1 STRUCTURAL NOTES

S-01
MATERIALS : 5.0 CONCRETE MASONRY UNITS (CMU)
3.1 NORMAL WEIGHT CONCRETE :
GENERAL NOTES: 5.1 CMU USED IN THESE WORKS SHALL HAVE A MINIMUM ULTIMATE
COMPRESSIVE STRENGTH @ 28 DAYS AS FOLLOWS :
3.1.1 CONCRETE USED IN THIS WORK SHALL HAVE A MINIMUM COMPRESSIVE STRENGTH
1.0 GENERAL : 100mm THICK NON-LOAD BEARING CMU, f'm = 2.4 MPa (350 PSI)
@ 28 DAYS AS FOLLOWS:
150mm THICK NON-LOAD BEARING CMU, f'm = 2.4 MPa (350 PSI)
1.1 UNLESS NOTED OTHERWISE, ALL DIMENSIONS SHOWN ARE IN METERS COLUMN, BEAM, SLAB, & OTHERS fc' = 28MPa (4,000 PSI) 5.2 ALL CELLS SHALL BE SOLIDLY FILLED WITH GROUT. CONCRETE SHALL
1.2 THE CONTRACTOR SHALL VERIFY ALL DIMENSIONS AND CONDITIONS AT THE FOOTING fc' = 21MPa (3,000 PSI) HAVE A MINIMUM COMPRESSIVE STRENGTH OF 13.80 MPa
SITE, AND SHALL NOTIFY THE ENGINEER OF DISCREPANCIES BETWEEN ACTUAL (2,000 PSI) @ 28 DAYS.
CONDITIONS AND INFORMATION SHOWN ON THE DRAWINGS BEFORE PROCEEDING 3.1.2 ALL CONCRETE SHALL BE DEPOSITED, VIBRATED AND CURED IN ACCORDANCE
WITH THE WORK. THIS SHALL INCLUDE THE LOCATION AND DIMENSIONS OF
GROOVES, REGLETS, SLEEVES, CURBS, OPENINGS, EMBEDDED OR ATTACHED
WITH ACI STANDARD 318-2005. 5.3 UNLESS INDICATED OTHERWISE, CMU REINFORCEMENT SHALL BE 10mmØ
ITEMS, ETC. (REFER TO ARCHITECTURAL, MECHANICAL, ELECTRICAL AND PLUMBING.) 3.1.3 MINIMUM CONCRETE COVER FOR REINFORCING BARS SHALL BE AS FOLLOWS: HOR. BARS SPACED @ 600mm AND 10mmØ VERT. BARS SPACED @ 600mm.
1.3 ALL FIGURED DIMENSIONS SHALL TAKE PRECEDENCE OVER SCALE SHOWN ON PLANS,
A. FOOTINGS & BOT. OF FOOTING TIE BEAM = 75mm (CAST AGAINST EARTH) 5.4 ALL WALLS SHALL BE CONSTRUCTED IN CONVENTIONAL RUNNING BOND,
SECTIONS OR DETAILS. SPECIFIC NOTES AND DETAILS ON DRAWINGS SHALL TAKE B. BEAMS AND COLUMNS = 40mm (TO STIRRUPS AND TIES) UNLESS NOTED OTHERWISE.
PRECEDENCE OVER GENERAL NOTES AND TYPICAL DETAILS. C. SLABS AND WALLS = 20mm (CAST AGAINST FORMS) 5.5 GROUT MASONRY IN 2.4m MAXIMUM LIFTS. REINFORCING SHALL BE
1.4 THE STRUCTURAL DRAWINGS AND SPECIFICATIONS REPRESENT THE FINISHED 3.1.4 BEFORE CONCRETE IS POURED, CHECK WITH ALL TRADES TO ENSURE PROPER SECURED AGAINTS DISPLACEMENT PRIOR TO GROUTING BY WIRE
