TVL 12
ELECTRICAL INSTALLATION &
MAINTENANCE
LEARNER’S MATERIAL
Module
TVL Grade 12
1
PIVOT IV-A Learner’s Material
Quarter 1 Module 1 WEEK
First Edition, 2020
1
GRADE 12
TVL
ELECTRICAL INSTALLATION &
MAINTENANCE
Development Team of the Module
Author: Gerry M. Paragas
Editor:
Reviewer:
Illustrator:
Layout Artist:
Management Team:
1
I What I need to know?
The learners will do the walkthrough of the lesson expectations.
The content of the lesson will be presented as follows:
Electrical tools, equipment and materials for specific job order
The learning objectives will be introduced as follows:
1. Identify the electrical tools, equipment and materials for specific tasks
2. Classify the Electrical tools and equipment according to their uses
3. Discuss the safety precaution in using electrical tools equipment and
materials OHS
NOTE:
Ilagay ang kahon na may kulay kapag hinhayaan ang mag-
2
I What is new?
The learners will answer the prompt questions. They will read about Electrical tools,
equipment and materials for specific job order
Pre/Diagnostic Test
A. Directions: Choose the letter of the correct answer. Use separate answer sheets.
1. It is a machine to bore holes on wood and thin metals
A. Hammer drill B. Portable grinder C. Portable electric drill D. Hand drill
2. This is an instrument designed to measure electric current, voltage, and usually
resistance, typically over several ranges of value.
A. Volt meter B. ammeter C. VOM Multi-tester D. Megger
3. This tool is used for bending conduit in small bends with short segments, for instance,
in order to bend 90° bend.
A. Claw hammer B. Gimlet C. Hickey D. Electricians Plier
4. It is a measuring tape that coils into a compact case.
A. Level bar, B. Foot rule C. Meter stick D. Pull-push rule
5. This tool is used for cutting fine, medium and big wires.
A. Side cutting plier B. Hack saw C. Electricians knife D. Cold Chisel
B. Match Column A with Column B. Write the letter of the correct answer in a separate
sheet.
Column A Column B
1. Danger A.
2. Hand Protection
B.
3. High Voltage
4. Eye Protection Safety
C.
5. Safety Alert
D.
E.
3
D What I know?
The learners will answer the 5 - Items multiple choice.
Identify the tool that is being describe. Write your answer on a separate sheet
of paper.
1. It is used to drive and loosen cross-slotted-screws.
A. Screw driver B. Claw hammer C. Long nose D. Pipe wrench
2. It is used to scrape surface of the conductors and to remove big cable insulation.
A. Wire stripper B. Electricians Knife C. Side cutting plier D. Hack saw
3.This tool is used for measuring the diameter of the wire.
A. American wire gauge B. Pull-push rule C. Foot rule D. Meter stick
4. It is a tool that is commonly used to make terminal loops on copper wire and can
reach in narrow places.
A. Electrician pliers B. Screw diver C. Long nose D. Gimlet
5. It is a hand tool that is used for driving and pulling out nails,
A. Claw hammer B. Hickey C. Hack saw D. Ball-peen
4
D What is in?
Electrical Tools
Long Nose Plier – this is used for holding specially in narrow places
and also used in making terminal loop of copper wires.
Side cutting pliers – this tool is used for cutting fine, medium and big
wires.
Electricians Pliers - his is used in the electrical trade to cut, straighten,
and bend wire, and also to twist wires together when making splices
or joints.
Screw driver -is a tool, manual or powered, used for screwing and un-
screwing screws. A typical simple screwdriver has a handle and a
shaft, ending in a tip the user puts into the screw head before turning
the handle.
Wire stripper - a pair of opposing blade like scissors or wire cutters.
The addition of a center notch makes it easier to cut the insulation
without cutting the wire
Electricians knife - used for removing the insulation of the wire.
Claw hammer - is used for driving and pulling out nails.
American wire gauge (AWG), also known as the Brown &
Sharpe wire gauge, is a logarithmic stepped standardized wire
gauge system used since 1857, predominantly in North America, for
the diameters of round, solid, nonferrous, electrically conducting wire.
Gimlet - is used for boring holes that serves as a screw guide
Hickey -is used to bend conduit in small bends with short segments,
for instance, in order to bend 90° bend.
