NAMA PROGRAM : PEMASANGAN DAN PENYELENGGARAAN ELEKTRIK TIGA FASA

PROGRAM : [F432-005-3:2019]

 SALINAN KAD PENGENALAN (1 SALINAN – BY WHATSAPP)

 CARTA ORGANISASI TEMPAT KERJA (1 SALINAN – BY WHATSAPP)
 GAMBAR BERUKURAN PASPORT (BY WHASAPP)
 SETIAP BUKTI PERLU ADA TERTULIS NAMA FAUZI
 ARAHAN DALAM WS DAN TERTERA NAMA FAUZI BOLEH DITERIMA SEBAGAI BUKTI
(SCREENSHORT WS) / SIJIL YANG BERKAITAN
 BOLEH RUJUK JENIS-JENIS BUKTI DI BAHAGIAN PAGES AKHIR
 SILA TANDAKAN NOTA, CONTOH CU1.1 UNTUK SETIAP BUKTI GAMBAR

BIL. PERKARA BUKTI

1. THREE PHASE DRAWING
1 Prepare Three Phase Drawing Requirements. (2 BUKTI) Gambar @
- Carry out site survey. laporan @
- Calculate Total Connected Load (TCL). memo
- Calculate current diversity value. arahan/arahan
- Determine maximum demand. bertulis @
* pilih 2 point yang dokumen/bukti sedia ada dengan fauzi senarai semak

2 Perform Three Phase Drawing. (2 BUKTI) Laporan @

- Draw layout plan. senarai semak @
- Determine final circuit distribution. plan lukisan
- Draw three line schematic diagram.
* pilih 2 point yang dokumen/bukti sedia ada dengan fauzi

3 Propose Three Phase Drawing Paperwork. (2 BUKTI) Contoh lukisan

- Sample of three phase drawing paperwork. @ gambar @
- Compile three phase drawing paperwork. memo arahan @
- Check drawing for error. senarai semak @
- Check drawing for error. laporan
* pilih 2 point yang dokumen/bukti sedia ada dengan fauzi

2. THREE PHASE WIRING

1 Prepare Three Phase Wiring Requirements. (2 BUKTI) Senarai semak @
- Interpret wiring requirements. surat berkaitan
- Select wiring and earthing work tools and equipment. @ laporan @
- Select wiring and earthing materials. gambar
- Determine location of wiring route.
* pilih 2 point yang dokumen/bukti sedia ada dengan fauzi

2 Perform Three Phase Wiring Activities. (2 BUKTI) Gambar @

- Setup safe working area. senarai semak @
 - Conduct three phase framework installation (surface, conceal, conduit, laporan @
ducting, trunking, casing, cable tray and underground). memo arahan
- Lay and mark cable.
- Determine location for fitting and accessories installation.
- Carry out cables and accessories termination.
- Check all fitting & accessories connected to earthing.
- Check all fitting & accessories connected to earthing.
- Determine earthing location.
- Test earthing system using earth tester.
- Connect earth point busbar to earth rod.
- Execute electrical testing on wiring system.
- Execute visual check on wiring system finishing.
* pilih 2 point yang dokumen/bukti sedia ada dengan fauzi

3 Carry Out Three Phase Distribution Board Installation. (2 BUKTI) Gambar @

- Mark distribution board installation location. senarai semak @
- Install distribution board. laporan
- Install protection device in distribution board.
- Connect wiring cable and earthing cable onto distribution board.
- Execute insulation resistance test on wiring system.
* pilih 2 point yang dokumen/bukti sedia ada dengan fauzi

3. THREE PHASE SYSTEM MAINTENANCE

1 Prepare Maintenance Work Requirement. (2 BUKTI) Senarai
- Maintenance procedure which include: • Work order. • Maintenance kerja/tugas @
schedule. • Work specification (schematic plan, layout plan, checklist). • laporan @
Safety (PPE). gambar
- Maintenance checklist format.
- Interpret system maintenance requirements.
- Select maintenance work tools and equipment.
- Determine location of maintenance.
* pilih 2 point yang dokumen/bukti sedia ada dengan fauzi

