, 20A 25V, 15A 25V, 25A
M - Multi-Channel* 25V, 50A 50V, 50A 50V, 75A 75V, 75A 100V, 100A
E - Oil Immersed Explosion Proof N - Remote Monitoring
A - Auto Change over

* For Multi-Channel Transformers, Reference No. 3 & 4 shall be indicated as V & I repectively. The details of the channel
voltage & Current shall be provided seperately while ordering the Transformer Rectifier. www.bsstechnologies.com
1119R11
 REMOTE MONITORING & CONTROL SYSTEM
REMOTE MONITORING & CONTROL SYSTEM
Application
The Remote Monitoring and Control System (RMCS) is designed to monitor and control Impressed Current
Cathodic Protection System Remotely. RMCS helps you to accomplish complete control of the Cathodic Protection
operation in a plant, in desert or in deep sea. Features RMCS consists of it’s own power supply units, software,
communication and hardware for control monitoring & data logging. The site based equipment has local data logging facility
which works on the embedded software and instructs the logic for monitoring and / or control. Power supply unit and the rest
of the hardwares are placed in an instrument box or in a cabinet . The inbuilt hardware controls power supply output,
communicate with remote PC in control room through radio communication which has zero operation/service charges by any third
party. The software in Remote Computer communicates with RTU for Control, Monitoring and Data logging. It provides access to all
functions of the RTU and a user-friendly interface with graphics. Major Monitoring and Controls available with RMCS are :
Auto Reference Mode Environmental Conditions Electrical Interface
Ambient Temp -10˚C to 60˚C Input Voltage 230VAC
Your eyes to Interruption Cycle
Storage Temp -10˚C to 60˚C Surge Protection Yes
Site Programming
Cathodic Protection System Humidity 5 to 95% Circuit Protection Optical Isolation
Alarms and call back
Size Customized
Communication Interface **
Data Recording
Communication Protocol Standard Modbus RTU
Analytical Data Interpretation
Wireless Yes
Graphical Report Generator
Frequency 2.4 GHz
HARDWARE Real Time Monitoring Optical Interfacing Yes
CP RMU can be integrated with any existing CP power Reference Potential Monitoring & Control TCP/IP Yes
supply to collect and deliver the prescribed parameters to Reference, DC Voltage, DC Current monitoring and control Ethernet Topology Yes
the base .CP RMU can be used as a replacement to any test GSM Yes
SMS based alert system
station.
** All other modes of communication like RS485, fibre optic and radio are available. Requirement used to be specified.

Real Time Voltage, Current, Reference Monitoring Report Generator & Data Recording

www.bsstechnologies.com
1119R11
 SAIT TM - CPDM

The application named – “SAIT™- CPDM” is GEI enabled CP infrastructure life cycle monitoring. Database
SAITTM - CPDM
application software is developed with Java Virtual machine, Data Server and Application server. The primary aspect Software for Asset Integrity Techniques
of this software is to collect, store, safeguard the cathodic protection data and its asset details and provide custom made - CP DATA MANAGER
reports to evaluate the protection of various assets. The software provides unique facility to customize and store the entire
cathodic protection components and structures. The software is compatible with all Windows platform. The Software is
available as ‘Single User’, ‘Server Based’ and ‘Web Based’ - which makes ‘SAIT-CPDM’ the most flexible CP Data
management software catering the needs of various industries from an individual user to multiple users in big operating
industry. The key feature of this software is the GIS Viewer, which allows the user to view the respective locations of all their
installation and CP Components.
GIS facilitate application in:
 Monitoring assets conditions to assist in infrastructure life cycle planning and replacement.
 Field crews can capture inspection information and quickly update centrally stored as-built in data.
 Engineers can monitor cathodic protection systems to view information in relation to the distribution system, diagnose problems,
and ensure corrosion protection.
System Overview:
 The system involves developing a "WEB Desktop GIS*" based system by incorporating geographical database with real pipeline data
consisting of rail/road/foreign pipeline crossings, CP locations, valve locations, etc. with facility of user-friendly retrieval of information.
Key functionality allows the user to:
 100% Compatible with any structure or Installations.
 100% Customizable to any kind of CP Systems
 Historic data collection & analysis ; GIS Compatibility
 Map showing actual location of all structures and CP Components
 Back up & Restore feature; Expandable to any number of fields
 High Security

*WEB Desktop GIS - A web desktop or webtop is a desktop environment embedded in a web browser or similar client application. A webtop integrates
web applications, web services, and applications on the local client into a desktop environment using the desktop metaphor.
Features & Benefits
Features Benefits
An indispensable tool for
Flexible data entry and adhoc reporting Search, sort, and analyze data quickly
Year-to-year comparisons of various CP segments Easy visualization of problem areas with graphical reports
Cathodic Protection professionals
Manage large quantities of data on asset types and other related See problem areas for test stations, rectifiers, galvanic anodes,  Manages multiple facility types and surveys
maintenance information foreign bonds, isolated services, tank performance, and  Schedules routine field data collection
hundreds of pipeline assets  Judges system effectiveness
 Pinpoints problems
User-configured hierarchical tree for organization and editing Advanced organization and efficient editing for workflow
 Prepares operators for regulatory audits
Multi-user design for replication and synchronization Share critical data throughout an organization
Comparative line graphs, individual test point, rectifier and bond Analyze distribution and transmission lines
graphs, and continuous strip charts
Backup databas Restore database
www.bsstechnologies.com
1119R11
 TEST STATION - CAPTAIN

Information

BSS Tech introduces an innovative, economical and versatile solution for Cathodic Monitoring on Buried Metallic
C P MONITORING SYSTEM Structures, CAPTAIN – Cathodic Protection Test Stations have been specially developed for Monitoring of Cathodic
Protection Systems.

CAPTAIN is a High Impact Resistant , Non Conductive , above Ground Terminal for conveniently Monitoring Electrical
Currents & Potentials associated with all type of Cathodically Protected Structures.

CAPTAIN can be used as Monitoring Stations as well as Junction Boxes. Major applications are as listed below:

1) Underground Structure Potential Monitoring as a Test Station

2) Junction Box for Anodes; especially for Sacrificial Anodes

3) Reference Electrode Junction Box

4) Pipeline Bonding Stations for Crossing & Parallelism

5) Grounding System Termination

Technical Features
Test Station - Captain
1) Produced from High Impact Polycarbonate ; One of the World’s toughest Plastic which is used in making
Aircraft Windows, all kind of helmets from Military to Sports to Crash Helmets, etc.

2) Has 4 times the Impact strength of Aluminium with one half its weight.

3) Maintains Dimensional & Electrical stability in Temperature range from -60ºF to +250ºF.

4) Remains Stable under Ultra Violet Rays.

5) Terminals completely accessible from both side of Terminal Board.

6) Polycarbonate being Non Metallic & extremely resistant, reduces Electrical Shock Hazards drastically.

7) Available in wide range of colours to suit User Preferences.

Materials used
Test Station: Polycarbonate
Hardware: Machined Screws, Washers & Hex Nuts
(All Stainless Steel)
Conduit (Optional): Ultra Violet Stabilized

Each Test Station consists of a Cover, a Terminal Board with Integral Compression - Fit Base & a Compression Nut
for Clamping the Base to the Conduit & other Accessories.
www.bsstechnologies.com
1119R11
 SACRIFICIAL ALUMINIUM ANODE

Information SACRIFICIAL ALUMINIUM ANODE

Aluminium Anodes are usually applied in Water, Sea Water or Produced Brines. Standard Aluminium Anodes are
supplied in variety of Sizes and Weights. Prolonged exposure above 1220F will result in excessive Consumption of
Anode Material.
Aluminium Alloys Aluminium Platform / Jetties Anodes
DNV RP
Elements Mil –A-24779 GALVALUM III
B401
Silicon 0.08 – 0.20 0.12 max 0.08 – 0.20
Iron 0.09 max 0.09 max 0.13 max
Zinc 4.0 – 6.5 2.5 – 5.75 2-6
Indium 0.014 -0.020 0.015 – 0.040 0.01 – 0.02
Copper 0.004 max 0.003 max 0.006 max
Others(each) 0.02 max 0.02 max 0.02 max
Aluminium Remainder Remainder Remainder Weld on - Single Strap

Weld on - Tear Drop

Anode Anode Dimensions(mm) Core Dimensions(mm) Weight (kg) Aluminium Anode
Type(New) Length Width Height Length Width Height Net wt. Gross Wt.
Anode Anode Dimensions(mm) Core Dimensions(mm) Weight (kg) BTA035W 200 95 33 300 25 5 1.2 1.6
Type(New) Length Width Height Length Width Height Net wt. Gross Wt. BTA048W 290 90 40 440 30 5 1.7 2.2
BTA005T 120 40 25 200 10 3 0.2 0.25 BTA055W 300 90 40 400 25 5 2.1 2.5
BTA011T 180 60 32 260 20 3 0.4 0.5 BTA095W 340 155 35 450 38 5 3.7 4.3
BTA020T 220 75 38 300 20 3 0.8 0.9 BTA106W 400 150 33 540 40 5 4 4.8
BTA031T 200 95 30 300 20 3 1.2 1.4 BTA148W 440 105 60 560 30 5 6 6.7
BTA202W 550 130 50 680 50 5 8 9.1
Weld on - Double Strap
BTA224W 550 130 50 650 40 8 8.4 10.1
Anode Anode Dimensions(mm) Core Dimensions(mm) Weight (kg) BTA246W 550 135 58 680 50 5 10 11.1
Type Length Width Height Length Width Height Net wt. Gross Wt. BTA302W 550 130 75 680 50 5 12.5 13.6
BTA100D 305 152 36 254 32 5 3.8 4.5 BTA324W 920 130 50 1075 50 5 13 14.6
BTA177D 305 152 64 254 32 5 7.4 8 BTA437W 920 130 65 1075 50 5 18 19.7
BTA322D 460 230 51 430 32 6 13.5 14.5 BTA444W
BTA504W
920
920
160
130
60
75
1020
1075
40
50
8
5
17.4
21
20
22.7
Bracelet Anode
Bolt on Type
Plate Plate Net Gross
Anode Type Length(mm) Width(mm) Height(mm) C-C(mm) Width(mm) Thickness(mm) Wt.(Kg) Wt.(Kg)
BTA040B 200 100 30 110 50 5 1.4 1.8
BTA046B 200 100 40 110 50 5 1.7 2.1 Tear Drop Anodes
BTA071B 300 150 25 160 75 5 2.8 3.2
BTA082B 300 150 30 160 75 5 3.3 3.7 Stand OFF Anodes
BTA113B 300 150 40 160 75 5 4.7 5.1
BTA128B 300 150 50 160 75 5 5.4 5.8
Tank Anodes
BTA133B 300 200 40 160 100 5 5.6 6
Hull Anodes
BTA237B 300 200 65 160 100 5 10.3 10.7
BTA297B 400 180 70 180 80 5 13.1 13.4 Bracelet Anodes
BTA344B 540 200 65 340 100 5 15.1 15.5

Electrochemical Properties :
Solution Potential: -1.1V w.r.t Ag/AgCl Capacity: 2500 Ah/kg (min) Density: 2750 kg/m3

