Republic of the Philippines
Department of Education
SCHOOLS DIVISION OF NEGROS ORIENTAL
Siaton II District
Candugay High School
Name: __________________________________ Section: _______________ Score: ___________
SHIELDED METAL ARC WELDING (SMAW) NC-I & II
3rd Quarter Examination
Instruction: Read each statement carefully and identify the correct answer being refer to too. Put your answer
in the space provided before the item number.
___________________1. In preparing the bevel, what is required measurement in the root gap?
___________________2. In preparing the bevel, what is required measurement in the root face?
___________________3. Shielded Metal Arc Welding, in what sector belong the SMAW?
___________________4. In what competencies belong the learning outcome “Receive and responds to
workplace communication?
___________________5. What does AWS mean?
___________________6. How many types of joints do we have?
___________________7. When to perform visual inspection in welding?
___________________8. What PSI stands for?
___________________9. What is the structural Welding codes of SMAW?
___________________10. It is the process in which the metal pieces are joined by heating them to a
suitable temperature to cause them to melt and fuse together a single piece.
_____________________11. What do you call the parts of the Electrode covering the core wire?
_____________________12. What Welding Electrode is being use in Hot pass or filling pass?
_____________________13. What is the main causes of burn through defects?
___________________14. What is the main causes of undercut or no penetration at all?
___________________15. What welding position is being refer too, when the base metal when place over your
body to perform a certain welding?
____________________16. What is the name of the government agency in which they are authorized to
administer all vocational courses and provide National Certificate?
____________________17. What does it mean the first two-digit number in E6011 or E7018?
____________________18. In welding, what position is 1F being implied?
____________________19. What welding electrode being use when performing a root pass?
____________________20. What welding electrode being use when performing a final capping?
_____________________21. Position is performed where the fillet is rotated so that filler material will be
horizontal to the ground. This position is a little harder than the 1F position and normally will qualify you also
in the 1F position.
_____________________22. Position is performed where the fillet weld is rotated so that filler material will be
vertical to the ground. The progression of the weld is normally performed up-hill. This position is harder to
perform than 1F or 2F but normally only qualifies you in the Vertical position and the Flat position.
______________________23. Position is performed where the fillet weld is rotated so that the filler material
will be above you flat with the ground. This position is harder than the previous 1F, 2F, and 3F positions and
will normally qualify you in the 1F and 4F position.
______________________24. What types of measurement when you use inches, meter yard, etc.?
______________________25. What types of measurement when you use milliliter, centimeter, etc.?
______________________26. What will happen to the base metal when to much hot?
______________________27. What will you do prior to welding?
______________________28. How many hours we have in Shielded Metal Arc Welding for NC- I & II to
complete the training duration base on the training regulation in TESDA?
II. Matching type: Direction: Match column A to column B Write the letter of the correct answer
only.
A. Uses/Applications B. Tools/Materials
_____1. Measures weld profile a. 1/8” or 3.2 Electrode size
_____2. Bakes or pre-heat electrodes b. Portable oven
_____3. Remove slag/spatters c. chipping hammer
_____4.Protect hands from heat/spatters/radiation d. Leather/Welding gloves
_____5. Use to protect eyes when chipping slag e. Welding Shield/Helmet
_____6. Used as joint spacer f. Leather Apron
_____7. Protect the face and eyes from arc rays g. Safety goggles
_____8. Used to protection from sparks/hot metal h. Cover all
_____9. Complete protection of the whole body during welding i. Weld gauge
_____10.Use to protect workers falling object to the foot j. Safety shoes
Answer key
1. 1/8”
2. 1/8”
3. Metal & Engineering
4. Basic
5. American Welding Society
6. Five
7. After welding
8. Pounds per square inch
9. AWS D 1.1
10. Welding
11. Flux covering
12. E6012/13
13. High Current
14. Low current
15. Overhead position/4g
16. Technical Education and Skills Development Authority
17. Tensile strength in thousand
18. Flat position
19. E6011
20. E7018
21. Horizontal position
22. Vertical Position
23. Overhead Position
24. English System
25. Metric System
26. Deform
27. Safety first or Use PPE
28. 268 hrs
II.
1. I
2. B
3. C
4. D
5. G
6. A
7. E
8. F
9. H
10. J
CANDUGAY HIGH SCHOOL
SCHOOLS DIVISION OF NEGROS ORIENTAL
Siaton 2 District
Siaton, Negros Oriental
Table of Specifications in SMAW 11
Third Quarter- First Cycle
S.Y 2022-2023
Learning Competency/ies Content Number Knowledge Comprehensio Application Analysis Synthesis Evaluation Item Percentag
/topic of Items n Placement e
1. 12 1-12 25%
2. 12 13-24 25%
3. 12 25-36 25%
4. 12 37-48 25%
Total 48 48 100%
Prepared by: ISAGANI B. ABRIL
Grade-11 SMAW Adviser
Noted by: PRIMA G. EBIDA
TIC
