[Link]-es.
org | (800) 423-6587 | (562) 699-0543 A Subsidiary of the International Code Council ®
ICC-ES Evaluation Report Reissued December 2021
ESR-4108 Revised April 2022
This report is subject to renewal December 2023.
DIVISION: 08 00 00—OPENINGS specific conditions, and the verification of those conditions
Section: 08 62 00—Unit Skylights is outside the scope of this report. These codes or standards
often provide supplemental information as guidance.
REPORT HOLDER:
3.0 DESCRIPTION
VELUX AMERICA LLC 3.1 Single Dynamic Domes:
The VELUX CDS Single Dynamic Domes consist of a single
EVALUATION SUBJECT:
geometric-shaped plastic dome factory-attached to an
aluminum extruded frame with an aluminum extruded
VELUX® DYNAMIC DOME SKYLIGHTS retainer cap.
1.0 EVALUATION SCOPE The frame and retainer cap is manufactured from
0.06-inch-thick (1.52 mm) 6063-T5 or 6063-T6 aluminum.
1.1 Compliance with the following codes: See Figure 1.
2021, 2018, 2015 and 2012 International Building Code The plastic dome is manufactured from a translucent-
(IBC) white polycarbonate panel with a uniform thickness of
2021, 2018, 2015 and 2012 International Residential 0.118 inch (3.00 mm). The panel is recognized as Plaskolite,
Code (IRC) LLC’s Tuffak® SK1 under ESR-2728.
Properties evaluated: 3.2 Double Dynamic Domes:
Structural The VELUX CMD2 Double Dynamic Domes consist of
double geometric-shaped plastic domes factory-attached to
Air infiltration frame as shown in Figure 2.
Water penetration resistance The frame and dome clamp is manufactured from
Durability 0.06-inch-thick (1.52 mm) 6063-T6 aluminum. See
Figure 2.
1.2 Evaluation to the following green standard:
The outer plastic dome is manufactured from a
2020, 2015 and 2012 ICC 700 National Green Building translucent-white or clear polycarbonate panel with a
Standard™ (ICC700-2020, ICC 700-2015 and ICC 700- uniform thickness of 0.118 inch (3.00 mm).
2012)
The inner plastic dome is manufactured from a
Attributes verified: translucent-white or clear polycarbonate panel with one side
See Section 2.0. prismatic with a thinnest thickness of 0.053 inch (overall
thickness of 0.118-inch). The prismatic side faces the
2.0 USES
exterior.
The VELUX Dynamic Dome Skylights are non-operable
The panels are recognized as Plaskolite, LLC’s Tuffak®
plastic-glazed unit skylights complying with IBC Sections
SK1 (outer) and SK (inner) under ESR-2728.
2405 and 2610 and IRC Section R308.6.
4.0 DESIGN AND INSTALLATION
The attributes of the skylights have been verified as
conforming to the requirements of (i) ICC700-2020 Section 4.1 Design:
[Link] and [Link].4; ICC 700-2015 Section 4.1.1 Performance Grade: The performance grade (PG)
[Link] and [Link].4; and ICC 700-2012 Section ratings are provided in Tables 1 and 2.
[Link] and [Link].3 for fenestration air leakage.
Note that decisions on compliance for those areas rest with 4.1.2 Air Infiltration: When tested at an air pressure
the user of this report. The user is advised of the project- differential of 1.57 psf (75 Pa), the skylights have an air
specific provisions that may be contingent upon meeting leakage rate of less than 0.30 cfm/ft2 (1.5 L/s*m2).
ICC-ES Evaluation Reports are not to be construed as representing aesthetics or any other attributes not specifically addressed, nor are they to be construed
as an endorsement of the subject of the report or a recommendation for its use. There is no warranty by ICC Evaluation Service, LLC, express or implied, as
to any finding or other matter in this report, or as to any product covered by the report.
Copyright © 2022 ICC Evaluation Service, LLC. All rights reserved. Page 1 of 8
ESR-4108 | Most Widely Accepted and Trusted Page 2 of 8
4.2 Installation: 5.4 The use of the skylights as components of fire-
resistance-rated assemblies is outside the scope of
The skylight must be attached with minimum No. 8
this report.
corrosion-resistant wood screws in each mounting hole
provided in the skylight frame, with the screw length being 5.5 The attachment of the curbs to the supporting structure
sufficient to penetrate a wood curb a minimum of 1 inch is outside the scope of this report.