Customized Alloy, Dimensions and shape can be produced against order www.bsstechnologies.com
1119R11
 SACRIFICIAL MAGNESIUM ANODE
Information
Magnesium Anodes are applied in high resistivity like soil, potable water etc. Standard Magnesium Anodes are availa-
ble in variety of sizes and weight.
SACRIFICIAL ANODE High Potential Magnesium Anodes
FEATURES : Produces high driving voltage compared to other Galvanic Anode.
APPLICATIONS : At high resistivity or high current requirement. Buried Structures in soil of high resistivity such as
pipe lines, Storage Tanks etc in soil.
Standard Magnesium Anodes
FEATURES : Produces low driving voltage compared to high potential type.
APPLICATIONS : This type of Anode is useful when the current requirement of the system is less.
Extruded Magnesium Anodes
FEATURES: Influences larger structure surface uniformly produces greater amount of current than Cast Anodes.
APPLICATIONS : Structures buried or submerged in comparatively high resistivity electrolytes.
CHEMICAL COMPOSITION(%) Fe Other Imp(max)
Si Cu Ni
Product Mg Al Zn Mn Max Max Max Max Each Total
HM Balance 0.01 max - 0.5-1.3 0.05 0.002 0.001 0.03 0.05 0.3
Magnesium Anode SM Balance 5.3-6.7 2.5 -3.5 0.15-0.7 0.10 0.002 0.002 0.003 - 0.3
EM Balance 0.01 max - 0.5-1.3 - 0.002 0.001 0.03 - 0.3
ELECTRO CHEMICAL PROPERTIES
Open-Circuit Volt Closed-Circuit Volt Actual capacity at 50% efficiency Current
(-v respect to Cu/CuSO4) (-v respect to Cu/CuSO4) (Ahr/Kg) Efficiency(%)
HM 1.7 - 1.77 1.59 - 1.63 1105 min >50
SM 1.57 - 1.62 1.52 - 1.57 1115 min >50
EM 1.7 - 1.77 1.59 - 1.63 1105 min >50
DIMENSIONAL& WEIGHT TABLE
HIGH POTENTIONAL MAGNESIUM ANODE EXTRUDED MAGNESIUM ANODE
Anode Dimensions
Model No. Weight
(Kg) L A D H W Section 3/8x3/4+0.015
mm (± 25) mm (± 50) mm (± 50) mm (± 10) mm (± 10)
(Inch)
Bare Anode BTMG30H 1.4 114 165 152 76 76
Diameter of core 0.135
BTMG50H 2.3 191 343 152 76 76 (Inch)
BTMG90H 4.1 545 700 150 75 60
Core eccentric <1/16
BTMG170H 7.7 645 750 200 90 75
BTMG200H 9.1 1524 1588 127 51 51
Weight 0.243
BTMG320H 14.5 496 700 250 142 130 (lbs / feet)
BTMG400H 18.1 1524 1626 152 76 76
Standard coil length 1000
Packaged Anode BTMG480H 21.8 700 960 250 150 140 (feet)
BTMG600H 27.2 1510 1750 250 115 115 Coil weight 110
www.bsstechnologies.com BTMG1200H 55 1170 1400 330 170 145(T) 175(B)
1119R11
 SACRIFICIAL ZINC ANODE

Information
SACRIFICIAL ZINC ANODE
Zinc Anodes are usually applied in Low Resistivity Soils below 1000 Ω -cm and in Seawater or produced Brines.
Zinc should not be used when the electrolyte temperature is or exceeds 135ºF. Pre packaged Anodes are in standard
backfill (75% Gypsum, 20% Bentonite and 5% Sodium Sulphate).

ZINC ALLOYS Weld on Type Anodes - Single Strap

Core Dimensions(mm) Zinc Anode

Elements ASTM B 418 Type I ASTM B 418 Type II Anode Type Anode Dimensions(mm)
Length Width Height Length Width Thk N.Wt(Kg) G.Wt(Kg)
MIL A-18001K BTZ053W 140 70 30 250 25 5 2 2.4
Aluminium 0.10 – 0.50 0.005 max BTZ082W 200 100 25 320 25 5 3.2 3.7
BTZ100W 305 85 45 440 30 5 4 4.5
Cadmium 0.025 -0.07 0.003 max
BTZ111W 305 85 45 440 30 5 4.5 5
Lead 0.006 max 0.003 max BTZ122W 270 100 40 440 30 5 5 5.5
Iron 0.005 max 0.0014 max BTZ146W 200 130 35 330 38 5 6 6.6
BTZ191W 300 155 30 405 38 5 8 8.6
Copper 0.005 max BTZ240W 340 150 35 500 38 5 10 10.8
Others(each) 0.02 max BTZ262W 400 150 33 500 38 5 11 11.8
Total others 0.05 max BTZ284W 400 150 36 500 38 5 12 12.8
BTZ288W 340 150 38 500 38 5 12.3 13
Zinc Remainder Remainder BTZ355W 380 140 38 520 38 8 15 16
BTZ422W 460 140 38 600 38 8 18 19
Zinc Hull Anodes Weld on - Tear Drop BTZ466W 535 135 51 680 38 5 20 21
BTZ511W 540 140 40 680 38 8 21.5 23
Core Dimensions(mm) Zinc Anode BTZ555W 680 125 40 740 50 6 24 25
Anode Type Anode Dimensions(mm)
Length Width Height Length Width Thk N.Wt(Kg) G.Wt(Kg) BTZ577W 800 120 40 940 50 5 25 26
BTZ012T 120 40 25 200 10 3 0.5 0.55 BTZ600W 540 140 48 680 50 8 25 27
BTZ024T 180 60 32 260 20 3 1 1.1
Weld on Type Anodes - Double Strap
BTZ048T 220 75 38 300 20 3 2 2.2
BTZ040T 200 95 30 300 20 3 3 3.2 Core Dimensions(mm) Zinc Anode
BTZ235T 275 175 51 405 40 5 10 10.6 Anode Type Anode Dimensions(mm)
Length Width Height Length Width Thk N.Wt(Kg) G.Wt(Kg)
BTZ240D 305 152 32 254 32 5 10 10.8
BTZ284D 305 152 38 254 32 5 12 12.8
305
Zinc Hull Anode Bolt On Type
BTZ333D
BTZ435D 305
152
152
50
64
254
254
38
38
5
5
14
18.4
15
19.6 Zinc Anode
Anode Plate
Type Length(mm) Width(mm) Height(mm) C-C(mm) Plate Width(mm) Thickness(mm) Net Wt.(Kg) Gross Wt.(Kg) Tear Drop Anodes
BTZ084B 200 100 30 110 75 3 3.4 3.8
Stand OFF Anodes
BTZ055B 200 100 40 110 75 3 4 4.4
BTZ166B 300 150 25 160 75 3 7.1 7.5 Tank Anodes
BTZ191B 300 150 30 160 75 3 8.2 8.6 Hull Anodes
BTZ244B 300 150 40 160 75 3 10.8 11
BTZ266B 300 150 50 160 75 3 11.6 12 Bracelet Anodes
BTZ337B 300 200 40 160 75 3 14.8 15.2
Electrochemical Properties :
Solution Potential: -1.05V w.r.t Ag/AgCl Capacity: 780 Ah/kg
Customized Alloy, Dimensions and shape can be produced against order www.bsstechnologies.com
1119R11
 MIXED METAL OXIDE ANODE (TUBULAR)
Information
Titanium is chemically resistant & mechanically robust. Mixed Metal Oxide when coated over Titanium activates the
IMPRESSED CURRENT ANODE latter . The Mixed Metal Coating has an excellent Eletrocatalytic property. The evolution of Oxygen & Chlorine and / or
mixtures of the two Gases can be established with a Low Stable Anode Potential.

Composition
Mixed Metal Oxide Coating is a combination of precious groups of Metal Oxides . The Oxide composition has been extensive-
ly developed for optimized Electrochemical & Long lifetime in the various Cathodic Protection Environments.

Lifetime
BSS Tech recognizes the simultaneous generation of Chlorine & Oxygen on the stringent environment the Anode inhabit. And so
we provide Mixed Metal Oxide to withstand these harsh conditions. Concurrent Anodic generation of Chlorine & Oxygen occurs
in Low Salinity / Brackish / Fresh Water . Hydrogen ions co-generated with Oxygen have a particular stagnant Electrolyte flow ,
which results in very acidic conditions at the Coated Electrolyte Interface. Mixed Metal Oxide Anodes are designed to resist acidic
conditions & the coating to the Titanium Interface is protected from Anodic and Chemical attack .It has a very low wear rate in the
range of 0.5 to 4 mg/A-year; depending on the specified Cathodic Protection Application & Conditions. The long lifetime behaviour is
only because of the Low Electrochemical wear of the Coating provided for a stable low Anodic Operating Potential. We design our Mixed
Metal Oxide Tubular Anodes for a lifetime of 10 to 30 years , even longer depending upon the Application & Customer requirement.
MMO Anode Tubular Current Outputs
Mixed Metal Oxide Anodes have High Current Outputs . The recommended maximum Current Density depends upon the Resistivity
& Composition of the Electrolyte. As with all Anode Systems, the lifetime is a function of the Current Density.
The recommended maximum current outputs are:

Sea water 750 A/m2 Brackish/ Fresh water 150 A/m2

Soil (Carbonaceous Backfill) 100 A/m2 Mud 50 A/m2

Dimension & Size

BSS Tech Mixed Metal Oxide Tubular Anodes are available in all Lengths & Diameters. We also provide other types of Mixed Metal Oxide
Anodes which includes : Rods, Wires, Discs, Sheet, Expanded Mesh, Strip and can be tailor made to suit our Customer’s Specification
& Requirements. Canistered MMO Anodes also available with different sizes.

Applications
Major applications for Mixed Metal Oxide Anodes include: • Internal Cathodic Protection for Tanks, Condensers & Heat Exchang-
ers,etc. • External Cathodic Protection on Pipeline, Ships, Platforms, Jetty Structures, Offshore Structures, Seawater intake
structures. • Buried Structures (used with Carbonaceous Backfill) • Tank Bottom Protection

www.bsstechnologies.com
1119R11
 MIXED METAL OXIDE RIBBON ANODE
Information

Titanium is chemically resistant & mechanically robust. Mixture of Metal Oxide when coated over Titanium, activates
IMPRESSED CURRENT ANODE
the latter. The Mixed Metal Coating has an excellent Electrocatalytic property. The evolution of Oxygen & Chlorine and /
or mixtures of the two Gases can be established with a Low Stable Anode Potential.

Composition

Mixed Metal Oxide Cathodic Protection Coating is a combination of precious groups of Metal Oxides. The Oxide composition
has been extensively developed for optimized Electro Chemical & long lifetime in the various Cathodic Protection Environments.

Lifetime

BSS Tech recognizes the simultaneous generation of Chlorine & Oxygen on the stringent environment the Anodes inhabit. And so
we manufacture Mixed Metal Oxide to withstand these harsh conditions. Concurrent Anodic generation of Chlorine & Oxygen occurs
in Low Salinity / Brackish / Fresh water . Hydrogen ions co-generated with Oxygen have a particular stagnant Electrolytic flow, which
results in very acidic conditions at the Coated Electrolyte Interface. Mixed Metal Oxide Anodes are designed to resist acidic conditions
& the coating to Titanium interface is protected from Anodic & Chemical attack . It has a very low wear rate in the range of 0.5 to 4mg/
A-year; depending on the specified Cathodic Protection Application & Conditions . The long lifetime behaviour is only because of
the Low Electrochemical wear of the Coating provided for a stable low Anodic operation potential. We design our Mixed Metal Oxide
Ribbon Anodes for a lifetime of 10 to 40 years, or even longer depending upon the Application & Customer requirement.

Current Outputs Mixed Metal Oxide Ribbon Anode

Mixed Metal Oxide Anodes can have different output ratings based on the life & current requirements . The recommended maximum
Current Density depends upon the Resistivity & Composition of the Electrolyte as with all Anode systems, the lifetime is a function of the
Current Density.

The recommended current outputs are:

Size (Width x Thickness) Current Output

0.25” x 0.025” 17 mA/m 33 mA/m 42 mA/m 70 mA/m 105 mA/m

(6.35mm x 0.635mm)

Applications

Mixed Metal Oxide Ribbon Anode is primarily used for Tank Bottom Cathodic Protection System.

Packing

Mixed Metal Oxide Ribbon Anodes are available in rolls of 250 feet or 500 feet.

www.bsstechnologies.com
1119R11
 PYRAMID ANODE
Information

The Pyramid Anode consists of a four-vaned titanium substrate coated with mixed metal oxide, IrO2/ Ta2O5, conduc-
tive film, mounted on a high-density waterproof concrete pyramid to provide negative buoyancy and sea- bottom
stability. Water seals are designed to established engineering principles and do not rely upon the dubious effectiveness
of fillers, mastics, resins and the like.

The anode, when fully assembled with special double-armoured insulated cable, requires only the installation contractor to
lower the anode on to the seabed and terminate the onshore end of the cable, resulting in minimal installation time, and
further cost savings.

The Pyramid Anode is ideally suited for well casing, platforms, sheet piling, jetty piles and all similar offshore facilities with a
Pyramid Anode with Cable current output as per customer requirement.