2 Perform Maintenance Work. (2 BUKTI) Gambar @

- Troubleshooting procedure.
senarai semak @
- Maintenance technique which include: • Service. • Repair. • Replace.
laporan
- Types of faulty which include: • Electrical fault. • Mechanical fault.
- Functionality test.
- Inspect system functionality and condition.
- Execute parts maintenance.
- Identify parts faulty
- Rectify faulty parts.
- Utilise testing tools and equipment.
* pilih 2 point yang dokumen/bukti sedia ada dengan fauzi
 3 Prepare Maintenance Work Report. (2 BUKTI) Laporan @
- Update maintenance checklist and logbook. senarai semak @
- Produce maintenance report. surat berkaitan
- Submit maintenance report. @ gambar
- File maintenance report.
* pilih 2 point yang dokumen/bukti sedia ada dengan fauzi

4. THREE PHASE MOTOR SYSTEM INSTALLATION Gambar @

1 Prepare Three Phase Motor System Installation Requirements. senarai semak @
(2 BUKTI) laporan @
- Interpret motor system installation requirements. memo arahan
- Select motor system installation tools and equipment.
- Select motor system installation materials.
- Select motor system testing equipment.
- Determine motor and motor control installation location.
* pilih 2 point yang dokumen/bukti sedia ada dengan fauzi

2 Carry Out Three Phase Motor Installation And Termination. Gambar @

(2 BUKTI) laporan @
- Setup safe working area. senarai semak
- Mark motor installation location.
- Install motor.
- Execute motor winding resistance test.
- Execute motor winding resistance test.
- Record motor name plate.
* pilih 2 point yang dokumen/bukti sedia ada dengan fauzi

3 Carry Out Three Phase Motor Control Installation. (2 BUKTI) Gambar @

- Determine location for fitting and accessories installation. senarai semak @
- Execute wiring and marking cable. memo arahan @
- Execute motor control installation (Direct Online (DOL) starter, Star surat berkaitan
Delta (SD) starter, Auto Transformer (AT) starter, Rotor Resistance @ laporan
starter).
- Execute motor and motor control termination including grounding.
* pilih 2 point yang dokumen/bukti sedia ada dengan fauzi

4 Test Three Phase Motor And Motor Control Functionalities. Gambar @

(2 BUKTI) senarai semak @
- Execute dead circuit test (insulation, continuity, polarity). laporan @
- Execute live circuit test (on load and off load, rotation direction). memo arahan
- Analyse test result.
- Record test data.
* pilih 2 point yang dokumen/bukti sedia ada dengan fauzi

5. THREE PHASE WIRING TESTING AND COMMISSIONING

 1 Prepare Three Phase Electrical System Testing And Senarai semak @
Commissioning Requirements. (2 BUKTI) gambar @
- Apply work permission and Permit to Work (PTW). senarai semak @
- Interpret work information from safety briefing. memo arahan @
- Request Permit to Work (PTW) approval. laporan
- Select testing and commissioning work tools and equipment.
* pilih 2 point yang dokumen/bukti sedia ada dengan fauzi

2 Perform Three Phase Electrical System Testing. (2 BUKTI) Gambar @

- Prepare safe working area (Notice, PTW, shutdown, LOTO, PCD, CME). senarai semak @
- Execute continuity test. laporan @
- Execute polarity test. memo arahan
- Execute insulation resistance test.
- Execute phase sequence test.
- Execute earthing resistance test.
- Execute Residual Current Device (RCD) test.
- Execute earth loop impedance test.
- Execute illumination test.
- Execute motor and motor control testing (on load and off load).
- Apply PTW closure.
- Carry out housekeeping work.
* pilih 2 point yang dokumen/bukti sedia ada dengan fauzi

