FlowCon SM

The most Advanced PICV in the World with User-friendly Actuator

The FlowCon SM valve is a pressure independent All together, the choice for FlowCon SM will avoid
dynamic control valve, which automatically keeps extensive calculations, assessment of valve autho-
a constant differential pressure across the internal rity and over-sized control valves.
controlling orifice of the valve. FlowCon SM valve
setting will limit flow to design flow at full load, and • 100% authority pressure independent -
the FlowCon SM actuator will precisely and with for any of each valve’s 51 max. flow settings.
full authority limit the flow requirement at any par- • User-friendly touch panel actuator for easy
tial load. The dynamic flow characteristics keep the setting of flow, control input, control mode etc.
FlowCon SM in constant authority and automati- • Display actuator as well as actuator feedback
cally balanced. This ensures delivery of precisely to BMS allow monitoring of valve performance.
the flow rate required by each unit, independent of • Optional failsafe and BACnet actuator ver-
pressure fluctuations in the hydronic system. sions available.
• Wide range from DN15-250 (1/2”-10”) all using
The FlowCon SM is a 100% authority pressure in- the same type actuator - an easy solution for
dependent flow control valve, which instantaneous- designers, installers and end-users.
ly self-balance at all points of operation, even when • Multi-rotational actuator - for precise position
there is variance in pressure differential. As long as of the spindle providing accurate flow.
the differential pressure across the valve is within • Multiple control modes included providing
the operation range, the Kv of the valve is regulated high accuracy.
nonstop to keep the control valve in full authority.
 FlowCon SM
The most Advanced PICV in the World with User-friendly Actuator
PICV with actuator SM actuator
Maintains correct flow despite pressure changes All SM valves can be fitted with the same type
and guarantees that flow and actuator position only state-of-the-art actuator, which both in design and
change when demand requirements change. user-friendliness is unique. All features are selected
Size: DN15-250 (1/2”-10”). directly on the touch panel or remotely via BACnet.
Max. operational ΔP: SM.1/2: 320 kPaD / 46 psid. The actuator display continuously shows current
SM.3/4/5/6: 800 kPaD / 116 psid. flow rate and a range of additional valve information.
Max. flow rates: 0.176-76.8 l/sec / 2.79-1220 GPM. The SM actuator is electrical 0(2)-10V or 0(4)-20mA
Media temperature: -20°C to +120°C / -4°C to +248°F. modulating, 3-point floating or 2-position in one and
Static Pressure: SM.1/2: 2500 kPa / 360 psi. the same unit and always with feedback.
SM.3/4/5/6: 4000 kPa / 580 psi.
Housings Applications
The FlowCon SM is available 6 different housing The FlowCon SM is designed for HVAC installations.
sizes covering: The 2-way regulation/control valve is used: in radia-
• SM.1 - DN15-25 (1/2”-1”), union end connections. tor heating circuits and inverted heat systems, on
• SM.2 - DN25-40 (1”-1 1/2”), union end connections. fan coil units, air handler units, CRAC units, heat
• SM.3 - DN50-80 (2”-3”), flange connection. exchangers and hot water tank systems - wherever
• SM.4 - DN80-100 (3”-4”), flange connection. dynamic balancing and fully accurate temperature
• SM.5 - DN125-150 (5”-6”), flange connection. control are required.
• SM.6 - DN200-250 (8”-10”), flange connection.
For further information visit www.flowcon.com

Application Example
CRAC Unit, Computer Room Air Condition with PICV Direct Control.
FlowCon International can accept no responsibility for possible errors in any printed material. All rights reserved. 01.2020

CRAC Unit

Controller

FlowCon SM

Pump

www.flowcon.com
D E N M A R K • D U B A I • U S A • C H I N A • S I N G A P O R E