Top piece:
Titanium rod anode with MMO coating with four numbers of TIG welded Titanium Fins with MMO Coating.

One end of the central rod is provided with internal thread suited to assemble on base axle.

Base Piece:
Titanium Base Axle coated with MMO. One end with an external thread to assembly the top piece and other end machined for cable
connection with tubular PVC housing.

Substrate
Titanium ASTM B265 Grade1/ 2 Top piece
Coating:
Oxides of Iridium & Tantalum
Base piece

Concrete Base

www.bsstechnologies.com Pyramid Anode

1119R11
 JACKMO TM WIRE ANODE
JACKMO TM

JACKMO Wire Anode is an impressed current, flexible anode used for cathodic protection of buried structures
TM

like tank bottom, underground vessel, Piping etc. Anode shall be placed in close proximity to buried metal structure. WIRE ANODE
JACKMO TM Wire Anode provides uniform cathodic protection to every point, with minimum interference from adjacent
structures. This anode has the advantage of effective uniform current distribution, long life, flexible in construction, easy
installation and lower ground contact resistance. The JACKMO TM Wire anode assembly is mixed metal oxide over titanium
substrate (MMO/Ti) piggy backed on 10mm2 HMWPE/Kynar cable prepacked with coke breeze in woven fabric tube like sack.
Cable size, type and connection frequency can be customized to suit the project requirement.

Specification:

Anode Wire Diameter 1mm 1.5mm 3mm

Maximum Current output * 314 mA/m 471 mA/m 942 mA/m

Design Life 20 years at Max. Current output*

Mixed Metal Oxide

Ir-Ta
Catalyst

Titanium substrate ASTM B348 Grade I / II

Backfill Calcium Petroleum Coke

Sock Material Porous non-woven fabrics

Sock dimension 38mm Diameter(Approx)

150 Meters (Customized length at

Length per reel
requested)

Cable To suite design requirements

www.bsstechnologies.com
1119R11
*NOTE:- Other Rating are also available based on customer request
 GRAPHITE ANODE
Typical Application

IMPRESSED CURRENT ANODE Graphite anodes perform best under Dry Soil conditions, though it operates in Aqueous Environment. The effective-
ness of these Anodes are increased with the use of Backfill as it increases the Anode Discharge Surface Area &
lowers the Anode -to- Earth Resistance. Graphite Anodes have been successfully used in both Conventional & Deep
Ground- Bed applications . They provide excellent Protection in Environments with high Chloride.

Anode Consumption

Graphite is the most commonly used material as an Anode in the impressed Current Cathodic Protection Industry . It is an
excellent Conductor of Electricity , Chemically Resistant and is easy to Machine . Due to its proven long term Performance &
Economics, Solid Graphite Anode is very popular in ICCP systems.

With strict Quality Control Guidelines , BSS Tech manages a complete line of Graphite Anode . These Anodes are composed
of high quality Petroleum Coke mixed with Coal Tar Binders & extruded into Various diameter Rods. Rods are heated repeatedly
over 2,600oC and then cooled . The complete process results in Anodes with high percentage of Carbon, which in turn delivers
effective Protection at very low consumption rate . The consumption rate varies between 0.4 and 2.0 lbs/A year. (The recommended
Current Density for the Graphite Anode is 0.5 A/ft2.)

Graphite is Porous

To increase the Anode life the pores are filled with Impregnate. Graphite Anodes are treated with a Microcrystalline Wax. This limits any
electrochemical activity to the surface of the Anode and reduces any tendency for the reaction to occur in the Pores . This also acts as a
barrier against moisture intrusion which could cause deterioration of the Anode and possibly the Anode Connection. An alternate
treatment is a Phenolic Resin, which is recommended for use in severe application Environments.
Graphite Anode Fabrication Options

Treatment: Paraffin Wax, Phenolic Resin

Connections: Centre Connected, End Connected, Any Depth

Standard Connection

All Graphite Anodes are precision drilled to Customer’s specified depths. The wires are soldered with each Anode assures a quality,
fault - free connection . Maximum Electrical Resistance of the connection is 0.0004 Ω & the minimum Pullout Strength is 1000 lbs.

Sizes & Operating Data

Recommended Max A
Size Untreated Weight Treated Weight Area(ft2)
Backfill Saltwater Fresh water

3” x 60” 27# 30# 4.0 1.5 - 2.0 2.0 1.0

4” x 80” 65# 72# 7.0 2.0 - 4.0 4.0 2.0
www.bsstechnologies.com
1119R11
 HIGH SILICON IRON ANODE
Anode Consumption

IMPRESSED CURRENT ANODE

Stick Type
ANODE
TYPE WEIGHT DISCHARGE DIAMETER LENGTH AREA
(A)

Tubular Type
ANODE
High Silicon Iron Anode
TYPE WEIGHT DISCHARGE DIAMETER LENGTH AREA
(A)

www.bsstechnologies.com
1119R11
 ZINC RIBBON ANODES

GROUNDING PRODUCTS
Information
Zinc has proven to be an excellent Anode Material for Cathodic Protection and groundingt. To overcome
the small impurities which are always present in the base material, conventional Zinc Alloys contain Aluminium.
Zinc Anodes have been in use for decades to protect Steel Structures from Corrosion . Today, these anodes are still
widely utilized and have proven to be an effective choice for preventing corrosion in selected soils and brackish waters,
as a grounding electrode for AC mitigation applications.

Electro Chemical Properties

Open Circuit Potential (-v) 1.05 w.r.t Ag/AgCl, Current Capacity (A - hr/lb) - 372, Galvanic Efficiency (%) = 90 - 95

Features
High Current Output to volume ratio.
Easily conforms to any Cathode length or configuration.
Will not cause nor magnify stray currents.
Generally used in soils of 1000 ohm cm or less with prepared Gypsum-ClayBackfill.
Zinc Ribbon The Ribbon for AC mitigation is laid parallel to the cross country pipeline, laid as mats and in spiral for localised grounding

Applications
External areas of Steel Pipe Grounding of cross country pipelines
Tank bottom Cathodic protection of above grade storage tank. Interstitial spaces between old, corroded and new Storage Tank Bottoms.
In the limited space between Casing and Carrier Pipes.
In the limited space between inner and outer Casings of Wells of various kinds.

Product Size Plus Standard Small

Cross Section 5/8’’ x 7/8’’ 1/2’’ x 9/16’’ 11/32’’ x 13/32’’

Inches (mm) (15.88 x 22.22) (12.7 x 14.28) (8.73 x 10.32)
Pounds / Foot 1.2 0.6 0.25
(Kg / m) (1.79) (0.89) (0.372)
Zinc Ribbon for Road Crossing,
Dia. of wire core 0.135 0.130 0.115
AC mitigation,etc... Inch (mm) (3.43) (3.30) (2.92)
+20 +30 +50
Standard coil length 200+6.1 500+9 1000 - 0+15
Feet (mm) (61-0) (152-0) (305-0)
Standard coil ID 36 12 12
Inch (cm) (91.44) (30.5) (30.5)

Packaging Steel banded open coil Wooden Reels

www.bsstechnologies.com
1119R11
 PLATINIZED TITANIUM ANODES Platinized Titanium Anodes
IMPRESSED CURRENT ANODE
The substrate, usually titanium, is chemically resistant and mechanically robust. The substrate is activated by
platinum coating. The coating has excellent electrocatalytic properties. The evolution of oxygen and chlorine
and/or mixtures of the two gases is therefore achieved at low stable anode potential.

Composition

Anode comprises of a thin layer of platinum coated on titanium substrate.

Type of Anodes

Anodes are available in all shapes and forms including the following:

Rods, Wires, Tubes, Discs, Sheet, expanded mesh, strip and are custom made to the customer application and requirements.
Copper Cored Anodes are also available.

Applications:

Internal Cathodic protection of tanks, condensers, pipelines & heat exchangers.

External Cathodic protection of shiphulls, platforms, piers, dams, offshore structures & powerstation-inlets

Buried structures (used with carbonaceous backfill)

Tank bottom protection

Platinized Niobium Anodes – ICCP System

In modern ICCP-systems, Titanium and Niobium anodes are used. To realise a continuous current electrical conductivity and a long lifetime,
the anodes are applied with a thin layer of Platinum.

The composition and thickness of these coatings determine the working and the lifetime of the ICCP-systems. The construction, the electri-
cal output, current density and the characteristics of the electrolyte (freshwater, seawater, etc.) determine the size and shape of the anodes Platinized Titanium Anodes
Frequently employed applications

Internal Cathodic protection of storage tanks, condensers, pipes, pipelines, heat exchangers and boilers.

External Cathodic protection of pipelines, ship hulls, platforms and other offshore constructions, piers, dams and cooling
water inlet parts of power stations.

Tank bottoms.

We can provide this product to your specification and requirements

Niobium Anodes
www.bsstechnologies.com
1119R11
 PORTABLE REFERENCE ELECTRODES

REFERENCE ELECTRODES Copper / Copper Sulphate

Liquid or Gelatine Filled space age Porous Ceramic Plugs High Impact ABS Plastic (yellow) Housing Corrosive
Environment Resistant Chloride Ion Trap Equipped Copper Sulphate.
Connection Stud : ¼” - 20 Copper Size : 1” dia. x 8” Housing
Stability : ± 10 mV with 3.0 microamp load Temperature Range : 0º C to 57.2º C (32ºF to 135º F)
Silver / Silver Chloride
Liquid or Gelatine Filled Space Age Porous Ceramic Plugs High Impact ABS Plastic(Blue) Housing Corrosive Environ-
ment Resistant Chloride Ion Trap Equipped Silver Chloride.
Connection Stud : ¼” - 20 Brass Size : 1” dia. x 8” Housing
Stability : ± 10 mV with 3.0 microamp load Temperature Range : 0º C to 65.5º C(32º F to 150º F)
Zinc/ Zinc Sulphate
Portable Reference Electrodes Liquid or Gelatine Filled Space Age Porous Ceramic Plugs High Impact ABS Plastic (Red) Housing Corrosive Environment
Resistant Chloride Ion Trap Equipped Zinc Sulphate.
Connection Stud : ¼” - 20 Plated Brass Size : 1” dia. x 8” Housing
Stability : ± 10 mV with 3.0 microamp load Temperature Range : 0º C to 57.2º C (32º F to 135º F)
Portable Reference Electrodes are available with extension Rod water immersible Cable Connections and end weights for
Specific Application.
PERMANENT REFERENCE ELECTRODES (FOR SEA WATER APPLICATION)
Zinc Reference Electrode
Size : 2” dia. x 10” Long Lead Wire : Custom Made
Weight : Approx. 30 lbs Dimensions & Sizes can be Tailor Made Design life : 30 years
PERMANENT PRE PACKAGED UNDERGROUND REFERENCE ELECTRODES
Copper / Copper Sulphate
(for soil 200 ppm Chloride or less ) High Impact ABS Plastic Tube Packaged (Yellow Cotton Bag) in Special Non-Polarizing Backfill
Size : 2” dia. x 7” Pack Overall Size : Approx. 6” dia. x 14”
Permanent Pre Packaged Weight : Approx.15 lbs� Dimensions & Sizes can be Tailor Made Reinforced Rods : ¼” x 3” PVC @ Electrode End
Underground Reference Electrodes Lead Wire : Standard 50’ of # 14 RHH - RHW / Custom Made Design Life : 30 years
Stability : ±5 mV with 3.0 microamp load Temperature Range : 0º C to 57º C (32º F to 132º F)
Silver / Silver Chloride
(for soil 200 ppm chloride or higher) High Impact ABS Plastic Tube Packaged (Blue Cotton Bag) in Special Non-Polarizing Backfill
Size : 2” dia. x 7” Pack Overall Size : Approx. 6” dia. x 14”
Weight : Approx. 15 lbs Dimensions & Sizes can be Tailor Made Reinforced Rods : ¼” x 3” PVC @ Electrode End
Lead Wire : Standard 50’ of # 14 RHH - RHW / Custom Made Design Life : 30 years
Stability : ±5 mV with 3.0 microamp load Temperature Range : 0ºC to 65.5ºC (32ºF to 150ºF)
Zinc / Zinc Sulphate
(for soil 200 ppm chloride or less) High Impact ABS Plastic Tube Packaged (Red Cotton Bag) in Special Non- Polarizing Backfill
Size : 2” dia. x 7” Pack Overall Size : Approx. 6” dia.x 14”
Zinc Reference Electrode Weight : Approx. 15 lbs Dimensions & Sizes can be Tailor Made Reinforced Rods : ¼” x 3” PVC @ Electrode End
www.bsstechnologies.com Lead Wire : Standard 50’ of # 14 RHH-RHW / Custom Made Design life : 30 years
1119R11 Stability : ±5 mV with 3.0 microamp load Temperature Range : 0ºC to 57ºC (32ºF to 132ºF)
 MMO MESH RIBBON ANODE - Concrete Cathodic Protection