STRUCTURES. THEY DO NOT INDICATE THE METHOD OF CONSTRUCTION PLACEMENT OF ALL OPENINGS, SLEEVES, CURBS, CONDUITS, ETC. RELATIVE TO POSITIONERS AT INTERVALS NOT EXCEEDING 200 BAR DIAMETERS
UNLESS SO STATED. THE CONTRACTOR SHALL PROVIDE ALL NECESSARY
MEASURES TO PROTECT THE STRUCTURES, ADJACENT PROPERTIES, WORKMEN THE WORK. NOR 3m.
AND OTHER PERSONS DURING ALL PHASES OF CONSTRUCTION. 5.6 IF WORK IS STOPPED ONE (1) HOUR OR LONGER, PROVIDE HORIZONTAL
1.5 THE CONTRACTOR SHALL IMMEDIATELY NOTIFY THE ENGINEER IN CHARGE
OF ANY CONDITION WHICH IN HIS OPINION MIGHT ENDANGER THE STABILITY
NOTES ON REINFORCING STEEL BARS CONSTRUCTION JOINTS BY STOPPING THE GROUT 50mm BELOW THE TOP
OF THE BLOCK.
OF THE STRUCTURES OR CAUSE DISTRESS IN THE STRUCTURES. 3.2 ALL REINFORCING STEEL BARS SHALL BE NEW BILLET, HOT ROLLED, WELDABLE, DEFORMED BARS
1.6 THE CONTRACTOR SHALL PROVIDE TEMPORARY ERECTION BRACINGS AND CONFORMING TO THE SPECIFICATIONS OF PNS 49: 1986 (ASTM 615) , AND ASTM A706 (GR. 60,
SHORINGS FOR ALL THE STRUCTURAL MEMBERS AS REQUIRED FOR STRUCTURE
STABILITY DURING ALL PHASES OF CONSTRUCTION.
WELDABLE) WHOSE GRADE IS SHOWN IN TABLE 1. LAP SPLICE & ANCHORAGE LENGTH TABLE
STANDARD HOOK LAP SPLICE (m) MIN. LAP SPLICE
1.7 THE CONTRACTOR SHALL TAKE ALL STEPS NECESSARY TO ENSURE THE UNIT LENGTH OF COL. REINF.
PROPER ALIGNMENT OF THE STRUCTURES DURING AND AFTER THE INSTALLATION TABLE 1 BAR
DIAMETER
ANCHORAGE
LENGTH (m) TENSION BAR COMP. BAR WEIGHT INDIVIDUAL BARS
(mm) (m) (kg/m)
OF ALL STRUCTURAL AND FINISH MATERIALS.
90° 180° 135° TOP BAR OTHERS TOP BAR OTHERS W/ TIES W/ SPIRAL
GRADE BAR DIAMETER
1.8 THE CONTRACTOR SHALL INFORM THE SUB-CONTRACTORS THAT NO CONSTRUCTION 10 0.50 0.15 0.13 0.10 0.42 0.30 0.42 0.30 0.617 0.30 0.30
MATERIALS SHALL BE STORED ON POURED FLOORS, AND SHALL ENSURE THAT THE
SUB-CONTRACTORS DO NOT VIOLATE THIS IMPORTANT REQUIREMENT. GRADE 415 (fy = 60 ksi) 20, 25, 28, 32, & 36 mm 12 0.50 0.20 0.15 0.12 0.42 0.30 0.42 0.30 0.889 0.30 0.30
16 0.60 0.25 0.18 0.14 0.73 0.52 0.87 0.62 1.580 0.52 0.47