3 Perform Three Phase Electrical System Commissioning. Gambar @

(2 BUKTI) laporan @
- Prepare safe working area (Notice, PTW, shutdown, LOTO, PCD, CME). senarai semak @
- Update inspection check sheet. memo arahan
- Compile testing result.
- Compare test result (electrical installation guideline).
- Obtain competent personnel endorsement.
- Obtain owner acceptance.
- Apply Permit to Work (PTW) closure.
* pilih 2 point yang dokumen/bukti sedia ada dengan fauzi

6. ELECTRICAL BUILDING AUTOMATION SYSTEM INSTALLATION

1 Prepare Electrical BAS Installation Requirement. (2 BUKTI) Gambar @
- Interpret wiring schematic drawing. senarai semak @
- Interpret layout plan. memo arahan @
- Carry out site visit and evaluation. surat berkaitan
- Identify types of load. @ laporan
- Determine appropriate BAS devices (sensor and actuator).
- Check location of the wiring route.
* pilih 2 point yang dokumen/bukti sedia ada dengan fauzi

2 Produce Electrical BAS Schematic Drawing. (2 BUKTI)

 - Interpret BAS blueprint. Contoh plan @
- Plan BAS topology. senarai semak @
- Address BAS device. gambar @
- Produce electrical BAS schematic drawing. memo arahan
- Layout plan elements which include: • Symbols. • Loads. • Accessories.
• Legends.
* pilih 2 point yang dokumen/bukti sedia ada dengan fauzi

3 Install Electrical BAS System. (2 BUKTI) Gambar @

- Setup safe working area. senarai semak @
- Determine location for BAS device installation. memo arahan @
- Conduct BAS framework installation (hacking, drilling, levelling, laporan
plastering and painting).
- Lay and mark AC load cable.
- Lay BAS cable.
- Interpret BAS devices technical manual.
- Execute BAS devices installation.
- Carry out AC load and BAS cables termination
- Inspect BAS installation
* pilih 2 point yang dokumen/bukti sedia ada dengan fauzi

4 Perform Electrical BAS Device Programming. (2 BUKTI) Gambar @

- Import BAS device database. laporan @
- Create BAS project. memo arahan @
BAS project: • Building view (building structure, BAS device). • Group senarai semak
address view (organised main group, middle group & group addresses).
- Identify device functionality.
- Assign group address.
* pilih 2 point yang dokumen/bukti sedia ada dengan fauzi

5 Perform Electrical BAS System Testing And Commissioning. Gambar @

(2 BUKTI) memo arahan @
- Connect BAS software and BAS system. senarai semak @
- Test BAS software and BAS system interface. laporan
- Download BAS program to device.
- Carry out BAS device functionality test and commissioning.
- Carry out diagnostics.
- Prepare BAS functionality form.
- Carry out housekeeping work.
* pilih 2 point yang dokumen/bukti sedia ada dengan fauzi

7. ELECTRICAL INSTALLATION & MAINTENANCE SUPERVISORY

1 Prepare Project Costing. (2 BUKTI) Gambar @
- Determine operation cost. memo arahan @
 Types of operation cost which include: • Materials. • Tools and laporan @
equipment. • Labour cost. senarai semak
- Calculate project cost.
- Propose project costing estimation.
Materials costing requirements which include: • Cable (size, cable type,
quantity). • Fitting (conduit, trunking, casing). • Accessories (types of
accessories and quantity). • Sundry items.
Tools and equipment which include: • Hand tools. • Power tools. • Test
and measurement equipment.
Labour cost: • Competency. • Work duration.
* pilih 2 point yang dokumen/bukti sedia ada dengan fauzi

2 Supervise Safety And Health Practice. (2 BUKTI) Gambar @

- Conduct safety and health briefing. memo arahan @
- Convey information to staff. surat berkaitan
- Monitor PPE usage among workers. @ laporan
- Conform working process to Standard Operating Procedure (SOP).
* pilih 2 point yang dokumen/bukti sedia ada dengan fauzi

3 Supervise Work Progress. (2 BUKTI) Senarai semak @

- Conduct project briefing. senarai tugas/
- Convey information to staff. kerja @ memo
- Determine work completion date. arahan @
- Arrange manpower requirement. laporan @
- Check work performance against work schedule. gambar
- Compile project progress and commissioning report.
- Recommend improvement for the project
- Present progress report.
* pilih 2 point yang dokumen/bukti sedia ada dengan fauzi