MMO TITANIUM MESH

Anode Ribbon Mesh is a key component for Cathodic Protection systems in new reinforced concrete structures. It is
composed of a precious metal oxide catalyst sintered onto an expanded titanium mesh substrate.
RIBBON ANODES

MATERIAL SPECIFICATIONS

Anode Performance:

Maximum anode concrete interface current density:

FHWA limit: 110 mA/m2

Short-term limit: 220 mA/m2

Type Width Current Output Anode Surface Area

A 10 mm 2.8 mA/m 0.027 m2 /m

B 13 mm 3.5 mA/m 0.032 m2 /m

C 19 mm 5.28 mA/m 0.048 m2 /m

TITANIUM
Expected life (NACE Standard TM 0294-2016): 75 years CONDUCTOR BAR
Catalyst: Mixed Metal Oxide

Expanded thickness: 0.9-1.3 mm

Dimensions common to all types

Substrate:
Material Titanium, Grade 1, as per ASTM B265
Coefficient of thermal expansion 8.7 x 10 - 5/o°K
Thermal conductivity at 200o°C 15.6 W/mo K
Electrical resistivity 0.000056 ohm-cm Titanium Conductor Bar
Modulus of elasticity 105 GPa Type Solid Ribbon
Tensile strength 245 MPa Material Titanium, Grade 1, as per ASTM B265
Yield strength 175 MPa Dimension 12.7mm (W) x 0.9mm (T)

Elongation 24% minimum Electrical Resistance 0.11 Ohm/m

www.bsstechnologies.com
1119R11
CORROSION RATE MONITORING PROBES CORROSION RATE MONITORING PROBES - Concrete Cathodic Protection
Corrosion rate monitoring probes are designed for installation during the construction of structures to provide
information on the corrosion of the reinforcement and the condition of the concrete. This is done in the form of the
following measurements:
Corrosion potential (Ecorr) of the probe working electrode and the main reinforcement with respect to the probe
reference element.
Corrosion rate(Icorr) of the probe working electrode and the main reinforcement using the linear polarization
resistance (LPR) method
Concrete Resistivity
Concrete temperature

Major Applications – Concrete Cathodic Protection

We can provide this product to suit your specification and requirements

Silver / Silver Chloride Permanent Embeddable Reference Electrode

Information
Ag/AgCl Reference Electrode Silver / Silver Chloride reference electrode is specially designed for concrete application having stable potential and long life. The
components are Silver metal, Silver chloride, silver ions and chloride ions.
Stability - Less than +/- 3mV in 24 hours. Lessthan +/- 10mV expected in 20 years.
Life in Concrete - morethan 30 years at a leakage current of 1mA
Housing - ACETAL Plastic / Nylon tube.
Contact surface - Micro porous plug
Temperature range: -5�C to 70�C
Approx. overall dimension - 4" long x 1" dia.

Potential:

-15mV +/- 10mV versus the Saturated Calomel Electrode (SCE)

230mV +/- 10mV versus the Standard Hydrogen Electrode (SHE)

Cable:

Supplied to order as required

QA/QC:

www.bsstechnologies.com All reference electrode are factory calibrated and supplied with calibration certificates.
1119R11
 GROUNDING PRODUCTS

Applications
GROUNDING PRODUCTS
Zinc Grounding Cells are used for AC Mitigation. This is used to bleed off AC from the structres, which are subject
to induced AC. Zinc Grounding cell can be installed at high voltage O/H crossing or parallelism locations.

Information

Zinc Grounding Cells consist of one , two or four Standard Zinc electrodes separated with 1” Insulating Spacers (for more
than 1electrode). Nominal resistance of a two electrode Grounding Cell in wet area is 0.2 to 0.6 Ohm. Nominal Resistance
of a four electrode cell is one fourth to one half that of a two electrode cell. The Grounding Cells are packed in standard backfill
(75% Gypsum, 20% Bentonite and 5% Sodium Sulphate) either in a unit of one, two or four.
Zinc grounding cells helps to bleed off unwanted voltages . They reduce
danger of shock on a steel structure, arcing and burning of insulated joints.
Composition (ASTM B 418 TYPE 1) Zinc grounding cells form an unavoidable part of any induced AC
power mitigation , protection of IJ’s and IF’s, earthing of a structure, etc.
ELEMENT CONTENT(%)
Polarization Cell Replacement (PCR)
Zinc Grounding Cell
Cu 0.005 max
PCR is a solid-state device designed to simultaneously provide DC decou-
Al 0.10 - 0.50 pling and AC continuity/grounding when used with cathodically protected
Fe 0.005 max structures, such as pipelines, tanks, grounding systems, and cable casings.
The PCR has very high AC fault current and lightning surge current ratings.
Cd 0.025 to 0.07 Polarization cell replacement (PCR) are used in conjuction with grounding
Pb 0.006 max cells.

Zn Remainder Isolation Flange Kits and Surge Arrestor

Isolation Flange Kits are used in flanges to isolate the protected and un
Potential -1.05 Volts w.r.t Ag / AgCl
protected sides of the pipeline. It consists of non metalic gasket, washer, Polarization Cell Replacement
Capacity 780 amps Hr./Kg. sleeve and metalic washer. Surge Arrestors are used to bypass the surges
between isolated structures and protect the insulating materials. (PCR)
Surge Arrestor
Type E Insulating Gasket

Standarnd Zinc Grounding Cells

NET GROUNDING CELL DIMENSION GROSS

MODEL
WEIGHT (L x W x D) (MM) WEIGHT
BTZN - 180 G 8.1 Kg. 37 x 37 x 915 32.0 Kg.

BTZN - 330G 14.9 Kg. 37 x 37 x 1524 44.7 Kg.

Nut Bolt-Stud Steel One-Piece Insulating Steel Nut
BTZN - 570G 25.7 Kg. 760 x 65 x 75 55.2 Kg. Washer Sleeve & Washer Washer

BTZN - 600G 27.2 Kg. 51 x 51 x 1524 58.9 Kg.

Isolation Flange Kit
www.bsstechnologies.com
1119R11
 GPS CURRENT INTERRUPTERS
Current interrupters are used in CP survey. TR unit output is switched ON and OFF at same instant. Usually TR units
are placed far way from each other and it becomes difficult to achieve time synchronization. GPS interrupter provides
solution for time synchronization.
GPS TIMER BSS TECH GPS interrupter has all necessary features required CP survey.
The GPS interrupter is made rugged. The equipment has bright LCD displays which helps operator to use the display under
the bright sun. The multiple keys membrane key pad makes it convenient for the operator. In built programme storage capability
and the real time clock back up battery gives the freedom to leave the unit un attended for several days. Auto synchronisation
does the checking of the clock with the Satellites and continues with the accurate timer, which gives accurate interruption when
multiple units are installed for surveys. Activating night sleep will enhance the battery service.
GPS
The global positioning system is a satellite-based navigation system consisting of a network of 24 orbiting satellites that are eleven
thousand nautical miles in space and in six different orbital paths. The satellites are constantly moving, making two complete orbits
around the Earth in just under 24 hours. One can receive satellite signals anywhere in the world, at any time. The biggest benefits over
previous land-based navigation systems is GPS works in all weather conditions.
This Satellite Clock information is as accurate as Atomic Clock and this is used as Time Source for our Timers achieving the most accurate
synchronisation possible.The convential Electronic clock has limited time accuracy. Most commonly used Industrial Real time clock claim
accuracy of ±15 seconds per month i. e. ½ second per day. Further the clock accuracy depends on various factors like external tempera-
ture, aging of components etc.

The system consists of

1. GPS Antenna.
2. Coaxial cable with MCX connectors.
3. GPS Interface Module.
4. Timer with User Interface.

Brief Specification
1. Microcontroller based digital circuitry.
2. ON time and OFF time independently adjustable from 0.1 to 999 Sec.
3. Built-in GPS Module with Lat-Log display feature
4. Built-in Real Time clock with Quartz crystal time base for high timing accuracy.
� Typical accuracy +2 PPM (170mS per 24 Hrs.) in non GPS Mode.
� Typical accuracy +5 PPB (1mS per 24 Hrs.) in GPS Mode.
5. Dust proof membrane key board for programming.
6. Digital LCD display for showing real time, ON/OFF cycle time, & Lat-Log parameters
7. Lithium Battery back-up for real time clock.
8. Programmable operation for Automatic Start & stop of Timing Cycle.
9. Provision for synchronisation with other timers or with external master clock .
10. Night sleep feature
11. Power fail compensation and auto re-start during Synchronised operation
12. Power Supply : 12V DC or 230V AC
13. Capacity to Interrupt up to 100A DC or AC current
www.bsstechnologies.com 14. Battery back up
1119R11
 MPPT CHARGE CONTROLLER
MPPT CHARGE CONTROLLER
MPPT charge controllers, CC series is for off-grid solar system and control the charging and discharging of the
battery, especially suitable for Cathodic Protection Application. The controller features a smart tracking algorithm inside
that maximizes the energy from the solar PV module(s) and charge the battery. CC series is very simple to configure and
use. This series of charge controllers are optimized for long battery life and improved system performance.
Features: Basic Architecture of CC Powered CP
•
SOLAR ARRAY
Intelligent Absorption charge time adjustment. CP DC DC CONTROLLER

• Optimized battery charge protection

CC-MPPT
• Enhanced Sleeping Mode
• Enhanced Power Saver Modes
• Over charging and Short circuit protection
•
BATTERY BANK
Efficient Thermal Design and Cooling CP LOAD

Technical Feature:

CC-MPPT-1224-20/40 CC-MPPT-36-20/40 CC-MPPT-48-20/40

Technology: Dual Channel Interleaved Buck Converter
Battery bank voltage: 12 / 24V 36 V 48 V
Maximum Charging Current: 20 A / 40 A 20 A / 40 A 20 A / 40 A
Maximum Solar Panel Voltage: 70 Volts 100 V 100 V
Maximum Power Point Voltage Range: Battery voltage to 70V Battery voltage to 77 V Battery voltage to 77 V
Buck Converter Duty Cycle Range: 0 – 100% 0 - 100% 0 - 100%
Idle Current from Battery (Typical): 21 / 18 mA (Sleep Mode) 21 / 18 mA (Sleep Mode) 21 / 18 mA (Sleep Mode)

Product Range:

MODELS Nominal Battery Voltage Maximum Charging Current Maximum Solar Panel Voc

CC-MPPT-1224-20 12 / 24 V 20 A 70 V
CC-MPPT-36-20 36 V 20 A 100 V
CC-MPPT-48-20 48 V 20 A 100 V
CC-MPPT-1224-40 12 / 24 V 40 A 70 V
CC-MPPT-36-40 36 V 40 A 100 V
CC-MPPT-48-40 48 V 40 A 100 V
CC-MPPT-1224-20H 12 / 24 V 20 A 150 V
CC-MPPT-36-20H 36 V 20 A 150 V
CC-MPPT-48-20H 48 V 20 A 150 V
CC-MPPT-1224-40H 12 / 24 V 40 A 150 V
CC-MPPT-36-40H 36 V 40 A 150 V
CC-MPPT-48-40H 48 V 40 A 150 V
www.bsstechnologies.com
1119R11
 ANTI FOULING SYSTEM
ANTI FOULING SYSTEM Description

The cathode is formed with an insulated steel frame containing copper and aluminium anodes making use of

impressed current system basics. The anode/cathode unit is suspended / placed at the pump inlet so that all the water

entering the pump must pass the electrode unit. Dosage levels of copper ions are extremely small and measured in

micrograms per litre of seawater. Therefore, relatively small quantities of copper are required to provide protection depend-

ent upon the flow rate and life required.