CONCRETE NOTES: GRADE 275 (fy = 40 ksi) 10, 12, & 16 mm 20 0.60 0.30 0.20 0.20 0.91 0.65 1.10 0.78 2.469 0.65 0.58
25 0.68 0.40 0.28 0.26 1.15 0.82 1.40 1.00 3.858 0.80 0.73
ACI 318: THE AMERICAN CONCRETE INSTITUTE BUILDING CODE OR THE MINIMUM REQUIREMENTS OF THE
NATIONAL STRUCTURAL CODE OF THE PHILIPPINES (NSCP) 2010 SHALL BE COMPLIED WITH FOR ALL WORK, GRADE 228 (fy = 33 ksi) SMALLER THAN 10 mm 28 0.86 0.48 0.38 - 1.45 1.03 1.53 1.09 4.840 0.90 0.82
EXCEPT AS MODIFIED HEREIN. 32 1.12 0.56 0.43 - 1.90 1.35 1.74 1.24 6.327 1.03 0.93
36 1.43 0.61 0.48 - 2.40 1.70 2.00 1.40 8.00 1.20 1.05
2.1 IN THE EVENT THAT RELOCATION IS NOT POSSIBLE, THE STRUCTURAL ENGINEERING MUST FIRST APPROVE
THE PROPOSED LOCATION. CONSTRUCTION JOINTS MUST BE PLACED WITHIN THE MIDDLE THIRD OF THE SPANS 3.3 THE SUPPLEMENTARY REQUIREMENTS OF WELDABLE DEFORMED REBARS SHALL BE AS FOLLOWS:
OF SLABS, BEAMS, AND GIRDERS. A. THE MAXIMUM YIELD STRENGTH OF WELDABLE BARS - 540 Mpa. NOTES:
1. ACI SECTION 12.4 STATES THAT DEVELOPMENT LENGTH OF INDIVIDUAL BARS W/IN A BUNDLE,
B. THE TENSILE STRENGTH SHALL NOT BE LESS THAN 1.25 TIMES THE ACTUAL YIELD STRENGTH. IN TENSION OR COMPRESSION, SHALL BE THAT FOR THE INDIVIDUAL BAR, INCREASED 20%
2.2 UNLESS SPECIFICALLY INDICATES, PIPES OR DRAINS THAT ARE THICKER THAN ONE-THIRD OF A SLAB OR WALL COLUMN/WALL
CANNOT BE PLACED IN STRUCTURAL CONCRETE.
3.4 ALL CONCRETE REINFORCEMENT SHALL BE DETAILED, FABRICATED, LABELED, SUPPORTED AND FOR THREE BAR BUNDLE, AND 33% FOR FOUR BAR BUNDLE. ANCHORAGE
FACE LENGTH
2. FOR COLUMNS, AT ANY LEVEL NO MORE THAN ALTERNATE BARS SHOULD BE SPLICED. NOT
SPACED IN FORMS, SECURED IN THE REQUIRED LOCATION IN ACCORDANCE WITH THE PROCEDURES MORE THAN 33% OF THE BARS SHALL BE SPLICED W/IN THE REQUIRED LAP LENGTH.
2.3 BAR PLACEMENT AND SUPPORTS MUST ACCORD WITH THE RECOMMENDED ACI PRACTICE; REINFORCING
BARS, ANCHOR BOLTS, AND OTHER INSERTS MUST BE SECURED IN PLACE PRIOR TO POURING CONCRETE. AND STANDARD PRACTICE FOR DETAILING REINFORCED CONCRETE STRUCTURES, ACI - 315. MINIMUM DISTANCE BETWEEN TWO ADJACENT BAR SPLICES SHALL BE 600mm. 180°
3. TOP BARS ARE HORIZONTAL BARS W/ MORE THAN 300mm DEPTH OF CONCRETE CAST BELOW HOOK
3.5 ALL REINFORCING BARS SHALL BE CLEANED THOROUGHLY OF ALL LOOSE RUST, SOIL OR OTHER THE REINFORCEMENT.
2.4 ALL INSERTS, ANCHOR BOLTS, ETC. TO BE EMBEDDED IN THE CONCRETE SHALL BE HOT DIP GALVANIZED 135°
UNLESS MATERIAL IMMEDIATELY PRIOR TO PLACING CONCRETE. 4. AS MUCH AS POSSIBLE, SPLICES SUBJECTED TO TENSILE STRESSES ARE DISCOURAGE, THESE HOOK 90°
SHOULD BE AVOIDED OR PROVIDED W/ STANDARD HOOKS.
NOTED OTHERWISE. HOOK
4.0 UNLESS SHOWN OTHERWISE ON PLANS, SPLICES SHALL BE AS FOLLOWS :
2.5 IN GENERAL, THE LATEST EDITION OF THE MANUAL OF STANDARD PRACTICE FOR DETAILING CONCRETE
STRUCTURES, ACI 315, SHALL BE ADHERED TO, UNLESS SHOWN OTHERWISE.
A. BEAMS AND FOOTING TIE BEAMS : TOP AND BOTTOM BARS SHALL NOT
BE SPLICED WITHIN THE COLUMN OR WITHIN A DISTANCE OF TWICE THE
2.6 ADDITION OF WATER TO CONCRETE AT JOB SITE IS NOT ALLOWED, BUT USE OF ADMIXTURES TO PRODUCE MEMBER DEPTH FROM THE FACE OF THE COLUMN ; AT LEAST TWO EXTRA
PROPER SLUMP AND WORKABILITY IS SUBJECT TO THE ENGINEER'S APPROVAL. STIRRUP - TIES SHALL BE PROVIDED AT ALL SPLICES.
2.7 SET UP AND SUBMIT THE CONCRETE MIX DESIGN, INCLUDING THE RESULTS OF THE CYLINDER STRENGTH B. COLUMNS : SPLICES WHEN PERMITTED SHALL BE MADE WITHIN THE CENTER
TEST, THE WATER AND CEMENT CONTENTS, AND THE AGGREGATES GRADATION, FOR REVIEW. HALF OF COLUMN HEIGHT, AND LAP SPLICE SHALL NOT BE LESS THAN
SIZE OF AGGREGATES TO BE USED: 40 BAR DIAMETERS. THE USE OF APPROVED MECHANICAL DEVICES MAY BE
PERMITTED PROVIDED THAT NOT MORE THAN ALTERNATE BARS ARE
SPLICED AT ANY LEVEL AND THE MINIMUM VERTICAL DISTANCE
BETWEEN TWO ADJACENT BAR SPLICES SHALL BE 600mm.
C. CONCRETE MASONRY UNIT (CMU) WALLS : VERTICAL BARS SHALL BE SPLICED
AT THE TOP OF WALL FOOTING OR TIE BEAM AND AT THE BOTTOM OF RC LINTEL
BEAM OR BEAMS. SPLICE LENGTHS SHALL BE 600mm MIN.