JENIS-JENIS BUKTI SUMBER DIPEROLEHI /SYARAT

KATEGORI BUKTI KUKUH KATEGORI BUKTI SEDERHANA

1. Memo/Surat 1. Hasil Kerja - Dihasilkan sebelum permohonan
Lantikan/Arahan kerja dikemukakan. - Disahkan secara bertulis oleh
▪ Majikan, Pusat Bertauliah(PB) atau agensi pelanggan/majikan atau pihak ketiga*
awam/swasta 2. Perakuan PP-PPT - Laporan hasil lawatan di
yang berkenaan tempat kerja calon - Laporan temuduga
▪ Disahkan oleh pegawai atasan [Laporan Penilaian Bukti-Bukti Keterampilan
2. Senarai Tugas ▪ Disahkan oleh pegawai Pengiktirafan Pencapaian Terdahulu (PPT)]
atasan atau majikan. 3. Testimonial (Pelanggan) - Merupakan
3. Lesen pelanggan kepada calon
▪ Dikeluarkan oleh Badan Pelesenan yang 4. Keratan Akhbar - Dokumen asal dan disahkan
diiktiraf. oleh majikan atau pihak ketiga*
4. Buku Log/Buku 5. Artikel - Dokumen asal dan bertarikh serta
Catatan ▪ Rujuk kepada dokumen asal buku disahkan oleh majikan atau pihak ketiga*
log/buku catatan. 6. Bil/Resit/Inbois - Salinan bukti perlu
▪ Disahkan oleh pegawai atasan. disertakan bersama dokumen asal bagi tujuan
5. Surat Akuan semakan PP-PPT dan PPL-PPT
▪ Majikan, Pusat Bertauliah atau agensi 7. Sampel - Dilihat dan disahkan oleh PP-PPT
awam/swasta dan PPL-PPT.
8. ROC/ROB/ROS ▪ Suruhanjaya Syarikat 8. Video/CD - Salinan bukti perlu disertakan
Malaysia (SSM) bersama dokumen asal bagi tujuan semakan
7. Keputusan Penilaian PP-PPT dan PPL-PPT
/ Ujian/ Peperiksaan 9. Dokumen ISO - Salinan bukti perlu disertakan
▪ Dikeluarkan oleh badan/agensi yang diiktiraf bersama dokumen asal bagi tujuan semakan
▪ Salinan bukti perlu disertakan bersama PP-PPT dan PPL-PPT
dokumen asal 10. Fail Meja - Salinan bukti perlu disertakan
8. Kertas Kerja ▪ Telah diluluskan oleh majikan bersama dokumen asal bagi tujuan semakan
atau pihak ketiga* PP-PPT dan PPL-PPT
9. Laporan ▪ Telah diluluskan oleh majikan atau 11. Gambar - Diambil sebelum permohonan
pihak ketiga* dikemukakan. - Disahkan secara bertulis oleh
10. Rekabentuk/ majikan/rakan sekerja/pihak ketiga*.
Blueprint
▪ Bukti disediakan oleh calon Nota : *Pihak Ketiga adalah Pesuruhjaya
▪ Salinan bukti yang disahkan oleh majikan atau Sumpah, Jaksa Pendamai, Ketua Kampung,
pihak ketiga* Penghulu atau Pegawai Pengurusan &
11. Sijil Kursus Professional
▪ Daripada agensi yang diiktiraf sama ada
institut
awam/swasta
▪ Disertakan dengan transkrip, jadual waktu
atau isi
kandungan kursus yang berkaitan
12. . Anugerah ▪ Diiktiraf oleh badan atau
agensi di peringkat kebangsaan
atau antarabangsa

Nota : *Pihak Ketiga adalah Pesuruhjaya

Sumpah, Jaksa Pendamai, Ketua Kampung,
Penghulu atau
Pegawai Pengurusan & Professional