Anti fouling system consists of two parts “the electrode unit and the control panel. The electrode assembly contains mainly

copper anodes. Aluminium Anodes are used in combination with copper in some applications. The actual number and size of the

anodes is calculated to suit each installation and available space for mounting the electrode unit. The anodes are connected to the

constant current rectifier located within a safe area. For variable pump flow, an intelligent logic is utilized in power supply to provide

right dosage of ions.

Basically there are three types of systems.

1. Conventional grid Anti Fouling System - The conventional Grid Anti-Fouling system has the capability to deliver ions in the open
Conventional grid Anti Fouling System
sea at the mouth of the pipe or channel which is at risk of fouling.

2. Strainer System – Strainer Anti-Fouling systems are fairly small units shaped like Strainers and are attached at the mouth of the pipe

or at the mouth of the pump inlet. These are mostly vertically installed.

3. Skid Mounted Anti-Fouling System – Skid Mounted produces the copper ions in a process vessel. The produced treated water is then

delivered to the right part of the inlet in the right proportion to set the required ppb level.

All these systems can be prepared with logics to control automatically the production of ions and dispatch of ions depending on the

variation in flow rate. The system is intelligent enough to decide the production from minimum to the maximum designed while the flow is

zero to the maximum for the pump.

Benefits of our Anti-Fouling System Include:-

Reduction in power requirements

Skid Mounted Anti-Fouling System
Low maintenance system

No handling or storage of chemicals required

www.bsstechnologies.com Environmentally acceptable Aluminum anode & Copper anode

1119R11
 MARINE CATHODIC PROTECTION

BSS Tech has introduced marine cathodic protection services to serve the corrosion control needs of the marine MARINE CATHODIC PROTECTION
industrial structures like jetties, offshore platforms, offshore pipelines, ships, Jack up rigs, Harbor Quays,
Submarines, Offshore wind foundations etc.
Deep water platforms and pipelines present new challenges for design, maintenance, inspection and retrofit of corrosion
control systems. Our expertise includes marine survey, CP systems, Anti-Fouling systems & retrofits
Marine Surveys
The advent of the remotely operated vehicle & other survey techniques has radically altered corrosion survey and inspection
practices. BSS Tech can render the below mentioned surveys with our expert engineers to gather, analyze and interpret data as
per international standards. Several factors like water depth, water currents, location, depth of burial, size or length, cathodic protec-
tion system age and cost etc, determines which type of method to be used.
We offer the following services for offshore pipeline & structures:
• ROV Surveys
• Towed Fish / Trailing Wire Surveys
• Drop Line Platform Survey
• Guy Line Platform Survey
• Remote Electrode Submersible Survey
• Trailing Wire Landfall / Outfall Surveys
• Hybrid / Trailing Wire Surveys
Marine/Offshore structures can be protected by different means of CP systems
• Sacrificial Anode System
The structures which are commonly protected using SACP systems
includes ship’s hulls, propellers, Ballast tanks, Sea water intakes.

• Impressed Current Anode System

A well known reliable system used to protect marine offshore structures MMO Elliptical Anode for Vessel
is by ICCP system. The correct placement of ICCP components is the
critical factor for balanced operation and is necessary to provide
uniform current distribution and sufficient current density.
MMO Linear Anode for Vessel
• Anti Fouling System
An effective anti fouling system enhances the efficiency of the marine vessels and offshore structures by preventing bio fouling.
Different types of Anti Fouling system includes
1. Conventional grid Anti Fouling System
2. Strainer System
3. Skid Mounted Anti-Fouling System
www.bsstechnologies.com
1119R11
 AC MITIGATION MODELLING

AC MITIGATION MODELLING
Introduction

Pipelines running into close proximity with electric power transmission and distribution systems will occur electromagnetic
field created by the alternating current (AC) (expands and collapses and changes direction 120 times per second). An
alternating electromagnetic field will exhibit an induced voltage on the pipeline. In addition, power conductor faults to ground
can cause substantial fault currents in the underground structure. Stray alternating currents can cause corrosion on pipelines,
damage to the coating, resulted in metal loss and pipeline leak. Even though the corrosion weight loss for AC currents is less than
for equivalent DC currents, the magnitude of AC stray current is often large–hundreds of amperes under electromagnetic induction
and thousands of amperes during power line faults. These high current levels can produce a shock hazard for personnel and can
damage the structure and related equipment. There are three basic methods by which AC currents and voltages appear on metallic
structures near AC power lines such are Electrostatic coupling, Electromagnetic induction and Resistive coupling.

Need of Mitigation

AC interference on the pipeline due to inductive, capacitive and resistive coupling between the power line and the pipeline produces the
following risks:

• Shock to personnel under normal (steady state) operation

• Shock to personnel under fault conditions

• Electrical arcing under fault conditions causing puncture or damage to pipeline

• AC-enhanced corrosion under steady state operation

• Damage to the coating due to electrical stress under fault condition

Mitigation Modelling

Mitigation Modeling is used to compute/model the AC interference pattern in cases where either one component (OHL or Pipeline) in

absent or energized.

Physical Testing

• AC Testing

• Measurement of AC voltage to Ground

• Pre Testing (In case of Existing OHL & Pipeline)

• Safety
www.bsstechnologies.com
1119R11
 MONITORING ANODE

Monitoring anode performance can help operators predict overall CP system life.
MONITORING ANODE
Anode monitoring system provides a reliable, accurate method for monitoring anode performance and consumption. This
is designed to monitor and confirm performance of the Sacrificial Anodes. Monitoring Anode System have an excellent
record of success and are found on more offshore structures worldwide than any other fixed-monitoring system. They have
been applied to all galvanic anode types, including platform anodes, flush-mount anodes, onshore and offshore pipeline
bracelets.

A standard monitoring anode consists of the sampled anode installed with isolation on structure and wired to the monitoring panel.
Anode isolation from the structure is achieved by having an isolation joint.

A most sophisticated monitoring anode consists of total remote monitoring with switching capabilities. HWL HWL

MONITORING JUNCTION BOX

SACRIFICIAL MONITORING ANODE

ISOLATED SPOOL OR
ISOLATION JOINT

Monitoring system shall be designed to meet the following

requirements :

Anode monitoring system allows operators to accurately

measure anode consumption and remaining life without
interference with the anode. The data for a handful of
anodes will give general trends for the entire cathodic-pro-
PLATFORM / STRUCTURE
tection system.
MONITORING ANODE INSTALLATION LAYOUT
The performance of the Sacrificial Anodes are judged by
the measurement of current output of Individual Anodes.

Structure potential can be measured using Zn or Ag/AgCl INSTALLATION DETAILS

Reference Cell for the potential at the rated current out
from anodes

Verification of anode performance allows corrosion

engineers to evaluate not only the design of a particular
system, but the design methodology in general.
www.bsstechnologies.com
1119R11
 HYPOCHLORITE RECTIFIER
HYPOCHLORITE RECTIFIER
We manufactures High power rectifiers that serve hundreds of industrial, commercial and research applications.
These industrial applications require the use of direct current ranging from 1KA to 10KA for power ratings of 100kW
to 1MW. We offer both standard and highly customized designs for your rugged industrial application.
Rectifier cooling options for these supplies include forced-air, oil cooled, direct water, convection as well as a variety of
closed loop systems. Our highly customizable systems also feature a variety of control and monitoring options, which
include digital and analogue communication for interface with an upstream PLC or computer system.

Applications
Custom designed units for applications that include:

Steel Plants Electrochemical Processes Electro winning Processes

• Continuous Strip • Chlorine • Copper, Cobalt, Gold, Zinc,
• Cranes • Hydrogen Lithium, Silver etc.
• Electromagnets • Oxygen
• DC Shop Power Mining Applications
Electrochlorination Systems • Underground Locomotive
• Desalination traction supplies
• Hypo-chlorination • DC Shop Power

Resistive Heating

High grade, hermetically-sealed semiconductors are mounted on heat sinks and are protected with quick-acting silver sand fuses. The PIV
rating of all semiconductors used is well above the ratings specified in standards. This increased PIV margin yields additional transient
voltage protection and a higher mean time between failure (MTBF).

Rectifier Transformer
Transformer coils are wound with continuous copper conductors, varnish impregnated, and then oven baked for protection against dust,
moisture, and fumes.
On a core using interleaved sheets of high-grade, grain-oriented silicon electrical steel designed for high efficiency.
Thermal-overload sensing devices are included in each leg of the transformer to detect winding over temperature due to single phasing,
overloading or loss of cooling.

Enclosure
Enclosures are rigid, welded, free-standing, self-supporting painted cold rolled sheet steel. The base of the rectifier assembly is a heavy
duty assembly formed from structural steel members with provisions for fork lifting of the supply.
The front and rear of the enclosure is serviceable through lockable, latch-type full length doors or panels. We can manufacture custom
designed units with any rating, cabin and Colour. Enclosures are treated with two coats of a suitable primer and two coats of light gray
RAL7035. Custom paint colors available upon request.
Remote mentoring and control can be provided through Analogue Transducers and Potential free contacts. These can be hooked to
Customer PLC/DCS system.
Standalone Digital Remote Monitoring and control can also be provided through RS485 serial link.
www.bsstechnologies.com
1119R11
 COMPOSITE REPAIR SOLUTIONS

As part of BSS Technologies enhancing its products and services to the existing clientele, we offer proven, reliable
and cost-effective composite repair solutions.
These products were developed in response to the industry's need for cost- effective, reliable and environ- mentally friend-
Composite Repair Solutions
ly solutions.

Composite Repair Wrap – is developed for quick, fast curing, in-situ and cost effective repairs for high temperture application
upto 250˚°C. The product application is flexible for tight access and complex shaped piping, pipelines and equipment. The repair
system can restore the functionality of corroded and leaking pipelines whilst providing protection against further corrosion attack
and can be applied at high temperature operating pipelines.

Clamp Type Protection – effectively integrating three attributes of online leak sealing technology: clamp, sealant and injection tools.
It is designed to contain the leak point by introducing higher pressure than leaking system pressure by hydraulic injection tools to fill
the clamp cavity with sealant compound. The sealant compound are capable of covering leaks within wide range of temperatures
and pressures, also compatible with most type of chemicals.

Anti Corrosion Cap – is proven to be cost effective in protecting nuts & bolts from corrosion.

Flange Protection - system prevents crevice corrosion problems at flanges. When applied together with Anti - Corrosion Cap for the nuts
and bolts, it provides total corrosion protection for flanges. It involves injecting gel to temporarily fill the void. The material is heated to lower
its viscosity allowing it to penetrate all the crevices. Flange Protection contains UV tracers which under UV light cause a light blue fluores-
cence for checking treatment.

Tubular Pile Protection – utilizes the natural power of currents, wave and tide to break down the marine colonization process on jetty
piles, platform jacket legs and well conductors thus prevents marine growth.