4.1 UNLESS INDICATED OTHERWISE, ALL BEAMS TERMINATING AT THE COLUMN

SHALL HAVE TOP AND BOTTOM BARS EXTENDING TO THE FAR FACE OF
THE COLUMN, TERMINATING IN A STANDARD 90° HOOK LENGTH OF
ANCHORAGE NOT LESS THAN 600mm.

4.2 SHOP DRAWINGS FOR BENDING AND CUTTING OF REINFORCEMENT SHALL

BE SUBMITTED FOR APPROVAL TO THE ENGINEER PRIOR TO FABRICATION.
4.3 SPLICE LENGTH OF REINFORCING BARS SHALL BE AS SHOWN IN THE TABLE
ABOVE.

R.A. 544 DESIGNER/ CONSULTANT: PROJECT TITLE: OWNER: DRAFTED BY: K.P.P. DATE: SHEET CONTENT: SHEET NO.
KEENUPOWER ALL DOCUMENTS PREPARED
KEENU PAUL PAULO CHECKED BY: S.C.C. DATE:
BUILDERS
AND FURNISHED ARE THE
PROPERTY OF THE ENGINEER
ARE NOT TO BE USED OR
CIVIL ENGINEER TWO STOREY RESIDENCE SUSAN FORD & GREGORIO APPROVED BY: S.C.C. DATE:
AS SHOWN
S
Carmen, Rosales, Pangasinan
Tel. No. 075-235161 Smart: 09693572413 REPRODUCED WITHOUT THE PRC REQ NO: TIN NO: PILLAR REV. NO: DATE:
WRITTEN AGREEMENT WITH
THE ENGINEER.
PTR NO: DATE: #044 FIRETREE ST. BRGY. TORRES, MAPANDAN, PANGASINAN
OWNER/CLIENT
DRWG. NO: 1 6
 A B c C D
13.010 DOWEL BARS TO
2.001 4.550 4.459 2.000 MATCH CHB
VERT. BARS 12mm Ø @800 V.B.
3.409 1.581 1.469 12mm Ø @600 H.B.
FTB 3 - 10mm Ø FFL
BOT. BARS

200
12mm Ø BOT.

