Birla Institute of Technology and Science, Pilani
EEE F341/INSTR F341 Analog Electronics
Second Semester 2021-2022
MID-SEMESTER TEST (OPEN BOOK)
Time: 90 min Max. Marks: 70 Date: 09-03-2022
Note: Assume all op-amps have VSat= ± 10 V, if not mentioned in the question.
[6M]
Q1. (A) Figure shows a differential amplifier based on an Op- Amp.
Suppose that the CMRR of the Op Amp is 100 dB. Assume 4 kΩ input
resistance for the differential amplifier with R1=R2 and R3=10kΩ.
Answer the following:
(i). Differential output voltage.
(ii). Common mode output voltage.
[6M]
Q1. (B). Figure shows an Op Amp based filter circuit. Answer the following: [6 Marks]
(i) Identify the nature of the active filter and its order. For the given circuit,
determine the value of 𝑅1 such that the phase difference between input voltage
and output voltage is equal to ( ) radian. Assume a sine wave input with
π
2
frequency of 5 𝐾𝐻𝑧.
(ii) For the given circuit, determine the phase difference (in degrees) between
𝑉𝑖 and 𝑉𝑜 for 𝑅1 = 100 𝐾Ω.
[9M]
Q1. (C) Figure shows a two op-amps circuit. In the given circuit, assume
𝑅1 = 𝑅3 = 560 Ω and 𝑅𝐹 = 𝑅2 = 5. 6 𝐾Ω. Further, 𝑉𝑖1 =− 2 𝑉 and
𝑉𝑖2 =− 1. 5 𝑉. Suppose that input resistance 𝑅𝑖 = 2 𝑀Ω and the
5
open-loop gain A = 2×10 𝑉/𝑉 for the IC 741 op amp used in the circuit.
Answer the following:
(i). Determine an expression for voltage gain and compute its value.
(ii). Obtain expressions for the input resistances 𝑅𝑖1 and 𝑅𝑖2. Compute their
values.
(iii). Compute the output voltage.
(iv). Identify the type of the amplifier.
[ 10 M ]
Q2. (A) Find the values of the R1, R2,
C1, and C2 components used in the
following circuit to construct a
Butterworth bandpass filter having
lower cutoff at 1kHz and higher cutoff
at 10kHz. Determine the order of the
filter. What is the passband gain?
[8M]
Q2. (B) Find the transfer function of the following circuit and identify the type of operation.
Use R = 10 kΩ and C = 0.01 μF. Draw and label the output waveform Vo(t) for the given input Vi(t)=sin 2000πt .
[ 10 M ]
Q2. (C) Design a KHN circuit to realize a bandpass filter with center frequency of 1 kHz and 3-dB bandwidth of
100 Hz. Use, 22 nF capacitor only. Draw the complete KHN circuit, specifying all the component values. Find the
center frequency gain. Given R1 = R2 = RF = 10 kΩ. [
[ 10 M ]
Q3. (A) Design the following band pass filter to have unity voltage
gain for the pass band from 300Hz to 30KHz. (Consider C2 = 1000pF).
Also, find center frequency (fo) and quality factor (Q).
[ 11 M ]
Q3. (B) Design a V-I based electronic voltmeter to show 2MΩ input impedance and can measure DC voltage
ranges from 0-1V, 0-5V and 0-20V. Use PMMC having full scale deflection (fsd) as 100𝛍A and meter resistance as
2KΩ. Extend the design for similar ranges of input as RMS ac voltage.