Clamp Type Protection Tubular Pile Protection Flange Protection

Straight Pipe Clamp Flange Clamp Elbow Clamp Composite Repair Wrap
Anti-Corrosion Cap

www.bsstechnologies.com
1119R11
 S
TE SC•3® Earth Contact Backfill
IA
C
O
SS LORESCO® manufacturers impressed current anode backfill for all field conditions. LORESCO® SC•3® is
A
designed specifically for demanding anode systems. LORESCO® meets all standards for impressed current anode
backfill. SC•3® carries an NSF certification. Other LORESCO® products are Replaceable Deep Anode Systems, AllVent
™ and PermaPlug.™ These products represent the finest innovations available for the deep-anode cathodic protection
industry. For quality, service, and price, specify LORESCO®

INSTALLATION MATERIAL DESCRIPTION SPECIFICATIONS

LORESCO SC•3 , due to its dust-free
® ®
LORESCO SC•3 is a surface
® ®
Fixed Carbon: 99.35%
manufacture, is simple to install by modified, blended, and sized carbon Ash: 0.6%
either mixing and pumping or by backfill with surfactants. Moisture: 0.05%
pouring dry. With deep anode systems, Volatiles: nil (950°C)*
pumping from the bottom up is • Predominantly round particles Bulk Density: 74 lbs. per cubic foot
recommended. LORESCO® SC•3® has • All particles surface modified for
superb pumping qualities due to the maximum electrical conductivity and The photo below is a magnification of Loresco SC•3
addition of surfactants and when high current applications
agitated in water, takes on the • Particle sizing to be dust free with a
characteristics of heavy mud. A maximum particle size of 1mm
recommended mix is seven gallons of • Minimum calcination temperature of
water per one-hundred pounds. After base materials is 1250° C
installing SC•3 , allow twenty-four hours
®
• Base materials are calcined under
Particles Before Coating Particles after Coating
settling time before energizing. The ISO 9002:2000 quality control
modified surface of the carbon particles • Surfactants are added to assist

NSF
coupled with the action of the pumping and settling
surfactants in SC•3 will achieve
®
• No de-dusting oils are used during
positive electrical contact by settling. the manufacture of base particles
Vibrating or compacting is not
necessary. See installation section in Certified to
this catalog for additional pumping data. NSF/ANSI 60

www.bsstechnologies.com
1119R11
 A
SS
O
C
IA
DEKOTEC GMBH

TE
S
Buried steel pipes for the transport of liquid and gaseous media are protected against corrosion by coating with
thermoplastic material or thermosetting compounds. While coating of the pipe is done in the factory, some parts and
installations of a pipeline remain that have to be coated on the construction site. Depending on pipe laying method,
trenchless or in open trench, only welded joints or also bends, T-pieces, flanges and valves have to be protected in the
field.
Based on materials like polyurethane, polyethylene, butyl rubber, petrolatum and combinations thereof, DEKOTEC is able to
DEKOTEC GmbH
offer a broad variety of proven corrosion prevention systems as well as tailor made solutions for special fields of application. Felderstraße 24,
51371 Leverkusen, Germany

Major Products

BUTYLEN tapes and systems

DEKOMAT wrapping machines for BUTYLEN-Tapes

LIQUITOL polyurethane coatings

For enquiries, please contact
Plastelen tapes and mastics
BSS Technologies
DEKOTEC Heat Shrink Sleeves Plot No: TP010524,
National Industries Park, Jebel Ali
Tel : + 971 4886 7015
Bitumen tapes
Fax : +971 4886 7013
Email : [email protected]
DEKOTEC Rockshield DRM-PP

1119R11
 S
TE
IA ATMOS INTERNATIONAL
C
O
SS Atmos International (Atmos) provides pipeline leak detection and simulation technology to the oil, gas, water, and
A
associated industries. The company was founded in 1995 in the UK by the inventor of the statistical pipeline leak
detection system – Atmos Pipe, now one of a suite of leak and theft detection solutions from Atmos. These technologies
are implemented on hundreds of pipelines in over 50 countries, including major oil and gas companies such as Shell, BP,
ExxonMobil, and Total.

ATMOS International Ltd

St Paul's, 781 Wilmslow Road,
Manchester, M20 2RW, UK

Major activities include

Statistical Pipeline Leak Detection and Location

Rarefaction Wave Leak Detection and Location

Model based Pipeline Leak Detection and Location

Non-intrusive Instrumentation for Leak and Theft Detection

Airport Hydrant Leak Detection

Theft Detection System

Online and Offline Hydraulic Simulation

Batch Tracking

Pig or Scraper Tracking

Operator Training Simulator

Gas Management System

For enquiries, please contact
Tank Farm Management
BSS Technologies
Plot No: TP010524, Maintenance
National Industries Park, Jebel Ali
Tel : + 971 4886 7015
Fax : +971 4886 7013
Email : [email protected]

1119R11
 A
SS
SAFETRACK BAAVHAMMAR AB

O
C
IA
TE
S
Safetrack provides the Cathodic Protection, Ground Circuit and Railway Industry with modern technologies for
connecting cables to steel structure.

The Pinbrazing method were improved dramatically by Safetrack when the patented electronic (Constant Energy) were
invented. Later the highly appriciated new S4 Automatic brazing gun were developed and fast become the only demanded
Safetrack Baavhammar AB
gun at many users. The gun make sure to minimize any operator failure and brazing is used to ensure a safe electrical connec-
Möllebergavägen 339-24,
tion to different types of steel structures. The pin brazing method is the perfect method to use in cathodic protection systems for 245 93 Staffanstorp, SWEDEN
application of jumper bonds on pipes, connection of measuring cables, installation of sacrificial anodes, test posts and grounding
installations. Using pin brazing for connecting bracelet anodes on pipe laying vessels (lay barges and reel barges) is the safest and
quickest method which ensure high performance of the pipelaying.

The great benefits with Pinbrazing:

Works in any weather condition, even rain and snow!

Fast, a complete bond takes 1-2 minutes

Can be used in all angles For enquiries, please contact

BSS Technologies
Ideal for pipelaying vessels
Plot No: TP010524,
Economical National Industries Park, Jebel Ali
Tel : + 971 4886 7015
Safe for the operator Fax : +971 4886 7013
Email : [email protected]
Low temperature, much less than thermit welding
Safe for the material as it does not melt the work material down.
www.bsstechnologies.com
1119R11
 S
TE
IA BARTHAUER SOFTWARE GmbH
C
S SO
A
Barthauer Software GmbH is a medium-sized company that has been operating in the German-speaking regions of
Europe for over 25 years. More than 1,000 customers are now using “Barthauer software”. About 40 employees are
dedicated to the maintenance, development and support of the company’s leading product, the database-driven pipeline
management system BaSYS.
Barthauer Software GmbH
Software for geoinformatics and water management Our motivation is the fair allocation and conservation of resources. We make information available over generations. We
Head Office Braunschweig support our customers in the responsible use of scarce resources through infrastructure information solutions.
Pillaustraße 1a
38126 Braunschweig Modeling and efficient design of individual information systems for geoinfrastructures - Software for design, operation and
management of supply and disposal networks.

With comprehensive functionality, flexibility, and practical benefits – especially in the water and waste water segments – the profes-
sional and efficient pipeline management system is used for infrastructure planning by civil engineers, the employees of special
purpose associations, municipal organisations and public services.

Through its “multi-platform concept”, the company offers integration with the GIS/CAD systems of leading global manufactures such as
Autodesk, ESRI, Intergraph and Bentley via a uniform user interface. With MS SQL Server or Oracle, Barthauer offers its customers a
choice of two database management systems.

In conjunction with the waste water workgroup formed by the German state building authorities, Barthauer has been developing and
implementing the current, “original” ISYBAU interfaces for comprehensive transfers of technical sewer data between customers and
vendors since 1991.

BaSYS covers all aspects of supply or removal

network lifecycle

Powerful network planning and design functions

Common GUI for all major CAD / GIS platforms

(ArcGIS, ACAD, Bentley Microstation, Intergraph
Geomedia)

Asset registry

Condition control and assessment

For enquiries, please contact
Rehabilitation planning
BSS Technologies
Plot No: TP010524, Asset evaluation, amortization
National Industries Park, Jebel Ali
Tel : + 971 4886 7015 Hydraulic masterplan
Fax : +971 4886 7013
Operation and maintenance
Email : [email protected]

1119R11
 A
SS
JPAC TECHNOLOGIES PVT. LTD.

O
C
IA
TE
JPAC Technologies Pvt. Ltd. Along with its flagship solution “Pipeline Construction Management System” has

S
been serving the Oil and Gas Pipeline industry. PCMS is an affordable, easy-to-use solution that integrates
planning, GIS, construction, documentation and asset management into one program with a built-in interface to enter
and retrieve information. Location and Status of each Pipe and Fitting gives the answers to when and where.
The system is designed to help you remember every single line item, right down to the last nail. Using a proven dynamic JPAC Technologies Pvt. Ltd.
query generation method that's much faster than a traditional spreadsheet, PCMS draws from an extensive database of field # 404, C-Wing, Eastern Court
data. Its flexible reports provide you with a number of ways to analyze construction progress linked with work procedures and Parleshwar Road, Vile Parle (East)
Mumbai - 400 057, INDIA.
material certificates.
Work smarter and faster with better document control and improved collaboration between clients, vendors, subcontractors and
consultants. Our comprehensive features will enable you to track, monitor, analyze, observe, Locate and store data and much
more. Our online Project Center will capture essential document information, making business processes more efficient and
effective.
Since PCMS is web-based software it provides a lot more benefits than traditional software, such as, on demand accessibility, fast
setup, quick customization requests etc.

SALIENT FEATURES
Hosted Application
Pipe Tracking using BarCode
Field Entry From Handhelds
Handheld App with BarCode
Instant Report Generation
Report Approval System
Generation of PipeBook
Generation of Progress
View Color Coded Activities
Assets with Attributes
The Major areas of Specialization Cut Pipe Nomenclature
Linked Quality Reports
Pipeline Construction Management System Customer Mapping For enquiries, please contact
Linked NDT Films
Inbuilt Report QC BSS Technologies
Document Tracking & Completions Safety & Outage Management
Plot No: TP010524,
Mechanical Completion
National Industries Park, Jebel Ali
Pipe & Material Tracking Field Survey & Mapping Completions Management Tel : + 971 4886 7015
Network Planning Infrastructure Management Solution Fax : +971 4886 7013
Email : [email protected]
Construction Management Web GIS Solutions and Services

Asset Management Remote Sensing and Photogrammetry

1119R11
 S
TE
IA IGP ENGINEERS PRIVATE LIMITED
C
S SO
A From a modest beginning in 1955, IGP group today provides over 55 products and services to the core sector. The
group’s products are well accepted in domestic and international markets.
IGP R&D team interacts with universities and technical associates to design new products. These products and
IGP Engineers Private Limited processes are developed using in-house facilities.
# 79, Valmiki Street, Thiruvanmiyur,
IGP group has established long term relationship with its customers through custom designed world class products and services.
Chennai – 600 041
IGP is Asia’s leading Gaskets Manufacturer. Apart from Gaskets, Monolithic Insulation Joints are developed & manufactured
in-house at IGP-Unit 2 facilities since 2002.
Monolithic Insulation Joints
 Are boltless, rigid pipeline components, factory welded and ready for installation at site.
 Provides electrical resistance between the pipeline sections and adjoining structures, thus improving the effectiveness of
MONOLITHIC the Cathodic Protection System (CP pipeline).
INSULATION JOINTS  Suitable for underground and above ground installations.
 Maintenance free – fit & forget.
Benefits:
 Eliminates electrical short circuits and stops stray current in pipeline systems.
 Most economical and reliable method that can be used for cathodic protection in all applications of the pipeline systems.
 Eliminates field assembly of bulky installations of Flanges, Gasket Kits with bolt & fasteners.
Mechanical Properties:
 The excellent mechanical properties are achieved by a rigid design of statically favourable form, using the thermos-setting
plastic free from clod flow as insulating material.
 The welded unit provides safe and reliable connection even over extremely long period of operations without risk of the secured
and locked unit losing or separating.
 The Joints have undergone all types of pressure tests requirements as per media of the fluid or application of the pipeline design
adhering to the international standards & testing requirements or customer special requirements at our works facilities.
Electrical Properties:
 The dimensioning and practical arrangement of the insulating sections within the overall design in addition to technical
production factors, in conjunction with insulation materials of a suitable quality, result in the ideal overall electrical behavior of the
insulating joints large external insulating length, thus eliminating the possibility of spark over.
 Very good dielectric strength, substantially greater than conventional insulating flanges.
For enquiries, please contact
Quality Control:
BSS Technologies  We are performing all pressure tests in-house, like Hydro, Pneumatic, Fatigue, Combined Cycle, Bent, Torsion, NACL Immersion,
Plot No: TP010524,
insulation resistance, Die-electric strength, adhsion and Holiday Tests.
National Industries Park, Jebel Ali
Tel : + 971 4886 7015
Fax : +971 4886 7013
Email : [email protected] Data Required for Manufacturing:
Pipeline application (fluid details), details of pipeline material, size, schedules, Design pressure and temperature.
www.bsstechnologies.com
1119R11
 A
SS
HEATH CONSULTANTS INCORPORATED

O
C
IA
TE
Heath is a manufacturer that provides products and services for the utility protection, asset management and HEATH

S
damage prevention markets. Our core focus is leak detection for the natural gas industry. We strives to keep up with CONSULTANTS
ever-changing market demands to provide state-of-the-art services and products to each of our customers.
Heath Consultants Incorporated
Heath Consultants has been a trusted name since 1933 as the leading provider of leak detection services and products to
9030 Monroe Road
the midstream, upstream and downstream marketplaces. Houston, Texas 77061 USA
Since our inception Heath’s highly qualified and experienced management team provides a strong direction that focuses on
customer service and satisfaction. We have an excellent track record with utilities throughout the United States and abroad.