3.001
3.001

FTB
NGL
BARS @ 300 O.C.

25 db
1
WF F1C1 F1C1
F1C1 WF

650 (min)
F1C1 FTB

2.100

250
WF SECTION 3 - 10mm Ø
BOT. BARS
12mm Ø
5.600

5.600
FTB
WF WF BOT. BARS
FTB
10MM DIA RSB SPACED 400 @ 300 O.C.

3.500
@ 0.60M O.C BOTHWAYS
(TYPICAL TO ALL
SLABS GROUND FLOOR)

2 F1C1
WF F1C1 F1C1
2 WALL-FOOTING DETAIL
F1C1 FTB

1.800
S-02
WF 300
15.800

C-1
4.501

23.000
FTB FTB

400
4.500
8 - 16 mm dia. RSB
3' F1C1
8 - 16 mm dia. Vertical O.C spaced equally
1.800

F1C1 FTB WF
Bars
3 FTB
F1C1 F1C1
1200

10 mm. dia. Stirrups

FTB FTB
4.000

1 at 50mm, 2 at 100mm,
2 at 150mm, rest at
FTB
200mm O.C.
4 F1C1

8.000
FTB

1200
F1C1 WF F1C1

FTB FTB
4.000

1800.00 mm
FTB
PLAN
WF
F1C2 F1C2
F1 C1

300
2.400 4.209 2.000
50 mm THICK
2.000 4.791 6.209 GRAVEL BED SECTION
13.000

1 FOUNDATION PLAN 3 COLUMN-FOOTING DETAILS

S-02 S-02

R.A. 544 DESIGNER/ CONSULTANT: PROJECT TITLE: OWNER: DRAFTED BY: K.P.P. DATE: SHEET CONTENT: SHEET NO.
KEENUPOWER ALL DOCUMENTS PREPARED
KEENU PAUL PAULO CHECKED BY: S.C.C. DATE:
BUILDERS
AND FURNISHED ARE THE
PROPERTY OF THE ENGINEER
ARE NOT TO BE USED OR
CIVIL ENGINEER TWO STOREY RESIDENCE SUSAN FORD & GREGORIO APPROVED BY: S.C.C. DATE:
AS SHOWN
S
Carmen, Rosales, Pangasinan
Tel. No. 075-235161 Smart: 09693572413 REPRODUCED WITHOUT THE PRC REQ NO: TIN NO: PILLAR REV. NO: DATE:
WRITTEN AGREEMENT WITH
THE ENGINEER.
PTR NO: DATE: #044 FIRETREE ST. BRGY. TORRES, MAPANDAN, PANGASINAN
OWNER/CLIENT
DRWG. NO: 2 6
 A B
13.010
C D A B c C
2.001 4.550 4.459 2.000
2.000 9.001 2.000
2.840 3.170 3.590 1.400

3.001
3.001
RB-1

3.001

3.001
RB-1
RB-1
1 FB-1 FB-1 FB-1 1
FB-1 FB-1 RB-1

2.100

2.10
FB-1 FB-1
FB-1
FB-2
5.600

FB-2

5.000
FB-1 SLAB 1 SLAB 1 FB-2

5.600
FB-2 FB-2 FB-2

SLAB 1 SLAB 1

5.600
FB-1 FB-1
FB-1

4.400
2
FB-1 FB-1 FB-1 2 FB-1

1.000
FB-1
FB-2

4.000
FB-1 FB-1
15.800

SLAB 1

2.500
4.501

2'