(25 mm). See Tables 1 and 2 for the required number of
5.6 The use of skylights in wind-borne debris regions is
fasteners. Additional installation details are provided in
outside the scope of this report.
Figures 1 and 2.
5.7 The skylights are manufactured in Greenwood, South
The skylights are curb-mounted and must be installed on
Carolina under a quality control program with
a minimum 2-by lumber with a minimum specific gravity of
inspections by ICC-ES.
0.42, sized to the inside dimension noted in Table 1, and of
a height sufficient so that the plastic glazing is a minimum of 6.0 EVIDENCE SUBMITTED
4 inches (102 mm) above the plane of the roof. The wood
Data in accordance with the ICC-ES Acceptance Criteria for
curb and its attachment to the roof structure must be
Plastic-Glazed Skylights (AC16), dated April 2020
designed to resist wind uplift and gravity loads.
(Editorially revised August 2020).
Flashing must comply with, and be installed in accordance
7.0 IDENTIFICATION
with, IBC Section 1507 or IRC Section R905, as applicable.
7.1 The skylights are labeled with the VELUX name and
5.0 CONDITIONS OF USE
address; the Single Dynamic Dome or Double
The VELUX Dynamic Dome Skylights described in this Dynamic Dome series; the model number and the
report comply with, or are suitable alternatives to what is product designation (SKP-PG30); the evaluation report
specified in, those codes listed in Section 1.0 of this report, number (ESR-4108); and a safety label complying with
subject to the following conditions: Class I, ANSI Z 35.1-1972 (warning of risk of falling).
5.1 The skylights must be installed in accordance with this 7.2 The report holder’s contact information is the following:
report, Sections 2405.4 and 2610 of the IBC or Section
VELUX AMERICA LLC
R308.6 of the IRC, as applicable, and the
POST OFFICE BOX 5001
manufacturer’s published installation instructions. In
GREENWOOD, SOUTH CAROLINA 29648
the event of a conflict between this report and the
(864) 941-5360
manufacturer’s published installation instructions, this
[Link]
report governs.
[Link]@[Link]
5.2 The design pressure (performance grades) for the commercialteam@[Link]
skylights are as set forth in Table 1 and Table 2, and
must be used with the load combinations of the
applicable code.
5.3 The manufacturer’s installation instructions must be
available at the jobsite during installation.
TABLE 1—SINGLE DYNAMIC DOME SKYLIGHTS
NUMBER OF NUMBER OF PERFORMANCE GRADE (PG)6 (psf)
1,2,3 DOME RISE
MODEL NO. RETAINER MOUNTING PGpos PGneg
(inches)
FASTENERS4 FASTENERS5 (inward forces) (outward forces)
CDS 4896 3P200 24 24
15 30 30
CDS 4848 3P200 16 16
For SI: 1 inch = 25.4 mm, 1 psf = 47.88 Pa
1.
CDS = mill-finished frame
2.
The numbers in the middle are the nominal inside curb dimensions in inches, width by length.
3.
3P200 = white polycarbonate dome
4.
The retainer fasteners must be #10 by 5/8"-long pan head screws. The screws must not be spaced greater than 71/2" from the corners nor 12" o.c.
5.
The mounting fasteners must be #8 by 13/4"-long pan head screws. The screws must not be spaced greater than 81/2" from the corners nor 12" o.c.
6.