Leading product manufacturer for the

Utility Protection, Asset Management &
Damage Prevention

Proven Products & Advanced Technologies

• Heath Volume corrector (HVC) • Detecto Pak-Infrared (DP-IRTM)

• Heath Data Recorder (HDR) • Flame Ionization (FI)

• Heath Chart Recorder (HCR) • Mobile Kits For enquiries, please contact

• Remote Emissions Monitor(RMLD-REM) • Sure-Lock® (Pipe & Cable locator) BSS Technologies
Plot No: TP010524,
• Optical Methane Detector (OMDTM) • Plunger Bars & Other Support Tools National Industries Park, Jebel Ali
Tel: +971 4 8867015
• Remote Methane Leak Detector-Intrinsically Safe (RMLD-IS™) • ODARATOR 2TM
Fax: +971 4 8867013
• Advanced mobile survey • EI - 5 Ethane Identifier Email: [email protected]

www.bsstechnologies.com
1119R11
 S
TE
IA MAGNETIC PUMPING SOLUTIONS
C
S SO Magnetic Pumping Solutions is a privately owned US company that develops, manufactures, tests, installs and
A services permanent magnet motor driven artificial lift systems. All engineering and development work is carried out
in the UK. The company has installed centrifugal pumps (ESP) running on permanent magnet motors, referred to as
Magnetic Pumping Solutions PMESP® and Progressive Cavity pumps referred to as PMPCP® for use in oilfield applications. Systems have been
The Dene, Ropley, deployed and are presently operating in the USA, Europe, Middle East and Asia.
Alresford SO24 0BG, United Kingdom
Permanent Magnet Motor Driven Downhole Pumping Systems
20 - 2000 HP Rating
10 to 60,000 BPD Flow Range
50 - 6000 RPM Speed Range for driving ESPs and PCPs
Benefits:

• High Efficiency compared to Induction Motors, In excess of 95%

• Green Technology with 20 to 75% power saving from existing technology
• Shorter and Cooler running systems that enhance Reliability and Run-Life
• Improved ESP and PCP performance in wells with High GOR or Slug Flow
• Advanced Gas handling capabilities with special automated algorithms
PERMANENT
• Single section PM motors with no tandem connections
MAGNET MOTOR
• Potentially one size smaller Cable and smaller transformer providing added cost saving and smaller footprint.
Applications
DRIVEN ESP / • High productivity wells where run life and performance of the pumping system is Critical
PCP SYSTEMS • Gassy wells
• Wells with low producing fluid rates
• Wells in which an ESP system may be installed below the perforations
• Wells with high bottom hole temperatures and scale issues
• High HP wells where the power saving is a significant factor
• High dogleg severity applications
• Fields with high cost electrical power or limited power availability
PM Control - PMVSD®

For enquiries, please contact • The Permanent Magnet Motor and the special Variable Speed Drive (PMVSD®) are the core components of the MPS PM driven
artificial lift systems.
BSS Technologies
Plot No: TP010524, • To reach the maximum efficiency while operating a PMM, the surface control logic in the PMVSD® will always be tracking the actual
National Industries Park, Jebel Ali position of the rotor in the downhole motor to ensure that the stator magnetic field controlled by the PMVSD® is maintained at the
Tel : + 971 4886 7015 optimum levels with respect to the rotor magnetic flux generated by the permanent magnets.
Fax : +971 4886 7013
Email : [email protected] • MPS is applying a proprietary control technique to always maximize motor efficiency and generated torque at various operating
conditions.
www.bsstechnologies.com
1119R11
 A
SS
OXFORD MONITORING SOLUTIONS

O
C
IA
Oxford Monitoring Solutions designs, manufactures and installs down hole, surface and remote monitoring solutions

TE
S
for the oilfield artificial lift industry. Our solutions are reliable, easy to understand and easy to implement in the field. We
specialize in monitoring and control solutions for electric submersible pump (ESP), progressive cavity pump (PCP), rod
pump (RP) and jet pump (JP) applications with a product offering spanning simple pump-off control gauges through to
Oxford Monitoring Solutions
Oakfield Industrial Estate,
complete field automation solutions with remote web based monitoring.
Eynsham OX29 4TH, United Kingdom

Product Range
• ESP Gauge Systems

• Downhole Permanent Gauge Systems DOWNHOLE MONITORING SYSTEMS

• Downhole Gauges for PCP, Gas Lift, Jet Pumps and other artificial lift systems

• Surface Monitoring Systems

• Real Time SCADA Solutions

Features:

• Wide range of products enabling a fit for purpose selection of gauge systems

• Wide operating temperature range (up to 175 OC maximum operating temperature)

• Modern electronic components, screened and tested individually for high reliability and
performance with advanced gauge layout and design.

• Gauge performance and run life tracking for extended utilization

• Capable of measuring up to 12 downhole parameters with multiple motor temperature

and pressure measurements.

• Plug and Play design with no requirement of field programming or calibration

• Value engineered product that provides high performance with attractive prices

Applications

• All oil producing wells

• Naturally Flowing wells

• Monitoring or exploratory wells

• Wells with Artificial Lift Systems For enquiries, please contact

• Water Wells BSS Technologies
• Gas Wells including CBM wells Plot No: TP010524,
National Industries Park, Jebel Ali
• Fields requiring real time monitoring and automation (Digital Oilfield) Tel : + 971 4886 7015
Fax : +971 4886 7013
Email : [email protected]

1119R11
 S
TE
IA THERMOPADS PVT LTD
C
S SO Thermopads is a multi-product, multi-service organization – one stop destination for all heating needs – with sales
A
service points covering every part of India and overseas branches in U.K, Germany, Singapore and U.S.A. The array
of company’s products have applications in almost all industries – Petroleum, Power Plants, Metallurgical, Cement,
Fertilizers, Textiles, Food and confectionery, Parma, Paints, Edible oils, etc.

Thermopads Thermopads manufactures/provides – Surface/immersion electrical heating equipments suited to hazardous and non-haz-
ardous environments.
Thermopads Pvt Ltd
Thermopads are leading manufacturers of heat tracing and heating cables in the world.
28, Nagarjuna Hills, Punjagutta,
Hyderabad – 500 082, INDIA Electric Heat Tracers are specialized heating cables with low watt density for applications.

- To maintain temperature of fluids in pipelines at elevated temperatures for ease of handling, storage and transfer

- To heat-up process fluids in pipelines/tanks/equipment.

Electric Surface Heating:

The main principle of ESH is that heat is applied to the exterior surface vessels/equipment being heated.

Thermotrace –HTT: Power limiting tracers, Cut to required length at site and in wide range of wattages. These Tracers are ATEX
certified

Thermotrace – CTL: Constant output, parallel circuit type, cut to required length at site and in wide range of wattages.

Self-Limiting Self Regulating Tracer – STP: Self-Limiting & Self-Regulating (SLSR) with variable output, temperature dependent,
parallel circuit type, cut to required length at site and in a wide range of wattages. These Tracers are ATEX certified.

Heating Cables – HC: Constant output, Series circuit type, heating cables insulated with PTFE, metal braided if required, outer PVC or
insulation combinations for use in both process heating and freeze protection applications. These Tracers are ATEX Certified.

Heated Hose: This product finds application in Gas analyzer sampling, Hot melt transfer in Petroleum, Chemical, Glue, Paint, Food
processing etc. where in the product inside the process tube (part of heated hose) needs to be maintained at critical temperatures to avoid
condensation / solidification of the gas or temperature drop in the fluid.

Floor Heating Cables & Mats: These are constant output, Series circuit type heating cables/mats for floor heating applications in
homes/offices, driveways, green houses in cold countries / places.

Salient features :
For enquiries, please contact
Simple Economical and Reliable
BSS Technologies
Plot No: TP010524,
Uniform Heating No Corrosion Problems
National Industries Park, Jebel Ali
Tel : + 971 4886 7015
Low capital and running costs Maintenance free
Fax : +971 4886 7013
Email : [email protected]
Ease of handling Precise temperature control

1119R11
 A
SS
O
C
ELMED DR. ING. MENSE GMBH

IA
TE
S
ELMED specialises in the design and manufacture of measuring and testing equipment. For over 60 years custom-
ers in many technical fields have been relying on this family-owned company. The ISOTEST product range is a handy
tool in the detection of coating defects and offers a reliable solution to corrosion protection within the framework of quality
control. By means of high voltage impulses coatings on a conductive basis can be gently NDT-tested. This method spots ELMED Dr. Ing. Mense GmbH
even the tiniest defects that are often missed during the normal visual inspection. Further advantages of the ISOTEST: testing Weilenburgstr. 39
with reserves of energy, guarantee of stability of selected test voltages, testing even on dirty of damp surfaces, very flexible at 42579 Heiligenhaus, Germany
use thanks to numerous accessories.

Products

For enquiries, please contact

ISOTEST inspect 35
BSS Technologies
ISOTEST inspect 8.0 Plot No: TP010524,
National Industries Park, Jebel Ali
ISOTEST 4S Tel : + 971 4886 7015
Fax : +971 4886 7013
Email : [email protected]
ISOTEST 4S plus

ISOTEST HV
1119R11
 S
TE
IA VP ENGINEERS
C
S SO VP Engineers AN ISO-9001:2015 Certified organization has a manufacturing unit near Chennai and evolved as
A an Engineering Enterprise picking the art of manufacturing products using different manufacturing processes with
materials like Poly Urethane, Plastic, Rubber & specialized Metal (Ferrous & Non ferrous, SS, etc).

VP ENGINEERS uses the following materials in the production

VP Engineers
# 79, Valmiki Street, Thiruvanmiyur, • Poly Urethane – Poly Urethane Cast & foam varieties, FRP, natural rubber, NBR, Neoprene, Viton.
Chennai – 600 041 • Metals – Ferrous & Non- Ferrous like Carbon & Stainless Steel, Copper Alloys, Nickel Alloys, etc.

• Plastics – PP, HPDE, LDPE, Polyamide 6,66 (Nylon), POM (Poly Acetal), ABS, PTFE, etc

Pipeline PIGS & CASING INSULATORS – END SEAL

VP ENGINEERS manufacturers Pigs in Various types, Sizes to suit end application, made out of PU/ NBR.
• Bidirectional Pigs

• Foam Pigs

• Batching Pigs
PIPELINE CLEANING PIGS
• Cleaning & Gauging Pigs

• Decoking Pigs

We also do Casing Insulator & Casing End Seal used in Oil/Gas/ Water Pipeline.

END Protectors & Insulation

To provide protection in pipe & Fittings VP Engineers manufacture following items

PIPE END PROTECTOR FOAM PIGS
• Pipe fittings Caps – OD, ID Fitting & Bevel Cap
INSERTS
• Flange End Protector – Box type, Belt type, PTFE & Metal.

• Flange Insulation – Collar sleeve / POM Sleeve

• Bolt & Nut Protector

Cooling Tower & Strainer Nozzle

CASING INSULATOR & END SEAL
VP Engineers offers nozzles, Grids for Cooling tower, WTP/ETP, etc.