23.000
FB-1 FB-1
SLAB 1 FB-2 SLAB 1 FB-2 FB-1

23.000
SLAB 1

4.000
FB-2
3'

3.000
FB-1 FB-1
3'

3.00
SLAB 1

4.500
1.800

FB-1
3

1.500
FB-1 FB-1 FB-1

FB-1
3 FB-1
FB-1 FB-1 FB-1 SLAB 1 FB-1
SLAB 1
4.000

FB-1

3.900

4.000
FB-1
SLAB 1

6.000
FB-1
4 FB-1 FB-1 FB-1

SLAB 1 4 SLAB 1

8.000
FB-2 FB-1
4.00

FB-2

4.000

2.002
FB-2

2.000 4.550 4.450 2.000

2.400 4.209 2.000
13.000
2.000 4.791 6.209
13.000

1 FLOOR FRAMING PLAN 2 2/F FRAMING & ROOF PLAN

S-03 S-03

R.A. 544 DESIGNER/ CONSULTANT: PROJECT TITLE: OWNER: DRAFTED BY: K.P.P. DATE: SHEET CONTENT: SHEET NO.
KEENUPOWER ALL DOCUMENTS PREPARED
KEENU PAUL PAULO CHECKED BY: S.C.C. DATE:
BUILDERS
AND FURNISHED ARE THE
PROPERTY OF THE ENGINEER
ARE NOT TO BE USED OR
CIVIL ENGINEER TWO STOREY RESIDENCE SUSAN FORD & GREGORIO APPROVED BY: S.C.C. DATE:
AS SHOWN
S
Carmen, Rosales, Pangasinan
Tel. No. 075-235161 Smart: 09693572413 REPRODUCED WITHOUT THE PRC REQ NO: TIN NO: PILLAR REV. NO: DATE:
WRITTEN AGREEMENT WITH
THE ENGINEER.
PTR NO: DATE: #044 FIRETREE ST. BRGY. TORRES, MAPANDAN, PANGASINAN
OWNER/CLIENT
DRWG. NO: 3 6
 TYPICAL SPAN

10-10 mm Ø 100 SUPPORT

250 & REST 10mm Ø @ 200
MIDSPAN.
2 - 16mm Ø TOP BAR

400
2 - 16mm Ø BOTTOM BAR

STIRRUPS: 10 - 10mm Ø @
100 SUPPORT & REST 4- 16 mm DIA. RSB
10mm Ø @ 200 MIDSPAN

SECTION
1 FOOTING TIE BEAM DETAIL
S-04

200

C-2
300

14 EQUAL THREADS VERIFY

12mm Ø @ 0.20 M.O.C
8 - 16 mm dia. RSB TOP BARS
8 - 16 mm dia. Vertical O.C spaced equally 12mm Ø @ 0.15 M.O.C
Bars FLOOR LEVEL
/ LANDING
1200
300

250
100
10 mm. dia. Stirrups
1 at 50mm, 2 at 100mm,
150mm
2 at 150mm, rest at 150

200
200mm O.C.
10mm @ 0.30 M.O.C 12mm Ø @ 0.20

1200
STIFF. BARS TYP. TOP BAR TYP. 2- 12mm Ø TOP &
BOT. BARS
10mm Ø NOSING BARS TYP.
12mm Ø @ 150 W/ 10mmØ STIRR.
CONT.BOTTOM BAR TYP. 1 @ 0.05,
REST @ 0.10 M.O.C
10mm Ø @ 200 TEMP. BAR
1800.00 mm