Production designation = SKP-PG30
ESR-4108 | Most Widely Accepted and Trusted Page 3 of 8
(SK1)
INSIDE CURB
RIBS
DIMENSIONS
FIGURE 1A—SINGLE DYNAMIC DOME CDS 4896 3P200 6
CDS 4848 3P200 2
FIGURE 1B—SINGLE DYNAMIC DOME SIDE AND TOP
VIEWS FOR 48-INCH-WIDE SKYLIGHTS
ESR-4108 | Most Widely Accepted and Trusted Page 4 of 8
TABLE 2—DOUBLE DYNAMIC DOME SKYLIGHTS
DOME RISE PERFORMANCE
(inches) NUMBER OF NUMBER OF GRADE (PG)5 (psf)
MODEL NO. 1,2 RETAINER MOUNTING PGpos PGneg
INNER OUTER FASTENERS3 FASTENERS4 (inward (outward
forces) forces)
CMD2 4896 P1C1 24 24
CMD2 4872 P1C1 20 20
14 15
CMD2 4860 P1C1 18 18
CMD2 4848 P1C1 16 16
CMD2 4783 P1C1 13 14 22 22
CMD2 3696 P1C1 22 22 30 30
CMD2 3672 P1C1 18 18
103/8 113/8
CMD2 3660 P1C1 16 16
CMD2 3636 P1C1 12 12
CMD2 2496 P1C1 5 5
20 20
6 /8 7 /8
CMD2 2448 P1C1 12 12
CMD2 4896 P1C2 24 24
CMD2 4872 P1C2 20 20
14 15
CMD2 4860 P1C2 18 18
CMD2 4848 P1C2 16 16
CMD2 4783 P1C2 13 14 22 22
CMD2 3696 P1C2 22 22 30 30
CMD2 3672 P1C2 3 3
18 18
10 /8 11 /8
CMD2 3660 P1C2 16 16
CMD2 3636 P1C2 12 12
CMD2 2496 P1C2 20 20
65/8 75/8
CMD2 2448 P1C2 12 12
CMD2 4896 P2C1 24 24
CMD2 4872 P2C1 20 20
14 15
CMD2 4860 P2C1 18 18
CMD2 4848 P2C1 16 16
CMD2 4783 P2C1 13 14 22 22
CMD2 3696 P2C1 22 22 30 30
CMD2 3672 P2C1 3 3
18 18
10 /8 11 /8
CMD2 3660 P2C1 16 16
CMD2 3636 P2C1 12 12
CMD2 2496 P2C1 20 20
65/8 75/8
CMD2 2448 P2C1 12 12
For SI: 1 inch = 25.4 mm, 1 psf = 47.88 Pa
1.
The numbers in the middle are the inside curb dimensions in inches, width by length.
2.
P1C1 = clear outer dome / clear inner dome with a prismatic side;
P1C2 = clear outer dome / white inner dome with a prismatic side;
P2C1 = white outer dome / clear inner dome with a prismatic side
3.
The retainer fasteners must be SST #10-16 x 5/8” AB tapping screws with six lobe truss head. The screws must not be spaced
greater than 8" from the corners nor 12" o.c..
4.
The mounting fasteners must be #8 by 13/4"-long flat head screws. The screws must not be spaced greater than 81/2" from the
corners nor 12" o.c.
5.
Production designation = SKP-PG30
ESR-4108 | Most Widely Accepted and Trusted Page 5 of 8
FIGURE 2A—DOUBLE DYNAMIC DOME
INSIDE CURB
RIBS
DIMENSIONS
4848 2
3636 0
FIGURE 2B—DOUBLE DYNAMIC DOMES SIDE AND TOP VIEWS FOR SQUARE SKYLIGHTS
ESR-4108 | Most Widely Accepted and Trusted Page 6 of 8
INSIDE CURB
RIBS
DIMENSIONS
4896 6
4783 5
4872 4
4860 3
FIGURE 2C—DOUBLE DYNAMIC DOMES SIDE AND TOP VIEWS FOR 48-INCH-WIDE RECTANGULAR SKYLIGHTS
INSIDE CURB
RIBS
DIMENSIONS
3696 5
3672 3
3660 2
FIGURE 2D—DOUBLE DYNAMIC DOMES SIDE AND TOP VIEWS FOR 36-INCH-WIDE RECTANGULAR SKYLIGHTS
INSIDE CURB
RIBS
DIMENSIONS
2496 6
2448 2
FIGURE 2E—DOUBLE DYNAMIC DOMES SIDE AND TOP VIEW FOR 24-INCH-WIDE RECTANGULAR SKYLIGHTS
ICC-ES Evaluation Report ESR-4108 CBC and CRC Supplement
Reissued December 2021
Revised April 2022
This report is subject to renewal December 2023.
[Link] | (800) 423-6587 | (562) 699-0543 A Subsidiary of the International Code Council ®
DIVISION: 08 00 00—OPENINGS
Section: 08 62 00—Unit Skylights
REPORT HOLDER:
VELUX AMERICA LLC
EVALUATION SUBJECT:
VELUX® DYNAMIC DOME SKYLIGHTS
1.0 REPORT PURPOSE AND SCOPE
Purpose:
The purpose of this evaluation report supplement is to indicate that VELUX® Dynamic Dome Skylights, described in ICC-ES
evaluation report ESR-4108, have also been evaluated for compliance with the codes noted below.
