Scribd
Upload
140 views1 page

Computer Aided Engineering Drawing - Important Questiuons For IA2

Uploaded by

Tanmayi Maram
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
140 views1 page

Computer Aided Engineering Drawing - Important Questiuons For IA2

Uploaded by

Tanmayi Maram
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

Computer Aided Engineering Drawing – BCEDK203

Important Questions for IA2


1) A triangular prism base side 30mm and length 70mm is resting on rectangular face on top of a square slab of
side 70mm and 25mm thickness. Draw the isometric projections.
2) A frustum of cone of base dia 50mm, top dia 25mm and height 50mm is placed centrally on the top face of
the cylinder dia 60mm and height 60mm. Draw the isometric projection of the combination.
3) A regular pentagonal prism of base edge 30mm and axis 60mm is mounted centrally over a cylindrical block
of 80mm diameter and 25mm thick. Draw the isometric projection of the combined solids.
4) A rectangular pyramid of base 40mmx25mm and height 50mm is placed centrally on rectangular slab sides
100mmx60mm and thickness-20mm.Draw the isometric projection of the combination.
5) A vertical cylinder of base diameter 45mm & axis length 60mm is cut by a plane perpendicular to VP & inclined
at 50deg to HP, is passing through the center point of the face. Draw the development of the lateral surface of
the cylinder.
6) A regular pentagonal pyramid of side of base 35mm & altitude 65mm has its base on HP with a side of base
perpendicular to VP. The pyramid is cut by a section plane which is perpendicular to the VP & inclined at the
30degto HP. The cutting plane meets the axis of the pyramid at a point 30mm below the vertex. Obtain the
development of the remaining part of the pyramid.
7) A square prism of base side 40mm and axis length 65mm is resting on HP on its base with all the vertical faces
being equally inclined to VP. It is cut by an inclined plane 60°. to HP & perpendicular to VP and is passing through
a point on the axis at a distance 15mm from the top face. Draw the development of the lower portion of the
prism.
8) A hexagonal prism of base side 20mm & height 50mm is resting on HP on its base, such that one of its base
edges is parallel to VP. The prism is cut in this position as shown in the following front view fig.1. Draw the
development of the lateral surface of the prism.

9) A cone of base diameter 50mm and height 40mm is placed centrally on the top face of a square slab side-
80mm and height 20mm. Draw the isometric projection of the combination.
10) The frustum of a square pyramid of base sides 40mm top face side 20mm and height 60mm rest on the
center of the top of a square block of side 60mm and height 20mm. The base edges of the pyramid are
parallel to the top edges of the square block. Draw the isometric projection of the combination of the solids.
11) A square prism of base side 40mm and axis length 65mm is resting on HP on its base with all the vertical
faces equally inclined to VP. It is cut by an inclined plane 60˚to HP and perpendicular to VP and passes through
a point on the axis at a distance of 15mm from the top face. Draw the development of the lower portion of
the prism.
12) A cone of base diameter 60mm & height 70mm is resting on its base on HP. It is cut as shown in following
figure.4. Draw the development of the lateral surface of the remaining portion of the cone.

You might also like