GROUND LEVEL
NGL

PLAN 10mm Ø @ 0.30 M.O.C. HOR. BARS

150 12mm Ø @ 0.20 M.O.C. VERT. BARS

F1 C2

650
300

6-12mm Ø

300
LONG BARS
50 mm THICK
GRAVEL BED SECTION 16mm Ø @
0.30M.O.C. 1000mm 75mm THK
TRANSV. BAR GRAVEL BEDDING

2 COLUMN-FOOTING DETAILS 3 STAIR DETAIL

S-04 S-04

R.A. 544 DESIGNER/ CONSULTANT: PROJECT TITLE: OWNER: DRAFTED BY: K.P.P. DATE: SHEET CONTENT: SHEET NO.
KEENUPOWER ALL DOCUMENTS PREPARED
KEENU PAUL PAULO CHECKED BY: S.C.C. DATE:
BUILDERS
AND FURNISHED ARE THE
PROPERTY OF THE ENGINEER
ARE NOT TO BE USED OR
CIVIL ENGINEER TWO STOREY RESIDENCE SUSAN FORD & GREGORIO APPROVED BY: S.C.C. DATE:
AS SHOWN
S
Carmen, Rosales, Pangasinan
Tel. No. 075-235161 Smart: 09693572413 REPRODUCED WITHOUT THE PRC REQ NO: TIN NO: PILLAR REV. NO: DATE:
WRITTEN AGREEMENT WITH
THE ENGINEER.
PTR NO: DATE: #044 FIRETREE ST. BRGY. TORRES, MAPANDAN, PANGASINAN
OWNER/CLIENT
DRWG. NO: 4 6
 DESIGNATION AT SUPPORT AT MIDSPAN STIRRUPS

Ø 10MM , 3 @ 50MM,
2 - Ø 16MM CONT. 2 - Ø 16MM CONT.
FTB 3 @ 100MM, 3 @ 150MM
THE REST @ 200MM
TOWARDS MIDSPAN
250 mmW X 400 mmD
2 - Ø 16MM CONT. 2 - Ø 16MM CONT.

2 - Ø 16MM CONT.
Ø 10MM , 3 @ 50MM, SCHEDULE OF COLUMNS
FB - 2
2 - Ø 16MM CONT. 3 @ 100MM, 3 @ 150MM
COL. MARK COL. MARK
200 mmW X 300 mmD
2 - Ø 10MM WEB BARS 2 - Ø 10MM W. BARS THE REST @ 200MM
TOWARDS MIDSPAN
C1 C2 C1 C2
FLOOR LEVEL FLOOR LEVEL
2 - Ø 16MM CONT. 2 - Ø 16MM CONT.

Ø 10MM , 3 @ 50MM, SECOND FLOOR

3 - Ø 16MM CONT. 3 - Ø 16MM CONT. FOUNDATION
3 @ 100MM, 3 @ 150MM
2 - Ø 16MM CUT THE REST @ 200MM
FB - 1 2 - Ø 10MM WEB BARS 2 - Ø 10MM CONT.
TOWARDS MIDSPAN
TO TO
250 mmW X 400 mmD 2 - Ø 16MM CUT
3 - Ø 16MM CONT. 3 - Ø 16MM CONT.
SECOND FLOOR ROOF BEAM

Ø 10MM , 3 @ 50MM,

RB-1/2 3 - Ø 16MM CONT. 2 - Ø 16MM CONT. 3 @ 100MM, 3 @ 150MM

THE REST @ 200MM
SIZE (mm) 400X300 300X200 SIZE (mm) 400X300 300X200
2 - Ø 16MM CUT
TOWARDS MIDSPAN
250 mmW X 400 mmD 2 - Ø 10MM WEB BARS 2 - Ø 10MM CONT. VERT. REINF. 4-25mm Ø & 4-20mmØ 8-20mm Ø VERT. REINF. 8-20mm Ø 8-20mm Ø
2 - Ø 16MM CUT TIES
TIES 1@50mm,2@100mm,3@150mm, rest @ 200mm 1@50mm,2@100mm,3@150mm, rest @ 200mm
2 - Ø 16MM CONT. 3 - Ø 16MM CONT.