Applicable code editions:
2019 California Building Code® (CBC)
For evaluation of applicable chapters adopted by the California Office of Statewide Health Planning and Development
(OSHPD) and Division of State Architect (DSA), see Sections 2.1.1 and 2.1.2 below.
2019 California Residential Code® (CRC)
2.0 CONCLUSIONS
2.1 CBC:
The VELUX® Dynamic Dome Skylights described in Sections 2.0 through 7.0 of the evaluation report ESR-4108, comply with
CBC Sections 2405 and 2610, provided the design and installation are in accordance with the 2018 International Building
Code® (IBC) provisions noted in the evaluation report and the additional requirements of CBC Chapters 24 and 26, as
applicable.
2.1.1 OSHPD:
The applicable OSHPD Sections of the CBC are beyond the scope of this supplement.
2.1.2 DSA:
The applicable DSA Sections of the CBC are beyond the scope of this supplement.
2.1 CRC:
The VELUX® Dynamic Dome Skylights, described in Sections 2.0 through 7.0 of the evaluation report ESR-4108, comply
with CRC Section R308.6, provided the design and installation are in accordance with the 2018 International Residential
Code® (IRC) provisions noted in the evaluation report.
This supplement expires concurrently with the evaluation report, reissued December 2021 and revised April 2022.
ICC-ES Evaluation Reports are not to be construed as representing aesthetics or any other attributes not specifically addressed, nor are they to be
construed as an endorsement of the subject of the report or a recommendation for its use. There is no warranty by ICC Evaluation Service, LLC, express
or implied, as to any finding or other matter in this report, or as to any product covered by the report.
Copyright © 2022 ICC Evaluation Service, LLC. All rights reserved. Page 7 of 8
ICC-ES Evaluation Report ESR-4108 FBC and FRC Supplement
Reissued December 2021
Revised April 2022
This report is subject to renewal December 2023.
[Link] | (800) 423-6587 | (562) 699-0543 A Subsidiary of the International Code Council ®
DIVISION: 08 00 00—OPENINGS
Section: 08 62 00—Unit Skylights
REPORT HOLDER:
VELUX AMERICA LLC
EVALUATION SUBJECT:
VELUX® DYNAMIC DOME SKYLIGHTS
1.0 REPORT PURPOSE AND SCOPE
Purpose:
The purpose of this evaluation report supplement is to indicate that VELUX Dynamic Dome Skylights, described in ICC-ES
evaluation report ESR-4108, have also been evaluated for compliance with the codes noted below.
Applicable code editions:
2020 Florida Building Code—Building
2020 Florida Building Code—Residential
2.0 CONCLUSIONS
The VELUX Dynamic Dome Skylights, described in Sections 2.0 through 7.0 of the evaluation report ESR-4108, comply with
the Florida Building Code—Building and Florida Building Code—Residential, provided the design requirements are
determined in accordance with the Florida Building Code—Building and Florida Building Code—Residential. The installation
requirements noted in ICC-ES evaluation report ESR-4108 for the 2018 International Building Code® meet the requirements
of the Florida Building Code—Building or the Florida Building Code—Residential with the following condition:
Use of VELUX Dynamic Dome Skylights in wind-borne debris regions is outside the scope of this supplement.
Use of the VELUX Dynamic Dome Skylights for compliance with the High-Velocity Hurricane Zone provisions of the Florida
Building Code—Building and Florida Building Code—Residential has not been evaluated and is outside the scope of this
supplemental report.
For products falling under Florida Rule 61G20-3, verification that the report holder’s quality assurance program is audited
by a quality assurance entity approved by the Florida Building Commission for the type of inspections being conducted is the
responsibility of an approved validation entity (or the code official, when the report holder does not possess an approval by
the Commission).
This supplement expires concurrently with the evaluation report, reissued December 2021 and revised April 2022.
ICC-ES Evaluation Reports are not to be construed as representing aesthetics or any other attributes not specifically addressed, nor are they to be
construed as an endorsement of the subject of the report or a recommendation for its use. There is no warranty by ICC Evaluation Service, LLC, express
or implied, as to any finding or other matter in this report, or as to any product covered by the report.
Copyright © 2022 ICC Evaluation Service, LLC. All rights reserved. Page 8 of 8