Hack saw – is used for cutting metal.
Level bar – device for stablishing a horizontal plane. It consist of a
small glass tube containing alcohol or similar liquid and an air bubble;
the tube Is sealed and fix horizontally in a wooden or metallic box or
frame with as smooth lower surface
Pull-push rule — is a measuring tape that coils into a compact case.
5
D What is in?
Pipe wrench - is designed to turn threaded pipe and pipe fittings for
assembly (tightening) or disassembly (loosening). is predominately
used in the plumbing industry.
Heat gun - a handheld device that produces a flameless stream of
extremely hot air, as for rapid drying or for softening paint for re-
moval.
Portable electric drill - Its an tool for drilling holes in wood, thin met-
als and other soft materials. It has a motor, as indicated, by saying its
an electric drill. Its portable, which means the electricity is provided
by an attached rechargeable battery, as opposed to a cord-
ed drill that must be plugged in a wall socket.
VOM Multi-tester –an instrument designed to measure electric cur-
rent, voltage, and usually resistance, typically over several ranges of
value.
Digital clamp meter is an electrical test tool that combines a
basic digital multimeter with a current sensor beneath their plastic
moldings, hard jaws consist of ferrite iron and are engineered to de-
tect, concentrate and measure the magnetic field being generated by
current as it flows through a conductor.
8 Safety Precautions Every Electrician Student Should Know
Don't touch someone who's been electrocuted! ...
Know your Electrical Code. ...
Always use GFCIs in damp or wet work areas. ...
Inspect & maintain your electrical tools. ...
Follow proper lockout/tagout procedures. ...
Wear the right safety gear. ...
Choose the right ladder
Avoid power lines
Most important rule of electrical safety
- Never work on an energized circuit except if the power can not be disconnected.
6
D What is in?
Safety Symbols
HAND PROTECTION: safety signs are a visual reminder of the
need to use personal protective equipment (PPE) in the work-
place. The signs indicate the need to use the appropriate pro-
tective hand wear.
PROHIBITION: the act of prohibiting
The EYE PROTECTION SAFETY sign indicates there is the possi-
bility of chemical, environmental, radiological, or mechanical
irritants and hazards in the laboratory.
HIGH VOLTAGE: This symbol indicates high voltage. It calls your
attention to items or operations that could be dangerous to
you and other persons operation this equipment.
This symbol is the “Safety Alert Symbol.” It occurs with either of
two signal words: CAUTION or WARNING, as described below.
SAFETY ALERT: are a medium of communication that convey
information or instructions regarding the physical safety of peo-
ple. Safety signs should adhere to the latest risk communication
best practices as defined by various regulatory and standards
bodies like OSHA, ANSI and ISO.
DANGER: It indicates and imminently hazardous situation
which, if not avoided, may result to serious injury or death.
WARNING: It indicates a potentially hazardous situation
which, if not avoided, may result to serious injury or death.
CAUTION: It indicates a potentially hazardous situation
which, if not avoided, may result in minor or major injury.
CAUTION: It indicates a potentially hazardous situation
which, if not avoided, may result in property damage.
7
D What is in?
Electrical Materials
8
D What is it?
The learners will identify the pictures of specific tools and equipment’s for spe-
cific task. Write your answers in separate sheet.
Electrical Tools
9
E What is more?
Directions: Match the pictures Column A with the correct name in Column B.
Write your answer in separate sheet
Column A Column B
10
E What I can do?
Proper Tool Storage and Safety Symbols
Directions: On a separate sheet of paper, write T if the statement Is correct and
F if it is false.
____ 1. All tools can be used as hammer.
____ 2. Level bar is an example of testing tool.
____ 3. Light tools and equipment should be place at he
lowest part of the cabinet.
____ 4.Tooth cutting tools should be sharpened as open as
necessary.
____ 5. Tools and equipment must be stored according to
their kind.
____ 6. Warning indicates and imminently hazardous situation which, if not avoided,
may result to serious injury or death.
____ 7. Hand Protection indicates there is the possibility of chemical, environmental,
radiological, or mechanical irritants and hazards in the laboratory.
____ 8. Caution indicates a potentially hazardous situation which, if not avoided,
may result in minor or major injury.
____ 9. Safety alert are a medium of communication that convey information or in-
structions regarding the physical safety of people.