For enquiries, please contact

BSS Technologies
Plot No: TP010524,
National Industries Park, Jebel Ali
Tel : + 971 4886 7015
Fax : +971 4886 7013
Email : [email protected]

www.bsstechnologies.com
1119R11
 A
SS
O
C
IA
TELE-FONIKA KABLE S.A

TE
S
The group TELE-FONIKA Kable S.A (TF Kable) is a recognized and trusted provider of copper and aluminum cables
and wires, optical fiber cables, used by the world’s leading companies in Mining, Energetics, Renewable Energy,
Railway industry, Automotive Industry, Telecommunication, Welding Industry, Shipbuilding Industry, Oil and Gas, Automat-
ics. We offer a comprehensive assortment of wires and cables. Apart from the standard assortment of products, we also offer
Tele-Fonika Kable S.A
special cables made to meet individual customer orders. Our product assortment includes 25 thousand of cable types. Hipolita Cegielskiego 1
32-400 Myslenice, Poland
Types of Cables

High Voltage cables:

HV XLPE cable with copper wires screen and aluminium laminted foil.
HV XLPE cable with corrugated aluminum sheath.
HV XLPE cable with lead alloy sheath
Leading producer of cables &
cable systems
Marine and Offshore cables
Shipboard instrumentation, control and telecommunication cables
MV Single-core halogen-free shipboard power cables
MV three-core halogen-free shipboard power cables
Shipboard power cables

Oil and Gas / Offshore

BS66883/BS7917 (UKOOA)
NEK606

For enquiries, please contact

BSS Technologies
Plot No: TP010524,
National Industries Park, Jebel Ali
Tel : + 971 4886 7015
Fax : +971 4886 7013
Email : [email protected]

1119R11
 S
TE
IA JEF TECHNO SOLUTIONS PVT. LTD
C
S SO JEF Techno Solutions Pvt. Ltd., an ISO 9001:2015 certified Company, is a pioneer in Asia in the field of EMI/EMC
A studies including Root Cause Analysis, Safety Audits (electrical & fire), Lightning Protection and Grounding
Solutions. We have built a very strong and credible track record of providing effective and reliable solutions for issue
related to grounding, lightning protection, EMI/EMC to various customers. We offer comprehensive solution for Electro-
magnetic Interference & Electromagnetic Compatibility for Oil & Gas, process plants and onshore & offshore installations.
JEF Techno Solutions Pvt. Ltd
We have proven expertise in AC interference study of high voltage transmission lines and buried pipelines -both safety &
HO: No.2, I Floor, 8TH Street,
corrosion problems.
Nandanam Extn., Chennai-600035 TECHNICAL SERVICES
EMI/EMC - For Oil & Gas
Lightning Protection • AC Interference Studies

• DC Interference Studies

• DC Stray Current Analysis

• EM Zoning, Matrix & Evaluation

• Electromagnetic Shielding

• Static & High Frequency Grounding

• Electro Magnetic Isolation

CLASSIC SIGNATURES OF EMI

• Unexplained Tripping
Grounding • Sensor/Valve Maloperation

• Process Interruptions

UNIQUE AUTOMATED SOLUTIONS -For Technical Audits

• Unmatched Accuracy
For enquiries, please contact
BSS Technologies • High Reliability
Plot No: TP010524, • Ultimate Speed
National Industries Park, Jebel Ali
Tel : + 971 4886 7015 • Transparency & Clarity
Fax : +971 4886 7013
Email : [email protected] • Total Flexibility

www.bsstechnologies.com • Consistency & Standardization

1119R11
 A
SS
GGS OIL & GAS SYSTEMS

O
C
IA
TE
GGS is a fully independent system integration company / solution supplier. Specialist in design, production and

S
implementation of complete integrated flow metering solutions for custody transfer gas and LNG projects, worldwide.
GGS can also be your partner in gas filtration, pressure reduction, flow control or gas treatment installations.
As part of the package GGS Oil & Gas Systems can provide turnkey flow metering systems including:

GGS follows a 360°-degree solution driven approach GGS Oil & Gas Systems
• Fully integrated metering skids Onderzeel 6 – 2920 Kalmthout - Belgium
Total commitment; support in every phase of the project
- Flowmeters (Ultrasonic, Coriolis mass, etc)
Project Management
- Valves and piping
Design & Engineering Manufacturing
- Instrumentation (Temperature, pressure, etc) LNG and gas metering systems
• Analyzer solutions with
Calibration &
- Sampling systems Consultancy Feed Single-source Responsibility Integrated tests
From Concept to Completion (FAT)
- Analyser systems
- Density, viscosity
- Gas composition
Training & Service Shipping & Packing
- LNG sampling systems Start-up & Commissioning, SAT
- Mercury analyzer, H2S and Total Sulpher analyzer, Oxigen analyzer
• Supervisory and flow computer systems including flow computers,
control panels and customer interfaces
• Validation and calibration services

From upstream to downstream

GGS Oil & Gas Systems delivers flow metering systems for offshore and onshore locations, from platforms to (off-)loading facilities FSRU
& FNLG, for pipeline operations, and refineries. We work closely with our customers to provide the most cost-effective, highest quality
solutions. Every solution we deliver is a tailor made job; designed, engineered and built based on the customer’s specifications and require-
ments, as well as international industry standards and best practices.

Turnkey solutions from concept to start-up

• Design and engineering
• Project management
• Manufacturing of complete skids
For enquiries, please contact
• Calibration, integrated testing, and certification
BSS Technologies
• Shipping and packing Plot No: TP010524,
• Start-up and commissioning, training and support National Industries Park, Jebel Ali
Tel : + 971 4886 7015
Experienced project engineering Fax : +971 4886 7013
GGS has an experienced in-house team of specialists in mechanical engineering, (flow) instrumentation, electrical engineering and Email : [email protected]
process automation. ( PLC, DCS/ SCADA )
From project definition to engineering and on site installation, quality assurance is the key to any project.

1119R11
 PRODUCTS APPLICATION

IMPRESSED CURRENT ANODES & ACCESSORIES Our Major Activity - Cathodic Protection – involves in all metallic structure buried / immersed in any electrolyte like
Graphite Anodes Platinized Ti/Nb Anodes Soil, Water, Concrete, etc… Structures can be like Pipelines, Tanks, Jetties, Berths, Jackets, Platforms, Reinforced
High Silicon Iron Anodes MMO Coated Titanium Anodes Concrete, etc..
GALVANIC ANODES
Mg Anodes (High & Low potential Cast & Extruded) MAJOR ACTIVITIES/ SERVICES PROVIDED.
Zinc (Soil, Marine, Tank, Pier, Piling, Ribbon, Bracelet Etc)
BSS Tech Offers a wide range of Activities , Surveys and Material / Equipment for the Industry’s Corrosion and Cathodic
Aluminium (Flush Mount, Piling, Bracelet)
Protection requirement
CATHODIC PROTECTION BACKFILL & ACCESSORIES
Petroleum Coke Breeze Backfill Few of The Major Activities We Provide are:
Chemical Backfill Slotted PVC Casing Pipes
Cathodic Protection System Surveys.
Vent Pipes Metallic Casing Pipes etc
POWER SUPPLIES & MONITORING Soil Resistivity Surveys.
Air Cooled & Oil Cooled Transformer Rectifiers
Cathodic Protection System Designs – in accordance to NACE Specifications & Practices, British Standard,
Pulse Rectifiers Solar Power Suppliers
Remote Monitoring & Control Systems. Applicable Industry and Client Requirements.
GROUNDING PRODUCTS
Risk Assessment & Consequence Studies.
Zinc Grounding Cells Zinc Ribbon Anodes
Zinc Mats Grounding Backfills. Formulation of Multilayer Rehabilitation Plans.
Polarization Cell Replacement (Liquid and Solid state)
Computerized Surveys – CIPS, DCVG, Pearson
CABLE & WIRE
HMWPE XLPE/SWA/PVC AC Mitigation Studies and Measures.
HMWPE-HALAR XLPE/PVC
HMWPE-KYNAR(PVDF) Survey Wire etc. Insulating Flange Testing.

CONNECTIONS & ACCESSORIES Interference Testing.

Cable Splice Kits & Accessories Heat Shrink Tubes
Coating Repair material Thermite Weld Material Manufacturing of Corrosion Control, Corrosion Monitoring and Cathodic Protection Equipment / Materials.
Pin Brazing Equipment & Accessories Supply and Installation of Cathodic Protection Systems.
TEST STATIONS & ACCESSORIES
Junction Boxes Magnetic Reed Switches. Testing and Commissioning of Cathodic Protection Systems.
Variable Resistors Shunts
Remote Monitoring and Control Systems.
Cathodic Protection Test Stations Bond boxes
Cathodic Protection Remote Monitoring Test Stations Maintenance Contracts.
REFERENCE ELECTRODES & ACCESSORIES
Coupons Portable & Permanent
Training Programs to Clients in Corrosion Related Subjects.
Copper/Copper Sulphate, Silver/ Silver Chloride, Zinc PRODUCT DEVELOPMENT & RESEARCH
INSTRUMENTS & ACCESSORIES
CP Potential Meter & Equipments CP Test Equipments It is BSS Tech Managements special interest that, a good percentage of our annual profit is invested wisely in the areas of Research
GPS Synchronized Current Interrupters and Developing new Products. These are spend either directly in our facilities or in close co-operation with our raw material suppliers
Pipe & Cable Locators Portable Power Supplies facilities. Our Research & Product Development includes the continuous and extensive search for new materials including the applica-
Survey Equipments Coating Thickness Guages bility and behaviour of existing Material / Equipment for different electrolytes and environments. A wide variety of designs are devel-
Insulation Test Equipments
oped In-House and selected to customer satisfaction, strictly considering the environmental conditions and Material / Equipment
Pipeline Monitoring & Analysis Equipments.
CP Data Recorder/loggers, Soil Resistivity Measuring Equipments are selected with thorough knowledge and fully understanding the properties and behaviour of the products.

1119R11
 GROUP ACTIVITIES
Cathodic Protection & Corrosion Engineering
Anti Fouling
AC / DC Interference and Mitigation Study & Modelling
Coatings & Field Joints
Leak Detection System
Software for Geoinformatics and Water Management
Wireless Remote Monitoring Systems
Electrical Grounding Backfills
Holiday Detection Systems
TR Units & RMCS
Monolithic Isolation Joints
Well Head Remote Monitoring
Pipeline Construction Management System
Construction & Manufacturing
Marine Cathodic Protection
Aluminium & Zinc Casting
Calibration and Certification Services for Test and Measuring Instruments
Downhole Monitoring System
ESP Pumps of Permanent Magnet Motors
Manufacturer of Specialized Industrial Products Based on PU Castings, Foam, Injection Moulding, Blow Moulding & Services
Electric Heat Tracer
High Voltage Cables
Composite Repair Solutions
EMI / EMC Consulting, Lightning Protection & Grounding Solutions
Integrated Flow Metering Solutions for Gas
Gas Flow Measurement & Regulation
1119R11
Notes

1119R11
 SAIT Group

Abu Dhabi Dubai

Dubai Canada India Malaysia Saudi Arabia India Nigeria Kuwait Abu Dhabi India
Abu Dhabi

CAT PRO Tech

AGENTS / DISTRIBUTORS
ASSOCIATE / PARTNERS

Kazakhstan

Wave for
Mining & Petroleum
HEATH Sudan
CONSULTANTS

BS-GIS
Tunisia

Thermopads VP Engineers Sigma

Technical
Service Egypt

Kook Je
Int’l Co. Ltd
Korea

A SAIT GROUP COMPANY

www.bsstechnologies.com 1119R11
Corporate Office
Toronto - Canadian Office
P.O. Box : 33464, Abu Dhabi - U.A.E.
Tel.: +971 2 446 0700
Fax : +971 2 446 0800 Kazakhstan Office
Head Office and Factory
P.O. Box : 52455, Dubai - U.A.E.
Tel.: +971 4 886 7015
Korea office
Fax: +971 4 886 7013
Tunisia Office Syria Office

Kuwait Office
Corporate Office - Abu Dhabi
SAIT GROUP OF COMPANIES Algeria Office
Egypt Office Head Office & Factory - Dubai
Jubail - Saudi office Oman Office
BSS Technologies - Abu Dhabi
Mumbai Office
Yemen Office
BSMC - Dubai - R&D Division
Sudan Office
SSEC - Abu Dhabi Cochin Office
Nigeria Office
KAZ - Saudi Arabia
Malaysia Office
SSE Tech Kuwait W.L.L - Kuwait

SSE Tech - Kochi, India

RACE Tech - Mumbai, India

BSS Tech CP (I) PVT LTD - India

BSS Technologies FZE - Nigeria

BSS Tech - Canada

BSS Tech CP (INTL) SDN. BHD - Malaysia

Own Offices
Satellite Offices

www.bsstechnologies.com
www.corrosion.ae
[email protected]

1119R11