1 SCHEDULE OF BEAMS 2 SCHEDULE OF COLUMNS

S-05 S-05

REINFORCEMENT
MARK T ( MM ) PARALLEL TO SHORT SPAN PARALLEL TO LONG SPAN COLUMN TEMP. REMARKS
STRIP BARS
MIDSPAN SUPPORT MIDSPAN SUPPORT

SECOND FLOOR LEVEL

S1 130 Ø12 @ 200 Ø12 @ 200 Ø12 @ 200 Ø12 @ 200 Ø10 @ 200 Ø10 @ 200 TWO WAY

3 SCHEDULE OF SLABS
S-05

R.A. 544 DESIGNER/ CONSULTANT: PROJECT TITLE: OWNER: DRAFTED BY: K.P.P. DATE: SHEET CONTENT: SHEET NO.
KEENUPOWER ALL DOCUMENTS PREPARED
KEENU PAUL PAULO CHECKED BY: S.C.C. DATE:
BUILDERS
AND FURNISHED ARE THE
PROPERTY OF THE ENGINEER
ARE NOT TO BE USED OR
CIVIL ENGINEER TWO STOREY RESIDENCE SUSAN FORD & GREGORIO APPROVED BY: S.C.C. DATE:
AS SHOWN
S
Carmen, Rosales, Pangasinan
Tel. No. 075-235161 Smart: 09693572413 REPRODUCED WITHOUT THE PRC REQ NO: TIN NO: PILLAR REV. NO: DATE:
WRITTEN AGREEMENT WITH
THE ENGINEER.
PTR NO: DATE: #044 FIRETREE ST. BRGY. TORRES, MAPANDAN, PANGASINAN
OWNER/CLIENT
DRWG. NO: 5 6
 A B
13.010
C GA # 26 PRE-PAINTED LONGSPAN GI SHEET
2L 4.5 X 50 L BAR (TOP CHORD)
GA # 26 PRE-PAINTED GI SHEET RIDGE ROLL
2.001 4.550 4.459 2.000 2L 4.5 X 50 L BAR (KING POST)
2L 4.5 X 50 L BAR (BOTTOM CHORD)

SAGROD - 10 MM Ø PRB @ MID SPAN

2L 4.5 X 38 L BAR (WEB MEMBERS)
50mm X 75mm X 1.20mm C-PURLINS @ 0.60M O.C.

USE 50mm X 75mm X 1.20mm

3.001
3.001
C-PURLINS @ 0.60M O.C.
1 RB-1 RB-1

2.100
5.600

5.600
HT-1

TRUSS DETAIL

RB-1
2
S-06
15.800

HT-1
4.501

23.000
2 RB-1 RB-1
4.300

4.500

2.000
1.800

USE 50mm X 75mm X 1.20mm HT-1 USE 50mm X 75mm X 1.20mm

C-PURLINS @ 0.60M O.C. C-PURLINS @ 0.60M O.C.
4.000

RB-1

0.600 0.600 0.600 0.600 0.600 0.800

3.800

HT-1

8.000
RB-1 RB-1
3
4.00

HT-2 HT-2
3.000

1.000
RB-1
4
0.700 0.700 0.700 0.700
2.400 4.209 2.000
2.000 4.791 6.209 2.800
13.000
HT-2

1 ROOF FRAMING PLAN 3 TRUSS DIAGRAM

S-06 S-06

R.A. 544 DESIGNER/ CONSULTANT: PROJECT TITLE: OWNER: DRAFTED BY: K.P.P. DATE: SHEET CONTENT: SHEET NO.
KEENUPOWER ALL DOCUMENTS PREPARED
KEENU PAUL PAULO CHECKED BY: S.C.C. DATE:
BUILDERS
AND FURNISHED ARE THE
PROPERTY OF THE ENGINEER
ARE NOT TO BE USED OR
CIVIL ENGINEER TWO STOREY RESIDENCE SUSAN FORD & GREGORIO APPROVED BY: S.C.C. DATE:
AS SHOWN
S
Carmen, Rosales, Pangasinan
Tel. No. 075-235161 Smart: 09693572413 REPRODUCED WITHOUT THE PRC REQ NO: TIN NO: PILLAR REV. NO: DATE:
WRITTEN AGREEMENT WITH
THE ENGINEER.
PTR NO: DATE: #044 FIRETREE ST. BRGY. TORRES, MAPANDAN, PANGASINAN
OWNER/CLIENT
DRWG. NO: 6 6