____ 10. Eye Protection Safety The signs indicate the need to use the appropriate
protective hand wear
11
E What else can I do?
Directions: classify the given pictures of electrical tools below. use the given answer sheet.
Classification of Tools
Measuring
Holding Tools Cutting Tools Boring Tools Testing Tools Power Tools
Tools
Electrical Tools
12
A What I have learned?
Enumeration.
Directions:
1. Write 5 Safety Precautions Every Electrician Student Should Know
2. Write 5 Electrical tools
Electricity is being used all around us – at school, at home and elsewhere
in the community. There are important things to know to stay safe around elec-
tricity.
Directions: In a separate sheet, Make a list some ways you can stay safe around
electricity selecting appropriate Electrical tools equipment and materials for the
specific task.
A What I can achieve?
Post-Test/
A. Multiple choice
A. Directions: Choose the letter of the correct answer. Use separate answer sheets.
1. This tool is used for bending conduit in small bends with short segments, for instance,
in order to bend 90° bend.
A. Claw hammer B. Gimlet C. Hickey D. Electricians Plier
2. It is a measuring tape that coils into a compact case.
A. Level bar, B. Foot rule C. Meter stick D. Pull-push rule
3. It is a power tool used to bore holes on wood and thin metals
A. Hammer drill B. Portable grinder C. Portable electric drill D. Hand drill
4. This is an instrument designed to measure electric current, voltage, and usually
resistance, typically over several ranges of value.
A. Volt meter B. ammeter C. VOM Multi-tester D. Megger
5. This tool is used for cutting fine, medium and big wires.
A. Side cutting plier B. Hack saw C. Electricians knife D. Cold Chisel
6. It is a tool that is commonly used to make terminal loops on copper wire and can
reach in narrow places.
A. Electrician pliers B. Screw diver C. Long nose D. Gimlet
7. It is used to scrape surface of the conductors and to remove big cable insulation.
A. Wire stripper B. Electricians Knife C. Side cutting plier D. Hack saw
13
A What I can achieve?
8.This tool is used for measuring the diameter of the wire.
A. American wire gauge B. Pull-push rule C. Foot rule D. Meter stick
9. It is used to drive and loosen cross-slotted-screws.
A. Screw driver B. Claw hammer C. Long nose D. Pipe wrench
10. It is a hand tool that is used for driving and pulling out nails,
A. Claw hammer B. Hickey C. Hack saw D. Ball-peen
B. 1dentify the following pictures of electrical materials.
14
Answer
What is new? What I know? What is more?
1. B 6. E 1. A 1. I 6. C
2. C 7. C 2. C 2. H 7. E
3. C 8. A 3. A 3. G 8. A
4. D 9. D 4. C 4. D 9. B
5. A 10. B 5. A 5. F 10. J
What is it?
1. Digital Clamp meter 6.Wire stripper 11. Side cutting plier
2. Electricians knife 7. Level bar 12. Screw driver
3. Portable electric drill 8. Hack saw 13. Claw hammer
4. Pipe wrench 9. American wire gauge 14. Electrician pliers
5. Heat gun 10. Pull-push rule 15. Gimlet
What I can do? What I can achieve?
1. F 6. T 1. C 6. C 11. Switch
2. T 7. F 2. D 7. B 12. Wire
3. F 8. T 3. C 8. A 13. Hanging socket
4. T 9. T 4. C 9. A 14. Junction box
5. T 10. F 5. A 10. A 15. Circuit breaker
What else can I do?
Classification of Tools
Measuring Testing
Holding Tools Cutting Tools Boring Tools Power Tools
Tools Tools
Long nose pliers Hack saw Gimlet Digital Clamp me- Level bar Portable electric
ter drill
Pipe wrench Electricians VOM Multi-tester Heat gun
knife
Electricians pli- Side cutting pli- Pull push rule
ers ers
Wire stripper
15
Reference
TVL Industrial Arts Electrical Installation and Maintenance Module 1
Learner’s Material:
www.naugraexport.com/portable-electric-drill
https://uk.rs-online.com/web/p/heat-guns/7932614/https://
tolsen.com.ph/products/electrician-s-knife
https://www.omniphilippines.com.ph/product/wub-001/
https://lsgindustrial.com/product/omni-e27-ceiling-receptacle-model
-e27-040/
16
